DPDK patches and discussions
 help / color / mirror / Atom feed
* [dpdk-dev] [PATCH V2] doc: fix vhost setup in tep-termination app guide
@ 2016-07-21 13:10 Mark Kavanagh
  2016-07-22 16:13 ` Thomas Monjalon
  0 siblings, 1 reply; 4+ messages in thread
From: Mark Kavanagh @ 2016-07-21 13:10 UTC (permalink / raw)
  To: dev

- Fix vhost setup flags
- Add minor edits to improve readability and consistency

---

v2: - revert file mode changes made erroneously in v1

Signed-off-by: Mark Kavanagh <mark.b.kavanagh@intel.com>
---
 doc/guides/sample_app_ug/tep_termination.rst | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/doc/guides/sample_app_ug/tep_termination.rst b/doc/guides/sample_app_ug/tep_termination.rst
index 2d86a03..c3d1e97 100644
--- a/doc/guides/sample_app_ug/tep_termination.rst
+++ b/doc/guides/sample_app_ug/tep_termination.rst
@@ -59,8 +59,8 @@ This allows network isolation, QOS, etc to be provided on a per client basis.
 In a typical setup, the network overlay tunnel is terminated at the Virtual/Tunnel End Point (VEP/TEP).
 The TEP is normally located at the physical host level ideally in the software switch.
 Due to processing constraints and the inevitable bottleneck that the switch
-becomes the ability to offload overlay support features becomes an important requirement.
-Intel® XL710 10/40 G Ethernet network card provides hardware filtering
+becomes, the ability to offload overlay support features becomes an important requirement.
+Intel® XL710 10/40 Gigabit Ethernet network card provides hardware filtering
 and offload capabilities to support overlay networks implementations such as MAC in UDP and MAC in GRE.
 
 Sample Code Overview
@@ -131,14 +131,14 @@ Compiling the Sample Code
 
     .. code-block:: console
 
-        CONFIG_RTE_LIBRTE_VHOST=n
+        CONFIG_RTE_LIBRTE_VHOST=y
 
     vhost user is turned on by default in the configure file config/common_linuxapp.
     To enable vhost cuse, disable vhost user.
 
     .. code-block:: console
 
-        CONFIG_RTE_LIBRTE_VHOST_USER=y
+        CONFIG_RTE_LIBRTE_VHOST_USER=n
 
      After vhost is enabled and the implementation is selected, build the vhost library.
 
-- 
1.9.3

^ permalink raw reply	[flat|nested] 4+ messages in thread
* [dpdk-dev] [PATCH V2] doc: fix vhost setup in tep-termination app guide
@ 2016-07-21 13:04 Mark Kavanagh
  2016-07-21 13:13 ` Kavanagh, Mark B
  0 siblings, 1 reply; 4+ messages in thread
From: Mark Kavanagh @ 2016-07-21 13:04 UTC (permalink / raw)
  To: dev

- Fix vhost setup flags
- Add minor edits to improve readability and consistency

---

v2: - revert file mode changes made erroneously in v1

Signed-off-by: Mark Kavanagh <mark.b.kavanagh@intel.com>
---
 doc/guides/sample_app_ug/tep_termination.rst | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
 mode change 100644 => 100755 doc/guides/sample_app_ug/tep_termination.rst

diff --git a/doc/guides/sample_app_ug/tep_termination.rst b/doc/guides/sample_app_ug/tep_termination.rst
old mode 100644
new mode 100755
index 2d86a03..c3d1e97
--- a/doc/guides/sample_app_ug/tep_termination.rst
+++ b/doc/guides/sample_app_ug/tep_termination.rst
@@ -59,8 +59,8 @@ This allows network isolation, QOS, etc to be provided on a per client basis.
 In a typical setup, the network overlay tunnel is terminated at the Virtual/Tunnel End Point (VEP/TEP).
 The TEP is normally located at the physical host level ideally in the software switch.
 Due to processing constraints and the inevitable bottleneck that the switch
-becomes the ability to offload overlay support features becomes an important requirement.
-Intel® XL710 10/40 G Ethernet network card provides hardware filtering
+becomes, the ability to offload overlay support features becomes an important requirement.
+Intel® XL710 10/40 Gigabit Ethernet network card provides hardware filtering
 and offload capabilities to support overlay networks implementations such as MAC in UDP and MAC in GRE.
 
 Sample Code Overview
@@ -131,14 +131,14 @@ Compiling the Sample Code
 
     .. code-block:: console
 
-        CONFIG_RTE_LIBRTE_VHOST=n
+        CONFIG_RTE_LIBRTE_VHOST=y
 
     vhost user is turned on by default in the configure file config/common_linuxapp.
     To enable vhost cuse, disable vhost user.
 
     .. code-block:: console
 
-        CONFIG_RTE_LIBRTE_VHOST_USER=y
+        CONFIG_RTE_LIBRTE_VHOST_USER=n
 
      After vhost is enabled and the implementation is selected, build the vhost library.
 
-- 
1.9.3

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~2016-07-22 16:13 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-07-21 13:10 [dpdk-dev] [PATCH V2] doc: fix vhost setup in tep-termination app guide Mark Kavanagh
2016-07-22 16:13 ` Thomas Monjalon
  -- strict thread matches above, loose matches on Subject: below --
2016-07-21 13:04 Mark Kavanagh
2016-07-21 13:13 ` Kavanagh, Mark B

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).