[dpdk-dev] Problem in multi-queue receiving

[dpdk-dev] Problem in multi-queue receiving

[Kai Zhang]

Hi there,

I have a problem for multi-queue receiving.

For a specific application, I am not using the lcore abstractions in DPDK.
I launch rx and tx threads seperately. For one port with N queues, I
launched N rx threads and N tx threads, with each thread in charge of
receiving or sending only one queue.

The tx threads work on their own queues well. However, all received packets
only go to queue 0 rx thread, and other rx threads receive nothing.

My code is at :
https://github.com/kay21s/dpdk/blob/master/examples/pthread/main.c
It has a default NUM_QUEUE=2, which means port 0 is configured with 2
queues, and 2 rx threads and 2 tx threads are launched.
Is there any problem in my implementation? or DPDK does not support it?

Thanks a lot!
Kai

Re: [dpdk-dev] Problem in multi-queue receiving

[Zhang, Helin]

> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Kai Zhang
> Sent: Saturday, August 9, 2014 11:59 PM
> To: dev@dpdk.org
> Subject: [dpdk-dev] Problem in multi-queue receiving
> 
> Hi there,
> 
> I have a problem for multi-queue receiving.
> 
> For a specific application, I am not using the lcore abstractions in DPDK.
> I launch rx and tx threads seperately. For one port with N queues, I launched N
> rx threads and N tx threads, with each thread in charge of receiving or sending
> only one queue.
> 
> The tx threads work on their own queues well. However, all received packets
> only go to queue 0 rx thread, and other rx threads receive nothing.
> 
> My code is at :
> https://github.com/kay21s/dpdk/blob/master/examples/pthread/main.c
> It has a default NUM_QUEUE=2, which means port 0 is configured with 2
> queues, and 2 rx threads and 2 tx threads are launched.
> Is there any problem in my implementation? or DPDK does not support it?
> 
> Thanks a lot!
> Kai

Hi Kai

My suggestion is to try DPDK example applications (e.g. testpmd, l2fwd, l3fwd) first to see if it work fine on you board. Then check the difference between your application and the examples.

Regards,
Helin

Re: [dpdk-dev] Problem in multi-queue receiving

[Stephen Hemminger]

On Sat, 9 Aug 2014 11:59:24 -0400
Kai Zhang <zhang.4522@osu.edu> wrote:

> Hi there,
> 
> I have a problem for multi-queue receiving.
> 
> For a specific application, I am not using the lcore abstractions in DPDK.
> I launch rx and tx threads seperately. For one port with N queues, I
> launched N rx threads and N tx threads, with each thread in charge of
> receiving or sending only one queue.
> 
> The tx threads work on their own queues well. However, all received packets
> only go to queue 0 rx thread, and other rx threads receive nothing.
> 
> My code is at :
> https://github.com/kay21s/dpdk/blob/master/examples/pthread/main.c
> It has a default NUM_QUEUE=2, which means port 0 is configured with 2
> queues, and 2 rx threads and 2 tx threads are launched.
> Is there any problem in my implementation? or DPDK does not support it?
> 
> Thanks a lot!
> Kai

You aren't rxmode.mq_mode therefore you are getting the default value
of 0 == ETH_MQ_RX_NONE. You should set it to ETH_MQ_RX_RSS to enable
RSS mode.

Re: [dpdk-dev] Problem in multi-queue receiving

[Kai Zhang]

Thanks, Stephen. That's the problem.


On Sun, Aug 10, 2014 at 2:11 PM, Stephen Hemminger <
stephen@networkplumber.org> wrote:

> On Sat, 9 Aug 2014 11:59:24 -0400
> Kai Zhang <zhang.4522@osu.edu> wrote:
>
> > Hi there,
> >
> > I have a problem for multi-queue receiving.
> >
> > For a specific application, I am not using the lcore abstractions in
> DPDK.
> > I launch rx and tx threads seperately. For one port with N queues, I
> > launched N rx threads and N tx threads, with each thread in charge of
> > receiving or sending only one queue.
> >
> > The tx threads work on their own queues well. However, all received
> packets
> > only go to queue 0 rx thread, and other rx threads receive nothing.
> >
> > My code is at :
> > https://github.com/kay21s/dpdk/blob/master/examples/pthread/main.c
> > It has a default NUM_QUEUE=2, which means port 0 is configured with 2
> > queues, and 2 rx threads and 2 tx threads are launched.
> > Is there any problem in my implementation? or DPDK does not support it?
> >
> > Thanks a lot!
> > Kai
>
> You aren't rxmode.mq_mode therefore you are getting the default value
> of 0 == ETH_MQ_RX_NONE. You should set it to ETH_MQ_RX_RSS to enable
> RSS mode.
>