From: Xiao Zhang <xiao.zhang@intel.com>
To: dev@dpdk.org
Cc: Xiao Zhang <xiao.zhang@intel.com>
Subject: [dpdk-dev] [DPDK] net/e1000: Intel i219 reset hang issue fix.
Date: Thu, 4 Jul 2019 19:24:47 +0800 [thread overview]
Message-ID: <1562239487-34431-1-git-send-email-xiao.zhang@intel.com> (raw)
Unit hang may occur if multiple descriptors are available in the rings during
reset or close. Flush them before reset or close to avoid the issue.
Change-Id: Ia5e8dd06ad890d19f5093f1696faf68f7f52b491
Signed-off-by: Xiao Zhang <xiao.zhang@intel.com>
---
drivers/net/e1000/base/e1000_ich8lan.h | 1 +
drivers/net/e1000/e1000_ethdev.h | 1 +
drivers/net/e1000/igb_ethdev.c | 5 ++
drivers/net/e1000/igb_rxtx.c | 89 ++++++++++++++++++++++++++++++++++
4 files changed, 96 insertions(+)
diff --git a/drivers/net/e1000/base/e1000_ich8lan.h b/drivers/net/e1000/base/e1000_ich8lan.h
index bc4ed1d..1f2a3f8 100644
--- a/drivers/net/e1000/base/e1000_ich8lan.h
+++ b/drivers/net/e1000/base/e1000_ich8lan.h
@@ -120,6 +120,7 @@ POSSIBILITY OF SUCH DAMAGE.
#define E1000_FEXTNVM7_SIDE_CLK_UNGATE 0x00000004
#if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT)
#define E1000_FEXTNVM7_DISABLE_SMB_PERST 0x00000020
+#define E1000_FEXTNVM7_NEED_DESCRING_FLUSH 0x00000100
#endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */
#define E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS 0x00000800
#define E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS 0x00001000
diff --git a/drivers/net/e1000/e1000_ethdev.h b/drivers/net/e1000/e1000_ethdev.h
index 67acb73..3451979 100644
--- a/drivers/net/e1000/e1000_ethdev.h
+++ b/drivers/net/e1000/e1000_ethdev.h
@@ -522,5 +522,6 @@ int igb_action_rss_same(const struct rte_flow_action_rss *comp,
int igb_config_rss_filter(struct rte_eth_dev *dev,
struct igb_rte_flow_rss_conf *conf,
bool add);
+void igb_flush_desc_rings(struct rte_eth_dev *dev);
#endif /* _E1000_ETHDEV_H_ */
diff --git a/drivers/net/e1000/igb_ethdev.c b/drivers/net/e1000/igb_ethdev.c
index 3ee28cf..8c6a8ea 100644
--- a/drivers/net/e1000/igb_ethdev.c
+++ b/drivers/net/e1000/igb_ethdev.c
@@ -1589,6 +1589,11 @@ eth_igb_close(struct rte_eth_dev *dev)
eth_igb_stop(dev);
adapter->stopped = 1;
+ /* Flush desc rings for i219 */
+ if (hw->mac.type >= e1000_pch_spt) {
+ igb_flush_desc_rings(dev);
+ }
+
e1000_phy_hw_reset(hw);
igb_release_manageability(hw);
igb_hw_control_release(hw);
diff --git a/drivers/net/e1000/igb_rxtx.c b/drivers/net/e1000/igb_rxtx.c
index c5606de..56fc13b 100644
--- a/drivers/net/e1000/igb_rxtx.c
+++ b/drivers/net/e1000/igb_rxtx.c
@@ -2962,3 +2962,92 @@ igb_config_rss_filter(struct rte_eth_dev *dev,
return 0;
}
+
+static void e1000_flush_tx_ring(struct rte_eth_dev *dev)
+{
+ struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data->dev_private);
+ volatile union e1000_adv_tx_desc *tx_desc;
+ uint32_t tdt, tctl, txd_lower = E1000_TXD_CMD_IFCS;
+ uint16_t size = 512;
+ struct igb_tx_queue *txq;
+
+ if (dev->data->tx_queues == NULL)
+ return;
+ txq = dev->data->tx_queues[0];
+
+ tctl = E1000_READ_REG(hw, E1000_TCTL);
+ E1000_WRITE_REG(hw, E1000_TCTL, tctl | E1000_TCTL_EN);
+ tdt = E1000_READ_REG(hw, E1000_TDT(0));
+ if(tdt != txq->tx_tail)
+ return;
+ tx_desc = txq->tx_ring;
+ tx_desc->read.buffer_addr = txq->tx_ring_phys_addr;
+ tx_desc->read.cmd_type_len = rte_cpu_to_le_32(txd_lower | size);
+ tx_desc->read.olinfo_status = 0;
+
+ rte_wmb();
+ txq->tx_tail++;
+ if (txq->tx_tail== txq->nb_tx_desc)
+ txq->tx_tail= 0;
+ rte_io_wmb();
+ E1000_WRITE_REG(hw, E1000_TDT(0), txq->tx_tail);
+ usec_delay(250);
+}
+
+static void e1000_flush_rx_ring(struct rte_eth_dev *dev)
+{
+ uint32_t rctl, rxdctl;
+ struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data->dev_private);
+
+ rctl = E1000_READ_REG(hw, E1000_RCTL);
+ E1000_WRITE_REG(hw, E1000_TCTL, rctl & ~E1000_RCTL_EN);
+ E1000_WRITE_FLUSH(hw);
+ usec_delay(150);
+
+ rxdctl = E1000_READ_REG(hw, E1000_RXDCTL(0));
+ /* zero the lower 14 bits (prefetch and host thresholds) */
+ rxdctl &= 0xffffc000;
+
+ /* update thresholds: prefetch threshold to 31, host threshold to 1
+ * and make sure the granularity is "descriptors" and not "cache lines"
+ */
+ rxdctl |= (0x1F | (1UL << 8) | E1000_RXDCTL_THRESH_UNIT_DESC);
+
+ E1000_WRITE_REG(hw, E1000_RXDCTL(0), rxdctl);
+ /* momentarily enable the RX ring for the changes to take effect */
+ E1000_WRITE_REG(hw, E1000_RCTL, rctl | E1000_RCTL_EN);
+ E1000_WRITE_FLUSH(hw);
+ usec_delay(150);
+ E1000_WRITE_REG(hw, E1000_RCTL, rctl & ~E1000_RCTL_EN);
+}
+
+/**
+ * igb_flush_desc_rings - remove all descriptors from the descriptor rings
+ *
+ * In i219, the descriptor rings must be emptied before resetting/closing the
+ * HW. Failure to do this will cause the HW to enter a unit hang state which
+ * can only be released by PCI reset on the device
+ *
+ */
+
+void igb_flush_desc_rings(struct rte_eth_dev *dev)
+{
+ uint32_t fextnvm11, fextnvm7, tdlen;
+ struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data->dev_private);
+
+ fextnvm11 = E1000_READ_REG(hw, E1000_FEXTNVM11);
+ E1000_WRITE_REG(hw, E1000_FEXTNVM11,
+ fextnvm11 | E1000_FEXTNVM11_DISABLE_MULR_FIX);
+ fextnvm7 = E1000_READ_REG(hw, E1000_FEXTNVM7);
+ tdlen = E1000_READ_REG(hw, E1000_TDLEN(0));
+
+ /* do nothing if we're not in faulty state, or if the queue is empty */
+ if ((fextnvm7 & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) && tdlen) {
+ /* flush desc ring */
+ e1000_flush_tx_ring(dev);
+ fextnvm7 = E1000_READ_REG(hw, E1000_FEXTNVM7);
+ if (fextnvm7 & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) {
+ e1000_flush_rx_ring(dev);
+ }
+ }
+}
--
2.7.4
reply other threads:[~2019-07-04 2:28 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1562239487-34431-1-git-send-email-xiao.zhang@intel.com \
--to=xiao.zhang@intel.com \
--cc=dev@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).