* [dpdk-dev] [PATCH 3/3] net/bnxt: update HWRM API to 1.8.2
2017-10-12 17:35 [dpdk-dev] [PATCH 0/3] patchset for bnxt PMD Ajit Khaparde
2017-10-12 17:35 ` [dpdk-dev] [PATCH 1/3] net/bnxt: handle Rx multi queue creation properly Ajit Khaparde
2017-10-12 17:35 ` [dpdk-dev] [PATCH 2/3] net/bnxt: remove redundant code parsing pool_map Ajit Khaparde
@ 2017-10-12 17:35 ` Ajit Khaparde
2017-10-20 19:28 ` Ferruh Yigit
2017-10-20 19:39 ` Ferruh Yigit
2 siblings, 2 replies; 24+ messages in thread
From: Ajit Khaparde @ 2017-10-12 17:35 UTC (permalink / raw)
To: dev; +Cc: ferruh.yigit
This patch updates the HWRM APi to version 1.8.2
This patch is based on an autogenerated file.
Almost all the changes in the PMD are macro name changes.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
---
drivers/net/bnxt/bnxt.h | 2 -
drivers/net/bnxt/bnxt_ethdev.c | 2 +-
drivers/net/bnxt/bnxt_hwrm.c | 2 +-
drivers/net/bnxt/bnxt_hwrm.h | 2 +
drivers/net/bnxt/bnxt_irq.c | 2 +-
drivers/net/bnxt/bnxt_rxr.c | 4 +-
drivers/net/bnxt/bnxt_txr.c | 2 +-
drivers/net/bnxt/hsi_struct_def_dpdk.h | 30829 ++++++++++++++++++++++++-------
8 files changed, 24374 insertions(+), 6471 deletions(-)
diff --git a/drivers/net/bnxt/bnxt.h b/drivers/net/bnxt/bnxt.h
index 294a17466..7f566e4f9 100644
--- a/drivers/net/bnxt/bnxt.h
+++ b/drivers/net/bnxt/bnxt.h
@@ -274,8 +274,6 @@ struct bnxt {
int bnxt_link_update_op(struct rte_eth_dev *eth_dev, int wait_to_complete);
int bnxt_rcv_msg_from_vf(struct bnxt *bp, uint16_t vf_id, void *msg);
-#define RX_PROD_AGG_BD_TYPE_RX_PROD_AGG 0x6
-
bool is_bnxt_supported(struct rte_eth_dev *dev);
extern const struct rte_flow_ops bnxt_flow_ops;
#endif
diff --git a/drivers/net/bnxt/bnxt_ethdev.c b/drivers/net/bnxt/bnxt_ethdev.c
index af7a126bc..e55c08899 100644
--- a/drivers/net/bnxt/bnxt_ethdev.c
+++ b/drivers/net/bnxt/bnxt_ethdev.c
@@ -1609,7 +1609,7 @@ bnxt_rx_queue_count_op(struct rte_eth_dev *dev, uint16_t rx_queue_id)
goto nothing_to_do;
valid = FLIP_VALID(cons, cpr->cp_ring_struct->ring_mask, valid);
cmp_type = CMP_TYPE(rxcmp);
- if (cmp_type == RX_PKT_CMPL_TYPE_RX_L2_TPA_END) {
+ if (cmp_type == RX_TPA_END_CMPL_TYPE_RX_TPA_END) {
cmp = (rte_le_to_cpu_32(
((struct rx_tpa_end_cmpl *)
(rxcmp))->agg_bufs_v1) &
diff --git a/drivers/net/bnxt/bnxt_hwrm.c b/drivers/net/bnxt/bnxt_hwrm.c
index c9b04e248..587e778cf 100644
--- a/drivers/net/bnxt/bnxt_hwrm.c
+++ b/drivers/net/bnxt/bnxt_hwrm.c
@@ -785,7 +785,7 @@ static int bnxt_hwrm_port_phy_qcfg(struct bnxt *bp,
(link_info->phy_link_status ==
HWRM_PORT_PHY_QCFG_OUTPUT_LINK_LINK) ? 1 : 0;
link_info->link_speed = rte_le_to_cpu_16(resp->link_speed);
- link_info->duplex = resp->duplex;
+ link_info->duplex = resp->duplex_cfg;
link_info->pause = resp->pause;
link_info->auto_pause = resp->auto_pause;
link_info->force_pause = resp->force_pause;
diff --git a/drivers/net/bnxt/bnxt_hwrm.h b/drivers/net/bnxt/bnxt_hwrm.h
index 85083e619..8769cd6f2 100644
--- a/drivers/net/bnxt/bnxt_hwrm.h
+++ b/drivers/net/bnxt/bnxt_hwrm.h
@@ -42,6 +42,8 @@ struct bnxt_filter_info;
struct bnxt_cp_ring_info;
#define HWRM_SEQ_ID_INVALID -1U
+#define HWRM_SHORT_REQ_SIGNATURE_SHORT_CMD \
+ HWRM_SHORT_INPUT_SIGNATURE_SHORT_CMD
int bnxt_hwrm_cfa_l2_clear_rx_mask(struct bnxt *bp,
struct bnxt_vnic_info *vnic);
diff --git a/drivers/net/bnxt/bnxt_irq.c b/drivers/net/bnxt/bnxt_irq.c
index 79a119623..65522b23d 100644
--- a/drivers/net/bnxt/bnxt_irq.c
+++ b/drivers/net/bnxt/bnxt_irq.c
@@ -81,7 +81,7 @@ static void bnxt_int_handler(void *param)
goto no_more;
}
RTE_LOG(INFO, PMD,
- "Ignoring %02x completion\n", CMP_TYPE(cmp));
+ "Ignoring %02lx completion\n", CMP_TYPE(cmp));
break;
}
raw_cons = NEXT_RAW_CMP(raw_cons);
diff --git a/drivers/net/bnxt/bnxt_rxr.c b/drivers/net/bnxt/bnxt_rxr.c
index 153ca93ed..1b667430e 100644
--- a/drivers/net/bnxt/bnxt_rxr.c
+++ b/drivers/net/bnxt/bnxt_rxr.c
@@ -410,12 +410,12 @@ static int bnxt_rx_pkt(struct rte_mbuf **rx_pkt,
cpr->valid);
cmp_type = CMP_TYPE(rxcmp);
- if (cmp_type == RX_PKT_CMPL_TYPE_RX_L2_TPA_START) {
+ if (cmp_type == CMPL_BASE_TYPE_RX_TPA_START) {
bnxt_tpa_start(rxq, (struct rx_tpa_start_cmpl *)rxcmp,
(struct rx_tpa_start_cmpl_hi *)rxcmp1);
rc = -EINVAL; /* Continue w/o new mbuf */
goto next_rx;
- } else if (cmp_type == RX_PKT_CMPL_TYPE_RX_L2_TPA_END) {
+ } else if (cmp_type == CMPL_BASE_TYPE_RX_TPA_END) {
mbuf = bnxt_tpa_end(rxq, &tmp_raw_cons,
(struct rx_tpa_end_cmpl *)rxcmp,
(struct rx_tpa_end_cmpl_hi *)rxcmp1);
diff --git a/drivers/net/bnxt/bnxt_txr.c b/drivers/net/bnxt/bnxt_txr.c
index 8ca4bbd80..ce221a909 100644
--- a/drivers/net/bnxt/bnxt_txr.c
+++ b/drivers/net/bnxt/bnxt_txr.c
@@ -321,7 +321,7 @@ static int bnxt_handle_tx_cp(struct bnxt_tx_queue *txq)
nb_tx_pkts++;
else
RTE_LOG_DP(DEBUG, PMD,
- "Unhandled CMP type %02x\n",
+ "Unhandled CMP type %02lx\n",
CMP_TYPE(txcmp));
raw_cons = NEXT_RAW_CMP(raw_cons);
}
diff --git a/drivers/net/bnxt/hsi_struct_def_dpdk.h b/drivers/net/bnxt/hsi_struct_def_dpdk.h
index 1b35466a9..6173529e8 100644
--- a/drivers/net/bnxt/hsi_struct_def_dpdk.h
+++ b/drivers/net/bnxt/hsi_struct_def_dpdk.h
@@ -1,174 +1,51 @@
-/*-
- * BSD LICENSE
+/****************************************************************************
+ * Copyright(c) 2001-2017 Broadcom Corporation, all rights reserved
+ * Proprietary and Confidential Information.
*
- * Copyright(c) 2001-2017 Broadcom Limited.
- * All rights reserved.
+ * This source file is the property of Broadcom Corporation, and
+ * may not be copied or distributed in any isomorphic form without
+ * the prior written consent of Broadcom Corporation.
*
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
+ * Name: hsi_struct_def_linux_external.h
*
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in
- * the documentation and/or other materials provided with the
- * distribution.
- * * Neither the name of Broadcom Corporation nor the names of its
- * contributors may be used to endorse or promote products derived
- * from this software without specific prior written permission.
+ * Description: Definition of HSI data structures
*
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-#ifndef _HSI_STRUCT_DEF_DPDK_
-#define _HSI_STRUCT_DEF_DPDK_
-/* HSI and HWRM Specification 1.7.7 */
+ * Date: 10/11/17 17:40:02
+ *
+ * Note: This file is scripted generated by hsi_decode.py.
+ * DO NOT modify this file manually !!!!
+ *
+ ****************************************************************************/
+#ifndef _HSI_STRUCT_DEF_DPDK_H_
+#define _HSI_STRUCT_DEF_DPDK_H_
+/* HSI and HWRM Specification 1.8.2 */
#define HWRM_VERSION_MAJOR 1
-#define HWRM_VERSION_MINOR 7
-#define HWRM_VERSION_UPDATE 7
+#define HWRM_VERSION_MINOR 8
+#define HWRM_VERSION_UPDATE 2
-#define HWRM_VERSION_STR "1.7.7"
+#define HWRM_VERSION_RSVD 0 /* non-zero means beta version */
+
+#define HWRM_VERSION_STR "1.8.2.0"
/*
* Following is the signature for HWRM message field that indicates not
- * applicable (All F's). Need to cast it the size of the field if needed.
+ * applicable (All F's). Need to cast it the size of the field if needed.
*/
#define HWRM_NA_SIGNATURE ((uint32_t)(-1))
-#define HWRM_MAX_REQ_LEN (128) /* hwrm_func_buf_rgtr */
-#define HWRM_MAX_RESP_LEN (248) /* hwrm_selftest_qlist */
-#define HW_HASH_INDEX_SIZE 0x80 /* 7 bit indirection table index. */
+#define HWRM_MAX_REQ_LEN (128) /* hwrm_func_buf_rgtr */
+#define HWRM_MAX_RESP_LEN (280) /* hwrm_selftest_qlist */
+#define HW_HASH_INDEX_SIZE 0x80 /* 7 bit indirection table index. */
#define HW_HASH_KEY_SIZE 40
-#define HWRM_RESP_VALID_KEY 1 /* valid key for HWRM response */
+#define HWRM_RESP_VALID_KEY 1 /* valid key for HWRM response */
#define HWRM_ROCE_SP_HSI_VERSION_MAJOR 1
-#define HWRM_ROCE_SP_HSI_VERSION_MINOR 7
-#define HWRM_ROCE_SP_HSI_VERSION_UPDATE 4
+#define HWRM_ROCE_SP_HSI_VERSION_MINOR 8
+#define HWRM_ROCE_SP_HSI_VERSION_UPDATE 2
+#define HWRM_ROCE_SP_HSI_VERSION_STR "1.8.2"
/*
- * Request types
+ * Following is the signature for ROCE_SP_HSI message field that indicates not
+ * applicable (All F's). Need to cast it the size of the field if needed.
*/
-#define HWRM_VER_GET (UINT32_C(0x0))
-#define HWRM_FUNC_BUF_UNRGTR (UINT32_C(0xe))
-#define HWRM_FUNC_VF_CFG (UINT32_C(0xf))
- /* Reserved for future use */
-#define RESERVED1 (UINT32_C(0x10))
-#define HWRM_FUNC_RESET (UINT32_C(0x11))
-#define HWRM_FUNC_GETFID (UINT32_C(0x12))
-#define HWRM_FUNC_VF_ALLOC (UINT32_C(0x13))
-#define HWRM_FUNC_VF_FREE (UINT32_C(0x14))
-#define HWRM_FUNC_QCAPS (UINT32_C(0x15))
-#define HWRM_FUNC_QCFG (UINT32_C(0x16))
-#define HWRM_FUNC_CFG (UINT32_C(0x17))
-#define HWRM_FUNC_QSTATS (UINT32_C(0x18))
-#define HWRM_FUNC_CLR_STATS (UINT32_C(0x19))
-#define HWRM_FUNC_DRV_UNRGTR (UINT32_C(0x1a))
-#define HWRM_FUNC_VF_RESC_FREE (UINT32_C(0x1b))
-#define HWRM_FUNC_VF_VNIC_IDS_QUERY (UINT32_C(0x1c))
-#define HWRM_FUNC_DRV_RGTR (UINT32_C(0x1d))
-#define HWRM_FUNC_DRV_QVER (UINT32_C(0x1e))
-#define HWRM_FUNC_BUF_RGTR (UINT32_C(0x1f))
-#define HWRM_PORT_PHY_CFG (UINT32_C(0x20))
-#define HWRM_PORT_MAC_CFG (UINT32_C(0x21))
-#define HWRM_PORT_QSTATS (UINT32_C(0x23))
-#define HWRM_PORT_LPBK_QSTATS (UINT32_C(0x24))
-#define HWRM_PORT_CLR_STATS (UINT32_C(0x25))
-#define HWRM_PORT_PHY_QCFG (UINT32_C(0x27))
-#define HWRM_PORT_MAC_QCFG (UINT32_C(0x28))
-#define HWRM_PORT_PHY_QCAPS (UINT32_C(0x2a))
-#define HWRM_PORT_LED_CFG (UINT32_C(0x2d))
-#define HWRM_PORT_LED_QCFG (UINT32_C(0x2e))
-#define HWRM_PORT_LED_QCAPS (UINT32_C(0x2f))
-#define HWRM_QUEUE_QPORTCFG (UINT32_C(0x30))
-#define HWRM_QUEUE_QCFG (UINT32_C(0x31))
-#define HWRM_QUEUE_CFG (UINT32_C(0x32))
-#define HWRM_FUNC_VLAN_CFG (UINT32_C(0x33))
-#define HWRM_FUNC_VLAN_QCFG (UINT32_C(0x34))
-#define HWRM_QUEUE_PFCENABLE_QCFG (UINT32_C(0x35))
-#define HWRM_QUEUE_PFCENABLE_CFG (UINT32_C(0x36))
-#define HWRM_QUEUE_PRI2COS_QCFG (UINT32_C(0x37))
-#define HWRM_QUEUE_PRI2COS_CFG (UINT32_C(0x38))
-#define HWRM_QUEUE_COS2BW_QCFG (UINT32_C(0x39))
-#define HWRM_QUEUE_COS2BW_CFG (UINT32_C(0x3a))
-#define HWRM_VNIC_ALLOC (UINT32_C(0x40))
-#define HWRM_VNIC_ALLOC (UINT32_C(0x40))
-#define HWRM_VNIC_FREE (UINT32_C(0x41))
-#define HWRM_VNIC_CFG (UINT32_C(0x42))
-#define HWRM_VNIC_QCFG (UINT32_C(0x43))
-#define HWRM_VNIC_TPA_CFG (UINT32_C(0x44))
-#define HWRM_VNIC_RSS_CFG (UINT32_C(0x46))
-#define HWRM_VNIC_RSS_QCFG (UINT32_C(0x47))
-#define HWRM_VNIC_PLCMODES_CFG (UINT32_C(0x48))
-#define HWRM_VNIC_PLCMODES_QCFG (UINT32_C(0x49))
-#define HWRM_VNIC_QCAPS (UINT32_C(0x4a))
-#define HWRM_RING_ALLOC (UINT32_C(0x50))
-#define HWRM_RING_FREE (UINT32_C(0x51))
-#define HWRM_RING_CMPL_RING_QAGGINT_PARAMS (UINT32_C(0x52))
-#define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS (UINT32_C(0x53))
-#define HWRM_RING_RESET (UINT32_C(0x5e))
-#define HWRM_RING_GRP_ALLOC (UINT32_C(0x60))
-#define HWRM_RING_GRP_FREE (UINT32_C(0x61))
-#define HWRM_VNIC_RSS_COS_LB_CTX_ALLOC (UINT32_C(0x70))
-#define HWRM_VNIC_RSS_COS_LB_CTX_FREE (UINT32_C(0x71))
-#define HWRM_CFA_L2_FILTER_ALLOC (UINT32_C(0x90))
-#define HWRM_CFA_L2_FILTER_FREE (UINT32_C(0x91))
-#define HWRM_CFA_L2_FILTER_CFG (UINT32_C(0x92))
-#define HWRM_CFA_L2_SET_RX_MASK (UINT32_C(0x93))
- /* Reserved for future use */
-#define HWRM_CFA_VLAN_ANTISPOOF_CFG (UINT32_C(0x94))
-#define HWRM_CFA_TUNNEL_FILTER_ALLOC (UINT32_C(0x95))
-#define HWRM_CFA_TUNNEL_FILTER_FREE (UINT32_C(0x96))
-#define HWRM_CFA_NTUPLE_FILTER_ALLOC (UINT32_C(0x99))
-#define HWRM_CFA_NTUPLE_FILTER_FREE (UINT32_C(0x9a))
-#define HWRM_CFA_NTUPLE_FILTER_CFG (UINT32_C(0x9b))
-#define HWRM_CFA_EM_FLOW_ALLOC (UINT32_C(0x9c))
-#define HWRM_CFA_EM_FLOW_FREE (UINT32_C(0x9d))
-#define HWRM_CFA_EM_FLOW_CFG (UINT32_C(0x9e))
-#define HWRM_TUNNEL_DST_PORT_QUERY (UINT32_C(0xa0))
-#define HWRM_TUNNEL_DST_PORT_ALLOC (UINT32_C(0xa1))
-#define HWRM_TUNNEL_DST_PORT_FREE (UINT32_C(0xa2))
-#define HWRM_STAT_CTX_ALLOC (UINT32_C(0xb0))
-#define HWRM_STAT_CTX_FREE (UINT32_C(0xb1))
-#define HWRM_STAT_CTX_QUERY (UINT32_C(0xb2))
-#define HWRM_STAT_CTX_CLR_STATS (UINT32_C(0xb3))
-#define HWRM_FW_RESET (UINT32_C(0xc0))
-#define HWRM_FW_QSTATUS (UINT32_C(0xc1))
-#define HWRM_EXEC_FWD_RESP (UINT32_C(0xd0))
-#define HWRM_REJECT_FWD_RESP (UINT32_C(0xd1))
-#define HWRM_FWD_RESP (UINT32_C(0xd2))
-#define HWRM_FWD_ASYNC_EVENT_CMPL (UINT32_C(0xd3))
-#define HWRM_TEMP_MONITOR_QUERY (UINT32_C(0xe0))
-#define HWRM_WOL_FILTER_ALLOC (UINT32_C(0xf0))
-#define HWRM_WOL_FILTER_FREE (UINT32_C(0xf1))
-#define HWRM_WOL_FILTER_QCFG (UINT32_C(0xf2))
-#define HWRM_WOL_REASON_QCFG (UINT32_C(0xf3))
-#define HWRM_DBG_DUMP (UINT32_C(0xff14))
-#define HWRM_NVM_VALIDATE_OPTION (UINT32_C(0xffef))
-#define HWRM_NVM_FLUSH (UINT32_C(0xfff0))
-#define HWRM_NVM_GET_VARIABLE (UINT32_C(0xfff1))
-#define HWRM_NVM_SET_VARIABLE (UINT32_C(0xfff2))
-#define HWRM_NVM_INSTALL_UPDATE (UINT32_C(0xfff3))
-#define HWRM_NVM_MODIFY (UINT32_C(0xfff4))
-#define HWRM_NVM_VERIFY_UPDATE (UINT32_C(0xfff5))
-#define HWRM_NVM_GET_DEV_INFO (UINT32_C(0xfff6))
-#define HWRM_NVM_ERASE_DIR_ENTRY (UINT32_C(0xfff7))
-#define HWRM_NVM_MOD_DIR_ENTRY (UINT32_C(0xfff8))
-#define HWRM_NVM_FIND_DIR_ENTRY (UINT32_C(0xfff9))
-#define HWRM_NVM_GET_DIR_ENTRIES (UINT32_C(0xfffa))
-#define HWRM_NVM_GET_DIR_INFO (UINT32_C(0xfffb))
-#define HWRM_NVM_RAW_DUMP (UINT32_C(0xfffc))
-#define HWRM_NVM_READ (UINT32_C(0xfffd))
-#define HWRM_NVM_WRITE (UINT32_C(0xfffe))
-#define HWRM_NVM_RAW_WRITE_BLK (UINT32_C(0xffff))
-
+#define HWRM_ROCE_SP_HSI_NA_SIGNATURE ((uint32_t)(-1))
/*
* Note: The Host Software Interface (HSI) and Hardware Resource Manager (HWRM)
* specification describes the data structures used in Ethernet packet or RDMA
@@ -189,7 +66,51 @@
* host. RX Rings that have aggregation buffers are known as aggregation rings
* and must contain only aggregation buffers.
*/
-/* Short TX BD (16 bytes) */
+/*
+ * Note: BD Ring structures are written by the driver to TX Rings and RX Rings
+ * to indicate to the chip there is more buffer space in the host that needs to
+ * be transmitted or is available for receive data.
+ */
+/* BD Base (8 bytes) */
+struct bd_base {
+ uint8_t type;
+ /* This value identifies the type of buffer descriptor. */
+ #define HWRM_BD_BASE_TYPE_MASK 0x3fUL
+ #define HWRM_BD_BASE_TYPE_SFT 0
+ /*
+ * Indicates that this BD is 16B long and is
+ * used for normal L2 packet transmission.
+ */
+ #define HWRM_BD_BASE_TYPE_TX_BD_SHORT 0x0UL
+ /*
+ * Indicates that this BD is 1BB long and is an
+ * empty TX BD. Not valid for use by the driver.
+ */
+ #define HWRM_BD_BASE_TYPE_TX_BD_EMPTY 0x1UL
+ /*
+ * Indicates that this BD is 16B long and is an
+ * RX Producer (ie. empty) buffer descriptor.
+ */
+ #define HWRM_BD_BASE_TYPE_RX_PROD_PKT 0x4UL
+ /*
+ * Indicates that this BD is 16B long and is an
+ * RX Producer Buffer BD.
+ */
+ #define HWRM_BD_BASE_TYPE_RX_PROD_BFR 0x5UL
+ /*
+ * Indicates that this BD is 16B long and is an
+ * RX Producer Assembly Buffer Descriptor.
+ */
+ #define HWRM_BD_BASE_TYPE_RX_PROD_AGG 0x6UL
+ /*
+ * Indicates that this BD is 32B long and is
+ * used for normal L2 packet transmission.
+ */
+ #define HWRM_BD_BASE_TYPE_TX_BD_LONG 0x10UL
+ uint8_t unused_1[7];
+} __attribute__((packed));
+
+/* Short TX BD (16 bytes) */
struct tx_bd_short {
uint16_t flags_type;
/*
@@ -198,19 +119,19 @@ struct tx_bd_short {
* remaining BDs of a packet.
*/
/* This value identifies the type of buffer descriptor. */
- #define TX_BD_SHORT_TYPE_MASK UINT32_C(0x3f)
- #define TX_BD_SHORT_TYPE_SFT 0
+ #define TX_BD_SHORT_TYPE_MASK 0x3fUL
+ #define TX_BD_SHORT_TYPE_SFT 0
/*
* Indicates that this BD is 16B long and is
* used for normal L2 packet transmission.
*/
- #define TX_BD_SHORT_TYPE_TX_BD_SHORT UINT32_C(0x0)
+ #define TX_BD_SHORT_TYPE_TX_BD_SHORT 0x0UL
/*
* If set to 1, the packet ends with the data in the buffer
* pointed to by this descriptor. This flag must be valid on
* every BD.
*/
- #define TX_BD_SHORT_FLAGS_PACKET_END UINT32_C(0x40)
+ #define TX_BD_SHORT_FLAGS_PACKET_END 0x40UL
/*
* If set to 1, the device will not generate a completion for
* this transmit packet unless there is an error in it's
@@ -218,36 +139,36 @@ struct tx_bd_short {
* completed normally. This bit must be valid only on the first
* BD of a packet.
*/
- #define TX_BD_SHORT_FLAGS_NO_CMPL UINT32_C(0x80)
+ #define TX_BD_SHORT_FLAGS_NO_CMPL 0x80UL
/*
* This value indicates how many 16B BD locations are consumed
* in the ring by this packet. A value of 1 indicates that this
- * BD is the only BD (and that the it is a short BD). A value of
+ * BD is the only BD (and that the it is a short BD). A value of
* 3 indicates either 3 short BDs or 1 long BD and one short BD
* in the packet. A value of 0 indicates that there are 32 BD
- * locations in the packet (the maximum). This field is valid
+ * locations in the packet (the maximum). This field is valid
* only on the first BD of a packet.
*/
- #define TX_BD_SHORT_FLAGS_BD_CNT_MASK UINT32_C(0x1f00)
- #define TX_BD_SHORT_FLAGS_BD_CNT_SFT 8
+ #define TX_BD_SHORT_FLAGS_BD_CNT_MASK 0x1f00UL
+ #define TX_BD_SHORT_FLAGS_BD_CNT_SFT 8
/*
* This value is a hint for the length of the entire packet. It
* is used by the chip to optimize internal processing. The
* packet will be dropped if the hint is too short. This field
* is valid only on the first BD of a packet.
*/
- #define TX_BD_SHORT_FLAGS_LHINT_MASK UINT32_C(0x6000)
- #define TX_BD_SHORT_FLAGS_LHINT_SFT 13
+ #define TX_BD_SHORT_FLAGS_LHINT_MASK 0x6000UL
+ #define TX_BD_SHORT_FLAGS_LHINT_SFT 13
/* indicates packet length < 512B */
- #define TX_BD_SHORT_FLAGS_LHINT_LT512 (UINT32_C(0x0) << 13)
+ #define TX_BD_SHORT_FLAGS_LHINT_LT512 (0x0UL << 13)
/* indicates 512 <= packet length < 1KB */
- #define TX_BD_SHORT_FLAGS_LHINT_LT1K (UINT32_C(0x1) << 13)
+ #define TX_BD_SHORT_FLAGS_LHINT_LT1K (0x1UL << 13)
/* indicates 1KB <= packet length < 2KB */
- #define TX_BD_SHORT_FLAGS_LHINT_LT2K (UINT32_C(0x2) << 13)
+ #define TX_BD_SHORT_FLAGS_LHINT_LT2K (0x2UL << 13)
/* indicates packet length >= 2KB */
- #define TX_BD_SHORT_FLAGS_LHINT_GTE2K (UINT32_C(0x3) << 13)
+ #define TX_BD_SHORT_FLAGS_LHINT_GTE2K (0x3UL << 13)
#define TX_BD_SHORT_FLAGS_LHINT_LAST \
- TX_BD_SHORT_FLAGS_LHINT_GTE2K
+ TX_BD_SHORT_FLAGS_LHINT_GTE2K
/*
* If set to 1, the device immediately updates the Send Consumer
* Index after the buffer associated with this descriptor has
@@ -258,14 +179,14 @@ struct tx_bd_short {
* the host interrupt coalescing conditions has been met. This
* bit must be valid on the first BD of a packet.
*/
- #define TX_BD_SHORT_FLAGS_COAL_NOW UINT32_C(0x8000)
+ #define TX_BD_SHORT_FLAGS_COAL_NOW 0x8000UL
/*
* All bits in this field must be valid on the first BD of a
* packet. Only the packet_end bit must be valid for the
* remaining BDs of a packet.
*/
- #define TX_BD_SHORT_FLAGS_MASK UINT32_C(0xffc0)
- #define TX_BD_SHORT_FLAGS_SFT 6
+ #define TX_BD_SHORT_FLAGS_MASK 0xffc0UL
+ #define TX_BD_SHORT_FLAGS_SFT 6
uint16_t len;
/*
* This is the length of the host physical buffer this BD
@@ -287,7 +208,7 @@ struct tx_bd_short {
*/
} __attribute__((packed));
-/* Long TX BD (32 bytes split to 2 16-byte struct) */
+/* Long TX BD (32 bytes split to 2 16-byte struct) */
struct tx_bd_long {
uint16_t flags_type;
/*
@@ -296,19 +217,19 @@ struct tx_bd_long {
* remaining BDs of a packet.
*/
/* This value identifies the type of buffer descriptor. */
- #define TX_BD_LONG_TYPE_MASK UINT32_C(0x3f)
- #define TX_BD_LONG_TYPE_SFT 0
+ #define TX_BD_LONG_TYPE_MASK 0x3fUL
+ #define TX_BD_LONG_TYPE_SFT 0
/*
* Indicates that this BD is 32B long and is
* used for normal L2 packet transmission.
*/
- #define TX_BD_LONG_TYPE_TX_BD_LONG UINT32_C(0x10)
+ #define TX_BD_LONG_TYPE_TX_BD_LONG 0x10UL
/*
* If set to 1, the packet ends with the data in the buffer
* pointed to by this descriptor. This flag must be valid on
* every BD.
*/
- #define TX_BD_LONG_FLAGS_PACKET_END UINT32_C(0x40)
+ #define TX_BD_LONG_FLAGS_PACKET_END 0x40UL
/*
* If set to 1, the device will not generate a completion for
* this transmit packet unless there is an error in it's
@@ -316,36 +237,36 @@ struct tx_bd_long {
* completed normally. This bit must be valid only on the first
* BD of a packet.
*/
- #define TX_BD_LONG_FLAGS_NO_CMPL UINT32_C(0x80)
+ #define TX_BD_LONG_FLAGS_NO_CMPL 0x80UL
/*
* This value indicates how many 16B BD locations are consumed
* in the ring by this packet. A value of 1 indicates that this
- * BD is the only BD (and that the it is a short BD). A value of
+ * BD is the only BD (and that the it is a short BD). A value of
* 3 indicates either 3 short BDs or 1 long BD and one short BD
* in the packet. A value of 0 indicates that there are 32 BD
- * locations in the packet (the maximum). This field is valid
+ * locations in the packet (the maximum). This field is valid
* only on the first BD of a packet.
*/
- #define TX_BD_LONG_FLAGS_BD_CNT_MASK UINT32_C(0x1f00)
- #define TX_BD_LONG_FLAGS_BD_CNT_SFT 8
+ #define TX_BD_LONG_FLAGS_BD_CNT_MASK 0x1f00UL
+ #define TX_BD_LONG_FLAGS_BD_CNT_SFT 8
/*
* This value is a hint for the length of the entire packet. It
* is used by the chip to optimize internal processing. The
* packet will be dropped if the hint is too short. This field
* is valid only on the first BD of a packet.
*/
- #define TX_BD_LONG_FLAGS_LHINT_MASK UINT32_C(0x6000)
- #define TX_BD_LONG_FLAGS_LHINT_SFT 13
+ #define TX_BD_LONG_FLAGS_LHINT_MASK 0x6000UL
+ #define TX_BD_LONG_FLAGS_LHINT_SFT 13
/* indicates packet length < 512B */
- #define TX_BD_LONG_FLAGS_LHINT_LT512 (UINT32_C(0x0) << 13)
+ #define TX_BD_LONG_FLAGS_LHINT_LT512 (0x0UL << 13)
/* indicates 512 <= packet length < 1KB */
- #define TX_BD_LONG_FLAGS_LHINT_LT1K (UINT32_C(0x1) << 13)
+ #define TX_BD_LONG_FLAGS_LHINT_LT1K (0x1UL << 13)
/* indicates 1KB <= packet length < 2KB */
- #define TX_BD_LONG_FLAGS_LHINT_LT2K (UINT32_C(0x2) << 13)
+ #define TX_BD_LONG_FLAGS_LHINT_LT2K (0x2UL << 13)
/* indicates packet length >= 2KB */
- #define TX_BD_LONG_FLAGS_LHINT_GTE2K (UINT32_C(0x3) << 13)
+ #define TX_BD_LONG_FLAGS_LHINT_GTE2K (0x3UL << 13)
#define TX_BD_LONG_FLAGS_LHINT_LAST \
- TX_BD_LONG_FLAGS_LHINT_GTE2K
+ TX_BD_LONG_FLAGS_LHINT_GTE2K
/*
* If set to 1, the device immediately updates the Send Consumer
* Index after the buffer associated with this descriptor has
@@ -356,14 +277,14 @@ struct tx_bd_long {
* the host interrupt coalescing conditions has been met. This
* bit must be valid on the first BD of a packet.
*/
- #define TX_BD_LONG_FLAGS_COAL_NOW UINT32_C(0x8000)
+ #define TX_BD_LONG_FLAGS_COAL_NOW 0x8000UL
/*
* All bits in this field must be valid on the first BD of a
* packet. Only the packet_end bit must be valid for the
* remaining BDs of a packet.
*/
- #define TX_BD_LONG_FLAGS_MASK UINT32_C(0xffc0)
- #define TX_BD_LONG_FLAGS_SFT 6
+ #define TX_BD_LONG_FLAGS_MASK 0xffc0UL
+ #define TX_BD_LONG_FLAGS_SFT 6
uint16_t len;
/*
* This is the length of the host physical buffer this BD
@@ -402,7 +323,7 @@ struct tx_bd_long_hi {
* LSO flag is set. This bit must be valid on the first BD of a
* packet.
*/
- #define TX_BD_LONG_LFLAGS_TCP_UDP_CHKSUM UINT32_C(0x1)
+ #define TX_BD_LONG_LFLAGS_TCP_UDP_CHKSUM 0x1UL
/*
* If set to 1, the controller replaces the IP checksum of the
* normal packets, or the inner IP checksum of the encapsulated
@@ -410,7 +331,7 @@ struct tx_bd_long_hi {
* packet associated with this descriptor. This bit must be
* valid on the first BD of a packet.
*/
- #define TX_BD_LONG_LFLAGS_IP_CHKSUM UINT32_C(0x2)
+ #define TX_BD_LONG_LFLAGS_IP_CHKSUM 0x2UL
/*
* If set to 1, the controller will not append an Ethernet CRC
* to the end of the frame. This bit must be valid on the first
@@ -419,13 +340,13 @@ struct tx_bd_long_hi {
* offload such as CSO or LSO. The intent is that the packet
* from the host already has a valid Ethernet CRC on the packet.
*/
- #define TX_BD_LONG_LFLAGS_NOCRC UINT32_C(0x4)
+ #define TX_BD_LONG_LFLAGS_NOCRC 0x4UL
/*
* If set to 1, the device will record the time at which the
* packet was actually transmitted at the TX MAC. This bit must
* be valid on the first BD of a packet.
*/
- #define TX_BD_LONG_LFLAGS_STAMP UINT32_C(0x8)
+ #define TX_BD_LONG_LFLAGS_STAMP 0x8UL
/*
* If set to 1, The controller replaces the tunnel IP checksum
* field with hardware calculated IP checksum for the IP header
@@ -435,13 +356,13 @@ struct tx_bd_long_hi {
* bit is set, outer UDP checksum will be calculated for the
* following cases: 1. Packets with tcp_udp_chksum flag set to
* offload checksum for inner packet AND the inner packet is
- * TCP/UDP. If the inner packet is ICMP for example (non-
+ * TCP/UDP. If the inner packet is ICMP for example (non-
* TCP/UDP), even if the tcp_udp_chksum is set, the outer UDP
* checksum will not be calculated. 2. Packets with lso flag set
* which implies inner TCP checksum calculation as part of LSO
* operation.
*/
- #define TX_BD_LONG_LFLAGS_T_IP_CHKSUM UINT32_C(0x10)
+ #define TX_BD_LONG_LFLAGS_T_IP_CHKSUM 0x10UL
/*
* If set to 1, the device will treat this packet with LSO(Large
* Send Offload) processing for both normal or encapsulated
@@ -452,7 +373,7 @@ struct tx_bd_long_hi {
* appropriate checksum fields for segmented packets. When this
* bit is 1, the hdr_size and mss fields must be valid.
*/
- #define TX_BD_LONG_LFLAGS_LSO UINT32_C(0x20)
+ #define TX_BD_LONG_LFLAGS_LSO 0x20UL
/*
* If set to zero when LSO is '1', then the IPID will be treated
* as a 16b number and will be wrapped if it exceeds a value of
@@ -460,26 +381,26 @@ struct tx_bd_long_hi {
* treated as a 15b number and will be wrapped if it exceeds a
* value 0f 0x7fff.
*/
- #define TX_BD_LONG_LFLAGS_IPID_FMT UINT32_C(0x40)
+ #define TX_BD_LONG_LFLAGS_IPID_FMT 0x40UL
/*
* If set to zero when LSO is '1', then the IPID of the tunnel
* IP header will not be modified during LSO operations. If set
* to one when LSO is '1', then the IPID of the tunnel IP header
* will be incremented for each subsequent segment of an LSO
* operation. The flag is ignored if the LSO packet is a normal
- * (non-tunneled) TCP packet.
+ * (non-tunneled) TCP packet.
*/
- #define TX_BD_LONG_LFLAGS_T_IPID UINT32_C(0x80)
+ #define TX_BD_LONG_LFLAGS_T_IPID 0x80UL
/*
* If set to '1', then the RoCE ICRC will be appended to the
* packet. Packet must be a valid RoCE format packet.
*/
- #define TX_BD_LONG_LFLAGS_ROCE_CRC UINT32_C(0x100)
+ #define TX_BD_LONG_LFLAGS_ROCE_CRC 0x100UL
/*
* If set to '1', then the FCoE CRC will be appended to the
* packet. Packet must be a valid FCoE format packet.
*/
- #define TX_BD_LONG_LFLAGS_FCOE_CRC UINT32_C(0x200)
+ #define TX_BD_LONG_LFLAGS_FCOE_CRC 0x200UL
uint16_t hdr_size;
/*
* When LSO is '1', this field must contain the offset of the
@@ -489,8 +410,8 @@ struct tx_bd_long_hi {
* packet as 16-bit words. This value must be valid on the first
* BD of a packet.
*/
- #define TX_BD_LONG_HDR_SIZE_MASK UINT32_C(0x1ff)
- #define TX_BD_LONG_HDR_SIZE_SFT 0
+ #define TX_BD_LONG_HDR_SIZE_MASK 0x1ffUL
+ #define TX_BD_LONG_HDR_SIZE_SFT 0
uint32_t mss;
/*
* This is the MSS value that will be used to do the LSO
@@ -498,8 +419,8 @@ struct tx_bd_long_hi {
* payload for each segment generated by the LSO operation. This
* value must be valid on the first BD of a packet.
*/
- #define TX_BD_LONG_MSS_MASK UINT32_C(0x7fff)
- #define TX_BD_LONG_MSS_SFT 0
+ #define TX_BD_LONG_MSS_MASK 0x7fffUL
+ #define TX_BD_LONG_MSS_SFT 0
uint16_t unused_2;
uint16_t cfa_action;
/*
@@ -513,62 +434,79 @@ struct tx_bd_long_hi {
* operations that are done in addition to any action editing.
*/
/* When key=1, This is the VLAN tag VID value. */
- #define TX_BD_LONG_CFA_META_VLAN_VID_MASK UINT32_C(0xfff)
- #define TX_BD_LONG_CFA_META_VLAN_VID_SFT 0
+ #define TX_BD_LONG_CFA_META_VLAN_VID_MASK 0xfffUL
+ #define TX_BD_LONG_CFA_META_VLAN_VID_SFT 0
/* When key=1, This is the VLAN tag DE value. */
- #define TX_BD_LONG_CFA_META_VLAN_DE UINT32_C(0x1000)
+ #define TX_BD_LONG_CFA_META_VLAN_DE 0x1000UL
/* When key=1, This is the VLAN tag PRI value. */
- #define TX_BD_LONG_CFA_META_VLAN_PRI_MASK UINT32_C(0xe000)
- #define TX_BD_LONG_CFA_META_VLAN_PRI_SFT 13
+ #define TX_BD_LONG_CFA_META_VLAN_PRI_MASK 0xe000UL
+ #define TX_BD_LONG_CFA_META_VLAN_PRI_SFT 13
/* When key=1, This is the VLAN tag TPID select value. */
- #define TX_BD_LONG_CFA_META_VLAN_TPID_MASK UINT32_C(0x70000)
- #define TX_BD_LONG_CFA_META_VLAN_TPID_SFT 16
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_MASK 0x70000UL
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_SFT 16
/* 0x88a8 */
- #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID88A8 (UINT32_C(0x0) << 16)
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID88A8 (0x0UL << 16)
/* 0x8100 */
- #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID8100 (UINT32_C(0x1) << 16)
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID8100 (0x1UL << 16)
/* 0x9100 */
- #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9100 (UINT32_C(0x2) << 16)
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9100 (0x2UL << 16)
/* 0x9200 */
- #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9200 (UINT32_C(0x3) << 16)
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9200 (0x3UL << 16)
/* 0x9300 */
- #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9300 (UINT32_C(0x4) << 16)
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9300 (0x4UL << 16)
/* Value programmed in CFA VLANTPID register. */
- #define TX_BD_LONG_CFA_META_VLAN_TPID_TPIDCFG (UINT32_C(0x5) << 16)
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPIDCFG (0x5UL << 16)
#define TX_BD_LONG_CFA_META_VLAN_TPID_LAST \
- TX_BD_LONG_CFA_META_VLAN_TPID_TPIDCFG
+ TX_BD_LONG_CFA_META_VLAN_TPID_TPIDCFG
/* When key=1, This is the VLAN tag TPID select value. */
- #define TX_BD_LONG_CFA_META_VLAN_RESERVED_MASK UINT32_C(0xff80000)
- #define TX_BD_LONG_CFA_META_VLAN_RESERVED_SFT 19
+ #define TX_BD_LONG_CFA_META_VLAN_RESERVED_MASK 0xff80000UL
+ #define TX_BD_LONG_CFA_META_VLAN_RESERVED_SFT 19
/*
* This field identifies the type of edit to be performed on the
* packet. This value must be valid on the first BD of a packet.
*/
- #define TX_BD_LONG_CFA_META_KEY_MASK UINT32_C(0xf0000000)
- #define TX_BD_LONG_CFA_META_KEY_SFT 28
+ #define TX_BD_LONG_CFA_META_KEY_MASK 0xf0000000UL
+ #define TX_BD_LONG_CFA_META_KEY_SFT 28
/* No editing */
- #define TX_BD_LONG_CFA_META_KEY_NONE (UINT32_C(0x0) << 28)
+ #define TX_BD_LONG_CFA_META_KEY_NONE (0x0UL << 28)
/*
- * - meta[17:16] - TPID select value (0 =
+ * - meta[17:16] - TPID select value (0 =
* 0x8100). - meta[15:12] - PRI/DE value. -
* meta[11:0] - VID value.
*/
- #define TX_BD_LONG_CFA_META_KEY_VLAN_TAG (UINT32_C(0x1) << 28)
+ #define TX_BD_LONG_CFA_META_KEY_VLAN_TAG (0x1UL << 28)
#define TX_BD_LONG_CFA_META_KEY_LAST \
- TX_BD_LONG_CFA_META_KEY_VLAN_TAG
+ TX_BD_LONG_CFA_META_KEY_VLAN_TAG
+} __attribute__((packed));
+
+/* Empty TX BD (16 bytes) */
+struct tx_bd_empty {
+ uint8_t type;
+ /* This value identifies the type of buffer descriptor. */
+ #define TX_BD_EMPTY_TYPE_MASK 0x3fUL
+ #define TX_BD_EMPTY_TYPE_SFT 0
+ /*
+ * Indicates that this BD is 1BB long and is an
+ * empty TX BD. Not valid for use by the driver.
+ */
+ #define TX_BD_EMPTY_TYPE_TX_BD_EMPTY 0x1UL
+ uint8_t unused_1[3];
+ uint8_t unused_2;
+ uint8_t unused_3[3];
+ uint64_t unused_4;
} __attribute__((packed));
-/* RX Producer Packet BD (16 bytes) */
+/* RX Producer Packet BD (16 bytes) */
struct rx_prod_pkt_bd {
uint16_t flags_type;
/* This value identifies the type of buffer descriptor. */
- #define RX_PROD_PKT_BD_TYPE_MASK UINT32_C(0x3f)
- #define RX_PROD_PKT_BD_TYPE_SFT 0
+ #define RX_PROD_PKT_BD_TYPE_MASK 0x3fUL
+ #define RX_PROD_PKT_BD_TYPE_SFT 0
/*
* Indicates that this BD is 16B long and is an
- * RX Producer (ie. empty) buffer descriptor.
+ * RX Producer (ie. empty) buffer descriptor.
*/
- #define RX_PROD_PKT_BD_TYPE_RX_PROD_PKT UINT32_C(0x4)
+ #define RX_PROD_PKT_BD_TYPE_RX_PROD_PKT 0x4UL
/*
* If set to 1, the packet will be placed at the address plus
* 2B. The 2 Bytes of padding will be written as zero.
@@ -579,7 +517,7 @@ struct rx_prod_pkt_bd {
* host memory while still allowing writes to be cache line
* aligned.
*/
- #define RX_PROD_PKT_BD_FLAGS_SOP_PAD UINT32_C(0x40)
+ #define RX_PROD_PKT_BD_FLAGS_SOP_PAD 0x40UL
/*
* If set to 1, the packet write will be padded out to the
* nearest cache-line with zero value padding.
@@ -589,7 +527,7 @@ struct rx_prod_pkt_bd {
* feature will ensure that all data writes on the PCI bus
* start/end on cache line boundaries.
*/
- #define RX_PROD_PKT_BD_FLAGS_EOP_PAD UINT32_C(0x80)
+ #define RX_PROD_PKT_BD_FLAGS_EOP_PAD 0x80UL
/*
* This value is the number of additional buffers in the ring
* that describe the buffer space to be consumed for the this
@@ -600,10 +538,10 @@ struct rx_prod_pkt_bd {
* packet. Even if the packet to be placed does not need all the
* additional buffers, they will be consumed anyway.
*/
- #define RX_PROD_PKT_BD_FLAGS_BUFFERS_MASK UINT32_C(0x300)
- #define RX_PROD_PKT_BD_FLAGS_BUFFERS_SFT 8
- #define RX_PROD_PKT_BD_FLAGS_MASK UINT32_C(0xffc0)
- #define RX_PROD_PKT_BD_FLAGS_SFT 6
+ #define RX_PROD_PKT_BD_FLAGS_BUFFERS_MASK 0x300UL
+ #define RX_PROD_PKT_BD_FLAGS_BUFFERS_SFT 8
+ #define RX_PROD_PKT_BD_FLAGS_MASK 0xffc0UL
+ #define RX_PROD_PKT_BD_FLAGS_SFT 6
uint16_t len;
/*
* This is the length in Bytes of the host physical buffer where
@@ -632,9 +570,97 @@ struct rx_prod_pkt_bd {
*/
} __attribute__((packed));
+/* RX Producer Buffer BD (16 bytes) */
+struct rx_prod_bfr_bd {
+ uint16_t flags_type;
+ /* This value identifies the type of buffer descriptor. */
+ #define RX_PROD_BFR_BD_TYPE_MASK 0x3fUL
+ #define RX_PROD_BFR_BD_TYPE_SFT 0
+ /*
+ * Indicates that this BD is 16B long and is an
+ * RX Producer Buffer BD.
+ */
+ #define RX_PROD_BFR_BD_TYPE_RX_PROD_BFR 0x5UL
+ #define RX_PROD_BFR_BD_FLAGS_MASK 0xffc0UL
+ #define RX_PROD_BFR_BD_FLAGS_SFT 6
+ uint16_t len;
+ /*
+ * This is the length in Bytes of the host physical buffer where
+ * data for the packet may be placed in host memory.
+ */
+ /*
+ * While this is a Byte resolution value, it is often
+ * advantageous to ensure that the buffers provided end on a
+ * host cache line.
+ */
+ uint32_t opaque;
+ /* This field is not used. */
+ uint64_t addr;
+ /*
+ * This is the host physical address where data for the packet
+ * may by placed in host memory.
+ */
+ /*
+ * While this is a Byte resolution value, it is often
+ * advantageous to ensure that the buffers provide start on a
+ * host cache line.
+ */
+} __attribute__((packed));
+
+/* RX Producer Aggregation BD (16 bytes) */
+struct rx_prod_agg_bd {
+ uint16_t flags_type;
+ /* This value identifies the type of buffer descriptor. */
+ #define RX_PROD_AGG_BD_TYPE_MASK 0x3fUL
+ #define RX_PROD_AGG_BD_TYPE_SFT 0
+ /*
+ * Indicates that this BD is 16B long and is an
+ * RX Producer Assembly Buffer Descriptor.
+ */
+ #define RX_PROD_AGG_BD_TYPE_RX_PROD_AGG 0x6UL
+ /*
+ * If set to 1, the packet write will be padded out to the
+ * nearest cache-line with zero value padding.
+ */
+ /*
+ * If receive buffers start/end on cache-line boundaries, this
+ * feature will ensure that all data writes on the PCI bus end
+ * on cache line boundaries.
+ */
+ #define RX_PROD_AGG_BD_FLAGS_EOP_PAD 0x40UL
+ #define RX_PROD_AGG_BD_FLAGS_MASK 0xffc0UL
+ #define RX_PROD_AGG_BD_FLAGS_SFT 6
+ uint16_t len;
+ /*
+ * This is the length in Bytes of the host physical buffer where
+ * data for the packet may be placed in host memory.
+ */
+ /*
+ * While this is a Byte resolution value, it is often
+ * advantageous to ensure that the buffers provided end on a
+ * host cache line.
+ */
+ uint32_t opaque;
+ /*
+ * The opaque data field is pass through to the completion and
+ * can be used for any data that the driver wants to associate
+ * with this receive assembly buffer.
+ */
+ uint64_t addr;
+ /*
+ * This is the host physical address where data for the packet
+ * may by placed in host memory.
+ */
+ /*
+ * While this is a Byte resolution value, it is often
+ * advantageous to ensure that the buffers provide start on a
+ * host cache line.
+ */
+} __attribute__((packed));
+
/* Completion Ring Structures */
/* Note: This structure is used by the HWRM to communicate HWRM Error. */
-/* Base Completion Record (16 bytes) */
+/* Base Completion Record (16 bytes) */
struct cmpl_base {
uint16_t type;
/* unused is 10 b */
@@ -644,55 +670,55 @@ struct cmpl_base {
* 16B units. Even values indicate 16B records. Odd values
* indicate 32B records.
*/
- #define CMPL_BASE_TYPE_MASK UINT32_C(0x3f)
- #define CMPL_BASE_TYPE_SFT 0
+ #define CMPL_BASE_TYPE_MASK 0x3fUL
+ #define CMPL_BASE_TYPE_SFT 0
/* TX L2 completion: Completion of TX packet. Length = 16B */
- #define CMPL_BASE_TYPE_TX_L2 UINT32_C(0x0)
+ #define CMPL_BASE_TYPE_TX_L2 0x0UL
/*
* RX L2 completion: Completion of and L2 RX
* packet. Length = 32B
*/
- #define CMPL_BASE_TYPE_RX_L2 UINT32_C(0x11)
+ #define CMPL_BASE_TYPE_RX_L2 0x11UL
/*
* RX Aggregation Buffer completion : Completion
* of an L2 aggregation buffer in support of
* TPA, HDS, or Jumbo packet completion. Length
* = 16B
*/
- #define CMPL_BASE_TYPE_RX_AGG UINT32_C(0x12)
+ #define CMPL_BASE_TYPE_RX_AGG 0x12UL
/*
* RX L2 TPA Start Completion: Completion at the
* beginning of a TPA operation. Length = 32B
*/
- #define CMPL_BASE_TYPE_RX_TPA_START UINT32_C(0x13)
+ #define CMPL_BASE_TYPE_RX_TPA_START 0x13UL
/*
* RX L2 TPA End Completion: Completion at the
* end of a TPA operation. Length = 32B
*/
- #define CMPL_BASE_TYPE_RX_TPA_END UINT32_C(0x15)
+ #define CMPL_BASE_TYPE_RX_TPA_END 0x15UL
/*
* Statistics Ejection Completion: Completion of
* statistics data ejection buffer. Length = 16B
*/
- #define CMPL_BASE_TYPE_STAT_EJECT UINT32_C(0x1a)
+ #define CMPL_BASE_TYPE_STAT_EJECT 0x1aUL
/* HWRM Command Completion: Completion of an HWRM command. */
- #define CMPL_BASE_TYPE_HWRM_DONE UINT32_C(0x20)
+ #define CMPL_BASE_TYPE_HWRM_DONE 0x20UL
/* Forwarded HWRM Request */
- #define CMPL_BASE_TYPE_HWRM_FWD_REQ UINT32_C(0x22)
+ #define CMPL_BASE_TYPE_HWRM_FWD_REQ 0x22UL
/* Forwarded HWRM Response */
- #define CMPL_BASE_TYPE_HWRM_FWD_RESP UINT32_C(0x24)
+ #define CMPL_BASE_TYPE_HWRM_FWD_RESP 0x24UL
/* HWRM Asynchronous Event Information */
- #define CMPL_BASE_TYPE_HWRM_ASYNC_EVENT UINT32_C(0x2e)
+ #define CMPL_BASE_TYPE_HWRM_ASYNC_EVENT 0x2eUL
/* CQ Notification */
- #define CMPL_BASE_TYPE_CQ_NOTIFICATION UINT32_C(0x30)
+ #define CMPL_BASE_TYPE_CQ_NOTIFICATION 0x30UL
/* SRQ Threshold Event */
- #define CMPL_BASE_TYPE_SRQ_EVENT UINT32_C(0x32)
+ #define CMPL_BASE_TYPE_SRQ_EVENT 0x32UL
/* DBQ Threshold Event */
- #define CMPL_BASE_TYPE_DBQ_EVENT UINT32_C(0x34)
+ #define CMPL_BASE_TYPE_DBQ_EVENT 0x34UL
/* QP Async Notification */
- #define CMPL_BASE_TYPE_QP_EVENT UINT32_C(0x38)
+ #define CMPL_BASE_TYPE_QP_EVENT 0x38UL
/* Function Async Notification */
- #define CMPL_BASE_TYPE_FUNC_EVENT UINT32_C(0x3a)
+ #define CMPL_BASE_TYPE_FUNC_EVENT 0x3aUL
/* unused is 10 b */
uint16_t info1;
/* info1 is 16 b */
@@ -705,15 +731,15 @@ struct cmpl_base {
* different for each pass through the completion queue. The
* even passes will write 1. The odd passes will write 0.
*/
- #define CMPL_BASE_V UINT32_C(0x1)
+ #define CMPL_BASE_V 0x1UL
/* info3 is 31 b */
- #define CMPL_BASE_INFO3_MASK UINT32_C(0xfffffffe)
- #define CMPL_BASE_INFO3_SFT 1
+ #define CMPL_BASE_INFO3_MASK 0xfffffffeUL
+ #define CMPL_BASE_INFO3_SFT 1
uint32_t info4;
/* info4 is 32 b */
} __attribute__((packed));
-/* TX Completion Record (16 bytes) */
+/* TX Completion Record (16 bytes) */
struct tx_cmpl {
uint16_t flags_type;
/*
@@ -722,15 +748,15 @@ struct tx_cmpl {
* 16B units. Even values indicate 16B records. Odd values
* indicate 32B records.
*/
- #define TX_CMPL_TYPE_MASK UINT32_C(0x3f)
- #define TX_CMPL_TYPE_SFT 0
+ #define TX_CMPL_TYPE_MASK 0x3fUL
+ #define TX_CMPL_TYPE_SFT 0
/* TX L2 completion: Completion of TX packet. Length = 16B */
- #define TX_CMPL_TYPE_TX_L2 UINT32_C(0x0)
+ #define TX_CMPL_TYPE_TX_L2 0x0UL
/*
* When this bit is '1', it indicates a packet that has an error
* of some type. Type of error is indicated in error_flags.
*/
- #define TX_CMPL_FLAGS_ERROR UINT32_C(0x40)
+ #define TX_CMPL_FLAGS_ERROR 0x40UL
/*
* When this bit is '1', it indicates that the packet completed
* was transmitted using the push acceleration data provided by
@@ -738,9 +764,9 @@ struct tx_cmpl {
* packet had not push acceleration data written or was executed
* as a normal packet even though push data was provided.
*/
- #define TX_CMPL_FLAGS_PUSH UINT32_C(0x80)
- #define TX_CMPL_FLAGS_MASK UINT32_C(0xffc0)
- #define TX_CMPL_FLAGS_SFT 6
+ #define TX_CMPL_FLAGS_PUSH 0x80UL
+ #define TX_CMPL_FLAGS_MASK 0xffc0UL
+ #define TX_CMPL_FLAGS_SFT 6
uint16_t unused_0;
/* unused1 is 16 b */
uint32_t opaque;
@@ -754,55 +780,55 @@ struct tx_cmpl {
* different for each pass through the completion queue. The
* even passes will write 1. The odd passes will write 0.
*/
- #define TX_CMPL_V UINT32_C(0x1)
+ #define TX_CMPL_V 0x1UL
/*
* This error indicates that there was some sort of problem with
* the BDs for the packet.
*/
- #define TX_CMPL_ERRORS_BUFFER_ERROR_MASK UINT32_C(0xe)
- #define TX_CMPL_ERRORS_BUFFER_ERROR_SFT 1
+ #define TX_CMPL_ERRORS_BUFFER_ERROR_MASK 0xeUL
+ #define TX_CMPL_ERRORS_BUFFER_ERROR_SFT 1
/* No error */
- #define TX_CMPL_ERRORS_BUFFER_ERROR_NO_ERROR (UINT32_C(0x0) << 1)
+ #define TX_CMPL_ERRORS_BUFFER_ERROR_NO_ERROR (0x0UL << 1)
/* Bad Format: BDs were not formatted correctly. */
- #define TX_CMPL_ERRORS_BUFFER_ERROR_BAD_FMT (UINT32_C(0x2) << 1)
+ #define TX_CMPL_ERRORS_BUFFER_ERROR_BAD_FMT (0x2UL << 1)
#define TX_CMPL_ERRORS_BUFFER_ERROR_LAST \
- TX_CMPL_ERRORS_BUFFER_ERROR_BAD_FMT
+ TX_CMPL_ERRORS_BUFFER_ERROR_BAD_FMT
/*
* When this bit is '1', it indicates that the length of the
* packet was zero. No packet was transmitted.
*/
- #define TX_CMPL_ERRORS_ZERO_LENGTH_PKT UINT32_C(0x10)
+ #define TX_CMPL_ERRORS_ZERO_LENGTH_PKT 0x10UL
/*
* When this bit is '1', it indicates that the packet was longer
* than the programmed limit in TDI. No packet was transmitted.
*/
- #define TX_CMPL_ERRORS_EXCESSIVE_BD_LENGTH UINT32_C(0x20)
+ #define TX_CMPL_ERRORS_EXCESSIVE_BD_LENGTH 0x20UL
/*
* When this bit is '1', it indicates that one or more of the
* BDs associated with this packet generated a PCI error. This
* probably means the address was not valid.
*/
- #define TX_CMPL_ERRORS_DMA_ERROR UINT32_C(0x40)
+ #define TX_CMPL_ERRORS_DMA_ERROR 0x40UL
/*
* When this bit is '1', it indicates that the packet was longer
* than indicated by the hint. No packet was transmitted.
*/
- #define TX_CMPL_ERRORS_HINT_TOO_SHORT UINT32_C(0x80)
+ #define TX_CMPL_ERRORS_HINT_TOO_SHORT 0x80UL
/*
* When this bit is '1', it indicates that the packet was
* dropped due to Poison TLP error on one or more of the TLPs in
* the PXP completion.
*/
- #define TX_CMPL_ERRORS_POISON_TLP_ERROR UINT32_C(0x100)
- #define TX_CMPL_ERRORS_MASK UINT32_C(0xfffe)
- #define TX_CMPL_ERRORS_SFT 1
+ #define TX_CMPL_ERRORS_POISON_TLP_ERROR 0x100UL
+ #define TX_CMPL_ERRORS_MASK 0xfffeUL
+ #define TX_CMPL_ERRORS_SFT 1
uint16_t unused_1;
/* unused2 is 16 b */
uint32_t unused_2;
/* unused3 is 32 b */
} __attribute__((packed));
-/* RX Packet Completion Record (32 bytes split to 2 16-byte struct) */
+/* RX Packet Completion Record (32 bytes split to 2 16-byte struct) */
struct rx_pkt_cmpl {
uint16_t flags_type;
/*
@@ -811,99 +837,97 @@ struct rx_pkt_cmpl {
* 16B units. Even values indicate 16B records. Odd values
* indicate 32B records.
*/
- #define RX_PKT_CMPL_TYPE_MASK UINT32_C(0x3f)
- #define RX_PKT_CMPL_TYPE_SFT 0
+ #define RX_PKT_CMPL_TYPE_MASK 0x3fUL
+ #define RX_PKT_CMPL_TYPE_SFT 0
/*
* RX L2 completion: Completion of and L2 RX
* packet. Length = 32B
*/
- #define RX_PKT_CMPL_TYPE_RX_L2 UINT32_C(0x11)
- #define RX_PKT_CMPL_TYPE_RX_L2_TPA_START UINT32_C(0x13)
- #define RX_PKT_CMPL_TYPE_RX_L2_TPA_END UINT32_C(0x15)
+ #define RX_PKT_CMPL_TYPE_RX_L2 0x11UL
/*
* When this bit is '1', it indicates a packet that has an error
* of some type. Type of error is indicated in error_flags.
*/
- #define RX_PKT_CMPL_FLAGS_ERROR UINT32_C(0x40)
+ #define RX_PKT_CMPL_FLAGS_ERROR 0x40UL
/* This field indicates how the packet was placed in the buffer. */
- #define RX_PKT_CMPL_FLAGS_PLACEMENT_MASK UINT32_C(0x380)
- #define RX_PKT_CMPL_FLAGS_PLACEMENT_SFT 7
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_MASK 0x380UL
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_SFT 7
/* Normal: Packet was placed using normal algorithm. */
- #define RX_PKT_CMPL_FLAGS_PLACEMENT_NORMAL (UINT32_C(0x0) << 7)
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_NORMAL (0x0UL << 7)
/* Jumbo: Packet was placed using jumbo algorithm. */
- #define RX_PKT_CMPL_FLAGS_PLACEMENT_JUMBO (UINT32_C(0x1) << 7)
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_JUMBO (0x1UL << 7)
/*
* Header/Data Separation: Packet was placed
* using Header/Data separation algorithm. The
* separation location is indicated by the itype
* field.
*/
- #define RX_PKT_CMPL_FLAGS_PLACEMENT_HDS (UINT32_C(0x2) << 7)
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_HDS (0x2UL << 7)
#define RX_PKT_CMPL_FLAGS_PLACEMENT_LAST \
- RX_PKT_CMPL_FLAGS_PLACEMENT_HDS
+ RX_PKT_CMPL_FLAGS_PLACEMENT_HDS
/* This bit is '1' if the RSS field in this completion is valid. */
- #define RX_PKT_CMPL_FLAGS_RSS_VALID UINT32_C(0x400)
+ #define RX_PKT_CMPL_FLAGS_RSS_VALID 0x400UL
/* unused is 1 b */
- #define RX_PKT_CMPL_FLAGS_UNUSED UINT32_C(0x800)
+ #define RX_PKT_CMPL_FLAGS_UNUSED 0x800UL
/*
* This value indicates what the inner packet determined for the
* packet was.
*/
- #define RX_PKT_CMPL_FLAGS_ITYPE_MASK UINT32_C(0xf000)
- #define RX_PKT_CMPL_FLAGS_ITYPE_SFT 12
+ #define RX_PKT_CMPL_FLAGS_ITYPE_MASK 0xf000UL
+ #define RX_PKT_CMPL_FLAGS_ITYPE_SFT 12
/* Not Known: Indicates that the packet type was not known. */
- #define RX_PKT_CMPL_FLAGS_ITYPE_NOT_KNOWN (UINT32_C(0x0) << 12)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_NOT_KNOWN (0x0UL << 12)
/*
* IP Packet: Indicates that the packet was an
* IP packet, but further classification was not
* possible.
*/
- #define RX_PKT_CMPL_FLAGS_ITYPE_IP (UINT32_C(0x1) << 12)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_IP (0x1UL << 12)
/*
* TCP Packet: Indicates that the packet was IP
* and TCP. This indicates that the
* payload_offset field is valid.
*/
- #define RX_PKT_CMPL_FLAGS_ITYPE_TCP (UINT32_C(0x2) << 12)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_TCP (0x2UL << 12)
/*
* UDP Packet: Indicates that the packet was IP
* and UDP. This indicates that the
* payload_offset field is valid.
*/
- #define RX_PKT_CMPL_FLAGS_ITYPE_UDP (UINT32_C(0x3) << 12)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_UDP (0x3UL << 12)
/*
* FCoE Packet: Indicates that the packet was
* recognized as a FCoE. This also indicates
* that the payload_offset field is valid.
*/
- #define RX_PKT_CMPL_FLAGS_ITYPE_FCOE (UINT32_C(0x4) << 12)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_FCOE (0x4UL << 12)
/*
* RoCE Packet: Indicates that the packet was
* recognized as a RoCE. This also indicates
* that the payload_offset field is valid.
*/
- #define RX_PKT_CMPL_FLAGS_ITYPE_ROCE (UINT32_C(0x5) << 12)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_ROCE (0x5UL << 12)
/*
* ICMP Packet: Indicates that the packet was
* recognized as ICMP. This indicates that the
* payload_offset field is valid.
*/
- #define RX_PKT_CMPL_FLAGS_ITYPE_ICMP (UINT32_C(0x7) << 12)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_ICMP (0x7UL << 12)
/*
* PtP packet wo/timestamp: Indicates that the
* packet was recognized as a PtP packet.
*/
- #define RX_PKT_CMPL_FLAGS_ITYPE_PTP_WO_TIMESTAMP (UINT32_C(0x8) << 12)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_PTP_WO_TIMESTAMP (0x8UL << 12)
/*
* PtP packet w/timestamp: Indicates that the
* packet was recognized as a PtP packet and
* that a timestamp was taken for the packet.
*/
- #define RX_PKT_CMPL_FLAGS_ITYPE_PTP_W_TIMESTAMP (UINT32_C(0x9) << 12)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_PTP_W_TIMESTAMP (0x9UL << 12)
#define RX_PKT_CMPL_FLAGS_ITYPE_LAST \
- RX_PKT_CMPL_FLAGS_ITYPE_PTP_W_TIMESTAMP
- #define RX_PKT_CMPL_FLAGS_MASK UINT32_C(0xffc0)
- #define RX_PKT_CMPL_FLAGS_SFT 6
+ RX_PKT_CMPL_FLAGS_ITYPE_PTP_W_TIMESTAMP
+ #define RX_PKT_CMPL_FLAGS_MASK 0xffc0UL
+ #define RX_PKT_CMPL_FLAGS_SFT 6
uint16_t len;
/*
* This is the length of the data for the packet stored in the
@@ -923,7 +947,7 @@ struct rx_pkt_cmpl {
* different for each pass through the completion queue. The
* even passes will write 1. The odd passes will write 0.
*/
- #define RX_PKT_CMPL_V1 UINT32_C(0x1)
+ #define RX_PKT_CMPL_V1 0x1UL
/*
* This value is the number of aggregation buffers that follow
* this entry in the completion ring that are a part of this
@@ -931,8 +955,8 @@ struct rx_pkt_cmpl {
* contained in the buffer space provided for the packet in the
* RX ring.
*/
- #define RX_PKT_CMPL_AGG_BUFS_MASK UINT32_C(0x3e)
- #define RX_PKT_CMPL_AGG_BUFS_SFT 1
+ #define RX_PKT_CMPL_AGG_BUFS_MASK 0x3eUL
+ #define RX_PKT_CMPL_AGG_BUFS_SFT 1
/* unused1 is 2 b */
uint8_t rss_hash_type;
/*
@@ -986,30 +1010,30 @@ struct rx_pkt_cmpl_hi {
* inner packet and that the ip_cs_error field indicates if
* there was an error.
*/
- #define RX_PKT_CMPL_FLAGS2_IP_CS_CALC UINT32_C(0x1)
+ #define RX_PKT_CMPL_FLAGS2_IP_CS_CALC 0x1UL
/*
* This indicates that the TCP, UDP or ICMP checksum was
* calculated for the inner packet and that the l4_cs_error
* field indicates if there was an error.
*/
- #define RX_PKT_CMPL_FLAGS2_L4_CS_CALC UINT32_C(0x2)
+ #define RX_PKT_CMPL_FLAGS2_L4_CS_CALC 0x2UL
/*
* This indicates that the ip checksum was calculated for the
* tunnel header and that the t_ip_cs_error field indicates if
* there was an error.
*/
- #define RX_PKT_CMPL_FLAGS2_T_IP_CS_CALC UINT32_C(0x4)
+ #define RX_PKT_CMPL_FLAGS2_T_IP_CS_CALC 0x4UL
/*
* This indicates that the UDP checksum was calculated for the
* tunnel packet and that the t_l4_cs_error field indicates if
* there was an error.
*/
- #define RX_PKT_CMPL_FLAGS2_T_L4_CS_CALC UINT32_C(0x8)
+ #define RX_PKT_CMPL_FLAGS2_T_L4_CS_CALC 0x8UL
/* This value indicates what format the metadata field is. */
- #define RX_PKT_CMPL_FLAGS2_META_FORMAT_MASK UINT32_C(0xf0)
- #define RX_PKT_CMPL_FLAGS2_META_FORMAT_SFT 4
+ #define RX_PKT_CMPL_FLAGS2_META_FORMAT_MASK 0xf0UL
+ #define RX_PKT_CMPL_FLAGS2_META_FORMAT_SFT 4
/* No metadata informtaion. Value is zero. */
- #define RX_PKT_CMPL_FLAGS2_META_FORMAT_NONE (UINT32_C(0x0) << 4)
+ #define RX_PKT_CMPL_FLAGS2_META_FORMAT_NONE (0x0UL << 4)
/*
* The metadata field contains the VLAN tag and
* TPID value. - metadata[11:0] contains the
@@ -1018,49 +1042,49 @@ struct rx_pkt_cmpl_hi {
* vlan PRI value. - metadata[31:16] contains
* the vlan TPID value.
*/
- #define RX_PKT_CMPL_FLAGS2_META_FORMAT_VLAN (UINT32_C(0x1) << 4)
+ #define RX_PKT_CMPL_FLAGS2_META_FORMAT_VLAN (0x1UL << 4)
#define RX_PKT_CMPL_FLAGS2_META_FORMAT_LAST \
- RX_PKT_CMPL_FLAGS2_META_FORMAT_VLAN
+ RX_PKT_CMPL_FLAGS2_META_FORMAT_VLAN
/*
* This field indicates the IP type for the inner-most IP
* header. A value of '0' indicates IPv4. A value of '1'
* indicates IPv6. This value is only valid if itype indicates a
* packet with an IP header.
*/
- #define RX_PKT_CMPL_FLAGS2_IP_TYPE UINT32_C(0x100)
+ #define RX_PKT_CMPL_FLAGS2_IP_TYPE 0x100UL
uint32_t metadata;
/*
* This is data from the CFA block as indicated by the
* meta_format field.
*/
/* When meta_format=1, this value is the VLAN VID. */
- #define RX_PKT_CMPL_METADATA_VID_MASK UINT32_C(0xfff)
- #define RX_PKT_CMPL_METADATA_VID_SFT 0
+ #define RX_PKT_CMPL_METADATA_VID_MASK 0xfffUL
+ #define RX_PKT_CMPL_METADATA_VID_SFT 0
/* When meta_format=1, this value is the VLAN DE. */
- #define RX_PKT_CMPL_METADATA_DE UINT32_C(0x1000)
+ #define RX_PKT_CMPL_METADATA_DE 0x1000UL
/* When meta_format=1, this value is the VLAN PRI. */
- #define RX_PKT_CMPL_METADATA_PRI_MASK UINT32_C(0xe000)
- #define RX_PKT_CMPL_METADATA_PRI_SFT 13
+ #define RX_PKT_CMPL_METADATA_PRI_MASK 0xe000UL
+ #define RX_PKT_CMPL_METADATA_PRI_SFT 13
/* When meta_format=1, this value is the VLAN TPID. */
- #define RX_PKT_CMPL_METADATA_TPID_MASK UINT32_C(0xffff0000)
- #define RX_PKT_CMPL_METADATA_TPID_SFT 16
+ #define RX_PKT_CMPL_METADATA_TPID_MASK 0xffff0000UL
+ #define RX_PKT_CMPL_METADATA_TPID_SFT 16
uint16_t errors_v2;
/*
* This value is written by the NIC such that it will be
* different for each pass through the completion queue. The
* even passes will write 1. The odd passes will write 0.
*/
- #define RX_PKT_CMPL_V2 UINT32_C(0x1)
+ #define RX_PKT_CMPL_V2 0x1UL
/*
* This error indicates that there was some sort of problem with
* the BDs for the packet that was found after part of the
* packet was already placed. The packet should be treated as
* invalid.
*/
- #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_MASK UINT32_C(0xe)
- #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_SFT 1
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_MASK 0xeUL
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_SFT 1
/* No buffer error */
- #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_NO_BUFFER (UINT32_C(0x0) << 1)
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_NO_BUFFER (0x0UL << 1)
/*
* Did Not Fit: Packet did not fit into packet
* buffer provided. For regular placement, this
@@ -1069,73 +1093,70 @@ struct rx_pkt_cmpl_hi {
* means that the packet could not be placed
* into 7 physical buffers or less.
*/
- #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_DID_NOT_FIT \
- (UINT32_C(0x1) << 1)
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_DID_NOT_FIT (0x1UL << 1)
/*
* Not On Chip: All BDs needed for the packet
* were not on-chip when the packet arrived.
*/
- #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_NOT_ON_CHIP \
- (UINT32_C(0x2) << 1)
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_NOT_ON_CHIP (0x2UL << 1)
/* Bad Format: BDs were not formatted correctly. */
- #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_BAD_FORMAT \
- (UINT32_C(0x3) << 1)
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_BAD_FORMAT (0x3UL << 1)
#define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_LAST \
- RX_PKT_CMPL_ERRORS_BUFFER_ERROR_BAD_FORMAT
+ RX_PKT_CMPL_ERRORS_BUFFER_ERROR_BAD_FORMAT
/* This indicates that there was an error in the IP header checksum. */
- #define RX_PKT_CMPL_ERRORS_IP_CS_ERROR UINT32_C(0x10)
+ #define RX_PKT_CMPL_ERRORS_IP_CS_ERROR 0x10UL
/*
* This indicates that there was an error in the TCP, UDP or
* ICMP checksum.
*/
- #define RX_PKT_CMPL_ERRORS_L4_CS_ERROR UINT32_C(0x20)
+ #define RX_PKT_CMPL_ERRORS_L4_CS_ERROR 0x20UL
/*
* This indicates that there was an error in the tunnel IP
* header checksum.
*/
- #define RX_PKT_CMPL_ERRORS_T_IP_CS_ERROR UINT32_C(0x40)
+ #define RX_PKT_CMPL_ERRORS_T_IP_CS_ERROR 0x40UL
/*
* This indicates that there was an error in the tunnel UDP
* checksum.
*/
- #define RX_PKT_CMPL_ERRORS_T_L4_CS_ERROR UINT32_C(0x80)
+ #define RX_PKT_CMPL_ERRORS_T_L4_CS_ERROR 0x80UL
/*
* This indicates that there was a CRC error on either an FCoE
* or RoCE packet. The itype indicates the packet type.
*/
- #define RX_PKT_CMPL_ERRORS_CRC_ERROR UINT32_C(0x100)
+ #define RX_PKT_CMPL_ERRORS_CRC_ERROR 0x100UL
/*
* This indicates that there was an error in the tunnel portion
* of the packet when this field is non-zero.
*/
- #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_MASK UINT32_C(0xe00)
- #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_SFT 9
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_MASK 0xe00UL
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_SFT 9
/*
* No additional error occurred on the tunnel
* portion of the packet of the packet does not
* have a tunnel.
*/
- #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_NO_ERROR (UINT32_C(0x0) << 9)
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_NO_ERROR (0x0UL << 9)
/*
* Indicates that IP header version does not
* match expectation from L2 Ethertype for IPv4
* and IPv6 in the tunnel header.
*/
#define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_VERSION \
- (UINT32_C(0x1) << 9)
+ (0x1UL << 9)
/*
* Indicates that header length is out of range
* in the tunnel header. Valid for IPv4.
*/
#define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_HDR_LEN \
- (UINT32_C(0x2) << 9)
+ (0x2UL << 9)
/*
* Indicates that the physical packet is shorter
* than that claimed by the PPPoE header length
* for a tunnel PPPoE packet.
*/
#define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_TUNNEL_TOTAL_ERROR \
- (UINT32_C(0x3) << 9)
+ (0x3UL << 9)
/*
* Indicates that physical packet is shorter
* than that claimed by the tunnel l3 header
@@ -1143,7 +1164,7 @@ struct rx_pkt_cmpl_hi {
* packets.
*/
#define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_IP_TOTAL_ERROR \
- (UINT32_C(0x4) << 9)
+ (0x4UL << 9)
/*
* Indicates that the physical packet is shorter
* than that claimed by the tunnel UDP header
@@ -1151,82 +1172,75 @@ struct rx_pkt_cmpl_hi {
* fragmented.
*/
#define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_UDP_TOTAL_ERROR \
- (UINT32_C(0x5) << 9)
+ (0x5UL << 9)
/*
* indicates that the IPv4 TTL or IPv6 hop limit
- * check have failed (e.g. TTL = 0) in the
+ * check have failed (e.g. TTL = 0) in the
* tunnel header. Valid for IPv4, and IPv6.
*/
- #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL \
- (UINT32_C(0x6) << 9)
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL (0x6UL << 9)
#define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_LAST \
- RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL
+ RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL
/*
* This indicates that there was an error in the inner portion
* of the packet when this field is non-zero.
*/
- #define RX_PKT_CMPL_ERRORS_PKT_ERROR_MASK UINT32_C(0xf000)
- #define RX_PKT_CMPL_ERRORS_PKT_ERROR_SFT 12
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_MASK 0xf000UL
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_SFT 12
/*
* No additional error occurred on the tunnel
* portion of the packet of the packet does not
* have a tunnel.
*/
- #define RX_PKT_CMPL_ERRORS_PKT_ERROR_NO_ERROR (UINT32_C(0x0) << 12)
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_NO_ERROR (0x0UL << 12)
/*
* Indicates that IP header version does not
* match expectation from L2 Ethertype for IPv4
* and IPv6 or that option other than VFT was
* parsed on FCoE packet.
*/
- #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_VERSION \
- (UINT32_C(0x1) << 12)
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_VERSION (0x1UL << 12)
/*
* indicates that header length is out of range.
* Valid for IPv4 and RoCE
*/
- #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_HDR_LEN \
- (UINT32_C(0x2) << 12)
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_HDR_LEN (0x2UL << 12)
/*
* indicates that the IPv4 TTL or IPv6 hop limit
- * check have failed (e.g. TTL = 0). Valid for
+ * check have failed (e.g. TTL = 0). Valid for
* IPv4, and IPv6
*/
- #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_TTL (UINT32_C(0x3) << 12)
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_TTL (0x3UL << 12)
/*
* Indicates that physical packet is shorter
* than that claimed by the l3 header length.
* Valid for IPv4, IPv6 packet or RoCE packets.
*/
- #define RX_PKT_CMPL_ERRORS_PKT_ERROR_IP_TOTAL_ERROR \
- (UINT32_C(0x4) << 12)
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_IP_TOTAL_ERROR (0x4UL << 12)
/*
* Indicates that the physical packet is shorter
* than that claimed by the UDP header length
* for a UDP packet that is not fragmented.
*/
- #define RX_PKT_CMPL_ERRORS_PKT_ERROR_UDP_TOTAL_ERROR \
- (UINT32_C(0x5) << 12)
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_UDP_TOTAL_ERROR (0x5UL << 12)
/*
* Indicates that TCP header length > IP
* payload. Valid for TCP packets only.
*/
- #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN \
- (UINT32_C(0x6) << 12)
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN (0x6UL << 12)
/* Indicates that TCP header length < 5. Valid for TCP. */
#define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN_TOO_SMALL \
- (UINT32_C(0x7) << 12)
+ (0x7UL << 12)
/*
* Indicates that TCP option headers result in a
* TCP header size that does not match data
* offset in TCP header. Valid for TCP.
*/
- #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN \
- (UINT32_C(0x8) << 12)
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN (0x8UL << 12)
#define RX_PKT_CMPL_ERRORS_PKT_ERROR_LAST \
- RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN
- #define RX_PKT_CMPL_ERRORS_MASK UINT32_C(0xfffe)
- #define RX_PKT_CMPL_ERRORS_SFT 1
+ RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN
+ #define RX_PKT_CMPL_ERRORS_MASK 0xfffeUL
+ #define RX_PKT_CMPL_ERRORS_SFT 1
uint16_t cfa_code;
/*
* This field identifies the CFA action rule that was used for
@@ -1240,8 +1254,8 @@ struct rx_pkt_cmpl_hi {
* bottom 8 to 10b of the rss_hash value. The bottom 20b of this
* value contain the ordering domain value for the packet.
*/
- #define RX_PKT_CMPL_REORDER_MASK UINT32_C(0xffffff)
- #define RX_PKT_CMPL_REORDER_SFT 0
+ #define RX_PKT_CMPL_REORDER_MASK 0xffffffUL
+ #define RX_PKT_CMPL_REORDER_SFT 0
} __attribute__((packed));
/* RX L2 TPA Start Completion Record (32 bytes split to 2 16-byte struct) */
@@ -1253,18 +1267,18 @@ struct rx_tpa_start_cmpl {
* 16B units. Even values indicate 16B records. Odd values
* indicate 32B records.
*/
- #define RX_TPA_START_CMPL_TYPE_MASK UINT32_C(0x3f)
- #define RX_TPA_START_CMPL_TYPE_SFT 0
+ #define RX_TPA_START_CMPL_TYPE_MASK 0x3fUL
+ #define RX_TPA_START_CMPL_TYPE_SFT 0
/*
* RX L2 TPA Start Completion: Completion at the
* beginning of a TPA operation. Length = 32B
*/
- #define RX_TPA_START_CMPL_TYPE_RX_TPA_START UINT32_C(0x13)
+ #define RX_TPA_START_CMPL_TYPE_RX_TPA_START 0x13UL
/* This bit will always be '0' for TPA start completions. */
- #define RX_TPA_START_CMPL_FLAGS_ERROR UINT32_C(0x40)
+ #define RX_TPA_START_CMPL_FLAGS_ERROR 0x40UL
/* This field indicates how the packet was placed in the buffer. */
- #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_MASK UINT32_C(0x380)
- #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_SFT 7
+ #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_MASK 0x380UL
+ #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_SFT 7
/*
* Jumbo: TPA Packet was placed using jumbo
* algorithm. This means that the first buffer
@@ -1273,14 +1287,14 @@ struct rx_tpa_start_cmpl {
* will be filled before moving to the next
* aggregation buffer.
*/
- #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_JUMBO (UINT32_C(0x1) << 7)
+ #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_JUMBO (0x1UL << 7)
/*
* Header/Data Separation: Packet was placed
* using Header/Data separation algorithm. The
* separation location is indicated by the itype
* field.
*/
- #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_HDS (UINT32_C(0x2) << 7)
+ #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_HDS (0x2UL << 7)
/*
* GRO/Jumbo: Packet will be placed using
* GRO/Jumbo where the first packet is filled
@@ -1289,8 +1303,7 @@ struct rx_tpa_start_cmpl {
* aggregation buffers unless it starts at the
* beginning of an aggregation buffer.
*/
- #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_GRO_JUMBO \
- (UINT32_C(0x5) << 7)
+ #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_GRO_JUMBO (0x5UL << 7)
/*
* GRO/Header-Data Separation: Packet will be
* placed using GRO/HDS where the header is in
@@ -1299,25 +1312,25 @@ struct rx_tpa_start_cmpl {
* span two aggregation buffers unless it starts
* at the beginning of an aggregation buffer.
*/
- #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_GRO_HDS (UINT32_C(0x6) << 7)
+ #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_GRO_HDS (0x6UL << 7)
#define RX_TPA_START_CMPL_FLAGS_PLACEMENT_LAST \
- RX_TPA_START_CMPL_FLAGS_PLACEMENT_GRO_HDS
+ RX_TPA_START_CMPL_FLAGS_PLACEMENT_GRO_HDS
/* This bit is '1' if the RSS field in this completion is valid. */
- #define RX_TPA_START_CMPL_FLAGS_RSS_VALID UINT32_C(0x400)
+ #define RX_TPA_START_CMPL_FLAGS_RSS_VALID 0x400UL
/* unused is 1 b */
- #define RX_TPA_START_CMPL_FLAGS_UNUSED UINT32_C(0x800)
+ #define RX_TPA_START_CMPL_FLAGS_UNUSED 0x800UL
/*
* This value indicates what the inner packet determined for the
* packet was.
*/
- #define RX_TPA_START_CMPL_FLAGS_ITYPE_MASK UINT32_C(0xf000)
- #define RX_TPA_START_CMPL_FLAGS_ITYPE_SFT 12
+ #define RX_TPA_START_CMPL_FLAGS_ITYPE_MASK 0xf000UL
+ #define RX_TPA_START_CMPL_FLAGS_ITYPE_SFT 12
/* TCP Packet: Indicates that the packet was IP and TCP. */
- #define RX_TPA_START_CMPL_FLAGS_ITYPE_TCP (UINT32_C(0x2) << 12)
+ #define RX_TPA_START_CMPL_FLAGS_ITYPE_TCP (0x2UL << 12)
#define RX_TPA_START_CMPL_FLAGS_ITYPE_LAST \
- RX_TPA_START_CMPL_FLAGS_ITYPE_TCP
- #define RX_TPA_START_CMPL_FLAGS_MASK UINT32_C(0xffc0)
- #define RX_TPA_START_CMPL_FLAGS_SFT 6
+ RX_TPA_START_CMPL_FLAGS_ITYPE_TCP
+ #define RX_TPA_START_CMPL_FLAGS_MASK 0xffc0UL
+ #define RX_TPA_START_CMPL_FLAGS_SFT 6
uint16_t len;
/*
* This value indicates the amount of packet data written to the
@@ -1335,7 +1348,7 @@ struct rx_tpa_start_cmpl {
* different for each pass through the completion queue. The
* even passes will write 1. The odd passes will write 0.
*/
- #define RX_TPA_START_CMPL_V1 UINT32_C(0x1)
+ #define RX_TPA_START_CMPL_V1 0x1UL
/* unused1 is 7 b */
uint8_t rss_hash_type;
/*
@@ -1377,8 +1390,8 @@ struct rx_tpa_start_cmpl {
* with. Use this number to correlate the TPA start completion
* with the TPA end completion.
*/
- #define RX_TPA_START_CMPL_AGG_ID_MASK UINT32_C(0xfe00)
- #define RX_TPA_START_CMPL_AGG_ID_SFT 9
+ #define RX_TPA_START_CMPL_AGG_ID_MASK 0xfe00UL
+ #define RX_TPA_START_CMPL_AGG_ID_SFT 9
uint32_t rss_hash;
/*
* This value is the RSS hash value calculated for the packet
@@ -1394,30 +1407,30 @@ struct rx_tpa_start_cmpl_hi {
* inner packet and that the sum passed for all segments
* included in the aggregation.
*/
- #define RX_TPA_START_CMPL_FLAGS2_IP_CS_CALC UINT32_C(0x1)
+ #define RX_TPA_START_CMPL_FLAGS2_IP_CS_CALC 0x1UL
/*
* This indicates that the TCP, UDP or ICMP checksum was
* calculated for the inner packet and that the sum passed for
* all segments included in the aggregation.
*/
- #define RX_TPA_START_CMPL_FLAGS2_L4_CS_CALC UINT32_C(0x2)
+ #define RX_TPA_START_CMPL_FLAGS2_L4_CS_CALC 0x2UL
/*
* This indicates that the ip checksum was calculated for the
* tunnel header and that the sum passed for all segments
* included in the aggregation.
*/
- #define RX_TPA_START_CMPL_FLAGS2_T_IP_CS_CALC UINT32_C(0x4)
+ #define RX_TPA_START_CMPL_FLAGS2_T_IP_CS_CALC 0x4UL
/*
* This indicates that the UDP checksum was calculated for the
* tunnel packet and that the sum passed for all segments
* included in the aggregation.
*/
- #define RX_TPA_START_CMPL_FLAGS2_T_L4_CS_CALC UINT32_C(0x8)
+ #define RX_TPA_START_CMPL_FLAGS2_T_L4_CS_CALC 0x8UL
/* This value indicates what format the metadata field is. */
- #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_MASK UINT32_C(0xf0)
- #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_SFT 4
+ #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_MASK 0xf0UL
+ #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_SFT 4
/* No metadata informtaion. Value is zero. */
- #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_NONE (UINT32_C(0x0) << 4)
+ #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_NONE (0x0UL << 4)
/*
* The metadata field contains the VLAN tag and
* TPID value. - metadata[11:0] contains the
@@ -1426,31 +1439,31 @@ struct rx_tpa_start_cmpl_hi {
* vlan PRI value. - metadata[31:16] contains
* the vlan TPID value.
*/
- #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_VLAN (UINT32_C(0x1) << 4)
+ #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_VLAN (0x1UL << 4)
#define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_LAST \
- RX_TPA_START_CMPL_FLAGS2_META_FORMAT_VLAN
+ RX_TPA_START_CMPL_FLAGS2_META_FORMAT_VLAN
/*
* This field indicates the IP type for the inner-most IP
* header. A value of '0' indicates IPv4. A value of '1'
* indicates IPv6.
*/
- #define RX_TPA_START_CMPL_FLAGS2_IP_TYPE UINT32_C(0x100)
+ #define RX_TPA_START_CMPL_FLAGS2_IP_TYPE 0x100UL
uint32_t metadata;
/*
* This is data from the CFA block as indicated by the
* meta_format field.
*/
/* When meta_format=1, this value is the VLAN VID. */
- #define RX_TPA_START_CMPL_METADATA_VID_MASK UINT32_C(0xfff)
- #define RX_TPA_START_CMPL_METADATA_VID_SFT 0
+ #define RX_TPA_START_CMPL_METADATA_VID_MASK 0xfffUL
+ #define RX_TPA_START_CMPL_METADATA_VID_SFT 0
/* When meta_format=1, this value is the VLAN DE. */
- #define RX_TPA_START_CMPL_METADATA_DE UINT32_C(0x1000)
+ #define RX_TPA_START_CMPL_METADATA_DE 0x1000UL
/* When meta_format=1, this value is the VLAN PRI. */
- #define RX_TPA_START_CMPL_METADATA_PRI_MASK UINT32_C(0xe000)
- #define RX_TPA_START_CMPL_METADATA_PRI_SFT 13
+ #define RX_TPA_START_CMPL_METADATA_PRI_MASK 0xe000UL
+ #define RX_TPA_START_CMPL_METADATA_PRI_SFT 13
/* When meta_format=1, this value is the VLAN TPID. */
- #define RX_TPA_START_CMPL_METADATA_TPID_MASK UINT32_C(0xffff0000)
- #define RX_TPA_START_CMPL_METADATA_TPID_SFT 16
+ #define RX_TPA_START_CMPL_METADATA_TPID_MASK 0xffff0000UL
+ #define RX_TPA_START_CMPL_METADATA_TPID_SFT 16
uint16_t v2;
/* unused4 is 15 b */
/*
@@ -1458,7 +1471,7 @@ struct rx_tpa_start_cmpl_hi {
* different for each pass through the completion queue. The
* even passes will write 1. The odd passes will write 0.
*/
- #define RX_TPA_START_CMPL_V2 UINT32_C(0x1)
+ #define RX_TPA_START_CMPL_V2 0x1UL
/* unused4 is 15 b */
uint16_t cfa_code;
/*
@@ -1476,27 +1489,27 @@ struct rx_tpa_start_cmpl_hi {
* for the outer L3 header. If there is no outer L3 header, then
* this value is zero.
*/
- #define RX_TPA_START_CMPL_OUTER_L3_OFFSET_MASK UINT32_C(0x1ff)
- #define RX_TPA_START_CMPL_OUTER_L3_OFFSET_SFT 0
+ #define RX_TPA_START_CMPL_OUTER_L3_OFFSET_MASK 0x1ffUL
+ #define RX_TPA_START_CMPL_OUTER_L3_OFFSET_SFT 0
/*
* This is the offset from the beginning of the packet in bytes
* for the inner most L2 header.
*/
- #define RX_TPA_START_CMPL_INNER_L2_OFFSET_MASK UINT32_C(0x3fe00)
- #define RX_TPA_START_CMPL_INNER_L2_OFFSET_SFT 9
+ #define RX_TPA_START_CMPL_INNER_L2_OFFSET_MASK 0x3fe00UL
+ #define RX_TPA_START_CMPL_INNER_L2_OFFSET_SFT 9
/*
* This is the offset from the beginning of the packet in bytes
* for the inner most L3 header.
*/
- #define RX_TPA_START_CMPL_INNER_L3_OFFSET_MASK UINT32_C(0x7fc0000)
- #define RX_TPA_START_CMPL_INNER_L3_OFFSET_SFT 18
+ #define RX_TPA_START_CMPL_INNER_L3_OFFSET_MASK 0x7fc0000UL
+ #define RX_TPA_START_CMPL_INNER_L3_OFFSET_SFT 18
/*
* This is the size in bytes of the inner most L4 header. This
* can be subtracted from the payload_offset to determine the
* start of the inner most L4 header.
*/
- #define RX_TPA_START_CMPL_INNER_L4_SIZE_MASK UINT32_C(0xf8000000)
- #define RX_TPA_START_CMPL_INNER_L4_SIZE_SFT 27
+ #define RX_TPA_START_CMPL_INNER_L4_SIZE_MASK 0xf8000000UL
+ #define RX_TPA_START_CMPL_INNER_L4_SIZE_SFT 27
} __attribute__((packed));
/* RX TPA End Completion Record (32 bytes split to 2 16-byte struct) */
@@ -1508,21 +1521,21 @@ struct rx_tpa_end_cmpl {
* 16B units. Even values indicate 16B records. Odd values
* indicate 32B records.
*/
- #define RX_TPA_END_CMPL_TYPE_MASK UINT32_C(0x3f)
- #define RX_TPA_END_CMPL_TYPE_SFT 0
+ #define RX_TPA_END_CMPL_TYPE_MASK 0x3fUL
+ #define RX_TPA_END_CMPL_TYPE_SFT 0
/*
* RX L2 TPA End Completion: Completion at the
* end of a TPA operation. Length = 32B
*/
- #define RX_TPA_END_CMPL_TYPE_RX_TPA_END UINT32_C(0x15)
+ #define RX_TPA_END_CMPL_TYPE_RX_TPA_END 0x15UL
/*
* When this bit is '1', it indicates a packet that has an error
* of some type. Type of error is indicated in error_flags.
*/
- #define RX_TPA_END_CMPL_FLAGS_ERROR UINT32_C(0x40)
+ #define RX_TPA_END_CMPL_FLAGS_ERROR 0x40UL
/* This field indicates how the packet was placed in the buffer. */
- #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_MASK UINT32_C(0x380)
- #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_SFT 7
+ #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_MASK 0x380UL
+ #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_SFT 7
/*
* Jumbo: TPA Packet was placed using jumbo
* algorithm. This means that the first buffer
@@ -1531,14 +1544,14 @@ struct rx_tpa_end_cmpl {
* will be filled before moving to the next
* aggregation buffer.
*/
- #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_JUMBO (UINT32_C(0x1) << 7)
+ #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_JUMBO (0x1UL << 7)
/*
* Header/Data Separation: Packet was placed
* using Header/Data separation algorithm. The
* separation location is indicated by the itype
* field.
*/
- #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_HDS (UINT32_C(0x2) << 7)
+ #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_HDS (0x2UL << 7)
/*
* GRO/Jumbo: Packet will be placed using
* GRO/Jumbo where the first packet is filled
@@ -1547,7 +1560,7 @@ struct rx_tpa_end_cmpl {
* aggregation buffers unless it starts at the
* beginning of an aggregation buffer.
*/
- #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_GRO_JUMBO (UINT32_C(0x5) << 7)
+ #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_GRO_JUMBO (0x5UL << 7)
/*
* GRO/Header-Data Separation: Packet will be
* placed using GRO/HDS where the header is in
@@ -1556,12 +1569,12 @@ struct rx_tpa_end_cmpl {
* span two aggregation buffers unless it starts
* at the beginning of an aggregation buffer.
*/
- #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_GRO_HDS (UINT32_C(0x6) << 7)
+ #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_GRO_HDS (0x6UL << 7)
#define RX_TPA_END_CMPL_FLAGS_PLACEMENT_LAST \
- RX_TPA_END_CMPL_FLAGS_PLACEMENT_GRO_HDS
+ RX_TPA_END_CMPL_FLAGS_PLACEMENT_GRO_HDS
/* unused is 2 b */
- #define RX_TPA_END_CMPL_FLAGS_UNUSED_MASK UINT32_C(0xc00)
- #define RX_TPA_END_CMPL_FLAGS_UNUSED_SFT 10
+ #define RX_TPA_END_CMPL_FLAGS_UNUSED_MASK 0xc00UL
+ #define RX_TPA_END_CMPL_FLAGS_UNUSED_SFT 10
/*
* This value indicates what the inner packet determined for the
* packet was. - 2 TCP Packet Indicates that the packet was IP
@@ -1570,10 +1583,10 @@ struct rx_tpa_end_cmpl {
* checksum. This also indicates that the payload_offset field
* is valid.
*/
- #define RX_TPA_END_CMPL_FLAGS_ITYPE_MASK UINT32_C(0xf000)
- #define RX_TPA_END_CMPL_FLAGS_ITYPE_SFT 12
- #define RX_TPA_END_CMPL_FLAGS_MASK UINT32_C(0xffc0)
- #define RX_TPA_END_CMPL_FLAGS_SFT 6
+ #define RX_TPA_END_CMPL_FLAGS_ITYPE_MASK 0xf000UL
+ #define RX_TPA_END_CMPL_FLAGS_ITYPE_SFT 12
+ #define RX_TPA_END_CMPL_FLAGS_MASK 0xffc0UL
+ #define RX_TPA_END_CMPL_FLAGS_SFT 6
uint16_t len;
/*
* This value is zero for TPA End completions. There is no data
@@ -1592,7 +1605,7 @@ struct rx_tpa_end_cmpl {
* different for each pass through the completion queue. The
* even passes will write 1. The odd passes will write 0.
*/
- #define RX_TPA_END_CMPL_V1 UINT32_C(0x1)
+ #define RX_TPA_END_CMPL_V1 0x1UL
/*
* This value is the number of aggregation buffers that follow
* this entry in the completion ring that are a part of this
@@ -1600,8 +1613,8 @@ struct rx_tpa_end_cmpl {
* completely contained in the buffer space provided in the
* aggregation start completion.
*/
- #define RX_TPA_END_CMPL_AGG_BUFS_MASK UINT32_C(0x7e)
- #define RX_TPA_END_CMPL_AGG_BUFS_SFT 1
+ #define RX_TPA_END_CMPL_AGG_BUFS_MASK 0x7eUL
+ #define RX_TPA_END_CMPL_AGG_BUFS_SFT 1
/* unused1 is 1 b */
uint8_t tpa_segs;
/* This value is the number of segments in the TPA operation. */
@@ -1624,8 +1637,8 @@ struct rx_tpa_end_cmpl {
* with. Use this number to correlate the TPA start completion
* with the TPA end completion.
*/
- #define RX_TPA_END_CMPL_AGG_ID_MASK UINT32_C(0xfe)
- #define RX_TPA_END_CMPL_AGG_ID_SFT 1
+ #define RX_TPA_END_CMPL_AGG_ID_MASK 0xfeUL
+ #define RX_TPA_END_CMPL_AGG_ID_SFT 1
uint32_t tsdelta;
/*
* For non-GRO packets, this value is the timestamp delta
@@ -1646,8 +1659,8 @@ struct rx_tpa_end_cmpl_hi {
* This value is the number of duplicate ACKs that have been
* received as part of the TPA operation.
*/
- #define RX_TPA_END_CMPL_TPA_DUP_ACKS_MASK UINT32_C(0xf)
- #define RX_TPA_END_CMPL_TPA_DUP_ACKS_SFT 0
+ #define RX_TPA_END_CMPL_TPA_DUP_ACKS_MASK 0xfUL
+ #define RX_TPA_END_CMPL_TPA_DUP_ACKS_SFT 0
/* unused3 is 28 b */
uint16_t tpa_seg_len;
/*
@@ -1668,15 +1681,15 @@ struct rx_tpa_end_cmpl_hi {
* different for each pass through the completion queue. The
* even passes will write 1. The odd passes will write 0.
*/
- #define RX_TPA_END_CMPL_V2 UINT32_C(0x1)
+ #define RX_TPA_END_CMPL_V2 0x1UL
/*
* This error indicates that there was some sort of problem with
* the BDs for the packet that was found after part of the
* packet was already placed. The packet should be treated as
* invalid.
*/
- #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_MASK UINT32_C(0xe)
- #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_SFT 1
+ #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_MASK 0xeUL
+ #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_SFT 1
/*
* This error occurs when there is a fatal HW
* problem in the chip only. It indicates that
@@ -1685,7 +1698,7 @@ struct rx_tpa_end_cmpl_hi {
* block.
*/
#define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_NOT_ON_CHIP \
- (UINT32_C(0x2) << 1)
+ (0x2UL << 1)
/*
* This error occurs when TPA block was not
* configured to reserve adequate BDs for TPA
@@ -1696,12 +1709,11 @@ struct rx_tpa_end_cmpl_hi {
* total aggregation buffers allowed for the TPA
* operation has been exceeded.
*/
- #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_RSV_ERROR \
- (UINT32_C(0x4) << 1)
+ #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_RSV_ERROR (0x4UL << 1)
#define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_LAST \
- RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_RSV_ERROR
- #define RX_TPA_END_CMPL_ERRORS_MASK UINT32_C(0xfffe)
- #define RX_TPA_END_CMPL_ERRORS_SFT 1
+ RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_RSV_ERROR
+ #define RX_TPA_END_CMPL_ERRORS_MASK 0xfffeUL
+ #define RX_TPA_END_CMPL_ERRORS_SFT 1
uint16_t unused_4;
/* unused5 is 16 b */
uint32_t start_opaque;
@@ -1711,7 +1723,124 @@ struct rx_tpa_end_cmpl_hi {
*/
} __attribute__((packed));
-/* HWRM Forwarded Request (16 bytes) */
+/* RX Aggregation Buffer Completion Record (16 bytes) */
+struct rx_abuf_cmpl {
+ uint16_t type;
+ /* unused is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define RX_ABUF_CMPL_TYPE_MASK 0x3fUL
+ #define RX_ABUF_CMPL_TYPE_SFT 0
+ /*
+ * RX Aggregation Buffer completion : Completion
+ * of an L2 aggregation buffer in support of
+ * TPA, HDS, or Jumbo packet completion. Length
+ * = 16B
+ */
+ #define RX_ABUF_CMPL_TYPE_RX_AGG 0x12UL
+ /* unused is 10 b */
+ uint16_t len;
+ /*
+ * This is the length of the data for the packet stored in this
+ * aggregation buffer identified by the opaque value. This does
+ * not include the length of any data placed in other
+ * aggregation BDs or in the packet or buffer BDs. This length
+ * does not include any space added due to hdr_offset register
+ * during HDS placement mode.
+ */
+ uint32_t opaque;
+ /*
+ * This is a copy of the opaque field from the RX BD this
+ * aggregation buffer corresponds to.
+ */
+ uint32_t v;
+ /* unused2 is 31 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define RX_ABUF_CMPL_V 0x1UL
+ /* unused2 is 31 b */
+ uint32_t unused_2;
+ /* unused3 is 32 b */
+} __attribute__((packed));
+
+/* Statistics Ejection Buffer Completion Record (16 bytes) */
+struct eject_cmpl {
+ uint16_t type;
+ /* unused is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_EJECT_CMPL_TYPE_MASK 0x3fUL
+ #define HWRM_EJECT_CMPL_TYPE_SFT 0
+ /*
+ * Statistics Ejection Completion: Completion of
+ * statistics data ejection buffer. Length = 16B
+ */
+ #define HWRM_EJECT_CMPL_TYPE_STAT_EJECT 0x1aUL
+ /* unused is 10 b */
+ uint16_t len;
+ /* This is the length of the statistics data stored in this buffer. */
+ uint32_t opaque;
+ /*
+ * This is a copy of the opaque field from the RX BD this
+ * ejection buffer corresponds to.
+ */
+ uint32_t v;
+ /* unused2 is 31 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_EJECT_CMPL_V 0x1UL
+ /* unused2 is 31 b */
+ uint32_t unused_2;
+ /* unused3 is 32 b */
+} __attribute__((packed));
+
+/* HWRM Completion Record (16 bytes) */
+struct hwrm_cmpl {
+ uint16_t type;
+ /* unused is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define CMPL_TYPE_MASK 0x3fUL
+ #define CMPL_TYPE_SFT 0
+ /* HWRM Command Completion: Completion of an HWRM command. */
+ #define CMPL_TYPE_HWRM_DONE 0x20UL
+ /* unused is 10 b */
+ uint16_t sequence_id;
+ /* This is the sequence_id of the HWRM command that has completed. */
+ uint32_t unused_1;
+ /* unused2 is 32 b */
+ uint32_t v;
+ /* unused3 is 31 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define CMPL_V 0x1UL
+ /* unused3 is 31 b */
+ uint32_t unused_3;
+ /* unused4 is 32 b */
+} __attribute__((packed));
+
+/* HWRM Forwarded Request (16 bytes) */
struct hwrm_fwd_req_cmpl {
uint16_t req_len_type;
/* Length of forwarded request in bytes. */
@@ -1721,13 +1850,13 @@ struct hwrm_fwd_req_cmpl {
* 16B units. Even values indicate 16B records. Odd values
* indicate 32B records.
*/
- #define HWRM_FWD_INPUT_CMPL_TYPE_MASK UINT32_C(0x3f)
- #define HWRM_FWD_INPUT_CMPL_TYPE_SFT 0
+ #define HWRM_FWD_INPUT_CMPL_TYPE_MASK 0x3fUL
+ #define HWRM_FWD_INPUT_CMPL_TYPE_SFT 0
/* Forwarded HWRM Request */
- #define HWRM_FWD_INPUT_CMPL_TYPE_HWRM_FWD_INPUT UINT32_C(0x22)
+ #define HWRM_FWD_INPUT_CMPL_TYPE_HWRM_FWD_INPUT 0x22UL
/* Length of forwarded request in bytes. */
- #define HWRM_FWD_REQ_CMPL_REQ_LEN_MASK UINT32_C(0xffc0)
- #define HWRM_FWD_REQ_CMPL_REQ_LEN_SFT 6
+ #define HWRM_FWD_REQ_CMPL_REQ_LEN_MASK 0xffc0UL
+ #define HWRM_FWD_REQ_CMPL_REQ_LEN_SFT 6
uint16_t source_id;
/*
* Source ID of this request. Typically used in forwarding
@@ -1744,13 +1873,74 @@ struct hwrm_fwd_req_cmpl {
* different for each pass through the completion queue. The
* even passes will write 1. The odd passes will write 0.
*/
- #define HWRM_FWD_INPUT_CMPL_V UINT32_C(0x1)
+ #define HWRM_FWD_INPUT_CMPL_V 0x1UL
/* Address of forwarded request. */
- #define HWRM_FWD_REQ_CMPL_REQ_BUF_ADDR_MASK UINT32_C(0xfffffffe)
- #define HWRM_FWD_REQ_CMPL_REQ_BUF_ADDR_SFT 1
+ #define HWRM_FWD_REQ_CMPL_REQ_BUF_ADDR_MASK 0xfffffffeUL
+ #define HWRM_FWD_REQ_CMPL_REQ_BUF_ADDR_SFT 1
+} __attribute__((packed));
+
+/* HWRM Forwarded Response (16 bytes) */
+struct hwrm_fwd_resp_cmpl {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_FWD_OUTPUT_CMPL_TYPE_MASK 0x3fUL
+ #define HWRM_FWD_OUTPUT_CMPL_TYPE_SFT 0
+ /* Forwarded HWRM Response */
+ #define HWRM_FWD_OUTPUT_CMPL_TYPE_HWRM_FWD_OUTPUT 0x24UL
+ /* unused1 is 10 b */
+ uint16_t source_id;
+ /*
+ * Source ID of this response. Typically used in forwarding
+ * requests and responses. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF -
+ * HWRM
+ */
+ uint16_t resp_len;
+ /* Length of forwarded response in bytes. */
+ uint16_t unused_1;
+ /* unused2 is 16 b */
+ uint32_t resp_buf_addr_v[2];
+ /* Address of forwarded response. */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_FWD_OUTPUT_CMPL_V 0x1UL
+ /* Address of forwarded response. */
+ #define HWRM_FWD_OUTPUT_CMPL_OUTPUT_BUF_ADDR_MASK 0xfffffffeUL
+ #define HWRM_FWD_OUTPUT_CMPL_OUTPUT_BUF_ADDR_SFT 1
} __attribute__((packed));
-/* HWRM Asynchronous Event Completion Record (16 bytes) */
+#define HWRM_GET_EVENT_ID(x) \
+ ((x) == 0x30 ? "VF_FLR": \
+ ((x) == 0x20 ? "PF_DRVR_UNLOAD": \
+ ((x) == 0x10 ? "FUNC_DRVR_UNLOAD": \
+ ((x) == 0xff ? "HWRM_ERROR": \
+ ((x) == 0x32 ? "PF_VF_COMM_STATUS_CHANGE": \
+ ((x) == 0x33 ? "VF_CFG_CHANGE": \
+ ((x) == 0x11 ? "FUNC_DRVR_LOAD": \
+ ((x) == 0x31 ? "VF_MAC_ADDR_CHANGE": \
+ ((x) == 0x34 ? "LLFC_PFC_CHANGE": \
+ ((x) == 0x4 ? "PORT_CONN_NOT_ALLOWED": \
+ ((x) == 0x5 ? "LINK_SPEED_CFG_NOT_ALLOWED": \
+ ((x) == 0x6 ? "LINK_SPEED_CFG_CHANGE": \
+ ((x) == 0x7 ? "PORT_PHY_CFG_CHANGE": \
+ ((x) == 0x0 ? "LINK_STATUS_CHANGE": \
+ ((x) == 0x1 ? "LINK_MTU_CHANGE": \
+ ((x) == 0x2 ? "LINK_SPEED_CHANGE": \
+ ((x) == 0x3 ? "DCB_CONFIG_CHANGE": \
+ ((x) == 0x12 ? "FUNC_FLR_PROC_CMPLT": \
+ ((x) == 0x21 ? "PF_DRVR_LOAD": \
+ "Unknown event_id")))))))))))))))))))
+
+/* HWRM Asynchronous Event Completion Record (16 bytes) */
struct hwrm_async_event_cmpl {
uint16_t type;
/* unused1 is 10 b */
@@ -1760,51 +1950,51 @@ struct hwrm_async_event_cmpl {
* 16B units. Even values indicate 16B records. Odd values
* indicate 32B records.
*/
- #define HWRM_ASYNC_EVENT_CMPL_TYPE_MASK UINT32_C(0x3f)
- #define HWRM_ASYNC_EVENT_CMPL_TYPE_SFT 0
+ #define HWRM_ASYNC_EVENT_CMPL_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_TYPE_SFT 0
/* HWRM Asynchronous Event Information */
- #define HWRM_ASYNC_EVENT_CMPL_TYPE_HWRM_ASYNC_EVENT UINT32_C(0x2e)
+ #define HWRM_ASYNC_EVENT_CMPL_TYPE_HWRM_ASYNC_EVENT 0x2eUL
/* unused1 is 10 b */
uint16_t event_id;
/* Identifiers of events. */
/* Link status changed */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_STATUS_CHANGE UINT32_C(0x0)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_STATUS_CHANGE 0x0UL
/* Link MTU changed */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_MTU_CHANGE UINT32_C(0x1)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_MTU_CHANGE 0x1UL
/* Link speed changed */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CHANGE UINT32_C(0x2)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CHANGE 0x2UL
/* DCB Configuration changed */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_DCB_CONFIG_CHANGE UINT32_C(0x3)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_DCB_CONFIG_CHANGE 0x3UL
/* Port connection not allowed */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PORT_CONN_NOT_ALLOWED UINT32_C(0x4)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PORT_CONN_NOT_ALLOWED 0x4UL
/* Link speed configuration was not allowed */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CFG_NOT_ALLOWED \
- UINT32_C(0x5)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CFG_NOT_ALLOWED 0x5UL
/* Link speed configuration change */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CFG_CHANGE UINT32_C(0x6)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CFG_CHANGE 0x6UL
/* Port PHY configuration change */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PORT_PHY_CFG_CHANGE UINT32_C(0x7)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PORT_PHY_CFG_CHANGE 0x7UL
/* Function driver unloaded */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_UNLOAD UINT32_C(0x10)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_UNLOAD 0x10UL
/* Function driver loaded */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_LOAD UINT32_C(0x11)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_LOAD 0x11UL
/* Function FLR related processing has completed */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_FLR_PROC_CMPLT UINT32_C(0x12)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_FLR_PROC_CMPLT 0x12UL
/* PF driver unloaded */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_UNLOAD UINT32_C(0x20)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_UNLOAD 0x20UL
/* PF driver loaded */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_LOAD UINT32_C(0x21)
- /* VF Function Level Reset (FLR) */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_FLR UINT32_C(0x30)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_LOAD 0x21UL
+ /* VF Function Level Reset (FLR) */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_FLR 0x30UL
/* VF MAC Address Change */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_MAC_ADDR_CHANGE UINT32_C(0x31)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_MAC_ADDR_CHANGE 0x31UL
/* PF-VF communication channel status change. */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_VF_COMM_STATUS_CHANGE \
- UINT32_C(0x32)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_VF_COMM_STATUS_CHANGE 0x32UL
/* VF Configuration Change */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_CFG_CHANGE UINT32_C(0x33)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_CFG_CHANGE 0x33UL
+ /* LLFC/PFC Configuration Change */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LLFC_PFC_CHANGE 0x34UL
/* HWRM Error */
- #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_HWRM_ERROR UINT32_C(0xff)
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_HWRM_ERROR 0xffUL
uint32_t event_data2;
/* Event specific data */
uint8_t opaque_v;
@@ -1814,47 +2004,17330 @@ struct hwrm_async_event_cmpl {
* different for each pass through the completion queue. The
* even passes will write 1. The odd passes will write 0.
*/
- #define HWRM_ASYNC_EVENT_CMPL_V UINT32_C(0x1)
+ #define HWRM_ASYNC_EVENT_CMPL_V 0x1UL
/* opaque is 7 b */
- #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_MASK UINT32_C(0xfe)
- #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_SFT 1
+ #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_SFT 1
uint8_t timestamp_lo;
- /* 8-lsb timestamp from POR (100-msec resolution) */
+ /* 8-lsb timestamp from POR (100-msec resolution) */
uint16_t timestamp_hi;
- /* 16-lsb timestamp from POR (100-msec resolution) */
+ /* 16-lsb timestamp from POR (100-msec resolution) */
uint32_t event_data1;
/* Event specific data */
} __attribute__((packed));
-/* hwrm_ver_get */
-/*
- * Description: This function is called by a driver to determine the HWRM
- * interface version supported by the HWRM firmware, the version of HWRM
- * firmware implementation, the name of HWRM firmware, the versions of other
- * embedded firmwares, and the names of other embedded firmwares, etc. Any
- * interface or firmware version with major = 0, minor = 0, and update = 0 shall
- * be considered an invalid version.
- */
-/* Input (24 bytes) */
-struct hwrm_ver_get_input {
- uint16_t req_type;
+/* HWRM Asynchronous Event Completion Record for link status change (16 bytes) */
+struct hwrm_async_event_cmpl_link_status_change {
+ uint16_t type;
+ /* unused1 is 10 b */
/*
- * This value indicates what type of request this is. The format
- * for the rest of the command is determined by this field.
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
*/
- uint16_t cmpl_ring;
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Link status changed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_ID_LINK_STATUS_CHANGE \
+ 0x0UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
/*
- * This value indicates the what completion ring the request
- * will be optionally completed on. If the value is -1, then no
- * CR completion will be generated. Any other value must be a
- * valid CR ring_id value for this function.
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
*/
- uint16_t seq_id;
- /* This value indicates the command sequence number. */
- uint16_t target_id;
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* Indicates link status change */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_LINK_CHANGE \
+ 0x1UL
/*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function
- * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * If this bit set to 0, then it indicates that
+ * the link was up and it went down.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_LINK_CHANGE_DOWN \
+ (0x0UL << 0)
+ /*
+ * If this bit is set to 1, then it indicates
+ * that the link was down and it went up.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_LINK_CHANGE_UP \
+ (0x1UL << 0)
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_LINK_CHANGE_LAST \
+ HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_LINK_CHANGE_UP
+ /* Indicates the physical port this link status change occur */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_PORT_MASK \
+ 0xeUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_PORT_SFT 1
+ /* PORT ID */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_PORT_ID_MASK \
+ 0xffff0UL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_PORT_ID_SFT \
+ 4
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for link MTU change (16 bytes) */
+struct hwrm_async_event_cmpl_link_mtu_change {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Link MTU changed */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_EVENT_ID_LINK_MTU_CHANGE \
+ 0x1UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* The new MTU of the link in bytes. */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_EVENT_DATA1_NEW_MTU_MASK \
+ 0xffffUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_EVENT_DATA1_NEW_MTU_SFT 0
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for link speed change (16 bytes) */
+struct hwrm_async_event_cmpl_link_speed_change {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Link speed changed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_ID_LINK_SPEED_CHANGE \
+ 0x2UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /*
+ * When this bit is '1', the link was forced to the
+ * force_link_speed value.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_FORCE 0x1UL
+ /* The new link speed in 100 Mbps units. */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_MASK \
+ 0xfffeUL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_SFT \
+ 1
+ /* 100Mb link speed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_100MB \
+ (0x1UL << 1)
+ /* 1Gb link speed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_1GB \
+ (0xaUL << 1)
+ /* 2Gb link speed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_2GB \
+ (0x14UL << 1)
+ /* 2.5Gb link speed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_2_5GB \
+ (0x19UL << 1)
+ /* 10Gb link speed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_10GB \
+ (0x64UL << 1)
+ /* 20Mb link speed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_20GB \
+ (0xc8UL << 1)
+ /* 25Gb link speed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_25GB \
+ (0xfaUL << 1)
+ /* 40Gb link speed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_40GB \
+ (0x190UL << 1)
+ /* 50Gb link speed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_50GB \
+ (0x1f4UL << 1)
+ /* 100Gb link speed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_100GB \
+ (0x3e8UL << 1)
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_LAST \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_100GB
+ /* PORT ID */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_PORT_ID_MASK \
+ 0xffff0000UL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_PORT_ID_SFT 16
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for DCB Config change (16 bytes) */
+struct hwrm_async_event_cmpl_dcb_config_change {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* DCB Configuration changed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_ID_DCB_CONFIG_CHANGE \
+ 0x3UL
+ uint32_t event_data2;
+ /* Event specific data */
+ /* ETS configuration change */
+ #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA2_ETS 0x1UL
+ /* PFC configuration change */
+ #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA2_PFC 0x2UL
+ /* APP configuration change */
+ #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA2_APP 0x4UL
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* PORT ID */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_PORT_ID_MASK \
+ 0xffffUL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_PORT_ID_SFT 0
+ /* Priority recommended for RoCE traffic */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_ROCE_PRIORITY_MASK \
+ 0xff0000UL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_ROCE_PRIORITY_SFT \
+ 16
+ /* none is 255 */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_ROCE_PRIORITY_NONE \
+ (0xffUL << 16)
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_ROCE_PRIORITY_LAST \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_ROCE_PRIORITY_NONE
+ /* Priority recommended for L2 traffic */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_L2_PRIORITY_MASK \
+ 0xff000000UL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_L2_PRIORITY_SFT \
+ 24
+ /* none is 255 */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_L2_PRIORITY_NONE \
+ (0xffUL << 24)
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_L2_PRIORITY_LAST \
+ HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_L2_PRIORITY_NONE
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for port connection not allowed (16 bytes) */
+struct hwrm_async_event_cmpl_port_conn_not_allowed {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Port connection not allowed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_ID_PORT_CONN_NOT_ALLOWED \
+ 0x4UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* PORT ID */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_PORT_ID_MASK \
+ 0xffffUL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_PORT_ID_SFT \
+ 0
+ /*
+ * This value indicates the current port level enforcement
+ * policy for the optics module when there is an optical module
+ * mismatch and port is not connected.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_MASK \
+ 0xff0000UL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_SFT \
+ 16
+ /* No enforcement */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_NONE \
+ (0x0UL << 16)
+ /* Disable Transmit side Laser. */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_DISABLETX \
+ (0x1UL << 16)
+ /* Raise a warning message. */
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_WARNINGMSG \
+ (0x2UL << 16)
+ /* Power down the module. */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_PWRDOWN \
+ (0x3UL << 16)
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_LAST \
+ HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_PWRDOWN
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for link speed config not allowed (16 bytes) */
+struct hwrm_async_event_cmpl_link_speed_cfg_not_allowed {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_TYPE_MASK \
+ 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Link speed configuration was not allowed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_EVENT_ID_LINK_SPEED_CFG_NOT_ALLOWED \
+ 0x5UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_OPAQUE_MASK \
+ 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* PORT ID */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_EVENT_DATA1_PORT_ID_MASK \
+ 0xffffUL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_EVENT_DATA1_PORT_ID_SFT \
+ 0
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for link speed configuration change (16 bytes) */
+struct hwrm_async_event_cmpl_link_speed_cfg_change {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Link speed configuration change */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_ID_LINK_SPEED_CFG_CHANGE \
+ 0x6UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* PORT ID */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_DATA1_PORT_ID_MASK \
+ 0xffffUL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_DATA1_PORT_ID_SFT \
+ 0
+ /*
+ * If set to 1, it indicates that the supported link speeds
+ * configuration on the port has changed. If set to 0, then
+ * there is no change in supported link speeds configuration.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_DATA1_SUPPORTED_LINK_SPEEDS_CHANGE \
+ 0x10000UL
+ /*
+ * If set to 1, it indicates that the link speed configuration
+ * on the port has become illegal or invalid. If set to 0, then
+ * the link speed configuration on the port is legal or valid.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_DATA1_ILLEGAL_LINK_SPEED_CFG \
+ 0x20000UL
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for port PHY configuration change (16 bytes) */
+struct hwrm_async_event_cmpl_port_phy_cfg_change {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Port PHY configuration change */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_ID_PORT_PHY_CFG_CHANGE \
+ 0x7UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* PORT ID */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_DATA1_PORT_ID_MASK \
+ 0xffffUL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_DATA1_PORT_ID_SFT \
+ 0
+ /*
+ * If set to 1, it indicates that the FEC configuration on the
+ * port has changed. If set to 0, then there is no change in FEC
+ * configuration.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_DATA1_FEC_CFG_CHANGE \
+ 0x10000UL
+ /*
+ * If set to 1, it indicates that the EEE configuration on the
+ * port has changed. If set to 0, then there is no change in EEE
+ * configuration on the port.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_DATA1_EEE_CFG_CHANGE \
+ 0x20000UL
+ /*
+ * If set to 1, it indicates that the pause configuration on the
+ * PHY has changed. If set to 0, then there is no change in the
+ * pause configuration on the PHY.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_DATA1_PAUSE_CFG_CHANGE \
+ 0x40000UL
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for Function Driver Unload (16 bytes) */
+struct hwrm_async_event_cmpl_func_drvr_unload {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Function driver unloaded */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_EVENT_ID_FUNC_DRVR_UNLOAD \
+ 0x10UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* Function ID */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_EVENT_DATA1_FUNC_ID_MASK \
+ 0xffffUL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_EVENT_DATA1_FUNC_ID_SFT 0
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for Function Driver load (16 bytes) */
+struct hwrm_async_event_cmpl_func_drvr_load {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Function driver loaded */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_EVENT_ID_FUNC_DRVR_LOAD \
+ 0x11UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* Function ID */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_EVENT_DATA1_FUNC_ID_MASK \
+ 0xffffUL
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_EVENT_DATA1_FUNC_ID_SFT 0
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record to indicate completion of FLR related processing (16 bytes) */
+struct hwrm_async_event_cmpl_func_flr_proc_cmplt {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Function FLR related processing has completed */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_EVENT_ID_FUNC_FLR_PROC_CMPLT \
+ 0x12UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* Function ID */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_EVENT_DATA1_FUNC_ID_MASK \
+ 0xffffUL
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_EVENT_DATA1_FUNC_ID_SFT \
+ 0
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for PF Driver Unload (16 bytes) */
+struct hwrm_async_event_cmpl_pf_drvr_unload {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* PF driver unloaded */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_ID_PF_DRVR_UNLOAD \
+ 0x20UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* PF ID */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_DATA1_FUNC_ID_MASK \
+ 0xffffUL
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_DATA1_FUNC_ID_SFT 0
+ /* Indicates the physical port this pf belongs to */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_DATA1_PORT_MASK \
+ 0x70000UL
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_DATA1_PORT_SFT 16
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for PF Driver load (16 bytes) */
+struct hwrm_async_event_cmpl_pf_drvr_load {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_TYPE_HWRM_ASYNC_EVENT 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* PF driver loaded */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_ID_PF_DRVR_LOAD 0x21UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* PF ID */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_DATA1_FUNC_ID_MASK \
+ 0xffffUL
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_DATA1_FUNC_ID_SFT 0
+ /* Indicates the physical port this pf belongs to */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_DATA1_PORT_MASK \
+ 0x70000UL
+ #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_DATA1_PORT_SFT 16
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for VF FLR (16 bytes) */
+struct hwrm_async_event_cmpl_vf_flr {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_TYPE_HWRM_ASYNC_EVENT 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* VF Function Level Reset (FLR) */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_EVENT_ID_VF_FLR 0x30UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* VF ID */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_EVENT_DATA1_VF_ID_MASK 0xffffUL
+ #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_EVENT_DATA1_VF_ID_SFT 0
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for VF MAC Addr change (16 bytes) */
+struct hwrm_async_event_cmpl_vf_mac_addr_change {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* VF MAC Address Change */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_EVENT_ID_VF_MAC_ADDR_CHANGE \
+ 0x31UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* VF ID */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_EVENT_DATA1_VF_ID_MASK \
+ 0xffffUL
+ #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_EVENT_DATA1_VF_ID_SFT 0
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for PF-VF communication status change (16 bytes) */
+struct hwrm_async_event_cmpl_pf_vf_comm_status_change {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* PF-VF communication channel status change. */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_EVENT_ID_PF_VF_COMM_STATUS_CHANGE \
+ 0x32UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_V 0x1UL
+ /* opaque is 7 b */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /*
+ * If this bit is set to 1, then it indicates that the PF-VF
+ * communication was lost and it is established. If this bit set
+ * to 0, then it indicates that the PF-VF communication was
+ * established and it is lost.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_EVENT_DATA1_COMM_ESTABLISHED \
+ 0x1UL
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for VF configuration change (16 bytes) */
+struct hwrm_async_event_cmpl_vf_cfg_change {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_TYPE_HWRM_ASYNC_EVENT 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* VF Configuration Change */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_ID_VF_CFG_CHANGE \
+ 0x33UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /*
+ * Each flag provided in this field indicates a specific VF
+ * configuration change. At least one of these flags shall be
+ * set to 1 when an asynchronous event completion of this type
+ * is provided by the HWRM.
+ */
+ /*
+ * If this bit is set to 1, then the value of MTU was changed on
+ * this VF. If set to 0, then this bit should be ignored.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_DATA1_MTU_CHANGE 0x1UL
+ /*
+ * If this bit is set to 1, then the value of MRU was changed on
+ * this VF. If set to 0, then this bit should be ignored.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_DATA1_MRU_CHANGE 0x2UL
+ /*
+ * If this bit is set to 1, then the value of default MAC
+ * address was changed on this VF. If set to 0, then this bit
+ * should be ignored.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_DATA1_DFLT_MAC_ADDR_CHANGE \
+ 0x4UL
+ /*
+ * If this bit is set to 1, then the value of default VLAN was
+ * changed on this VF. If set to 0, then this bit should be
+ * ignored.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_DATA1_DFLT_VLAN_CHANGE \
+ 0x8UL
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for llfc pfc status change (16 bytes) */
+struct hwrm_async_event_cmpl_llfc_pfc_change {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_TYPE_HWRM_ASYNC_EVENT \
+ 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* LLFC/PFC Configuration Change */
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_ID_LLFC_PFC_CHANGE \
+ 0x34UL
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* Indicates llfc pfc status change */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_MASK \
+ 0x3UL
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_SFT 0
+ /*
+ * If this field set to 1, then it indicates
+ * that llfc is enabled.
+ */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_LLFC \
+ (0x1UL << 0)
+ /*
+ * If this field is set to 2, then it indicates
+ * that pfc is enabled.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_PFC \
+ (0x2UL << 0)
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_LAST \
+ HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_PFC
+ /* Indicates the physical port this llfc pfc change occur */
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_PORT_MASK \
+ 0x1cUL
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_PORT_SFT 2
+ /* PORT ID */
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_PORT_ID_MASK \
+ 0x1fffe0UL
+ #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_PORT_ID_SFT 5
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record for HWRM Error (16 bytes) */
+struct hwrm_async_event_cmpl_hwrm_error {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_TYPE_MASK 0x3fUL
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_TYPE_HWRM_ASYNC_EVENT 0x2eUL
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* HWRM Error */
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_ID_HWRM_ERROR 0xffUL
+ uint32_t event_data2;
+ /* Event specific data */
+ /* Severity of HWRM Error */
+ #define \
+ HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_MASK 0xffUL
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_SFT 0
+ /* Warning */
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_WARNING \
+ 0x0UL
+ /* Non-fatal Error */
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_NONFATAL \
+ 0x1UL
+ /* Fatal Error */
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_FATAL \
+ 0x2UL
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_LAST \
+ ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_FATAL
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_V 0x1UL
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_OPAQUE_MASK 0xfeUL
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+ /* Time stamp for error event */
+ #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA1_TIMESTAMP 0x1UL
+} __attribute__((packed));
+
+/* Door Bell Formats */
+/*
+ * Description: The backup version of the packet must be valid in the TX ring
+ * before the push doorbell is written to the chip. The first 32b and the BD
+ * portion of the push doorbell must be written in multiples of 32b units on the
+ * PCI interface. The data portion of the push doorbell may be written in
+ * multiples of 8b units on the PCI interface. A push update must contain
+ * exactly one push packet. The backup version of the packet must start with a
+ * long (32B) BD and the BDs must be less than or equal to 16x16B units long.
+ */
+/*
+ * Note: This door bell format is used by the driver when it wants to push a
+ * packet into the chip for super-fast transmission. This pushes a partial BD
+ * and the packet data into the chip. If the chip has room, it will transmit the
+ * packet. If the chip dosn't have room, it will read the BD and packet data
+ * from host memory as a normal packet.
+ */
+/* TX Door Bell Format (4 bytes) */
+struct tx_doorbell {
+ uint32_t key_idx;
+ /*
+ * This value indicates the type of door bell operation that is
+ * begin requested. This value is '0' for TX door bell
+ * operations.
+ */
+ /*
+ * BD Index of next BD that will be used to transmit data on the
+ * TX ring mapped to this door bell. NIC may read and process
+ * all BDs up to, but not including this index.
+ */
+ #define TX_DOORBELL_IDX_MASK 0xffffffUL
+ #define TX_DOORBELL_IDX_SFT 0
+ /* reserved is 4 b */
+ #define TX_DOORBELL_RESERVED_MASK 0xf000000UL
+ #define TX_DOORBELL_RESERVED_SFT 24
+ /*
+ * This value indicates the type of door bell operation that is
+ * begin requested. This value is '0' for TX door bell
+ * operations.
+ */
+ #define TX_DOORBELL_KEY_MASK 0xf0000000UL
+ #define TX_DOORBELL_KEY_SFT 28
+ /* TX Operation */
+ #define TX_DOORBELL_KEY_TX (0x0UL << 28)
+} __attribute__((packed));
+
+/* RX Door Bell Format (4 bytes) */
+struct rx_doorbell {
+ uint32_t key_idx;
+ /*
+ * This value indicates the type of door bell operation that is
+ * begin requested. This value is '1' for RX door bell
+ * operations.
+ */
+ /*
+ * BD Index of next BD that will be used for an empty receive
+ * buffer on the RX ring mapped to this door bell. NIC may read
+ * and process all BDs up to, but not including this index.
+ */
+ #define RX_DOORBELL_IDX_MASK 0xffffffUL
+ #define RX_DOORBELL_IDX_SFT 0
+ /* reserved is 4 b */
+ #define RX_DOORBELL_RESERVED_MASK 0xf000000UL
+ #define RX_DOORBELL_RESERVED_SFT 24
+ /*
+ * This value indicates the type of door bell operation that is
+ * begin requested. This value is '1' for RX door bell
+ * operations.
+ */
+ #define RX_DOORBELL_KEY_MASK 0xf0000000UL
+ #define RX_DOORBELL_KEY_SFT 28
+ /* RX Operation */
+ #define RX_DOORBELL_KEY_RX (0x1UL << 28)
+} __attribute__((packed));
+
+/* CMP Door Bell Format (4 bytes) */
+struct cmpl_doorbell {
+ uint32_t key_mask_valid_idx;
+ /*
+ * This value indicates the type of door bell operation that is
+ * begin requested. This value is '2' for CMP door bell
+ * operations.
+ */
+ /*
+ * BD Index of the most recently handed completion record on the
+ * completion ring mapped to this door bell. NIC may write this
+ * location again with a new completion.
+ */
+ #define CMPL_DOORBELL_IDX_MASK 0xffffffUL
+ #define CMPL_DOORBELL_IDX_SFT 0
+ /* reserved is 2 b */
+ #define CMPL_DOORBELL_RESERVED_MASK 0x3000000UL
+ #define CMPL_DOORBELL_RESERVED_SFT 24
+ /*
+ * This indicates if the BDIDX value is valid for this update
+ * when it is '1'. When it is '0', the BDIDX value should be
+ * ignored.
+ */
+ #define CMPL_DOORBELL_IDX_VALID 0x4000000UL
+ /*
+ * This bit indicates the new interrupt mask state for the
+ * interrupt associated with the BDIDX. A '1', means the
+ * interrupt is to be masked. A '0' indicates the interrupt is
+ * to be unmasked.
+ */
+ #define CMPL_DOORBELL_MASK 0x8000000UL
+ /*
+ * This value indicates the type of door bell operation that is
+ * begin requested. This value is '2' for CMP door bell
+ * operations.
+ */
+ #define CMPL_DOORBELL_KEY_MASK 0xf0000000UL
+ #define CMPL_DOORBELL_KEY_SFT 28
+ /* Completion Operation */
+ #define CMPL_DOORBELL_KEY_CMPL (0x2UL << 28)
+} __attribute__((packed));
+
+/* Status Door Bell Format (4 bytes) */
+struct status_doorbell {
+ uint32_t key_idx;
+ /*
+ * This value indicates the type of door bell operation that is
+ * begin requested. This value is '3' for Status door bell
+ * operations.
+ */
+ /*
+ * BD Index of the status record for which space is now
+ * available to the NIC.
+ */
+ /*
+ * While there is no actual BD associated with the index, the
+ * similar scheme is being used to communicate to the NIC that
+ * space is available for status completions.
+ */
+ #define HWRM_STATUS_DOORBELL_IDX_MASK 0xffffffUL
+ #define HWRM_STATUS_DOORBELL_IDX_SFT 0
+ /* reserved is 4 b */
+ #define HWRM_STATUS_DOORBELL_RESERVED_MASK 0xf000000UL
+ #define HWRM_STATUS_DOORBELL_RESERVED_SFT 24
+ /*
+ * This value indicates the type of door bell operation that is
+ * begin requested. This value is '3' for Status door bell
+ * operations.
+ */
+ #define HWRM_STATUS_DOORBELL_KEY_MASK 0xf0000000UL
+ #define HWRM_STATUS_DOORBELL_KEY_SFT 28
+ /* Status Operation */
+ #define HWRM_STATUS_DOORBELL_KEY_STAT (0x3UL << 28)
+} __attribute__((packed));
+
+/* Push w/32B BD Door Bell Format (32 bytes) */
+struct push32_doorbell {
+ uint32_t key_sz_idx;
+ /*
+ * This value indicates the type of door bell operation that is
+ * begin requested. This value is 4 for push door bell
+ * operations.
+ */
+ /*
+ * This is the BD Index of last BD of the push packet that will
+ * be used to transmit data on the TX ring mapped to this door
+ * bell.
+ */
+ #define HWRM_PUSH32_DOORBELL_IDX_MASK 0xffffffUL
+ #define HWRM_PUSH32_DOORBELL_IDX_SFT 0
+ /*
+ * This is the number of 16B BDs spaces consumed in the TX Ring
+ * by the "backup" version of the packet being pushed. A value
+ * of 1 is invalid since backup must start with a long 32B BE. A
+ * value of 2 indicates just the first 32B BE. A value of 3
+ * indicates 32B+16B BD. etc. A value of 0 indicates 16x16B BD
+ * spaces are consumed.
+ */
+ #define HWRM_PUSH32_DOORBELL_SZ_MASK 0xf000000UL
+ #define HWRM_PUSH32_DOORBELL_SZ_SFT 24
+ /*
+ * This value indicates the type of door bell operation that is
+ * begin requested. This value is 4 for push door bell
+ * operations.
+ */
+ #define HWRM_PUSH32_DOORBELL_KEY_MASK 0xf0000000UL
+ #define HWRM_PUSH32_DOORBELL_KEY_SFT 28
+ /* Push Operation */
+ #define HWRM_PUSH32_DOORBELL_KEY_PUSH (0x4UL << 28)
+ uint16_t flags_type;
+ /*
+ * All bits in this field must be valid on the first BD of a
+ * packet. Only the packet_end bit must be valid for the
+ * remaining BDs of a packet.
+ */
+ /* This value identifies the type of buffer descriptor. */
+ #define HWRM_PUSH32_DOORBELL_TYPE_MASK 0x3fUL
+ #define HWRM_PUSH32_DOORBELL_TYPE_SFT 0
+ /*
+ * Indicates that this BD is 32B long and is
+ * used for normal L2 packet transmission.
+ */
+ #define HWRM_PUSH32_DOORBELL_TYPE_TX_BD_LONG 0x10UL
+ /*
+ * If set to 1, the packet ends with the data in the buffer
+ * pointed to by this descriptor. This flag must be valid on
+ * every BD. This bit must be set on all push doorbells.
+ */
+ #define HWRM_PUSH32_DOORBELL_FLAGS_PACKET_END 0x40UL
+ /*
+ * If set to 1, the device will not generate a completion for
+ * this transmit packet unless there is an error in it's
+ * processing. If this bit is set to 0, then the packet will be
+ * completed normally. This bit must be valid only on the first
+ * BD of a packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_FLAGS_NO_CMPL 0x80UL
+ /*
+ * This value must match the sz field in the first 32b of the
+ * push operation except that if 16x16B BD locations are
+ * consumed in the ring by this packet, then this value must be
+ * 16 (not zero).
+ */
+ #define HWRM_PUSH32_DOORBELL_FLAGS_BD_CNT_MASK 0x1f00UL
+ #define HWRM_PUSH32_DOORBELL_FLAGS_BD_CNT_SFT 8
+ /*
+ * This value is a hint for the length of the entire packet. It
+ * is used by the chip to optimize internal processing. The
+ * packet will be dropped if the hint is too short. This field
+ * is valid only on the first BD of a packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_FLAGS_LHINT_MASK 0x6000UL
+ #define HWRM_PUSH32_DOORBELL_FLAGS_LHINT_SFT 13
+ /* indicates packet length < 512B */
+ #define HWRM_PUSH32_DOORBELL_FLAGS_LHINT_LT512 (0x0UL << 13)
+ /* indicates 512 <= packet length < 1KB */
+ #define HWRM_PUSH32_DOORBELL_FLAGS_LHINT_LT1K (0x1UL << 13)
+ /* indicates 1KB <= packet length < 2KB */
+ #define HWRM_PUSH32_DOORBELL_FLAGS_LHINT_LT2K (0x2UL << 13)
+ /* indicates packet length >= 2KB */
+ #define HWRM_PUSH32_DOORBELL_FLAGS_LHINT_GTE2K (0x3UL << 13)
+ #define HWRM_PUSH32_DOORBELL_FLAGS_LHINT_LAST \
+ PUSH32_DOORBELL_FLAGS_LHINT_GTE2K
+ /*
+ * If set to 1, the device immediately updates the Send Consumer
+ * Index after the buffer associated with this descriptor has
+ * been transferred via DMA to NIC memory from host memory. An
+ * interrupt may or may not be generated according to the state
+ * of the interrupt avoidance mechanisms. If this bit is set to
+ * 0, then the Consumer Index is only updated as soon as one of
+ * the host interrupt coalescing conditions has been met. This
+ * bit must be valid on the first BD of a packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_FLAGS_COAL_NOW 0x8000UL
+ /*
+ * All bits in this field must be valid on the first BD of a
+ * packet. Only the packet_end bit must be valid for the
+ * remaining BDs of a packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_FLAGS_MASK 0xffc0UL
+ #define HWRM_PUSH32_DOORBELL_FLAGS_SFT 6
+ uint16_t len;
+ /*
+ * This is the length of the host physical buffer this BD
+ * describes in bytes. This field must be valid on all BDs of a
+ * packet.
+ */
+ uint32_t opaque;
+ /*
+ * The opaque data field is pass through to the completion and
+ * can be used for any data that the driver wants to associate
+ * with the transmit BD. This field must be valid on the first
+ * BD of a packet.
+ */
+ uint16_t lflags;
+ /*
+ * All bits in this field must be valid on the first BD of a
+ * packet. Their value on other BDs of the packet will be
+ * ignored.
+ */
+ /*
+ * If set to 1, the controller replaces the TCP/UPD checksum
+ * fields of normal TCP/UPD checksum, or the inner TCP/UDP
+ * checksum field of the encapsulated TCP/UDP packets with the
+ * hardware calculated TCP/UDP checksum for the packet
+ * associated with this descriptor. The flag is ignored if the
+ * LSO flag is set. This bit must be valid on the first BD of a
+ * packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_LFLAGS_TCP_UDP_CHKSUM 0x1UL
+ /*
+ * If set to 1, the controller replaces the IP checksum of the
+ * normal packets, or the inner IP checksum of the encapsulated
+ * packets with the hardware calculated IP checksum for the
+ * packet associated with this descriptor. This bit must be
+ * valid on the first BD of a packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_LFLAGS_IP_CHKSUM 0x2UL
+ /*
+ * If set to 1, the controller will not append an Ethernet CRC
+ * to the end of the frame. This bit must be valid on the first
+ * BD of a packet. Packet must be 64B or longer when this flag
+ * is set. It is not useful to use this bit with any form of TX
+ * offload such as CSO or LSO. The intent is that the packet
+ * from the host already has a valid Ethernet CRC on the packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_LFLAGS_NOCRC 0x4UL
+ /*
+ * If set to 1, the device will record the time at which the
+ * packet was actually transmitted at the TX MAC. This bit must
+ * be valid on the first BD of a packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_LFLAGS_STAMP 0x8UL
+ /*
+ * If set to 1, The controller replaces the tunnel IP checksum
+ * field with hardware calculated IP checksum for the IP header
+ * of the packet associated with this descriptor. For outer UDP
+ * checksum, global outer UDP checksum TE_NIC register needs to
+ * be enabled. If the global outer UDP checksum TE_NIC register
+ * bit is set, outer UDP checksum will be calculated for the
+ * following cases: 1. Packets with tcp_udp_chksum flag set to
+ * offload checksum for inner packet AND the inner packet is
+ * TCP/UDP. If the inner packet is ICMP for example (non-
+ * TCP/UDP), even if the tcp_udp_chksum is set, the outer UDP
+ * checksum will not be calculated. 2. Packets with lso flag set
+ * which implies inner TCP checksum calculation as part of LSO
+ * operation.
+ */
+ #define HWRM_PUSH32_DOORBELL_LFLAGS_T_IP_CHKSUM 0x10UL
+ /*
+ * If set to 1, the device will treat this packet with LSO(Large
+ * Send Offload) processing for both normal or encapsulated
+ * packets, which is a form of TCP segmentation. When this bit
+ * is 1, the hdr_size and mss fields must be valid. The driver
+ * doesn't need to set t_ip_chksum, ip_chksum, and
+ * tcp_udp_chksum flags since the controller will replace the
+ * appropriate checksum fields for segmented packets. When this
+ * bit is 1, the hdr_size and mss fields must be valid.
+ */
+ #define HWRM_PUSH32_DOORBELL_LFLAGS_LSO 0x20UL
+ /*
+ * If set to zero when LSO is '1', then the IPID will be treated
+ * as a 16b number and will be wrapped if it exceeds a value of
+ * 0xffff. If set to one when LSO is '1', then the IPID will be
+ * treated as a 15b number and will be wrapped if it exceeds a
+ * value 0f 0x7fff.
+ */
+ #define HWRM_PUSH32_DOORBELL_LFLAGS_IPID_FMT 0x40UL
+ /*
+ * If set to zero when LSO is '1', then the IPID of the tunnel
+ * IP header will not be modified during LSO operations. If set
+ * to one when LSO is '1', then the IPID of the tunnel IP header
+ * will be incremented for each subsequent segment of an LSO
+ * operation. The flag is ignored if the LSO packet is a normal
+ * (non-tunneled) TCP packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_LFLAGS_T_IPID 0x80UL
+ /*
+ * If set to '1', then the RoCE ICRC will be appended to the
+ * packet. Packet must be a valid RoCE format packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_LFLAGS_ROCE_CRC 0x100UL
+ /*
+ * If set to '1', then the FCoE CRC will be appended to the
+ * packet. Packet must be a valid FCoE format packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_LFLAGS_FCOE_CRC 0x200UL
+ uint16_t hdr_size;
+ /*
+ * When LSO is '1', this field must contain the offset of the
+ * TCP payload from the beginning of the packet in as 16b words.
+ * In case of encapsulated/tunneling packet, this field contains
+ * the offset of the inner TCP payload from beginning of the
+ * packet as 16-bit words. This value must be valid on the first
+ * BD of a packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_HDR_SIZE_MASK 0x1ffUL
+ #define HWRM_PUSH32_DOORBELL_HDR_SIZE_SFT 0
+ uint32_t mss;
+ /*
+ * This is the MSS value that will be used to do the LSO
+ * processing. The value is the length in bytes of the TCP
+ * payload for each segment generated by the LSO operation. This
+ * value must be valid on the first BD of a packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_MSS_MASK 0x7fffUL
+ #define HWRM_PUSH32_DOORBELL_MSS_SFT 0
+ uint16_t unused_2;
+ uint16_t cfa_action;
+ /*
+ * This value selects a CFA action to perform on the packet. Set
+ * this value to zero if no CFA action is desired. This value
+ * must be valid on the first BD of a packet.
+ */
+ uint32_t cfa_meta;
+ /*
+ * This value is action meta-data that defines CFA edit
+ * operations that are done in addition to any action editing.
+ */
+ /* When key=1, This is the VLAN tag VID value. */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_VID_MASK 0xfffUL
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_VID_SFT 0
+ /* When key=1, This is the VLAN tag DE value. */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_DE 0x1000UL
+ /* When key=1, This is the VLAN tag PRI value. */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_PRI_MASK 0xe000UL
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_PRI_SFT 13
+ /* When key=1, This is the VLAN tag TPID select value. */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_TPID_MASK 0x70000UL
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_TPID_SFT 16
+ /* 0x88a8 */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_TPID_TPID88A8 (0x0UL << 16)
+ /* 0x8100 */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_TPID_TPID8100 (0x1UL << 16)
+ /* 0x9100 */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_TPID_TPID9100 (0x2UL << 16)
+ /* 0x9200 */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_TPID_TPID9200 (0x3UL << 16)
+ /* 0x9300 */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_TPID_TPID9300 (0x4UL << 16)
+ /* Value programmed in CFA VLANTPID register. */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_TPID_TPIDCFG (0x5UL << 16)
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_TPID_LAST \
+ PUSH32_DOORBELL_CFA_META_VLAN_TPID_TPIDCFG
+ /* When key=1, This is the VLAN tag TPID select value. */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_RESERVED_MASK 0xff80000UL
+ #define HWRM_PUSH32_DOORBELL_CFA_META_VLAN_RESERVED_SFT 19
+ /*
+ * This field identifies the type of edit to be performed on the
+ * packet. This value must be valid on the first BD of a packet.
+ */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_KEY_MASK 0xf0000000UL
+ #define HWRM_PUSH32_DOORBELL_CFA_META_KEY_SFT 28
+ /* No editing */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_KEY_NONE (0x0UL << 28)
+ /*
+ * - meta[17:16] - TPID select value (0 =
+ * 0x8100). - meta[15:12] - PRI/DE value. -
+ * meta[11:0] - VID value.
+ */
+ #define HWRM_PUSH32_DOORBELL_CFA_META_KEY_VLAN_TAG (0x1UL << 28)
+ #define HWRM_PUSH32_DOORBELL_CFA_META_KEY_LAST \
+ HWRM_PUSH32_DOORBELL_CFA_META_KEY_VLAN_TAG
+ uint32_t data[25];
+ /*
+ * This is the data for the push packet. If the packet data does
+ * not fit in the first pass, data writing can continue at
+ * offset 4 of the doorbell for up to 4 additional passes for a
+ * total data size of 512B maximum.
+ */
+} __attribute__((packed));
+
+/* Doorbell Structures */
+/*
+ * Description: This is the RoCE 32b Doorbell format. The host writes this
+ * message format directly to byte offset 8 of the appropriate doorbell page.
+ */
+/* 64b Doorbell Format (8 bytes) */
+struct dbr_dbr {
+ uint32_t index;
+ /*
+ * This value is the index being written. For SQ, RQ, SRQ, this
+ * is the producer index and should be the queue index of the
+ * last WQE written plus 1. For CQ, this is the consumer index
+ * and should be the index of the last CQE processed plus 1.
+ */
+ #define HWRM_DBR_DBR_INDEX_MASK 0xfffffUL
+ #define HWRM_DBR_DBR_INDEX_SFT 0
+ #define HWRM_DBR_DBR_RESERVED12_MASK 0xfff00000UL
+ #define HWRM_DBR_DBR_RESERVED12_SFT 20
+ uint32_t type_xid;
+ /* This value identifies the type of doorbell being written. */
+ /*
+ * This value identifies the resource that the doorbell is
+ * intended to notify. For SQ and RQ, this is the QPID. For SRQ,
+ * this is the SID. For CQ, this is the CID. Bits [19:16] of
+ * this values must be zero for a SID value.
+ */
+ #define HWRM_DBR_DBR_XID_MASK 0xfffffUL
+ #define HWRM_DBR_DBR_XID_SFT 0
+ #define HWRM_DBR_DBR_RESERVED8_MASK 0xff00000UL
+ #define HWRM_DBR_DBR_RESERVED8_SFT 20
+ /* This value identifies the type of doorbell being written. */
+ #define HWRM_DBR_DBR_TYPE_MASK 0xf0000000UL
+ #define HWRM_DBR_DBR_TYPE_SFT 28
+ /*
+ * This is a SQ producer index update. It
+ * indicates one or more new entries have been
+ * written to the SQ for the QPID indicated on
+ * the xID field.
+ */
+ #define HWRM_DBR_DBR_TYPE_SQ (0x0UL << 28)
+ /*
+ * This is a RQ producer index update. It
+ * indicates one or more new entries have been
+ * written to the RQ for the QPID indicated on
+ * the xID field.
+ */
+ #define HWRM_DBR_DBR_TYPE_RQ (0x1UL << 28)
+ /*
+ * This is a SRQ producer index update. It
+ * indicates one or more new entries have been
+ * written to the SRQ for the SID indicated on
+ * the xID field.
+ */
+ #define HWRM_DBR_DBR_TYPE_SRQ (0x2UL << 28)
+ /*
+ * This doorbell command arms the SRQ async
+ * event. The xID field must identify the SID
+ * that is begin armed. The index field is will
+ * set the arm threshold such that a
+ * notification will be generated if less than
+ * that number or SRQ entries are posted.
+ */
+ #define HWRM_DBR_DBR_TYPE_SRQ_ARM (0x3UL << 28)
+ /*
+ * This is a CQ consumer index update. It
+ * indicates one or more entries have been
+ * processed off the CQ indicated on the xID
+ * field.
+ */
+ #define HWRM_DBR_DBR_TYPE_CQ (0x4UL << 28)
+ /*
+ * this is a CQ consumer index update that also
+ * arms the CQ for solicited events.
+ */
+ #define HWRM_DBR_DBR_TYPE_CQ_ARMSE (0x5UL << 28)
+ /*
+ * This is a CQ consumer index update that also
+ * arms the CQ for any new CQE.
+ */
+ #define HWRM_DBR_DBR_TYPE_CQ_ARMALL (0x6UL << 28)
+ /*
+ * This is a CQ arm enable message. This message
+ * must be sent from the privileged driver
+ * before a new CQ_ARMSE or CQ_ARMALL message
+ * will be accepted. This doorbell can only be
+ * sent from the privileged (first) doorbell
+ * page of a function.
+ */
+ #define HWRM_DBR_DBR_TYPE_CQ_ARMENA (0x7UL << 28)
+ /*
+ * This doorbell command enables the SRQ async
+ * event to be armed. This message must be setn
+ * from the privileged driver before a new
+ * SRQ_ARM message will be accepted. The xID
+ * field must identify the SID that is begin
+ * enabled for arm. This doorbell can only be
+ * sent from the privileged (first) doorbell
+ * page of a function.
+ */
+ #define HWRM_DBR_DBR_TYPE_SRQ_ARMENA (0x8UL << 28)
+ /*
+ * This doorbell command indicates that the
+ * cutoff CQE has been processed and the driver
+ * is now processing completions from the new
+ * CQ. The index field for this doorbell type
+ * must be zero.
+ */
+ #define HWRM_DBR_DBR_TYPE_CQ_CUTOFF_ACK (0x9UL << 28)
+ /*
+ * This doorbell command is used during doorbell
+ * moderation to consume system BW and help
+ * prevent doorbell FIFO overflow. All other
+ * fields should be zero for NULL doorbell.
+ */
+ #define HWRM_DBR_DBR_TYPE_NULL (0xfUL << 28)
+} __attribute__((packed));
+
+/* 32b Doorbell Format (4 bytes) */
+struct dbr_dbr32 {
+ uint32_t type_abs_incr_xid;
+ /* This value identifies the type of doorbell being written. */
+ /*
+ * This value identifies the resource that the doorbell is
+ * intended to notify. For SQ and RQ, this is the QPID. For SRQ,
+ * this is the SID. For CQ, this is the CID. Bits [19:16] of
+ * this values must be zero for a SID value.
+ */
+ #define HWRM_DBR_DBR32_XID_MASK 0xfffffUL
+ #define HWRM_DBR_DBR32_XID_SFT 0
+ #define HWRM_DBR_DBR32_RESERVED4_MASK 0xf00000UL
+ #define HWRM_DBR_DBR32_RESERVED4_SFT 20
+ /*
+ * When abs=0, this value is the value to add to the appropriate
+ * index value. When abs=1, this value is the new value for the
+ * index. Absolute value is used when the queue is being
+ * wrapped. When abs=1, the incr value follows the same rules as
+ * the index value in the 64b doorbell.
+ */
+ #define HWRM_DBR_DBR32_INCR_MASK 0xf000000UL
+ #define HWRM_DBR_DBR32_INCR_SFT 24
+ /* This value defines how the incr value will be interpreted. */
+ #define HWRM_DBR_DBR32_ABS 0x10000000UL
+ /* This value identifies the type of doorbell being written. */
+ #define HWRM_DBR_DBR32_TYPE_MASK 0xe0000000UL
+ #define HWRM_DBR_DBR32_TYPE_SFT 29
+ /*
+ * This is a SQ producer index update. It
+ * indicates one or more new entries have been
+ * written to the SQ for the QPID indicated on
+ * the xID field.
+ */
+ #define HWRM_DBR_DBR32_TYPE_SQ (0x0UL << 29)
+} __attribute__((packed));
+
+/* SQ WQE Structures */
+/*
+ * Description: This is the Bind WQE structure. This WQE can perform either: *
+ * type1 "bind memory window", if mw_type==Type1 * type2 "post send bind memory
+ * window", if mw_type==Type2
+ */
+/* Base SQ WQE (8 bytes) */
+struct sq_base {
+ uint8_t wqe_type;
+ /* This field defines the type of SQ WQE. */
+ /* Send */
+ #define HWRM_SQ_BASE_WQE_TYPE_SEND 0x0UL
+ /*
+ * Send with Immediate Allowed only on reliable
+ * connection (RC) and unreliable datagram (UD)
+ * SQ's.
+ */
+ #define HWRM_SQ_BASE_WQE_TYPE_SEND_W_IMMEAD 0x1UL
+ /*
+ * Send with Invalidate. Allowed only on
+ * reliable connection (RC) SQ's.
+ */
+ #define HWRM_SQ_BASE_WQE_TYPE_SEND_W_INVALID 0x2UL
+ /*
+ * RDMA Write. Allowed only on reliable
+ * connection (RC) SQ's.
+ */
+ #define HWRM_SQ_BASE_WQE_TYPE_WRITE_WQE 0x4UL
+ /*
+ * RDMA Write with Immediate. Allowed only on
+ * reliable connection (RC) SQ's.
+ */
+ #define HWRM_SQ_BASE_WQE_TYPE_WRITE_W_IMMEAD 0x5UL
+ /* RDMA Read. Allowed only on reliable connection (RC) SQ's. */
+ #define HWRM_SQ_BASE_WQE_TYPE_READ_WQE 0x6UL
+ /*
+ * Atomic Compare/Swap. Allowed only on reliable
+ * connection (RC) SQ's.
+ */
+ #define HWRM_SQ_BASE_WQE_TYPE_ATOMIC_CS 0x8UL
+ /*
+ * Atomic Fetch/Add. Allowed only on reliable
+ * connection (RC) SQ's.
+ */
+ #define HWRM_SQ_BASE_WQE_TYPE_ATOMIC_FA 0xbUL
+ /*
+ * Local Invalidate. Allowed only on reliable
+ * connection (RC) SQ's.
+ */
+ #define HWRM_SQ_BASE_WQE_TYPE_LOCAL_INVALID 0xcUL
+ /*
+ * FR-PMR (Fast Register Physical Memory Region)
+ * Allowed only on reliable connection (RC)
+ * SQ's.
+ */
+ #define HWRM_SQ_BASE_WQE_TYPE_FR_PMR 0xdUL
+ /*
+ * Memory Bind Allowed only on reliable
+ * connection (RC) SQ's.
+ */
+ #define HWRM_SQ_BASE_WQE_TYPE_BIND 0xeUL
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* WQE SGE (16 bytes) */
+struct sq_sge {
+ uint64_t va_or_pa;
+ /*
+ * The virtual address in local memory or a physical address
+ * when l_key value is a reserved value of a physical address.
+ * Driver configures this value in the chip and the chip
+ * compares l_key in SGEs with that reserved value, if equal it
+ * access the physical address specified. The chip however MUST
+ * verify that the QP allows the use reserved key.
+ */
+ uint32_t l_key;
+ /*
+ * Local Key associated with this registered MR; The 24 msb of
+ * the key used to index the MRW Table and the 8 lsb are
+ * compared with the 8 bits key part stored in the MRWC. The PBL
+ * in the MRW Context is used to translate the above VA to
+ * physical address.
+ */
+ uint32_t size;
+ /*
+ * Size of SGE in bytes; Based on page size of the system the
+ * chip knows how many entries are in the PBL
+ */
+} __attribute__((packed));
+
+/* PSN Search Structure (8 bytes) */
+struct sq_psn_search {
+ uint32_t opcode_start_psn;
+ /* The opcodes are software defined. */
+ /* Start PSN. */
+ #define HWRM_SQ_PSN_SEARCH_START_PSN_MASK 0xffffffUL
+ #define HWRM_SQ_PSN_SEARCH_START_PSN_SFT 0
+ /* The opcodes are software defined. */
+ #define HWRM_SQ_PSN_SEARCH_OPCODE_MASK 0xff000000UL
+ #define HWRM_SQ_PSN_SEARCH_OPCODE_SFT 24
+ uint32_t flags_next_psn;
+ /* Opcode specific flags. */
+ /* Next PSN. Equal to the start PSN of the next WQE. */
+ #define HWRM_SQ_PSN_SEARCH_NEXT_PSN_MASK 0xffffffUL
+ #define HWRM_SQ_PSN_SEARCH_NEXT_PSN_SFT 0
+ /* Opcode specific flags. */
+ #define HWRM_SQ_PSN_SEARCH_FLAGS_MASK 0xff000000UL
+ #define HWRM_SQ_PSN_SEARCH_FLAGS_SFT 24
+} __attribute__((packed));
+
+/* Send SQ WQE (40 bytes) */
+struct sq_send {
+ uint8_t wqe_type;
+ /* This field defines the type of SQ WQE. */
+ /* Send */
+ #define HWRM_SQ_SEND_WQE_TYPE_SEND 0x0UL
+ /*
+ * Send with Immediate Allowed only on reliable
+ * connection (RC) and unreliable datagram (UD)
+ * SQ's.
+ */
+ #define HWRM_SQ_SEND_WQE_TYPE_SEND_W_IMMEAD 0x1UL
+ /*
+ * Send with Invalidate. Allowed only on
+ * reliable connection (RC) SQ's.
+ */
+ #define HWRM_SQ_SEND_WQE_TYPE_SEND_W_INVALID 0x2UL
+ uint8_t flags;
+ /*
+ * Set if completion signaling is requested. If this bit is 0,
+ * and the SQ is configured to support Unsignaled completion the
+ * controller should not generate a CQE unless there was an
+ * error. This refers to the CQE on the sender side. (The se
+ * flag refers to the receiver side).
+ */
+ #define HWRM_SQ_SEND_FLAGS_SIGNAL_COMP 0x1UL
+ /*
+ * Indication to complete all previous RDMA Read or Atomic WQEs
+ * on the SQ before executing this WQE. This flag must be zero
+ * for a UD send.
+ */
+ #define HWRM_SQ_SEND_FLAGS_RD_OR_ATOMIC_FENCE 0x2UL
+ /*
+ * For local invalidate request. Indicate to complete all
+ * previous SQ's WQEs before executing this WQE. This flag must
+ * be zero for a UD send.
+ */
+ #define HWRM_SQ_SEND_FLAGS_UC_FENCE 0x4UL
+ /*
+ * Solicit event flag. Indication sent in BTH header to the
+ * receiver to generate a Completion Event Notification, i.e.
+ * CNQE. This bit should be set only in the last (or only)
+ * packet of the message.
+ */
+ #define HWRM_SQ_SEND_FLAGS_SE 0x8UL
+ /*
+ * Indicate that inline data is posted to the SQ in the data
+ * area of this WQE.
+ */
+ #define HWRM_SQ_SEND_FLAGS_INLINE 0x10UL
+ uint8_t wqe_size;
+ /*
+ * The number of 16 bytes chunks of data including this first
+ * word of the request that are a valid part of the request. The
+ * valid 16 bytes units other than the WQE structure can be SGEs
+ * (Scatter Gather Elements) OR inline data. While this field
+ * defines the valid WQE size. The actual total WQE size is
+ * always 128B.
+ */
+ uint8_t reserved8_1;
+ uint32_t inv_key_or_imm_data;
+ /*
+ * Either invalidate key (R_Key of the remote host) that will be
+ * send with IETH (Invalidate ETH) if wqe_type is of Send with
+ * Invalidate, or immediate value that will be sent with ImmDt
+ * header if wqe_type is Send with Immediate.
+ */
+ uint32_t length;
+ /* This field represents a 32-bit total data length, in bytes. */
+ uint32_t q_key;
+ /*
+ * When in the SQ of a UD QP, indicates the q_key to be used in
+ * the transmitted packet. However, if the most significant bit
+ * of this field is set, then the q_key will be taken from QP
+ * context, rather than from this field. When in the SQ of a
+ * non-UD QP, this field is reserved and should be filled with
+ * zeros.
+ */
+ uint32_t dst_qp;
+ /*
+ * When in the SQ of a UD QP, indicates the destination QP to be
+ * used in the transmitted packet. When in the SQ of a non-UD
+ * QP, this field is reserved and should be filled with zeros.
+ */
+ #define HWRM_SQ_SEND_DST_QP_MASK 0xffffffUL
+ #define HWRM_SQ_SEND_DST_QP_SFT 0
+ #define HWRM_SQ_SEND_RESERVED8_2_MASK 0xff000000UL
+ #define HWRM_SQ_SEND_RESERVED8_2_SFT 24
+ uint32_t avid;
+ /* This field is reserved for future expansion of the AVID. */
+ /*
+ * If the serv_type is 'UD', then this field supplies the AVID
+ * (Address Vector ID).
+ */
+ #define HWRM_SQ_SEND_AVID_MASK 0xfffffUL
+ #define HWRM_SQ_SEND_AVID_SFT 0
+ /* This field is reserved for future expansion of the AVID. */
+ #define HWRM_SQ_SEND_RESERVED_AVID_MASK 0xfff00000UL
+ #define HWRM_SQ_SEND_RESERVED_AVID_SFT 20
+ uint64_t reserved64;
+ uint32_t data[24];
+ /*
+ * When inline=0, then this area is filled with from 1 to 6 SGEs
+ * based on the wqe_size field. When inline=1, this area is
+ * filled with payload data for the send based on the
+ * length_or_AVID field. Bits [7:0] of word 0 hold the first
+ * byte to go out on the wire.
+ */
+} __attribute__((packed));
+
+/* Send Raw Ethernet and QP1 SQ WQE (40 bytes) */
+struct sq_send_raweth_qp1 {
+ uint8_t wqe_type;
+ /* This field defines the type of SQ WQE. */
+ /* Send */
+ #define HWRM_SQ_SEND_RAWETH_QP1_WQE_TYPE_SEND 0x0UL
+ uint8_t flags;
+ /*
+ * Set if completion signaling is requested. If this bit is 0,
+ * and the SQ is configured to support Unsignaled completion the
+ * controller should not generate a CQE unless there was an
+ * error. This refers to the CQE on the sender side. (The se
+ * flag refers to the receiver side).
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_FLAGS_SIGNAL_COMP 0x1UL
+ /* This flag must be zero for a Raweth or QP1 send. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_FLAGS_RD_OR_ATOMIC_FENCE 0x2UL
+ /* This flag must be zero for a Raweth or QP1 send. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_FLAGS_UC_FENCE 0x4UL
+ /* This flag must be zero for a Raweth or QP1 send. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_FLAGS_SE 0x8UL
+ /*
+ * Indicate that inline data is posted to the SQ in the data
+ * area of this WQE.
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_FLAGS_INLINE 0x10UL
+ uint8_t wqe_size;
+ /*
+ * The number of 16 bytes chunks of data including this first
+ * word of the request that are a valid part of the request. The
+ * valid 16 bytes units other than the WQE structure can be SGEs
+ * (Scatter Gather Elements) OR inline data. While this field
+ * defines the valid WQE size. The actual total WQE size is
+ * always 128B.
+ */
+ uint8_t reserved8;
+ uint16_t lflags;
+ /*
+ * All bits in this field must be valid on the first BD of a
+ * packet. Their value on other BDs of the packet will be
+ * ignored.
+ */
+ /*
+ * If set to 1, the controller replaces the TCP/UPD checksum
+ * fields of normal TCP/UPD checksum, or the inner TCP/UDP
+ * checksum field of the encapsulated TCP/UDP packets with the
+ * hardware calculated TCP/UDP checksum for the packet
+ * associated with this descriptor. This bit must be valid on
+ * the first BD of a packet.
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_LFLAGS_TCP_UDP_CHKSUM 0x1UL
+ /*
+ * If set to 1, the controller replaces the IP checksum of the
+ * normal packets, or the inner IP checksum of the encapsulated
+ * packets with the hardware calculated IP checksum for the
+ * packet associated with this descriptor. This bit must be
+ * valid on the first BD of a packet.
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_LFLAGS_IP_CHKSUM 0x2UL
+ /*
+ * If set to 1, the controller will not append an Ethernet CRC
+ * to the end of the frame. This bit must be valid on the first
+ * BD of a packet. Packet must be 64B or longer when this flag
+ * is set. It is not usefull to use this bit with any form of TX
+ * offload such as CSO or LSO. The intent is that the packet
+ * from the host already has a valid Ethernet CRC on the packet.
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_LFLAGS_NOCRC 0x4UL
+ /*
+ * If set to 1, the device will record the time at which the
+ * packet was actually transmitted at the TX MAC. This bit must
+ * be valid on the first BD of a packet.
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_LFLAGS_STAMP 0x8UL
+ /*
+ * If set to 1, The controller replaces the tunnel IP checksum
+ * field with hardware calculated IP checksum for the IP header
+ * of the packet associated with this descriptor. In case of
+ * VXLAN, the controller also replaces the outer header UDP
+ * checksum with hardware calculated UDP checksum for the packet
+ * associated with this descriptor.
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_LFLAGS_T_IP_CHKSUM 0x10UL
+ /* This bit is reserved and should be zero. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_LFLAGS_RESERVED1_1 0x20UL
+ /* This bit is reserved and should be zero. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_LFLAGS_RESERVED1_2 0x40UL
+ /* This bit is reserved and should be zero. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_LFLAGS_RESERVED1_3 0x80UL
+ /*
+ * If set to '1', then the RoCE ICRC will be appended to the
+ * packet. Packet must be a valid RoCE format packet.
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_LFLAGS_ROCE_CRC 0x100UL
+ /*
+ * If set to '1', then the FCoE CRC will be appended to the
+ * packet. Packet must be a valid FCoE format packet.
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_LFLAGS_FCOE_CRC 0x200UL
+ uint16_t cfa_action;
+ /*
+ * This value selects a CFA action to perform on the packet. Set
+ * this value to zero if no CFA action is desired. This value
+ * must be valid on the first BD of a packet.
+ */
+ uint32_t length;
+ /*
+ * This field represents a 32-bit total data length, in bytes.
+ * Note, however, that the length cannot exceed the MTU.
+ */
+ uint32_t reserved32_1;
+ uint32_t cfa_meta;
+ /*
+ * This value is action meta-data that defines CFA edit
+ * operations that are done in addition to any action editing.
+ */
+ /* When key=1, This is the VLAN tag VID value. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_VID_MASK 0xfffUL
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_VID_SFT 0
+ /* When key=1, This is the VLAN tag DE value. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_DE 0x1000UL
+ /* When key=1, This is the VLAN tag PRI value. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_PRI_MASK 0xe000UL
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_PRI_SFT 13
+ /* When key=1, This is the VLAN tag TPID select value. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_TPID_MASK 0x70000UL
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_TPID_SFT 16
+ /* 0x88a8 */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_TPID_TPID88A8 \
+ (0x0UL << 16)
+ /* 0x8100 */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_TPID_TPID8100 \
+ (0x1UL << 16)
+ /* 0x9100 */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_TPID_TPID9100 \
+ (0x2UL << 16)
+ /* 0x9200 */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_TPID_TPID9200 \
+ (0x3UL << 16)
+ /* 0x9300 */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_TPID_TPID9300 \
+ (0x4UL << 16)
+ /* Value programmed in CFA VLANTPID register. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_TPID_TPIDCFG (0x5UL << 16)
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_TPID_LAST \
+ SQ_SEND_RAWETH_QP1_CFA_META_VLAN_TPID_TPIDCFG
+ /* When key=1, This is the VLAN tag TPID select value. */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_RESERVED_MASK 0xff80000UL
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_VLAN_RESERVED_SFT 19
+ /*
+ * This field identifies the type of edit to be performed on the
+ * packet. This value must be valid on the first BD of a packet.
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_KEY_MASK 0xf0000000UL
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_KEY_SFT 28
+ /* No editing */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_KEY_NONE (0x0UL << 28)
+ /*
+ * - meta[17:16] - TPID select value (0 =
+ * 0x8100). - meta[15:12] - PRI/DE value. -
+ * meta[11:0] - VID value.
+ */
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_KEY_VLAN_TAG (0x1UL << 28)
+ #define HWRM_SQ_SEND_RAWETH_QP1_CFA_META_KEY_LAST \
+ SQ_SEND_RAWETH_QP1_CFA_META_KEY_VLAN_TAG
+ uint32_t reserved32_2;
+ uint64_t reserved64;
+ uint32_t data[24];
+ /*
+ * When inline=0, then this area is filled with from 1 to 6 SGEs
+ * based on the wqe_size field. When inline=1, this area is
+ * filled with payload data for the send based on the
+ * length_or_AVID field. Bits [7:0] of word 0 hold the first
+ * byte to go out on the wire.
+ */
+} __attribute__((packed));
+
+/* RDMA SQ WQE (40 bytes) */
+struct sq_rdma {
+ uint8_t wqe_type;
+ /* This field defines the type of SQ WQE. */
+ /*
+ * RDMA Write. Allowed only on reliable
+ * connection (RC) SQ's.
+ */
+ #define HWRM_SQ_RDMA_WQE_TYPE_WRITE_WQE 0x4UL
+ /*
+ * RDMA Write with Immediate. Allowed only on
+ * reliable connection (RC) SQ's.
+ */
+ #define HWRM_SQ_RDMA_WQE_TYPE_WRITE_W_IMMEAD 0x5UL
+ /* RDMA Read. Allowed only on reliable connection (RC) SQ's. */
+ #define HWRM_SQ_RDMA_WQE_TYPE_READ_WQE 0x6UL
+ uint8_t flags;
+ /*
+ * Set if completion signaling is requested. If this bit is 0,
+ * and the SQ is configured to support Unsignaled completion the
+ * controller should not generate a CQE unless there was an
+ * error. This refer to CQE on the sender side (se_flag refer to
+ * the receiver side)
+ */
+ #define HWRM_SQ_RDMA_FLAGS_SIGNAL_COMP 0x1UL
+ /*
+ * Indication to complete all previous RDMA Read or Atomic WQEs
+ * on the SQ before executing this WQE
+ */
+ #define HWRM_SQ_RDMA_FLAGS_RD_OR_ATOMIC_FENCE 0x2UL
+ /*
+ * Unconditional fence. Indicate to complete all previous SQ's
+ * WQEs before executing this WQE.
+ */
+ #define HWRM_SQ_RDMA_FLAGS_UC_FENCE 0x4UL
+ /*
+ * Solicit event. Indication sent in BTH header to the receiver
+ * to generate a Completion Event Notification, i.e. CNQE. This
+ * bit should be set only in the last (or only) packet of the
+ * message.
+ */
+ #define HWRM_SQ_RDMA_FLAGS_SE 0x8UL
+ /*
+ * Indicate that inline data is posted to the SQ following this
+ * WQE. This bit may be 1 only for write operations.
+ */
+ #define HWRM_SQ_RDMA_FLAGS_INLINE 0x10UL
+ uint8_t wqe_size;
+ /*
+ * The number of 16 bytes chunks of data including this first
+ * wqe of the request that are a valid part of the request. The
+ * valid 16 bytes units other than the WQE structure can be SGEs
+ * (Scatter Gather Elements) OR inline data. While this field
+ * defines the valid WQE size. The actual total WQE size is
+ * always 128B.
+ */
+ uint8_t reserved8;
+ uint32_t imm_data;
+ /*
+ * Immediate data - valid for RDMA Write with immediate and
+ * causes the controller to add immDt header with this value
+ */
+ uint32_t length;
+ /* Total data length in bytes */
+ uint32_t reserved32_1;
+ uint64_t remote_va;
+ /* Remote VA sent to the destination QP */
+ uint32_t remote_key;
+ /*
+ * R_Key provided by remote node when the connection was
+ * established and placed in the RETH header. It identify the
+ * MRW on the remote host
+ */
+ uint32_t reserved32_2;
+ uint32_t data[24];
+ /*
+ * When inline=0, then this area is filled with from 1 to 6 SGEs
+ * based on the wqe_size field. When inline=1, this area is
+ * filled with payload data for the write based on the length
+ * field. Bits [7:0] of word 0 hold the first byte to go out on
+ * the wire.
+ */
+} __attribute__((packed));
+
+/* Atomic SQ WQE (40 bytes) */
+struct sq_atomic {
+ uint8_t wqe_type;
+ /* This field defines the type of SQ WQE. */
+ /*
+ * Atomic Compare/Swap. Allowed only on reliable
+ * connection (RC) SQ's.
+ */
+ #define HWRM_SQ_ATOMIC_WQE_TYPE_ATOMIC_CS 0x8UL
+ /*
+ * Atomic Fetch/Add. Allowed only on reliable
+ * connection (RC) SQ's.
+ */
+ #define HWRM_SQ_ATOMIC_WQE_TYPE_ATOMIC_FA 0xbUL
+ uint8_t flags;
+ /*
+ * Set if completion signaling is requested. If this bit is 0,
+ * and the SQ is configured to support Unsignaled completion the
+ * controller should not generate a CQE unless there was an
+ * error. This refer to CQE on the sender side (se_flag refer to
+ * the receiver side)
+ */
+ #define HWRM_SQ_ATOMIC_FLAGS_SIGNAL_COMP 0x1UL
+ /*
+ * Indication to complete all previous RDMA Read or Atomic WQEs
+ * on the SQ before executing this WQE
+ */
+ #define HWRM_SQ_ATOMIC_FLAGS_RD_OR_ATOMIC_FENCE 0x2UL
+ /*
+ * Unconditional fence. Indicate to complete all previous SQ's
+ * WQEs before executing this WQE.
+ */
+ #define HWRM_SQ_ATOMIC_FLAGS_UC_FENCE 0x4UL
+ /*
+ * Solicit event. Indication sent in BTH header to the receiver
+ * to generate a Completion Event Notification, i.e. CNQE. This
+ * bit should be set only in the last (or only) packet of the
+ * message.
+ */
+ #define HWRM_SQ_ATOMIC_FLAGS_SE 0x8UL
+ /* NA for this WQE. */
+ #define HWRM_SQ_ATOMIC_FLAGS_INLINE 0x10UL
+ uint16_t reserved16;
+ uint32_t remote_key;
+ /*
+ * R_Key provided by remote node when the connection was
+ * established and placed in the AETH header. It identify the
+ * MRW on the remote host
+ */
+ uint64_t remote_va;
+ /* Remote VA sent to the destination QP */
+ uint64_t swap_data;
+ /* Data value to be placed in remote host specified address */
+ uint64_t cmp_data;
+ /*
+ * Data value to be compared with the value in the remote host
+ * specified address
+ */
+ uint32_t data[24];
+ /*
+ * The first 16B of the data field must be filled with a single
+ * SGE. This will be used to store the return value from the
+ * Atomic Ack response. The size of the single SGE must be 8B.
+ */
+} __attribute__((packed));
+
+/* Local Invalidate SQ WQE (40 bytes) */
+struct sq_localinvalidate {
+ uint8_t wqe_type;
+ /* This field defines the type of SQ WQE. */
+ /*
+ * Local Invalidate. Allowed only on reliable
+ * connection (RC) SQ's.
+ */
+ #define HWRM_SQ_LOCALINVALIDATE_WQE_TYPE_LOCAL_INVALID 0xcUL
+ uint8_t flags;
+ /*
+ * Set if completion signaling is requested. If this bit is 0,
+ * and the SQ is configured to support Unsignaled completion the
+ * controller should not generate a CQE unless there was an
+ * error. This refer to CQE on the sender side (se_flag refer to
+ * the receiver side)
+ */
+ #define HWRM_SQ_LOCALINVALIDATE_FLAGS_SIGNAL_COMP 0x1UL
+ /*
+ * Indication to complete all previous RDMA Read or Atomic WQEs
+ * on the SQ before executing this WQE
+ */
+ #define HWRM_SQ_LOCALINVALIDATE_FLAGS_RD_OR_ATOMIC_FENCE 0x2UL
+ /*
+ * Unconditional fence. Indicate to complete all previous SQ's
+ * WQEs before executing this WQE.
+ */
+ #define HWRM_SQ_LOCALINVALIDATE_FLAGS_UC_FENCE 0x4UL
+ /*
+ * Solicit event. Indication sent in BTH header to the receiver
+ * to generate a Completion Event Notification, i.e. CNQE. This
+ * bit should be set only in the last (or only) packet of the
+ * message.
+ */
+ #define HWRM_SQ_LOCALINVALIDATE_FLAGS_SE 0x8UL
+ /* NA for this WQE */
+ #define HWRM_SQ_LOCALINVALIDATE_FLAGS_INLINE 0x10UL
+ uint16_t reserved16;
+ uint32_t inv_l_key;
+ /*
+ * The local key for the MR/W to invalidate; 24 msb of the key
+ * are used to index the MRW table, 8 lsb are compared with the
+ * 8 bit key in the MRWC
+ */
+ uint64_t reserved64;
+ uint32_t reserved128[4];
+ uint32_t data[24];
+ /* The data field for local invalidate is not used. */
+} __attribute__((packed));
+
+/* FR-PMR SQ WQE (40 bytes) */
+struct sq_fr_pmr {
+ uint8_t wqe_type;
+ /* This field defines the type of SQ WQE. */
+ /*
+ * FR-PMR (Fast Register Physical Memory Region)
+ * Allowed only on reliable connection (RC)
+ * SQ's.
+ */
+ #define HWRM_SQ_FR_PMR_WQE_TYPE_FR_PMR 0xdUL
+ uint8_t flags;
+ /*
+ * Set if completion signaling is requested. If this bit is 0,
+ * and the SQ is configured to support Unsignaled completion the
+ * controller should not generate a CQE unless there was an
+ * error. This refer to CQE on the sender side (se_flag refer to
+ * the receiver side)
+ */
+ #define HWRM_SQ_FR_PMR_FLAGS_SIGNAL_COMP 0x1UL
+ /*
+ * Indication to complete all previous RDMA Read or Atomic WQEs
+ * on the SQ before executing this WQE
+ */
+ #define HWRM_SQ_FR_PMR_FLAGS_RD_OR_ATOMIC_FENCE 0x2UL
+ /*
+ * Unconditional fence. Indicate to complete all previous SQ's
+ * WQEs before executing this WQE.
+ */
+ #define HWRM_SQ_FR_PMR_FLAGS_UC_FENCE 0x4UL
+ /* Not Applicable for FR_PMR. Nothing is sent */
+ #define HWRM_SQ_FR_PMR_FLAGS_SE 0x8UL
+ /* NA. */
+ #define HWRM_SQ_FR_PMR_FLAGS_INLINE 0x10UL
+ uint8_t access_cntl;
+ /*
+ * This is the new access control for the MR. '1' means the
+ * operation is allowed. '0' means operation is not allowed.
+ */
+ /* Local Write Access */
+ #define HWRM_SQ_FR_PMR_ACCESS_CNTL_LOCAL_WRITE 0x1UL
+ /* Remote Read Access */
+ #define HWRM_SQ_FR_PMR_ACCESS_CNTL_REMOTE_READ 0x2UL
+ /* Remote Write Access */
+ #define HWRM_SQ_FR_PMR_ACCESS_CNTL_REMOTE_WRITE 0x4UL
+ /* Remote Atomic Access */
+ #define HWRM_SQ_FR_PMR_ACCESS_CNTL_REMOTE_ATOMIC 0x8UL
+ /* Window Binding Allowed */
+ #define HWRM_SQ_FR_PMR_ACCESS_CNTL_WINDOW_BIND 0x10UL
+ uint8_t zero_based_page_size_log;
+ /* 0 for 4KB page size, ... to 8GB */
+ #define HWRM_SQ_FR_PMR_PAGE_SIZE_LOG_MASK 0x1fUL
+ #define HWRM_SQ_FR_PMR_PAGE_SIZE_LOG_SFT 0
+ /* Page size is 4KB. */
+ #define HWRM_SQ_FR_PMR_PAGE_SIZE_LOG_PGSZ_4K 0x0UL
+ /* Page size is 8KB. */
+ #define HWRM_SQ_FR_PMR_PAGE_SIZE_LOG_PGSZ_8K 0x1UL
+ /* Page size is 64KB. */
+ #define HWRM_SQ_FR_PMR_PAGE_SIZE_LOG_PGSZ_64K 0x4UL
+ /* Page size is 256KB. */
+ #define HWRM_SQ_FR_PMR_PAGE_SIZE_LOG_PGSZ_256K 0x6UL
+ /* Page size is 1MB. */
+ #define HWRM_SQ_FR_PMR_PAGE_SIZE_LOG_PGSZ_1M 0x8UL
+ /* Page size is 2MB. */
+ #define HWRM_SQ_FR_PMR_PAGE_SIZE_LOG_PGSZ_2M 0x9UL
+ /* Page size is 4MB. */
+ #define HWRM_SQ_FR_PMR_PAGE_SIZE_LOG_PGSZ_4M 0xaUL
+ /* Page size is 1GB. */
+ #define HWRM_SQ_FR_PMR_PAGE_SIZE_LOG_PGSZ_1G 0x12UL
+ /* Indicate the MR is ZBVA (Zero Base VA) */
+ #define HWRM_SQ_FR_PMR_ZERO_BASED 0x20UL
+ #define HWRM_SQ_FR_PMR_RESERVED2_MASK 0xc0UL
+ #define HWRM_SQ_FR_PMR_RESERVED2_SFT 6
+ uint32_t l_key;
+ /*
+ * Local Key; 24 msb of the key are used to index the MRW table,
+ * 8 lsb are assigned to the 8 bit key_lsb field in the MRWC.
+ */
+ uint8_t length[5];
+ /* Length in bytes of registered MR */
+ uint8_t reserved8_1;
+ uint8_t reserved8_2;
+ uint8_t numlevels_pbl_page_size_log;
+ /* Number of levels of PBL for translation */
+ /* PBL page size. 0 for 4KB page size. */
+ #define HWRM_SQ_FR_PMR_PBL_PAGE_SIZE_LOG_MASK 0x1fUL
+ #define HWRM_SQ_FR_PMR_PBL_PAGE_SIZE_LOG_SFT 0
+ /* Page size is 4KB. */
+ #define HWRM_SQ_FR_PMR_PBL_PAGE_SIZE_LOG_PGSZ_4K 0x0UL
+ /* Page size is 8KB. */
+ #define HWRM_SQ_FR_PMR_PBL_PAGE_SIZE_LOG_PGSZ_8K 0x1UL
+ /* Page size is 64KB. */
+ #define HWRM_SQ_FR_PMR_PBL_PAGE_SIZE_LOG_PGSZ_64K 0x4UL
+ /* Page size is 256KB. */
+ #define HWRM_SQ_FR_PMR_PBL_PAGE_SIZE_LOG_PGSZ_256K 0x6UL
+ /* Page size is 1MB. */
+ #define HWRM_SQ_FR_PMR_PBL_PAGE_SIZE_LOG_PGSZ_1M 0x8UL
+ /* Page size is 2MB. */
+ #define HWRM_SQ_FR_PMR_PBL_PAGE_SIZE_LOG_PGSZ_2M 0x9UL
+ /* Page size is 4MB. */
+ #define HWRM_SQ_FR_PMR_PBL_PAGE_SIZE_LOG_PGSZ_4M 0xaUL
+ /* Page size is 1GB. */
+ #define HWRM_SQ_FR_PMR_PBL_PAGE_SIZE_LOG_PGSZ_1G 0x12UL
+ #define HWRM_SQ_FR_PMR_RESERVED1 0x20UL
+ /* Number of levels of PBL for translation */
+ #define HWRM_SQ_FR_PMR_NUMLEVELS_MASK 0xc0UL
+ #define HWRM_SQ_FR_PMR_NUMLEVELS_SFT 6
+ /*
+ * A zero level PBL means that the VA is the
+ * physical address used for the operation. No
+ * translation is done by the PTU.
+ */
+ #define HWRM_SQ_FR_PMR_NUMLEVELS_PHYSICAL (0x0UL << 6)
+ /*
+ * A one layer translation is provided between
+ * the logical and physical address. The PBL
+ * points to a physical page that contains PBE
+ * values that point to actual pg_size physical
+ * pages.
+ */
+ #define HWRM_SQ_FR_PMR_NUMLEVELS_LAYER1 (0x1UL << 6)
+ /*
+ * A two layer translation is provided between
+ * the logical and physical address. The PBL
+ * points to a physical page that contains PDE
+ * values that in turn point to pbl_pg_size
+ * physical pages that contain PBE values that
+ * point to actual physical pages.
+ */
+ #define HWRM_SQ_FR_PMR_NUMLEVELS_LAYER2 (0x2UL << 6)
+ uint64_t pblptr;
+ /* Pointer to the PBL, or PDL depending on number of levels */
+ uint64_t va;
+ /* Local Virtual Address */
+ uint32_t data[24];
+ /* The data field for FR-PRM is not used. */
+} __attribute__((packed));
+
+/* Bind SQ WQE (40 bytes) */
+struct sq_bind {
+ uint8_t wqe_type;
+ /* This field defines the type of SQ WQE. */
+ /*
+ * Memory Bind Allowed only on reliable
+ * connection (RC) SQ's.
+ */
+ #define HWRM_SQ_BIND_WQE_TYPE_BIND 0xeUL
+ uint8_t flags;
+ /*
+ * Set if completion signaling is requested. If this bit is 0,
+ * and the SQ is configured to support Unsignaled completion the
+ * controller should not generate a CQE unless there was an
+ * error. This refer to CQE on the sender side (se_flag refer to
+ * the receiver side)
+ */
+ #define HWRM_SQ_BIND_FLAGS_SIGNAL_COMP 0x1UL
+ /*
+ * Indication to complete all previous RDMA Read or Atomic WQEs
+ * on the SQ before executing this WQE
+ */
+ #define HWRM_SQ_BIND_FLAGS_RD_OR_ATOMIC_FENCE 0x2UL
+ /*
+ * Unconditional fence. Indicate to complete all previous SQ's
+ * WQEs before executing this WQE.
+ */
+ #define HWRM_SQ_BIND_FLAGS_UC_FENCE 0x4UL
+ /* NA, nothing is sent. */
+ #define HWRM_SQ_BIND_FLAGS_SE 0x8UL
+ /* NA */
+ #define HWRM_SQ_BIND_FLAGS_INLINE 0x10UL
+ uint8_t access_cntl;
+ /*
+ * This is the new access control for the MR. '1' means the
+ * operation is allowed. '0' means operation is not allowed.
+ */
+ /*
+ * Local Write Access. Local accesses are never allowed for
+ * memory windows, so this bit must always be zero in a bind
+ * WQE. If this bit is ever set, the bind will fail with an
+ * errored completion.
+ */
+ #define HWRM_SQ_BIND_ACCESS_CNTL_LOCAL_WRITE 0x1UL
+ /* Remote Read Access */
+ #define HWRM_SQ_BIND_ACCESS_CNTL_REMOTE_READ 0x2UL
+ /*
+ * Remote Write Access. Note that, if this bit is set, then the
+ * parent region to which the window is being bound must allow
+ * local writes. If this is not the case, then the bind will
+ * fail with an errored completion.
+ */
+ #define HWRM_SQ_BIND_ACCESS_CNTL_REMOTE_WRITE 0x4UL
+ /*
+ * Remote Atomic Access. Note that, if this bit is set, then the
+ * parent region to which the window is being bound must allow
+ * local writes. If this is not the case, then the bind will
+ * fail with an errored completion.
+ */
+ #define HWRM_SQ_BIND_ACCESS_CNTL_REMOTE_ATOMIC 0x8UL
+ /*
+ * Window Binding Allowed. It is never allowed to bind windows
+ * to windows, so this bit must always be zero in a bind WQE. If
+ * this bit is ever set, the bind will fail with an errored
+ * completion.
+ */
+ #define HWRM_SQ_BIND_ACCESS_CNTL_WINDOW_BIND 0x10UL
+ uint8_t reserved8_1;
+ /* reserved8_1 is 8 b */
+ uint8_t mw_type_zero_based;
+ /*
+ * If this bit is set, then the newly-bound memory window will
+ * be zero-based. If clear, then the newly-bound memory window
+ * will be non-zero-based.
+ */
+ #define HWRM_SQ_BIND_ZERO_BASED 0x1UL
+ /*
+ * If type1 is specified, then this WQE performs a "bind memory
+ * window" operation on a type1 window. If type2 is specified,
+ * then this WQE performs a "post send bind memory window"
+ * operation on a type2 window. Note that the bind WQE cannot
+ * change the type of the memory window. If a "bind memory
+ * window" operation is attempted on a memory window that was
+ * allocated as type2, then the bind will fail with an errored
+ * completion, as "bind memory window" is allowed only on type1
+ * memory windows. Similarly, if a "post send bind memory
+ * window" operation is attempted on a memory window that was
+ * allocated as type1, then the bind will fail with an errored
+ * completions, as "post send bind memory window" is allowed
+ * only on type2 memory windows.
+ */
+ #define HWRM_SQ_BIND_MW_TYPE 0x2UL
+ /* Type 1 Bind Memory Window */
+ #define HWRM_SQ_BIND_MW_TYPE_TYPE1 (0x0UL << 1)
+ /* Type 2 Post Send Bind Memory Window */
+ #define HWRM_SQ_BIND_MW_TYPE_TYPE2 (0x1UL << 1)
+ #define HWRM_SQ_BIND_RESERVED6_MASK 0xfcUL
+ #define HWRM_SQ_BIND_RESERVED6_SFT 2
+ uint8_t reserved8_2;
+ uint16_t reserved16;
+ uint32_t parent_l_key;
+ /*
+ * The L_Key of the parent MR; 24 msb of the key are used to
+ * index the MRW table, 8 lsb are compared with the 8 bit key in
+ * the MRWC.
+ */
+ uint32_t l_key;
+ /*
+ * Local Key; 24 msb of the key are used to index the memory
+ * window being bound in the MRW table, 8 lsb are assign to the
+ * 8 bit key_lsb field in the MRWC.
+ */
+ uint64_t va;
+ /* Local Virtual Address */
+ uint8_t length[5];
+ /*
+ * Length in bytes of registered MW; 40 bits as this is the max
+ * size of an MR/W
+ */
+ uint8_t data_reserved24[99];
+ /* The data field for Bind is not used. */
+ #define HWRM_SQ_BIND_RESERVED24_MASK 0xffffff00UL
+ #define HWRM_SQ_BIND_RESERVED24_SFT 8
+ /* The data field for Bind is not used. */
+ #define HWRM_SQ_BIND_DATA_MASK 0xffffffffUL
+ #define HWRM_SQ_BIND_DATA_SFT 0
+} __attribute__((packed));
+
+/* RQ/SRQ WQE Structures */
+/* Description: This is the RQ/SRQ WQE structure. */
+/* RQ/SRQ WQE (40 bytes) */
+struct rq_wqe {
+ uint8_t wqe_type;
+ /* wqe_type is 8 b */
+ /*
+ * RQ/SRQ WQE. This WQE is used for posting
+ * buffers on an RQ or SRQ.
+ */
+ #define HWRM_RQ_WQE_WQE_TYPE_RCV 0x80UL
+ uint8_t flags;
+ /* No flags supported for this WQE type. */
+ uint8_t wqe_size;
+ /*
+ * Specify the total number 16B chunks that make up the valid
+ * portion of the WQE. This includes the first chunk that is the
+ * WQE structure and up to 6 SGE structures. While the valid
+ * area is defined by the wqe_size field, the actual WQE size is
+ * fixed at 128B.
+ */
+ uint8_t reserved8;
+ uint32_t reserved32;
+ uint32_t wr_id[2];
+ /*
+ * Opaque value used by upper layer SW to identify the id of the
+ * WR which generated the WQE. Used in CQE. Valid in the first
+ * SGE of an SRQ WQE.
+ */
+ #define HWRM_RQ_WQE_WR_ID_MASK 0xfffffUL
+ #define HWRM_RQ_WQE_WR_ID_SFT 0
+ #define HWRM_RQ_WQE_RESERVED44_MASK 0xfff00000UL
+ #define HWRM_RQ_WQE_RESERVED44_SFT 20
+ uint32_t reserved128[4];
+ uint32_t data[24];
+ /*
+ * The data field for RQ WQE is filled with from 1 to 6 SGE
+ * structures as defined by the wqe_size field.
+ */
+} __attribute__((packed));
+
+/* CQ CQE Structures */
+/* Description: This is the Cutoff CQE structure. */
+/* Base CQE (32 bytes) */
+struct cq_base {
+ uint64_t reserved64_1;
+ uint64_t reserved64_2;
+ uint64_t reserved64_3;
+ uint8_t cqe_type_toggle;
+ /*
+ * Indicate valid completion - written by the chip. Cumulus
+ * toggle this bit each time it finished consuming all PBL
+ * entries
+ */
+ #define HWRM_CQ_BASE_TOGGLE 0x1UL
+ /* This field defines the type of SQ WQE. */
+ #define HWRM_CQ_BASE_CQE_TYPE_MASK 0x1eUL
+ #define HWRM_CQ_BASE_CQE_TYPE_SFT 1
+ /*
+ * Requester completion - This is used for both
+ * RC and UD SQ completions.
+ */
+ #define HWRM_CQ_BASE_CQE_TYPE_INPUT (0x0UL << 1)
+ /*
+ * Responder RC Completion - This is used for
+ * both RQ and SRQ completions for RC service
+ * QPs.
+ */
+ #define HWRM_CQ_BASE_CQE_TYPE_RES_RC (0x1UL << 1)
+ /*
+ * Responder UD Completion - This is used for
+ * both RQ and SRQ completion for UD service
+ * QPs.
+ */
+ #define HWRM_CQ_BASE_CQE_TYPE_RES_UD (0x2UL << 1)
+ /*
+ * Responder RawEth and QP1 Completion - This is
+ * used for RQ completion for RawEth service and
+ * QP1 service QPs.
+ */
+ #define HWRM_CQ_BASE_CQE_TYPE_RES_RAWETH_QP1 (0x3UL << 1)
+ /*
+ * Terminal completion - This is used to
+ * indicate that no further completions will be
+ * made for this QP on this CQ.
+ */
+ #define HWRM_CQ_BASE_CQE_TYPE_TERMINAL (0xeUL << 1)
+ /* Cut off CQE; for CQ resize see CQ and SRQ Resize */
+ #define HWRM_CQ_BASE_CQE_TYPE_CUT_OFF (0xfUL << 1)
+ #define HWRM_CQ_BASE_RESERVED3_MASK 0xe0UL
+ #define HWRM_CQ_BASE_RESERVED3_SFT 5
+ uint8_t status;
+ /* This field indicates the status for the CQE. */
+ uint16_t reserved16;
+ uint32_t reserved32;
+} __attribute__((packed));
+
+/* Requester CQ CQE (32 bytes) */
+struct cq_req {
+ uint64_t qp_handle;
+ /*
+ * This is an application level ID used to identify the QP and
+ * its SQ and RQ.
+ */
+ uint16_t sq_cons_idx;
+ /*
+ * SQ Consumer Index - points to the entry just past the last
+ * WQE that has been completed by the chip. Wraps around at
+ * QPC.sq_size (i.e. the valid range of the SQ Consumer Index is
+ * 0 to (QPC.sq_size - 1)).
+ */
+ uint16_t reserved16_1;
+ uint32_t reserved32_2;
+ uint64_t reserved64;
+ uint8_t cqe_type_toggle;
+ /*
+ * Indicate valid completion - written by the chip. Cumulus
+ * toggle this bit each time it finished consuming all PBL
+ * entries
+ */
+ #define HWRM_CQ_INPUT_TOGGLE 0x1UL
+ /* This field defines the type of SQ WQE. */
+ #define HWRM_CQ_INPUT_CQE_TYPE_MASK 0x1eUL
+ #define HWRM_CQ_INPUT_CQE_TYPE_SFT 1
+ /*
+ * Requester completion - This is used for both
+ * RC and UD SQ completions.
+ */
+ #define HWRM_CQ_INPUT_CQE_TYPE_INPUT (0x0UL << 1)
+ #define HWRM_CQ_INPUT_RESERVED3_MASK 0xe0UL
+ #define HWRM_CQ_INPUT_RESERVED3_SFT 5
+ uint8_t status;
+ /* This field indicates the status for the CQE. */
+ /* OK is 0 */
+ #define HWRM_CQ_INPUT_STATUS_OK 0x0UL
+ /* BAD_OUTPUTONSE_ERR is 1 */
+ #define HWRM_CQ_INPUT_STATUS_BAD_OUTPUTONSE_ERR 0x1UL
+ /* LOCAL_LENGTH_ERR is 2 */
+ #define HWRM_CQ_INPUT_STATUS_LOCAL_LENGTH_ERR 0x2UL
+ /* LOCAL_QP_OPERATION_ERR is 3 */
+ #define HWRM_CQ_INPUT_STATUS_LOCAL_QP_OPERATION_ERR 0x3UL
+ /* LOCAL_PROTECTION_ERR is 4 */
+ #define HWRM_CQ_INPUT_STATUS_LOCAL_PROTECTION_ERR 0x4UL
+ /* MEMORY_MGT_OPERATION_ERR is 5 */
+ #define HWRM_CQ_INPUT_STATUS_MEMORY_MGT_OPERATION_ERR 0x5UL
+ /* REMOTE_INVALID_INPUTUEST_ERR is 6 */
+ #define HWRM_CQ_INPUT_STATUS_REMOTE_INVALID_INPUTUEST_ERR 0x6UL
+ /* REMOTE_ACCESS_ERR is 7 */
+ #define HWRM_CQ_INPUT_STATUS_REMOTE_ACCESS_ERR 0x7UL
+ /* REMOTE_OPERATION_ERR is 8 */
+ #define HWRM_CQ_INPUT_STATUS_REMOTE_OPERATION_ERR 0x8UL
+ /* RNR_NAK_RETRY_CNT_ERR is 9 */
+ #define HWRM_CQ_INPUT_STATUS_RNR_NAK_RETRY_CNT_ERR 0x9UL
+ /* TRANSPORT_RETRY_CNT_ERR is 10 */
+ #define HWRM_CQ_INPUT_STATUS_TRANSPORT_RETRY_CNT_ERR 0xaUL
+ /* WORK_INPUTUEST_FLUSHED_ERR is 11 */
+ #define HWRM_CQ_INPUT_STATUS_WORK_INPUTUEST_FLUSHED_ERR 0xbUL
+ uint16_t reserved16_2;
+ uint32_t reserved32_1;
+} __attribute__((packed));
+
+/* Responder RC CQE (32 bytes) */
+struct cq_res_rc {
+ uint32_t length;
+ /* The length of the message's payload in bytes, stored in the SGEs */
+ uint32_t imm_data_or_inv_r_key;
+ /*
+ * Immediate data in case the imm_flag set, R_Key to be
+ * invalidated in case inv_flag is set.
+ */
+ uint64_t qp_handle;
+ /*
+ * This is an application level ID used to identify the QP and
+ * its SQ and RQ.
+ */
+ uint64_t mr_handle;
+ /*
+ * Opaque value - valid when inv_flag is set. Used by driver to
+ * reference the buffer used to store PBL when the MR was fast
+ * registered. The driver can reclaim this buffer after an MR
+ * was remotely invalidated. The controller take that value from
+ * the MR referenced by R_Key
+ */
+ uint8_t cqe_type_toggle;
+ /*
+ * Indicate valid completion - written by the chip. Cumulus
+ * toggle this bit each time it finished consuming all PBL
+ * entries
+ */
+ #define HWRM_CQ_RES_RC_TOGGLE 0x1UL
+ /* This field defines the type of SQ WQE. */
+ #define HWRM_CQ_RES_RC_CQE_TYPE_MASK 0x1eUL
+ #define HWRM_CQ_RES_RC_CQE_TYPE_SFT 1
+ /*
+ * Responder RC Completion - This is used for
+ * both RQ and SRQ completions for RC service
+ * QPs.
+ */
+ #define HWRM_CQ_RES_RC_CQE_TYPE_RES_RC (0x1UL << 1)
+ #define HWRM_CQ_RES_RC_RESERVED3_MASK 0xe0UL
+ #define HWRM_CQ_RES_RC_RESERVED3_SFT 5
+ uint8_t status;
+ /* This field indicates the status for the CQE. */
+ /* OK is 0 */
+ #define HWRM_CQ_RES_RC_STATUS_OK 0x0UL
+ /* LOCAL_ACCESS_ERROR is 1 */
+ #define HWRM_CQ_RES_RC_STATUS_LOCAL_ACCESS_ERROR 0x1UL
+ /* LOCAL_LENGTH_ERR is 2 */
+ #define HWRM_CQ_RES_RC_STATUS_LOCAL_LENGTH_ERR 0x2UL
+ /* LOCAL_PROTECTION_ERR is 3 */
+ #define HWRM_CQ_RES_RC_STATUS_LOCAL_PROTECTION_ERR 0x3UL
+ /* LOCAL_QP_OPERATION_ERR is 4 */
+ #define HWRM_CQ_RES_RC_STATUS_LOCAL_QP_OPERATION_ERR 0x4UL
+ /* MEMORY_MGT_OPERATION_ERR is 5 */
+ #define HWRM_CQ_RES_RC_STATUS_MEMORY_MGT_OPERATION_ERR 0x5UL
+ /* REMOTE_INVALID_INPUTUEST_ERR is 6 */
+ #define HWRM_CQ_RES_RC_STATUS_REMOTE_INVALID_INPUTUEST_ERR 0x6UL
+ /* WORK_INPUTUEST_FLUSHED_ERR is 7 */
+ #define HWRM_CQ_RES_RC_STATUS_WORK_INPUTUEST_FLUSHED_ERR 0x7UL
+ /* HW_FLUSH_ERR is 8 */
+ #define HWRM_CQ_RES_RC_STATUS_HW_FLUSH_ERR 0x8UL
+ uint16_t flags;
+ /*
+ * This flag indicates that the completion is for a SRQ entry
+ * rather than for an RQ entry.
+ */
+ #define HWRM_CQ_RES_RC_FLAGS_SRQ 0x1UL
+ /* CQE relates to RQ WQE. */
+ #define HWRM_CQ_RES_RC_FLAGS_SRQ_RQ (0x0UL << 0)
+ /* CQE relates to SRQ WQE. */
+ #define HWRM_CQ_RES_RC_FLAGS_SRQ_SRQ (0x1UL << 0)
+ #define HWRM_CQ_RES_RC_FLAGS_SRQ_LAST \
+ CQ_RES_RC_FLAGS_SRQ_SRQ
+ /* Immediate data indicator */
+ #define HWRM_CQ_RES_RC_FLAGS_IMM 0x2UL
+ /* R_Key invalidate indicator */
+ #define HWRM_CQ_RES_RC_FLAGS_INV 0x4UL
+ #define HWRM_CQ_RES_RC_FLAGS_RDMA 0x8UL
+ /* CQE relates to an incoming Send request */
+ #define HWRM_CQ_RES_RC_FLAGS_RDMA_SEND (0x0UL << 3)
+ /* CQE relates to incoming RDMA Write request */
+ #define HWRM_CQ_RES_RC_FLAGS_RDMA_RDMA_WRITE (0x1UL << 3)
+ #define HWRM_CQ_RES_RC_FLAGS_RDMA_LAST \
+ CQ_RES_RC_FLAGS_RDMA_RDMA_WRITE
+ uint32_t srq_or_rq_wr_id;
+ /*
+ * Opaque value from RQ or SRQ WQE. Used by driver/lib to
+ * reference the WQE in order to claim the received data and
+ * reuse the WQE space
+ */
+ #define HWRM_CQ_RES_RC_SRQ_OR_RQ_WR_ID_MASK 0xfffffUL
+ #define HWRM_CQ_RES_RC_SRQ_OR_RQ_WR_ID_SFT 0
+ #define HWRM_CQ_RES_RC_RESERVED12_MASK 0xfff00000UL
+ #define HWRM_CQ_RES_RC_RESERVED12_SFT 20
+} __attribute__((packed));
+
+/* Responder UD CQE (32 bytes) */
+struct cq_res_ud {
+ uint32_t length;
+ /* The length of the message's payload in bytes, stored in the SGEs */
+ #define HWRM_CQ_RES_UD_LENGTH_MASK 0x3fffUL
+ #define HWRM_CQ_RES_UD_LENGTH_SFT 0
+ #define HWRM_CQ_RES_UD_RESERVED18_MASK 0xffffc000UL
+ #define HWRM_CQ_RES_UD_RESERVED18_SFT 14
+ uint32_t imm_data;
+ /* Immediate data in case the imm_flag set. */
+ uint64_t qp_handle;
+ /*
+ * This is an application level ID used to identify the QP and
+ * its SQ and RQ.
+ */
+ uint16_t src_mac[3];
+ /*
+ * Source MAC address for the UD message placed in the WQE that
+ * is completed by this CQE.
+ */
+ uint16_t src_qp_low;
+ /* Lower 16b of the Source QP value from the DETH header. */
+ uint8_t cqe_type_toggle;
+ /*
+ * Indicate valid completion - written by the chip. Cumulus
+ * toggle this bit each time it finished consuming all PBL
+ * entries
+ */
+ #define HWRM_CQ_RES_UD_TOGGLE 0x1UL
+ /* This field defines the type of SQ WQE. */
+ #define HWRM_CQ_RES_UD_CQE_TYPE_MASK 0x1eUL
+ #define HWRM_CQ_RES_UD_CQE_TYPE_SFT 1
+ /*
+ * Responder UD Completion - This is used for
+ * both RQ and SRQ completion for UD service
+ * QPs.
+ */
+ #define HWRM_CQ_RES_UD_CQE_TYPE_RES_UD (0x2UL << 1)
+ #define HWRM_CQ_RES_UD_RESERVED3_MASK 0xe0UL
+ #define HWRM_CQ_RES_UD_RESERVED3_SFT 5
+ uint8_t status;
+ /* This field indicates the status for the CQE. */
+ /*
+ * This indicates that the completion is without
+ * error. All fields are valid.
+ */
+ #define HWRM_CQ_RES_UD_STATUS_OK 0x0UL
+ /*
+ * This indicates that write access was not
+ * allowed for at least one of the SGEs in the
+ * WQE. This is a fatal error. Only the
+ * srq_or_rq_wr_id is field is valid.
+ */
+ #define HWRM_CQ_RES_UD_STATUS_LOCAL_ACCESS_ERROR 0x1UL
+ /*
+ * This indicates that the packet was too long
+ * for the WQE provided on the SRQ/RQ. This is
+ * not a fatal error. All the fields are valid.
+ */
+ #define HWRM_CQ_RES_UD_STATUS_HW_LOCAL_LENGTH_ERR 0x2UL
+ /* LOCAL_PROTECTION_ERR is 3 */
+ #define HWRM_CQ_RES_UD_STATUS_LOCAL_PROTECTION_ERR 0x3UL
+ /* LOCAL_QP_OPERATION_ERR is 4 */
+ #define HWRM_CQ_RES_UD_STATUS_LOCAL_QP_OPERATION_ERR 0x4UL
+ /* MEMORY_MGT_OPERATION_ERR is 5 */
+ #define HWRM_CQ_RES_UD_STATUS_MEMORY_MGT_OPERATION_ERR 0x5UL
+ /* WORK_INPUTUEST_FLUSHED_ERR is 7 */
+ #define HWRM_CQ_RES_UD_STATUS_WORK_INPUTUEST_FLUSHED_ERR 0x7UL
+ /* HW_FLUSH_ERR is 8 */
+ #define HWRM_CQ_RES_UD_STATUS_HW_FLUSH_ERR 0x8UL
+ uint16_t flags;
+ /*
+ * This flag indicates that the completion is for a SRQ entry
+ * rather than for an RQ entry.
+ */
+ #define HWRM_CQ_RES_UD_FLAGS_SRQ 0x1UL
+ /* CQE relates to RQ WQE. */
+ #define HWRM_CQ_RES_UD_FLAGS_SRQ_RQ (0x0UL << 0)
+ /* CQE relates to SRQ WQE. */
+ #define HWRM_CQ_RES_UD_FLAGS_SRQ_SRQ (0x1UL << 0)
+ #define HWRM_CQ_RES_UD_FLAGS_SRQ_LAST \
+ CQ_RES_UD_FLAGS_SRQ_SRQ
+ /* Immediate data indicator */
+ #define HWRM_CQ_RES_UD_FLAGS_IMM 0x2UL
+ #define HWRM_CQ_RES_UD_FLAGS_ROCE_IP_VER_MASK 0xcUL
+ #define HWRM_CQ_RES_UD_FLAGS_ROCE_IP_VER_SFT 2
+ /* RoCEv1 Message */
+ #define HWRM_CQ_RES_UD_FLAGS_ROCE_IP_VER_V1 (0x0UL << 2)
+ /* RoCEv2 IPv4 Message */
+ #define HWRM_CQ_RES_UD_FLAGS_ROCE_IP_VER_V2IPV4 (0x2UL << 2)
+ /* RoCEv2 IPv6 Message */
+ #define HWRM_CQ_RES_UD_FLAGS_ROCE_IP_VER_V2IPV6 (0x3UL << 2)
+ #define HWRM_CQ_RES_UD_FLAGS_ROCE_IP_VER_LAST \
+ CQ_RES_UD_FLAGS_ROCE_IP_VER_V2IPV6
+ uint32_t src_qp_high_srq_or_rq_wr_id;
+ /* Upper 8b of the Source QP value from the DETH header. */
+ /*
+ * Opaque value from RQ or SRQ WQE. Used by driver/lib to
+ * reference the WQE in order to claim the received data and
+ * reuse the WQE space
+ */
+ #define HWRM_CQ_RES_UD_SRQ_OR_RQ_WR_ID_MASK 0xfffffUL
+ #define HWRM_CQ_RES_UD_SRQ_OR_RQ_WR_ID_SFT 0
+ #define HWRM_CQ_RES_UD_RESERVED4_MASK 0xf00000UL
+ #define HWRM_CQ_RES_UD_RESERVED4_SFT 20
+ /* Upper 8b of the Source QP value from the DETH header. */
+ #define HWRM_CQ_RES_UD_SRC_QP_HIGH_MASK 0xff000000UL
+ #define HWRM_CQ_RES_UD_SRC_QP_HIGH_SFT 24
+} __attribute__((packed));
+
+/* Responder RawEth and QP1 CQE (32 bytes) */
+struct cq_res_raweth_qp1 {
+ uint16_t length;
+ /* The length of the message's payload in bytes, stored in the SGEs */
+ #define HWRM_CQ_RES_RAWETH_QP1_LENGTH_MASK 0x3fffUL
+ #define HWRM_CQ_RES_RAWETH_QP1_LENGTH_SFT 0
+ #define HWRM_CQ_RES_RAWETH_QP1_RESERVED2_MASK 0xc000UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RESERVED2_SFT 14
+ uint16_t raweth_qp1_flags;
+ /*
+ * When this bit is '1', it indicates a packet that has an error
+ * of some type. Type of error is indicated in
+ * raweth_qp1_errors.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ERROR 0x1UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_RESERVED5_1_MASK 0x3eUL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_RESERVED5_1_SFT 1
+ /*
+ * This value indicates what the inner packet determined for the
+ * packet was.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_MASK 0x3c0UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_SFT 6
+ /* Not Known: Indicates that the packet type was not known. */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_NOT_KNOWN \
+ (0x0UL << 6)
+ /*
+ * IP Packet: Indicates that the packet was an
+ * IP packet, but further classification was not
+ * possible.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_IP (0x1UL << 6)
+ /*
+ * TCP Packet: Indicates that the packet was IP
+ * and TCP. This indicates that the
+ * raweth_qp1_payload_offset field is valid.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_TCP (0x2UL << 6)
+ /*
+ * UDP Packet: Indicates that the packet was IP
+ * and UDP. This indicates that the
+ * raweth_qp1_payload_offset field is valid.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_UDP (0x3UL << 6)
+ /*
+ * FCoE Packet: Indicates that the packet was
+ * recognized as a FCoE. This also indicates
+ * that the raweth_qp1_payload_offset field is
+ * valid.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_FCOE (0x4UL << 6)
+ /*
+ * RoCE Packet: Indicates that the packet was
+ * recognized as a RoCE. This also indicates
+ * that the raweth_qp1_payload_offset field is
+ * valid.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_ROCE (0x5UL << 6)
+ /*
+ * ICMP Packet: Indicates that the packet was
+ * recognized as ICMP. This indicates that the
+ * raweth_qp1_payload_offset field is valid.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_ICMP (0x7UL << 6)
+ /*
+ * PtP packet wo/timestamp: Indicates that the
+ * packet was recognized as a PtP packet.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_PTP_WO_TIMESTAMP \
+ (0x8UL << 6)
+ /*
+ * PtP packet w/timestamp: Indicates that the
+ * packet was recognized as a PtP packet and
+ * that a timestamp was taken for the packet.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_PTP_W_TIMESTAMP \
+ (0x9UL << 6)
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_LAST \
+ CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_ITYPE_PTP_W_TIMESTAMP
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_MASK 0x3ffUL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS_SFT 0
+ #define HWRM_CQ_RES_RAWETH_QP1_RESERVED6_MASK 0xfc00UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RESERVED6_SFT 10
+ uint16_t raweth_qp1_errors;
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_RESERVED4_MASK 0xfUL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_RESERVED4_SFT 0
+ /* This indicates that there was an error in the IP header checksum. */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_IP_CS_ERROR 0x10UL
+ /*
+ * This indicates that there was an error in the TCP, UDP or
+ * ICMP checksum.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_L4_CS_ERROR 0x20UL
+ /*
+ * This indicates that there was an error in the tunnel IP
+ * header checksum.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_IP_CS_ERROR 0x40UL
+ /*
+ * This indicates that there was an error in the tunnel UDP
+ * checksum.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_L4_CS_ERROR 0x80UL
+ /*
+ * This indicates that there was a CRC error on either an FCoE
+ * or RoCE packet. The itype indicates the packet type.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_CRC_ERROR 0x100UL
+ /*
+ * This indicates that there was an error in the tunnel portion
+ * of the packet when this field is non-zero.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_MASK \
+ 0xe00UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_SFT 9
+ /*
+ * No additional error occurred on the tunnel
+ * portion of the packet of the packet does not
+ * have a tunnel.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_NO_ERROR \
+ (0x0UL << 9)
+ /*
+ * Indicates that IP header version does not
+ * match expectation from L2 Ethertype for IPv4
+ * and IPv6 in the tunnel header.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_T_L3_BAD_VERSION \
+ (0x1UL << 9)
+ /*
+ * Indicates that header length is out of range
+ * in the tunnel header. Valid for IPv4.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_T_L3_BAD_HDR_LEN \
+ (0x2UL << 9)
+ /*
+ * Indicates that the physical packet is shorter
+ * than that claimed by the PPPoE header length
+ * for a tunnel PPPoE packet.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_TUNNEL_TOTAL_ERROR \
+ (0x3UL << 9)
+ /*
+ * Indicates that physical packet is shorter
+ * than that claimed by the tunnel l3 header
+ * length. Valid for IPv4, or IPv6 tunnel packet
+ * packets.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_T_IP_TOTAL_ERROR \
+ (0x4UL << 9)
+ /*
+ * Indicates that the physical packet is shorter
+ * than that claimed by the tunnel UDP header
+ * length for a tunnel UDP packet that is not
+ * fragmented.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_T_UDP_TOTAL_ERROR \
+ (0x5UL << 9)
+ /*
+ * indicates that the IPv4 TTL or IPv6 hop limit
+ * check have failed (e.g. TTL = 0) in the
+ * tunnel header. Valid for IPv4, and IPv6.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL \
+ (0x6UL << 9)
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_LAST \
+ CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL
+ /*
+ * This indicates that there was an error in the inner portion
+ * of the packet when this field is non-zero.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_MASK 0xf000UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_SFT 12
+ /*
+ * No additional error occurred on the tunnel
+ * portion of the packet of the packet does not
+ * have a tunnel.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_NO_ERROR \
+ (0x0UL << 12)
+ /*
+ * Indicates that IP header version does not
+ * match expectation from L2 Ethertype for IPv4
+ * and IPv6 or that option other than VFT was
+ * parsed on FCoE packet.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_L3_BAD_VERSION \
+ (0x1UL << 12)
+ /*
+ * indicates that header length is out of range.
+ * Valid for IPv4 and RoCE
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_L3_BAD_HDR_LEN \
+ (0x2UL << 12)
+ /*
+ * indicates that the IPv4 TTL or IPv6 hop limit
+ * check have failed (e.g. TTL = 0). Valid for
+ * IPv4, and IPv6
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_L3_BAD_TTL \
+ (0x3UL << 12)
+ /*
+ * Indicates that physical packet is shorter
+ * than that claimed by the l3 header length.
+ * Valid for IPv4, IPv6 packet or RoCE packets.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_IP_TOTAL_ERROR \
+ (0x4UL << 12)
+ /*
+ * Indicates that the physical packet is shorter
+ * than that claimed by the UDP header length
+ * for a UDP packet that is not fragmented.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_UDP_TOTAL_ERROR \
+ (0x5UL << 12)
+ /*
+ * Indicates that TCP header length > IP
+ * payload. Valid for TCP packets only.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN \
+ (0x6UL << 12)
+ /* Indicates that TCP header length < 5. Valid for TCP. */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN_TOO_SMALL \
+ (0x7UL << 12)
+ /*
+ * Indicates that TCP option headers result in a
+ * TCP header size that does not match data
+ * offset in TCP header. Valid for TCP.
+ */
+ #define \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN \
+ (0x8UL << 12)
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_LAST \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN
+ uint16_t raweth_qp1_cfa_code;
+ /*
+ * This field identifies the CFA action rule that was used for
+ * this packet.
+ */
+ uint64_t qp_handle;
+ /*
+ * This is an application level ID used to identify the QP and
+ * its SQ and RQ.
+ */
+ uint32_t raweth_qp1_flags2;
+ /*
+ * This indicates that the ip checksum was calculated for the
+ * inner packet and that the ip_cs_error field indicates if
+ * there was an error.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_IP_CS_CALC 0x1UL
+ /*
+ * This indicates that the TCP, UDP or ICMP checksum was
+ * calculated for the inner packet and that the l4_cs_error
+ * field indicates if there was an error.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_L4_CS_CALC 0x2UL
+ /*
+ * This indicates that the ip checksum was calculated for the
+ * tunnel header and that the t_ip_cs_error field indicates if
+ * there was an error.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_T_IP_CS_CALC 0x4UL
+ /*
+ * This indicates that the UDP checksum was calculated for the
+ * tunnel packet and that the t_l4_cs_error field indicates if
+ * there was an error.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_T_L4_CS_CALC 0x8UL
+ /*
+ * This value indicates what format the raweth_qp1_metadata
+ * field is.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_META_FORMAT_MASK 0xf0UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_META_FORMAT_SFT 4
+ /* No metadata information. Value is zero. */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_META_FORMAT_NONE \
+ (0x0UL << 4)
+ /*
+ * The raweth_qp1_metadata field contains the
+ * VLAN tag and TPID value. -
+ * raweth_qp1_metadata[11:0] contains the vlan
+ * VID value. - raweth_qp1_metadata[12] contains
+ * the vlan DE value. -
+ * raweth_qp1_metadata[15:13] contains the vlan
+ * PRI value. - raweth_qp1_metadata[31:16]
+ * contains the vlan TPID value.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_META_FORMAT_VLAN \
+ (0x1UL << 4)
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_META_FORMAT_LAST \
+ HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_META_FORMAT_VLAN
+ /*
+ * This field indicates the IP type for the inner-most IP
+ * header. A value of '0' indicates IPv4. A value of '1'
+ * indicates IPv6. This value is only valid if itype indicates a
+ * packet with an IP header.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_FLAGS2_IP_TYPE 0x100UL
+ uint32_t raweth_qp1_metadata;
+ /*
+ * This is data from the CFA block as indicated by the
+ * meta_format field.
+ */
+ /* When meta_format=1, this value is the VLAN VID. */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_METADATA_VID_MASK 0xfffUL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_METADATA_VID_SFT 0
+ /* When meta_format=1, this value is the VLAN DE. */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_METADATA_DE 0x1000UL
+ /* When meta_format=1, this value is the VLAN PRI. */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_METADATA_PRI_MASK 0xe000UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_METADATA_PRI_SFT 13
+ /* When meta_format=1, this value is the VLAN TPID. */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_METADATA_TPID_MASK \
+ 0xffff0000UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_METADATA_TPID_SFT 16
+ uint8_t cqe_type_toggle;
+ /*
+ * Indicate valid completion - written by the chip. Cumulus
+ * toggle this bit each time it finished consuming all PBL
+ * entries
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_TOGGLE 0x1UL
+ /* This field defines the type of SQ WQE. */
+ #define HWRM_CQ_RES_RAWETH_QP1_CQE_TYPE_MASK 0x1eUL
+ #define HWRM_CQ_RES_RAWETH_QP1_CQE_TYPE_SFT 1
+ /*
+ * Responder RawEth and QP1 Completion - This is
+ * used for RQ completion for RawEth service and
+ * QP1 service QPs.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_CQE_TYPE_RES_RAWETH_QP1 (0x3UL << 1)
+ #define HWRM_CQ_RES_RAWETH_QP1_RESERVED3_MASK 0xe0UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RESERVED3_SFT 5
+ uint8_t status;
+ /* This field indicates the status for the CQE. */
+ /*
+ * This indicates that the completion is without
+ * error. All fields are valid.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_STATUS_OK 0x0UL
+ /*
+ * This indicates that write access was not
+ * allowed for at least one of the SGEs in the
+ * WQE. This is a fatal error. Only the
+ * srq_or_rq_wr_id is field is valid.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_STATUS_LOCAL_ACCESS_ERROR 0x1UL
+ /*
+ * This indicates that the packet was too long
+ * for the WQE provided on the RQ. This is not a
+ * fatal error. All the fields are valid.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_STATUS_HW_LOCAL_LENGTH_ERR 0x2UL
+ /* LOCAL_PROTECTION_ERR is 3 */
+ #define HWRM_CQ_RES_RAWETH_QP1_STATUS_LOCAL_PROTECTION_ERR 0x3UL
+ /* LOCAL_QP_OPERATION_ERR is 4 */
+ #define HWRM_CQ_RES_RAWETH_QP1_STATUS_LOCAL_QP_OPERATION_ERR 0x4UL
+ /* MEMORY_MGT_OPERATION_ERR is 5 */
+ #define HWRM_CQ_RES_RAWETH_QP1_STATUS_MEMORY_MGT_OPERATION_ERR 0x5UL
+ /* WORK_INPUTUEST_FLUSHED_ERR is 7 */
+ #define HWRM_CQ_RES_RAWETH_QP1_STATUS_WORK_INPUTUEST_FLUSHED_ERR 0x7UL
+ /* HW_FLUSH_ERR is 8 */
+ #define HWRM_CQ_RES_RAWETH_QP1_STATUS_HW_FLUSH_ERR 0x8UL
+ uint16_t flags;
+ /*
+ * This flag indicates that the completion is for a SRQ entry
+ * rather than for an RQ entry.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_FLAGS_SRQ 0x1UL
+ /* CQE relates to RQ WQE. */
+ #define HWRM_CQ_RES_RAWETH_QP1_FLAGS_SRQ_RQ 0x0UL
+ /* CQE relates to SRQ WQE. */
+ #define HWRM_CQ_RES_RAWETH_QP1_FLAGS_SRQ_SRQ 0x1UL
+ #define HWRM_CQ_RES_RAWETH_QP1_FLAGS_SRQ_LAST \
+ CQ_RES_RAWETH_QP1_FLAGS_SRQ_SRQ
+ uint32_t raweth_qp1_payload_offset_srq_or_rq_wr_id;
+ /*
+ * This value indicates the offset in bytes from the beginning
+ * of the packet where the inner payload starts. This value is
+ * valid for TCP, UDP, FCoE, and RoCE packets. A value of zero
+ * indicates an offset of 256 bytes.
+ */
+ /*
+ * Opaque value from RQ or SRQ WQE. Used by driver/lib to
+ * reference the WQE in order to claim the received data and
+ * reuse the WQE space
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_SRQ_OR_RQ_WR_ID_MASK 0xfffffUL
+ #define HWRM_CQ_RES_RAWETH_QP1_SRQ_OR_RQ_WR_ID_SFT 0
+ #define HWRM_CQ_RES_RAWETH_QP1_RESERVED4_MASK 0xf00000UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RESERVED4_SFT 20
+ /*
+ * This value indicates the offset in bytes from the beginning
+ * of the packet where the inner payload starts. This value is
+ * valid for TCP, UDP, FCoE, and RoCE packets. A value of zero
+ * indicates an offset of 256 bytes.
+ */
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_PAYLOAD_OFFSET_MASK \
+ 0xff000000UL
+ #define HWRM_CQ_RES_RAWETH_QP1_RAWETH_QP1_PAYLOAD_OFFSET_SFT 24
+} __attribute__((packed));
+
+/* Terminal CQE (32 bytes) */
+struct cq_terminal {
+ uint64_t qp_handle;
+ /*
+ * This is an application level ID used to identify the QP and
+ * its SQ and RQ.
+ */
+ uint16_t sq_cons_idx;
+ /*
+ * Final SQ Consumer Index value. Any additional SQ WQEs will
+ * have to be completed by the user provider.
+ */
+ uint16_t rq_cons_idx;
+ /*
+ * Final RQ Consumer Index value. Any additional RQ WQEs will
+ * have to be completed by the user provider.
+ */
+ uint32_t reserved32_1;
+ uint64_t reserved64_3;
+ uint8_t cqe_type_toggle;
+ /*
+ * Indicate valid completion - written by the chip. Cumulus
+ * toggle this bit each time it finished consuming all PBL
+ * entries
+ */
+ #define HWRM_CQ_TERMINAL_TOGGLE 0x1UL
+ /* This field defines the type of SQ WQE. */
+ #define HWRM_CQ_TERMINAL_CQE_TYPE_MASK 0x1eUL
+ #define HWRM_CQ_TERMINAL_CQE_TYPE_SFT 1
+ /*
+ * Terminal completion - This is used to
+ * indicate that no further completions will be
+ * made for this QP on this CQ.
+ */
+ #define HWRM_CQ_TERMINAL_CQE_TYPE_TERMINAL (0xeUL << 1)
+ #define HWRM_CQ_TERMINAL_RESERVED3_MASK 0xe0UL
+ #define HWRM_CQ_TERMINAL_RESERVED3_SFT 5
+ uint8_t status;
+ /* This field indicates the status for the CQE. */
+ /* OK is 0 */
+ #define HWRM_CQ_TERMINAL_STATUS_OK 0x0UL
+ uint16_t reserved16;
+ uint32_t reserved32_2;
+} __attribute__((packed));
+
+/* Cutoff CQE (32 bytes) */
+struct cq_cutoff {
+ uint64_t reserved64_1;
+ uint64_t reserved64_2;
+ uint64_t reserved64_3;
+ uint8_t cqe_type_toggle;
+ /*
+ * Indicate valid completion - written by the chip. Cumulus
+ * toggle this bit each time it finished consuming all PBL
+ * entries
+ */
+ #define HWRM_CQ_CUTOFF_TOGGLE 0x1UL
+ /* This field defines the type of SQ WQE. */
+ #define HWRM_CQ_CUTOFF_CQE_TYPE_MASK 0x1eUL
+ #define HWRM_CQ_CUTOFF_CQE_TYPE_SFT 1
+ /* Cut off CQE; for CQ resize see CQ and SRQ Resize */
+ #define HWRM_CQ_CUTOFF_CQE_TYPE_CUT_OFF (0xfUL << 1)
+ #define HWRM_CQ_CUTOFF_RESERVED3_MASK 0xe0UL
+ #define HWRM_CQ_CUTOFF_RESERVED3_SFT 5
+ uint8_t status;
+ /* This field indicates the status for the CQE. */
+ /* OK is 0 */
+ #define HWRM_CQ_CUTOFF_STATUS_OK 0x0UL
+ uint16_t reserved16;
+ uint32_t reserved32;
+} __attribute__((packed));
+
+/* Notification Queue (NQ) Structures */
+/*
+ * Description: This completion indicates that the DBQ has reached the
+ * programmed threshold value.
+ */
+/* Base NQ Record (16 bytes) */
+struct nq_base {
+ uint16_t info10_type;
+ /* info10 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_NQ_BASE_TYPE_MASK 0x3fUL
+ #define HWRM_NQ_BASE_TYPE_SFT 0
+ /* CQ Notification */
+ #define HWRM_NQ_BASE_TYPE_CQ_NOTIFICATION 0x30UL
+ /* SRQ Threshold Event */
+ #define HWRM_NQ_BASE_TYPE_SRQ_EVENT 0x32UL
+ /* DBQ Threshold Event */
+ #define HWRM_NQ_BASE_TYPE_DBQ_EVENT 0x34UL
+ /* QP Async Notification */
+ #define HWRM_NQ_BASE_TYPE_QP_EVENT 0x38UL
+ /* Function Async Notification */
+ #define HWRM_NQ_BASE_TYPE_FUNC_EVENT 0x3aUL
+ /* info10 is 10 b */
+ #define HWRM_NQ_BASE_INFO10_MASK 0xffc0UL
+ #define HWRM_NQ_BASE_INFO10_SFT 6
+ uint16_t info16;
+ /* info16 is 16 b */
+ uint32_t info32;
+ /* info32 is 32 b */
+ uint32_t info63_v[2];
+ /* info63 is 63 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_NQ_BASE_V 0x1UL
+ /* info63 is 63 b */
+ #define HWRM_NQ_BASE_INFO63_MASK 0xfffffffeUL
+ #define HWRM_NQ_BASE_INFO63_SFT 1
+} __attribute__((packed));
+
+/* Completion Queue Notification (16 bytes) */
+struct nq_cn {
+ uint16_t type;
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_NQ_CN_TYPE_MASK 0x3fUL
+ #define HWRM_NQ_CN_TYPE_SFT 0
+ /* CQ Notification */
+ #define HWRM_NQ_CN_TYPE_CQ_NOTIFICATION 0x30UL
+ #define HWRM_NQ_CN_RESERVED9_MASK 0xffc0UL
+ #define HWRM_NQ_CN_RESERVED9_SFT 6
+ uint16_t reserved16;
+ uint32_t cq_handle_low;
+ /*
+ * This is an application level ID used to identify the CQ. This
+ * field carries the lower 32b of the value.
+ */
+ uint32_t v;
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_NQ_CN_V 0x1UL
+ #define HWRM_NQ_CN_RESERVED31_MASK 0xfffffffeUL
+ #define HWRM_NQ_CN_RESERVED31_SFT 1
+ uint32_t cq_handle_high;
+ /*
+ * This is an application level ID used to identify the CQ. This
+ * field carries the upper 32b of the value.
+ */
+} __attribute__((packed));
+
+/* SRQ Event Notification (16 bytes) */
+struct nq_srq_event {
+ uint8_t type;
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_NQ_SRQ_EVENT_TYPE_MASK 0x3fUL
+ #define HWRM_NQ_SRQ_EVENT_TYPE_SFT 0
+ /* SRQ Threshold Event */
+ #define HWRM_NQ_SRQ_EVENT_TYPE_SRQ_EVENT 0x32UL
+ #define HWRM_NQ_SRQ_EVENT_RESERVED1_MASK 0xc0UL
+ #define HWRM_NQ_SRQ_EVENT_RESERVED1_SFT 6
+ uint8_t event;
+ /*
+ * This value define what type of async event has occurred on
+ * the SRQ.
+ */
+ /* The threshold event has occurred on the specified SRQ. */
+ #define HWRM_NQ_SRQ_EVENT_EVENT_SRQ_THRESHOLD_EVENT 0x1UL
+ uint16_t reserved16;
+ uint32_t srq_handle_low;
+ /*
+ * This is the SRQ handle value for the queue that has reached
+ * it's event threshold. This field carries the lower 32b of the
+ * value.
+ */
+ uint32_t v;
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_NQ_SRQ_EVENT_V 0x1UL
+ #define HWRM_NQ_SRQ_EVENT_RESERVED31_MASK 0xfffffffeUL
+ #define HWRM_NQ_SRQ_EVENT_RESERVED31_SFT 1
+ uint32_t srq_handle_high;
+ /*
+ * This is the SRQ handle value for the queue that has reached
+ * it's event threshold. This field carries the upper 32b of the
+ * value.
+ */
+} __attribute__((packed));
+
+/* DBQ Async Event Notification (16 bytes) */
+struct nq_dbq_event {
+ uint8_t type;
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_NQ_DBQ_EVENT_TYPE_MASK 0x3fUL
+ #define HWRM_NQ_DBQ_EVENT_TYPE_SFT 0
+ /* DBQ Threshold Event */
+ #define HWRM_NQ_DBQ_EVENT_TYPE_DBQ_EVENT 0x34UL
+ #define HWRM_NQ_DBQ_EVENT_RESERVED1_MASK 0xc0UL
+ #define HWRM_NQ_DBQ_EVENT_RESERVED1_SFT 6
+ uint8_t event;
+ /* This value define what type of action the driver should take. */
+ /*
+ * The driver should start writing dummy values
+ * to the the doorbell in an attempt to consume
+ * all the PCIE posted write resources and
+ * prevent doorbell overflow.
+ */
+ #define HWRM_NQ_DBQ_EVENT_EVENT_DBQ_THRESHOLD_EVENT 0x1UL
+ uint16_t db_pfid;
+ /*
+ * This is the PFID of function that wrote the doorbell that
+ * crossed the async event threshold.
+ */
+ #define HWRM_NQ_DBQ_EVENT_DB_PFID_MASK 0xfUL
+ #define HWRM_NQ_DBQ_EVENT_DB_PFID_SFT 0
+ #define HWRM_NQ_DBQ_EVENT_RESERVED12_MASK 0xfff0UL
+ #define HWRM_NQ_DBQ_EVENT_RESERVED12_SFT 4
+ uint32_t db_dpi;
+ /*
+ * This is the DPI of the doorbell write that crossed the async
+ * event threshold.
+ */
+ #define HWRM_NQ_DBQ_EVENT_DB_DPI_MASK 0xfffffUL
+ #define HWRM_NQ_DBQ_EVENT_DB_DPI_SFT 0
+ #define HWRM_NQ_DBQ_EVENT_RESERVED12_2_MASK 0xfff00000UL
+ #define HWRM_NQ_DBQ_EVENT_RESERVED12_2_SFT 20
+ uint32_t v;
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_NQ_DBQ_EVENT_V 0x1UL
+ #define HWRM_NQ_DBQ_EVENT_RESERVED32_MASK 0xfffffffeUL
+ #define HWRM_NQ_DBQ_EVENT_RESERVED32_SFT 1
+ uint32_t db_type_db_xid;
+ /*
+ * DB 'type' field from doorbell that crossed the async event
+ * threshold.
+ */
+ /*
+ * DB 'XID' field from doorbell that crossed the async event
+ * threshold. This is a QPID, SID, or CID, depending on the
+ * db_type field.
+ */
+ #define HWRM_NQ_DBQ_EVENT_DB_XID_MASK 0xfffffUL
+ #define HWRM_NQ_DBQ_EVENT_DB_XID_SFT 0
+ #define HWRM_NQ_DBQ_EVENT_RESERVED8_MASK 0xff00000UL
+ #define HWRM_NQ_DBQ_EVENT_RESERVED8_SFT 20
+ /*
+ * DB 'type' field from doorbell that crossed the async event
+ * threshold.
+ */
+ #define HWRM_NQ_DBQ_EVENT_DB_TYPE_MASK 0xf0000000UL
+ #define HWRM_NQ_DBQ_EVENT_DB_TYPE_SFT 28
+} __attribute__((packed));
+
+/* Read Request/Response Queue Structures */
+/*
+ * Description: This queue messages is used on the ORRQ to indicate output read
+ * requests to the RX side of the chip.
+ */
+/* Input Read Request Queue (IRRQ) Message (32 bytes) */
+struct xrrq_irrq {
+ uint16_t credits_type;
+ /*
+ * The credit code calculated by Rx path when receiving the
+ * request. It will be placed in the syndrome credit code with
+ * the acks on first and last response.
+ */
+ /* Type indication */
+ #define HWRM_XRRQ_IRRQ_TYPE 0x1UL
+ /* RDMA Read */
+ #define HWRM_XRRQ_IRRQ_TYPE_READ_INPUT 0x0UL
+ /* Atomic */
+ #define HWRM_XRRQ_IRRQ_TYPE_ATOMIC_INPUT 0x1UL
+ #define HWRM_XRRQ_IRRQ_RESERVED10_MASK 0x7feUL
+ #define HWRM_XRRQ_IRRQ_RESERVED10_SFT 1
+ /*
+ * The credit code calculated by Rx path when receiving the
+ * request. It will be placed in the syndrome credit code with
+ * the acks on first and last response.
+ */
+ #define HWRM_XRRQ_IRRQ_CREDITS_MASK 0xf800UL
+ #define HWRM_XRRQ_IRRQ_CREDITS_SFT 11
+ uint16_t reserved16;
+ uint32_t reserved32;
+ uint32_t psn;
+ /* The PSN of the outstanding incoming request */
+ #define HWRM_XRRQ_IRRQ_PSN_MASK 0xffffffUL
+ #define HWRM_XRRQ_IRRQ_PSN_SFT 0
+ #define HWRM_XRRQ_IRRQ_RESERVED8_1_MASK 0xff000000UL
+ #define HWRM_XRRQ_IRRQ_RESERVED8_1_SFT 24
+ uint32_t msn;
+ /*
+ * The value of QPC.pending_ack_msn after it is incremented as a
+ * result of receiving the read/atomic request. IRRQ.msn-1 will
+ * be placed in the MSN field of the first response and IRRQ.msn
+ * will placed in the MSN field of the last or only response.
+ */
+ #define HWRM_XRRQ_IRRQ_MSN_MASK 0xffffffUL
+ #define HWRM_XRRQ_IRRQ_MSN_SFT 0
+ #define HWRM_XRRQ_IRRQ_RESERVED8_2_MASK 0xff000000UL
+ #define HWRM_XRRQ_IRRQ_RESERVED8_2_SFT 24
+ uint64_t va_or_atomic_result;
+ /*
+ * Virtual address on local host for RDMA READ In case of
+ * duplicate Atomic, the VA is not required to be validated,
+ * only the PSN is, thus this field is used to store the value
+ * returned in the Ack to the atomic request, and if duplicate
+ * arrives, this value is used again for resending the ack.
+ */
+ uint32_t rdma_r_key;
+ /* The key to the MR/W in the request */
+ uint32_t length;
+ /*
+ * Length in bytes of the data requested. Length must be 8 if
+ * type is atomic.
+ */
+} __attribute__((packed));
+
+/* Output Read Request Queue (ORRQ) Message (32 bytes) */
+struct xrrq_orrq {
+ uint16_t num_sges_type;
+ /*
+ * Up to 6 SGEs. This value is 1 if type is atomic as one SGE is
+ * required to store Atomic response result field. 2 more bits
+ * allocated for future growth. Note that, if num_sges is 1 for
+ * an RDMA Read request, then the first_sge_phy_or_sing_sge_va,
+ * single_sge_l_key, and single_sge_size fields will be
+ * populated from the single SGE. If num_sges is 2 or more for
+ * an RDMA Read request, then the first_sge_phy_or_sing_sge_va
+ * field carries the physical address in host memory where the
+ * first sge is stored. The single_sge_l_key and single_sge_size
+ * fields are unused in this case. A special case is a zero-
+ * length, zero-sge RDMA read request WQE. In this situation,
+ * num_sges will be 1. However, first_sge_phy_or_sing_sge_va,
+ * single_sge_l_key, and single_sge_size will all be populated
+ * with zeros.
+ */
+ /* Type indication */
+ #define HWRM_XRRQ_ORRQ_TYPE 0x1UL
+ /* RDMA Read */
+ #define HWRM_XRRQ_ORRQ_TYPE_READ_INPUT 0x0UL
+ /* Atomic */
+ #define HWRM_XRRQ_ORRQ_TYPE_ATOMIC_INPUT 0x1UL
+ #define HWRM_XRRQ_ORRQ_RESERVED10_MASK 0x7feUL
+ #define HWRM_XRRQ_ORRQ_RESERVED10_SFT 1
+ /*
+ * Up to 6 SGEs. This value is 1 if type is atomic as one SGE is
+ * required to store Atomic response result field. 2 more bits
+ * allocated for future growth. Note that, if num_sges is 1 for
+ * an RDMA Read request, then the first_sge_phy_or_sing_sge_va,
+ * single_sge_l_key, and single_sge_size fields will be
+ * populated from the single SGE. If num_sges is 2 or more for
+ * an RDMA Read request, then the first_sge_phy_or_sing_sge_va
+ * field carries the physical address in host memory where the
+ * first sge is stored. The single_sge_l_key and single_sge_size
+ * fields are unused in this case. A special case is a zero-
+ * length, zero-sge RDMA read request WQE. In this situation,
+ * num_sges will be 1. However, first_sge_phy_or_sing_sge_va,
+ * single_sge_l_key, and single_sge_size will all be populated
+ * with zeros.
+ */
+ #define HWRM_XRRQ_ORRQ_NUM_SGES_MASK 0xf800UL
+ #define HWRM_XRRQ_ORRQ_NUM_SGES_SFT 11
+ uint16_t reserved16;
+ uint32_t length;
+ /*
+ * Length in bytes of the data requested. Length must be 8 if
+ * type is atomic.
+ */
+ uint32_t psn;
+ /* The PSN of the outstanding outgoing request */
+ #define HWRM_XRRQ_ORRQ_PSN_MASK 0xffffffUL
+ #define HWRM_XRRQ_ORRQ_PSN_SFT 0
+ #define HWRM_XRRQ_ORRQ_RESERVED8_1_MASK 0xff000000UL
+ #define HWRM_XRRQ_ORRQ_RESERVED8_1_SFT 24
+ uint32_t end_psn;
+ /*
+ * The expected last PSN on a response to this request where an
+ * ack with response, rather than just response, should arrive.
+ * If ack arrive with smaller PSN than end_psn then it is
+ * considered a NAK.
+ */
+ #define HWRM_XRRQ_ORRQ_END_PSN_MASK 0xffffffUL
+ #define HWRM_XRRQ_ORRQ_END_PSN_SFT 0
+ #define HWRM_XRRQ_ORRQ_RESERVED8_2_MASK 0xff000000UL
+ #define HWRM_XRRQ_ORRQ_RESERVED8_2_SFT 24
+ uint64_t first_sge_phy_or_sing_sge_va;
+ /*
+ * If num_sges == 1 this is the va of that SGE. Otherwise,
+ * physical address to the first SGE specified by the WQE.
+ * Points to the first SGE in the Request's WQE in the SQ. It is
+ * assumed that WQE does not cross page boundaries! Driver is
+ * responsible to enforce that. SGEs are 16B aligned 0b0000 lsb
+ * added to get 64 bit address.
+ */
+ uint32_t single_sge_l_key;
+ /* The L_Key of a single SGE if used */
+ uint32_t single_sge_size;
+ /* The size in bytes of the single SGE if used */
+} __attribute__((packed));
+
+/* Page Buffer List Memory Structures (PBL) */
+/*
+ * Description: Page directory entries point to a page directories made up of
+ * PTE values.
+ */
+/* Page Table Entry (PTE) (8 bytes) */
+struct ptu_pte {
+ uint32_t page_next_to_last_last_valid[2];
+ /*
+ * This is the upper bits of the physical page controlled by
+ * this PTE. If the page is larger than 4KB, then the unused
+ * lower bits of the page address should be zero.
+ */
+ /*
+ * This field indicates if the PTE is valid. A value of '0'
+ * indicates that the page is not valid. A value of '1'
+ * indicates that the page is valid. A reference to an invalid
+ * page will return a PTU error.
+ */
+ #define HWRM_PTU_PTE_VALID 0x1UL
+ /*
+ * This field is used only for "ring" PBLs that are used for SQ,
+ * RQ, SRQ, or CQ structures. For all other PBL structures, this
+ * bit should be zero. When this bit is '1', it indicates that
+ * the page pointed to by this PTE is the last page in the ring.
+ * A prefetch for the ring should use the first PTE in the PBL.
+ */
+ #define HWRM_PTU_PTE_LAST 0x2UL
+ /*
+ * This field is used only for "ring" PBLs that are used for SQ,
+ * RQ, SRQ, or CQ structures. For all other PBL structures, this
+ * bit should be zero. When this bit is '1', it indicates that
+ * this is the next-to-last page of the PBL.
+ */
+ #define HWRM_PTU_PTE_NEXT_TO_LAST 0x4UL
+ /* These bits should be programmed to zero. */
+ /*
+ * This is the upper bits of the physical page controlled by
+ * this PTE. If the page is larger than 4KB, then the unused
+ * lower bits of the page address should be zero.
+ */
+ #define HWRM_PTU_PTE_PAGE_MASK 0xfffff000UL
+ #define HWRM_PTU_PTE_PAGE_SFT 12
+} __attribute__((packed));
+
+/* Page Directory Entry (PDE) (8 bytes) */
+struct ptu_pde {
+ uint32_t page_valid[2];
+ /*
+ * This is the upper bits of the physical page controlled by
+ * this PTE. If the page is larger than 4KB, then the unused
+ * lower bits of the page address should be zero.
+ */
+ /*
+ * This field indicates if the PTE is valid. A value of '0'
+ * indicates that the page is not valid. A value of '1'
+ * indicates that the page is valid. A reference to an invalid
+ * page will return a PTU error.
+ */
+ #define HWRM_PTU_PDE_VALID 0x1UL
+ /* These bits should be programmed to zero. */
+ /*
+ * This is the upper bits of the physical page controlled by
+ * this PTE. If the page is larger than 4KB, then the unused
+ * lower bits of the page address should be zero.
+ */
+ #define HWRM_PTU_PDE_PAGE_MASK 0xfffff000UL
+ #define HWRM_PTU_PDE_PAGE_SFT 12
+} __attribute__((packed));
+
+/* RoCE Fastpath Host Structures */
+/*
+ * Note: This section documents the host structures used between RoCE state
+ * machines and RoCE drivers/libraries.
+ */
+/* hwrm_ver_get */
+/*
+ * Description: This function is called by a driver to determine the HWRM
+ * interface version supported by the HWRM firmware, the version of HWRM
+ * firmware implementation, the name of HWRM firmware, the versions of other
+ * embedded firmwares, and the names of other embedded firmwares, etc. Any
+ * interface or firmware version with major = 0, minor = 0, and update = 0 shall
+ * be considered an invalid version.
+ */
+/* Input (24 bytes) */
+struct hwrm_ver_get_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint8_t hwrm_intf_maj;
+ /*
+ * This field represents the major version of HWRM interface
+ * specification supported by the driver HWRM implementation.
+ * The interface major version is intended to change only when
+ * non backward compatible changes are made to the HWRM
+ * interface specification.
+ */
+ uint8_t hwrm_intf_min;
+ /*
+ * This field represents the minor version of HWRM interface
+ * specification supported by the driver HWRM implementation. A
+ * change in interface minor version is used to reflect
+ * significant backward compatible modification to HWRM
+ * interface specification. This can be due to addition or
+ * removal of functionality. HWRM interface specifications with
+ * the same major version but different minor versions are
+ * compatible.
+ */
+ uint8_t hwrm_intf_upd;
+ /*
+ * This field represents the update version of HWRM interface
+ * specification supported by the driver HWRM implementation.
+ * The interface update version is used to reflect minor changes
+ * or bug fixes to a released HWRM interface specification.
+ */
+ uint8_t unused_0[5];
+} __attribute__((packed));
+
+/* Output (128 bytes) */
+struct hwrm_ver_get_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t hwrm_intf_maj;
+ /*
+ * This field represents the major version of HWRM interface
+ * specification supported by the HWRM implementation. The
+ * interface major version is intended to change only when non
+ * backward compatible changes are made to the HWRM interface
+ * specification. A HWRM implementation that is compliant with
+ * this specification shall provide value of 1 in this field.
+ */
+ uint8_t hwrm_intf_min;
+ /*
+ * This field represents the minor version of HWRM interface
+ * specification supported by the HWRM implementation. A change
+ * in interface minor version is used to reflect significant
+ * backward compatible modification to HWRM interface
+ * specification. This can be due to addition or removal of
+ * functionality. HWRM interface specifications with the same
+ * major version but different minor versions are compatible. A
+ * HWRM implementation that is compliant with this specification
+ * shall provide value of 2 in this field.
+ */
+ uint8_t hwrm_intf_upd;
+ /*
+ * This field represents the update version of HWRM interface
+ * specification supported by the HWRM implementation. The
+ * interface update version is used to reflect minor changes or
+ * bug fixes to a released HWRM interface specification. A HWRM
+ * implementation that is compliant with this specification
+ * shall provide value of 2 in this field.
+ */
+ uint8_t hwrm_intf_rsvd;
+ uint8_t hwrm_fw_maj;
+ /*
+ * This field represents the major version of HWRM firmware. A
+ * change in firmware major version represents a major firmware
+ * release.
+ */
+ uint8_t hwrm_fw_min;
+ /*
+ * This field represents the minor version of HWRM firmware. A
+ * change in firmware minor version represents significant
+ * firmware functionality changes.
+ */
+ uint8_t hwrm_fw_bld;
+ /*
+ * This field represents the build version of HWRM firmware. A
+ * change in firmware build version represents bug fixes to a
+ * released firmware.
+ */
+ uint8_t hwrm_fw_rsvd;
+ /*
+ * This field is a reserved field. This field can be used to
+ * represent firmware branches or customer specific releases
+ * tied to a specific (major,minor,update) version of the HWRM
+ * firmware.
+ */
+ uint8_t mgmt_fw_maj;
+ /*
+ * This field represents the major version of mgmt firmware. A
+ * change in major version represents a major release.
+ */
+ uint8_t mgmt_fw_min;
+ /*
+ * This field represents the minor version of mgmt firmware. A
+ * change in minor version represents significant functionality
+ * changes.
+ */
+ uint8_t mgmt_fw_bld;
+ /*
+ * This field represents the build version of mgmt firmware. A
+ * change in update version represents bug fixes.
+ */
+ uint8_t mgmt_fw_rsvd;
+ /*
+ * This field is a reserved field. This field can be used to
+ * represent firmware branches or customer specific releases
+ * tied to a specific (major,minor,update) version
+ */
+ uint8_t netctrl_fw_maj;
+ /*
+ * This field represents the major version of network control
+ * firmware. A change in major version represents a major
+ * release.
+ */
+ uint8_t netctrl_fw_min;
+ /*
+ * This field represents the minor version of network control
+ * firmware. A change in minor version represents significant
+ * functionality changes.
+ */
+ uint8_t netctrl_fw_bld;
+ /*
+ * This field represents the build version of network control
+ * firmware. A change in update version represents bug fixes.
+ */
+ uint8_t netctrl_fw_rsvd;
+ /*
+ * This field is a reserved field. This field can be used to
+ * represent firmware branches or customer specific releases
+ * tied to a specific (major,minor,update) version
+ */
+ uint32_t dev_caps_cfg;
+ /*
+ * This field is used to indicate device's capabilities and
+ * configurations.
+ */
+ /*
+ * If set to 1, then secure firmware update behavior is
+ * supported. If set to 0, then secure firmware update behavior
+ * is not supported.
+ */
+ #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SECURE_FW_UPD_SUPPORTED 0x1UL
+ /*
+ * If set to 1, then firmware based DCBX agent is supported. If
+ * set to 0, then firmware based DCBX agent capability is not
+ * supported on this device.
+ */
+ #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_FW_DCBX_AGENT_SUPPORTED 0x2UL
+ /*
+ * If set to 1, then HWRM short command format is supported. If
+ * set to 0, then HWRM short command format is not supported.
+ */
+ #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SHORT_CMD_SUPPORTED 0x4UL
+ /*
+ * If set to 1, then HWRM short command format is required. If
+ * set to 0, then HWRM short command format is not required.
+ */
+ #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SHORT_CMD_INPUTUIRED 0x8UL
+ uint8_t roce_fw_maj;
+ /*
+ * This field represents the major version of RoCE firmware. A
+ * change in major version represents a major release.
+ */
+ uint8_t roce_fw_min;
+ /*
+ * This field represents the minor version of RoCE firmware. A
+ * change in minor version represents significant functionality
+ * changes.
+ */
+ uint8_t roce_fw_bld;
+ /*
+ * This field represents the build version of RoCE firmware. A
+ * change in update version represents bug fixes.
+ */
+ uint8_t roce_fw_rsvd;
+ /*
+ * This field is a reserved field. This field can be used to
+ * represent firmware branches or customer specific releases
+ * tied to a specific (major,minor,update) version
+ */
+ char hwrm_fw_name[16];
+ /*
+ * This field represents the name of HWRM FW (ASCII chars with
+ * NULL at the end).
+ */
+ char mgmt_fw_name[16];
+ /*
+ * This field represents the name of mgmt FW (ASCII chars with
+ * NULL at the end).
+ */
+ char netctrl_fw_name[16];
+ /*
+ * This field represents the name of network control firmware
+ * (ASCII chars with NULL at the end).
+ */
+ uint32_t reserved2[4];
+ /*
+ * This field is reserved for future use. The responder should
+ * set it to 0. The requester should ignore this field.
+ */
+ char roce_fw_name[16];
+ /*
+ * This field represents the name of RoCE FW (ASCII chars with
+ * NULL at the end).
+ */
+ uint16_t chip_num;
+ /* This field returns the chip number. */
+ uint8_t chip_rev;
+ /* This field returns the revision of chip. */
+ uint8_t chip_metal;
+ /* This field returns the chip metal number. */
+ uint8_t chip_bond_id;
+ /* This field returns the bond id of the chip. */
+ uint8_t chip_platform_type;
+ /*
+ * This value indicates the type of platform used for chip
+ * implementation.
+ */
+ /* ASIC */
+ #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_ASIC 0x0UL
+ /* FPGA platform of the chip. */
+ #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_FPGA 0x1UL
+ /* Palladium platform of the chip. */
+ #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_PALLADIUM 0x2UL
+ uint16_t max_req_win_len;
+ /*
+ * This field returns the maximum value of request window that
+ * is supported by the HWRM. The request window is mapped into
+ * device address space using MMIO.
+ */
+ uint16_t max_resp_len;
+ /* This field returns the maximum value of response buffer in bytes. */
+ uint16_t def_req_timeout;
+ /*
+ * This field returns the default request timeout value in
+ * milliseconds.
+ */
+ uint8_t init_pending;
+ /*
+ * This field will indicate if any subsystems is not fully
+ * initialized.
+ */
+ /*
+ * If set to 1, device is not ready. If set to 0, device is
+ * ready to accept all HWRM commands.
+ */
+ #define HWRM_VER_GET_OUTPUT_INIT_PENDING_DEV_NOT_RDY 0x1UL
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_reset */
+/*
+ * Description: This command resets a hardware function (PCIe function) and
+ * frees any resources used by the function. This command shall be initiated by
+ * the driver after an FLR has occurred to prepare the function for re-use. This
+ * command may also be initiated by a driver prior to doing it's own
+ * configuration. This command puts the function into the reset state. In the
+ * reset state, global and port related features of the chip are not available.
+ */
+/*
+ * Note: This command will reset a function that has already been disabled or
+ * idled. The command returns all the resources owned by the function so a new
+ * driver may allocate and configure resources normally.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_reset_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id_valid field to be configured. */
+ #define HWRM_FUNC_RESET_INPUT_ENABLES_VF_ID_VALID 0x1UL
+ uint16_t vf_id;
+ /*
+ * The ID of the VF that this PF is trying to reset. Only the
+ * parent PF shall be allowed to reset a child VF. A parent PF
+ * driver shall use this field only when a specific child VF is
+ * requested to be reset.
+ */
+ uint8_t func_reset_level;
+ /* This value indicates the level of a function reset. */
+ /*
+ * Reset the caller function and its children
+ * VFs (if any). If no children functions exist,
+ * then reset the caller function only.
+ */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETALL 0x0UL
+ /* Reset the caller function only */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETME 0x1UL
+ /*
+ * Reset all children VFs of the caller function
+ * driver if the caller is a PF driver. It is an
+ * error to specify this level by a VF driver.
+ * It is an error to specify this level by a PF
+ * driver with no children VFs.
+ */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETCHILDREN 0x2UL
+ /*
+ * Reset a specific VF of the caller function
+ * driver if the caller is the parent PF driver.
+ * It is an error to specify this level by a VF
+ * driver. It is an error to specify this level
+ * by a PF driver that is not the parent of the
+ * VF that is being requested to reset.
+ */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETVF 0x3UL
+ uint8_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_reset_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_getfid */
+/*
+ * Description: This command returns the FID value for the function. If a valid
+ * pci_id is provided, then this function returns fid for that PCI function.
+ * Otherwise, it returns FID of the requesting function. This value is needed to
+ * configure Rings and MSI-X vectors so their DMA operations appear correctly on
+ * the PCI bus. For PF-HWRM commands, there is no need for FID. Similarly there
+ * is no need for FID for VF-HWRM commands. In the PF-VF communication, only PF
+ * needs to know FIDs.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_getfid_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the pci_id field to be configured. */
+ #define HWRM_FUNC_GETFID_INPUT_ENABLES_PCI_ID 0x1UL
+ uint16_t pci_id;
+ /*
+ * This value is the PCI ID of the queried function. If ARI is
+ * enabled, then it is Bus Number (8b):Function Number(8b).
+ * Otherwise, it is Bus Number (8b):Device Number (5b):Function
+ * Number(3b).
+ */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_getfid_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t fid;
+ /*
+ * FID value. This value is used to identify operations on the
+ * PCI bus as belonging to a particular PCI function.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vf_alloc */
+/*
+ * Description: This command is used to allocate requested number of virtual
+ * functions on a physical function. It will return the FID value of the first
+ * virtual function. The FIDs of the remaining virtual functions can be derived
+ * by sequentially incrementing the FID value of the first VF. This command
+ * supports the following models for VF allocation: # Allocation of one or more
+ * VFs from a PF without specifying the first VF ID # Allocation of multiple VFs
+ * from a PF starting with a specific VF # Allocation of a specific VF from a PF
+ * If this command is called on a virtual function or a physical function that
+ * is not enabled for SR-IOV, the HWRM shall return an error. The VF IDs
+ * returned by this function remain valid after the VF is disabled or reset.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_vf_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the first_vf_id field to be configured. */
+ #define HWRM_FUNC_VF_ALLOC_INPUT_ENABLES_FIRST_VF_ID 0x1UL
+ uint16_t first_vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint16_t num_vfs;
+ /* The number of virtual functions requested. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_vf_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t first_vf_id;
+ /* The ID of the first VF allocated. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vf_free */
+/*
+ * Description: This command will free allocated virtual functions on a physical
+ * function. If this command is called on a virtual function or a physical
+ * function that is not enabled for SR-IOV, the HWRM shall return an error.
+ * After the successful completion of this command, the VF IDs of the VFs that
+ * are freed on the PF are invalid.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_vf_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the first_vf_id field to be configured. */
+ #define HWRM_FUNC_VF_FREE_INPUT_ENABLES_FIRST_VF_ID 0x1UL
+ uint16_t first_vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint16_t num_vfs;
+ /*
+ * The number of virtual functions requested. 0xFFFF - Cleanup
+ * all children of this PF.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_vf_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vf_cfg */
+/*
+ * Description: This command allows configuration of a VF by its driver. If this
+ * function is called by a PF driver, then the HWRM shall fail this command. If
+ * guest VLAN and/or MAC address are provided in this command, then the HWRM
+ * shall set up appropriate MAC/VLAN filters for the VF that is being
+ * configured. A VF driver should set VF MTU/MRU using this command prior to
+ * allocating RX VNICs or TX rings for the corresponding VF.
+ */
+/* Input (32 bytes) */
+struct hwrm_func_vf_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the mtu field to be configured. */
+ #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_MTU 0x1UL
+ /* This bit must be '1' for the guest_vlan field to be configured. */
+ #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_GUEST_VLAN 0x2UL
+ /*
+ * This bit must be '1' for the async_event_cr field to be
+ * configured.
+ */
+ #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_ASYNC_EVENT_CR 0x4UL
+ /*
+ * This bit must be '1' for the dflt_mac_addr field to be
+ * configured.
+ */
+ #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_DFLT_MAC_ADDR 0x8UL
+ uint16_t mtu;
+ /*
+ * The maximum transmission unit requested on the function. The
+ * HWRM should make sure that the mtu of the function does not
+ * exceed the mtu of the physical port that this function is
+ * associated with. In addition to requesting mtu per function,
+ * it is possible to configure mtu per transmit ring. By
+ * default, the mtu of each transmit ring associated with a
+ * function is equal to the mtu of the function. The HWRM should
+ * make sure that the mtu of each transmit ring that is assigned
+ * to a function has a valid mtu.
+ */
+ uint16_t guest_vlan;
+ /*
+ * The guest VLAN for the function being configured. This
+ * field's format is same as 802.1Q Tag's Tag Control
+ * Information (TCI) format that includes both Priority Code
+ * Point (PCP) and VLAN Identifier (VID).
+ */
+ uint16_t async_event_cr;
+ /*
+ * ID of the target completion ring for receiving asynchronous
+ * event completions. If this field is not valid, then the HWRM
+ * shall use the default completion ring of the function that is
+ * being configured as the target completion ring for providing
+ * any asynchronous event completions for that function. If this
+ * field is valid, then the HWRM shall use the completion ring
+ * identified by this ID as the target completion ring for
+ * providing any asynchronous event completions for the function
+ * that is being configured.
+ */
+ uint8_t dflt_mac_addr[6];
+ /*
+ * This value is the current MAC address requested by the VF
+ * driver to be configured on this VF. A value of
+ * 00-00-00-00-00-00 indicates no MAC address configuration is
+ * requested by the VF driver. The parent PF driver may reject
+ * or overwrite this MAC address.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_vf_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_qcaps */
+/*
+ * Description: This command returns capabilities of a function. The input FID
+ * value is used to indicate what function is being queried. This allows a
+ * physical function driver to query virtual functions that are children of the
+ * physical function. The output FID value is needed to configure Rings and
+ * MSI-X vectors so their DMA operations appear correctly on the PCI bus.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_qcaps_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being queried. 0xFF...
+ * (All Fs) if the query is for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (80 bytes) */
+struct hwrm_func_qcaps_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t fid;
+ /*
+ * FID value. This value is used to identify operations on the
+ * PCI bus as belonging to a particular PCI function.
+ */
+ uint16_t port_id;
+ /*
+ * Port ID of port that this function is associated with. Valid
+ * only for the PF. 0xFF... (All Fs) if this function is not
+ * associated with any port. 0xFF... (All Fs) if this function
+ * is called from a VF.
+ */
+ uint32_t flags;
+ /* If 1, then Push mode is supported on this function. */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PUSH_MODE_SUPPORTED 0x1UL
+ /*
+ * If 1, then the global MSI-X auto-masking is enabled for the
+ * device.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_GLOBAL_MSIX_AUTOMASKING 0x2UL
+ /*
+ * If 1, then the Precision Time Protocol (PTP) processing is
+ * supported on this function. The HWRM should enable PTP on
+ * only a single Physical Function (PF) per port.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PTP_SUPPORTED 0x4UL
+ /*
+ * If 1, then RDMA over Converged Ethernet (RoCE) v1 is
+ * supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ROCE_V1_SUPPORTED 0x8UL
+ /*
+ * If 1, then RDMA over Converged Ethernet (RoCE) v2 is
+ * supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ROCE_V2_SUPPORTED 0x10UL
+ /*
+ * If 1, then control and configuration of WoL magic packet are
+ * supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_WOL_MAGICPKT_SUPPORTED 0x20UL
+ /*
+ * If 1, then control and configuration of bitmap pattern packet
+ * are supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_WOL_BMP_SUPPORTED 0x40UL
+ /*
+ * If set to 1, then the control and configuration of rate limit
+ * of an allocated TX ring on the queried function is supported.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_TX_RING_RL_SUPPORTED 0x80UL
+ /*
+ * If 1, then control and configuration of minimum and maximum
+ * bandwidths are supported on the queried function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_TX_BW_CFG_SUPPORTED 0x100UL
+ /*
+ * If the query is for a VF, then this flag shall be ignored. If
+ * this query is for a PF and this flag is set to 1, then the PF
+ * has the capability to set the rate limits on the TX rings of
+ * its children VFs. If this query is for a PF and this flag is
+ * set to 0, then the PF does not have the capability to set the
+ * rate limits on the TX rings of its children VFs.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_VF_TX_RING_RL_SUPPORTED 0x200UL
+ /*
+ * If the query is for a VF, then this flag shall be ignored. If
+ * this query is for a PF and this flag is set to 1, then the PF
+ * has the capability to set the minimum and/or maximum
+ * bandwidths for its children VFs. If this query is for a PF
+ * and this flag is set to 0, then the PF does not have the
+ * capability to set the minimum or maximum bandwidths for its
+ * children VFs.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_VF_BW_CFG_SUPPORTED 0x400UL
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then standard TX ring mode is supported on the
+ * queried function. If set to 0, then standard TX ring mode is
+ * not available on the queried function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_STD_TX_RING_MODE_SUPPORTED 0x800UL
+ uint8_t mac_address[6];
+ /*
+ * This value is current MAC address configured for this
+ * function. A value of 00-00-00-00-00-00 indicates no MAC
+ * address is currently configured.
+ */
+ uint16_t max_rsscos_ctx;
+ /*
+ * The maximum number of RSS/COS contexts that can be allocated
+ * to the function.
+ */
+ uint16_t max_cmpl_rings;
+ /*
+ * The maximum number of completion rings that can be allocated
+ * to the function.
+ */
+ uint16_t max_tx_rings;
+ /*
+ * The maximum number of transmit rings that can be allocated to
+ * the function.
+ */
+ uint16_t max_rx_rings;
+ /*
+ * The maximum number of receive rings that can be allocated to
+ * the function.
+ */
+ uint16_t max_l2_ctxs;
+ /*
+ * The maximum number of L2 contexts that can be allocated to
+ * the function.
+ */
+ uint16_t max_vnics;
+ /*
+ * The maximum number of VNICs that can be allocated to the
+ * function.
+ */
+ uint16_t first_vf_id;
+ /*
+ * The identifier for the first VF enabled on a PF. This is
+ * valid only on the PF with SR-IOV enabled. 0xFF... (All Fs) if
+ * this command is called on a PF with SR-IOV disabled or on a
+ * VF.
+ */
+ uint16_t max_vfs;
+ /*
+ * The maximum number of VFs that can be allocated to the
+ * function. This is valid only on the PF with SR-IOV enabled.
+ * 0xFF... (All Fs) if this command is called on a PF with SR-
+ * IOV disabled or on a VF.
+ */
+ uint16_t max_stat_ctx;
+ /*
+ * The maximum number of statistic contexts that can be
+ * allocated to the function.
+ */
+ uint32_t max_encap_records;
+ /*
+ * The maximum number of Encapsulation records that can be
+ * offloaded by this function.
+ */
+ uint32_t max_decap_records;
+ /*
+ * The maximum number of decapsulation records that can be
+ * offloaded by this function.
+ */
+ uint32_t max_tx_em_flows;
+ /*
+ * The maximum number of Exact Match (EM) flows that can be
+ * offloaded by this function on the TX side.
+ */
+ uint32_t max_tx_wm_flows;
+ /*
+ * The maximum number of Wildcard Match (WM) flows that can be
+ * offloaded by this function on the TX side.
+ */
+ uint32_t max_rx_em_flows;
+ /*
+ * The maximum number of Exact Match (EM) flows that can be
+ * offloaded by this function on the RX side.
+ */
+ uint32_t max_rx_wm_flows;
+ /*
+ * The maximum number of Wildcard Match (WM) flows that can be
+ * offloaded by this function on the RX side.
+ */
+ uint32_t max_mcast_filters;
+ /*
+ * The maximum number of multicast filters that can be supported
+ * by this function on the RX side.
+ */
+ uint32_t max_flow_id;
+ /*
+ * The maximum value of flow_id that can be supported in
+ * completion records.
+ */
+ uint32_t max_hw_ring_grps;
+ /*
+ * The maximum number of HW ring groups that can be supported on
+ * this function.
+ */
+ uint16_t max_sp_tx_rings;
+ /*
+ * The maximum number of strict priority transmit rings that can
+ * be allocated to the function. This number indicates the
+ * maximum number of TX rings that can be assigned strict
+ * priorities out of the maximum number of TX rings that can be
+ * allocated (max_tx_rings) to the function.
+ */
+ uint8_t unused_0;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_qcfg */
+/*
+ * Description: This command returns the current configuration of a function.
+ * The input FID value is used to indicate what function is being queried. This
+ * allows a physical function driver to query virtual functions that are
+ * children of the physical function. The output FID value is needed to
+ * configure Rings and MSI-X vectors so their DMA operations appear correctly on
+ * the PCI bus. This command should be called by every driver after
+ * 'hwrm_func_cfg' to get the actual number of resources allocated by the HWRM.
+ * The values returned by hwrm_func_qcfg are the values the driver shall use.
+ * These values may be different than what was originally requested in the
+ * 'hwrm_func_cfg' command.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being queried. 0xFF...
+ * (All Fs) if the query is for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (72 bytes) */
+struct hwrm_func_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t fid;
+ /*
+ * FID value. This value is used to identify operations on the
+ * PCI bus as belonging to a particular PCI function.
+ */
+ uint16_t port_id;
+ /*
+ * Port ID of port that this function is associated with.
+ * 0xFF... (All Fs) if this function is not associated with any
+ * port.
+ */
+ uint16_t vlan;
+ /*
+ * This value is the current VLAN setting for this function. The
+ * value of 0 for this field indicates no priority tagging or
+ * VLAN is used. This field's format is same as 802.1Q Tag's Tag
+ * Control Information (TCI) format that includes both Priority
+ * Code Point (PCP) and VLAN Identifier (VID).
+ */
+ uint16_t flags;
+ /*
+ * If 1, then magic packet based Out-Of-Box WoL is enabled on
+ * the port associated with this function.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_OOB_WOL_MAGICPKT_ENABLED 0x1UL
+ /*
+ * If 1, then bitmap pattern based Out-Of-Box WoL packet is
+ * enabled on the port associated with this function.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_OOB_WOL_BMP_ENABLED 0x2UL
+ /*
+ * If set to 1, then FW based DCBX agent is enabled and running
+ * on the port associated with this function. If set to 0, then
+ * DCBX agent is not running in the firmware.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_FW_DCBX_AGENT_ENABLED 0x4UL
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then standard TX ring mode is enabled on the
+ * queried function. If set to 0, then the standard TX ring mode
+ * is disabled on the queried function. In this extended TX ring
+ * resource mode, the minimum and maximum bandwidth settings are
+ * not supported to allow the allocation of TX rings to span
+ * multiple scheduler nodes.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_STD_TX_RING_MODE_ENABLED 0x8UL
+ /*
+ * If set to 1 then FW based LLDP agent is enabled and running
+ * on the port associated with this function. If set to 0 then
+ * the LLDP agent is not running in the firmware.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_FW_LLDP_AGENT_ENABLED 0x10UL
+ /*
+ * If set to 1, then multi-host mode is active for this
+ * function. If set to 0, then multi-host mode is inactive for
+ * this function or not applicable for this device.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_MULTI_HOST 0x20UL
+ uint8_t mac_address[6];
+ /*
+ * This value is current MAC address configured for this
+ * function. A value of 00-00-00-00-00-00 indicates no MAC
+ * address is currently configured.
+ */
+ uint16_t pci_id;
+ /*
+ * This value is current PCI ID of this function. If ARI is
+ * enabled, then it is Bus Number (8b):Function Number(8b).
+ * Otherwise, it is Bus Number (8b):Device Number (4b):Function
+ * Number(4b). If multi-host mode is active, the 4 lsb will
+ * indicate the PF index for this function.
+ */
+ uint16_t alloc_rsscos_ctx;
+ /*
+ * The number of RSS/COS contexts currently allocated to the
+ * function.
+ */
+ uint16_t alloc_cmpl_rings;
+ /*
+ * The number of completion rings currently allocated to the
+ * function. This does not include the rings allocated to any
+ * children functions if any.
+ */
+ uint16_t alloc_tx_rings;
+ /*
+ * The number of transmit rings currently allocated to the
+ * function. This does not include the rings allocated to any
+ * children functions if any.
+ */
+ uint16_t alloc_rx_rings;
+ /*
+ * The number of receive rings currently allocated to the
+ * function. This does not include the rings allocated to any
+ * children functions if any.
+ */
+ uint16_t alloc_l2_ctx;
+ /* The allocated number of L2 contexts to the function. */
+ uint16_t alloc_vnics;
+ /* The allocated number of vnics to the function. */
+ uint16_t mtu;
+ /*
+ * The maximum transmission unit of the function. For rings
+ * allocated on this function, this default value is used if
+ * ring MTU is not specified.
+ */
+ uint16_t mru;
+ /*
+ * The maximum receive unit of the function. For vnics allocated
+ * on this function, this default value is used if vnic MRU is
+ * not specified.
+ */
+ uint16_t stat_ctx_id;
+ /* The statistics context assigned to a function. */
+ uint8_t port_partition_type;
+ /*
+ * The HWRM shall return Unknown value for this field when this
+ * command is used to query VF's configuration.
+ */
+ /* Single physical function */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_SPF 0x0UL
+ /* Multiple physical functions */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_MPFS 0x1UL
+ /* Network Partitioning 1.0 */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR1_0 0x2UL
+ /* Network Partitioning 1.5 */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR1_5 0x3UL
+ /* Network Partitioning 2.0 */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR2_0 0x4UL
+ /* Unknown */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_UNKNOWN 0xffUL
+ uint8_t port_pf_cnt;
+ /*
+ * This field will indicate number of physical functions on this
+ * port_partition. HWRM shall return unavail (i.e. value of 0)
+ * for this field when this command is used to query VF's
+ * configuration or from older firmware that doesn't support
+ * this field.
+ */
+ /* number of PFs is not available */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PF_CNT_UNAVAIL 0x0UL
+ uint16_t dflt_vnic_id;
+ /* The default VNIC ID assigned to a function that is being queried. */
+ uint16_t max_mtu_configured;
+ /*
+ * This value specifies the MAX MTU that can be configured by
+ * host drivers. This 'max_mtu_configure' can be HW max MTU or
+ * OEM applications specified value. Host drivers can't
+ * configure the MTU greater than this value. Host drivers
+ * should read this value prior to configuring the MTU. FW will
+ * fail the host request with MTU greater than
+ * 'max_mtu_configured'.
+ */
+ uint32_t min_bw;
+ /*
+ * Minimum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device. A value of 0 indicates
+ * the minimum bandwidth is not configured.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_MASK 0xfffffffUL
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BITS (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BYTES (0x1UL << 28)
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_LAST \
+ FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_MASK 0xe0000000UL
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_MEGA (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_KILO (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_BASE (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_GIGA (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_INVALID (0x7UL << 29)
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_LAST \
+ FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t max_bw;
+ /*
+ * Maximum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device. A value of 0 indicates
+ * that the maximum bandwidth is not configured.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_MASK 0xfffffffUL
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BITS (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BYTES (0x1UL << 28)
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_LAST \
+ FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_MASK 0xe0000000UL
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_MEGA (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_KILO (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_BASE (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_GIGA (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_INVALID (0x7UL << 29)
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_LAST \
+ FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t evb_mode;
+ /*
+ * This value indicates the Edge virtual bridge mode for the
+ * domain that this function belongs to.
+ */
+ /* No Edge Virtual Bridging (EVB) */
+ #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_NO_EVB 0x0UL
+ /* Virtual Ethernet Bridge (VEB) */
+ #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEB 0x1UL
+ /* Virtual Ethernet Port Aggregator (VEPA) */
+ #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEPA 0x2UL
+ uint8_t unused_0;
+ uint16_t alloc_vfs;
+ /*
+ * The number of VFs that are allocated to the function. This is
+ * valid only on the PF with SR-IOV enabled. 0xFF... (All Fs) if
+ * this command is called on a PF with SR-IOV disabled or on a
+ * VF.
+ */
+ uint32_t alloc_mcast_filters;
+ /*
+ * The number of allocated multicast filters for this function
+ * on the RX side.
+ */
+ uint32_t alloc_hw_ring_grps;
+ /* The number of allocated HW ring groups for this function. */
+ uint16_t alloc_sp_tx_rings;
+ /*
+ * The number of strict priority transmit rings out of currently
+ * allocated TX rings to the function (alloc_tx_rings).
+ */
+ uint8_t unused_1;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vlan_qcfg */
+/*
+ * Description: This command should be called by PF driver to get the current
+ * C-TAG, S-TAG and correcponsing PCP and TPID values configured for the
+ * function.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_vlan_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. If set
+ * to 0xFF... (All Fs), then the configuration is for the
+ * requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (40 bytes) */
+struct hwrm_func_vlan_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+ uint16_t stag_vid;
+ /* S-TAG VLAN identifier configured for the function. */
+ uint8_t stag_pcp;
+ /* S-TAG PCP value configured for the function. */
+ uint8_t unused_4;
+ uint16_t stag_tpid;
+ /*
+ * S-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint16_t ctag_vid;
+ /* C-TAG VLAN identifier configured for the function. */
+ uint8_t ctag_pcp;
+ /* C-TAG PCP value configured for the function. */
+ uint8_t unused_5;
+ uint16_t ctag_tpid;
+ /*
+ * C-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint32_t rsvd2;
+ /* Future use. */
+ uint32_t rsvd3;
+ /* Future use. */
+ uint32_t unused_6;
+} __attribute__((packed));
+
+/* hwrm_func_vlan_cfg */
+/*
+ * Description: This command allows PF driver to configure C-TAG, S-TAG and
+ * corresponding PCP and TPID values for a function.
+ */
+/* Input (48 bytes) */
+struct hwrm_func_vlan_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. If set
+ * to 0xFF... (All Fs), then the configuration is for the
+ * requesting function.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t enables;
+ /* This bit must be '1' for the stag_vid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_VID 0x1UL
+ /* This bit must be '1' for the ctag_vid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_VID 0x2UL
+ /* This bit must be '1' for the stag_pcp field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_PCP 0x4UL
+ /* This bit must be '1' for the ctag_pcp field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_PCP 0x8UL
+ /* This bit must be '1' for the stag_tpid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_TPID 0x10UL
+ /* This bit must be '1' for the ctag_tpid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_TPID 0x20UL
+ uint16_t stag_vid;
+ /* S-TAG VLAN identifier configured for the function. */
+ uint8_t stag_pcp;
+ /* S-TAG PCP value configured for the function. */
+ uint8_t unused_2;
+ uint16_t stag_tpid;
+ /*
+ * S-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint16_t ctag_vid;
+ /* C-TAG VLAN identifier configured for the function. */
+ uint8_t ctag_pcp;
+ /* C-TAG PCP value configured for the function. */
+ uint8_t unused_3;
+ uint16_t ctag_tpid;
+ /*
+ * C-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint32_t rsvd1;
+ /* Future use. */
+ uint32_t rsvd2;
+ /* Future use. */
+ uint32_t unused_4;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_vlan_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_cfg */
+/*
+ * Description: This command allows configuration of a PF by the corresponding
+ * PF driver. This command also allows configuration of a child VF by its parent
+ * PF driver. The input FID value is used to indicate what function is being
+ * configured. This allows a PF driver to configure the PF owned by itself or a
+ * virtual function that is a child of the PF. This command allows to reserve
+ * resources for a VF by its parent PF. To reverse the process, the command
+ * should be called with all enables flags cleared for resources. This will free
+ * allocated resources for the VF and return them to the resource pool. If this
+ * command is requested by a VF driver to configure or reserve resources, then
+ * the HWRM shall fail this command. If default MAC address and/or VLAN are
+ * provided in this command, then the HWRM shall set up appropriate MAC/VLAN
+ * filters for the function that is being configured. If source properties
+ * checks are enabled and default MAC address and/or IP address are provided in
+ * this command, then the HWRM shall set appropriate source property checks
+ * based on provided MAC and/or IP addresses. The parent PF driver should not
+ * set MTU/MRU for a VF using this command. This is to allow MTU/MRU setting by
+ * the VF driver. If the MTU or MRU for a VF is set by the PF driver, then the
+ * HWRM should ignore it. A function's MTU/MRU should be set prior to allocating
+ * RX VNICs or TX rings. A PF driver calls hwrm_func_cfg to allocate resources
+ * for itself or its children VFs. All function drivers shall call hwrm_func_cfg
+ * to reserve resources. A request to hwrm_func_cfg may not be fully granted;
+ * that is, a request for resources may be larger than what can be supported by
+ * the device and the HWRM will allocate the best set of resources available,
+ * but that may be less than requested. If all the amounts requested could not
+ * be fulfilled, the HWRM shall allocate what it could and return a status code
+ * of success. A function driver should call hwrm_func_qcfg immediately after
+ * hwrm_func_cfg to determine what resources were assigned to the configured
+ * function. A call by a PF driver to hwrm_func_cfg to allocate resources for
+ * itself shall only allocate resources for the PF driver to use, not for its
+ * children VFs. Likewise, a call to hwrm_func_qcfg shall return the resources
+ * available for the PF driver to use, not what is available to its children
+ * VFs.
+ */
+/* Input (88 bytes) */
+struct hwrm_func_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. If set
+ * to 0xFF... (All Fs), then the the configuration is for the
+ * requesting function.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the function is disabled with source
+ * MAC address check. This is an anti-spoofing check. If this
+ * flag is set, then the function shall be configured to
+ * disallow transmission of frames with the source MAC address
+ * that is configured for this function.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_DISABLE 0x1UL
+ /*
+ * When this bit is '1', the function is enabled with source MAC
+ * address check. This is an anti-spoofing check. If this flag
+ * is set, then the function shall be configured to allow
+ * transmission of frames with the source MAC address that is
+ * configured for this function.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_ENABLE 0x2UL
+ /* reserved */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_MASK 0x1fcUL
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_SFT 2
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then standard TX ring mode is requested to be
+ * enabled on the function being configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_ENABLE 0x200UL
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then the standard TX ring mode is requested to be
+ * disabled on the function being configured. In this extended
+ * TX ring resource mode, the minimum and maximum bandwidth
+ * settings are not supported to allow the allocation of TX
+ * rings to span multiple scheduler nodes.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_DISABLE 0x400UL
+ /*
+ * If this bit is set, virtual mac address configured in this
+ * command will be persistent over warm boot.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_VIRT_MAC_PERSIST 0x800UL
+ /*
+ * This bit only applies to the VF. If this bit is set, the
+ * statistic context counters will not be cleared when the
+ * statistic context is freed or a function reset is called on
+ * VF. This bit will be cleared when the PF is unloaded or a
+ * function reset is called on the PF.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_NO_AUTOCLEAR_STATISTIC 0x1000UL
+ /*
+ * This bit requests that the firmware test to see if all the
+ * assets requested in this command (i.e. number of TX rings)
+ * are available. The firmware will return an error if the
+ * requested assets are not available. The firwmare will NOT
+ * reserve the assets if they are available.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_TX_ASSETS_TEST 0x2000UL
+ uint32_t enables;
+ /* This bit must be '1' for the mtu field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MTU 0x1UL
+ /* This bit must be '1' for the mru field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MRU 0x2UL
+ /*
+ * This bit must be '1' for the num_rsscos_ctxs field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RSSCOS_CTXS 0x4UL
+ /*
+ * This bit must be '1' for the num_cmpl_rings field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_CMPL_RINGS 0x8UL
+ /* This bit must be '1' for the num_tx_rings field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_TX_RINGS 0x10UL
+ /* This bit must be '1' for the num_rx_rings field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RX_RINGS 0x20UL
+ /* This bit must be '1' for the num_l2_ctxs field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_L2_CTXS 0x40UL
+ /* This bit must be '1' for the num_vnics field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_VNICS 0x80UL
+ /*
+ * This bit must be '1' for the num_stat_ctxs field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_STAT_CTXS 0x100UL
+ /*
+ * This bit must be '1' for the dflt_mac_addr field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_MAC_ADDR 0x200UL
+ /* This bit must be '1' for the dflt_vlan field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_VLAN 0x400UL
+ /* This bit must be '1' for the dflt_ip_addr field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_IP_ADDR 0x800UL
+ /* This bit must be '1' for the min_bw field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MIN_BW 0x1000UL
+ /* This bit must be '1' for the max_bw field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MAX_BW 0x2000UL
+ /*
+ * This bit must be '1' for the async_event_cr field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_ASYNC_EVENT_CR 0x4000UL
+ /*
+ * This bit must be '1' for the vlan_antispoof_mode field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_VLAN_ANTISPOOF_MODE 0x8000UL
+ /*
+ * This bit must be '1' for the allowed_vlan_pris field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_ALLOWED_VLAN_PRIS 0x10000UL
+ /* This bit must be '1' for the evb_mode field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_EVB_MODE 0x20000UL
+ /*
+ * This bit must be '1' for the num_mcast_filters field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_MCAST_FILTERS 0x40000UL
+ /*
+ * This bit must be '1' for the num_hw_ring_grps field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_HW_RING_GRPS 0x80000UL
+ uint16_t mtu;
+ /*
+ * The maximum transmission unit of the function. The HWRM
+ * should make sure that the mtu of the function does not exceed
+ * the mtu of the physical port that this function is associated
+ * with. In addition to configuring mtu per function, it is
+ * possible to configure mtu per transmit ring. By default, the
+ * mtu of each transmit ring associated with a function is equal
+ * to the mtu of the function. The HWRM should make sure that
+ * the mtu of each transmit ring that is assigned to a function
+ * has a valid mtu.
+ */
+ uint16_t mru;
+ /*
+ * The maximum receive unit of the function. The HWRM should
+ * make sure that the mru of the function does not exceed the
+ * mru of the physical port that this function is associated
+ * with. In addition to configuring mru per function, it is
+ * possible to configure mru per vnic. By default, the mru of
+ * each vnic associated with a function is equal to the mru of
+ * the function. The HWRM should make sure that the mru of each
+ * vnic that is assigned to a function has a valid mru.
+ */
+ uint16_t num_rsscos_ctxs;
+ /* The number of RSS/COS contexts requested for the function. */
+ uint16_t num_cmpl_rings;
+ /*
+ * The number of completion rings requested for the function.
+ * This does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_tx_rings;
+ /*
+ * The number of transmit rings requested for the function. This
+ * does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_rx_rings;
+ /*
+ * The number of receive rings requested for the function. This
+ * does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_l2_ctxs;
+ /* The requested number of L2 contexts for the function. */
+ uint16_t num_vnics;
+ /* The requested number of vnics for the function. */
+ uint16_t num_stat_ctxs;
+ /* The requested number of statistic contexts for the function. */
+ uint16_t num_hw_ring_grps;
+ /*
+ * The number of HW ring groups that should be reserved for this
+ * function.
+ */
+ uint8_t dflt_mac_addr[6];
+ /* The default MAC address for the function being configured. */
+ uint16_t dflt_vlan;
+ /*
+ * The default VLAN for the function being configured. This
+ * field's format is same as 802.1Q Tag's Tag Control
+ * Information (TCI) format that includes both Priority Code
+ * Point (PCP) and VLAN Identifier (VID).
+ */
+ uint32_t dflt_ip_addr[4];
+ /*
+ * The default IP address for the function being configured.
+ * This address is only used in enabling source property check.
+ */
+ uint32_t min_bw;
+ /*
+ * Minimum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_MASK 0xfffffffUL
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BITS (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES (0x1UL << 28)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_LAST \
+ FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MASK 0xe0000000UL
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MEGA (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_KILO (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_BASE (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_GIGA (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID (0x7UL << 29)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_LAST \
+ FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t max_bw;
+ /*
+ * Maximum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_MASK 0xfffffffUL
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BITS (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES (0x1UL << 28)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_LAST \
+ FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MASK 0xe0000000UL
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_KILO (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_BASE (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID (0x7UL << 29)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
+ FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint16_t async_event_cr;
+ /*
+ * ID of the target completion ring for receiving asynchronous
+ * event completions. If this field is not valid, then the HWRM
+ * shall use the default completion ring of the function that is
+ * being configured as the target completion ring for providing
+ * any asynchronous event completions for that function. If this
+ * field is valid, then the HWRM shall use the completion ring
+ * identified by this ID as the target completion ring for
+ * providing any asynchronous event completions for the function
+ * that is being configured.
+ */
+ uint8_t vlan_antispoof_mode;
+ /* VLAN Anti-spoofing mode. */
+ /* No VLAN anti-spoofing checks are enabled */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_NOCHECK 0x0UL
+ /* Validate VLAN against the configured VLAN(s) */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_VALIDATE_VLAN 0x1UL
+ /* Insert VLAN if it does not exist, otherwise discard */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_IF_VLANDNE 0x2UL
+ /*
+ * Insert VLAN if it does not exist, override
+ * VLAN if it exists
+ */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_OR_OVERRIDE_VLAN \
+ 0x3UL
+ uint8_t allowed_vlan_pris;
+ /*
+ * This bit field defines VLAN PRIs that are allowed on this
+ * function. If nth bit is set, then VLAN PRI n is allowed on
+ * this function.
+ */
+ uint8_t evb_mode;
+ /*
+ * The HWRM shall allow a PF driver to change EVB mode for the
+ * partition it belongs to. The HWRM shall not allow a VF driver
+ * to change the EVB mode. The HWRM shall take into account the
+ * switching of EVB mode from one to another and reconfigure
+ * hardware resources as appropriately. The switching from VEB
+ * to VEPA mode requires the disabling of the loopback traffic.
+ * Additionally, source knock outs are handled differently in
+ * VEB and VEPA modes.
+ */
+ /* No Edge Virtual Bridging (EVB) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_NO_EVB 0x0UL
+ /* Virtual Ethernet Bridge (VEB) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEB 0x1UL
+ /* Virtual Ethernet Port Aggregator (VEPA) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEPA 0x2UL
+ uint8_t unused_2;
+ uint16_t num_mcast_filters;
+ /*
+ * The number of multicast filters that should be reserved for
+ * this function on the RX side.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_qstats */
+/*
+ * Description: This command returns statistics of a function. The input FID
+ * value is used to indicate what function is being queried. This allows a
+ * physical function driver to query virtual functions that are children of the
+ * physical function. The HWRM shall return any unsupported counter with a value
+ * of 0xFFFFFFFF for 32-bit counters and 0xFFFFFFFFFFFFFFFF for 64-bit counters.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_qstats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being queried. 0xFF...
+ * (All Fs) if the query is for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (176 bytes) */
+struct hwrm_func_qstats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint64_t tx_ucast_pkts;
+ /* Number of transmitted unicast packets on the function. */
+ uint64_t tx_mcast_pkts;
+ /* Number of transmitted multicast packets on the function. */
+ uint64_t tx_bcast_pkts;
+ /* Number of transmitted broadcast packets on the function. */
+ uint64_t tx_err_pkts;
+ /*
+ * Number of transmitted packets that were discarded due to
+ * internal NIC resource problems. For transmit, this can only
+ * happen if TMP is configured to allow dropping in HOL blocking
+ * conditions, which is not a normal configuration.
+ */
+ uint64_t tx_drop_pkts;
+ /*
+ * Number of dropped packets on transmit path on the function.
+ * These are packets that have been marked for drop by the TE
+ * CFA block or are packets that exceeded the transmit MTU limit
+ * for the function.
+ */
+ uint64_t tx_ucast_bytes;
+ /* Number of transmitted bytes for unicast traffic on the function. */
+ uint64_t tx_mcast_bytes;
+ /*
+ * Number of transmitted bytes for multicast traffic on the
+ * function.
+ */
+ uint64_t tx_bcast_bytes;
+ /*
+ * Number of transmitted bytes for broadcast traffic on the
+ * function.
+ */
+ uint64_t rx_ucast_pkts;
+ /* Number of received unicast packets on the function. */
+ uint64_t rx_mcast_pkts;
+ /* Number of received multicast packets on the function. */
+ uint64_t rx_bcast_pkts;
+ /* Number of received broadcast packets on the function. */
+ uint64_t rx_err_pkts;
+ /*
+ * Number of received packets that were discarded on the
+ * function due to resource limitations. This can happen for 3
+ * reasons. # The BD used for the packet has a bad format. #
+ * There were no BDs available in the ring for the packet. #
+ * There were no BDs available on-chip for the packet.
+ */
+ uint64_t rx_drop_pkts;
+ /*
+ * Number of dropped packets on received path on the function.
+ * These are packets that have been marked for drop by the RE
+ * CFA.
+ */
+ uint64_t rx_ucast_bytes;
+ /* Number of received bytes for unicast traffic on the function. */
+ uint64_t rx_mcast_bytes;
+ /* Number of received bytes for multicast traffic on the function. */
+ uint64_t rx_bcast_bytes;
+ /* Number of received bytes for broadcast traffic on the function. */
+ uint64_t rx_agg_pkts;
+ /* Number of aggregated unicast packets on the function. */
+ uint64_t rx_agg_bytes;
+ /* Number of aggregated unicast bytes on the function. */
+ uint64_t rx_agg_events;
+ /* Number of aggregation events on the function. */
+ uint64_t rx_agg_aborts;
+ /* Number of aborted aggregations on the function. */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_clr_stats */
+/*
+ * Description: This command clears statistics of a function. The input FID
+ * value is used to indicate what function's statistics is being cleared. This
+ * allows a physical function driver to clear statistics of virtual functions
+ * that are children of the physical function.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_clr_stats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function. 0xFF... (All Fs) if the query is
+ * for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_clr_stats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vf_resc_free */
+/* Description: This command frees resources of a vf. */
+/* Input (24 bytes) */
+struct hwrm_func_vf_resc_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_vf_resc_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vf_vnic_ids_query */
+/* Description: This command is used to query vf vnic ids. */
+/* Input (32 bytes) */
+struct hwrm_func_vf_vnic_ids_query_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t max_vnic_id_cnt;
+ /* Max number of vnic ids in vnic id table */
+ uint64_t vnic_id_tbl_addr;
+ /* This is the address for VF VNIC ID table */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_vf_vnic_ids_query_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t vnic_id_cnt;
+ /*
+ * Actual number of vnic ids Each VNIC ID is written as a 32-bit
+ * number.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_drv_rgtr */
+/*
+ * Description: This command is used by the function driver to register its
+ * information with the HWRM. A function driver shall implement this command. A
+ * function driver shall use this command during the driver initialization right
+ * after the HWRM version discovery and default ring resources allocation.
+ */
+/* Input (80 bytes) */
+struct hwrm_func_drv_rgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the function driver is requesting all
+ * requests from its children VF drivers to be forwarded to
+ * itself. This flag can only be set by the PF driver. If a VF
+ * driver sets this flag, it should be ignored by the HWRM.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_ALL_MODE 0x1UL
+ /*
+ * When this bit is '1', the function is requesting none of the
+ * requests from its children VF drivers to be forwarded to
+ * itself. This flag can only be set by the PF driver. If a VF
+ * driver sets this flag, it should be ignored by the HWRM.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_NONE_MODE 0x2UL
+ uint32_t enables;
+ /* This bit must be '1' for the os_type field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_OS_TYPE 0x1UL
+ /* This bit must be '1' for the ver field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VER 0x2UL
+ /* This bit must be '1' for the timestamp field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_TIMESTAMP 0x4UL
+ /* This bit must be '1' for the vf_req_fwd field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VF_INPUT_FWD 0x8UL
+ /*
+ * This bit must be '1' for the async_event_fwd field to be
+ * configured.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_ASYNC_EVENT_FWD 0x10UL
+ uint16_t os_type;
+ /*
+ * This value indicates the type of OS. The values are based on
+ * CIM_OperatingSystem.mof file as published by the DMTF.
+ */
+ /* Unknown */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_UNKNOWN 0x0UL
+ /* Other OS not listed below. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_OTHER 0x1UL
+ /* MSDOS OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_MSDOS 0xeUL
+ /* Windows OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WINDOWS 0x12UL
+ /* Solaris OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_SOLARIS 0x1dUL
+ /* Linux OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_LINUX 0x24UL
+ /* FreeBSD OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_FREEBSD 0x2aUL
+ /* VMware ESXi OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_ESXI 0x68UL
+ /* Microsoft Windows 8 64-bit OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN864 0x73UL
+ /* Microsoft Windows Server 2012 R2 OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN2012R2 0x74UL
+ uint8_t ver_maj;
+ /* This is the major version of the driver. */
+ uint8_t ver_min;
+ /* This is the minor version of the driver. */
+ uint8_t ver_upd;
+ /* This is the update version of the driver. */
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint32_t timestamp;
+ /*
+ * This is a 32-bit timestamp provided by the driver for keep
+ * alive. The timestamp is in multiples of 1ms.
+ */
+ uint32_t unused_2;
+ uint32_t vf_req_fwd[8];
+ /*
+ * This is a 256-bit bit mask provided by the PF driver for
+ * letting the HWRM know what commands issued by the VF driver
+ * to the HWRM should be forwarded to the PF driver. Nth bit
+ * refers to the Nth req_type. Setting Nth bit to 1 indicates
+ * that requests from the VF driver with req_type equal to N
+ * shall be forwarded to the parent PF driver. This field is not
+ * valid for the VF driver.
+ */
+ uint32_t async_event_fwd[8];
+ /*
+ * This is a 256-bit bit mask provided by the function driver
+ * (PF or VF driver) to indicate the list of asynchronous event
+ * completions to be forwarded. Nth bit refers to the Nth
+ * event_id. Setting Nth bit to 1 by the function driver shall
+ * result in the HWRM forwarding asynchronous event completion
+ * with event_id equal to N. If all bits are set to 0 (value of
+ * 0), then the HWRM shall not forward any asynchronous event
+ * completion to this function driver.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_drv_rgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_drv_unrgtr */
+/*
+ * Description: This command is used by the function driver to un register with
+ * the HWRM. A function driver shall implement this command. A function driver
+ * shall use this command during the driver unloading.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_drv_unrgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the function driver is notifying the
+ * HWRM to prepare for the shutdown.
+ */
+ #define HWRM_FUNC_DRV_UNRGTR_INPUT_FLAGS_PREPARE_FOR_SHUTDOWN 0x1UL
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_drv_unrgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_buf_rgtr */
+/*
+ * Description: This command is used by the PF driver to register buffers used
+ * in the PF-VF communication with the HWRM. The PF driver uses this command to
+ * register buffers for each PF-VF channel. A parent PF may issue this command
+ * per child VF. If VF ID is not valid, then this command is used to register
+ * buffers for all children VFs of the PF.
+ */
+/* Input (128 bytes) */
+struct hwrm_func_buf_rgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id field to be configured. */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_ENABLES_VF_ID 0x1UL
+ /* This bit must be '1' for the err_buf_addr field to be configured. */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_ENABLES_ERR_BUF_ADDR 0x2UL
+ uint16_t vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint16_t req_buf_num_pages;
+ /*
+ * This field represents the number of pages used for request
+ * buffer(s).
+ */
+ uint16_t req_buf_page_size;
+ /* This field represents the page size used for request buffer(s). */
+ /* 16 bytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_16B 0x4UL
+ /* 4 Kbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_4K 0xcUL
+ /* 8 Kbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_8K 0xdUL
+ /* 64 Kbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_64K 0x10UL
+ /* 2 Mbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_2M 0x15UL
+ /* 4 Mbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_4M 0x16UL
+ /* 1 Gbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_1G 0x1eUL
+ uint16_t req_buf_len;
+ /* The length of the request buffer per VF in bytes. */
+ uint16_t resp_buf_len;
+ /* The length of the response buffer in bytes. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint64_t req_buf_page_addr[10];
+ /* This field represents the page address of req buffer. */
+ uint64_t error_buf_addr;
+ /*
+ * This field is used to receive the error reporting from the
+ * chipset. Only applicable for PFs.
+ */
+ uint64_t resp_buf_addr;
+ /* This field is used to receive the response forwarded by the HWRM. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_buf_rgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_buf_unrgtr */
+/*
+ * Description: This command is used by the PF driver to unregister buffers used
+ * in the PF-VF communication with the HWRM. The PF driver uses this command to
+ * unregister buffers for PF-VF communication. A parent PF may issue this
+ * command to unregister buffers for communication between the PF and a specific
+ * VF. If the VF ID is not valid, then this command is used to unregister
+ * buffers used for communications with all children VFs of the PF.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_buf_unrgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id field to be configured. */
+ #define HWRM_FUNC_BUF_UNRGTR_INPUT_ENABLES_VF_ID 0x1UL
+ uint16_t vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_buf_unrgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_drv_qver */
+/*
+ * Description: This command is used to query the version of the driver. Any
+ * driver version with major = 0, minor = 0, and update = 0 shall be considered
+ * an invalid or unknown version.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_drv_qver_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t reserved;
+ /* Reserved for future use */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being queried. 0xFF...
+ * (All Fs) if the query is for the requesting function.
+ */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_drv_qver_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t os_type;
+ /*
+ * This value indicates the type of OS. The values are based on
+ * CIM_OperatingSystem.mof file as published by the DMTF.
+ */
+ /* Unknown */
+ #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_UNKNOWN 0x0UL
+ /* Other OS not listed below. */
+ #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_OTHER 0x1UL
+ /* MSDOS OS. */
+ #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_MSDOS 0xeUL
+ /* Windows OS. */
+ #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_WINDOWS 0x12UL
+ /* Solaris OS. */
+ #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_SOLARIS 0x1dUL
+ /* Linux OS. */
+ #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_LINUX 0x24UL
+ /* FreeBSD OS. */
+ #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_FREEBSD 0x2aUL
+ /* VMware ESXi OS. */
+ #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_ESXI 0x68UL
+ /* Microsoft Windows 8 64-bit OS. */
+ #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_WIN864 0x73UL
+ /* Microsoft Windows Server 2012 R2 OS. */
+ #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_WIN2012R2 0x74UL
+ uint8_t ver_maj;
+ /* This is the major version of the driver. */
+ uint8_t ver_min;
+ /* This is the minor version of the driver. */
+ uint8_t ver_upd;
+ /* This is the update version of the driver. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_phy_cfg */
+/*
+ * Description: This command configures the PHY device for the port. It allows
+ * setting of the most generic settings for the PHY. The HWRM shall complete
+ * this command as soon as PHY settings are configured. They may not be applied
+ * when the command response is provided. A VF driver shall not be allowed to
+ * configure PHY using this command. In a network partition mode, a PF driver
+ * shall not be allowed to configure PHY using this command.
+ */
+/* Input (56 bytes) */
+struct hwrm_port_phy_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is set to '1', the PHY for the port shall be
+ * reset. # If this bit is set to 1, then the HWRM shall reset
+ * the PHY after applying PHY configuration changes specified in
+ * this command. # In order to guarantee that PHY configuration
+ * changes specified in this command take effect, the HWRM
+ * client should set this flag to 1. # If this bit is not set to
+ * 1, then the HWRM may reset the PHY depending on the current
+ * PHY configuration and settings specified in this command.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESET_PHY 0x1UL
+ /* deprecated bit. Do not use!!! */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_DEPRECATED 0x2UL
+ /*
+ * When this bit is set to '1', the link shall be forced to the
+ * force_link_speed value. When this bit is set to '1', the HWRM
+ * client should not enable any of the auto negotiation related
+ * fields represented by auto_XXX fields in this command. When
+ * this bit is set to '1' and the HWRM client has enabled a
+ * auto_XXX field in this command, then the HWRM shall ignore
+ * the enabled auto_XXX field. When this bit is set to zero, the
+ * link shall be allowed to autoneg.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE 0x4UL
+ /*
+ * When this bit is set to '1', the auto-negotiation process
+ * shall be restarted on the link.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG 0x8UL
+ /*
+ * When this bit is set to '1', Energy Efficient Ethernet (EEE)
+ * is requested to be enabled on this link. If EEE is not
+ * supported on this port, then this flag shall be ignored by
+ * the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_ENABLE 0x10UL
+ /*
+ * When this bit is set to '1', Energy Efficient Ethernet (EEE)
+ * is requested to be disabled on this link. If EEE is not
+ * supported on this port, then this flag shall be ignored by
+ * the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_DISABLE 0x20UL
+ /*
+ * When this bit is set to '1' and EEE is enabled on this link,
+ * then TX LPI is requested to be enabled on the link. If EEE is
+ * not supported on this port, then this flag shall be ignored
+ * by the HWRM. If EEE is disabled on this port, then this flag
+ * shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI_ENABLE 0x40UL
+ /*
+ * When this bit is set to '1' and EEE is enabled on this link,
+ * then TX LPI is requested to be disabled on the link. If EEE
+ * is not supported on this port, then this flag shall be
+ * ignored by the HWRM. If EEE is disabled on this port, then
+ * this flag shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI_DISABLE 0x80UL
+ /*
+ * When set to 1, then the HWRM shall enable FEC
+ * autonegotitation on this port if supported. When set to 0,
+ * then this flag shall be ignored. If FEC autonegotiation is
+ * not supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_AUTONEG_ENABLE 0x100UL
+ /*
+ * When set to 1, then the HWRM shall disable FEC
+ * autonegotiation on this port if supported. When set to 0,
+ * then this flag shall be ignored. If FEC autonegotiation is
+ * not supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_AUTONEG_DISABLE 0x200UL
+ /*
+ * When set to 1, then the HWRM shall enable FEC CLAUSE 74 (Fire
+ * Code) on this port if supported. When set to 0, then this
+ * flag shall be ignored. If FEC CLAUSE 74 is not supported,
+ * then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE74_ENABLE 0x400UL
+ /*
+ * When set to 1, then the HWRM shall disable FEC CLAUSE 74
+ * (Fire Code) on this port if supported. When set to 0, then
+ * this flag shall be ignored. If FEC CLAUSE 74 is not
+ * supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE74_DISABLE 0x800UL
+ /*
+ * When set to 1, then the HWRM shall enable FEC CLAUSE 91 (Reed
+ * Solomon) on this port if supported. When set to 0, then this
+ * flag shall be ignored. If FEC CLAUSE 91 is not supported,
+ * then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE91_ENABLE 0x1000UL
+ /*
+ * When set to 1, then the HWRM shall disable FEC CLAUSE 91
+ * (Reed Solomon) on this port if supported. When set to 0, then
+ * this flag shall be ignored. If FEC CLAUSE 91 is not
+ * supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE91_DISABLE 0x2000UL
+ /*
+ * When this bit is set to '1', the link shall be forced to be
+ * taken down. # When this bit is set to '1", all other command
+ * input settings related to the link speed shall be ignored.
+ * Once the link state is forced down, it can be explicitly
+ * cleared from that state by setting this flag to '0'. # If
+ * this flag is set to '0', then the link shall be cleared from
+ * forced down state if the link is in forced down state. There
+ * may be conditions (e.g. out-of-band or sideband configuration
+ * changes for the link) outside the scope of the HWRM
+ * implementation that may clear forced down link state.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE_LINK_DWN 0x4000UL
+ uint32_t enables;
+ /* This bit must be '1' for the auto_mode field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_MODE 0x1UL
+ /* This bit must be '1' for the auto_duplex field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_DUPLEX 0x2UL
+ /* This bit must be '1' for the auto_pause field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_PAUSE 0x4UL
+ /*
+ * This bit must be '1' for the auto_link_speed field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED 0x8UL
+ /*
+ * This bit must be '1' for the auto_link_speed_mask field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED_MASK 0x10UL
+ /* This bit must be '1' for the wirespeed field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_WIOUTPUTEED 0x20UL
+ /* This bit must be '1' for the lpbk field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_LPBK 0x40UL
+ /* This bit must be '1' for the preemphasis field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_PREEMPHASIS 0x80UL
+ /* This bit must be '1' for the force_pause field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_FORCE_PAUSE 0x100UL
+ /*
+ * This bit must be '1' for the eee_link_speed_mask field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_EEE_LINK_SPEED_MASK 0x200UL
+ /* This bit must be '1' for the tx_lpi_timer field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_TX_LPI_TIMER 0x400UL
+ uint16_t port_id;
+ /* Port ID of port that is to be configured. */
+ uint16_t force_link_speed;
+ /*
+ * This is the speed that will be used if the force bit is '1'.
+ * If unsupported speed is selected, an error will be generated.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100MB 0x1UL
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_1GB 0xaUL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2GB 0x14UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2_5GB 0x19UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10GB 0x64UL
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_20GB 0xc8UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_25GB 0xfaUL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_40GB 0x190UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_50GB 0x1f4UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100GB 0x3e8UL
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10MB 0xffffUL
+ uint8_t auto_mode;
+ /*
+ * This value is used to identify what autoneg mode is used when
+ * the link speed is not being forced.
+ */
+ /*
+ * Disable autoneg or autoneg disabled. No
+ * speeds are selected.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_NONE 0x0UL
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ALL_SPEEDS 0x1UL
+ /*
+ * Select only the auto_link_speed speed for
+ * autoneg mode. This mode has been DEPRECATED.
+ * An HWRM client should not use this mode.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_SPEED 0x2UL
+ /*
+ * Select the auto_link_speed or any speed below
+ * that speed for autoneg. This mode has been
+ * DEPRECATED. An HWRM client should not use
+ * this mode.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_OR_BELOW 0x3UL
+ /*
+ * Select the speeds based on the corresponding
+ * link speed mask value that is provided.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_SPEED_MASK 0x4UL
+ uint8_t auto_duplex;
+ /*
+ * This is the duplex setting that will be used if the
+ * autoneg_mode is "one_speed" or "one_or_below".
+ */
+ /* Half Duplex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_HALF 0x0UL
+ /* Full duplex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_FULL 0x1UL
+ /* Both Half and Full dupex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH 0x2UL
+ uint8_t auto_pause;
+ /*
+ * This value is used to configure the pause that will be used
+ * for autonegotiation. Add text on the usage of auto_pause and
+ * force_pause.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages has
+ * been requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_TX 0x1UL
+ /*
+ * When this bit is '1', Reception of rx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_RX 0x2UL
+ /*
+ * When set to 1, the advertisement of pause is enabled. # When
+ * the auto_mode is not set to none and this flag is set to 1,
+ * then the auto_pause bits on this port are being advertised
+ * and autoneg pause results are being interpreted. # When the
+ * auto_mode is not set to none and this flag is set to 0, the
+ * pause is forced as indicated in force_pause, and also
+ * advertised as auto_pause bits, but the autoneg results are
+ * not interpreted since the pause configuration is being
+ * forced. # When the auto_mode is set to none and this flag is
+ * set to 1, auto_pause bits should be ignored and should be set
+ * to 0.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_AUTONEG_PAUSE 0x4UL
+ uint8_t unused_0;
+ uint16_t auto_link_speed;
+ /*
+ * This is the speed that will be used if the autoneg_mode is
+ * "one_speed" or "one_or_below". If an unsupported speed is
+ * selected, an error will be generated.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100MB 0x1UL
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_1GB 0xaUL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2GB 0x14UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2_5GB 0x19UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10GB 0x64UL
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_20GB 0xc8UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_25GB 0xfaUL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_40GB 0x190UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_50GB 0x1f4UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100GB 0x3e8UL
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10MB 0xffffUL
+ uint16_t auto_link_speed_mask;
+ /*
+ * This is a mask of link speeds that will be used if
+ * autoneg_mode is "mask". If unsupported speed is enabled an
+ * error will be generated.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MBHD 0x1UL
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MB 0x2UL
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GBHD 0x4UL
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GB 0x8UL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2GB 0x10UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2_5GB 0x20UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10GB 0x40UL
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_20GB 0x80UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_25GB 0x100UL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_40GB 0x200UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_50GB 0x400UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100GB 0x800UL
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MBHD 0x1000UL
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MB 0x2000UL
+ uint8_t wirespeed;
+ /* This value controls the wirespeed feature. */
+ /* Wirespeed feature is disabled. */
+ #define HWRM_PORT_PHY_CFG_INPUT_WIOUTPUTEED_OFF 0x0UL
+ /* Wirespeed feature is enabled. */
+ #define HWRM_PORT_PHY_CFG_INPUT_WIOUTPUTEED_ON 0x1UL
+ uint8_t lpbk;
+ /* This value controls the loopback setting for the PHY. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_NONE 0x0UL
+ /*
+ * The HW will be configured with local loopback
+ * such that host data is sent back to the host
+ * without modification.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_LOCAL 0x1UL
+ /*
+ * The HW will be configured with remote
+ * loopback such that port logic will send
+ * packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_REMOTE 0x2UL
+ uint8_t force_pause;
+ /*
+ * This value is used to configure the pause that will be used
+ * for force mode.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_TX 0x1UL
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_RX 0x2UL
+ uint8_t unused_1;
+ uint32_t preemphasis;
+ /*
+ * This value controls the pre-emphasis to be used for the link.
+ * Driver should not set this value (use enable.preemphasis = 0)
+ * unless driver is sure of setting. Normally HWRM FW will
+ * determine proper pre-emphasis.
+ */
+ uint16_t eee_link_speed_mask;
+ /*
+ * Setting for link speed mask that is used to advertise speeds
+ * during autonegotiation when EEE is enabled. This field is
+ * valid only when EEE is enabled. The speeds specified in this
+ * field shall be a subset of speeds specified in
+ * auto_link_speed_mask. If EEE is enabled,then at least one
+ * speed shall be provided in this mask.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD1 0x1UL
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_100MB 0x2UL
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD2 0x4UL
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_1GB 0x8UL
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD3 0x10UL
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD4 0x20UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_10GB 0x40UL
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint32_t tx_lpi_timer;
+ uint32_t unused_4;
+ /*
+ * Reuested setting of TX LPI timer in microseconds. This field
+ * is valid only when EEE is enabled and TX LPI is enabled.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_MASK 0xffffffUL
+ #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_SFT 0
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_phy_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_phy_qcfg */
+/* Description: This command queries the PHY configuration for the port. */
+/* Input (24 bytes) */
+struct hwrm_port_phy_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is to be queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (96 bytes) */
+struct hwrm_port_phy_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t link;
+ /* This value indicates the current link status. */
+ /* There is no link or cable detected. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_NO_LINK 0x0UL
+ /* There is no link, but a cable has been detected. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SIGNAL 0x1UL
+ /* There is a link. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_LINK 0x2UL
+ uint8_t unused_0;
+ uint16_t link_speed;
+ /* This value indicates the current link speed of the connection. */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100MB 0x1UL
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_1GB 0xaUL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2GB 0x14UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2_5GB 0x19UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10GB 0x64UL
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_20GB 0xc8UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_25GB 0xfaUL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_40GB 0x190UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_50GB 0x1f4UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100GB 0x3e8UL
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10MB 0xffffUL
+ uint8_t duplex_cfg;
+ /* This value is indicates the duplex of the current configuration. */
+ /* Half Duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_CFG_HALF 0x0UL
+ /* Full duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_CFG_FULL 0x1UL
+ uint8_t pause;
+ /*
+ * This value is used to indicate the current pause
+ * configuration. When autoneg is enabled, this value represents
+ * the autoneg results of pause configuration.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_TX 0x1UL
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_RX 0x2UL
+ uint16_t support_speeds;
+ /*
+ * The supported speeds for the port. This is a bit mask. For
+ * each speed that is supported, the corrresponding bit will be
+ * set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MBHD 0x1UL
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MB 0x2UL
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GBHD 0x4UL
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GB 0x8UL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2GB 0x10UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2_5GB 0x20UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10GB 0x40UL
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_20GB 0x80UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_25GB 0x100UL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_40GB 0x200UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_50GB 0x400UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100GB 0x800UL
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MBHD 0x1000UL
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MB 0x2000UL
+ uint16_t force_link_speed;
+ /*
+ * Current setting of forced link speed. When the link speed is
+ * not being forced, this value shall be set to 0.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100MB 0x1UL
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_1GB 0xaUL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2GB 0x14UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2_5GB 0x19UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10GB 0x64UL
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_20GB 0xc8UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_25GB 0xfaUL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_40GB 0x190UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_50GB 0x1f4UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100GB 0x3e8UL
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10MB 0xffffUL
+ uint8_t auto_mode;
+ /* Current setting of auto negotiation mode. */
+ /*
+ * Disable autoneg or autoneg disabled. No
+ * speeds are selected.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_NONE 0x0UL
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ALL_SPEEDS 0x1UL
+ /*
+ * Select only the auto_link_speed speed for
+ * autoneg mode. This mode has been DEPRECATED.
+ * An HWRM client should not use this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_SPEED 0x2UL
+ /*
+ * Select the auto_link_speed or any speed below
+ * that speed for autoneg. This mode has been
+ * DEPRECATED. An HWRM client should not use
+ * this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_OR_BELOW 0x3UL
+ /*
+ * Select the speeds based on the corresponding
+ * link speed mask value that is provided.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_SPEED_MASK 0x4UL
+ uint8_t auto_pause;
+ /*
+ * Current setting of pause autonegotiation. Move autoneg_pause
+ * flag here.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages has
+ * been requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_TX 0x1UL
+ /*
+ * When this bit is '1', Reception of rx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_RX 0x2UL
+ /*
+ * When set to 1, the advertisement of pause is enabled. # When
+ * the auto_mode is not set to none and this flag is set to 1,
+ * then the auto_pause bits on this port are being advertised
+ * and autoneg pause results are being interpreted. # When the
+ * auto_mode is not set to none and this flag is set to 0, the
+ * pause is forced as indicated in force_pause, and also
+ * advertised as auto_pause bits, but the autoneg results are
+ * not interpreted since the pause configuration is being
+ * forced. # When the auto_mode is set to none and this flag is
+ * set to 1, auto_pause bits should be ignored and should be set
+ * to 0.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_AUTONEG_PAUSE 0x4UL
+ uint16_t auto_link_speed;
+ /*
+ * Current setting for auto_link_speed. This field is only valid
+ * when auto_mode is set to "one_speed" or "one_or_below".
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100MB 0x1UL
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_1GB 0xaUL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2GB 0x14UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2_5GB 0x19UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10GB 0x64UL
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_20GB 0xc8UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_25GB 0xfaUL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_40GB 0x190UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_50GB 0x1f4UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100GB 0x3e8UL
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10MB 0xffffUL
+ uint16_t auto_link_speed_mask;
+ /*
+ * Current setting for auto_link_speed_mask that is used to
+ * advertise speeds during autonegotiation. This field is only
+ * valid when auto_mode is set to "mask". The speeds specified
+ * in this field shall be a subset of supported speeds on this
+ * port.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MBHD 0x1UL
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MB 0x2UL
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GBHD 0x4UL
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GB 0x8UL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2GB 0x10UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2_5GB 0x20UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10GB 0x40UL
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_20GB 0x80UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_25GB 0x100UL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_40GB 0x200UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_50GB 0x400UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100GB 0x800UL
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MBHD 0x1000UL
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MB 0x2000UL
+ uint8_t wirespeed;
+ /* Current setting for wirespeed. */
+ /* Wirespeed feature is disabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_WIOUTPUTEED_OFF 0x0UL
+ /* Wirespeed feature is enabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_WIOUTPUTEED_ON 0x1UL
+ uint8_t lpbk;
+ /* Current setting for loopback. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_NONE 0x0UL
+ /*
+ * The HW will be configured with local loopback
+ * such that host data is sent back to the host
+ * without modification.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_LOCAL 0x1UL
+ /*
+ * The HW will be configured with remote
+ * loopback such that port logic will send
+ * packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_REMOTE 0x2UL
+ uint8_t force_pause;
+ /*
+ * Current setting of forced pause. When the pause configuration
+ * is not being forced, then this value shall be set to 0.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_TX 0x1UL
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_RX 0x2UL
+ uint8_t module_status;
+ /*
+ * This value indicates the current status of the optics module
+ * on this port.
+ */
+ /* Module is inserted and accepted */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NONE 0x0UL
+ /* Module is rejected and transmit side Laser is disabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_DISABLETX 0x1UL
+ /* Module mismatch warning. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_WARNINGMSG 0x2UL
+ /* Module is rejected and powered down. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_PWRDOWN 0x3UL
+ /* Module is not inserted. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTINSERTED 0x4UL
+ /* Module status is not applicable. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTAPPLICABLE 0xffUL
+ uint32_t preemphasis;
+ /* Current setting for preemphasis. */
+ uint8_t phy_maj;
+ /* This field represents the major version of the PHY. */
+ uint8_t phy_min;
+ /* This field represents the minor version of the PHY. */
+ uint8_t phy_bld;
+ /* This field represents the build version of the PHY. */
+ uint8_t phy_type;
+ /* This value represents a PHY type. */
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_UNKNOWN 0x0UL
+ /* BASE-CR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASECR 0x1UL
+ /* BASE-KR4 (Deprecated) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR4 0x2UL
+ /* BASE-LR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASELR 0x3UL
+ /* BASE-SR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASESR 0x4UL
+ /* BASE-KR2 (Deprecated) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR2 0x5UL
+ /* BASE-KX */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKX 0x6UL
+ /* BASE-KR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR 0x7UL
+ /* BASE-T */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASET 0x8UL
+ /* EEE capable BASE-T */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASETE 0x9UL
+ /* SGMII connected external PHY */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_SGMIIEXTPHY 0xaUL
+ /* 25G_BASECR_CA_L */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_L 0xbUL
+ /* 25G_BASECR_CA_S */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_S 0xcUL
+ /* 25G_BASECR_CA_N */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_N 0xdUL
+ /* 25G_BASESR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASESR 0xeUL
+ /* 100G_BASECR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASECR4 0xfUL
+ /* 100G_BASESR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASESR4 0x10UL
+ /* 100G_BASELR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASELR4 0x11UL
+ /* 100G_BASEER4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASEER4 0x12UL
+ /* 100G_BASESR10 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASESR10 0x13UL
+ /* 40G_BASECR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASECR4 0x14UL
+ /* 40G_BASESR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASESR4 0x15UL
+ /* 40G_BASELR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASELR4 0x16UL
+ /* 40G_BASEER4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASEER4 0x17UL
+ /* 40G_ACTIVE_CABLE */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_ACTIVE_CABLE 0x18UL
+ /* 1G_baseT */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_1G_BASET 0x19UL
+ /* 1G_baseSX */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_1G_BASESX 0x1aUL
+ /* 1G_baseCX */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_1G_BASECX 0x1bUL
+ uint8_t media_type;
+ /* This value represents a media type. */
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_UNKNOWN 0x0UL
+ /* Twisted Pair */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_TP 0x1UL
+ /* Direct Attached Copper */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_DAC 0x2UL
+ /* Fiber */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_FIBRE 0x3UL
+ uint8_t xcvr_pkg_type;
+ /* This value represents a transceiver type. */
+ /* PHY and MAC are in the same package */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_INTERNAL 0x1UL
+ /* PHY and MAC are in different packages */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_EXTERNAL 0x2UL
+ uint8_t eee_config_phy_addr;
+ /*
+ * This field represents flags related to EEE configuration.
+ * These EEE configuration flags are valid only when the
+ * auto_mode is not set to none (in other words autonegotiation
+ * is enabled).
+ */
+ /* This field represents PHY address. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_MASK 0x1fUL
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_SFT 0
+ /*
+ * When set to 1, Energy Efficient Ethernet (EEE) mode is
+ * enabled. Speeds for autoneg with EEE mode enabled are based
+ * on eee_link_speed_mask.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ENABLED 0x20UL
+ /*
+ * This flag is valid only when eee_enabled is set to 1. # If
+ * eee_enabled is set to 0, then EEE mode is disabled and this
+ * flag shall be ignored. # If eee_enabled is set to 1 and this
+ * flag is set to 1, then Energy Efficient Ethernet (EEE) mode
+ * is enabled and in use. # If eee_enabled is set to 1 and this
+ * flag is set to 0, then Energy Efficient Ethernet (EEE) mode
+ * is enabled but is currently not in use.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ACTIVE 0x40UL
+ /*
+ * This flag is valid only when eee_enabled is set to 1. # If
+ * eee_enabled is set to 0, then EEE mode is disabled and this
+ * flag shall be ignored. # If eee_enabled is set to 1 and this
+ * flag is set to 1, then Energy Efficient Ethernet (EEE) mode
+ * is enabled and TX LPI is enabled. # If eee_enabled is set to
+ * 1 and this flag is set to 0, then Energy Efficient Ethernet
+ * (EEE) mode is enabled but TX LPI is disabled.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_TX_LPI 0x80UL
+ /*
+ * This field represents flags related to EEE configuration.
+ * These EEE configuration flags are valid only when the
+ * auto_mode is not set to none (in other words autonegotiation
+ * is enabled).
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_MASK 0xe0UL
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_SFT 5
+ uint8_t parallel_detect;
+ /* Reserved field, set to 0 */
+ /*
+ * When set to 1, the parallel detection is used to determine
+ * the speed of the link partner. Parallel detection is used
+ * when a autonegotiation capable device is connected to a link
+ * parter that is not capable of autonegotiation.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PARALLEL_DETECT 0x1UL
+ /* Reserved field, set to 0 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_MASK 0xfeUL
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_SFT 1
+ uint16_t link_partner_adv_speeds;
+ /*
+ * The advertised speeds for the port by the link partner. Each
+ * advertised speed will be set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MBHD 0x1UL
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MB 0x2UL
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GBHD 0x4UL
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GB 0x8UL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2GB 0x10UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2_5GB 0x20UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10GB 0x40UL
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_20GB 0x80UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_25GB 0x100UL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_40GB 0x200UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_50GB 0x400UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100GB 0x800UL
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MBHD 0x1000UL
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MB 0x2000UL
+ uint8_t link_partner_adv_auto_mode;
+ /*
+ * The advertised autoneg for the port by the link partner. This
+ * field is deprecated and should be set to 0.
+ */
+ /*
+ * Disable autoneg or autoneg disabled. No
+ * speeds are selected.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_NONE 0x0UL
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ALL_SPEEDS \
+ 0x1UL
+ /*
+ * Select only the auto_link_speed speed for
+ * autoneg mode. This mode has been DEPRECATED.
+ * An HWRM client should not use this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_SPEED \
+ 0x2UL
+ /*
+ * Select the auto_link_speed or any speed below
+ * that speed for autoneg. This mode has been
+ * DEPRECATED. An HWRM client should not use
+ * this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_OR_BELOW \
+ 0x3UL
+ /*
+ * Select the speeds based on the corresponding
+ * link speed mask value that is provided.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK \
+ 0x4UL
+ uint8_t link_partner_adv_pause;
+ /* The advertised pause settings on the port by the link partner. */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_TX 0x1UL
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_RX 0x2UL
+ uint16_t adv_eee_link_speed_mask;
+ /*
+ * Current setting for link speed mask that is used to advertise
+ * speeds during autonegotiation when EEE is enabled. This field
+ * is valid only when eee_enabled flags is set to 1. The speeds
+ * specified in this field shall be a subset of speeds specified
+ * in auto_link_speed_mask.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD1 0x1UL
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_100MB 0x2UL
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD2 0x4UL
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_1GB 0x8UL
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD3 0x10UL
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD4 0x20UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_10GB 0x40UL
+ uint16_t link_partner_adv_eee_link_speed_mask;
+ /*
+ * Current setting for link speed mask that is advertised by the
+ * link partner when EEE is enabled. This field is valid only
+ * when eee_enabled flags is set to 1.
+ */
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ 0x1UL
+ /* 100Mb link speed (Full-duplex) */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_100MB \
+ 0x2UL
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ 0x4UL
+ /* 1Gb link speed (Full-duplex) */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_1GB \
+ 0x8UL
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ 0x10UL
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ 0x20UL
+ /* 10Gb link speed */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_10GB \
+ 0x40UL
+ uint32_t xcvr_identifier_type_tx_lpi_timer;
+ /* This value represents transceiver identifier type. */
+ /*
+ * Current setting of TX LPI timer in microseconds. This field
+ * is valid only when_eee_enabled flag is set to 1 and
+ * tx_lpi_enabled is set to 1.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_MASK 0xffffffUL
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_SFT 0
+ /* This value represents transceiver identifier type. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_MASK 0xff000000UL
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFT 24
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_UNKNOWN \
+ (0x0UL << 24)
+ /* SFP/SFP+/SFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFP (0x3UL << 24)
+ /* QSFP */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP \
+ (0xcUL << 24)
+ /* QSFP+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFPPLUS \
+ (0xdUL << 24)
+ /* QSFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28 \
+ (0x11UL << 24)
+ uint16_t fec_cfg;
+ /*
+ * This value represents the current configuration of Forward
+ * Error Correction (FEC) on the port.
+ */
+ /*
+ * When set to 1, then FEC is not supported on this port. If
+ * this flag is set to 1, then all other FEC configuration flags
+ * shall be ignored. When set to 0, then FEC is supported as
+ * indicated by other configuration flags. If no cable is
+ * attached and the HWRM does not yet know the FEC capability,
+ * then the HWRM shall set this flag to 1 when reporting FEC
+ * capability.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_NONE_SUPPORTED 0x1UL
+ /*
+ * When set to 1, then FEC autonegotiation is supported on this
+ * port. When set to 0, then FEC autonegotiation is not
+ * supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_SUPPORTED 0x2UL
+ /*
+ * When set to 1, then FEC autonegotiation is enabled on this
+ * port. When set to 0, then FEC autonegotiation is disabled if
+ * supported. This flag should be ignored if FEC autonegotiation
+ * is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_ENABLED 0x4UL
+ /*
+ * When set to 1, then FEC CLAUSE 74 (Fire Code) is supported on
+ * this port. When set to 0, then FEC CLAUSE 74 (Fire Code) is
+ * not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_SUPPORTED 0x8UL
+ /*
+ * When set to 1, then FEC CLAUSE 74 (Fire Code) is enabled on
+ * this port. When set to 0, then FEC CLAUSE 74 (Fire Code) is
+ * disabled if supported. This flag should be ignored if FEC
+ * CLAUSE 74 is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_ENABLED 0x10UL
+ /*
+ * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is supported
+ * on this port. When set to 0, then FEC CLAUSE 91 (Reed
+ * Solomon) is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_SUPPORTED 0x20UL
+ /*
+ * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is enabled
+ * on this port. When set to 0, then FEC CLAUSE 91 (Reed
+ * Solomon) is disabled if supported. This flag should be
+ * ignored if FEC CLAUSE 91 is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_ENABLED 0x40UL
+ uint8_t duplex_state;
+ /*
+ * This value is indicates the duplex of the current connection
+ * state.
+ */
+ /* Half Duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_HALF 0x0UL
+ /* Full duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_FULL 0x1UL
+ uint8_t unused_1;
+ char phy_vendor_name[16];
+ /*
+ * Up to 16 bytes of null padded ASCII string representing PHY
+ * vendor. If the string is set to null, then the vendor name is
+ * not available.
+ */
+ char phy_vendor_partnumber[16];
+ /*
+ * Up to 16 bytes of null padded ASCII string that identifies
+ * vendor specific part number of the PHY. If the string is set
+ * to null, then the vendor specific part number is not
+ * available.
+ */
+ uint32_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_mac_cfg */
+/*
+ * Description: This command configures the MAC block for the port. # Only PF
+ * drivers shall be allowed to configure MAC. # A VF driver should not be
+ * allowed to configure MAC using this command. # In a network partition mode, a
+ * PF driver should not be allowed to configure MAC using this command. The QoS
+ * settings in port_mac_cfg() are global for all ports/functions. If multiple PF
+ * drivers on different ports are configuring QoS settings, then the HWRM is not
+ * responsible for maintaining consistency between them. A PF driver changing
+ * global QoS settings using this command may impact other PF drivers on
+ * different ports.
+ */
+/* Input (40 bytes) */
+struct hwrm_port_mac_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * In this field, there are a number of CoS mappings related
+ * flags that are used to configure CoS mappings and their
+ * corresponding priorities in the hardware. For the priorities
+ * of CoS mappings, the HWRM uses the following priority order
+ * (high to low) by default: # vlan pri # ip_dscp #
+ * tunnel_vlan_pri # default cos A subset of CoS mappings can be
+ * enabled. If a priority is not specified for an enabled CoS
+ * mapping, the priority will be assigned in the above order for
+ * the enabled CoS mappings. For example, if vlan_pri and
+ * ip_dscp CoS mappings are enabled and their priorities are not
+ * specified, the following priority order (high to low) will be
+ * used by the HWRM: # vlan_pri # ip_dscp # default cos vlan_pri
+ * CoS mapping together with default CoS with lower priority are
+ * enabled by default by the HWRM.
+ */
+ /*
+ * When this bit is '1', this command will configure the MAC to
+ * match the current link state of the PHY. If the link is not
+ * established on the PHY, then this bit has no effect.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_MATCH_LINK 0x1UL
+ /*
+ * When this bit is set to '1', the inner VLAN PRI to CoS
+ * mapping is requested to be enabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_VLAN_PRI2COS_ENABLE 0x2UL
+ /*
+ * When this bit is set to '1', tunnel VLAN PRI field to CoS
+ * mapping is requested to be enabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_TUNNEL_PRI2COS_ENABLE 0x4UL
+ /*
+ * When this bit is set to '1', the IP DSCP to CoS mapping is
+ * requested to be enabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_IP_DSCP2COS_ENABLE 0x8UL
+ /*
+ * When this bit is '1', the HWRM is requested to enable
+ * timestamp capture capability on the receive side of this
+ * port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_RX_TS_CAPTURE_ENABLE 0x10UL
+ /*
+ * When this bit is '1', the HWRM is requested to disable
+ * timestamp capture capability on the receive side of this
+ * port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_RX_TS_CAPTURE_DISABLE 0x20UL
+ /*
+ * When this bit is '1', the HWRM is requested to enable
+ * timestamp capture capability on the transmit side of this
+ * port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_TX_TS_CAPTURE_ENABLE 0x40UL
+ /*
+ * When this bit is '1', the HWRM is requested to disable
+ * timestamp capture capability on the transmit side of this
+ * port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_TX_TS_CAPTURE_DISABLE 0x80UL
+ /*
+ * When this bit is '1', the Out-Of-Box WoL is requested to be
+ * enabled on this port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_OOB_WOL_ENABLE 0x100UL
+ /*
+ * When this bit is '1', the the Out-Of-Box WoL is requested to
+ * be disabled on this port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_OOB_WOL_DISABLE 0x200UL
+ /*
+ * When this bit is set to '1', the inner VLAN PRI to CoS
+ * mapping is requested to be disabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_VLAN_PRI2COS_DISABLE 0x400UL
+ /*
+ * When this bit is set to '1', tunnel VLAN PRI field to CoS
+ * mapping is requested to be disabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_TUNNEL_PRI2COS_DISABLE 0x800UL
+ /*
+ * When this bit is set to '1', the IP DSCP to CoS mapping is
+ * requested to be disabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_IP_DSCP2COS_DISABLE 0x1000UL
+ uint32_t enables;
+ /* This bit must be '1' for the ipg field to be configured. */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_IPG 0x1UL
+ /* This bit must be '1' for the lpbk field to be configured. */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_LPBK 0x2UL
+ /*
+ * This bit must be '1' for the vlan_pri2cos_map_pri field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_VLAN_PRI2COS_MAP_PRI 0x4UL
+ /* This bit must be '1' for the Reserved1 field to be configured. */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_RESERVED1 0x8UL
+ /*
+ * This bit must be '1' for the tunnel_pri2cos_map_pri field to
+ * be configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_TUNNEL_PRI2COS_MAP_PRI 0x10UL
+ /*
+ * This bit must be '1' for the dscp2cos_map_pri field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_DSCP2COS_MAP_PRI 0x20UL
+ /*
+ * This bit must be '1' for the rx_ts_capture_ptp_msg_type field
+ * to be configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_RX_TS_CAPTURE_PTP_MSG_TYPE \
+ 0x40UL
+ /*
+ * This bit must be '1' for the tx_ts_capture_ptp_msg_type field
+ * to be configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_TX_TS_CAPTURE_PTP_MSG_TYPE \
+ 0x80UL
+ /*
+ * This bit must be '1' for the cos_field_cfg field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_COS_FIELD_CFG 0x100UL
+ uint16_t port_id;
+ /* Port ID of port that is to be configured. */
+ uint8_t ipg;
+ /*
+ * This value is used to configure the minimum IPG that will be
+ * sent between packets by this port.
+ */
+ uint8_t lpbk;
+ /* This value controls the loopback setting for the MAC. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_MAC_CFG_INPUT_LPBK_NONE 0x0UL
+ /*
+ * The HW will be configured with local loopback
+ * such that host data is sent back to the host
+ * without modification.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_LPBK_LOCAL 0x1UL
+ /*
+ * The HW will be configured with remote
+ * loopback such that port logic will send
+ * packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_LPBK_REMOTE 0x2UL
+ uint8_t vlan_pri2cos_map_pri;
+ /*
+ * This value controls the priority setting of VLAN PRI to CoS
+ * mapping based on VLAN Tags of inner packet headers of
+ * tunneled packets or packet headers of non-tunneled packets. #
+ * Each XXX_pri variable shall have a unique priority value when
+ * it is being specified. # When comparing priorities of
+ * mappings, higher value indicates higher priority. For
+ * example, a value of 0-3 is returned where 0 is being the
+ * lowest priority and 3 is being the highest priority.
+ */
+ uint8_t reserved1;
+ /* Reserved field */
+ uint8_t tunnel_pri2cos_map_pri;
+ /*
+ * This value controls the priority setting of VLAN PRI to CoS
+ * mapping based on VLAN Tags of tunneled header. This mapping
+ * only applies when tunneled headers are present. # Each
+ * XXX_pri variable shall have a unique priority value when it
+ * is being specified. # When comparing priorities of mappings,
+ * higher value indicates higher priority. For example, a value
+ * of 0-3 is returned where 0 is being the lowest priority and 3
+ * is being the highest priority.
+ */
+ uint8_t dscp2pri_map_pri;
+ /*
+ * This value controls the priority setting of IP DSCP to CoS
+ * mapping based on inner IP header of tunneled packets or IP
+ * header of non-tunneled packets. # Each XXX_pri variable shall
+ * have a unique priority value when it is being specified. #
+ * When comparing priorities of mappings, higher value indicates
+ * higher priority. For example, a value of 0-3 is returned
+ * where 0 is being the lowest priority and 3 is being the
+ * highest priority.
+ */
+ uint16_t rx_ts_capture_ptp_msg_type;
+ /*
+ * This is a 16-bit bit mask that is used to request a specific
+ * configuration of time stamp capture of PTP messages on the
+ * receive side of this port. This field shall be ignored if the
+ * ptp_rx_ts_capture_enable flag is not set in this command.
+ * Otherwise, if bit 'i' is set, then the HWRM is being
+ * requested to configure the receive side of the port to
+ * capture the time stamp of every received PTP message with
+ * messageType field value set to i.
+ */
+ uint16_t tx_ts_capture_ptp_msg_type;
+ /*
+ * This is a 16-bit bit mask that is used to request a specific
+ * configuration of time stamp capture of PTP messages on the
+ * transmit side of this port. This field shall be ignored if
+ * the ptp_tx_ts_capture_enable flag is not set in this command.
+ * Otherwise, if bit 'i' is set, then the HWRM is being
+ * requested to configure the transmit sied of the port to
+ * capture the time stamp of every transmitted PTP message with
+ * messageType field value set to i.
+ */
+ uint8_t cos_field_cfg;
+ /* Configuration of CoS fields. */
+ /* Reserved. */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_RSVD1 0x1UL
+ /*
+ * This field is used to specify selection of VLAN PRI value
+ * based on whether one or two VLAN Tags are present in the
+ * inner packet headers of tunneled packets or non-tunneled
+ * packets. This field is valid only if inner VLAN PRI to CoS
+ * mapping is enabled. If VLAN PRI to CoS mapping is not
+ * enabled, then this field shall be ignored.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_MASK 0x6UL
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_SFT 1
+ /*
+ * Select inner VLAN PRI when 1 or 2 VLAN Tags
+ * are present in the inner packet headers
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_INNERMOST \
+ (0x0UL << 1)
+ /*
+ * Select outer VLAN Tag PRI when 2 VLAN Tags
+ * are present in the inner packet headers. No
+ * VLAN PRI shall be selected for this
+ * configuration if only one VLAN Tag is present
+ * in the inner packet headers.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTER \
+ (0x1UL << 1)
+ /*
+ * Select outermost VLAN PRI when 1 or 2 VLAN
+ * Tags are present in the inner packet headers
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTERMOST \
+ (0x2UL << 1)
+ /* Unspecified */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED \
+ (0x3UL << 1)
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_LAST \
+ PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED
+ /*
+ * This field is used to specify selection of tunnel VLAN PRI
+ * value based on whether one or two VLAN Tags are present in
+ * tunnel headers. This field is valid only if tunnel VLAN PRI
+ * to CoS mapping is enabled. If tunnel VLAN PRI to CoS mapping
+ * is not enabled, then this field shall be ignored.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_MASK 0x18UL
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_SFT 3
+ /*
+ * Select inner VLAN PRI when 1 or 2 VLAN Tags
+ * are present in the tunnel packet headers
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_INNERMOST \
+ (0x0UL << 3)
+ /*
+ * Select outer VLAN Tag PRI when 2 VLAN Tags
+ * are present in the tunnel packet headers. No
+ * tunnel VLAN PRI shall be selected for this
+ * configuration if only one VLAN Tag is present
+ * in the tunnel packet headers.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTER \
+ (0x1UL << 3)
+ /*
+ * Select outermost VLAN PRI when 1 or 2 VLAN
+ * Tags are present in the tunnel packet headers
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTERMOST \
+ (0x2UL << 3)
+ /* Unspecified */
+ #define \
+ HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED \
+ (0x3UL << 3)
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_LAST \
+ PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED
+ /*
+ * This field shall be used to provide default CoS value that
+ * has been configured on this port. This field is valid only if
+ * default CoS mapping is enabled. If default CoS mapping is not
+ * enabled, then this field shall be ignored.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_DEFAULT_COS_MASK 0xe0UL
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_DEFAULT_COS_SFT 5
+ uint8_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_mac_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t mru;
+ /*
+ * This is the configured maximum length of Ethernet packet
+ * payload that is allowed to be received on the port. This
+ * value does not include the number of bytes used by Ethernet
+ * header and trailer (CRC).
+ */
+ uint16_t mtu;
+ /*
+ * This is the configured maximum length of Ethernet packet
+ * payload that is allowed to be transmitted on the port. This
+ * value does not include the number of bytes used by Ethernet
+ * header and trailer (CRC).
+ */
+ uint8_t ipg;
+ /* Current configuration of the IPG value. */
+ uint8_t lpbk;
+ /* Current value of the loopback value. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_NONE 0x0UL
+ /*
+ * The HW will be configured with local loopback
+ * such that host data is sent back to the host
+ * without modification.
+ */
+ #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_LOCAL 0x1UL
+ /*
+ * The HW will be configured with remote
+ * loopback such that port logic will send
+ * packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_REMOTE 0x2UL
+ uint8_t unused_0;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_mac_qcfg */
+/* Description: This command queries the MAC block for the port. */
+/* Input (24 bytes) */
+struct hwrm_port_mac_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is to be configured. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_port_mac_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t mru;
+ /*
+ * This is the configured maximum length of Ethernet packet
+ * payload that is allowed to be received on the port. This
+ * value does not include the number of bytes used by the
+ * Ethernet header and trailer (CRC).
+ */
+ uint16_t mtu;
+ /*
+ * This is the configured maximum length of Ethernet packet
+ * payload that is allowed to be transmitted on the port. This
+ * value does not include the number of bytes used by the
+ * Ethernet header and trailer (CRC).
+ */
+ uint8_t ipg;
+ /* The minimum IPG that will be sent between packets by this port. */
+ uint8_t lpbk;
+ /* The loopback setting for the MAC. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_NONE 0x0UL
+ /*
+ * The HW will be configured with local loopback
+ * such that host data is sent back to the host
+ * without modification.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_LOCAL 0x1UL
+ /*
+ * The HW will be configured with remote
+ * loopback such that port logic will send
+ * packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_REMOTE 0x2UL
+ uint8_t vlan_pri2cos_map_pri;
+ /*
+ * Priority setting for VLAN PRI to CoS mapping. # Each XXX_pri
+ * variable shall have a unique priority value when it is being
+ * used. # When comparing priorities of mappings, higher value
+ * indicates higher priority. For example, a value of 0-3 is
+ * returned where 0 is being the lowest priority and 3 is being
+ * the highest priority. # If the correspoding CoS mapping is
+ * not enabled, then this field should be ignored. # This value
+ * indicates the normalized priority value retained in the HWRM.
+ */
+ uint8_t flags;
+ /*
+ * In this field, a number of CoS mappings related flags are
+ * used to indicate configured CoS mappings.
+ */
+ /*
+ * When this bit is set to '1', the inner VLAN PRI to CoS
+ * mapping is enabled.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_VLAN_PRI2COS_ENABLE 0x1UL
+ /*
+ * When this bit is set to '1', tunnel VLAN PRI field to CoS
+ * mapping is enabled.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_TUNNEL_PRI2COS_ENABLE 0x2UL
+ /*
+ * When this bit is set to '1', the IP DSCP to CoS mapping is
+ * enabled.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_IP_DSCP2COS_ENABLE 0x4UL
+ /* When this bit is '1', the Out-Of-Box WoL is enabled on this port. */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_OOB_WOL_ENABLE 0x8UL
+ /* When this bit is '1', PTP is enabled for RX on this port. */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_PTP_RX_TS_CAPTURE_ENABLE 0x10UL
+ /* When this bit is '1', PTP is enabled for TX on this port. */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_PTP_TX_TS_CAPTURE_ENABLE 0x20UL
+ uint8_t tunnel_pri2cos_map_pri;
+ /*
+ * Priority setting for tunnel VLAN PRI to CoS mapping. # Each
+ * XXX_pri variable shall have a unique priority value when it
+ * is being used. # When comparing priorities of mappings,
+ * higher value indicates higher priority. For example, a value
+ * of 0-3 is returned where 0 is being the lowest priority and 3
+ * is being the highest priority. # If the correspoding CoS
+ * mapping is not enabled, then this field should be ignored. #
+ * This value indicates the normalized priority value retained
+ * in the HWRM.
+ */
+ uint8_t dscp2pri_map_pri;
+ /*
+ * Priority setting for DSCP to PRI mapping. # Each XXX_pri
+ * variable shall have a unique priority value when it is being
+ * used. # When comparing priorities of mappings, higher value
+ * indicates higher priority. For example, a value of 0-3 is
+ * returned where 0 is being the lowest priority and 3 is being
+ * the highest priority. # If the correspoding CoS mapping is
+ * not enabled, then this field should be ignored. # This value
+ * indicates the normalized priority value retained in the HWRM.
+ */
+ uint16_t rx_ts_capture_ptp_msg_type;
+ /*
+ * This is a 16-bit bit mask that represents the current
+ * configuration of time stamp capture of PTP messages on the
+ * receive side of this port. If bit 'i' is set, then the
+ * receive side of the port is configured to capture the time
+ * stamp of every received PTP message with messageType field
+ * value set to i. If all bits are set to 0 (i.e. field value
+ * set 0), then the receive side of the port is not configured
+ * to capture timestamp for PTP messages. If all bits are set to
+ * 1, then the receive side of the port is configured to capture
+ * timestamp for all PTP messages.
+ */
+ uint16_t tx_ts_capture_ptp_msg_type;
+ /*
+ * This is a 16-bit bit mask that represents the current
+ * configuration of time stamp capture of PTP messages on the
+ * transmit side of this port. If bit 'i' is set, then the
+ * transmit side of the port is configured to capture the time
+ * stamp of every received PTP message with messageType field
+ * value set to i. If all bits are set to 0 (i.e. field value
+ * set 0), then the transmit side of the port is not configured
+ * to capture timestamp for PTP messages. If all bits are set to
+ * 1, then the transmit side of the port is configured to
+ * capture timestamp for all PTP messages.
+ */
+ uint8_t cos_field_cfg;
+ /* Configuration of CoS fields. */
+ /* Reserved */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_RSVD 0x1UL
+ /*
+ * This field is used for selecting VLAN PRI value based on
+ * whether one or two VLAN Tags are present in the inner packet
+ * headers of tunneled packets or non-tunneled packets.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_MASK 0x6UL
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_SFT 1
+ /*
+ * Select inner VLAN PRI when 1 or 2 VLAN Tags
+ * are present in the inner packet headers
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_INNERMOST \
+ (0x0UL << 1)
+ /*
+ * Select outer VLAN Tag PRI when 2 VLAN Tags
+ * are present in the inner packet headers. No
+ * VLAN PRI is selected for this configuration
+ * if only one VLAN Tag is present in the inner
+ * packet headers.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTER \
+ (0x1UL << 1)
+ /*
+ * Select outermost VLAN PRI when 1 or 2 VLAN
+ * Tags are present in the inner packet headers
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTERMOST \
+ (0x2UL << 1)
+ /* Unspecified */
+ #define \
+ HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED \
+ (0x3UL << 1)
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_LAST \
+ PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED
+ /*
+ * This field is used for selecting tunnel VLAN PRI value based
+ * on whether one or two VLAN Tags are present in the tunnel
+ * headers of tunneled packets. This selection does not apply to
+ * non-tunneled packets.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_MASK \
+ 0x18UL
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_SFT 3
+ /*
+ * Select inner VLAN PRI when 1 or 2 VLAN Tags
+ * are present in the tunnel packet headers
+ */
+ #define \
+ HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_INNERMOST \
+ (0x0UL << 3)
+ /*
+ * Select outer VLAN Tag PRI when 2 VLAN Tags
+ * are present in the tunnel packet headers. No
+ * VLAN PRI is selected for this configuration
+ * if only one VLAN Tag is present in the tunnel
+ * packet headers.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTER \
+ (0x1UL << 3)
+ /*
+ * Select outermost VLAN PRI when 1 or 2 VLAN
+ * Tags are present in the tunnel packet headers
+ */
+ #define \
+ HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTERMOST \
+ (0x2UL << 3)
+ /* Unspecified */
+ #define \
+ HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED \
+ (0x3UL << 3)
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_LAST \
+ PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED
+ /*
+ * This field is used to provide default CoS value that has been
+ * configured on this port.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_DEFAULT_COS_MASK 0xe0UL
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_DEFAULT_COS_SFT 5
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_mac_ptp_qcfg */
+/* Description: This command queries the PTP information for the port. */
+/* Input (24 bytes) */
+struct hwrm_port_mac_ptp_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (80 bytes) */
+struct hwrm_port_mac_ptp_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t flags;
+ /*
+ * In this field, a number of PTP related flags are used to
+ * indicate configured PTP capabilities.
+ */
+ /*
+ * When this bit is set to '1', the PTP related registers are
+ * directly accessible by the host.
+ */
+ #define HWRM_PORT_MAC_PTP_QCFG_OUTPUT_FLAGS_DIRECT_ACCESS 0x1UL
+ /*
+ * When this bit is set to '1', the PTP information is
+ * accessible via HWRM commands.
+ */
+ #define HWRM_PORT_MAC_PTP_QCFG_OUTPUT_FLAGS_HWRM_ACCESS 0x2UL
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint32_t rx_ts_reg_off_lower;
+ /*
+ * Offset of the PTP register for the lower 32 bits of timestamp
+ * for RX.
+ */
+ uint32_t rx_ts_reg_off_upper;
+ /*
+ * Offset of the PTP register for the upper 32 bits of timestamp
+ * for RX.
+ */
+ uint32_t rx_ts_reg_off_seq_id;
+ /* Offset of the PTP register for the sequence ID for RX. */
+ uint32_t rx_ts_reg_off_src_id_0;
+ /* Offset of the first PTP source ID for RX. */
+ uint32_t rx_ts_reg_off_src_id_1;
+ /* Offset of the second PTP source ID for RX. */
+ uint32_t rx_ts_reg_off_src_id_2;
+ /* Offset of the third PTP source ID for RX. */
+ uint32_t rx_ts_reg_off_domain_id;
+ /* Offset of the domain ID for RX. */
+ uint32_t rx_ts_reg_off_fifo;
+ /* Offset of the PTP FIFO register for RX. */
+ uint32_t rx_ts_reg_off_fifo_adv;
+ /* Offset of the PTP advance FIFO register for RX. */
+ uint32_t rx_ts_reg_off_granularity;
+ /* PTP timestamp granularity for RX. */
+ uint32_t tx_ts_reg_off_lower;
+ /*
+ * Offset of the PTP register for the lower 32 bits of timestamp
+ * for TX.
+ */
+ uint32_t tx_ts_reg_off_upper;
+ /*
+ * Offset of the PTP register for the upper 32 bits of timestamp
+ * for TX.
+ */
+ uint32_t tx_ts_reg_off_seq_id;
+ /* Offset of the PTP register for the sequence ID for TX. */
+ uint32_t tx_ts_reg_off_fifo;
+ /* Offset of the PTP FIFO register for TX. */
+ uint32_t tx_ts_reg_off_granularity;
+ /* PTP timestamp granularity for TX. */
+ uint32_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_qstats */
+/* Description: This function returns per port Ethernet statistics. */
+/* Input (40 bytes) */
+struct hwrm_port_qstats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is being queried. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2[3];
+ uint8_t unused_3;
+ uint64_t tx_stat_host_addr;
+ /* This is the host address where Tx port statistics will be stored */
+ uint64_t rx_stat_host_addr;
+ /* This is the host address where Rx port statistics will be stored */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_qstats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t tx_stat_size;
+ /* The size of TX port statistics block in bytes. */
+ uint16_t rx_stat_size;
+ /* The size of RX port statistics block in bytes. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_lpbk_qstats */
+/* Description: This function returns loopback statistics. */
+/* Input (16 bytes) */
+struct hwrm_port_lpbk_qstats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+} __attribute__((packed));
+
+/* Output (96 bytes) */
+struct hwrm_port_lpbk_qstats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint64_t lpbk_ucast_frames;
+ /* Number of transmitted unicast frames */
+ uint64_t lpbk_mcast_frames;
+ /* Number of transmitted multicast frames */
+ uint64_t lpbk_bcast_frames;
+ /* Number of transmitted broadcast frames */
+ uint64_t lpbk_ucast_bytes;
+ /* Number of transmitted bytes for unicast traffic */
+ uint64_t lpbk_mcast_bytes;
+ /* Number of transmitted bytes for multicast traffic */
+ uint64_t lpbk_bcast_bytes;
+ /* Number of transmitted bytes for broadcast traffic */
+ uint64_t tx_stat_discard;
+ /* Total Tx Drops for loopback traffic reported by STATS block */
+ uint64_t tx_stat_error;
+ /* Total Tx Error Drops for loopback traffic reported by STATS block */
+ uint64_t rx_stat_discard;
+ /* Total Rx Drops for loopback traffic reported by STATS block */
+ uint64_t rx_stat_error;
+ /* Total Rx Error Drops for loopback traffic reported by STATS block */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_clr_stats */
+/*
+ * Description: This function clears per port statistics. The HWRM shall not
+ * allow a VF driver to clear port statistics. The HWRM shall not allow a PF
+ * driver to clear port statistics in a partitioning mode. The HWRM may allow a
+ * PF driver to clear port statistics in the non-partitioning mode.
+ */
+/* Input (24 bytes) */
+struct hwrm_port_clr_stats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_clr_stats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_lpbk_clr_stats */
+/*
+ * Description: This function clears loopback statistics. The HWRM shall not
+ * allow a VF driver to clear loopback statistics. The HWRM shall not allow a PF
+ * driver to clear loopback statistics in a partitioning mode. The HWRM may
+ * allow a PF driver to clear loopback statistics in the non-partitioning mode.
+ */
+/* Input (16 bytes) */
+struct hwrm_port_lpbk_clr_stats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_lpbk_clr_stats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_ts_query */
+/*
+ * Description: This function is used to read timestamp information captured for
+ * PTP messages on this port.
+ */
+/* Input (24 bytes) */
+struct hwrm_port_ts_query_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_PORT_TS_QUERY_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_PORT_TS_QUERY_INPUT_FLAGS_PATH_TX 0x0UL
+ /* rx path */
+ #define HWRM_PORT_TS_QUERY_INPUT_FLAGS_PATH_RX 0x1UL
+ #define HWRM_PORT_TS_QUERY_INPUT_FLAGS_PATH_LAST \
+ PORT_TS_QUERY_INPUT_FLAGS_PATH_RX
+ uint16_t port_id;
+ /* Port ID of port that is being queried. */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_port_ts_query_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint64_t ptp_msg_ts;
+ /* Timestamp value of PTP message captured. */
+ uint16_t ptp_msg_seqid;
+ /* Sequence ID of the PTP message captured. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_phy_qcaps */
+/*
+ * Description: This function is used to query the current capabilities of PHY
+ * on this link.
+ */
+/* Input (24 bytes) */
+struct hwrm_port_phy_qcaps_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_port_phy_qcaps_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t flags;
+ /* PHY capability flags */
+ /*
+ * If set to 1, then this field indicates that the link is
+ * capable of supporting EEE.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_EEE_SUPPORTED 0x1UL
+ /*
+ * Reserved field. The HWRM shall set this field to 0. An HWRM
+ * client shall ignore this field.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_RSVD1_MASK 0xfeUL
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_RSVD1_SFT 1
+ uint8_t port_cnt;
+ /* Number of front panel ports for this device. */
+ /* Not supported or unknown */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_UNKNOWN 0x0UL
+ /* single port device */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_1 0x1UL
+ /* 2-port device */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_2 0x2UL
+ /* 3-port device */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_3 0x3UL
+ /* 4-port device */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_4 0x4UL
+ uint16_t supported_speeds_force_mode;
+ /*
+ * This is a bit mask to indicate what speeds are supported as
+ * forced speeds on this link. For each speed that can be forced
+ * on this link, the corresponding mask bit shall be set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_100MBHD \
+ 0x1UL
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_100MB \
+ 0x2UL
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_1GBHD \
+ 0x4UL
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_1GB 0x8UL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_2GB \
+ 0x10UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_2_5GB \
+ 0x20UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_10GB 0x40UL
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_20GB \
+ 0x80UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_25GB \
+ 0x100UL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_40GB \
+ 0x200UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_50GB \
+ 0x400UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_100GB \
+ 0x800UL
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_10MBHD \
+ 0x1000UL
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_10MB \
+ 0x2000UL
+ uint16_t supported_speeds_auto_mode;
+ /*
+ * This is a bit mask to indicate what speeds are supported for
+ * autonegotiation on this link. For each speed that can be
+ * autonegotiated on this link, the corresponding mask bit shall
+ * be set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_100MBHD \
+ 0x1UL
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_100MB \
+ 0x2UL
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_1GBHD \
+ 0x4UL
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_1GB 0x8UL
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_2GB 0x10UL
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_2_5GB \
+ 0x20UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_10GB \
+ 0x40UL
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_20GB \
+ 0x80UL
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_25GB \
+ 0x100UL
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_40GB \
+ 0x200UL
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_50GB \
+ 0x400UL
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_100GB \
+ 0x800UL
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_10MBHD \
+ 0x1000UL
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_10MB \
+ 0x2000UL
+ uint16_t supported_speeds_eee_mode;
+ /*
+ * This is a bit mask to indicate what speeds are supported for
+ * EEE on this link. For each speed that can be autonegotiated
+ * when EEE is enabled on this link, the corresponding mask bit
+ * shall be set to '1'. This field is only valid when the
+ * eee_suppotred is set to '1'.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD1 \
+ 0x1UL
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_100MB 0x2UL
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD2 0x4UL
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_1GB 0x8UL
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD3 \
+ 0x10UL
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD4 \
+ 0x20UL
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_10GB 0x40UL
+ uint32_t tx_lpi_timer_low;
+ /*
+ * Reserved field. The HWRM shall set this field to 0. An HWRM
+ * client shall ignore this field.
+ */
+ /*
+ * The lowest value of TX LPI timer that can be set on this link
+ * when EEE is enabled. This value is in microseconds. This
+ * field is valid only when_eee_supported is set to '1'.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_LOW_MASK 0xffffffUL
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_LOW_SFT 0
+ /*
+ * Reserved field. The HWRM shall set this field to 0. An HWRM
+ * client shall ignore this field.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_RSVD2_MASK 0xff000000UL
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_RSVD2_SFT 24
+ uint32_t valid_tx_lpi_timer_high;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+ /*
+ * The highest value of TX LPI timer that can be set on this
+ * link when EEE is enabled. This value is in microseconds. This
+ * field is valid only when_eee_supported is set to '1'.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_HIGH_MASK 0xffffffUL
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_HIGH_SFT 0
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_VALID_MASK 0xff000000UL
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_VALID_SFT 24
+} __attribute__((packed));
+
+/* hwrm_port_phy_i2c_write */
+/* Note: Write data at a specific location addressable on PHY I2C bus. */
+/* Input (48 bytes) */
+struct hwrm_port_phy_i2c_write_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ uint32_t enables;
+ /* This bit must be '1' for the page_offset field to be configured. */
+ #define HWRM_PORT_PHY_I2C_WRITE_INPUT_ENABLES_PAGE_OFFSET 0x1UL
+ uint16_t port_id;
+ /* Port ID of port. */
+ uint8_t i2c_slave_addr;
+ /* 8-bit I2C slave address. */
+ uint8_t unused_0;
+ uint16_t page_number;
+ /* The page number that is being accessed over I2C. */
+ uint16_t page_offset;
+ /* Offset within the page that is being accessed over I2C. */
+ uint8_t data_length;
+ /*
+ * Length of data to write, in bytes starting at the offset
+ * specified above. If the offset is not specified, then the
+ * data shall be written from the beginning of the page.
+ */
+ uint8_t unused_1;
+ uint16_t unused_2;
+ uint16_t unused_3;
+ uint16_t unused_4;
+ uint32_t data[16];
+ /* Up to 64B of data. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_phy_i2c_write_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_phy_i2c_read */
+/* Note: Write data at a specific location addressable on PHY I2C bus. */
+/* Input (40 bytes) */
+struct hwrm_port_phy_i2c_read_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ uint32_t enables;
+ /* This bit must be '1' for the page_offset field to be configured. */
+ #define HWRM_PORT_PHY_I2C_READ_INPUT_ENABLES_PAGE_OFFSET 0x1UL
+ uint16_t port_id;
+ /* Port ID of port. */
+ uint8_t i2c_slave_addr;
+ /* 8-bit I2C slave address. */
+ uint8_t unused_0;
+ uint16_t page_number;
+ /* The page number that is being accessed over I2C. */
+ uint16_t page_offset;
+ /* Offset within the page that is being accessed over I2C. */
+ uint8_t data_length;
+ /*
+ * Length of data to read, in bytes starting at the offset
+ * specified above. If the offset is not specified, then the
+ * data shall be read from the beginning of the page.
+ */
+ uint8_t unused_1[7];
+} __attribute__((packed));
+
+/* Output (80 bytes) */
+struct hwrm_port_phy_i2c_read_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t data[16];
+ /* Up to 64B of data. */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_led_cfg */
+/*
+ * Description: This function is used to configure LEDs on a given port. Each
+ * port has individual set of LEDs associated with it. These LEDs are used for
+ * speed/link configuration as well as activity indicator configuration. Up to
+ * three LEDs can be configured, one for activity and two for speeds.
+ */
+/* Input (64 bytes) */
+struct hwrm_port_led_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the led0_id field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_ID 0x1UL
+ /* This bit must be '1' for the led0_state field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_STATE 0x2UL
+ /* This bit must be '1' for the led0_color field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_COLOR 0x4UL
+ /*
+ * This bit must be '1' for the led0_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_BLINK_ON 0x8UL
+ /*
+ * This bit must be '1' for the led0_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_BLINK_OFF 0x10UL
+ /*
+ * This bit must be '1' for the led0_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_GROUP_ID 0x20UL
+ /* This bit must be '1' for the led1_id field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_ID 0x40UL
+ /* This bit must be '1' for the led1_state field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_STATE 0x80UL
+ /* This bit must be '1' for the led1_color field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_COLOR 0x100UL
+ /*
+ * This bit must be '1' for the led1_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_BLINK_ON 0x200UL
+ /*
+ * This bit must be '1' for the led1_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_BLINK_OFF 0x400UL
+ /*
+ * This bit must be '1' for the led1_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_GROUP_ID 0x800UL
+ /* This bit must be '1' for the led2_id field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_ID 0x1000UL
+ /* This bit must be '1' for the led2_state field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_STATE 0x2000UL
+ /* This bit must be '1' for the led2_color field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_COLOR 0x4000UL
+ /*
+ * This bit must be '1' for the led2_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_BLINK_ON 0x8000UL
+ /*
+ * This bit must be '1' for the led2_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_BLINK_OFF 0x10000UL
+ /*
+ * This bit must be '1' for the led2_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_GROUP_ID 0x20000UL
+ /* This bit must be '1' for the led3_id field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_ID 0x40000UL
+ /* This bit must be '1' for the led3_state field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_STATE 0x80000UL
+ /* This bit must be '1' for the led3_color field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_COLOR 0x100000UL
+ /*
+ * This bit must be '1' for the led3_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_BLINK_ON 0x200000UL
+ /*
+ * This bit must be '1' for the led3_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_BLINK_OFF 0x400000UL
+ /*
+ * This bit must be '1' for the led3_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_GROUP_ID 0x800000UL
+ uint16_t port_id;
+ /* Port ID of port whose LEDs are configured. */
+ uint8_t num_leds;
+ /*
+ * The number of LEDs that are being configured. Up to 4 LEDs
+ * can be configured with this command.
+ */
+ uint8_t rsvd;
+ /* Reserved field. */
+ uint8_t led0_id;
+ /* An identifier for the LED #0. */
+ uint8_t led0_state;
+ /* The requested state of the LED #0. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_DEFAULT 0x0UL
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_OFF 0x1UL
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_ON 0x2UL
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINK 0x3UL
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINKALT 0x4UL
+ uint8_t led0_color;
+ /* The requested color of LED #0. */
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_DEFAULT 0x0UL
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_AMBER 0x1UL
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREEN 0x2UL
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREENAMBER 0x3UL
+ uint8_t unused_0;
+ uint16_t led0_blink_on;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led0_blink_off;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led0_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs to.
+ * If set to 0, then the LED #0 shall not be grouped and shall
+ * be treated as an individual resource. For all other non-zero
+ * values of this field, LED #0 shall be grouped together with
+ * the LEDs with the same group ID value.
+ */
+ uint8_t rsvd0;
+ /* Reserved field. */
+ uint8_t led1_id;
+ /* An identifier for the LED #1. */
+ uint8_t led1_state;
+ /* The requested state of the LED #1. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_DEFAULT 0x0UL
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_OFF 0x1UL
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_ON 0x2UL
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINK 0x3UL
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINKALT 0x4UL
+ uint8_t led1_color;
+ /* The requested color of LED #1. */
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_DEFAULT 0x0UL
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_AMBER 0x1UL
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREEN 0x2UL
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREENAMBER 0x3UL
+ uint8_t unused_1;
+ uint16_t led1_blink_on;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led1_blink_off;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led1_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #1 belongs to.
+ * If set to 0, then the LED #1 shall not be grouped and shall
+ * be treated as an individual resource. For all other non-zero
+ * values of this field, LED #1 shall be grouped together with
+ * the LEDs with the same group ID value.
+ */
+ uint8_t rsvd1;
+ /* Reserved field. */
+ uint8_t led2_id;
+ /* An identifier for the LED #2. */
+ uint8_t led2_state;
+ /* The requested state of the LED #2. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_DEFAULT 0x0UL
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_OFF 0x1UL
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_ON 0x2UL
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINK 0x3UL
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINKALT 0x4UL
+ uint8_t led2_color;
+ /* The requested color of LED #2. */
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_DEFAULT 0x0UL
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_AMBER 0x1UL
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREEN 0x2UL
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREENAMBER 0x3UL
+ uint8_t unused_2;
+ uint16_t led2_blink_on;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led2_blink_off;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led2_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #2 belongs to.
+ * If set to 0, then the LED #2 shall not be grouped and shall
+ * be treated as an individual resource. For all other non-zero
+ * values of this field, LED #2 shall be grouped together with
+ * the LEDs with the same group ID value.
+ */
+ uint8_t rsvd2;
+ /* Reserved field. */
+ uint8_t led3_id;
+ /* An identifier for the LED #3. */
+ uint8_t led3_state;
+ /* The requested state of the LED #3. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_DEFAULT 0x0UL
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_OFF 0x1UL
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_ON 0x2UL
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINK 0x3UL
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINKALT 0x4UL
+ uint8_t led3_color;
+ /* The requested color of LED #3. */
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_DEFAULT 0x0UL
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_AMBER 0x1UL
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREEN 0x2UL
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREENAMBER 0x3UL
+ uint8_t unused_3;
+ uint16_t led3_blink_on;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led3_blink_off;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led3_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #3 belongs to.
+ * If set to 0, then the LED #3 shall not be grouped and shall
+ * be treated as an individual resource. For all other non-zero
+ * values of this field, LED #3 shall be grouped together with
+ * the LEDs with the same group ID value.
+ */
+ uint8_t rsvd3;
+ /* Reserved field. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_led_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_led_qcfg */
+/*
+ * Description: This function is used to query configuration of LEDs on a given
+ * port. Each port has individual set of LEDs associated with it. These LEDs are
+ * used for speed/link configuration as well as activity indicator
+ * configuration. Up to three LEDs can be configured, one for activity and two
+ * for speeds.
+ */
+/* Input (24 bytes) */
+struct hwrm_port_led_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port whose LED configuration is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (56 bytes) */
+struct hwrm_port_led_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t num_leds;
+ /*
+ * The number of LEDs that are configured on this port. Up to 4
+ * LEDs can be returned in the response.
+ */
+ uint8_t led0_id;
+ /* An identifier for the LED #0. */
+ uint8_t led0_type;
+ /* The type of LED #0. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_SPEED 0x0UL
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_ACTIVITY 0x1UL
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_INVALID 0xffUL
+ uint8_t led0_state;
+ /* The current state of the LED #0. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_DEFAULT 0x0UL
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_OFF 0x1UL
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_ON 0x2UL
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINK 0x3UL
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINKALT 0x4UL
+ uint8_t led0_color;
+ /* The color of LED #0. */
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_DEFAULT 0x0UL
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_AMBER 0x1UL
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREEN 0x2UL
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREENAMBER 0x3UL
+ uint8_t unused_0;
+ uint16_t led0_blink_on;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led0_blink_off;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led0_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs to.
+ * If set to 0, then the LED #0 is not grouped. For all other
+ * non-zero values of this field, LED #0 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t led1_id;
+ /* An identifier for the LED #1. */
+ uint8_t led1_type;
+ /* The type of LED #1. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_SPEED 0x0UL
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_ACTIVITY 0x1UL
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_INVALID 0xffUL
+ uint8_t led1_state;
+ /* The current state of the LED #1. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_DEFAULT 0x0UL
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_OFF 0x1UL
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_ON 0x2UL
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINK 0x3UL
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINKALT 0x4UL
+ uint8_t led1_color;
+ /* The color of LED #1. */
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_DEFAULT 0x0UL
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_AMBER 0x1UL
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREEN 0x2UL
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREENAMBER 0x3UL
+ uint8_t unused_1;
+ uint16_t led1_blink_on;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led1_blink_off;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led1_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #1 belongs to.
+ * If set to 0, then the LED #1 is not grouped. For all other
+ * non-zero values of this field, LED #1 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t led2_id;
+ /* An identifier for the LED #2. */
+ uint8_t led2_type;
+ /* The type of LED #2. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_SPEED 0x0UL
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_ACTIVITY 0x1UL
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_INVALID 0xffUL
+ uint8_t led2_state;
+ /* The current state of the LED #2. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_DEFAULT 0x0UL
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_OFF 0x1UL
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_ON 0x2UL
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINK 0x3UL
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINKALT 0x4UL
+ uint8_t led2_color;
+ /* The color of LED #2. */
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_DEFAULT 0x0UL
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_AMBER 0x1UL
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREEN 0x2UL
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREENAMBER 0x3UL
+ uint8_t unused_2;
+ uint16_t led2_blink_on;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led2_blink_off;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led2_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #2 belongs to.
+ * If set to 0, then the LED #2 is not grouped. For all other
+ * non-zero values of this field, LED #2 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t led3_id;
+ /* An identifier for the LED #3. */
+ uint8_t led3_type;
+ /* The type of LED #3. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_SPEED 0x0UL
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_ACTIVITY 0x1UL
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_INVALID 0xffUL
+ uint8_t led3_state;
+ /* The current state of the LED #3. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_DEFAULT 0x0UL
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_OFF 0x1UL
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_ON 0x2UL
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINK 0x3UL
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINKALT 0x4UL
+ uint8_t led3_color;
+ /* The color of LED #3. */
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_DEFAULT 0x0UL
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_AMBER 0x1UL
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREEN 0x2UL
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREENAMBER 0x3UL
+ uint8_t unused_3;
+ uint16_t led3_blink_on;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led3_blink_off;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led3_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #3 belongs to.
+ * If set to 0, then the LED #3 is not grouped. For all other
+ * non-zero values of this field, LED #3 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t unused_4;
+ uint16_t unused_5;
+ uint8_t unused_6;
+ uint8_t unused_7;
+ uint8_t unused_8;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_led_qcaps */
+/*
+ * Description: This function is used to query capabilities of LEDs on a given
+ * port. Each port has individual set of LEDs associated with it. These LEDs are
+ * used for speed/link configuration as well as activity indicator
+ * configuration.
+ */
+/* Input (24 bytes) */
+struct hwrm_port_led_qcaps_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port whose LED configuration is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (48 bytes) */
+struct hwrm_port_led_qcaps_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t num_leds;
+ /*
+ * The number of LEDs that are configured on this port. Up to 4
+ * LEDs can be returned in the response.
+ */
+ uint8_t unused_0[3];
+ /* Reserved for future use. */
+ uint8_t led0_id;
+ /* An identifier for the LED #0. */
+ uint8_t led0_type;
+ /* The type of LED #0. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_SPEED 0x0UL
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_ACTIVITY 0x1UL
+ /* Invalid */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_INVALID 0xffUL
+ uint8_t led0_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs to.
+ * If set to 0, then the LED #0 cannot be grouped. For all other
+ * non-zero values of this field, LED #0 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t unused_1;
+ uint16_t led0_state_caps;
+ /* The states supported by LED #0. */
+ /*
+ * If set to 1, this LED is enabled. If set to 0, this LED is
+ * disabled.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_ENABLED 0x1UL
+ /*
+ * If set to 1, off state is supported on this LED. If set to 0,
+ * off state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_OFF_SUPPORTED 0x2UL
+ /*
+ * If set to 1, on state is supported on this LED. If set to 0,
+ * on state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_ON_SUPPORTED 0x4UL
+ /*
+ * If set to 1, blink state is supported on this LED. If set to
+ * 0, blink state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_BLINK_SUPPORTED 0x8UL
+ /*
+ * If set to 1, blink_alt state is supported on this LED. If set
+ * to 0, blink_alt state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_BLINK_ALT_SUPPORTED \
+ 0x10UL
+ uint16_t led0_color_caps;
+ /* The colors supported by LED #0. */
+ /* reserved */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_RSVD 0x1UL
+ /*
+ * If set to 1, Amber color is supported on this LED. If set to
+ * 0, Amber color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_AMBER_SUPPORTED 0x2UL
+ /*
+ * If set to 1, Green color is supported on this LED. If set to
+ * 0, Green color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_GREEN_SUPPORTED 0x4UL
+ uint8_t led1_id;
+ /* An identifier for the LED #1. */
+ uint8_t led1_type;
+ /* The type of LED #1. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_SPEED 0x0UL
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_ACTIVITY 0x1UL
+ /* Invalid */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_INVALID 0xffUL
+ uint8_t led1_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #1 belongs to.
+ * If set to 0, then the LED #0 cannot be grouped. For all other
+ * non-zero values of this field, LED #0 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t unused_2;
+ uint16_t led1_state_caps;
+ /* The states supported by LED #1. */
+ /*
+ * If set to 1, this LED is enabled. If set to 0, this LED is
+ * disabled.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_ENABLED 0x1UL
+ /*
+ * If set to 1, off state is supported on this LED. If set to 0,
+ * off state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_OFF_SUPPORTED 0x2UL
+ /*
+ * If set to 1, on state is supported on this LED. If set to 0,
+ * on state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_ON_SUPPORTED 0x4UL
+ /*
+ * If set to 1, blink state is supported on this LED. If set to
+ * 0, blink state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_BLINK_SUPPORTED 0x8UL
+ /*
+ * If set to 1, blink_alt state is supported on this LED. If set
+ * to 0, blink_alt state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_BLINK_ALT_SUPPORTED \
+ 0x10UL
+ uint16_t led1_color_caps;
+ /* The colors supported by LED #1. */
+ /* reserved */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_RSVD 0x1UL
+ /*
+ * If set to 1, Amber color is supported on this LED. If set to
+ * 0, Amber color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_AMBER_SUPPORTED 0x2UL
+ /*
+ * If set to 1, Green color is supported on this LED. If set to
+ * 0, Green color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_GREEN_SUPPORTED 0x4UL
+ uint8_t led2_id;
+ /* An identifier for the LED #2. */
+ uint8_t led2_type;
+ /* The type of LED #2. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_SPEED 0x0UL
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_ACTIVITY 0x1UL
+ /* Invalid */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_INVALID 0xffUL
+ uint8_t led2_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs to.
+ * If set to 0, then the LED #0 cannot be grouped. For all other
+ * non-zero values of this field, LED #0 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t unused_3;
+ uint16_t led2_state_caps;
+ /* The states supported by LED #2. */
+ /*
+ * If set to 1, this LED is enabled. If set to 0, this LED is
+ * disabled.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_ENABLED 0x1UL
+ /*
+ * If set to 1, off state is supported on this LED. If set to 0,
+ * off state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_OFF_SUPPORTED 0x2UL
+ /*
+ * If set to 1, on state is supported on this LED. If set to 0,
+ * on state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_ON_SUPPORTED 0x4UL
+ /*
+ * If set to 1, blink state is supported on this LED. If set to
+ * 0, blink state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_BLINK_SUPPORTED 0x8UL
+ /*
+ * If set to 1, blink_alt state is supported on this LED. If set
+ * to 0, blink_alt state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_BLINK_ALT_SUPPORTED \
+ 0x10UL
+ uint16_t led2_color_caps;
+ /* The colors supported by LED #2. */
+ /* reserved */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_RSVD 0x1UL
+ /*
+ * If set to 1, Amber color is supported on this LED. If set to
+ * 0, Amber color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_AMBER_SUPPORTED 0x2UL
+ /*
+ * If set to 1, Green color is supported on this LED. If set to
+ * 0, Green color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_GREEN_SUPPORTED 0x4UL
+ uint8_t led3_id;
+ /* An identifier for the LED #3. */
+ uint8_t led3_type;
+ /* The type of LED #3. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_SPEED 0x0UL
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_ACTIVITY 0x1UL
+ /* Invalid */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_INVALID 0xffUL
+ uint8_t led3_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #3 belongs to.
+ * If set to 0, then the LED #0 cannot be grouped. For all other
+ * non-zero values of this field, LED #0 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t unused_4;
+ uint16_t led3_state_caps;
+ /* The states supported by LED #3. */
+ /*
+ * If set to 1, this LED is enabled. If set to 0, this LED is
+ * disabled.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_ENABLED 0x1UL
+ /*
+ * If set to 1, off state is supported on this LED. If set to 0,
+ * off state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_OFF_SUPPORTED 0x2UL
+ /*
+ * If set to 1, on state is supported on this LED. If set to 0,
+ * on state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_ON_SUPPORTED 0x4UL
+ /*
+ * If set to 1, blink state is supported on this LED. If set to
+ * 0, blink state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_BLINK_SUPPORTED 0x8UL
+ /*
+ * If set to 1, blink_alt state is supported on this LED. If set
+ * to 0, blink_alt state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_BLINK_ALT_SUPPORTED \
+ 0x10UL
+ uint16_t led3_color_caps;
+ /* The colors supported by LED #3. */
+ /* reserved */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_RSVD 0x1UL
+ /*
+ * If set to 1, Amber color is supported on this LED. If set to
+ * 0, Amber color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_AMBER_SUPPORTED 0x2UL
+ /*
+ * If set to 1, Green color is supported on this LED. If set to
+ * 0, Green color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_GREEN_SUPPORTED 0x4UL
+ uint8_t unused_5;
+ uint8_t unused_6;
+ uint8_t unused_7;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_qportcfg */
+/*
+ * Description: This function is called by a driver to query queue configuration
+ * of a port. # The HWRM shall at least advertise one queue with lossy service
+ * profile. # The driver shall use this command to query queue ids before
+ * configuring or using any queues. # If a service profile is not set for a
+ * queue, then the driver shall not use that queue without configuring a service
+ * profile for it. # If the driver is not allowed to configure service profiles,
+ * then the driver shall only use queues for which service profiles are pre-
+ * configured.
+ */
+/* Input (24 bytes) */
+struct hwrm_queue_qportcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_TX 0x0UL
+ /* rx path */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX 0x1UL
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX
+ uint16_t port_id;
+ /*
+ * Port ID of port for which the queue configuration is being
+ * queried. This field is only required when sent by IPC.
+ */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (32 bytes) */
+struct hwrm_queue_qportcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t max_configurable_queues;
+ /*
+ * The maximum number of queues that can be configured on this
+ * port. Valid values range from 1 through 8.
+ */
+ uint8_t max_configurable_lossless_queues;
+ /*
+ * The maximum number of lossless queues that can be configured
+ * on this port. Valid values range from 0 through 8.
+ */
+ uint8_t queue_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_cfg command. Each bit represents a specific queue
+ * where bit 0 represents queue 0 and bit 7 represents queue 7.
+ * # A value of 0 indicates that the queue is not configurable
+ * by the hwrm_queue_cfg command. # A value of 1 indicates that
+ * the queue is configurable. # A hwrm_queue_cfg command shall
+ * return error when trying to configure a queue not
+ * configurable.
+ */
+ uint8_t queue_cfg_info;
+ /* Information about queue configuration. */
+ /*
+ * If this flag is set to '1', then the queues are configured
+ * asymmetrically on TX and RX sides. If this flag is set to
+ * '0', then the queues are configured symmetrically on TX and
+ * RX sides. For symmetric configuration, the queue
+ * configuration including queue ids and service profiles on the
+ * TX side is the same as the corresponding queue configuration
+ * on the RX side.
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG 0x1UL
+ uint8_t queue_pfcenable_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_pfcenable_cfg command. Each bit represents a
+ * specific priority where bit 0 represents priority 0 and bit 7
+ * represents priority 7. # A value of 0 indicates that the
+ * priority is not configurable by the hwrm_queue_pfcenable_cfg
+ * command. # A value of 1 indicates that the priority is
+ * configurable. # A hwrm_queue_pfcenable_cfg command shall
+ * return error when trying to configure a priority that is not
+ * configurable.
+ */
+ uint8_t queue_pri2cos_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_pri2cos_cfg command. Each bit represents a
+ * specific queue where bit 0 represents queue 0 and bit 7
+ * represents queue 7. # A value of 0 indicates that the queue
+ * is not configurable by the hwrm_queue_pri2cos_cfg command. #
+ * A value of 1 indicates that the queue is configurable. # A
+ * hwrm_queue_pri2cos_cfg command shall return error when trying
+ * to configure a queue that is not configurable.
+ */
+ uint8_t queue_cos2bw_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_pri2cos_cfg command. Each bit represents a
+ * specific queue where bit 0 represents queue 0 and bit 7
+ * represents queue 7. # A value of 0 indicates that the queue
+ * is not configurable by the hwrm_queue_pri2cos_cfg command. #
+ * A value of 1 indicates that the queue is configurable. # A
+ * hwrm_queue_pri2cos_cfg command shall return error when trying
+ * to configure a queue not configurable.
+ */
+ uint8_t queue_id0;
+ /*
+ * ID of CoS Queue 0. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id0_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSY 0x0UL
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSLESS \
+ 0x1UL
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_UNKNOWN \
+ 0xffUL
+ uint8_t queue_id1;
+ /*
+ * ID of CoS Queue 1. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id1_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSY 0x0UL
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSLESS \
+ 0x1UL
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_UNKNOWN \
+ 0xffUL
+ uint8_t queue_id2;
+ /*
+ * ID of CoS Queue 2. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id2_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSY 0x0UL
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSLESS \
+ 0x1UL
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_UNKNOWN \
+ 0xffUL
+ uint8_t queue_id3;
+ /*
+ * ID of CoS Queue 3. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id3_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSY 0x0UL
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS \
+ 0x1UL
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_UNKNOWN \
+ 0xffUL
+ uint8_t queue_id4;
+ /*
+ * ID of CoS Queue 4. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id4_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSY 0x0UL
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS \
+ 0x1UL
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_UNKNOWN \
+ 0xffUL
+ uint8_t queue_id5;
+ /*
+ * ID of CoS Queue 5. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id5_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSY 0x0UL
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS \
+ 0x1UL
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_UNKNOWN \
+ 0xffUL
+ uint8_t queue_id6;
+ /*
+ * ID of CoS Queue 6. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id6_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSY 0x0UL
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS \
+ 0x1UL
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_UNKNOWN \
+ 0xffUL
+ uint8_t queue_id7;
+ /*
+ * ID of CoS Queue 7. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id7_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSY 0x0UL
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS \
+ 0x1UL
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_UNKNOWN \
+ 0xffUL
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_qcfg */
+/*
+ * Description: This function is called by a driver to query a queue
+ * configuration.
+ */
+/* Input (24 bytes) */
+struct hwrm_queue_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_TX 0x0UL
+ /* rx path */
+ #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_RX 0x1UL
+ #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_LAST \
+ QUEUE_QCFG_INPUT_FLAGS_PATH_RX
+ uint32_t queue_id;
+ /* Queue ID of the queue. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_queue_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t queue_len;
+ /*
+ * This value is a the estimate packet length used in the TX
+ * arbiter.
+ */
+ uint8_t service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_LOSSY 0x0UL
+ /* Lossless */
+ #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_LOSSLESS 0x1UL
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_UNKNOWN 0xffUL
+ uint8_t queue_cfg_info;
+ /* Information about queue configuration. */
+ /*
+ * If this flag is set to '1', then the queue is configured
+ * asymmetrically on TX and RX sides. If this flag is set to
+ * '0', then this queue is configured symmetrically on TX and RX
+ * sides.
+ */
+ #define HWRM_QUEUE_QCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG 0x1UL
+ uint8_t unused_0;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_cfg */
+/* Description: This function is called by a driver to configure a queue. */
+/* Input (40 bytes) */
+struct hwrm_queue_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX, or both directions
+ * applicable to the resource. This enumeration is used for
+ * resources that are similar for both TX and RX paths of the
+ * chip.
+ */
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_MASK 0x3UL
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_SFT 0
+ /* tx path */
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_TX 0x0UL
+ /* rx path */
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_RX 0x1UL
+ /*
+ * Bi-directional (Symmetrically applicable to
+ * TX and RX paths)
+ */
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_BIDIR 0x2UL
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_LAST \
+ QUEUE_CFG_INPUT_FLAGS_PATH_BIDIR
+ uint32_t enables;
+ /* This bit must be '1' for the dflt_len field to be configured. */
+ #define HWRM_QUEUE_CFG_INPUT_ENABLES_DFLT_LEN 0x1UL
+ /*
+ * This bit must be '1' for the service_profile field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_CFG_INPUT_ENABLES_SERVICE_PROFILE 0x2UL
+ uint32_t queue_id;
+ /* Queue ID of queue that is to be configured by this function. */
+ uint32_t dflt_len;
+ /*
+ * This value is a the estimate packet length used in the TX
+ * arbiter. Set to 0xFF... (All Fs) to not adjust this value.
+ */
+ uint8_t service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_LOSSY 0x0UL
+ /* Lossless */
+ #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_LOSSLESS 0x1UL
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_UNKNOWN 0xffUL
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_queue_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_pfcenable_qcfg */
+/*
+ * Description: This function is called by a driver to query PFC configuration
+ * for different priorities on that port. This mapping can be different on
+ * different ports.
+ */
+/* Input (24 bytes) */
+struct hwrm_queue_pfcenable_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /*
+ * Port ID of port for which the table is being configured. The
+ * HWRM needs to check whether this function is allowed to
+ * configure pri2cos mapping on this port.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_queue_pfcenable_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t flags;
+ /* If set to 1, then PFC is enabled on PRI 0. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI0_PFC_ENABLED 0x1UL
+ /* If set to 1, then PFC is enabled on PRI 1. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI1_PFC_ENABLED 0x2UL
+ /* If set to 1, then PFC is enabled on PRI 2. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI2_PFC_ENABLED 0x4UL
+ /* If set to 1, then PFC is enabled on PRI 3. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI3_PFC_ENABLED 0x8UL
+ /* If set to 1, then PFC is enabled on PRI 4. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI4_PFC_ENABLED 0x10UL
+ /* If set to 1, then PFC is enabled on PRI 5. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI5_PFC_ENABLED 0x20UL
+ /* If set to 1, then PFC is enabled on PRI 6. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI6_PFC_ENABLED 0x40UL
+ /* If set to 1, then PFC is enabled on PRI 7. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI7_PFC_ENABLED 0x80UL
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_pfcenable_cfg */
+/*
+ * Description: This function is called by a driver to configure the PFC enabled
+ * for different priorities on that port. This mapping can be different on
+ * different ports.
+ */
+/* Input (24 bytes) */
+struct hwrm_queue_pfcenable_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /* If set to 1, then PFC is requested to be enabled on PRI 0. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI0_PFC_ENABLED 0x1UL
+ /* If set to 1, then PFC is requested to be enabled on PRI 1. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI1_PFC_ENABLED 0x2UL
+ /* If set to 1, then PFC is requested to be enabled on PRI 2. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI2_PFC_ENABLED 0x4UL
+ /* If set to 1, then PFC is requested to be enabled on PRI 3. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI3_PFC_ENABLED 0x8UL
+ /* If set to 1, then PFC is requested to be enabled on PRI 4. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI4_PFC_ENABLED 0x10UL
+ /* If set to 1, then PFC is requested to be enabled on PRI 5. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI5_PFC_ENABLED 0x20UL
+ /* If set to 1, then PFC is requested to be enabled on PRI 6. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI6_PFC_ENABLED 0x40UL
+ /* If set to 1, then PFC is requested to be enabled on PRI 7. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI7_PFC_ENABLED 0x80UL
+ uint16_t port_id;
+ /*
+ * Port ID of port for which the table is being configured. The
+ * HWRM needs to check whether this function is allowed to
+ * configure pri2cos mapping on this port.
+ */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_queue_pfcenable_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_pri2cos_qcfg */
+/*
+ * Description: This function is called by a driver to query configuration of
+ * the priority to CoS queue mapping on the transmit side and receive side. This
+ * mapping can be different in each direction (TX or RX). This mapping can be
+ * different on different ports. Each CoS queue represents a Traffic Class (TC)
+ * on that port.
+ */
+/* Input (24 bytes) */
+struct hwrm_queue_pri2cos_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_TX (0x0UL << 0)
+ /* rx path */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_RX (0x1UL << 0)
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_RX
+ /*
+ * When this bit is set to '0', the query is for VLAN PRI field
+ * in tunnel headers. When this bit is set to '1', the query is
+ * for VLAN PRI field in inner packet headers.
+ */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_IVLAN 0x2UL
+ uint8_t port_id;
+ /*
+ * Port ID of port for which the table is being configured. The
+ * HWRM needs to check whether this function is allowed to
+ * configure pri2cos mapping on this port.
+ */
+ uint8_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_queue_pri2cos_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t pri0_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 0. This value can only be
+ * changed before traffic has started. A value of 0xff indicates
+ * that no CoS queue is assigned to the specified priority.
+ */
+ uint8_t pri1_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 1. This value can only be
+ * changed before traffic has started. A value of 0xff indicates
+ * that no CoS queue is assigned to the specified priority.
+ */
+ uint8_t pri2_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 2 This value can only be
+ * changed before traffic has started. A value of 0xff indicates
+ * that no CoS queue is assigned to the specified priority.
+ */
+ uint8_t pri3_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 3. This value can only be
+ * changed before traffic has started. A value of 0xff indicates
+ * that no CoS queue is assigned to the specified priority.
+ */
+ uint8_t pri4_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 4. This value can only be
+ * changed before traffic has started. A value of 0xff indicates
+ * that no CoS queue is assigned to the specified priority.
+ */
+ uint8_t pri5_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 5. This value can only be
+ * changed before traffic has started. A value of 0xff indicates
+ * that no CoS queue is assigned to the specified priority.
+ */
+ uint8_t pri6_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 6. This value can only be
+ * changed before traffic has started. A value of 0xff indicates
+ * that no CoS queue is assigned to the specified priority.
+ */
+ uint8_t pri7_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 7. This value can only be
+ * changed before traffic has started. A value of 0xff indicates
+ * that no CoS queue is assigned to the specified priority.
+ */
+ uint8_t queue_cfg_info;
+ /* Information about queue configuration. */
+ /*
+ * If this flag is set to '1', then the PRI to CoS configuration
+ * is asymmetric on TX and RX sides. If this flag is set to '0',
+ * then PRI to CoS configuration is symmetric on TX and RX
+ * sides.
+ */
+ #define HWRM_QUEUE_PRI2COS_QCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG 0x1UL
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_pri2cos_cfg */
+/*
+ * Description: This function is called by a driver to configure the priority to
+ * CoS queue mapping on the transmit side and receive side. This mapping can be
+ * different in each direction (TX or RX). This mapping can be different on
+ * different ports. Each CoS queue represents a Traffic Class (TC) on that port.
+ * This command configures the VLAN PRI-to-TC mapping for a specific port in
+ * specific direction.
+ */
+/* Input (40 bytes) */
+struct hwrm_queue_pri2cos_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX, or both directions
+ * applicable to the resource. This enumeration is used for
+ * resources that are similar for both TX and RX paths of the
+ * chip.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_MASK 0x3UL
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_SFT 0
+ /* tx path */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_TX (0x0UL << 0)
+ /* rx path */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_RX (0x1UL << 0)
+ /*
+ * Bi-directional (Symmetrically applicable to
+ * TX and RX paths)
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_BIDIR (0x2UL << 0)
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_BIDIR
+ /*
+ * When this bit is set to '0', the mapping is requested for
+ * VLAN PRI field in tunnel headers. When this bit is set to
+ * '1', the mapping is requested for VLAN PRI field in inner
+ * packet headers.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_IVLAN 0x4UL
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the pri0_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI0_COS_QUEUE_ID 0x1UL
+ /*
+ * This bit must be '1' for the pri1_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI1_COS_QUEUE_ID 0x2UL
+ /*
+ * This bit must be '1' for the pri2_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI2_COS_QUEUE_ID 0x4UL
+ /*
+ * This bit must be '1' for the pri3_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI3_COS_QUEUE_ID 0x8UL
+ /*
+ * This bit must be '1' for the pri4_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI4_COS_QUEUE_ID 0x10UL
+ /*
+ * This bit must be '1' for the pri5_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI5_COS_QUEUE_ID 0x20UL
+ /*
+ * This bit must be '1' for the pri6_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI6_COS_QUEUE_ID 0x40UL
+ /*
+ * This bit must be '1' for the pri7_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI7_COS_QUEUE_ID 0x80UL
+ uint8_t port_id;
+ /*
+ * Port ID of port for which the table is being configured. The
+ * HWRM needs to check whether this function is allowed to
+ * configure pri2cos mapping on this port.
+ */
+ uint8_t pri0_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 0. This value can only be
+ * changed before traffic has started.
+ */
+ uint8_t pri1_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 1. This value can only be
+ * changed before traffic has started.
+ */
+ uint8_t pri2_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 2 This value can only be
+ * changed before traffic has started.
+ */
+ uint8_t pri3_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 3. This value can only be
+ * changed before traffic has started.
+ */
+ uint8_t pri4_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 4. This value can only be
+ * changed before traffic has started.
+ */
+ uint8_t pri5_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 5. This value can only be
+ * changed before traffic has started.
+ */
+ uint8_t pri6_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 6. This value can only be
+ * changed before traffic has started.
+ */
+ uint8_t pri7_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 7. This value can only be
+ * changed before traffic has started.
+ */
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_queue_pri2cos_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_cos2bw_qcfg */
+/*
+ * Description: This function is called by a driver to query the BW to CoS queue
+ * mapping on the transmit side of a specific port. This mapping can be
+ * different on different ports. Each CoS queue represents a Traffic Class (TC)
+ * on that port. Each traffic class can be assigned a valid combination of the
+ * following: - Minimum bandwidth - Maximum bandwidth - Transmission selection
+ * algorithm (TSA) - Priority Level (only applies to strict priority COS) -
+ * Bandwidth weight # A CoS can be SP or non-SP: A SP CoS always gets the strict
+ * priority. Is an COS min BW is set to 0x0 then it is considered to be non-SP;
+ * this is a valid configuration. Note: SP provides lower latency in addition to
+ * reserved bandwidth # For both SP CoS and non-SP CoS, min BW can be specified
+ * to reserve specific amount of the port BW. # The min BW specified for a CoS
+ * shall not exceed max port bandwidth. # The total of min BWs specified for all
+ * CoS shall not exceed max port bandwidth. # For any non-SP CoS, the minimum
+ * bandwidth guarantees are subject to round-robin scheduling. This allows BW
+ * reservation with anti-starvation; one CoS will not block another CoS using
+ * RR. Note: The bandwidth guarantees for any non-SP CoS are met after servicing
+ * all SP CoS. # An SP CoS can potentially starve other lower priority SP CoS
+ * and non-SP CoS queues. This can occur to the extent the SP min exceeds the
+ * available port BW. # For any CoS, max BW can be specified to limit the BW
+ * consumed by the CoS. # The max BW specified for a CoS shall not exceed the
+ * max port bandwidth. # The WFQ provides a mechanism for sharing available
+ * bandwidth beyond the reserved minimums configured for each CoS. The WFQ
+ * scheduler is used to provide the percentages of remaining bandwidth after: *
+ * first servicing the reserved bandwidth for all SP CoS, * followed by the
+ * reserved bandwidth for all non-SP CoS * All CoS may participate in the WFQ #
+ * If a CoS does not have a configured max BW it may use all available bandwidth
+ * up to the max port bandwidth Minimum Bandwidth (min BW): # This is the
+ * guaranteed bandwidth for the COS. # A value of 0x0 is valid and it means that
+ * this COS is not guaranteed any bandwidth. A value of 0xFF.. (all Fs) means
+ * min BW is not specified. When the min BW is not specified, the HWRM can set
+ * it to any value it considers appropriate. Note: For a non-SP COS, the HWRM
+ * should set min BW to 0 when the min BW is not specified. For an SP COS, the
+ * HWRM should set min BW to some small value when the min BW is not specified.
+ * Maximum Bandwidth: # This is the bandwidth limit of the COS. # Values 0x0 and
+ * 0xFF.. (all Fs) are considered unspecified and the HWRM will set the maximum
+ * bandwidth to maximum port bandwidth. Priority Level: # It applies only to SP.
+ * # This parameter is ignored for non-SP. # 0-7 are valid values (higher value
+ * means higher priority) # A priority level can be assigned to at most one SP.
+ * # Invalid priority levels assignment for SPs shall result in failure.
+ * Additional notes: # The HWRM may have to use min and (max - min) to set
+ * appropriate counters of hardware rate limiters. # The bandwidth percentage as
+ * specified in the DCB TC BW assignment should be used by the driver to specify
+ * maximum bandwidth and bandwidth weight for a COS. For example, the driver
+ * should set max BW to 20 Gbps and weight to 50 for two COSs when these two
+ * COSs are assigned 50% share of 40 Gbps max port bandwidth.
+ */
+/* Input (24 bytes) */
+struct hwrm_queue_cos2bw_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /*
+ * Port ID of port for which the table is being configured. The
+ * HWRM needs to check whether this function is allowed to
+ * configure TC BW assignment on this port.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (112 bytes) */
+struct hwrm_queue_cos2bw_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t queue_id0;
+ /* ID of CoS Queue 0. */
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint32_t queue_id0_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_LAST \
+ QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id0_max_bw;
+ /*
+ * Maximum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id0_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id0_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id0_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id1;
+ /* ID of CoS Queue 1. */
+ uint32_t queue_id1_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_LAST \
+ QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id1_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id1_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id1_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id1_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id2;
+ /* ID of CoS Queue 2. */
+ uint32_t queue_id2_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id2_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id2_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id2_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id2_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id3;
+ /* ID of CoS Queue 3. */
+ uint32_t queue_id3_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id3_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id3_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id3_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id3_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id4;
+ /* ID of CoS Queue 4. */
+ uint32_t queue_id4_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id4_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_LAST \
+ QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id4_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id4_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id4_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id5;
+ /* ID of CoS Queue 5. */
+ uint32_t queue_id5_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id5_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_LAST \
+ QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id5_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id5_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id5_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id6;
+ /* ID of CoS Queue 6. */
+ uint32_t queue_id6_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id6_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_LAST \
+ QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id6_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id6_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id6_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id7;
+ /* ID of CoS Queue 7. */
+ uint32_t queue_id7_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id7_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id7_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id7_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id7_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_cos2bw_cfg */
+/*
+ * Description: This function is called by a driver to configure the BW to CoS
+ * queue mapping on the transmit side of a specific port. This mapping can be
+ * different on different ports. Each CoS queue represents a Traffic Class (TC)
+ * on that port. Each traffic class can be assigned a valid combination of the
+ * following: - Minimum bandwidth - Maximum bandwidth - Transmission selection
+ * algorithm (TSA) - Priority Level (only applies to strict priority COS) -
+ * Bandwidth weight # A CoS can be SP or non-SP: A SP CoS always gets the strict
+ * priority. Note: SP provides lower latency in addition to reserved bandwidth #
+ * For non-SP CoS, min BW can be specified to reserve specific amount of the
+ * port BW. # The min BW specified for a CoS shall not exceed max port
+ * bandwidth. # The total of min BWs specified for all CoS shall not exceed max
+ * port bandwidth. # For any non-SP CoS, the minimum bandwidth guarantees are
+ * subject to round-robin scheduling. This allows BW reservation with anti-
+ * starvation; one CoS will not block another CoS using RR. Note: The bandwidth
+ * guarantees for any non-SP CoS are met after servicing all SP CoS. # An SP CoS
+ * can potentially starve other lower priority SP CoS and non-SP CoS queues.
+ * This can occur to the extent the SP min exceeds the available port BW. # For
+ * any CoS, max BW can be specified to limit the BW consumed by the CoS. # A max
+ * BW can be used for a SP CoS to limit the starvation of other CoS, but using
+ * this will cause some characteristics of any ETS CoS to be violated. # The max
+ * BW specified for a CoS shall not exceed the max port bandwidth. # For SP CoS,
+ * it is recommended to set min and max BW to 0. This instructs the adapter to
+ * use default values. # The WFQ provides a mechanism for sharing available
+ * bandwidth beyond the reserved minimums configured for each CoS. The WFQ
+ * scheduler is used to provide the percentages of remaining bandwidth after: -
+ * first servicing the reserved bandwidth for all SP CoS, - followed by the
+ * reserved bandwidth for all non-SP CoS - All CoS may participate in the WFQ #
+ * If a CoS does not have a configured max BW it may use all available bandwidth
+ * up to the max port bandwidth Minimum Bandwidth (min BW): # This is the
+ * guaranteed bandwidth for the COS. # A value of 0x0 is valid and it means that
+ * this COS is not guaranteed any bandwidth. A value of 0xFF.. (all Fs) means
+ * min BW is not specified. When the min BW is not specified, the HWRM can set
+ * it to any value it considers appropriate. Note: For a non-SP COS, the HWRM
+ * should set min BW to 0 when the min BW is not specified. For an SP COS, min
+ * BW value is ignored. Maximum Bandwidth: # This is the bandwidth limit of the
+ * COS. # Values 0x0 and 0xFF.. (all Fs) are considered unspecified and the HWRM
+ * will set the maximum bandwidth to maximum port bandwidth. Priority Level: #
+ * It applies only to SP. # This parameter is ignored for non-SP. # 0-7 are
+ * valid values (higher value means higher priority) # A priority level can be
+ * assigned to at most one SP. # Invalid priority levels assignment for SPs
+ * shall result in failure. Additional notes: # The HWRM may have to use min and
+ * (max - min) to set appropriate counters of hardware rate limiters. # The
+ * bandwidth percentage as specified in the DCB TC BW assignment should be used
+ * by the driver to specify minimum bandwidth and bandwidth weight for a COS.
+ * For example, the driver should set max BW to 20 Gbps and weight to 50 for two
+ * COSs when these two COSs are assigned 50% share of 40 Gbps max port
+ * bandwidth. DCBX use cases should always use max BW of 100% for all ETS CoS
+ * queues.
+ */
+/* Input (128 bytes) */
+struct hwrm_queue_cos2bw_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ uint32_t enables;
+ /*
+ * If this bit is set to 1, then all queue_id0 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID0_VALID 0x1UL
+ /*
+ * If this bit is set to 1, then all queue_id1 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID1_VALID 0x2UL
+ /*
+ * If this bit is set to 1, then all queue_id2 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID2_VALID 0x4UL
+ /*
+ * If this bit is set to 1, then all queue_id3 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID3_VALID 0x8UL
+ /*
+ * If this bit is set to 1, then all queue_id4 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID4_VALID 0x10UL
+ /*
+ * If this bit is set to 1, then all queue_id5 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID5_VALID 0x20UL
+ /*
+ * If this bit is set to 1, then all queue_id6 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID6_VALID 0x40UL
+ /*
+ * If this bit is set to 1, then all queue_id7 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID7_VALID 0x80UL
+ uint16_t port_id;
+ /*
+ * Port ID of port for which the table is being configured. The
+ * HWRM needs to check whether this function is allowed to
+ * configure TC BW assignment on this port.
+ */
+ uint8_t queue_id0;
+ /* ID of CoS Queue 0. */
+ uint8_t unused_0;
+ uint32_t queue_id0_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id0_max_bw;
+ /*
+ * Maximum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id0_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id0_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id0_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id1;
+ /* ID of CoS Queue 1. */
+ uint32_t queue_id1_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id1_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id1_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_FIRST 0x2UL
+ /* reserved */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id1_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id1_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id2;
+ /* ID of CoS Queue 2. */
+ uint32_t queue_id2_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_LAST \
+ QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id2_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_LAST \
+ QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id2_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id2_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id2_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id3;
+ /* ID of CoS Queue 3. */
+ uint32_t queue_id3_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id3_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id3_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id3_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id3_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id4;
+ /* ID of CoS Queue 4. */
+ uint32_t queue_id4_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id4_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_LAST \
+ QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id4_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id4_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id4_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id5;
+ /* ID of CoS Queue 5. */
+ uint32_t queue_id5_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_LAST \
+ QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id5_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_LAST \
+ QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id5_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id5_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id5_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id6;
+ /* ID of CoS Queue 6. */
+ uint32_t queue_id6_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_LAST \
+ QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id6_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_LAST \
+ QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id6_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id6_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id6_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id7;
+ /* ID of CoS Queue 7. */
+ uint32_t queue_id7_min_bw;
+ /*
+ * Minimum BW allocated to CoS Queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_LAST \
+ QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t queue_id7_max_bw;
+ /*
+ * Maximum BW allocated to CoS queue. The HWRM will translate
+ * this value into byte counter and time interval used for this
+ * COS inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_LAST \
+ QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t queue_id7_tsa_assign;
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_SP 0x0UL
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_ETS 0x1UL
+ /* reserved */
+ #define \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_FIRST \
+ 0x2UL
+ /* reserved */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_LAST \
+ 0xffUL
+ uint8_t queue_id7_pri_lvl;
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP) 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id7_bw_weight;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t unused_1[5];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_queue_cos2bw_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_dscp_qcaps */
+/*
+ * Description: This command is called by a driver to query the DSCP
+ * capabilities for a port.
+ */
+/* Input (24 bytes) */
+struct hwrm_queue_dscp_qcaps_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint8_t port_id;
+ /*
+ * Port ID of port for which the table is being configured. The
+ * HWRM needs to check whether this function is allowed to
+ * configure pri2cos mapping on this port.
+ */
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_queue_dscp_qcaps_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t num_dscp_bits;
+ /* The number of bits provided by the hardware for the DSCP value. */
+ uint8_t unused_0;
+ uint16_t max_entries;
+ /* Max number of DSCP-MASK-PRI entries supported. */
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_dscp2pri_qcfg */
+/*
+ * Description: This command is called by a driver to query configuration of the
+ * DSCP to PRI mapping on the receive side. This mapping can be different on
+ * different ports.
+ */
+/* Input (32 bytes) */
+struct hwrm_queue_dscp2pri_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint64_t dest_data_addr;
+ /*
+ * This is the host address where the 24-bits DSCP-MASK-PRI
+ * tuple(s) will be copied to.
+ */
+ uint8_t port_id;
+ /*
+ * Port ID of port for which the table is being configured. The
+ * HWRM needs to check whether this function is allowed to
+ * configure pri2cos mapping on this port.
+ */
+ uint8_t unused_0;
+ uint16_t dest_data_buffer_size;
+ /* Size of the buffer pointed to by dest_data_addr. */
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_queue_dscp2pri_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t entry_cnt;
+ /*
+ * A count of the number of DSCP-MASK-PRI tuple(s) pointed to by
+ * the dest_data_addr.
+ */
+ uint8_t default_pri;
+ /*
+ * This is the default PRI which un-initialized DSCP values are
+ * mapped to.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_dscp2pri_cfg */
+/*
+ * Description: This command is called by a driver to configure the DSCP to PRI
+ * mapping on the receive side. This mapping can be different on different
+ * ports.
+ */
+/* Input (40 bytes) */
+struct hwrm_queue_dscp2pri_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint64_t src_data_addr;
+ /*
+ * This is the host address where the 24-bits DSCP-MASK-PRI
+ * tuple will be copied from.
+ */
+ uint32_t flags;
+ /* use_hw_default_pri is 1 b */
+ #define HWRM_QUEUE_DSCP2PRI_CFG_INPUT_FLAGS_USE_HW_DEFAULT_PRI 0x1UL
+ uint32_t enables;
+ /* This bit must be '1' for the default_pri field to be configured. */
+ #define HWRM_QUEUE_DSCP2PRI_CFG_INPUT_ENABLES_DEFAULT_PRI 0x1UL
+ uint8_t port_id;
+ /*
+ * Port ID of port for which the table is being configured. The
+ * HWRM needs to check whether this function is allowed to
+ * configure pri2cos mapping on this port.
+ */
+ uint8_t default_pri;
+ /*
+ * This is the default PRI which un-initialized DSCP values will
+ * be mapped to.
+ */
+ uint16_t entry_cnt;
+ /*
+ * A count of the number of DSCP-MASK-PRI tuple(s) in the data
+ * pointed to by src_data_addr.
+ */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_queue_dscp2pri_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_alloc */
+/*
+ * Description: This VNIC is a resource in the RX side of the chip that is used
+ * to represent a virtual host "interface". # At the time of VNIC allocation or
+ * configuration, the function can specify whether it wants the requested VNIC
+ * to be the default VNIC for the function or not. # If a function requests
+ * allocation of a VNIC for the first time and a VNIC is successfully allocated
+ * by the HWRM, then the HWRM shall make the allocated VNIC as the default VNIC
+ * for that function. # The default VNIC shall be used for the default action
+ * for a partition or function. # For each VNIC allocated on a function, a
+ * mapping on the RX side to map the allocated VNIC to source virtual interface
+ * shall be performed by the HWRM. This should be hidden to the function driver
+ * requesting the VNIC allocation. This enables broadcast/multicast replication
+ * with source knockout. # If multicast replication with source knockout is
+ * enabled, then the internal VNIC to SVIF mapping data structures shall be
+ * programmed at the time of VNIC allocation.
+ */
+/* Input (24 bytes) */
+struct hwrm_vnic_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', this VNIC is requested to be the
+ * default VNIC for this function.
+ */
+ #define HWRM_VNIC_ALLOC_INPUT_FLAGS_DEFAULT 0x1UL
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_free */
+/*
+ * Description: Free a VNIC resource. Idle any resources associated with the
+ * VNIC as well as the VNIC. Reset and release all resources associated with the
+ * VNIC.
+ */
+/* Input (24 bytes) */
+struct hwrm_vnic_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_cfg */
+/* Description: Configure the RX VNIC structure. */
+/* Input (40 bytes) */
+struct hwrm_vnic_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is requested to be the default
+ * VNIC for the function.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_DEFAULT 0x1UL
+ /*
+ * When this bit is '1', the VNIC is being configured to strip
+ * VLAN in the RX path. If set to '0', then VLAN stripping is
+ * disabled on this VNIC.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_VLAN_STRIP_MODE 0x2UL
+ /*
+ * When this bit is '1', the VNIC is being configured to buffer
+ * receive packets in the hardware until the host posts new
+ * receive buffers. If set to '0', then bd_stall is being
+ * configured to be disabled on this VNIC.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_BD_STALL_MODE 0x4UL
+ /*
+ * When this bit is '1', the VNIC is being configured to receive
+ * both RoCE and non-RoCE traffic. If set to '0', then this VNIC
+ * is not configured to be operating in dual VNIC mode.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_DUAL_VNIC_MODE 0x8UL
+ /*
+ * When this flag is set to '1', the VNIC is requested to be
+ * configured to receive only RoCE traffic. If this flag is set
+ * to '0', then this flag shall be ignored by the HWRM. If
+ * roce_dual_vnic_mode flag is set to '1' or
+ * roce_mirroring_capable_vnic_mode flag to 1, then the HWRM
+ * client shall not set this flag to '1'.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_ONLY_VNIC_MODE 0x10UL
+ /*
+ * When a VNIC uses one destination ring group for certain
+ * application (e.g. Receive Flow Steering) where exact match is
+ * used to direct packets to a VNIC with one destination ring
+ * group only, there is no need to configure RSS indirection
+ * table for that VNIC as only one destination ring group is
+ * used. This flag is used to enable a mode where RSS is enabled
+ * in the VNIC using a RSS context for computing RSS hash but
+ * the RSS indirection table is not configured using
+ * hwrm_vnic_rss_cfg. If this mode is enabled, then the driver
+ * should not program RSS indirection table for the RSS context
+ * that is used for computing RSS hash only.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_RSS_DFLT_CR_MODE 0x20UL
+ /*
+ * When this bit is '1', the VNIC is being configured to receive
+ * both RoCE and non-RoCE traffic, but forward only the RoCE
+ * traffic further. Also, RoCE traffic can be mirrored to L2
+ * driver.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_MIRRORING_CAPABLE_VNIC_MODE 0x40UL
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the dflt_ring_grp field to be
+ * configured.
+ */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_DFLT_RING_GRP 0x1UL
+ /* This bit must be '1' for the rss_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_RSS_RULE 0x2UL
+ /* This bit must be '1' for the cos_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_COS_RULE 0x4UL
+ /* This bit must be '1' for the lb_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_LB_RULE 0x8UL
+ /* This bit must be '1' for the mru field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_MRU 0x10UL
+ uint16_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t dflt_ring_grp;
+ /*
+ * Default Completion ring for the VNIC. This ring will be
+ * chosen if packet does not match any RSS rules and if there is
+ * no COS rule.
+ */
+ uint16_t rss_rule;
+ /*
+ * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if
+ * there is no RSS rule.
+ */
+ uint16_t cos_rule;
+ /*
+ * RSS ID for COS rule/table structure. 0xFF... (All Fs) if
+ * there is no COS rule.
+ */
+ uint16_t lb_rule;
+ /*
+ * RSS ID for load balancing rule/table structure. 0xFF... (All
+ * Fs) if there is no LB rule.
+ */
+ uint16_t mru;
+ /*
+ * The maximum receive unit of the vnic. Each vnic is associated
+ * with a function. The vnic mru value overwrites the mru
+ * setting of the associated function. The HWRM shall make sure
+ * that vnic mru does not exceed the mru of the port the
+ * function is associated with.
+ */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_qcfg */
+/*
+ * Description: Query the RX VNIC structure. This function can be used by a PF
+ * driver to query its own VNIC resource or VNIC resource of its child VF. This
+ * function can also be used by a VF driver to query its own VNIC resource.
+ */
+/* Input (32 bytes) */
+struct hwrm_vnic_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id_valid field to be configured. */
+ #define HWRM_VNIC_QCFG_INPUT_ENABLES_VF_ID_VALID 0x1UL
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t vf_id;
+ /* ID of Virtual Function whose VNIC resource is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (32 bytes) */
+struct hwrm_vnic_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t dflt_ring_grp;
+ /* Default Completion ring for the VNIC. */
+ uint16_t rss_rule;
+ /*
+ * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if
+ * there is no RSS rule.
+ */
+ uint16_t cos_rule;
+ /*
+ * RSS ID for COS rule/table structure. 0xFF... (All Fs) if
+ * there is no COS rule.
+ */
+ uint16_t lb_rule;
+ /*
+ * RSS ID for load balancing rule/table structure. 0xFF... (All
+ * Fs) if there is no LB rule.
+ */
+ uint16_t mru;
+ /* The maximum receive unit of the vnic. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is the default VNIC for the
+ * function.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_DEFAULT 0x1UL
+ /*
+ * When this bit is '1', the VNIC is configured to strip VLAN in
+ * the RX path. If set to '0', then VLAN stripping is disabled
+ * on this VNIC.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_VLAN_STRIP_MODE 0x2UL
+ /*
+ * When this bit is '1', the VNIC is configured to buffer
+ * receive packets in the hardware until the host posts new
+ * receive buffers. If set to '0', then bd_stall is disabled on
+ * this VNIC.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_BD_STALL_MODE 0x4UL
+ /*
+ * When this bit is '1', the VNIC is configured to receive both
+ * RoCE and non-RoCE traffic. If set to '0', then this VNIC is
+ * not configured to operate in dual VNIC mode.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_DUAL_VNIC_MODE 0x8UL
+ /*
+ * When this flag is set to '1', the VNIC is configured to
+ * receive only RoCE traffic. When this flag is set to '0', the
+ * VNIC is not configured to receive only RoCE traffic. If
+ * roce_dual_vnic_mode flag and this flag both are set to '1',
+ * then it is an invalid configuration of the VNIC. The HWRM
+ * should not allow that type of mis-configuration by HWRM
+ * clients.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_ONLY_VNIC_MODE 0x10UL
+ /*
+ * When a VNIC uses one destination ring group for certain
+ * application (e.g. Receive Flow Steering) where exact match is
+ * used to direct packets to a VNIC with one destination ring
+ * group only, there is no need to configure RSS indirection
+ * table for that VNIC as only one destination ring group is
+ * used. When this bit is set to '1', then the VNIC is enabled
+ * in a mode where RSS is enabled in the VNIC using a RSS
+ * context for computing RSS hash but the RSS indirection table
+ * is not configured.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_RSS_DFLT_CR_MODE 0x20UL
+ /*
+ * When this bit is '1', the VNIC is configured to receive both
+ * RoCE and non-RoCE traffic, but forward only RoCE traffic
+ * further. Also RoCE traffic can be mirrored to L2 driver.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_MIRRORING_CAPABLE_VNIC_MODE 0x40UL
+ uint32_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_qcaps */
+/*
+ * Description: This function is used to query the capabilities of VNIC
+ * resources.
+ */
+/* Input (24 bytes) */
+struct hwrm_vnic_qcaps_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_vnic_qcaps_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t mru;
+ /* The maximum receive unit that is settable on a vnic. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t flags;
+ /* Unused. */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_UNUSED 0x1UL
+ /*
+ * When this bit is '1', the capability of stripping VLAN in the
+ * RX path is supported on VNIC(s). If set to '0', then VLAN
+ * stripping capability is not supported on VNIC(s).
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_VLAN_STRIP_CAP 0x2UL
+ /*
+ * When this bit is '1', the capability to buffer receive
+ * packets in the hardware until the host posts new receive
+ * buffers is supported on VNIC(s). If set to '0', then bd_stall
+ * capability is not supported on VNIC(s).
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_BD_STALL_CAP 0x4UL
+ /*
+ * When this bit is '1', the capability to receive both RoCE and
+ * non-RoCE traffic on VNIC(s) is supported. If set to '0', then
+ * the capability to receive both RoCE and non-RoCE traffic on
+ * VNIC(s) is not supported.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_ROCE_DUAL_VNIC_CAP 0x8UL
+ /*
+ * When this bit is set to '1', the capability to configure a
+ * VNIC to receive only RoCE traffic is supported. When this
+ * flag is set to '0', the VNIC capability to configure to
+ * receive only RoCE traffic is not supported.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_ROCE_ONLY_VNIC_CAP 0x10UL
+ /*
+ * When this bit is set to '1', then the capability to enable a
+ * VNIC in a mode where RSS context without configuring RSS
+ * indirection table is supported (for RSS hash computation).
+ * When this bit is set to '0', then a VNIC can not be
+ * configured with a mode to enable RSS context without
+ * configuring RSS indirection table.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_RSS_DFLT_CR_CAP 0x20UL
+ /*
+ * When this bit is '1', the capability to mirror the the RoCE
+ * traffic is supported. If set to '0', then the capability to
+ * mirror the RoCE traffic is not supported.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_ROCE_MIRROING_CAPABLE_VNIC_CAP 0x40UL
+ uint32_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_tpa_cfg */
+/* Description: This function is used to enable/configure TPA on the VNIC. */
+/* Input (40 bytes) */
+struct hwrm_vnic_tpa_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) of non-tunneled TCP
+ * packets.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_TPA 0x1UL
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) of tunneled TCP packets.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_ENCAP_TPA 0x2UL
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) according to Windows
+ * Receive Segment Coalescing (RSC) rules.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_RSC_WND_UPDATE 0x4UL
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) according to Linux
+ * Generic Receive Offload (GRO) rules.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO 0x8UL
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) for TCP packets with IP
+ * ECN set to non-zero.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_WITH_ECN 0x10UL
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) for GRE tunneled TCP
+ * packets only if all packets have the same GRE sequence.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_WITH_SAME_GRE_SEQ 0x20UL
+ /*
+ * When this bit is '1' and the GRO mode is enabled, the VNIC
+ * shall be configured to perform transparent packet aggregation
+ * (TPA) for TCP/IPv4 packets with consecutively increasing
+ * IPIDs. In other words, the last packet that is being
+ * aggregated to an already existing aggregation context shall
+ * have IPID 1 more than the IPID of the last packet that was
+ * aggregated in that aggregation context.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO_IPID_CHECK 0x40UL
+ /*
+ * When this bit is '1' and the GRO mode is enabled, the VNIC
+ * shall be configured to perform transparent packet aggregation
+ * (TPA) for TCP packets with the same TTL (IPv4) or Hop limit
+ * (IPv6) value.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO_TTL_CHECK 0x80UL
+ uint32_t enables;
+ /* This bit must be '1' for the max_agg_segs field to be configured. */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGG_SEGS 0x1UL
+ /* This bit must be '1' for the max_aggs field to be configured. */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGGS 0x2UL
+ /*
+ * This bit must be '1' for the max_agg_timer field to be
+ * configured.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGG_TIMER 0x4UL
+ /* This bit must be '1' for the min_agg_len field to be configured. */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MIN_AGG_LEN 0x8UL
+ uint16_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t max_agg_segs;
+ /*
+ * This is the maximum number of TCP segments that can be
+ * aggregated (unit is Log2). Max value is 31.
+ */
+ /* 1 segment */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_1 0x0UL
+ /* 2 segments */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_2 0x1UL
+ /* 4 segments */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_4 0x2UL
+ /* 8 segments */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_8 0x3UL
+ /* Any segment size larger than this is not valid */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_MAX 0x1fUL
+ uint16_t max_aggs;
+ /*
+ * This is the maximum number of aggregations this VNIC is
+ * allowed (unit is Log2). Max value is 7
+ */
+ /* 1 aggregation */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_1 0x0UL
+ /* 2 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_2 0x1UL
+ /* 4 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_4 0x2UL
+ /* 8 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_8 0x3UL
+ /* 16 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_16 0x4UL
+ /* Any aggregation size larger than this is not valid */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_MAX 0x7UL
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t max_agg_timer;
+ /*
+ * This is the maximum amount of time allowed for an aggregation
+ * context to complete after it was initiated.
+ */
+ uint32_t min_agg_len;
+ /*
+ * This is the minimum amount of payload length required to
+ * start an aggregation context.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_tpa_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_tpa_qcfg */
+/*
+ * Description: This function can be used to query TPA configuration on the
+ * VNIC.
+ */
+/* Input (24 bytes) */
+struct hwrm_vnic_tpa_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (32 bytes) */
+struct hwrm_vnic_tpa_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is configured to perform
+ * transparent packet aggregation (TPA) of non-tunneled TCP
+ * packets.
+ */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_TPA 0x1UL
+ /*
+ * When this bit is '1', the VNIC is configured to perform
+ * transparent packet aggregation (TPA) of tunneled TCP packets.
+ */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_ENCAP_TPA 0x2UL
+ /*
+ * When this bit is '1', the VNIC is configured to perform
+ * transparent packet aggregation (TPA) according to Windows
+ * Receive Segment Coalescing (RSC) rules.
+ */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_RSC_WND_UPDATE 0x4UL
+ /*
+ * When this bit is '1', the VNIC is configured to perform
+ * transparent packet aggregation (TPA) according to Linux
+ * Generic Receive Offload (GRO) rules.
+ */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_GRO 0x8UL
+ /*
+ * When this bit is '1', the VNIC is configured to perform
+ * transparent packet aggregation (TPA) for TCP packets with IP
+ * ECN set to non-zero.
+ */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_AGG_WITH_ECN 0x10UL
+ /*
+ * When this bit is '1', the VNIC is configured to perform
+ * transparent packet aggregation (TPA) for GRE tunneled TCP
+ * packets only if all packets have the same GRE sequence.
+ */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_AGG_WITH_SAME_GRE_SEQ 0x20UL
+ /*
+ * When this bit is '1' and the GRO mode is enabled, the VNIC is
+ * configured to perform transparent packet aggregation (TPA)
+ * for TCP/IPv4 packets with consecutively increasing IPIDs. In
+ * other words, the last packet that is being aggregated to an
+ * already existing aggregation context shall have IPID 1 more
+ * than the IPID of the last packet that was aggregated in that
+ * aggregation context.
+ */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_GRO_IPID_CHECK 0x40UL
+ /*
+ * When this bit is '1' and the GRO mode is enabled, the VNIC is
+ * configured to perform transparent packet aggregation (TPA)
+ * for TCP packets with the same TTL (IPv4) or Hop limit (IPv6)
+ * value.
+ */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_GRO_TTL_CHECK 0x80UL
+ uint16_t max_agg_segs;
+ /*
+ * This is the maximum number of TCP segments that can be
+ * aggregated (unit is Log2). Max value is 31.
+ */
+ /* 1 segment */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_1 0x0UL
+ /* 2 segments */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_2 0x1UL
+ /* 4 segments */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_4 0x2UL
+ /* 8 segments */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_8 0x3UL
+ /* Any segment size larger than this is not valid */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_MAX 0x1fUL
+ uint16_t max_aggs;
+ /*
+ * This is the maximum number of aggregations this VNIC is
+ * allowed (unit is Log2). Max value is 7
+ */
+ /* 1 aggregation */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_1 0x0UL
+ /* 2 aggregations */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_2 0x1UL
+ /* 4 aggregations */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_4 0x2UL
+ /* 8 aggregations */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_8 0x3UL
+ /* 16 aggregations */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_16 0x4UL
+ /* Any aggregation size larger than this is not valid */
+ #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_MAX 0x7UL
+ uint32_t max_agg_timer;
+ /*
+ * This is the maximum amount of time allowed for an aggregation
+ * context to complete after it was initiated.
+ */
+ uint32_t min_agg_len;
+ /*
+ * This is the minimum amount of payload length required to
+ * start an aggregation context.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_cfg */
+/* Description: This function is used to enable RSS configuration. */
+/* Input (48 bytes) */
+struct hwrm_vnic_rss_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t hash_type;
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source and destination IPv4 addresses of IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV4 0x1UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination
+ * ports of TCP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV4 0x2UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination
+ * ports of UDP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV4 0x4UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source and destination IPv4 addresses of IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV6 0x8UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination
+ * ports of TCP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV6 0x10UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination
+ * ports of UDP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV6 0x20UL
+ uint32_t unused_0;
+ uint64_t ring_grp_tbl_addr;
+ /* This is the address for rss ring group table */
+ uint64_t hash_key_tbl_addr;
+ /* This is the address for rss hash key table */
+ uint16_t rss_ctx_idx;
+ /* Index to the rss indirection table. */
+ uint16_t unused_1[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_rss_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_qcfg */
+/* Description: This function is used to query RSS context configuration. */
+/* Input (24 bytes) */
+struct hwrm_vnic_rss_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t rss_ctx_idx;
+ /* Index to the rss indirection table. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (64 bytes) */
+struct hwrm_vnic_rss_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t hash_type;
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source and destination IPv4 addresses of IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_IPV4 0x1UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination
+ * ports of TCP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_TCP_IPV4 0x2UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination
+ * ports of UDP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_UDP_IPV4 0x4UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source and destination IPv4 addresses of IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_IPV6 0x8UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination
+ * ports of TCP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_TCP_IPV6 0x10UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination
+ * ports of UDP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_UDP_IPV6 0x20UL
+ uint32_t unused_0;
+ uint32_t hash_key[10];
+ /* This is the value of rss hash key */
+ uint32_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_plcmodes_cfg */
+/*
+ * Description: This function can be used to set placement mode configuration of
+ * the VNIC.
+ */
+/* Input (40 bytes) */
+struct hwrm_vnic_plcmodes_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC shall be configured to use
+ * regular placement algorithm. By default, the regular
+ * placement algorithm shall be enabled on the VNIC.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_REGULAR_PLACEMENT 0x1UL
+ /*
+ * When this bit is '1', the VNIC shall be configured use the
+ * jumbo placement algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_JUMBO_PLACEMENT 0x2UL
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable
+ * Header-Data split for IPv4 packets according to the following
+ * rules: # If the packet is identified as TCP/IPv4, then the
+ * packet is split at the beginning of the TCP payload. # If the
+ * packet is identified as UDP/IPv4, then the packet is split at
+ * the beginning of UDP payload. # If the packet is identified
+ * as non-TCP and non-UDP IPv4 packet, then the packet is split
+ * at the beginning of the upper layer protocol header carried
+ * in the IPv4 packet.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV4 0x4UL
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable
+ * Header-Data split for IPv6 packets according to the following
+ * rules: # If the packet is identified as TCP/IPv6, then the
+ * packet is split at the beginning of the TCP payload. # If the
+ * packet is identified as UDP/IPv6, then the packet is split at
+ * the beginning of UDP payload. # If the packet is identified
+ * as non-TCP and non-UDP IPv6 packet, then the packet is split
+ * at the beginning of the upper layer protocol header carried
+ * in the IPv6 packet.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV6 0x8UL
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable
+ * Header-Data split for FCoE packets at the beginning of FC
+ * payload.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_FCOE 0x10UL
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable
+ * Header-Data split for RoCE packets at the beginning of RoCE
+ * payload (after BTH/GRH headers).
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_ROCE 0x20UL
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the jumbo_thresh_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_JUMBO_THRESH_VALID 0x1UL
+ /*
+ * This bit must be '1' for the hds_offset_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_OFFSET_VALID 0x2UL
+ /*
+ * This bit must be '1' for the hds_threshold_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_THRESHOLD_VALID 0x4UL
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t jumbo_thresh;
+ /*
+ * When jumbo placement algorithm is enabled, this value is used
+ * to determine the threshold for jumbo placement. Packets with
+ * length larger than this value will be placed according to the
+ * jumbo placement algorithm.
+ */
+ uint16_t hds_offset;
+ /*
+ * This value is used to determine the offset into packet buffer
+ * where the split data (payload) will be placed according to
+ * one of of HDS placement algorithm. The lengths of packet
+ * buffers provided for split data shall be larger than this
+ * value.
+ */
+ uint16_t hds_threshold;
+ /*
+ * When one of the HDS placement algorithm is enabled, this
+ * value is used to determine the threshold for HDS placement.
+ * Packets with length larger than this value will be placed
+ * according to the HDS placement algorithm. This value shall be
+ * in multiple of 4 bytes.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_plcmodes_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_plcmodes_qcfg */
+/*
+ * Description: This function can be used to query placement mode configuration
+ * of the VNIC.
+ */
+/* Input (24 bytes) */
+struct hwrm_vnic_plcmodes_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_vnic_plcmodes_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is configured to use regular
+ * placement algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_REGULAR_PLACEMENT 0x1UL
+ /*
+ * When this bit is '1', the VNIC is configured to use the jumbo
+ * placement algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_JUMBO_PLACEMENT 0x2UL
+ /*
+ * When this bit is '1', the VNIC is configured to enable
+ * Header-Data split for IPv4 packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV4 0x4UL
+ /*
+ * When this bit is '1', the VNIC is configured to enable
+ * Header-Data split for IPv6 packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV6 0x8UL
+ /*
+ * When this bit is '1', the VNIC is configured to enable
+ * Header-Data split for FCoE packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_FCOE 0x10UL
+ /*
+ * When this bit is '1', the VNIC is configured to enable
+ * Header-Data split for RoCE packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_ROCE 0x20UL
+ /*
+ * When this bit is '1', the VNIC is configured to be the
+ * default VNIC of the requesting function.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_DFLT_VNIC 0x40UL
+ uint16_t jumbo_thresh;
+ /*
+ * When jumbo placement algorithm is enabled, this value is used
+ * to determine the threshold for jumbo placement. Packets with
+ * length larger than this value will be placed according to the
+ * jumbo placement algorithm.
+ */
+ uint16_t hds_offset;
+ /*
+ * This value is used to determine the offset into packet buffer
+ * where the split data (payload) will be placed according to
+ * one of of HDS placement algorithm. The lengths of packet
+ * buffers provided for split data shall be larger than this
+ * value.
+ */
+ uint16_t hds_threshold;
+ /*
+ * When one of the HDS placement algorithm is enabled, this
+ * value is used to determine the threshold for HDS placement.
+ * Packets with length larger than this value will be placed
+ * according to the HDS placement algorithm. This value shall be
+ * in multiple of 4 bytes.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_cos_lb_ctx_alloc */
+/* Description: This function is used to allocate COS/Load Balance context. */
+/* Input (16 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t rss_cos_lb_ctx_id;
+ /* rss_cos_lb_ctx_id is 16 b */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_cos_lb_ctx_free */
+/* Description: This function can be used to free COS/Load Balance context. */
+/* Input (24 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t rss_cos_lb_ctx_id;
+ /* rss_cos_lb_ctx_id is 16 b */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_alloc */
+/*
+ * Description: This command allocates and does basic preparation for a ring.
+ */
+/* Input (80 bytes) */
+struct hwrm_ring_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the Reserved1 field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED1 0x1UL
+ /* This bit must be '1' for the ring_arb_cfg field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RING_ARB_CFG 0x2UL
+ /* This bit must be '1' for the Reserved3 field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED3 0x4UL
+ /*
+ * This bit must be '1' for the stat_ctx_id_valid field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_STAT_CTX_ID_VALID 0x8UL
+ /* This bit must be '1' for the Reserved4 field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED4 0x10UL
+ /* This bit must be '1' for the max_bw_valid field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_MAX_BW_VALID 0x20UL
+ uint8_t ring_type;
+ /* Ring Type. */
+ /* L2 Completion Ring (CR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_L2_CMPL 0x0UL
+ /* TX Ring (TR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_TX 0x1UL
+ /* RX Ring (RR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_RX 0x2UL
+ /* RoCE Notification Completion Ring (ROCE_CR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_ROCE_CMPL 0x3UL
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint64_t page_tbl_addr;
+ /* This value is a pointer to the page table for the Ring. */
+ uint32_t fbo;
+ /* First Byte Offset of the first entry in the first page. */
+ uint8_t page_size;
+ /*
+ * Actual page size in 2^page_size. The supported range is
+ * increments in powers of 2 from 16 bytes to 1GB. - 4 = 16 B
+ * Page size is 16 B. - 12 = 4 KB Page size is 4 KB. - 13 = 8 KB
+ * Page size is 8 KB. - 16 = 64 KB Page size is 64 KB. - 21 = 2
+ * MB Page size is 2 MB. - 22 = 4 MB Page size is 4 MB. - 30 = 1
+ * GB Page size is 1 GB.
+ */
+ uint8_t page_tbl_depth;
+ /*
+ * This value indicates the depth of page table. For this
+ * version of the specification, value other than 0 or 1 shall
+ * be considered as an invalid value. When the page_tbl_depth =
+ * 0, then it is treated as a special case with the following.
+ * 1. FBO and page size fields are not valid. 2. page_tbl_addr
+ * is the physical address of the first element of the ring.
+ */
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint32_t length;
+ /*
+ * Number of 16B units in the ring. Minimum size for a ring is
+ * 16 16B entries.
+ */
+ uint16_t logical_id;
+ /*
+ * Logical ring number for the ring to be allocated. This value
+ * determines the position in the doorbell area where the update
+ * to the ring will be made. For completion rings, this value is
+ * also the MSI-X vector number for the function the completion
+ * ring is associated with.
+ */
+ uint16_t cmpl_ring_id;
+ /*
+ * This field is used only when ring_type is a TX ring. This
+ * value indicates what completion ring the TX ring is
+ * associated with.
+ */
+ uint16_t queue_id;
+ /*
+ * This field is used only when ring_type is a TX ring. This
+ * value indicates what CoS queue the TX ring is associated
+ * with.
+ */
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint32_t reserved1;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint16_t ring_arb_cfg;
+ /*
+ * This field is used only when ring_type is a TX ring. This
+ * field is used to configure arbitration related parameters for
+ * a TX ring.
+ */
+ /* Arbitration policy used for the ring. */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_MASK 0xfUL
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_SFT 0
+ /*
+ * Use strict priority for the TX ring. Priority
+ * value is specified in arb_policy_param
+ */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_SP (0x1UL << 0)
+ /*
+ * Use weighted fair queue arbitration for the
+ * TX ring. Weight is specified in
+ * arb_policy_param
+ */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_WFQ (0x2UL << 0)
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_LAST \
+ HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_WFQ
+ /* Reserved field. */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_RSVD_MASK 0xf0UL
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_RSVD_SFT 4
+ /*
+ * Arbitration policy specific parameter. # For strict priority
+ * arbitration policy, this field represents a priority value.
+ * If set to 0, then the priority is not specified and the HWRM
+ * is allowed to select any priority for this TX ring. # For
+ * weighted fair queue arbitration policy, this field represents
+ * a weight value. If set to 0, then the weight is not specified
+ * and the HWRM is allowed to select any weight for this TX
+ * ring.
+ */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_PARAM_MASK \
+ 0xff00UL
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_PARAM_SFT 8
+ uint8_t unused_6;
+ uint8_t unused_7;
+ uint32_t reserved3;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t stat_ctx_id;
+ /*
+ * This field is used only when ring_type is a TX ring. This
+ * input indicates what statistics context this ring should be
+ * associated with.
+ */
+ uint32_t reserved4;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t max_bw;
+ /*
+ * This field is used only when ring_type is a TX ring to
+ * specify maximum BW allocated to the TX ring. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for this ring inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_MASK 0xfffffffUL
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BITS (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BYTES (0x1UL << 28)
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_LAST \
+ HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_MASK 0xe0000000UL
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_KILO (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_BASE (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID (0x7UL << 29)
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
+ RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t int_mode;
+ /*
+ * This field is used only when ring_type is a Completion ring.
+ * This value indicates what interrupt mode should be used on
+ * this completion ring. Note: In the legacy interrupt mode, no
+ * more than 16 completion rings are allowed.
+ */
+ /* Legacy INTA */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_LEGACY 0x0UL
+ /* Reserved */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_RSVD 0x1UL
+ /* MSI-X */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_MSIX 0x2UL
+ /* No Interrupt - Polled mode */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_POLL 0x3UL
+ uint8_t unused_8[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t ring_id;
+ /*
+ * Physical number of ring allocated. This value shall be unique
+ * for a ring type.
+ */
+ uint16_t logical_ring_id;
+ /* Logical number of ring allocated. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_free */
+/*
+ * Description: This command is used to free a ring and associated resources.
+ * With QoS and DCBx agents, it is possible the traffic classes will be moved
+ * from one CoS queue to another. When this occurs, the driver shall call
+ * 'hwrm_ring_free' to free the allocated rings and then call 'hwrm_ring_alloc'
+ * to re-allocate each ring and assign it to a new CoS queue. hwrm_ring_free
+ * shall be called on a ring only after it has been idle for 500ms or more and
+ * no frames have been posted to the ring during this time. All frames queued
+ * for transmission shall be completed and at least 500ms time elapsed from the
+ * last completion before calling this command.
+ */
+/* Input (24 bytes) */
+struct hwrm_ring_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint8_t ring_type;
+ /* Ring Type. */
+ /* L2 Completion Ring (CR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_L2_CMPL 0x0UL
+ /* TX Ring (TR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_TX 0x1UL
+ /* RX Ring (RR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_RX 0x2UL
+ /* RoCE Notification Completion Ring (ROCE_CR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_ROCE_CMPL 0x3UL
+ uint8_t unused_0;
+ uint16_t ring_id;
+ /* Physical number of ring allocated. */
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_cmpl_ring_qaggint_params */
+/*
+ * Description: This command is used to query aggregation and interrupt related
+ * parameters specified on a given completion ring.
+ */
+/* Input (24 bytes) */
+struct hwrm_ring_cmpl_ring_qaggint_params_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t ring_id;
+ /* Physical number of completion ring. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (32 bytes) */
+struct hwrm_ring_cmpl_ring_qaggint_params_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t flags;
+ /*
+ * When this bit is set to '1', interrupt max timer is reset
+ * whenever a completion is received.
+ */
+ #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_OUTPUT_FLAGS_TIMER_RESET \
+ 0x1UL
+ /*
+ * When this bit is set to '1', ring idle mode aggregation will
+ * be enabled.
+ */
+ #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_OUTPUT_FLAGS_RING_IDLE 0x2UL
+ uint16_t num_cmpl_dma_aggr;
+ /*
+ * Number of completions to aggregate before DMA during the
+ * normal mode.
+ */
+ uint16_t num_cmpl_dma_aggr_during_int;
+ /*
+ * Number of completions to aggregate before DMA during the
+ * interrupt mode.
+ */
+ uint16_t cmpl_aggr_dma_tmr;
+ /*
+ * Timer in unit of 80-nsec used to aggregate completions before
+ * DMA during the normal mode (not in interrupt mode).
+ */
+ uint16_t cmpl_aggr_dma_tmr_during_int;
+ /*
+ * Timer in unit of 80-nsec used to aggregate completions before
+ * DMA during the interrupt mode.
+ */
+ uint16_t int_lat_tmr_min;
+ /* Minimum time (in unit of 80-nsec) between two interrupts. */
+ uint16_t int_lat_tmr_max;
+ /*
+ * Maximum wait time (in unit of 80-nsec) spent aggregating
+ * completions before signaling the interrupt after the
+ * interrupt is enabled.
+ */
+ uint16_t num_cmpl_aggr_int;
+ /*
+ * Minimum number of completions aggregated before signaling an
+ * interrupt.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_cmpl_ring_cfg_aggint_params */
+/*
+ * Description: This command is used to configure aggregation and interrupt
+ * related parameters specified on a given completion ring.
+ */
+/* Input (40 bytes) */
+struct hwrm_ring_cmpl_ring_cfg_aggint_params_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t ring_id;
+ /* Physical number of completion ring. */
+ uint16_t flags;
+ /*
+ * When this bit is set to '1', interrupt latency max timer is
+ * reset whenever a completion is received.
+ */
+ #define \
+ HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_FLAGS_TIMER_RESET 0x1UL
+ /*
+ * When this bit is set to '1', ring idle mode aggregation will
+ * be enabled.
+ */
+ #define \
+ HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_FLAGS_RING_IDLE 0x2UL
+ uint16_t num_cmpl_dma_aggr;
+ /*
+ * Number of completions to aggregate before DMA during the
+ * normal mode.
+ */
+ uint16_t num_cmpl_dma_aggr_during_int;
+ /*
+ * Number of completions to aggregate before DMA during the
+ * interrupt mode.
+ */
+ uint16_t cmpl_aggr_dma_tmr;
+ /*
+ * Timer in unit of 80-nsec used to aggregate completions before
+ * DMA during the normal mode (not in interrupt mode).
+ */
+ uint16_t cmpl_aggr_dma_tmr_during_int;
+ /*
+ * Timer in unit of 80-nsec used to aggregate completions before
+ * DMA during the interrupt mode.
+ */
+ uint16_t int_lat_tmr_min;
+ /* Minimum time (in unit of 80-nsec) between two interrupts. */
+ uint16_t int_lat_tmr_max;
+ /*
+ * Maximum wait time (in unit of 80-nsec) spent aggregating
+ * cmpls before signaling the interrupt after the interrupt is
+ * enabled.
+ */
+ uint16_t num_cmpl_aggr_int;
+ /*
+ * Minimum number of completions aggregated before signaling an
+ * interrupt.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_cmpl_ring_cfg_aggint_params_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_reset */
+/*
+ * Description: This command is used to reset a given ring. When an RX ring is
+ * being reset, the HWRM shall perform TPA flush on all VNICs associated with
+ * the RX ring that is being reset.
+ */
+/* Input (24 bytes) */
+struct hwrm_ring_reset_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint8_t ring_type;
+ /* Ring Type. */
+ /* L2 Completion Ring (CR) */
+ #define HWRM_RING_RESET_INPUT_RING_TYPE_L2_CMPL 0x0UL
+ /* TX Ring (TR) */
+ #define HWRM_RING_RESET_INPUT_RING_TYPE_TX 0x1UL
+ /* RX Ring (RR) */
+ #define HWRM_RING_RESET_INPUT_RING_TYPE_RX 0x2UL
+ /* RoCE Notification Completion Ring (ROCE_CR) */
+ #define HWRM_RING_RESET_INPUT_RING_TYPE_ROCE_CMPL 0x3UL
+ uint8_t unused_0;
+ uint16_t ring_id;
+ /* Physical number of the ring. */
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_reset_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_grp_alloc */
+/*
+ * Description: This API allocates and does basic preparation for a ring group.
+ */
+/* Input (24 bytes) */
+struct hwrm_ring_grp_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t cr;
+ /* This value identifies the CR associated with the ring group. */
+ uint16_t rr;
+ /* This value identifies the main RR associated with the ring group. */
+ uint16_t ar;
+ /*
+ * This value identifies the aggregation RR associated with the
+ * ring group. If this value is 0xFF... (All Fs), then no
+ * Aggregation ring will be set.
+ */
+ uint16_t sc;
+ /*
+ * This value identifies the statistics context associated with
+ * the ring group.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_grp_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t ring_group_id;
+ /*
+ * This is the ring group ID value. Use this value to program
+ * the default ring group for the VNIC or as table entries in an
+ * RSS/COS context.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_grp_free */
+/*
+ * Description: This API frees a ring group and associated resources. # If a
+ * ring in the ring group is reset or free, then the associated rings in the
+ * ring group shall also be reset/free using hwrm_ring_free. # A function driver
+ * shall always use hwrm_ring_grp_free after freeing all rings in a group. # As
+ * a part of executing this command, the HWRM shall reset all associated ring
+ * group resources.
+ */
+/* Input (24 bytes) */
+struct hwrm_ring_grp_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t ring_group_id;
+ /* This is the ring group ID value. */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_grp_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_filter_alloc */
+/*
+ * Description: An L2 filter is a filter resource that is used to identify a
+ * vnic or ring for a packet based on layer 2 fields. Layer 2 fields for
+ * encapsulated packets include both outer L2 header and/or inner l2 header of
+ * encapsulated packet. The L2 filter resource covers the following OS specific
+ * L2 filters. Linux/FreeBSD (per function): # Broadcast enable/disable # List
+ * of individual multicast filters # All multicast enable/disable filter #
+ * Unicast filters # Promiscuous mode VMware: # Broadcast enable/disable (per
+ * physical function) # All multicast enable/disable (per function) # Unicast
+ * filters per ring or vnic # Promiscuous mode per PF Windows: # Broadcast
+ * enable/disable (per physical function) # List of individual multicast filters
+ * (Driver needs to advertise the maximum number of filters supported) # All
+ * multicast enable/disable per physical function # Unicast filters per vnic #
+ * Promiscuous mode per PF Implementation notes on the use of VNIC in this
+ * command: # By default, these filters belong to default vnic for the function.
+ * # Once these filters are set up, only destination VNIC can be modified. # If
+ * the destination VNIC is not specified in this command, then the HWRM shall
+ * only create an l2 context id. HWRM Implementation notes for multicast
+ * filters: # The hwrm_filter_alloc command can be used to set up multicast
+ * filters (perfect match or partial match). Each individual function driver can
+ * set up multicast filters independently. # The HWRM needs to keep track of
+ * multicast filters set up by function drivers and maintain multicast group
+ * replication records to enable a subset of functions to receive traffic for a
+ * specific multicast address. # When a specific multicast filter cannot be set,
+ * the HWRM shall return an error. In this error case, the driver should fall
+ * back to using one general filter (rather than specific) for all multicast
+ * traffic. # When the SR-IOV is enabled, the HWRM needs to additionally track
+ * source knockout per multicast group record. Examples of setting unicast
+ * filters: For a unicast MAC based filter, one can use a combination of the
+ * fields and masks provided in this command to set up the filter. Below are
+ * some examples: # MAC + no VLAN filter: This filter is used to identify
+ * traffic that does not contain any VLAN tags and matches destination (or
+ * source) MAC address. This filter can be set up by setting only l2_addr field
+ * to be a valid field. All other fields are not valid. The following value is
+ * set for l2_addr. l2_addr = MAC # MAC + Any VLAN filter: This filter is used
+ * to identify traffic that carries single VLAN tag and matches (destination or
+ * source) MAC address. This filter can be set up by setting only l2_addr and
+ * l2_ovlan_mask fields to be valid fields. All other fields are not valid. The
+ * following values are set for those two valid fields. l2_addr = MAC,
+ * l2_ovlan_mask = 0xFFFF # MAC + no VLAN or VLAN ID=0: This filter is used to
+ * identify untagged traffic that does not contain any VLAN tags or a VLAN tag
+ * with VLAN ID = 0 and matches destination (or source) MAC address. This filter
+ * can be set up by setting only l2_addr and l2_ovlan fields to be valid fields.
+ * All other fields are not valid. The following value are set for l2_addr and
+ * l2_ovlan. l2_addr = MAC, l2_ovlan = 0x0 # MAC + no VLAN or any VLAN: This
+ * filter is used to identify traffic that contains zero or 1 VLAN tag and
+ * matches destination (or source) MAC address. This filter can be set up by
+ * setting only l2_addr, l2_ovlan, and l2_mask fields to be valid fields. All
+ * other fields are not valid. The following value are set for l2_addr,
+ * l2_ovlan, and l2_mask fields. l2_addr = MAC, l2_ovlan = 0x0, l2_ovlan_mask =
+ * 0xFFFF # MAC + VLAN ID filter: This filter can be set up by setting only
+ * l2_addr, l2_ovlan, and l2_ovlan_mask fields to be valid fields. All other
+ * fields are not valid. The following values are set for those three valid
+ * fields. l2_addr = MAC, l2_ovlan = VLAN ID, l2_ovlan_mask = 0xF000
+ */
+/* Input (96 bytes) */
+struct hwrm_cfa_l2_filter_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_TX (0x0UL << 0)
+ /* rx path */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX (0x1UL << 0)
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_LAST \
+ CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX
+ /*
+ * Setting of this flag indicates the applicability to the
+ * loopback path.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK 0x2UL
+ /*
+ * Setting of this flag indicates drop action. If this flag is
+ * not set, then it should be considered accept action.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_DROP 0x4UL
+ /*
+ * If this flag is set, all t_l2_* fields are invalid and they
+ * should not be specified. If this flag is set, then l2_*
+ * fields refer to fields of outermost L2 header.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_OUTERMOST 0x8UL
+ uint32_t enables;
+ /* This bit must be '1' for the l2_addr field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR 0x1UL
+ /* This bit must be '1' for the l2_addr_mask field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR_MASK 0x2UL
+ /* This bit must be '1' for the l2_ovlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN 0x4UL
+ /*
+ * This bit must be '1' for the l2_ovlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN_MASK 0x8UL
+ /* This bit must be '1' for the l2_ivlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN 0x10UL
+ /*
+ * This bit must be '1' for the l2_ivlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN_MASK 0x20UL
+ /* This bit must be '1' for the t_l2_addr field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR 0x40UL
+ /*
+ * This bit must be '1' for the t_l2_addr_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR_MASK 0x80UL
+ /* This bit must be '1' for the t_l2_ovlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN 0x100UL
+ /*
+ * This bit must be '1' for the t_l2_ovlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN_MASK 0x200UL
+ /* This bit must be '1' for the t_l2_ivlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN 0x400UL
+ /*
+ * This bit must be '1' for the t_l2_ivlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN_MASK 0x800UL
+ /* This bit must be '1' for the src_type field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_TYPE 0x1000UL
+ /* This bit must be '1' for the src_id field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_ID 0x2000UL
+ /* This bit must be '1' for the tunnel_type field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE 0x4000UL
+ /* This bit must be '1' for the dst_id field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_DST_ID 0x8000UL
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID 0x10000UL
+ uint8_t l2_addr[6];
+ /*
+ * This value sets the match value for the L2 MAC address.
+ * Destination MAC address for RX path. Source MAC address for
+ * TX path.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t l2_addr_mask[6];
+ /*
+ * This value sets the mask value for the L2 address. A value of
+ * 0 will mask the corresponding bit from compare.
+ */
+ uint16_t l2_ovlan;
+ /* This value sets VLAN ID value for outer VLAN. */
+ uint16_t l2_ovlan_mask;
+ /*
+ * This value sets the mask value for the ovlan id. A value of 0
+ * will mask the corresponding bit from compare.
+ */
+ uint16_t l2_ivlan;
+ /* This value sets VLAN ID value for inner VLAN. */
+ uint16_t l2_ivlan_mask;
+ /*
+ * This value sets the mask value for the ivlan id. A value of 0
+ * will mask the corresponding bit from compare.
+ */
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t t_l2_addr[6];
+ /*
+ * This value sets the match value for the tunnel L2 MAC
+ * address. Destination MAC address for RX path. Source MAC
+ * address for TX path.
+ */
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t t_l2_addr_mask[6];
+ /*
+ * This value sets the mask value for the tunnel L2 address. A
+ * value of 0 will mask the corresponding bit from compare.
+ */
+ uint16_t t_l2_ovlan;
+ /* This value sets VLAN ID value for tunnel outer VLAN. */
+ uint16_t t_l2_ovlan_mask;
+ /*
+ * This value sets the mask value for the tunnel ovlan id. A
+ * value of 0 will mask the corresponding bit from compare.
+ */
+ uint16_t t_l2_ivlan;
+ /* This value sets VLAN ID value for tunnel inner VLAN. */
+ uint16_t t_l2_ivlan_mask;
+ /*
+ * This value sets the mask value for the tunnel ivlan id. A
+ * value of 0 will mask the corresponding bit from compare.
+ */
+ uint8_t src_type;
+ /* This value identifies the type of source of the packet. */
+ /* Network port */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_NPORT 0x0UL
+ /* Physical function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_PF 0x1UL
+ /* Virtual function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VF 0x2UL
+ /* Virtual NIC of a function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VNIC 0x3UL
+ /* Embedded processor for CFA management */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_KONG 0x4UL
+ /* Embedded processor for OOB management */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_APE 0x5UL
+ /* Embedded processor for RoCE */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_BONO 0x6UL
+ /* Embedded processor for network proxy functions */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_TANG 0x7UL
+ uint8_t unused_6;
+ uint32_t src_id;
+ /*
+ * This value is the id of the source. For a network port, it
+ * represents port_id. For a physical function, it represents
+ * fid. For a virtual function, it represents vf_id. For a vnic,
+ * it represents vnic_id. For embedded processors, this id is
+ * not valid. Notes: 1. The function ID is implied if it src_id
+ * is not provided for a src_type that is either
+ */
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Non-tunnel */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL 0x0UL
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN 0x1UL
+ /*
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE 0x2UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside
+ * Ethernet payload
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE 0x3UL
+ /* IP in IP */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP 0x4UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE 0x5UL
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS 0x6UL
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT 0x7UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE 0x8UL
+ /*
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 0x9UL
+ /* Any tunneled traffic */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL 0xffUL
+ uint8_t unused_7;
+ uint16_t dst_id;
+ /*
+ * If set, this value shall represent the Logical VNIC ID of the
+ * destination VNIC for the RX path and network port id of the
+ * destination port for the TX path.
+ */
+ uint16_t mirror_vnic_id;
+ /* Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint8_t pri_hint;
+ /*
+ * This hint is provided to help in placing the filter in the
+ * filter table.
+ */
+ /* No preference */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER 0x0UL
+ /* Above the given filter */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE_FILTER 0x1UL
+ /* Below the given filter */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_BELOW_FILTER 0x2UL
+ /* As high as possible */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MAX 0x3UL
+ /* As low as possible */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MIN 0x4UL
+ uint8_t unused_8;
+ uint32_t unused_9;
+ uint64_t l2_filter_id_hint;
+ /*
+ * This is the ID of the filter that goes along with the
+ * pri_hint. This field is valid only for the following values.
+ * 1 - Above the given filter 2 - Below the given filter
+ */
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_cfa_l2_filter_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint64_t l2_filter_id;
+ /*
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
+ */
+ uint32_t flow_id;
+ /*
+ * This is the ID of the flow associated with this filter. This
+ * value shall be used to match and associate the flow
+ * identifier returned in completion records. A value of
+ * 0xFFFFFFFF shall indicate no flow id.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_filter_free */
+/*
+ * Description: Free a L2 filter. The HWRM shall free all associated filter
+ * resources with the L2 filter.
+ */
+/* Input (24 bytes) */
+struct hwrm_cfa_l2_filter_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint64_t l2_filter_id;
+ /*
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_l2_filter_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_filter_cfg */
+/* Description: Change the configuration of an existing L2 filter */
+/* Input (40 bytes) */
+struct hwrm_cfa_l2_filter_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_TX (0x0UL << 0)
+ /* rx path */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_RX (0x1UL << 0)
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_LAST \
+ CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_RX
+ /*
+ * Setting of this flag indicates drop action. If this flag is
+ * not set, then it should be considered accept action.
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_DROP 0x2UL
+ uint32_t enables;
+ /* This bit must be '1' for the dst_id field to be configured. */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_ENABLES_DST_ID 0x1UL
+ /*
+ * This bit must be '1' for the new_mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID 0x2UL
+ uint64_t l2_filter_id;
+ /*
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
+ */
+ uint32_t dst_id;
+ /*
+ * If set, this value shall represent the Logical VNIC ID of the
+ * destination VNIC for the RX path and network port id of the
+ * destination port for the TX path.
+ */
+ uint32_t new_mirror_vnic_id;
+ /* New Logical VNIC ID of the VNIC where traffic is mirrored. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_l2_filter_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_set_rx_mask */
+/* Description: This command will set rx mask of the function. */
+/* Input (56 bytes) */
+struct hwrm_cfa_l2_set_rx_mask_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
* - HWRM
*/
uint64_t resp_addr;
@@ -1863,37 +19336,298 @@ struct hwrm_ver_get_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint8_t hwrm_intf_maj;
+ uint32_t vnic_id;
+ /* VNIC ID */
+ uint32_t mask;
+ /* Reserved for future use. */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_RESERVED 0x1UL
/*
- * This field represents the major version of HWRM interface
- * specification supported by the driver HWRM implementation.
- * The interface major version is intended to change only when
- * non backward compatible changes are made to the HWRM
- * interface specification.
+ * When this bit is '1', the function is requested to accept
+ * multi-cast packets specified by the multicast addr table.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_MCAST 0x2UL
+ /*
+ * When this bit is '1', the function is requested to accept all
+ * multi-cast packets.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ALL_MCAST 0x4UL
+ /*
+ * When this bit is '1', the function is requested to accept
+ * broadcast packets.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_BCAST 0x8UL
+ /*
+ * When this bit is '1', the function is requested to be put in
+ * the promiscuous mode. The HWRM should accept any function to
+ * set up promiscuous mode. The HWRM shall follow the semantics
+ * below for the promiscuous mode support. # When partitioning
+ * is not enabled on a port (i.e. single PF on the port), then
+ * the PF shall be allowed to be in the promiscuous mode. When
+ * the PF is in the promiscuous mode, then it shall receive all
+ * host bound traffic on that port. # When partitioning is
+ * enabled on a port (i.e. multiple PFs per port) and a PF on
+ * that port is in the promiscuous mode, then the PF receives
+ * all traffic within that partition as identified by a unique
+ * identifier for the PF (e.g. S-Tag). If a unique outer VLAN
+ * for the PF is specified, then the setting of promiscuous mode
+ * on that PF shall result in the PF receiving all host bound
+ * traffic with matching outer VLAN. # A VF shall can be set in
+ * the promiscuous mode. In the promiscuous mode, the VF does
+ * not receive any traffic unless a unique outer VLAN for the VF
+ * is specified. If a unique outer VLAN for the VF is specified,
+ * then the setting of promiscuous mode on that VF shall result
+ * in the VF receiving all host bound traffic with the matching
+ * outer VLAN. # The HWRM shall allow the setting of promiscuous
+ * mode on a function independently from the promiscuous mode
+ * settings on other functions.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_PROMISCUOUS 0x10UL
+ /*
+ * If this flag is set, the corresponding RX filters shall be
+ * set up to cover multicast/broadcast filters for the outermost
+ * Layer 2 destination MAC address field.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_OUTERMOST 0x20UL
+ /*
+ * If this flag is set, the corresponding RX filters shall be
+ * set up to cover multicast/broadcast filters for the VLAN-
+ * tagged packets that match the TPID and VID fields of VLAN
+ * tags in the VLAN tag table specified in this command.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_VLANONLY 0x40UL
+ /*
+ * If this flag is set, the corresponding RX filters shall be
+ * set up to cover multicast/broadcast filters for non-VLAN
+ * tagged packets and VLAN-tagged packets that match the TPID
+ * and VID fields of VLAN tags in the VLAN tag table specified
+ * in this command.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_VLAN_NONVLAN 0x80UL
+ /*
+ * If this flag is set, the corresponding RX filters shall be
+ * set up to cover multicast/broadcast filters for non-VLAN
+ * tagged packets and VLAN-tagged packets matching any VLAN tag.
+ * If this flag is set, then the HWRM shall ignore VLAN tags
+ * specified in vlan_tag_tbl. If none of vlanonly, vlan_nonvlan,
+ * and anyvlan_nonvlan flags is set, then the HWRM shall ignore
+ * VLAN tags specified in vlan_tag_tbl. The HWRM client shall
+ * set at most one flag out of vlanonly, vlan_nonvlan, and
+ * anyvlan_nonvlan.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ANYVLAN_NONVLAN 0x100UL
+ uint64_t mc_tbl_addr;
+ /* This is the address for mcast address tbl. */
+ uint32_t num_mc_entries;
+ /*
+ * This value indicates how many entries in mc_tbl are valid.
+ * Each entry is 6 bytes.
+ */
+ uint32_t unused_0;
+ uint64_t vlan_tag_tbl_addr;
+ /*
+ * This is the address for VLAN tag table. Each VLAN entry in
+ * the table is 4 bytes of a VLAN tag including TPID, PCP, DEI,
+ * and VID fields in network byte order.
+ */
+ uint32_t num_vlan_tags;
+ /*
+ * This value indicates how many entries in vlan_tag_tbl are
+ * valid. Each entry is 4 bytes.
+ */
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_l2_set_rx_mask_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_cfa_l2_set_rx_mask_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_UNKNOWN 0x0UL
+ /*
+ * Unable to complete operation due to conflict
+ * with Ntuple Filter
+ */
+ #define \
+ HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_NTUPLE_FILTER_CONFLICT_ERR \
+ 0x1UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* hwrm_cfa_vlan_antispoof_cfg */
+/* Description: Configures vlan anti-spoof filters for VF. */
+/* Input (32 bytes) */
+struct hwrm_cfa_vlan_antispoof_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. Only
+ * valid for a VF FID configured by the PF.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t num_vlan_entries;
+ /* Number of VLAN entries in the vlan_tag_mask_tbl. */
+ uint64_t vlan_tag_mask_tbl_addr;
+ /*
+ * The vlan_tag_mask_tbl_addr is the DMA address of the VLAN
+ * antispoof table. Each table entry contains the 16-bit TPID
+ * (0x8100 or 0x88a8 only), 16-bit VLAN ID, and a 16-bit mask,
+ * all in network order to match hwrm_cfa_l2_set_rx_mask. For an
+ * individual VLAN entry, the mask value should be 0xfff for the
+ * 12-bit VLAN ID.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_vlan_antispoof_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_vlan_antispoof_qcfg */
+/*
+ * Description: Returns the current configuration of the vlan anti-spoof filters
+ * for VF.
+ */
+/* Input (32 bytes) */
+struct hwrm_cfa_vlan_antispoof_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint8_t hwrm_intf_min;
+ uint16_t fid;
/*
- * This field represents the minor version of HWRM interface
- * specification supported by the driver HWRM implementation. A
- * change in interface minor version is used to reflect
- * significant backward compatible modification to HWRM
- * interface specification. This can be due to addition or
- * removal of functionality. HWRM interface specifications with
- * the same major version but different minor versions are
- * compatible.
+ * Function ID of the function that is being queried. Only valid
+ * for a VF FID queried by the PF.
*/
- uint8_t hwrm_intf_upd;
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t max_vlan_entries;
/*
- * This field represents the update version of HWRM interface
- * specification supported by the driver HWRM implementation.
- * The interface update version is used to reflect minor changes
- * or bug fixes to a released HWRM interface specification.
+ * Maximum number of VLAN entries the firmware is allowed to DMA
+ * to vlan_tag_mask_tbl.
+ */
+ uint64_t vlan_tag_mask_tbl_addr;
+ /*
+ * The vlan_tag_mask_tbl_addr is the DMA address of the VLAN
+ * antispoof table to which firmware will DMA to. Each table
+ * entry will contain the 16-bit TPID (0x8100 or 0x88a8 only),
+ * 16-bit VLAN ID, and a 16-bit mask, all in network order to
+ * match hwrm_cfa_l2_set_rx_mask. For an individual VLAN entry,
+ * the mask value should be 0xfff for the 12-bit VLAN ID.
*/
- uint8_t unused_0[5];
} __attribute__((packed));
-/* Output (128 bytes) */
-struct hwrm_ver_get_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_vlan_antispoof_qcfg_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -1909,220 +19643,277 @@ struct hwrm_ver_get_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint8_t hwrm_intf_maj;
- /*
- * This field represents the major version of HWRM interface
- * specification supported by the HWRM implementation. The
- * interface major version is intended to change only when non
- * backward compatible changes are made to the HWRM interface
- * specification. A HWRM implementation that is compliant with
- * this specification shall provide value of 1 in this field.
- */
- uint8_t hwrm_intf_min;
- /*
- * This field represents the minor version of HWRM interface
- * specification supported by the HWRM implementation. A change
- * in interface minor version is used to reflect significant
- * backward compatible modification to HWRM interface
- * specification. This can be due to addition or removal of
- * functionality. HWRM interface specifications with the same
- * major version but different minor versions are compatible. A
- * HWRM implementation that is compliant with this specification
- * shall provide value of 2 in this field.
- */
- uint8_t hwrm_intf_upd;
+ uint32_t num_vlan_entries;
+ /* Number of valid entries DMAd by firmware to vlan_tag_mask_tbl. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
/*
- * This field represents the update version of HWRM interface
- * specification supported by the HWRM implementation. The
- * interface update version is used to reflect minor changes or
- * bug fixes to a released HWRM interface specification. A HWRM
- * implementation that is compliant with this specification
- * shall provide value of 2 in this field.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- uint8_t hwrm_intf_rsvd;
- uint8_t hwrm_fw_maj;
+} __attribute__((packed));
+
+/* hwrm_cfa_tunnel_filter_alloc */
+/*
+ * Description: This is a tunnel filter that uses fields from tunnel header in
+ * addition to l2 context. The tunnel filter applies to receive side only. The
+ * l2_* fields in this command represent fields of inner L2 header. They are
+ * optional to be specified. It allows l2_filter_id to be created with outer L2
+ * header fields that can be shared with multiple tunnel filters specified as
+ * combinations of inner L2 header fields, tunnel type, and VNI.
+ */
+/* Input (88 bytes) */
+struct hwrm_cfa_tunnel_filter_alloc_input {
+ uint16_t req_type;
/*
- * This field represents the major version of HWRM firmware. A
- * change in firmware major version represents a major firmware
- * release.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- uint8_t hwrm_fw_min;
+ uint16_t cmpl_ring;
/*
- * This field represents the minor version of HWRM firmware. A
- * change in firmware minor version represents significant
- * firmware functionality changes.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- uint8_t hwrm_fw_bld;
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * This field represents the build version of HWRM firmware. A
- * change in firmware build version represents bug fixes to a
- * released firmware.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint8_t hwrm_fw_rsvd;
+ uint64_t resp_addr;
/*
- * This field is a reserved field. This field can be used to
- * represent firmware branches or customer specific releases
- * tied to a specific (major,minor,update) version of the HWRM
- * firmware.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint8_t mgmt_fw_maj;
+ uint32_t flags;
/*
- * This field represents the major version of mgmt firmware. A
- * change in major version represents a major release.
+ * Setting of this flag indicates the applicability to the
+ * loopback path.
*/
- uint8_t mgmt_fw_min;
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK 0x1UL
+ uint32_t enables;
+ /* This bit must be '1' for the l2_filter_id field to be configured. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_FILTER_ID 0x1UL
+ /* This bit must be '1' for the l2_addr field to be configured. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR 0x2UL
+ /* This bit must be '1' for the l2_ivlan field to be configured. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN 0x4UL
+ /* This bit must be '1' for the l3_addr field to be configured. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L3_ADDR 0x8UL
+ /* This bit must be '1' for the l3_addr_type field to be configured. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L3_ADDR_TYPE 0x10UL
/*
- * This field represents the minor version of mgmt firmware. A
- * change in minor version represents significant functionality
- * changes.
+ * This bit must be '1' for the t_l3_addr_type field to be
+ * configured.
*/
- uint8_t mgmt_fw_bld;
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_T_L3_ADDR_TYPE 0x20UL
+ /* This bit must be '1' for the t_l3_addr field to be configured. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_T_L3_ADDR 0x40UL
+ /* This bit must be '1' for the tunnel_type field to be configured. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE 0x80UL
+ /* This bit must be '1' for the vni field to be configured. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_VNI 0x100UL
+ /* This bit must be '1' for the dst_vnic_id field to be configured. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_DST_VNIC_ID 0x200UL
/*
- * This field represents the build version of mgmt firmware. A
- * change in update version represents bug fixes.
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
*/
- uint8_t mgmt_fw_rsvd;
+ #define \
+ HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID 0x400UL
+ uint64_t l2_filter_id;
/*
- * This field is a reserved field. This field can be used to
- * represent firmware branches or customer specific releases
- * tied to a specific (major,minor,update) version
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
*/
- uint8_t netctrl_fw_maj;
+ uint8_t l2_addr[6];
/*
- * This field represents the major version of network control
- * firmware. A change in major version represents a major
- * release.
+ * This value sets the match value for the inner L2 MAC address.
+ * Destination MAC address for RX path. Source MAC address for
+ * TX path.
*/
- uint8_t netctrl_fw_min;
+ uint16_t l2_ivlan;
/*
- * This field represents the minor version of network control
- * firmware. A change in minor version represents significant
- * functionality changes.
+ * This value sets VLAN ID value for inner VLAN. Only 12-bits of
+ * VLAN ID are used in setting the filter.
*/
- uint8_t netctrl_fw_bld;
+ uint32_t l3_addr[4];
/*
- * This field represents the build version of network control
- * firmware. A change in update version represents bug fixes.
+ * The value of inner destination IP address to be used in
+ * filtering. For IPv4, first four bytes represent the IP
+ * address.
*/
- uint8_t netctrl_fw_rsvd;
+ uint32_t t_l3_addr[4];
/*
- * This field is a reserved field. This field can be used to
- * represent firmware branches or customer specific releases
- * tied to a specific (major,minor,update) version
+ * The value of tunnel destination IP address to be used in
+ * filtering. For IPv4, first four bytes represent the IP
+ * address.
*/
- uint32_t dev_caps_cfg;
+ uint8_t l3_addr_type;
/*
- * This field is used to indicate device's capabilities and
- * configurations.
+ * This value indicates the type of inner IP address. 4 - IPv4 6
+ * - IPv6 All others are invalid.
*/
+ uint8_t t_l3_addr_type;
/*
- * If set to 1, then secure firmware update behavior is
- * supported. If set to 0, then secure firmware update behavior
- * is not supported.
+ * This value indicates the type of tunnel IP address. 4 - IPv4
+ * 6 - IPv6 All others are invalid.
*/
- #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SECURE_FW_UPD_SUPPORTED \
- UINT32_C(0x1)
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Non-tunnel */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL 0x0UL
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN 0x1UL
/*
- * If set to 1, then firmware based DCBX agent is supported. If
- * set to 0, then firmware based DCBX agent capability is not
- * supported on this device.
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
*/
- #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_FW_DCBX_AGENT_SUPPORTED \
- UINT32_C(0x2)
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE 0x2UL
/*
- * If set to 1, then HWRM short command format is supported. If
- * set to 0, then HWRM short command format is not supported.
+ * Generic Routing Encapsulation (GRE) inside
+ * Ethernet payload
*/
- #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SHORT_CMD_SUPPORTED \
- UINT32_C(0x4)
- /*
- * If set to 1, then HWRM short command format is required. If
- * set to 0, then HWRM short command format is not required.
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE 0x3UL
+ /* IP in IP */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP 0x4UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE 0x5UL
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS 0x6UL
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT 0x7UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
*/
- #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SHORT_CMD_INPUTUIRED \
- UINT32_C(0x8)
- uint8_t roce_fw_maj;
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE 0x8UL
/*
- * This field represents the major version of RoCE firmware. A
- * change in major version represents a major release.
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
*/
- uint8_t roce_fw_min;
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 0x9UL
+ /* Any tunneled traffic */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL 0xffUL
+ uint8_t unused_0;
+ uint32_t vni;
/*
- * This field represents the minor version of RoCE firmware. A
- * change in minor version represents significant functionality
- * changes.
+ * Virtual Network Identifier (VNI). Only valid with
+ * tunnel_types VXLAN, NVGRE, and Geneve. Only lower 24-bits of
+ * VNI field are used in setting up the filter.
*/
- uint8_t roce_fw_bld;
+ uint32_t dst_vnic_id;
+ /* Logical VNIC ID of the destination VNIC. */
+ uint32_t mirror_vnic_id;
+ /* Logical VNIC ID of the VNIC where traffic is mirrored. */
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_cfa_tunnel_filter_alloc_output {
+ uint16_t error_code;
/*
- * This field represents the build version of RoCE firmware. A
- * change in update version represents bug fixes.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- uint8_t roce_fw_rsvd;
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * This field is a reserved field. This field can be used to
- * represent firmware branches or customer specific releases
- * tied to a specific (major,minor,update) version
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- char hwrm_fw_name[16];
+ uint64_t tunnel_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t flow_id;
/*
- * This field represents the name of HWRM FW (ASCII chars with
- * NULL at the end).
+ * This is the ID of the flow associated with this filter. This
+ * value shall be used to match and associate the flow
+ * identifier returned in completion records. A value of
+ * 0xFFFFFFFF shall indicate no flow id.
*/
- char mgmt_fw_name[16];
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
/*
- * This field represents the name of mgmt FW (ASCII chars with
- * NULL at the end).
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- char netctrl_fw_name[16];
+} __attribute__((packed));
+
+/* hwrm_cfa_tunnel_filter_free */
+/* Description: Free a tunnel filter */
+/* Input (24 bytes) */
+struct hwrm_cfa_tunnel_filter_free_input {
+ uint16_t req_type;
/*
- * This field represents the name of network control firmware
- * (ASCII chars with NULL at the end).
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- uint32_t reserved2[4];
+ uint16_t cmpl_ring;
/*
- * This field is reserved for future use. The responder should
- * set it to 0. The requester should ignore this field.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- char roce_fw_name[16];
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * This field represents the name of RoCE FW (ASCII chars with
- * NULL at the end).
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint16_t chip_num;
- /* This field returns the chip number. */
- uint8_t chip_rev;
- /* This field returns the revision of chip. */
- uint8_t chip_metal;
- /* This field returns the chip metal number. */
- uint8_t chip_bond_id;
- /* This field returns the bond id of the chip. */
- uint8_t chip_platform_type;
+ uint64_t resp_addr;
/*
- * This value indicates the type of platform used for chip
- * implementation.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- /* ASIC */
- #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_ASIC UINT32_C(0x0)
- /* FPGA platform of the chip. */
- #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_FPGA UINT32_C(0x1)
- /* Palladium platform of the chip. */
- #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_PALLADIUM UINT32_C(0x2)
- uint16_t max_req_win_len;
+ uint64_t tunnel_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_tunnel_filter_free_output {
+ uint16_t error_code;
/*
- * This field returns the maximum value of request window that
- * is supported by the HWRM. The request window is mapped into
- * device address space using MMIO.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- uint16_t max_resp_len;
- /* This field returns the maximum value of response buffer in bytes. */
- uint16_t def_req_timeout;
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * This field returns the default request timeout value in
- * milliseconds.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- uint8_t unused_0;
+ uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -2134,22 +19925,14 @@ struct hwrm_ver_get_output {
*/
} __attribute__((packed));
-/* hwrm_func_reset */
-/*
- * Description: This command resets a hardware function (PCIe function) and
- * frees any resources used by the function. This command shall be initiated by
- * the driver after an FLR has occurred to prepare the function for re-use. This
- * command may also be initiated by a driver prior to doing it's own
- * configuration. This command puts the function into the reset state. In the
- * reset state, global and port related features of the chip are not available.
- */
+/* hwrm_cfa_redirect_tunnel_type_alloc */
/*
- * Note: This command will reset a function that has already been disabled or
- * idled. The command returns all the resources owned by the function so a new
- * driver may allocate and configure resources normally.
+ * Description: This is a filter that uses tunnel type to redirect the flows to
+ * specified function. This is specific to RX side only. Based on the SVIF and
+ * tunnel type, the traffic is redirected.
*/
-/* Input (24 bytes) */
-struct hwrm_func_reset_input {
+/* Input (24 bytes) */
+struct hwrm_cfa_redirect_tunnel_type_alloc_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -2176,49 +19959,59 @@ struct hwrm_func_reset_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t enables;
- /* This bit must be '1' for the vf_id_valid field to be configured. */
- #define HWRM_FUNC_RESET_INPUT_ENABLES_VF_ID_VALID UINT32_C(0x1)
- uint16_t vf_id;
+ uint16_t dest_fid;
+ /* The destination function id, to whom the traffic is redirected. */
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Non-tunnel */
+ #define \
+ HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ 0x0UL
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ 0x1UL
/*
- * The ID of the VF that this PF is trying to reset. Only the
- * parent PF shall be allowed to reset a child VF. A parent PF
- * driver shall use this field only when a specific child VF is
- * requested to be reset.
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
*/
- uint8_t func_reset_level;
- /* This value indicates the level of a function reset. */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ 0x2UL
/*
- * Reset the caller function and its children
- * VFs (if any). If no children functions exist,
- * then reset the caller function only.
+ * Generic Routing Encapsulation (GRE) inside
+ * Ethernet payload
*/
- #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETALL UINT32_C(0x0)
- /* Reset the caller function only */
- #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETME UINT32_C(0x1)
- /*
- * Reset all children VFs of the caller function
- * driver if the caller is a PF driver. It is an
- * error to specify this level by a VF driver.
- * It is an error to specify this level by a PF
- * driver with no children VFs.
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ 0x3UL
+ /* IP in IP */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPIP 0x4UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ 0x5UL
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_MPLS 0x6UL
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_STT 0x7UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
*/
- #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETCHILDREN \
- UINT32_C(0x2)
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ 0x8UL
/*
- * Reset a specific VF of the caller function
- * driver if the caller is the parent PF driver.
- * It is an error to specify this level by a VF
- * driver. It is an error to specify this level
- * by a PF driver that is not the parent of the
- * VF that is being requested to reset.
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
*/
- #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETVF UINT32_C(0x3)
- uint8_t unused_0;
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ 0x9UL
+ /* Any tunneled traffic */
+ #define \
+ HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ 0xffUL
+ uint8_t unused_0[5];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_func_reset_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_redirect_tunnel_type_alloc_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -2249,16 +20042,12 @@ struct hwrm_func_reset_output {
*/
} __attribute__((packed));
-/* hwrm_func_qcaps */
+/* hwrm_cfa_redirect_tunnel_type_free */
/*
- * Description: This command returns capabilities of a function. The input FID
- * value is used to indicate what function is being queried. This allows a
- * physical function driver to query virtual functions that are children of the
- * physical function. The output FID value is needed to configure Rings and
- * MSI-X vectors so their DMA operations appear correctly on the PCI bus.
+ * Description: Free the filter that redirects the flows based on tunnel type.
*/
-/* Input (24 bytes) */
-struct hwrm_func_qcaps_input {
+/* Input (24 bytes) */
+struct hwrm_cfa_redirect_tunnel_type_free_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -2285,16 +20074,53 @@ struct hwrm_func_qcaps_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t fid;
+ uint16_t dest_fid;
+ /* The destination function id, to whom the traffic is redirected. */
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Non-tunnel */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ 0x0UL
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_VXLAN 0x1UL
/*
- * Function ID of the function that is being queried. 0xFF...
- * (All Fs) if the query is for the requesting function.
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
*/
- uint16_t unused_0[3];
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_NVGRE 0x2UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside
+ * Ethernet payload
+ */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_L2GRE 0x3UL
+ /* IP in IP */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPIP 0x4UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_GENEVE \
+ 0x5UL
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_MPLS 0x6UL
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_STT 0x7UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
+ */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPGRE 0x8UL
+ /*
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
+ */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ 0x9UL
+ /* Any tunneled traffic */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ 0xffUL
+ uint8_t unused_0[5];
} __attribute__((packed));
-/* Output (80 bytes) */
-struct hwrm_func_qcaps_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_redirect_tunnel_type_free_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -2310,203 +20136,116 @@ struct hwrm_func_qcaps_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint16_t fid;
- /*
- * FID value. This value is used to identify operations on the
- * PCI bus as belonging to a particular PCI function.
- */
- uint16_t port_id;
- /*
- * Port ID of port that this function is associated with. Valid
- * only for the PF. 0xFF... (All Fs) if this function is not
- * associated with any port. 0xFF... (All Fs) if this function
- * is called from a VF.
- */
- uint32_t flags;
- /* If 1, then Push mode is supported on this function. */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PUSH_MODE_SUPPORTED UINT32_C(0x1)
- /*
- * If 1, then the global MSI-X auto-masking is enabled for the
- * device.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_GLOBAL_MSIX_AUTOMASKING \
- UINT32_C(0x2)
- /*
- * If 1, then the Precision Time Protocol (PTP) processing is
- * supported on this function. The HWRM should enable PTP on
- * only a single Physical Function (PF) per port.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PTP_SUPPORTED UINT32_C(0x4)
- /*
- * If 1, then RDMA over Converged Ethernet (RoCE) v1 is
- * supported on this function.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ROCE_V1_SUPPORTED UINT32_C(0x8)
- /*
- * If 1, then RDMA over Converged Ethernet (RoCE) v2 is
- * supported on this function.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ROCE_V2_SUPPORTED UINT32_C(0x10)
- /*
- * If 1, then control and configuration of WoL magic packet are
- * supported on this function.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_WOL_MAGICPKT_SUPPORTED \
- UINT32_C(0x20)
- /*
- * If 1, then control and configuration of bitmap pattern packet
- * are supported on this function.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_WOL_BMP_SUPPORTED UINT32_C(0x40)
- /*
- * If set to 1, then the control and configuration of rate limit
- * of an allocated TX ring on the queried function is supported.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_TX_RING_RL_SUPPORTED UINT32_C(0x80)
- /*
- * If 1, then control and configuration of minimum and maximum
- * bandwidths are supported on the queried function.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_TX_BW_CFG_SUPPORTED UINT32_C(0x100)
- /*
- * If the query is for a VF, then this flag shall be ignored. If
- * this query is for a PF and this flag is set to 1, then the PF
- * has the capability to set the rate limits on the TX rings of
- * its children VFs. If this query is for a PF and this flag is
- * set to 0, then the PF does not have the capability to set the
- * rate limits on the TX rings of its children VFs.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_VF_TX_RING_RL_SUPPORTED \
- UINT32_C(0x200)
- /*
- * If the query is for a VF, then this flag shall be ignored. If
- * this query is for a PF and this flag is set to 1, then the PF
- * has the capability to set the minimum and/or maximum
- * bandwidths for its children VFs. If this query is for a PF
- * and this flag is set to 0, then the PF does not have the
- * capability to set the minimum or maximum bandwidths for its
- * children VFs.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_VF_BW_CFG_SUPPORTED UINT32_C(0x400)
- /*
- * Standard TX Ring mode is used for the allocation of TX ring
- * and underlying scheduling resources that allow bandwidth
- * reservation and limit settings on the queried function. If
- * set to 1, then standard TX ring mode is supported on the
- * queried function. If set to 0, then standard TX ring mode is
- * not available on the queried function.
- */
- #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_STD_TX_RING_MODE_SUPPORTED \
- UINT32_C(0x800)
- uint8_t mac_address[6];
- /*
- * This value is current MAC address configured for this
- * function. A value of 00-00-00-00-00-00 indicates no MAC
- * address is currently configured.
- */
- uint16_t max_rsscos_ctx;
- /*
- * The maximum number of RSS/COS contexts that can be allocated
- * to the function.
- */
- uint16_t max_cmpl_rings;
- /*
- * The maximum number of completion rings that can be allocated
- * to the function.
- */
- uint16_t max_tx_rings;
- /*
- * The maximum number of transmit rings that can be allocated to
- * the function.
- */
- uint16_t max_rx_rings;
- /*
- * The maximum number of receive rings that can be allocated to
- * the function.
- */
- uint16_t max_l2_ctxs;
- /*
- * The maximum number of L2 contexts that can be allocated to
- * the function.
- */
- uint16_t max_vnics;
- /*
- * The maximum number of VNICs that can be allocated to the
- * function.
- */
- uint16_t first_vf_id;
- /*
- * The identifier for the first VF enabled on a PF. This is
- * valid only on the PF with SR-IOV enabled. 0xFF... (All Fs) if
- * this command is called on a PF with SR-IOV disabled or on a
- * VF.
- */
- uint16_t max_vfs;
- /*
- * The maximum number of VFs that can be allocated to the
- * function. This is valid only on the PF with SR-IOV enabled.
- * 0xFF... (All Fs) if this command is called on a PF with SR-
- * IOV disabled or on a VF.
- */
- uint16_t max_stat_ctx;
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
/*
- * The maximum number of statistic contexts that can be
- * allocated to the function.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- uint32_t max_encap_records;
+} __attribute__((packed));
+
+/* hwrm_cfa_encap_record_alloc */
+/*
+ * Description: This command is used to create an encapsulation record. The
+ * source MAC address and source IP address specified for the source property
+ * checks shall be used in the encapsulation where applicable.
+ */
+/* Input (32 bytes) */
+struct hwrm_cfa_encap_record_alloc_input {
+ uint16_t req_type;
/*
- * The maximum number of Encapsulation records that can be
- * offloaded by this function.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- uint32_t max_decap_records;
+ uint16_t cmpl_ring;
/*
- * The maximum number of decapsulation records that can be
- * offloaded by this function.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- uint32_t max_tx_em_flows;
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * The maximum number of Exact Match (EM) flows that can be
- * offloaded by this function on the TX side.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint32_t max_tx_wm_flows;
+ uint64_t resp_addr;
/*
- * The maximum number of Wildcard Match (WM) flows that can be
- * offloaded by this function on the TX side.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint32_t max_rx_em_flows;
+ uint32_t flags;
/*
- * The maximum number of Exact Match (EM) flows that can be
- * offloaded by this function on the RX side.
+ * Setting of this flag indicates the applicability to the
+ * loopback path.
*/
- uint32_t max_rx_wm_flows;
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_FLAGS_LOOPBACK 0x1UL
+ uint8_t encap_type;
+ /* Encapsulation Type. */
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VXLAN 0x1UL
/*
- * The maximum number of Wildcard Match (WM) flows that can be
- * offloaded by this function on the RX side.
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
*/
- uint32_t max_mcast_filters;
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_NVGRE 0x2UL
/*
- * The maximum number of multicast filters that can be supported
- * by this function on the RX side.
+ * Generic Routing Encapsulation (GRE) after
+ * inside Ethernet payload
*/
- uint32_t max_flow_id;
- /*
- * The maximum value of flow_id that can be supported in
- * completion records.
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_L2GRE 0x3UL
+ /* IP in IP */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_IPIP 0x4UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_GENEVE 0x5UL
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_MPLS 0x6UL
+ /* VLAN */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VLAN 0x7UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
*/
- uint32_t max_hw_ring_grps;
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_IPGRE 0x8UL
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint32_t encap_data[20];
+ /* This value is encap data used for the given encap type. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_encap_record_alloc_output {
+ uint16_t error_code;
/*
- * The maximum number of HW ring groups that can be supported on
- * this function.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- uint16_t max_sp_tx_rings;
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * The maximum number of strict priority transmit rings that can
- * be allocated to the function. This number indicates the
- * maximum number of TX rings that can be assigned strict
- * priorities out of the maximum number of TX rings that can be
- * allocated (max_tx_rings) to the function.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
+ uint32_t encap_record_id;
+ /* This value is an opaque id into CFA data structures. */
uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -2518,21 +20257,10 @@ struct hwrm_func_qcaps_output {
*/
} __attribute__((packed));
-/* hwrm_func_qcfg */
-/*
- * Description: This command returns the current configuration of a function.
- * The input FID value is used to indicate what function is being queried. This
- * allows a physical function driver to query virtual functions that are
- * children of the physical function. The output FID value is needed to
- * configure Rings and MSI-X vectors so their DMA operations appear correctly on
- * the PCI bus. This command should be called by every driver after
- * 'hwrm_func_cfg' to get the actual number of resources allocated by the HWRM.
- * The values returned by hwrm_func_qcfg are the values the driver shall use.
- * These values may be different than what was originally requested in the
- * 'hwrm_func_cfg' command.
- */
-/* Input (24 bytes) */
-struct hwrm_func_qcfg_input {
+/* hwrm_cfa_encap_record_free */
+/* Description: Free an encap record */
+/* Input (24 bytes) */
+struct hwrm_cfa_encap_record_free_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -2559,16 +20287,13 @@ struct hwrm_func_qcfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t fid;
- /*
- * Function ID of the function that is being queried. 0xFF...
- * (All Fs) if the query is for the requesting function.
- */
- uint16_t unused_0[3];
+ uint32_t encap_record_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t unused_0;
} __attribute__((packed));
-/* Output (72 bytes) */
-struct hwrm_func_qcfg_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_encap_record_free_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -2584,328 +20309,284 @@ struct hwrm_func_qcfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint16_t fid;
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
/*
- * FID value. This value is used to identify operations on the
- * PCI bus as belonging to a particular PCI function.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- uint16_t port_id;
+} __attribute__((packed));
+
+/* hwrm_cfa_ntuple_filter_alloc */
+/*
+ * Description: This is a ntuple filter that uses fields from L4/L3 header and
+ * optionally fields from L2. The ntuple filters apply to receive traffic only.
+ * All L2/L3/L4 header fields are specified in network byte order. These filters
+ * can be used for Receive Flow Steering (RFS). # For ethertype value, only
+ * 0x0800 (IPv4) and 0x86dd (IPv6) shall be supported for ntuple filters. # If a
+ * field specified in this command is not enabled as a valid field, then that
+ * field shall not be used in matching packet header fields against this filter.
+ */
+/* Input (128 bytes) */
+struct hwrm_cfa_ntuple_filter_alloc_input {
+ uint16_t req_type;
/*
- * Port ID of port that this function is associated with.
- * 0xFF... (All Fs) if this function is not associated with any
- * port.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- uint16_t vlan;
+ uint16_t cmpl_ring;
/*
- * This value is the current VLAN setting for this function. The
- * value of 0 for this field indicates no priority tagging or
- * VLAN is used. This field's format is same as 802.1Q Tag's Tag
- * Control Information (TCI) format that includes both Priority
- * Code Point (PCP) and VLAN Identifier (VID).
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- uint16_t flags;
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * If 1, then magic packet based Out-Of-Box WoL is enabled on
- * the port associated with this function.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_OOB_WOL_MAGICPKT_ENABLED \
- UINT32_C(0x1)
+ uint64_t resp_addr;
/*
- * If 1, then bitmap pattern based Out-Of-Box WoL packet is
- * enabled on the port associated with this function.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_OOB_WOL_BMP_ENABLED UINT32_C(0x2)
+ uint32_t flags;
/*
- * If set to 1, then FW based DCBX agent is enabled and running
- * on the port associated with this function. If set to 0, then
- * DCBX agent is not running in the firmware.
+ * Setting of this flag indicates the applicability to the
+ * loopback path.
*/
- #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_FW_DCBX_AGENT_ENABLED \
- UINT32_C(0x4)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK 0x1UL
/*
- * Standard TX Ring mode is used for the allocation of TX ring
- * and underlying scheduling resources that allow bandwidth
- * reservation and limit settings on the queried function. If
- * set to 1, then standard TX ring mode is enabled on the
- * queried function. If set to 0, then the standard TX ring mode
- * is disabled on the queried function. In this extended TX ring
- * resource mode, the minimum and maximum bandwidth settings are
- * not supported to allow the allocation of TX rings to span
- * multiple scheduler nodes.
+ * Setting of this flag indicates drop action. If this flag is
+ * not set, then it should be considered accept action.
*/
- #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_STD_TX_RING_MODE_ENABLED \
- UINT32_C(0x8)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_DROP 0x2UL
/*
- * If set to 1 then FW based LLDP agent is enabled and running
- * on the port associated with this function. If set to 0 then
- * the LLDP agent is not running in the firmware.
+ * Setting of this flag indicates that a meter is expected to be
+ * attached to this flow. This hint can be used when choosing
+ * the action record format required for the flow.
*/
- #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_FW_LLDP_AGENT_ENABLED UINT32_C(0x10)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_METER 0x4UL
+ uint32_t enables;
+ /* This bit must be '1' for the l2_filter_id field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_L2_FILTER_ID 0x1UL
+ /* This bit must be '1' for the ethertype field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_ETHERTYPE 0x2UL
+ /* This bit must be '1' for the tunnel_type field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE 0x4UL
+ /* This bit must be '1' for the src_macaddr field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_MACADDR 0x8UL
+ /* This bit must be '1' for the ipaddr_type field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_IPADDR_TYPE 0x10UL
+ /* This bit must be '1' for the src_ipaddr field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR 0x20UL
/*
- * If set to 1, then multi-host mode is active for this
- * function. If set to 0, then multi-host mode is inactive for
- * this function or not applicable for this device.
+ * This bit must be '1' for the src_ipaddr_mask field to be
+ * configured.
*/
- #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_MULTI_HOST UINT32_C(0x20)
- uint8_t mac_address[6];
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR_MASK \
+ 0x40UL
+ /* This bit must be '1' for the dst_ipaddr field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR 0x80UL
/*
- * This value is current MAC address configured for this
- * function. A value of 00-00-00-00-00-00 indicates no MAC
- * address is currently configured.
+ * This bit must be '1' for the dst_ipaddr_mask field to be
+ * configured.
*/
- uint16_t pci_id;
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR_MASK \
+ 0x100UL
+ /* This bit must be '1' for the ip_protocol field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_IP_PROTOCOL 0x200UL
+ /* This bit must be '1' for the src_port field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT 0x400UL
/*
- * This value is current PCI ID of this function. If ARI is
- * enabled, then it is Bus Number (8b):Function Number(8b).
- * Otherwise, it is Bus Number (8b):Device Number (4b):Function
- * Number(4b).
+ * This bit must be '1' for the src_port_mask field to be
+ * configured.
*/
- uint16_t alloc_rsscos_ctx;
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT_MASK 0x800UL
+ /* This bit must be '1' for the dst_port field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_PORT 0x1000UL
/*
- * The number of RSS/COS contexts currently allocated to the
- * function.
+ * This bit must be '1' for the dst_port_mask field to be
+ * configured.
*/
- uint16_t alloc_cmpl_rings;
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_PORT_MASK \
+ 0x2000UL
+ /* This bit must be '1' for the pri_hint field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_PRI_HINT 0x4000UL
/*
- * The number of completion rings currently allocated to the
- * function. This does not include the rings allocated to any
- * children functions if any.
+ * This bit must be '1' for the ntuple_filter_id field to be
+ * configured.
*/
- uint16_t alloc_tx_rings;
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_NTUPLE_FILTER_ID \
+ 0x8000UL
+ /* This bit must be '1' for the dst_id field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_ID 0x10000UL
/*
- * The number of transmit rings currently allocated to the
- * function. This does not include the rings allocated to any
- * children functions if any.
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
*/
- uint16_t alloc_rx_rings;
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ 0x20000UL
+ /* This bit must be '1' for the dst_macaddr field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_MACADDR 0x40000UL
+ uint64_t l2_filter_id;
/*
- * The number of receive rings currently allocated to the
- * function. This does not include the rings allocated to any
- * children functions if any.
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
*/
- uint16_t alloc_l2_ctx;
- /* The allocated number of L2 contexts to the function. */
- uint16_t alloc_vnics;
- /* The allocated number of vnics to the function. */
- uint16_t mtu;
+ uint8_t src_macaddr[6];
/*
- * The maximum transmission unit of the function. For rings
- * allocated on this function, this default value is used if
- * ring MTU is not specified.
+ * This value indicates the source MAC address in the Ethernet
+ * header.
*/
- uint16_t mru;
+ uint16_t ethertype;
+ /* This value indicates the ethertype in the Ethernet header. */
+ uint8_t ip_addr_type;
/*
- * The maximum receive unit of the function. For vnics allocated
- * on this function, this default value is used if vnic MRU is
- * not specified.
+ * This value indicates the type of IP address. 4 - IPv4 6 -
+ * IPv6 All others are invalid.
*/
- uint16_t stat_ctx_id;
- /* The statistics context assigned to a function. */
- uint8_t port_partition_type;
+ /* invalid */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN 0x0UL
+ /* IPv4 */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 0x4UL
+ /* IPv6 */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 0x6UL
+ uint8_t ip_protocol;
+ /*
+ * The value of protocol filed in IP header. Applies to UDP and
+ * TCP traffic. 6 - TCP 17 - UDP
+ */
+ /* invalid */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN 0x0UL
+ /* TCP */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_TCP 0x6UL
+ /* UDP */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP 0x11UL
+ uint16_t dst_id;
/*
- * The HWRM shall return Unknown value for this field when this
- * command is used to query VF's configuration.
+ * If set, this value shall represent the Logical VNIC ID of the
+ * destination VNIC for the RX path and network port id of the
+ * destination port for the TX path.
*/
- /* Single physical function */
- #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_SPF UINT32_C(0x0)
- /* Multiple physical functions */
- #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_MPFS UINT32_C(0x1)
- /* Network Partitioning 1.0 */
- #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR1_0 UINT32_C(0x2)
- /* Network Partitioning 1.5 */
- #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR1_5 UINT32_C(0x3)
- /* Network Partitioning 2.0 */
- #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR2_0 UINT32_C(0x4)
- /* Unknown */
- #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_UNKNOWN UINT32_C(0xff)
- uint8_t port_pf_cnt;
+ uint16_t mirror_vnic_id;
+ /* Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint8_t tunnel_type;
/*
- * This field will indicate number of physical functions on this
- * port_partition. HWRM shall return unavail (i.e. value of 0)
- * for this field when this command is used to query VF's
- * configuration or from older firmware that doesn't support
- * this field.
+ * This value indicates the tunnel type for this filter. If this
+ * field is not specified, then the filter shall apply to both
+ * non-tunneled and tunneled packets. If this field conflicts
+ * with the tunnel_type specified in the l2_filter_id, then the
+ * HWRM shall return an error for this command.
*/
- /* number of PFs is not available */
- #define HWRM_FUNC_QCFG_OUTPUT_PORT_PF_CNT_UNAVAIL UINT32_C(0x0)
- uint16_t dflt_vnic_id;
- /* The default VNIC ID assigned to a function that is being queried. */
- uint8_t unused_0;
- uint8_t unused_1;
- uint32_t min_bw;
+ /* Non-tunnel */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL 0x0UL
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN 0x1UL
/*
- * Minimum BW allocated for this function. The HWRM will
- * translate this value into byte counter and time interval used
- * for the scheduler inside the device. A value of 0 indicates
- * the minimum bandwidth is not configured.
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
*/
- /* The bandwidth value. */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_SFT 0
- /* The granularity of the value (bits or bytes). */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE UINT32_C(0x10000000)
- /* Value is in bits. */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BITS (UINT32_C(0x0) << 28)
- /* Value is in bytes. */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BYTES \
- (UINT32_C(0x1) << 28)
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_LAST \
- FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BYTES
- /* bw_value_unit is 3 b */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_MASK \
- UINT32_C(0xe0000000)
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_SFT 29
- /* Value is in Mb or MB (base 10). */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_MEGA \
- (UINT32_C(0x0) << 29)
- /* Value is in Kb or KB (base 10). */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_KILO \
- (UINT32_C(0x2) << 29)
- /* Value is in bits or bytes. */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_BASE \
- (UINT32_C(0x4) << 29)
- /* Value is in Gb or GB (base 10). */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_GIGA \
- (UINT32_C(0x6) << 29)
- /* Value is in 1/100th of a percentage of total bandwidth. */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
- (UINT32_C(0x1) << 29)
- /* Invalid unit */
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_INVALID \
- (UINT32_C(0x7) << 29)
- #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_LAST \
- FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_INVALID
- uint32_t max_bw;
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE 0x2UL
/*
- * Maximum BW allocated for this function. The HWRM will
- * translate this value into byte counter and time interval used
- * for the scheduler inside the device. A value of 0 indicates
- * that the maximum bandwidth is not configured.
+ * Generic Routing Encapsulation (GRE) inside
+ * Ethernet payload
*/
- /* The bandwidth value. */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_SFT 0
- /* The granularity of the value (bits or bytes). */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE UINT32_C(0x10000000)
- /* Value is in bits. */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BITS (UINT32_C(0x0) << 28)
- /* Value is in bytes. */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BYTES \
- (UINT32_C(0x1) << 28)
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_LAST \
- FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BYTES
- /* bw_value_unit is 3 b */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_MASK \
- UINT32_C(0xe0000000)
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
- /* Value is in Mb or MB (base 10). */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
- (UINT32_C(0x0) << 29)
- /* Value is in Kb or KB (base 10). */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_KILO \
- (UINT32_C(0x2) << 29)
- /* Value is in bits or bytes. */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_BASE \
- (UINT32_C(0x4) << 29)
- /* Value is in Gb or GB (base 10). */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
- (UINT32_C(0x6) << 29)
- /* Value is in 1/100th of a percentage of total bandwidth. */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
- (UINT32_C(0x1) << 29)
- /* Invalid unit */
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
- (UINT32_C(0x7) << 29)
- #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_LAST \
- FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_INVALID
- uint8_t evb_mode;
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE 0x3UL
+ /* IP in IP */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP 0x4UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE 0x5UL
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS 0x6UL
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT 0x7UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE 0x8UL
/*
- * This value indicates the Edge virtual bridge mode for the
- * domain that this function belongs to.
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
*/
- /* No Edge Virtual Bridging (EVB) */
- #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_NO_EVB UINT32_C(0x0)
- /* Virtual Ethernet Bridge (VEB) */
- #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEB UINT32_C(0x1)
- /* Virtual Ethernet Port Aggregator (VEPA) */
- #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEPA UINT32_C(0x2)
- uint8_t unused_2;
- uint16_t alloc_vfs;
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 0x9UL
+ /* Any tunneled traffic */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL 0xffUL
+ uint8_t pri_hint;
/*
- * The number of VFs that are allocated to the function. This is
- * valid only on the PF with SR-IOV enabled. 0xFF... (All Fs) if
- * this command is called on a PF with SR-IOV disabled or on a
- * VF.
+ * This hint is provided to help in placing the filter in the
+ * filter table.
*/
- uint32_t alloc_mcast_filters;
+ /* No preference */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER 0x0UL
+ /* Above the given filter */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE 0x1UL
+ /* Below the given filter */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_BELOW 0x2UL
+ /* As high as possible */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_HIGHEST 0x3UL
+ /* As low as possible */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_LOWEST 0x4UL
+ uint32_t src_ipaddr[4];
/*
- * The number of allocated multicast filters for this function
- * on the RX side.
+ * The value of source IP address to be used in filtering. For
+ * IPv4, first four bytes represent the IP address.
*/
- uint32_t alloc_hw_ring_grps;
- /* The number of allocated HW ring groups for this function. */
- uint16_t alloc_sp_tx_rings;
+ uint32_t src_ipaddr_mask[4];
/*
- * The number of strict priority transmit rings out of currently
- * allocated TX rings to the function (alloc_tx_rings).
+ * The value of source IP address mask to be used in filtering.
+ * For IPv4, first four bytes represent the IP address mask.
*/
- uint8_t unused_3;
- uint8_t valid;
+ uint32_t dst_ipaddr[4];
/*
- * This field is used in Output records to indicate that the
- * output is completely written to RAM. This field should be
- * read as '1' to indicate that the output has been completely
- * written. When writing a command completion or response to an
- * internal processor, the order of writes has to be such that
- * this field is written last.
+ * The value of destination IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
*/
-} __attribute__((packed));
-
-/* hwrm_func_vlan_qcfg */
-/*
- * Description: This command should be called by PF driver to get the current
- * C-TAG, S-TAG and correcponsing PCP and TPID values configured for the
- * function.
- */
-/* Input (24 bytes) */
-struct hwrm_func_vlan_qcfg_input {
- uint16_t req_type;
+ uint32_t dst_ipaddr_mask[4];
/*
- * This value indicates what type of request this is. The format
- * for the rest of the command is determined by this field.
+ * The value of destination IP address mask to be used in
+ * filtering. For IPv4, first four bytes represent the IP
+ * address mask.
*/
- uint16_t cmpl_ring;
+ uint16_t src_port;
/*
- * This value indicates the what completion ring the request
- * will be optionally completed on. If the value is -1, then no
- * CR completion will be generated. Any other value must be a
- * valid CR ring_id value for this function.
+ * The value of source port to be used in filtering. Applies to
+ * UDP and TCP traffic.
*/
- uint16_t seq_id;
- /* This value indicates the command sequence number. */
- uint16_t target_id;
+ uint16_t src_port_mask;
/*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function
- * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
- * - HWRM
+ * The value of source port mask to be used in filtering.
+ * Applies to UDP and TCP traffic.
*/
- uint64_t resp_addr;
+ uint16_t dst_port;
/*
- * This is the host address where the response will be written
- * when the request is complete. This area must be 16B aligned
- * and must be cleared to zero before the request is made.
+ * The value of destination port to be used in filtering.
+ * Applies to UDP and TCP traffic.
*/
- uint16_t fid;
+ uint16_t dst_port_mask;
/*
- * Function ID of the function that is being configured. If set
- * to 0xFF... (All Fs), then the configuration is for the
- * requesting function.
+ * The value of destination port mask to be used in filtering.
+ * Applies to UDP and TCP traffic.
*/
- uint16_t unused_0[3];
-};
+ uint64_t ntuple_filter_id_hint;
+ /* This is the ID of the filter that goes along with the pri_hint. */
+} __attribute__((packed));
-/* Output (40 bytes) */
-struct hwrm_func_vlan_qcfg_output {
+/* Output (24 bytes) */
+struct hwrm_cfa_ntuple_filter_alloc_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -2921,10 +20602,18 @@ struct hwrm_func_vlan_qcfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t unused_0;
+ uint64_t ntuple_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t flow_id;
+ /*
+ * This is the ID of the flow associated with this filter. This
+ * value shall be used to match and associate the flow
+ * identifier returned in completion records. A value of
+ * 0xFFFFFFFF shall indicate no flow id.
+ */
+ uint8_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
- uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -2934,40 +20623,31 @@ struct hwrm_func_vlan_qcfg_output {
* internal processor, the order of writes has to be such that
* this field is written last.
*/
- uint16_t stag_vid;
- /* S-TAG VLAN identifier configured for the function. */
- uint8_t stag_pcp;
- /* S-TAG PCP value configured for the function. */
- uint8_t unused_4;
- uint16_t stag_tpid;
+} __attribute__((packed));
+
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_cfa_ntuple_filter_alloc_cmd_err {
+ uint8_t code;
/*
- * S-TAG TPID value configured for the function. This field is
- * specified in network byte order.
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
*/
- uint16_t ctag_vid;
- /* C-TAG VLAN identifier configured for the function. */
- uint8_t ctag_pcp;
- /* C-TAG PCP value configured for the function. */
- uint8_t unused_5;
- uint16_t ctag_tpid;
+ /* Unknown error */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_UNKNOWN 0x0UL
/*
- * C-TAG TPID value configured for the function. This field is
- * specified in network byte order.
+ * Unable to complete operation due to conflict
+ * with Rx Mask VLAN
*/
- uint32_t rsvd2;
- /* Future use. */
- uint32_t rsvd3;
- /* Future use. */
- uint32_t unused_6;
-};
+ #define \
+ HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_RX_MASK_VLAN_CONFLICT_ERR \
+ 0x1UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
-/* hwrm_func_vlan_cfg */
-/*
- * Description: This command allows PF driver to configure C-TAG, S-TAG and
- * corresponding PCP and TPID values for a function.
- */
-/* Input (48 bytes) */
-struct hwrm_func_vlan_cfg_input {
+/* hwrm_cfa_ntuple_filter_free */
+/* Description: Free an ntuple filter */
+/* Input (24 bytes) */
+struct hwrm_cfa_ntuple_filter_free_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -2984,66 +20664,22 @@ struct hwrm_func_vlan_cfg_input {
/* This value indicates the command sequence number. */
uint16_t target_id;
/*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function
- * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
- * - HWRM
- */
- uint64_t resp_addr;
- /*
- * This is the host address where the response will be written
- * when the request is complete. This area must be 16B aligned
- * and must be cleared to zero before the request is made.
- */
- uint16_t fid;
- /*
- * Function ID of the function that is being configured. If set
- * to 0xFF... (All Fs), then the configuration is for the
- * requesting function.
- */
- uint8_t unused_0;
- uint8_t unused_1;
- uint32_t enables;
- /* This bit must be '1' for the stag_vid field to be configured. */
- #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_VID UINT32_C(0x1)
- /* This bit must be '1' for the ctag_vid field to be configured. */
- #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_VID UINT32_C(0x2)
- /* This bit must be '1' for the stag_pcp field to be configured. */
- #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_PCP UINT32_C(0x4)
- /* This bit must be '1' for the ctag_pcp field to be configured. */
- #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_PCP UINT32_C(0x8)
- /* This bit must be '1' for the stag_tpid field to be configured. */
- #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_TPID UINT32_C(0x10)
- /* This bit must be '1' for the ctag_tpid field to be configured. */
- #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_TPID UINT32_C(0x20)
- uint16_t stag_vid;
- /* S-TAG VLAN identifier configured for the function. */
- uint8_t stag_pcp;
- /* S-TAG PCP value configured for the function. */
- uint8_t unused_2;
- uint16_t stag_tpid;
- /*
- * S-TAG TPID value configured for the function. This field is
- * specified in network byte order.
- */
- uint16_t ctag_vid;
- /* C-TAG VLAN identifier configured for the function. */
- uint8_t ctag_pcp;
- /* C-TAG PCP value configured for the function. */
- uint8_t unused_3;
- uint16_t ctag_tpid;
- /*
- * C-TAG TPID value configured for the function. This field is
- * specified in network byte order.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint32_t rsvd1;
- /* Future use. */
- uint32_t rsvd2;
- /* Future use. */
- uint32_t unused_4;
-};
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint64_t ntuple_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+} __attribute__((packed));
/* Output (16 bytes) */
-struct hwrm_func_vlan_cfg_output {
+struct hwrm_cfa_ntuple_filter_free_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -3072,45 +20708,15 @@ struct hwrm_func_vlan_cfg_output {
* internal processor, the order of writes has to be such that
* this field is written last.
*/
-};
+} __attribute__((packed));
-/* hwrm_func_cfg */
+/* hwrm_cfa_ntuple_filter_cfg */
/*
- * Description: This command allows configuration of a PF by the corresponding
- * PF driver. This command also allows configuration of a child VF by its parent
- * PF driver. The input FID value is used to indicate what function is being
- * configured. This allows a PF driver to configure the PF owned by itself or a
- * virtual function that is a child of the PF. This command allows to reserve
- * resources for a VF by its parent PF. To reverse the process, the command
- * should be called with all enables flags cleared for resources. This will free
- * allocated resources for the VF and return them to the resource pool. If this
- * command is requested by a VF driver to configure or reserve resources, then
- * the HWRM shall fail this command. If default MAC address and/or VLAN are
- * provided in this command, then the HWRM shall set up appropriate MAC/VLAN
- * filters for the function that is being configured. If source properties
- * checks are enabled and default MAC address and/or IP address are provided in
- * this command, then the HWRM shall set appropriate source property checks
- * based on provided MAC and/or IP addresses. The parent PF driver should not
- * set MTU/MRU for a VF using this command. This is to allow MTU/MRU setting by
- * the VF driver. If the MTU or MRU for a VF is set by the PF driver, then the
- * HWRM should ignore it. A function's MTU/MRU should be set prior to allocating
- * RX VNICs or TX rings. A PF driver calls hwrm_func_cfg to allocate resources
- * for itself or its children VFs. All function drivers shall call hwrm_func_cfg
- * to reserve resources. A request to hwrm_func_cfg may not be fully granted;
- * that is, a request for resources may be larger than what can be supported by
- * the device and the HWRM will allocate the best set of resources available,
- * but that may be less than requested. If all the amounts requested could not
- * be fulfilled, the HWRM shall allocate what it could and return a status code
- * of success. A function driver should call hwrm_func_qcfg immediately after
- * hwrm_func_cfg to determine what resources were assigned to the configured
- * function. A call by a PF driver to hwrm_func_cfg to allocate resources for
- * itself shall only allocate resources for the PF driver to use, not for its
- * children VFs. Likewise, a call to hwrm_func_qcfg shall return the resources
- * available for the PF driver to use, not what is available to its children
- * VFs.
+ * Description: Configure an ntuple filter with a new destination VNIC and/or
+ * meter.
*/
-/* Input (88 bytes) */
-struct hwrm_func_cfg_input {
+/* Input (48 bytes) */
+struct hwrm_cfa_ntuple_filter_cfg_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -3124,365 +20730,62 @@ struct hwrm_func_cfg_input {
* valid CR ring_id value for this function.
*/
uint16_t seq_id;
- /* This value indicates the command sequence number. */
- uint16_t target_id;
- /*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function
- * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
- * - HWRM
- */
- uint64_t resp_addr;
- /*
- * This is the host address where the response will be written
- * when the request is complete. This area must be 16B aligned
- * and must be cleared to zero before the request is made.
- */
- uint16_t fid;
- /*
- * Function ID of the function that is being configured. If set
- * to 0xFF... (All Fs), then the the configuration is for the
- * requesting function.
- */
- uint8_t unused_0;
- uint8_t unused_1;
- uint32_t flags;
- /*
- * When this bit is '1', the function is disabled with source
- * MAC address check. This is an anti-spoofing check. If this
- * flag is set, then the function shall be configured to
- * disallow transmission of frames with the source MAC address
- * that is configured for this function.
- */
- #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_DISABLE \
- UINT32_C(0x1)
- /*
- * When this bit is '1', the function is enabled with source MAC
- * address check. This is an anti-spoofing check. If this flag
- * is set, then the function shall be configured to allow
- * transmission of frames with the source MAC address that is
- * configured for this function.
- */
- #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_ENABLE \
- UINT32_C(0x2)
- /* reserved */
- #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_MASK UINT32_C(0x1fc)
- #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_SFT 2
- /*
- * Standard TX Ring mode is used for the allocation of TX ring
- * and underlying scheduling resources that allow bandwidth
- * reservation and limit settings on the queried function. If
- * set to 1, then standard TX ring mode is requested to be
- * enabled on the function being configured.
- */
- #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_ENABLE \
- UINT32_C(0x200)
- /*
- * Standard TX Ring mode is used for the allocation of TX ring
- * and underlying scheduling resources that allow bandwidth
- * reservation and limit settings on the queried function. If
- * set to 1, then the standard TX ring mode is requested to be
- * disabled on the function being configured. In this extended
- * TX ring resource mode, the minimum and maximum bandwidth
- * settings are not supported to allow the allocation of TX
- * rings to span multiple scheduler nodes.
- */
- #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_DISABLE \
- UINT32_C(0x400)
- /*
- * If this bit is set, virtual mac address configured in this
- * command will be persistent over warm boot.
- */
- #define HWRM_FUNC_CFG_INPUT_FLAGS_VIRT_MAC_PERSIST UINT32_C(0x800)
- /*
- * This bit only applies to the VF. If this bit is set, the
- * statistic context counters will not be cleared when the
- * statistic context is freed or a function reset is called on
- * VF. This bit will be cleared when the PF is unloaded or a
- * function reset is called on the PF.
- */
- #define HWRM_FUNC_CFG_INPUT_FLAGS_NO_AUTOCLEAR_STATISTIC \
- UINT32_C(0x1000)
- uint32_t enables;
- /* This bit must be '1' for the mtu field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_MTU UINT32_C(0x1)
- /* This bit must be '1' for the mru field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_MRU UINT32_C(0x2)
- /*
- * This bit must be '1' for the num_rsscos_ctxs field to be
- * configured.
- */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RSSCOS_CTXS UINT32_C(0x4)
- /*
- * This bit must be '1' for the num_cmpl_rings field to be
- * configured.
- */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_CMPL_RINGS UINT32_C(0x8)
- /* This bit must be '1' for the num_tx_rings field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_TX_RINGS UINT32_C(0x10)
- /* This bit must be '1' for the num_rx_rings field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RX_RINGS UINT32_C(0x20)
- /* This bit must be '1' for the num_l2_ctxs field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_L2_CTXS UINT32_C(0x40)
- /* This bit must be '1' for the num_vnics field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_VNICS UINT32_C(0x80)
- /*
- * This bit must be '1' for the num_stat_ctxs field to be
- * configured.
- */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_STAT_CTXS UINT32_C(0x100)
- /*
- * This bit must be '1' for the dflt_mac_addr field to be
- * configured.
- */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_MAC_ADDR UINT32_C(0x200)
- /* This bit must be '1' for the dflt_vlan field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_VLAN UINT32_C(0x400)
- /* This bit must be '1' for the dflt_ip_addr field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_IP_ADDR UINT32_C(0x800)
- /* This bit must be '1' for the min_bw field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_MIN_BW UINT32_C(0x1000)
- /* This bit must be '1' for the max_bw field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_MAX_BW UINT32_C(0x2000)
- /*
- * This bit must be '1' for the async_event_cr field to be
- * configured.
- */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_ASYNC_EVENT_CR UINT32_C(0x4000)
- /*
- * This bit must be '1' for the vlan_antispoof_mode field to be
- * configured.
- */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_VLAN_ANTISPOOF_MODE UINT32_C(0x8000)
- /*
- * This bit must be '1' for the allowed_vlan_pris field to be
- * configured.
- */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_ALLOWED_VLAN_PRIS UINT32_C(0x10000)
- /* This bit must be '1' for the evb_mode field to be configured. */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_EVB_MODE UINT32_C(0x20000)
- /*
- * This bit must be '1' for the num_mcast_filters field to be
- * configured.
- */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_MCAST_FILTERS UINT32_C(0x40000)
- /*
- * This bit must be '1' for the num_hw_ring_grps field to be
- * configured.
- */
- #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_HW_RING_GRPS UINT32_C(0x80000)
- uint16_t mtu;
- /*
- * The maximum transmission unit of the function. The HWRM
- * should make sure that the mtu of the function does not exceed
- * the mtu of the physical port that this function is associated
- * with. In addition to configuring mtu per function, it is
- * possible to configure mtu per transmit ring. By default, the
- * mtu of each transmit ring associated with a function is equal
- * to the mtu of the function. The HWRM should make sure that
- * the mtu of each transmit ring that is assigned to a function
- * has a valid mtu.
- */
- uint16_t mru;
- /*
- * The maximum receive unit of the function. The HWRM should
- * make sure that the mru of the function does not exceed the
- * mru of the physical port that this function is associated
- * with. In addition to configuring mru per function, it is
- * possible to configure mru per vnic. By default, the mru of
- * each vnic associated with a function is equal to the mru of
- * the function. The HWRM should make sure that the mru of each
- * vnic that is assigned to a function has a valid mru.
- */
- uint16_t num_rsscos_ctxs;
- /* The number of RSS/COS contexts requested for the function. */
- uint16_t num_cmpl_rings;
- /*
- * The number of completion rings requested for the function.
- * This does not include the rings allocated to any children
- * functions if any.
- */
- uint16_t num_tx_rings;
- /*
- * The number of transmit rings requested for the function. This
- * does not include the rings allocated to any children
- * functions if any.
- */
- uint16_t num_rx_rings;
- /*
- * The number of receive rings requested for the function. This
- * does not include the rings allocated to any children
- * functions if any.
- */
- uint16_t num_l2_ctxs;
- /* The requested number of L2 contexts for the function. */
- uint16_t num_vnics;
- /* The requested number of vnics for the function. */
- uint16_t num_stat_ctxs;
- /* The requested number of statistic contexts for the function. */
- uint16_t num_hw_ring_grps;
- /*
- * The number of HW ring groups that should be reserved for this
- * function.
- */
- uint8_t dflt_mac_addr[6];
- /* The default MAC address for the function being configured. */
- uint16_t dflt_vlan;
- /*
- * The default VLAN for the function being configured. This
- * field's format is same as 802.1Q Tag's Tag Control
- * Information (TCI) format that includes both Priority Code
- * Point (PCP) and VLAN Identifier (VID).
- */
- uint32_t dflt_ip_addr[4];
- /*
- * The default IP address for the function being configured.
- * This address is only used in enabling source property check.
- */
- uint32_t min_bw;
- /*
- * Minimum BW allocated for this function. The HWRM will
- * translate this value into byte counter and time interval used
- * for the scheduler inside the device.
- */
- /* The bandwidth value. */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_SFT 0
- /* The granularity of the value (bits or bytes). */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE UINT32_C(0x10000000)
- /* Value is in bits. */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BITS (UINT32_C(0x0) << 28)
- /* Value is in bytes. */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES (UINT32_C(0x1) << 28)
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_LAST \
- FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES
- /* bw_value_unit is 3 b */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MASK \
- UINT32_C(0xe0000000)
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_SFT 29
- /* Value is in Mb or MB (base 10). */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MEGA \
- (UINT32_C(0x0) << 29)
- /* Value is in Kb or KB (base 10). */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_KILO \
- (UINT32_C(0x2) << 29)
- /* Value is in bits or bytes. */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_BASE \
- (UINT32_C(0x4) << 29)
- /* Value is in Gb or GB (base 10). */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_GIGA \
- (UINT32_C(0x6) << 29)
- /* Value is in 1/100th of a percentage of total bandwidth. */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
- (UINT32_C(0x1) << 29)
- /* Invalid unit */
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID \
- (UINT32_C(0x7) << 29)
- #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_LAST \
- FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID
- uint32_t max_bw;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * Maximum BW allocated for this function. The HWRM will
- * translate this value into byte counter and time interval used
- * for the scheduler inside the device.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- /* The bandwidth value. */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_MASK \
- UINT32_C(0xfffffff)
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_SFT 0
- /* The granularity of the value (bits or bytes). */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE UINT32_C(0x10000000)
- /* Value is in bits. */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BITS (UINT32_C(0x0) << 28)
- /* Value is in bytes. */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES (UINT32_C(0x1) << 28)
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_LAST \
- FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES
- /* bw_value_unit is 3 b */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MASK \
- UINT32_C(0xe0000000)
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
- /* Value is in Mb or MB (base 10). */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
- (UINT32_C(0x0) << 29)
- /* Value is in Kb or KB (base 10). */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_KILO \
- (UINT32_C(0x2) << 29)
- /* Value is in bits or bytes. */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_BASE \
- (UINT32_C(0x4) << 29)
- /* Value is in Gb or GB (base 10). */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
- (UINT32_C(0x6) << 29)
- /* Value is in 1/100th of a percentage of total bandwidth. */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
- (UINT32_C(0x1) << 29)
- /* Invalid unit */
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
- (UINT32_C(0x7) << 29)
- #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
- FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
- uint16_t async_event_cr;
+ uint64_t resp_addr;
/*
- * ID of the target completion ring for receiving asynchronous
- * event completions. If this field is not valid, then the HWRM
- * shall use the default completion ring of the function that is
- * being configured as the target completion ring for providing
- * any asynchronous event completions for that function. If this
- * field is valid, then the HWRM shall use the completion ring
- * identified by this ID as the target completion ring for
- * providing any asynchronous event completions for the function
- * that is being configured.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint8_t vlan_antispoof_mode;
- /* VLAN Anti-spoofing mode. */
- /* No VLAN anti-spoofing checks are enabled */
- #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_NOCHECK UINT32_C(0x0)
- /* Validate VLAN against the configured VLAN(s) */
- #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_VALIDATE_VLAN \
- UINT32_C(0x1)
- /* Insert VLAN if it does not exist, otherwise discard */
- #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_IF_VLANDNE \
- UINT32_C(0x2)
+ uint32_t enables;
+ /* This bit must be '1' for the new_dst_id field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_DST_ID 0x1UL
/*
- * Insert VLAN if it does not exist, override
- * VLAN if it exists
+ * This bit must be '1' for the new_mirror_vnic_id field to be
+ * configured.
*/
- #define \
- HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_OR_OVERRIDE_VLAN \
- UINT32_C(0x3)
- uint8_t allowed_vlan_pris;
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
+ 0x2UL
/*
- * This bit field defines VLAN PRIs that are allowed on this
- * function. If nth bit is set, then VLAN PRI n is allowed on
- * this function.
+ * This bit must be '1' for the new_meter_instance_id field to
+ * be configured.
*/
- uint8_t evb_mode;
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_METER_INSTANCE_ID \
+ 0x4UL
+ uint32_t unused_0;
+ uint64_t ntuple_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t new_dst_id;
/*
- * The HWRM shall allow a PF driver to change EVB mode for the
- * partition it belongs to. The HWRM shall not allow a VF driver
- * to change the EVB mode. The HWRM shall take into account the
- * switching of EVB mode from one to another and reconfigure
- * hardware resources as appropriately. The switching from VEB
- * to VEPA mode requires the disabling of the loopback traffic.
- * Additionally, source knock outs are handled differently in
- * VEB and VEPA modes.
+ * If set, this value shall represent the new Logical VNIC ID of
+ * the destination VNIC for the RX path and new network port id
+ * of the destination port for the TX path.
*/
- /* No Edge Virtual Bridging (EVB) */
- #define HWRM_FUNC_CFG_INPUT_EVB_MODE_NO_EVB UINT32_C(0x0)
- /* Virtual Ethernet Bridge (VEB) */
- #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEB UINT32_C(0x1)
- /* Virtual Ethernet Port Aggregator (VEPA) */
- #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEPA UINT32_C(0x2)
- uint8_t unused_2;
- uint16_t num_mcast_filters;
+ uint32_t new_mirror_vnic_id;
+ /* New Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint16_t new_meter_instance_id;
/*
- * The number of multicast filters that should be reserved for
- * this function on the RX side.
+ * New meter to attach to the flow. Specifying the invalid
+ * instance ID is used to remove any existing meter from the
+ * flow.
+ */
+ /*
+ * A value of 0xfff is considered invalid and
+ * implies the instance is not configured.
*/
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID \
+ 0xffffUL
+ uint16_t unused_1[3];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_func_cfg_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_ntuple_filter_cfg_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -3513,16 +20816,19 @@ struct hwrm_func_cfg_output {
*/
} __attribute__((packed));
-/* hwrm_func_qstats */
+/* hwrm_cfa_em_flow_alloc */
/*
- * Description: This command returns statistics of a function. The input FID
- * value is used to indicate what function is being queried. This allows a
- * physical function driver to query virtual functions that are children of the
- * physical function. The HWRM shall return any unsupported counter with a value
- * of 0xFFFFFFFF for 32-bit counters and 0xFFFFFFFFFFFFFFFF for 64-bit counters.
+ * Description: This is a generic Exact Match (EM) flow that uses fields from
+ * L4/L3/L2 headers. The EM flows apply to transmit and receive traffic. All
+ * L2/L3/L4 header fields are specified in network byte order. For each EM flow,
+ * there is an associated set of actions specified. For tunneled packets, all
+ * L2/L3/L4 fields specified are fields of inner headers unless otherwise
+ * specified. # If a field specified in this command is not enabled as a valid
+ * field, then that field shall not be used in matching packet header fields
+ * against this EM flow entry.
*/
-/* Input (24 bytes) */
-struct hwrm_func_qstats_input {
+/* Input (112 bytes) */
+struct hwrm_cfa_em_flow_alloc_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -3543,22 +20849,240 @@ struct hwrm_func_qstats_input {
* ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
* - HWRM
*/
- uint64_t resp_addr;
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_TX (0x0UL << 0)
+ /* rx path */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_RX (0x1UL << 0)
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_LAST \
+ CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_RX
+ /*
+ * Setting of this flag indicates enabling of a byte counter for
+ * a given flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_BYTE_CTR 0x2UL
+ /*
+ * Setting of this flag indicates enabling of a packet counter
+ * for a given flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PKT_CTR 0x4UL
+ /*
+ * Setting of this flag indicates de-capsulation action for the
+ * given flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_DECAP 0x8UL
+ /*
+ * Setting of this flag indicates encapsulation action for the
+ * given flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_ENCAP 0x10UL
+ /*
+ * Setting of this flag indicates drop action. If this flag is
+ * not set, then it should be considered accept action.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_DROP 0x20UL
+ /*
+ * Setting of this flag indicates that a meter is expected to be
+ * attached to this flow. This hint can be used when choosing
+ * the action record format required for the flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_METER 0x40UL
+ uint32_t enables;
+ /* This bit must be '1' for the l2_filter_id field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_L2_FILTER_ID 0x1UL
+ /* This bit must be '1' for the tunnel_type field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_TUNNEL_TYPE 0x2UL
+ /* This bit must be '1' for the tunnel_id field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_TUNNEL_ID 0x4UL
+ /* This bit must be '1' for the src_macaddr field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_MACADDR 0x8UL
+ /* This bit must be '1' for the dst_macaddr field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_MACADDR 0x10UL
+ /* This bit must be '1' for the ovlan_vid field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_OVLAN_VID 0x20UL
+ /* This bit must be '1' for the ivlan_vid field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IVLAN_VID 0x40UL
+ /* This bit must be '1' for the ethertype field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_ETHERTYPE 0x80UL
+ /* This bit must be '1' for the src_ipaddr field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_IPADDR 0x100UL
+ /* This bit must be '1' for the dst_ipaddr field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_IPADDR 0x200UL
+ /* This bit must be '1' for the ipaddr_type field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IPADDR_TYPE 0x400UL
+ /* This bit must be '1' for the ip_protocol field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IP_PROTOCOL 0x800UL
+ /* This bit must be '1' for the src_port field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_PORT 0x1000UL
+ /* This bit must be '1' for the dst_port field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_PORT 0x2000UL
+ /* This bit must be '1' for the dst_id field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_ID 0x4000UL
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID 0x8000UL
+ /*
+ * This bit must be '1' for the encap_record_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_ENCAP_RECORD_ID 0x10000UL
+ /*
+ * This bit must be '1' for the meter_instance_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_METER_INSTANCE_ID 0x20000UL
+ uint64_t l2_filter_id;
+ /*
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
+ */
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Non-tunnel */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL 0x0UL
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN 0x1UL
+ /*
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NVGRE 0x2UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside
+ * Ethernet payload
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_L2GRE 0x3UL
+ /* IP in IP */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPIP 0x4UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_GENEVE 0x5UL
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_MPLS 0x6UL
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_STT 0x7UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPGRE 0x8UL
+ /*
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 0x9UL
+ /* Any tunneled traffic */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL 0xffUL
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint32_t tunnel_id;
+ /*
+ * Tunnel identifier. Virtual Network Identifier (VNI). Only
+ * valid with tunnel_types VXLAN, NVGRE, and Geneve. Only lower
+ * 24-bits of VNI field are used in setting up the filter.
+ */
+ uint8_t src_macaddr[6];
+ /*
+ * This value indicates the source MAC address in the Ethernet
+ * header.
+ */
+ uint16_t meter_instance_id;
+ /* The meter instance to attach to the flow. */
+ /*
+ * A value of 0xfff is considered invalid and
+ * implies the instance is not configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_METER_INSTANCE_ID_INVALID 0xffffUL
+ uint8_t dst_macaddr[6];
+ /*
+ * This value indicates the destination MAC address in the
+ * Ethernet header.
+ */
+ uint16_t ovlan_vid;
+ /*
+ * This value indicates the VLAN ID of the outer VLAN tag in the
+ * Ethernet header.
+ */
+ uint16_t ivlan_vid;
+ /*
+ * This value indicates the VLAN ID of the inner VLAN tag in the
+ * Ethernet header.
+ */
+ uint16_t ethertype;
+ /* This value indicates the ethertype in the Ethernet header. */
+ uint8_t ip_addr_type;
+ /*
+ * This value indicates the type of IP address. 4 - IPv4 6 -
+ * IPv6 All others are invalid.
+ */
+ /* invalid */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN 0x0UL
+ /* IPv4 */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 0x4UL
+ /* IPv6 */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 0x6UL
+ uint8_t ip_protocol;
+ /*
+ * The value of protocol filed in IP header. Applies to UDP and
+ * TCP traffic. 6 - TCP 17 - UDP
+ */
+ /* invalid */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN 0x0UL
+ /* TCP */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_TCP 0x6UL
+ /* UDP */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UDP 0x11UL
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint32_t src_ipaddr[4];
+ /*
+ * The value of source IP address to be used in filtering. For
+ * IPv4, first four bytes represent the IP address.
+ */
+ uint32_t dst_ipaddr[4];
+ /*
+ * big_endian = True The value of destination IP address to be
+ * used in filtering. For IPv4, first four bytes represent the
+ * IP address.
+ */
+ uint16_t src_port;
+ /*
+ * The value of source port to be used in filtering. Applies to
+ * UDP and TCP traffic.
+ */
+ uint16_t dst_port;
/*
- * This is the host address where the response will be written
- * when the request is complete. This area must be 16B aligned
- * and must be cleared to zero before the request is made.
+ * The value of destination port to be used in filtering.
+ * Applies to UDP and TCP traffic.
*/
- uint16_t fid;
+ uint16_t dst_id;
/*
- * Function ID of the function that is being queried. 0xFF...
- * (All Fs) if the query is for the requesting function.
+ * If set, this value shall represent the Logical VNIC ID of the
+ * destination VNIC for the RX path and network port id of the
+ * destination port for the TX path.
*/
- uint16_t unused_0[3];
+ uint16_t mirror_vnic_id;
+ /* Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint32_t encap_record_id;
+ /* Logical ID of the encapsulation record. */
+ uint32_t unused_4;
} __attribute__((packed));
-/* Output (176 bytes) */
-struct hwrm_func_qstats_output {
+/* Output (24 bytes) */
+struct hwrm_cfa_em_flow_alloc_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -3574,76 +21098,18 @@ struct hwrm_func_qstats_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint64_t tx_ucast_pkts;
- /* Number of transmitted unicast packets on the function. */
- uint64_t tx_mcast_pkts;
- /* Number of transmitted multicast packets on the function. */
- uint64_t tx_bcast_pkts;
- /* Number of transmitted broadcast packets on the function. */
- uint64_t tx_err_pkts;
- /*
- * Number of transmitted packets that were discarded due to
- * internal NIC resource problems. For transmit, this can only
- * happen if TMP is configured to allow dropping in HOL blocking
- * conditions, which is not a normal configuration.
- */
- uint64_t tx_drop_pkts;
- /*
- * Number of dropped packets on transmit path on the function.
- * These are packets that have been marked for drop by the TE
- * CFA block or are packets that exceeded the transmit MTU limit
- * for the function.
- */
- uint64_t tx_ucast_bytes;
- /* Number of transmitted bytes for unicast traffic on the function. */
- uint64_t tx_mcast_bytes;
- /*
- * Number of transmitted bytes for multicast traffic on the
- * function.
- */
- uint64_t tx_bcast_bytes;
- /*
- * Number of transmitted bytes for broadcast traffic on the
- * function.
- */
- uint64_t rx_ucast_pkts;
- /* Number of received unicast packets on the function. */
- uint64_t rx_mcast_pkts;
- /* Number of received multicast packets on the function. */
- uint64_t rx_bcast_pkts;
- /* Number of received broadcast packets on the function. */
- uint64_t rx_err_pkts;
- /*
- * Number of received packets that were discarded on the
- * function due to resource limitations. This can happen for 3
- * reasons. # The BD used for the packet has a bad format. #
- * There were no BDs available in the ring for the packet. #
- * There were no BDs available on-chip for the packet.
- */
- uint64_t rx_drop_pkts;
+ uint64_t em_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t flow_id;
/*
- * Number of dropped packets on received path on the function.
- * These are packets that have been marked for drop by the RE
- * CFA.
+ * This is the ID of the flow associated with this filter. This
+ * value shall be used to match and associate the flow
+ * identifier returned in completion records. A value of
+ * 0xFFFFFFFF shall indicate no flow id.
*/
- uint64_t rx_ucast_bytes;
- /* Number of received bytes for unicast traffic on the function. */
- uint64_t rx_mcast_bytes;
- /* Number of received bytes for multicast traffic on the function. */
- uint64_t rx_bcast_bytes;
- /* Number of received bytes for broadcast traffic on the function. */
- uint64_t rx_agg_pkts;
- /* Number of aggregated unicast packets on the function. */
- uint64_t rx_agg_bytes;
- /* Number of aggregated unicast bytes on the function. */
- uint64_t rx_agg_events;
- /* Number of aggregation events on the function. */
- uint64_t rx_agg_aborts;
- /* Number of aborted aggregations on the function. */
- uint32_t unused_0;
+ uint8_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
- uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -3655,15 +21121,10 @@ struct hwrm_func_qstats_output {
*/
} __attribute__((packed));
-/* hwrm_func_clr_stats */
-/*
- * Description: This command clears statistics of a function. The input FID
- * value is used to indicate what function's statistics is being cleared. This
- * allows a physical function driver to clear statistics of virtual functions
- * that are children of the physical function.
- */
-/* Input (24 bytes) */
-struct hwrm_func_clr_stats_input {
+/* hwrm_cfa_em_flow_free */
+/* Description: Free an EM flow table entry */
+/* Input (24 bytes) */
+struct hwrm_cfa_em_flow_free_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -3690,16 +21151,12 @@ struct hwrm_func_clr_stats_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t fid;
- /*
- * Function ID of the function. 0xFF... (All Fs) if the query is
- * for the requesting function.
- */
- uint16_t unused_0[3];
+ uint64_t em_filter_id;
+ /* This value is an opaque id into CFA data structures. */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_func_clr_stats_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_em_flow_free_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -3730,10 +21187,12 @@ struct hwrm_func_clr_stats_output {
*/
} __attribute__((packed));
-/* hwrm_func_vf_vnic_ids_query */
-/* Description: This command is used to query vf vnic ids. */
-/* Input (32 bytes) */
-struct hwrm_func_vf_vnic_ids_query_input {
+/* hwrm_cfa_em_flow_cfg */
+/*
+ * Description: Configure an EM flow with a new destination VNIC and/or meter.
+ */
+/* Input (48 bytes) */
+struct hwrm_cfa_em_flow_cfg_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -3760,21 +21219,47 @@ struct hwrm_func_vf_vnic_ids_query_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t vf_id;
+ uint32_t enables;
+ /* This bit must be '1' for the new_dst_id field to be configured. */
+ #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_DST_ID 0x1UL
/*
- * This value is used to identify a Virtual Function (VF). The
- * scope of VF ID is local within a PF.
+ * This bit must be '1' for the new_mirror_vnic_id field to be
+ * configured.
*/
- uint8_t unused_0;
- uint8_t unused_1;
- uint32_t max_vnic_id_cnt;
- /* Max number of vnic ids in vnic id table */
- uint64_t vnic_id_tbl_addr;
- /* This is the address for VF VNIC ID table */
+ #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID 0x2UL
+ /*
+ * This bit must be '1' for the new_meter_instance_id field to
+ * be configured.
+ */
+ #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_METER_INSTANCE_ID 0x4UL
+ uint32_t unused_0;
+ uint64_t em_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t new_dst_id;
+ /*
+ * If set, this value shall represent the new Logical VNIC ID of
+ * the destination VNIC for the RX path and network port id of
+ * the destination port for the TX path.
+ */
+ uint32_t new_mirror_vnic_id;
+ /* New Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint16_t new_meter_instance_id;
+ /*
+ * New meter to attach to the flow. Specifying the invalid
+ * instance ID is used to remove any existing meter from the
+ * flow.
+ */
+ /*
+ * A value of 0xfff is considered invalid and
+ * implies the instance is not configured.
+ */
+ #define HWRM_CFA_EM_FLOW_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID \
+ 0xffffUL
+ uint16_t unused_1[3];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_func_vf_vnic_ids_query_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_em_flow_cfg_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -3790,14 +21275,10 @@ struct hwrm_func_vf_vnic_ids_query_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t vnic_id_cnt;
- /*
- * Actual number of vnic ids Each VNIC ID is written as a 32-bit
- * number.
- */
- uint8_t unused_0;
+ uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -3809,15 +21290,15 @@ struct hwrm_func_vf_vnic_ids_query_output {
*/
} __attribute__((packed));
-/* hwrm_func_drv_rgtr */
+/* hwrm_cfa_meter_profile_alloc */
/*
- * Description: This command is used by the function driver to register its
- * information with the HWRM. A function driver shall implement this command. A
- * function driver shall use this command during the driver initialization right
- * after the HWRM version discovery and default ring resources allocation.
+ * Description: This is a meter profile that defines the characteristics of the
+ * meter. This includes the algorithm, information rates, and burst sizes. No
+ * running state is kept in a profile and instead meter instances are allocated
+ * that reference a profile.
*/
-/* Input (80 bytes) */
-struct hwrm_func_drv_rgtr_input {
+/* Input (40 bytes) */
+struct hwrm_cfa_meter_profile_alloc_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -3844,99 +21325,244 @@ struct hwrm_func_drv_rgtr_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t flags;
- /*
- * When this bit is '1', the function driver is requesting all
- * requests from its children VF drivers to be forwarded to
- * itself. This flag can only be set by the PF driver. If a VF
- * driver sets this flag, it should be ignored by the HWRM.
- */
- #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_ALL_MODE UINT32_C(0x1)
- /*
- * When this bit is '1', the function is requesting none of the
- * requests from its children VF drivers to be forwarded to
- * itself. This flag can only be set by the PF driver. If a VF
- * driver sets this flag, it should be ignored by the HWRM.
- */
- #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_NONE_MODE UINT32_C(0x2)
- uint32_t enables;
- /* This bit must be '1' for the os_type field to be configured. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_OS_TYPE UINT32_C(0x1)
- /* This bit must be '1' for the ver field to be configured. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VER UINT32_C(0x2)
- /* This bit must be '1' for the timestamp field to be configured. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_TIMESTAMP UINT32_C(0x4)
- /* This bit must be '1' for the vf_req_fwd field to be configured. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VF_INPUT_FWD UINT32_C(0x8)
- /*
- * This bit must be '1' for the async_event_fwd field to be
- * configured.
- */
- #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_ASYNC_EVENT_FWD UINT32_C(0x10)
- uint16_t os_type;
- /*
- * This value indicates the type of OS. The values are based on
- * CIM_OperatingSystem.mof file as published by the DMTF.
- */
- /* Unknown */
- #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_UNKNOWN UINT32_C(0x0)
- /* Other OS not listed below. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_OTHER UINT32_C(0x1)
- /* MSDOS OS. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_MSDOS UINT32_C(0xe)
- /* Windows OS. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WINDOWS UINT32_C(0x12)
- /* Solaris OS. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_SOLARIS UINT32_C(0x1d)
- /* Linux OS. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_LINUX UINT32_C(0x24)
- /* FreeBSD OS. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_FREEBSD UINT32_C(0x2a)
- /* VMware ESXi OS. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_ESXI UINT32_C(0x68)
- /* Microsoft Windows 8 64-bit OS. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN864 UINT32_C(0x73)
- /* Microsoft Windows Server 2012 R2 OS. */
- #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN2012R2 UINT32_C(0x74)
- uint8_t ver_maj;
- /* This is the major version of the driver. */
- uint8_t ver_min;
- /* This is the minor version of the driver. */
- uint8_t ver_upd;
- /* This is the update version of the driver. */
- uint8_t unused_0;
- uint16_t unused_1;
- uint32_t timestamp;
- /*
- * This is a 32-bit timestamp provided by the driver for keep
- * alive. The timestamp is in multiples of 1ms.
- */
- uint32_t unused_2;
- uint32_t vf_req_fwd[8];
- /*
- * This is a 256-bit bit mask provided by the PF driver for
- * letting the HWRM know what commands issued by the VF driver
- * to the HWRM should be forwarded to the PF driver. Nth bit
- * refers to the Nth req_type. Setting Nth bit to 1 indicates
- * that requests from the VF driver with req_type equal to N
- * shall be forwarded to the parent PF driver. This field is not
- * valid for the VF driver.
- */
- uint32_t async_event_fwd[8];
- /*
- * This is a 256-bit bit mask provided by the function driver
- * (PF or VF driver) to indicate the list of asynchronous event
- * completions to be forwarded. Nth bit refers to the Nth
- * event_id. Setting Nth bit to 1 by the function driver shall
- * result in the HWRM forwarding asynchronous event completion
- * with event_id equal to N. If all bits are set to 0 (value of
- * 0), then the HWRM shall not forward any asynchronous event
- * completion to this function driver.
+ uint8_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
*/
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_TX 0x0UL
+ /* rx path */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_RX 0x1UL
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_LAST \
+ CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_RX
+ uint8_t meter_type;
+ /* The meter algorithm type. */
+ /* RFC 2697 (srTCM) */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC2697 0x0UL
+ /* RFC 2698 (trTCM) */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC2698 0x1UL
+ /* RFC 4115 (trTCM) */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC4115 0x2UL
+ uint16_t reserved1;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t reserved2;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t commit_rate;
+ /* A meter rate specified in bytes-per-second. */
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_LAST \
+ CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_INVALID
+ uint32_t commit_burst;
+ /* A meter burst size specified in bytes. */
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_LAST \
+ CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID
+ uint32_t excess_peak_rate;
+ /* A meter rate specified in bytes-per-second. */
+ /* The bandwidth value. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_LAST \
+ CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_INVALID
+ uint32_t excess_peak_burst;
+ /* A meter burst size specified in bytes. */
+ /* The bandwidth value. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES \
+ (0x1UL << 28)
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_func_drv_rgtr_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_meter_profile_alloc_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -3952,10 +21578,19 @@ struct hwrm_func_drv_rgtr_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t unused_0;
+ uint16_t meter_profile_id;
+ /* This value identifies a meter profile in CFA. */
+ /*
+ * A value of 0xfff is considered invalid and
+ * implies the profile is not configured.
+ */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_OUTPUT_METER_PROFILE_ID_INVALID \
+ 0xffffUL
+ uint8_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
+ uint8_t unused_4;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -3967,14 +21602,10 @@ struct hwrm_func_drv_rgtr_output {
*/
} __attribute__((packed));
-/* hwrm_func_drv_unrgtr */
-/*
- * Description: This command is used by the function driver to un register with
- * the HWRM. A function driver shall implement this command. A function driver
- * shall use this command during the driver unloading.
- */
-/* Input (24 bytes) */
-struct hwrm_func_drv_unrgtr_input {
+/* hwrm_cfa_meter_profile_free */
+/* Description: Free a meter profile. */
+/* Input (24 bytes) */
+struct hwrm_cfa_meter_profile_free_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -4001,18 +21632,33 @@ struct hwrm_func_drv_unrgtr_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t flags;
+ uint8_t flags;
/*
- * When this bit is '1', the function driver is notifying the
- * HWRM to prepare for the shutdown.
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
*/
- #define HWRM_FUNC_DRV_UNRGTR_INPUT_FLAGS_PREPARE_FOR_SHUTDOWN \
- UINT32_C(0x1)
- uint32_t unused_0;
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_TX 0x0UL
+ /* rx path */
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_RX 0x1UL
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_LAST \
+ CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_RX
+ uint8_t unused_0;
+ uint16_t meter_profile_id;
+ /* This value identifies a meter profile in CFA. */
+ /*
+ * A value of 0xfff is considered invalid and
+ * implies the profile is not configured.
+ */
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_METER_PROFILE_ID_INVALID \
+ 0xffffUL
+ uint32_t unused_1;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_func_drv_unrgtr_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_meter_profile_free_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -4043,16 +21689,10 @@ struct hwrm_func_drv_unrgtr_output {
*/
} __attribute__((packed));
-/* hwrm_func_buf_rgtr */
-/*
- * Description: This command is used by the PF driver to register buffers used
- * in the PF-VF communication with the HWRM. The PF driver uses this command to
- * register buffers for each PF-VF channel. A parent PF may issue this command
- * per child VF. If VF ID is not valid, then this command is used to register
- * buffers for all children VFs of the PF.
- */
-/* Input (128 bytes) */
-struct hwrm_func_buf_rgtr_input {
+/* hwrm_cfa_meter_profile_cfg */
+/* Description: Reconfigure a meter profile. */
+/* Input (40 bytes) */
+struct hwrm_cfa_meter_profile_cfg_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -4079,56 +21719,246 @@ struct hwrm_func_buf_rgtr_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t enables;
- /* This bit must be '1' for the vf_id field to be configured. */
- #define HWRM_FUNC_BUF_RGTR_INPUT_ENABLES_VF_ID UINT32_C(0x1)
- /* This bit must be '1' for the err_buf_addr field to be configured. */
- #define HWRM_FUNC_BUF_RGTR_INPUT_ENABLES_ERR_BUF_ADDR UINT32_C(0x2)
- uint16_t vf_id;
- /*
- * This value is used to identify a Virtual Function (VF). The
- * scope of VF ID is local within a PF.
- */
- uint16_t req_buf_num_pages;
+ uint8_t flags;
/*
- * This field represents the number of pages used for request
- * buffer(s).
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
*/
- uint16_t req_buf_page_size;
- /* This field represents the page size used for request buffer(s). */
- /* 16 bytes */
- #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_16B UINT32_C(0x4)
- /* 4 Kbytes */
- #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_4K UINT32_C(0xc)
- /* 8 Kbytes */
- #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_8K UINT32_C(0xd)
- /* 64 Kbytes */
- #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_64K UINT32_C(0x10)
- /* 2 Mbytes */
- #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_2M UINT32_C(0x15)
- /* 4 Mbytes */
- #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_4M UINT32_C(0x16)
- /* 1 Gbytes */
- #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_1G UINT32_C(0x1e)
- uint16_t req_buf_len;
- /* The length of the request buffer per VF in bytes. */
- uint16_t resp_buf_len;
- /* The length of the response buffer in bytes. */
- uint8_t unused_0;
- uint8_t unused_1;
- uint64_t req_buf_page_addr[10];
- /* This field represents the page address of req buffer. */
- uint64_t error_buf_addr;
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_TX 0x0UL
+ /* rx path */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_RX 0x1UL
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_LAST \
+ CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_RX
+ uint8_t meter_type;
+ /* The meter algorithm type. */
+ /* RFC 2697 (srTCM) */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC2697 0x0UL
+ /* RFC 2698 (trTCM) */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC2698 0x1UL
+ /* RFC 4115 (trTCM) */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC4115 0x2UL
+ uint16_t meter_profile_id;
+ /* This value identifies a meter profile in CFA. */
/*
- * This field is used to receive the error reporting from the
- * chipset. Only applicable for PFs.
+ * A value of 0xfff is considered invalid and
+ * implies the profile is not configured.
*/
- uint64_t resp_buf_addr;
- /* This field is used to receive the response forwarded by the HWRM. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_PROFILE_ID_INVALID \
+ 0xffffUL
+ uint32_t reserved;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t commit_rate;
+ /* A meter rate specified in bytes-per-second. */
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_INVALID
+ uint32_t commit_burst;
+ /* A meter burst size specified in bytes. */
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_BYTES \
+ (0x1UL << 28)
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID
+ uint32_t excess_peak_rate;
+ /* A meter rate specified in bytes-per-second. */
+ /* The bandwidth value. */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES \
+ (0x1UL << 28)
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_INVALID
+ uint32_t excess_peak_burst;
+ /* A meter burst size specified in bytes. */
+ /* The bandwidth value. */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_MASK \
+ 0xfffffffUL
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE \
+ 0x10000000UL
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_BITS \
+ (0x0UL << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES \
+ (0x1UL << 28)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_LAST \
+ CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MASK \
+ 0xe0000000UL
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MEGA \
+ (0x0UL << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_KILO \
+ (0x2UL << 29)
+ /* Value is in bits or bytes. */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_BASE \
+ (0x4UL << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_GIGA \
+ (0x6UL << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_PERCENT1_100 \
+ (0x1UL << 29)
+ /* Invalid unit */
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID \
+ (0x7UL << 29)
+ #define \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_func_buf_rgtr_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_meter_profile_cfg_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -4159,17 +21989,14 @@ struct hwrm_func_buf_rgtr_output {
*/
} __attribute__((packed));
-/* hwrm_func_buf_unrgtr */
+/* hwrm_cfa_meter_instance_alloc */
/*
- * Description: This command is used by the PF driver to unregister buffers used
- * in the PF-VF communication with the HWRM. The PF driver uses this command to
- * unregister buffers for PF-VF communication. A parent PF may issue this
- * command to unregister buffers for communication between the PF and a specific
- * VF. If the VF ID is not valid, then this command is used to unregister
- * buffers used for communications with all children VFs of the PF.
+ * Description: This is a meter instance which is used to track a meter's bucket
+ * fill values for a flow. Each meter instance references a meter profile that
+ * defines the meter algorithm in use.
*/
-/* Input (24 bytes) */
-struct hwrm_func_buf_unrgtr_input {
+/* Input (24 bytes) */
+struct hwrm_cfa_meter_instance_alloc_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -4196,19 +22023,33 @@ struct hwrm_func_buf_unrgtr_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t enables;
- /* This bit must be '1' for the vf_id field to be configured. */
- #define HWRM_FUNC_BUF_UNRGTR_INPUT_ENABLES_VF_ID UINT32_C(0x1)
- uint16_t vf_id;
+ uint8_t flags;
/*
- * This value is used to identify a Virtual Function (VF). The
- * scope of VF ID is local within a PF.
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
*/
- uint16_t unused_0;
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_TX 0x0UL
+ /* rx path */
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_RX 0x1UL
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_LAST \
+ CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_RX
+ uint8_t unused_0;
+ uint16_t meter_profile_id;
+ /* This value identifies a meter profile in CFA. */
+ /*
+ * A value of 0xfff is considered invalid and
+ * implies the profile is not configured.
+ */
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_METER_PROFILE_ID_INVALID \
+ 0xffffUL
+ uint32_t unused_1;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_func_buf_unrgtr_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_meter_instance_alloc_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -4224,10 +22065,19 @@ struct hwrm_func_buf_unrgtr_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t unused_0;
+ uint16_t meter_instance_id;
+ /* This value identifies a meter instance in CFA. */
+ /*
+ * A value of 0xfff is considered invalid and
+ * implies the instance is not configured.
+ */
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_OUTPUT_METER_INSTANCE_ID_INVALID \
+ 0xffffUL
+ uint8_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
+ uint8_t unused_4;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -4239,98 +22089,67 @@ struct hwrm_func_buf_unrgtr_output {
*/
} __attribute__((packed));
-/* hwrm_func_vf_cfg */
-/*
- * Description: This command allows configuration of a VF by its driver. If this
- * function is called by a PF driver, then the HWRM shall fail this command. If
- * guest VLAN and/or MAC address are provided in this command, then the HWRM
- * shall set up appropriate MAC/VLAN filters for the VF that is being
- * configured. A VF driver should set VF MTU/MRU using this command prior to
- * allocating RX VNICs or TX rings for the corresponding VF.
- */
-/* Input (32 bytes) */
-
-struct hwrm_func_vf_cfg_input {
+/* hwrm_cfa_meter_instance_free */
+/* Description: Free a meter instance. */
+/* Input (24 bytes) */
+struct hwrm_cfa_meter_instance_free_input {
uint16_t req_type;
/*
- * This value indicates what type of request this is. The format for the
- * rest of the command is determined by this field.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
uint16_t cmpl_ring;
/*
- * This value indicates the what completion ring the request will be
- * optionally completed on. If the value is -1, then no CR completion
- * will be generated. Any other value must be a valid CR ring_id value
- * for this function.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
uint16_t seq_id;
/* This value indicates the command sequence number. */
uint16_t target_id;
/*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
- * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
uint64_t resp_addr;
/*
- * This is the host address where the response will be written when the
- * request is complete. This area must be 16B aligned and must be
- * cleared to zero before the request is made.
- */
- uint32_t enables;
- /* This bit must be '1' for the mtu field to be configured. */
- #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_MTU UINT32_C(0x1)
- /* This bit must be '1' for the guest_vlan field to be configured. */
- #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_GUEST_VLAN UINT32_C(0x2)
- /*
- * This bit must be '1' for the async_event_cr field to be configured.
- */
- #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_ASYNC_EVENT_CR UINT32_C(0x4)
- /* This bit must be '1' for the dflt_mac_addr field to be configured. */
- #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_DFLT_MAC_ADDR UINT32_C(0x8)
- uint16_t mtu;
- /*
- * The maximum transmission unit requested on the function. The HWRM
- * should make sure that the mtu of the function does not exceed the mtu
- * of the physical port that this function is associated with. In
- * addition to requesting mtu per function, it is possible to configure
- * mtu per transmit ring. By default, the mtu of each transmit ring
- * associated with a function is equal to the mtu of the function. The
- * HWRM should make sure that the mtu of each transmit ring that is
- * assigned to a function has a valid mtu.
- */
- uint16_t guest_vlan;
- /*
- * The guest VLAN for the function being configured. This field's format
- * is same as 802.1Q Tag's Tag Control Information (TCI) format that
- * includes both Priority Code Point (PCP) and VLAN Identifier (VID).
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint16_t async_event_cr;
+ uint8_t flags;
/*
- * ID of the target completion ring for receiving asynchronous event
- * completions. If this field is not valid, then the HWRM shall use the
- * default completion ring of the function that is being configured as
- * the target completion ring for providing any asynchronous event
- * completions for that function. If this field is valid, then the HWRM
- * shall use the completion ring identified by this ID as the target
- * completion ring for providing any asynchronous event completions for
- * the function that is being configured.
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
*/
- uint8_t dflt_mac_addr[6];
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH 0x1UL
+ /* tx path */
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_TX 0x0UL
+ /* rx path */
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_RX 0x1UL
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_LAST \
+ CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_RX
+ uint8_t unused_0;
+ uint16_t meter_instance_id;
+ /* This value identifies a meter instance in CFA. */
/*
- * This value is the current MAC address requested by the VF driver to
- * be configured on this VF. A value of 00-00-00-00-00-00 indicates no
- * MAC address configuration is requested by the VF driver. The parent
- * PF driver may reject or overwrite this MAC address.
+ * A value of 0xfff is considered invalid and
+ * implies the instance is not configured.
*/
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_METER_INSTANCE_ID_INVALID \
+ 0xffffUL
+ uint32_t unused_1;
} __attribute__((packed));
/* Output (16 bytes) */
-
-struct hwrm_func_vf_cfg_output {
+struct hwrm_cfa_meter_instance_free_output {
uint16_t error_code;
/*
- * Pass/Fail or error type Note: receiver to verify the in parameters,
- * and fail the call with an error when appropriate
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
uint16_t req_type;
/* This field returns the type of original request. */
@@ -4348,25 +22167,22 @@ struct hwrm_func_vf_cfg_output {
uint8_t unused_3;
uint8_t valid;
/*
- * This field is used in Output records to indicate that the output is
- * completely written to RAM. This field should be read as '1' to
- * indicate that the output has been completely written. When writing a
- * command completion or response to an internal processor, the order of
- * writes has to be such that this field is written last.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
} __attribute__((packed));
-/* hwrm_port_phy_cfg */
+/* hwrm_cfa_decap_filter_alloc */
/*
- * Description: This command configures the PHY device for the port. It allows
- * setting of the most generic settings for the PHY. The HWRM shall complete
- * this command as soon as PHY settings are configured. They may not be applied
- * when the command response is provided. A VF driver shall not be allowed to
- * configure PHY using this command. In a network partition mode, a PF driver
- * shall not be allowed to configure PHY using this command.
+ * Description: This command uses fields from L4/L3/L2 headers. All L2/L3/L4
+ * header fields are specified in network byte order.
*/
-/* Input (56 bytes) */
-struct hwrm_port_phy_cfg_input {
+/* Input (104 bytes) */
+struct hwrm_cfa_decap_filter_alloc_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -4394,417 +22210,184 @@ struct hwrm_port_phy_cfg_input {
* and must be cleared to zero before the request is made.
*/
uint32_t flags;
- /*
- * When this bit is set to '1', the PHY for the port shall be
- * reset. # If this bit is set to 1, then the HWRM shall reset
- * the PHY after applying PHY configuration changes specified in
- * this command. # In order to guarantee that PHY configuration
- * changes specified in this command take effect, the HWRM
- * client should set this flag to 1. # If this bit is not set to
- * 1, then the HWRM may reset the PHY depending on the current
- * PHY configuration and settings specified in this command.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESET_PHY UINT32_C(0x1)
- /* deprecated bit. Do not use!!! */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_DEPRECATED UINT32_C(0x2)
- /*
- * When this bit is set to '1', the link shall be forced to the
- * force_link_speed value. When this bit is set to '1', the HWRM
- * client should not enable any of the auto negotiation related
- * fields represented by auto_XXX fields in this command. When
- * this bit is set to '1' and the HWRM client has enabled a
- * auto_XXX field in this command, then the HWRM shall ignore
- * the enabled auto_XXX field. When this bit is set to zero, the
- * link shall be allowed to autoneg.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE UINT32_C(0x4)
- /*
- * When this bit is set to '1', the auto-negotiation process
- * shall be restarted on the link.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG UINT32_C(0x8)
- /*
- * When this bit is set to '1', Energy Efficient Ethernet (EEE)
- * is requested to be enabled on this link. If EEE is not
- * supported on this port, then this flag shall be ignored by
- * the HWRM.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_ENABLE UINT32_C(0x10)
- /*
- * When this bit is set to '1', Energy Efficient Ethernet (EEE)
- * is requested to be disabled on this link. If EEE is not
- * supported on this port, then this flag shall be ignored by
- * the HWRM.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_DISABLE UINT32_C(0x20)
- /*
- * When this bit is set to '1' and EEE is enabled on this link,
- * then TX LPI is requested to be enabled on the link. If EEE is
- * not supported on this port, then this flag shall be ignored
- * by the HWRM. If EEE is disabled on this port, then this flag
- * shall be ignored by the HWRM.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI_ENABLE UINT32_C(0x40)
- /*
- * When this bit is set to '1' and EEE is enabled on this link,
- * then TX LPI is requested to be disabled on the link. If EEE
- * is not supported on this port, then this flag shall be
- * ignored by the HWRM. If EEE is disabled on this port, then
- * this flag shall be ignored by the HWRM.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI_DISABLE UINT32_C(0x80)
- /*
- * When set to 1, then the HWRM shall enable FEC
- * autonegotitation on this port if supported. When set to 0,
- * then this flag shall be ignored. If FEC autonegotiation is
- * not supported, then the HWRM shall ignore this flag.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_AUTONEG_ENABLE UINT32_C(0x100)
- /*
- * When set to 1, then the HWRM shall disable FEC
- * autonegotiation on this port if supported. When set to 0,
- * then this flag shall be ignored. If FEC autonegotiation is
- * not supported, then the HWRM shall ignore this flag.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_AUTONEG_DISABLE \
- UINT32_C(0x200)
- /*
- * When set to 1, then the HWRM shall enable FEC CLAUSE 74 (Fire
- * Code) on this port if supported. When set to 0, then this
- * flag shall be ignored. If FEC CLAUSE 74 is not supported,
- * then the HWRM shall ignore this flag.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE74_ENABLE \
- UINT32_C(0x400)
- /*
- * When set to 1, then the HWRM shall disable FEC CLAUSE 74
- * (Fire Code) on this port if supported. When set to 0, then
- * this flag shall be ignored. If FEC CLAUSE 74 is not
- * supported, then the HWRM shall ignore this flag.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE74_DISABLE \
- UINT32_C(0x800)
- /*
- * When set to 1, then the HWRM shall enable FEC CLAUSE 91 (Reed
- * Solomon) on this port if supported. When set to 0, then this
- * flag shall be ignored. If FEC CLAUSE 91 is not supported,
- * then the HWRM shall ignore this flag.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE91_ENABLE \
- UINT32_C(0x1000)
- /*
- * When set to 1, then the HWRM shall disable FEC CLAUSE 91
- * (Reed Solomon) on this port if supported. When set to 0, then
- * this flag shall be ignored. If FEC CLAUSE 91 is not
- * supported, then the HWRM shall ignore this flag.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE91_DISABLE \
- UINT32_C(0x2000)
- /*
- * When this bit is set to '1', the link shall be forced to be
- * taken down. # When this bit is set to '1", all other command
- * input settings related to the link speed shall be ignored.
- * Once the link state is forced down, it can be explicitly
- * cleared from that state by setting this flag to '0'. # If
- * this flag is set to '0', then the link shall be cleared from
- * forced down state if the link is in forced down state. There
- * may be conditions (e.g. out-of-band or sideband configuration
- * changes for the link) outside the scope of the HWRM
- * implementation that may clear forced down link state.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE_LINK_DWN UINT32_C(0x4000)
+ /* ovs_tunnel is 1 b */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_FLAGS_OVS_TUNNEL 0x1UL
uint32_t enables;
- /* This bit must be '1' for the auto_mode field to be configured. */
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_MODE UINT32_C(0x1)
- /* This bit must be '1' for the auto_duplex field to be configured. */
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_DUPLEX UINT32_C(0x2)
- /* This bit must be '1' for the auto_pause field to be configured. */
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_PAUSE UINT32_C(0x4)
- /*
- * This bit must be '1' for the auto_link_speed field to be
- * configured.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED UINT32_C(0x8)
- /*
- * This bit must be '1' for the auto_link_speed_mask field to be
- * configured.
- */
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED_MASK \
- UINT32_C(0x10)
- /* This bit must be '1' for the wirespeed field to be configured. */
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_WIOUTPUTEED UINT32_C(0x20)
- /* This bit must be '1' for the lpbk field to be configured. */
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_LPBK UINT32_C(0x40)
- /* This bit must be '1' for the preemphasis field to be configured. */
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_PREEMPHASIS UINT32_C(0x80)
- /* This bit must be '1' for the force_pause field to be configured. */
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_FORCE_PAUSE UINT32_C(0x100)
+ /* This bit must be '1' for the tunnel_type field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE 0x1UL
+ /* This bit must be '1' for the tunnel_id field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_ID 0x2UL
+ /* This bit must be '1' for the src_macaddr field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_SRC_MACADDR 0x4UL
+ /* This bit must be '1' for the dst_macaddr field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_MACADDR 0x8UL
+ /* This bit must be '1' for the ovlan_vid field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_OVLAN_VID 0x10UL
+ /* This bit must be '1' for the ivlan_vid field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_IVLAN_VID 0x20UL
+ /* This bit must be '1' for the t_ovlan_vid field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_T_OVLAN_VID 0x40UL
+ /* This bit must be '1' for the t_ivlan_vid field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_T_IVLAN_VID 0x80UL
+ /* This bit must be '1' for the ethertype field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_ETHERTYPE 0x100UL
+ /* This bit must be '1' for the src_ipaddr field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR 0x200UL
+ /* This bit must be '1' for the dst_ipaddr field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR 0x400UL
+ /* This bit must be '1' for the ipaddr_type field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_IPADDR_TYPE 0x800UL
+ /* This bit must be '1' for the ip_protocol field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_IP_PROTOCOL 0x1000UL
+ /* This bit must be '1' for the src_port field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT 0x2000UL
+ /* This bit must be '1' for the dst_port field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_PORT 0x4000UL
+ /* This bit must be '1' for the dst_id field to be configured. */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_ID 0x8000UL
/*
- * This bit must be '1' for the eee_link_speed_mask field to be
+ * This bit must be '1' for the mirror_vnic_id field to be
* configured.
*/
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_EEE_LINK_SPEED_MASK \
- UINT32_C(0x200)
- /* This bit must be '1' for the tx_lpi_timer field to be configured. */
- #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_TX_LPI_TIMER UINT32_C(0x400)
- uint16_t port_id;
- /* Port ID of port that is to be configured. */
- uint16_t force_link_speed;
- /*
- * This is the speed that will be used if the force bit is '1'.
- * If unsupported speed is selected, an error will be generated.
- */
- /* 100Mb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100MB UINT32_C(0x1)
- /* 1Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_1GB UINT32_C(0xa)
- /* 2Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2GB UINT32_C(0x14)
- /* 2.5Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2_5GB UINT32_C(0x19)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10GB UINT32_C(0x64)
- /* 20Mb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_20GB UINT32_C(0xc8)
- /* 25Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_25GB UINT32_C(0xfa)
- /* 40Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_40GB UINT32_C(0x190)
- /* 50Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_50GB UINT32_C(0x1f4)
- /* 100Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100GB UINT32_C(0x3e8)
- /* 10Mb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10MB UINT32_C(0xffff)
- uint8_t auto_mode;
- /*
- * This value is used to identify what autoneg mode is used when
- * the link speed is not being forced.
- */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID 0x10000UL
+ uint32_t tunnel_id;
/*
- * Disable autoneg or autoneg disabled. No
- * speeds are selected.
+ * Tunnel identifier. Virtual Network Identifier (VNI). Only
+ * valid with tunnel_types VXLAN, NVGRE, and Geneve. Only lower
+ * 24-bits of VNI field are used in setting up the filter.
*/
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_NONE UINT32_C(0x0)
- /* Select all possible speeds for autoneg mode. */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ALL_SPEEDS UINT32_C(0x1)
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Non-tunnel */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL 0x0UL
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN 0x1UL
/*
- * Select only the auto_link_speed speed for
- * autoneg mode. This mode has been DEPRECATED.
- * An HWRM client should not use this mode.
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
*/
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_SPEED UINT32_C(0x2)
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE 0x2UL
/*
- * Select the auto_link_speed or any speed below
- * that speed for autoneg. This mode has been
- * DEPRECATED. An HWRM client should not use
- * this mode.
+ * Generic Routing Encapsulation (GRE) inside
+ * Ethernet payload
*/
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_OR_BELOW UINT32_C(0x3)
- /*
- * Select the speeds based on the corresponding
- * link speed mask value that is provided.
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE 0x3UL
+ /* IP in IP */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP 0x4UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE 0x5UL
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS 0x6UL
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT 0x7UL
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
*/
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_SPEED_MASK UINT32_C(0x4)
- uint8_t auto_duplex;
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE 0x8UL
/*
- * This is the duplex setting that will be used if the
- * autoneg_mode is "one_speed" or "one_or_below".
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
*/
- /* Half Duplex will be requested. */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_HALF UINT32_C(0x0)
- /* Full duplex will be requested. */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_FULL UINT32_C(0x1)
- /* Both Half and Full dupex will be requested. */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH UINT32_C(0x2)
- uint8_t auto_pause;
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 0x9UL
+ /* Any tunneled traffic */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL 0xffUL
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint8_t src_macaddr[6];
/*
- * This value is used to configure the pause that will be used
- * for autonegotiation. Add text on the usage of auto_pause and
- * force_pause.
+ * This value indicates the source MAC address in the Ethernet
+ * header.
*/
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t dst_macaddr[6];
/*
- * When this bit is '1', Generation of tx pause messages has
- * been requested. Disabled otherwise.
+ * This value indicates the destination MAC address in the
+ * Ethernet header.
*/
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_TX UINT32_C(0x1)
+ uint16_t ovlan_vid;
/*
- * When this bit is '1', Reception of rx pause messages has been
- * requested. Disabled otherwise.
+ * This value indicates the VLAN ID of the outer VLAN tag in the
+ * Ethernet header.
*/
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_RX UINT32_C(0x2)
+ uint16_t ivlan_vid;
/*
- * When set to 1, the advertisement of pause is enabled. # When
- * the auto_mode is not set to none and this flag is set to 1,
- * then the auto_pause bits on this port are being advertised
- * and autoneg pause results are being interpreted. # When the
- * auto_mode is not set to none and this flag is set to 0, the
- * pause is forced as indicated in force_pause, and also
- * advertised as auto_pause bits, but the autoneg results are
- * not interpreted since the pause configuration is being
- * forced. # When the auto_mode is set to none and this flag is
- * set to 1, auto_pause bits should be ignored and should be set
- * to 0.
+ * This value indicates the VLAN ID of the inner VLAN tag in the
+ * Ethernet header.
*/
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_AUTONEG_PAUSE UINT32_C(0x4)
- uint8_t unused_0;
- uint16_t auto_link_speed;
+ uint16_t t_ovlan_vid;
/*
- * This is the speed that will be used if the autoneg_mode is
- * "one_speed" or "one_or_below". If an unsupported speed is
- * selected, an error will be generated.
+ * This value indicates the VLAN ID of the outer VLAN tag in the
+ * tunnel Ethernet header.
*/
- /* 100Mb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100MB UINT32_C(0x1)
- /* 1Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_1GB UINT32_C(0xa)
- /* 2Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2GB UINT32_C(0x14)
- /* 2.5Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2_5GB UINT32_C(0x19)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10GB UINT32_C(0x64)
- /* 20Mb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_20GB UINT32_C(0xc8)
- /* 25Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_25GB UINT32_C(0xfa)
- /* 40Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_40GB UINT32_C(0x190)
- /* 50Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_50GB UINT32_C(0x1f4)
- /* 100Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100GB UINT32_C(0x3e8)
- /* 10Mb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10MB UINT32_C(0xffff)
- uint16_t auto_link_speed_mask;
+ uint16_t t_ivlan_vid;
/*
- * This is a mask of link speeds that will be used if
- * autoneg_mode is "mask". If unsupported speed is enabled an
- * error will be generated.
+ * This value indicates the VLAN ID of the inner VLAN tag in the
+ * tunnel Ethernet header.
*/
- /* 100Mb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MBHD \
- UINT32_C(0x1)
- /* 100Mb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MB \
- UINT32_C(0x2)
- /* 1Gb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GBHD \
- UINT32_C(0x4)
- /* 1Gb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GB \
- UINT32_C(0x8)
- /* 2Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2GB \
- UINT32_C(0x10)
- /* 2.5Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2_5GB \
- UINT32_C(0x20)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10GB UINT32_C(0x40)
- /* 20Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_20GB UINT32_C(0x80)
- /* 25Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_25GB \
- UINT32_C(0x100)
- /* 40Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_40GB \
- UINT32_C(0x200)
- /* 50Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_50GB \
- UINT32_C(0x400)
- /* 100Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100GB \
- UINT32_C(0x800)
- /* 10Mb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MBHD \
- UINT32_C(0x1000)
- /* 10Mb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MB \
- UINT32_C(0x2000)
- uint8_t wirespeed;
- /* This value controls the wirespeed feature. */
- /* Wirespeed feature is disabled. */
- #define HWRM_PORT_PHY_CFG_INPUT_WIOUTPUTEED_OFF UINT32_C(0x0)
- /* Wirespeed feature is enabled. */
- #define HWRM_PORT_PHY_CFG_INPUT_WIOUTPUTEED_ON UINT32_C(0x1)
- uint8_t lpbk;
- /* This value controls the loopback setting for the PHY. */
- /* No loopback is selected. Normal operation. */
- #define HWRM_PORT_PHY_CFG_INPUT_LPBK_NONE UINT32_C(0x0)
+ uint16_t ethertype;
+ /* This value indicates the ethertype in the Ethernet header. */
+ uint8_t ip_addr_type;
/*
- * The HW will be configured with local loopback
- * such that host data is sent back to the host
- * without modification.
+ * This value indicates the type of IP address. 4 - IPv4 6 -
+ * IPv6 All others are invalid.
*/
- #define HWRM_PORT_PHY_CFG_INPUT_LPBK_LOCAL UINT32_C(0x1)
+ /* invalid */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN 0x0UL
+ /* IPv4 */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 0x4UL
+ /* IPv6 */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 0x6UL
+ uint8_t ip_protocol;
/*
- * The HW will be configured with remote
- * loopback such that port logic will send
- * packets back out the transmitter that are
- * received.
+ * The value of protocol filed in IP header. Applies to UDP and
+ * TCP traffic. 6 - TCP 17 - UDP
*/
- #define HWRM_PORT_PHY_CFG_INPUT_LPBK_REMOTE UINT32_C(0x2)
- uint8_t force_pause;
+ /* invalid */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN 0x0UL
+ /* TCP */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_TCP 0x6UL
+ /* UDP */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP 0x11UL
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t unused_6[3];
+ uint8_t unused_7;
+ uint32_t src_ipaddr[4];
/*
- * This value is used to configure the pause that will be used
- * for force mode.
+ * The value of source IP address to be used in filtering. For
+ * IPv4, first four bytes represent the IP address.
*/
+ uint32_t dst_ipaddr[4];
/*
- * When this bit is '1', Generation of tx pause messages is
- * supported. Disabled otherwise.
+ * The value of destination IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
*/
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_TX UINT32_C(0x1)
+ uint16_t src_port;
/*
- * When this bit is '1', Reception of rx pause messages is
- * supported. Disabled otherwise.
+ * The value of source port to be used in filtering. Applies to
+ * UDP and TCP traffic.
*/
- #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_RX UINT32_C(0x2)
- uint8_t unused_1;
- uint32_t preemphasis;
+ uint16_t dst_port;
/*
- * This value controls the pre-emphasis to be used for the link.
- * Driver should not set this value (use enable.preemphasis = 0)
- * unless driver is sure of setting. Normally HWRM FW will
- * determine proper pre-emphasis.
+ * The value of destination port to be used in filtering.
+ * Applies to UDP and TCP traffic.
*/
- uint16_t eee_link_speed_mask;
+ uint16_t dst_id;
/*
- * Setting for link speed mask that is used to advertise speeds
- * during autonegotiation when EEE is enabled. This field is
- * valid only when EEE is enabled. The speeds specified in this
- * field shall be a subset of speeds specified in
- * auto_link_speed_mask. If EEE is enabled,then at least one
- * speed shall be provided in this mask.
+ * If set, this value shall represent the Logical VNIC ID of the
+ * destination VNIC for the RX path.
*/
- /* Reserved */
- #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD1 UINT32_C(0x1)
- /* 100Mb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_100MB UINT32_C(0x2)
- /* Reserved */
- #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD2 UINT32_C(0x4)
- /* 1Gb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_1GB UINT32_C(0x8)
- /* Reserved */
- #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD3 UINT32_C(0x10)
- /* Reserved */
- #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD4 UINT32_C(0x20)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_10GB UINT32_C(0x40)
- uint8_t unused_2;
- uint8_t unused_3;
- uint32_t tx_lpi_timer;
- uint32_t unused_4;
+ uint16_t l2_ctxt_ref_id;
/*
- * Reuested setting of TX LPI timer in microseconds. This field
- * is valid only when EEE is enabled and TX LPI is enabled.
+ * If set, this value shall represent the L2 context that
+ * matches the L2 information of the decap filter.
*/
- #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_MASK UINT32_C(0xffffff)
- #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_SFT 0
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_port_phy_cfg_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_decap_filter_alloc_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -4820,10 +22403,11 @@ struct hwrm_port_phy_cfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t unused_0;
+ uint32_t decap_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint8_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
- uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -4835,10 +22419,10 @@ struct hwrm_port_phy_cfg_output {
*/
} __attribute__((packed));
-/* hwrm_port_phy_qcfg */
-/* Description: This command queries the PHY configuration for the port. */
-/* Input (24 bytes) */
-struct hwrm_port_phy_qcfg_input {
+/* hwrm_cfa_decap_filter_free */
+/* Description: Free an decap filter table entry */
+/* Input (24 bytes) */
+struct hwrm_cfa_decap_filter_free_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -4865,13 +22449,13 @@ struct hwrm_port_phy_qcfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t port_id;
- /* Port ID of port that is to be queried. */
- uint16_t unused_0[3];
+ uint32_t decap_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t unused_0;
} __attribute__((packed));
-/* Output (96 bytes) */
-struct hwrm_port_phy_qcfg_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_decap_filter_free_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -4887,717 +22471,552 @@ struct hwrm_port_phy_qcfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint8_t link;
- /* This value indicates the current link status. */
- /* There is no link or cable detected. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_NO_LINK UINT32_C(0x0)
- /* There is no link, but a cable has been detected. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SIGNAL UINT32_C(0x1)
- /* There is a link. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_LINK UINT32_C(0x2)
- uint8_t unused_0;
- uint16_t link_speed;
- /* This value indicates the current link speed of the connection. */
- /* 100Mb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100MB UINT32_C(0x1)
- /* 1Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_1GB UINT32_C(0xa)
- /* 2Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2GB UINT32_C(0x14)
- /* 2.5Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2_5GB UINT32_C(0x19)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10GB UINT32_C(0x64)
- /* 20Mb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_20GB UINT32_C(0xc8)
- /* 25Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_25GB UINT32_C(0xfa)
- /* 40Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_40GB UINT32_C(0x190)
- /* 50Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_50GB UINT32_C(0x1f4)
- /* 100Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100GB UINT32_C(0x3e8)
- /* 10Mb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10MB UINT32_C(0xffff)
- uint8_t duplex;
- /* This value is indicates the duplex of the current connection. */
- /* Half Duplex connection. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_HALF UINT32_C(0x0)
- /* Full duplex connection. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_FULL UINT32_C(0x1)
- uint8_t pause;
- /*
- * This value is used to indicate the current pause
- * configuration. When autoneg is enabled, this value represents
- * the autoneg results of pause configuration.
- */
- /*
- * When this bit is '1', Generation of tx pause messages is
- * supported. Disabled otherwise.
- */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_TX UINT32_C(0x1)
- /*
- * When this bit is '1', Reception of rx pause messages is
- * supported. Disabled otherwise.
- */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_RX UINT32_C(0x2)
- uint16_t support_speeds;
- /*
- * The supported speeds for the port. This is a bit mask. For
- * each speed that is supported, the corrresponding bit will be
- * set to '1'.
- */
- /* 100Mb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MBHD UINT32_C(0x1)
- /* 100Mb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MB UINT32_C(0x2)
- /* 1Gb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GBHD UINT32_C(0x4)
- /* 1Gb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GB UINT32_C(0x8)
- /* 2Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2GB UINT32_C(0x10)
- /* 2.5Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2_5GB UINT32_C(0x20)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10GB UINT32_C(0x40)
- /* 20Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_20GB UINT32_C(0x80)
- /* 25Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_25GB UINT32_C(0x100)
- /* 40Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_40GB UINT32_C(0x200)
- /* 50Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_50GB UINT32_C(0x400)
- /* 100Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100GB UINT32_C(0x800)
- /* 10Mb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MBHD UINT32_C(0x1000)
- /* 10Mb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MB UINT32_C(0x2000)
- uint16_t force_link_speed;
- /*
- * Current setting of forced link speed. When the link speed is
- * not being forced, this value shall be set to 0.
- */
- /* 100Mb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100MB UINT32_C(0x1)
- /* 1Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_1GB UINT32_C(0xa)
- /* 2Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2GB UINT32_C(0x14)
- /* 2.5Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2_5GB UINT32_C(0x19)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10GB UINT32_C(0x64)
- /* 20Mb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_20GB UINT32_C(0xc8)
- /* 25Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_25GB UINT32_C(0xfa)
- /* 40Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_40GB UINT32_C(0x190)
- /* 50Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_50GB UINT32_C(0x1f4)
- /* 100Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100GB UINT32_C(0x3e8)
- /* 10Mb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10MB UINT32_C(0xffff)
- uint8_t auto_mode;
- /* Current setting of auto negotiation mode. */
- /*
- * Disable autoneg or autoneg disabled. No
- * speeds are selected.
- */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_NONE UINT32_C(0x0)
- /* Select all possible speeds for autoneg mode. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ALL_SPEEDS UINT32_C(0x1)
- /*
- * Select only the auto_link_speed speed for
- * autoneg mode. This mode has been DEPRECATED.
- * An HWRM client should not use this mode.
- */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_SPEED UINT32_C(0x2)
- /*
- * Select the auto_link_speed or any speed below
- * that speed for autoneg. This mode has been
- * DEPRECATED. An HWRM client should not use
- * this mode.
- */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_OR_BELOW UINT32_C(0x3)
- /*
- * Select the speeds based on the corresponding
- * link speed mask value that is provided.
- */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_SPEED_MASK UINT32_C(0x4)
- uint8_t auto_pause;
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
/*
- * Current setting of pause autonegotiation. Move autoneg_pause
- * flag here.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
+} __attribute__((packed));
+
+/* hwrm_cfa_flow_alloc */
+/* Description: Flow is added to table and resources are allocated. */
+/* Input (128 bytes) */
+struct hwrm_cfa_flow_alloc_input {
+ uint16_t req_type;
/*
- * When this bit is '1', Generation of tx pause messages has
- * been requested. Disabled otherwise.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_TX UINT32_C(0x1)
+ uint16_t cmpl_ring;
/*
- * When this bit is '1', Reception of rx pause messages has been
- * requested. Disabled otherwise.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_RX UINT32_C(0x2)
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * When set to 1, the advertisement of pause is enabled. # When
- * the auto_mode is not set to none and this flag is set to 1,
- * then the auto_pause bits on this port are being advertised
- * and autoneg pause results are being interpreted. # When the
- * auto_mode is not set to none and this flag is set to 0, the
- * pause is forced as indicated in force_pause, and also
- * advertised as auto_pause bits, but the autoneg results are
- * not interpreted since the pause configuration is being
- * forced. # When the auto_mode is set to none and this flag is
- * set to 1, auto_pause bits should be ignored and should be set
- * to 0.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_AUTONEG_PAUSE UINT32_C(0x4)
- uint16_t auto_link_speed;
+ uint64_t resp_addr;
/*
- * Current setting for auto_link_speed. This field is only valid
- * when auto_mode is set to "one_speed" or "one_or_below".
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- /* 100Mb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100MB UINT32_C(0x1)
- /* 1Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_1GB UINT32_C(0xa)
- /* 2Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2GB UINT32_C(0x14)
- /* 2.5Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2_5GB UINT32_C(0x19)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10GB UINT32_C(0x64)
- /* 20Mb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_20GB UINT32_C(0xc8)
- /* 25Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_25GB UINT32_C(0xfa)
- /* 40Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_40GB UINT32_C(0x190)
- /* 50Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_50GB UINT32_C(0x1f4)
- /* 100Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100GB UINT32_C(0x3e8)
- /* 10Mb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10MB UINT32_C(0xffff)
- uint16_t auto_link_speed_mask;
+ uint16_t flags;
+ /* tunnel is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_TUNNEL 0x1UL
+ /* num_vlan is 2 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_MASK 0x6UL
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_SFT 1
+ /* no tags */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_NONE (0x0UL << 1)
+ /* 1 tag */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_ONE (0x1UL << 1)
+ /* 2 tags */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_TWO (0x2UL << 1)
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_LAST \
+ CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_TWO
+ /* Enumeration denoting the Flow Type. */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_MASK 0x38UL
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_SFT 3
+ /* L2 flow */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_L2 (0x0UL << 3)
+ /* IPV4 flow */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_IPV4 (0x1UL << 3)
+ /* IPV6 flow */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_IPV6 (0x2UL << 3)
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_LAST \
+ CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_IPV6
+ uint16_t src_fid;
+ /* Tx Flow: vf fid. Rx Flow: pf fid. */
+ uint32_t tunnel_handle;
+ /* Tunnel handle valid when tunnel flag is set. */
+ uint16_t action_flags;
/*
- * Current setting for auto_link_speed_mask that is used to
- * advertise speeds during autonegotiation. This field is only
- * valid when auto_mode is set to "mask". The speeds specified
- * in this field shall be a subset of supported speeds on this
- * port.
+ * Setting of this flag indicates drop action. If this flag is
+ * not set, then it should be considered accept action.
*/
- /* 100Mb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MBHD \
- UINT32_C(0x1)
- /* 100Mb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MB \
- UINT32_C(0x2)
- /* 1Gb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GBHD \
- UINT32_C(0x4)
- /* 1Gb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GB UINT32_C(0x8)
- /* 2Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2GB \
- UINT32_C(0x10)
- /* 2.5Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2_5GB \
- UINT32_C(0x20)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10GB \
- UINT32_C(0x40)
- /* 20Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_20GB \
- UINT32_C(0x80)
- /* 25Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_25GB \
- UINT32_C(0x100)
- /* 40Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_40GB \
- UINT32_C(0x200)
- /* 50Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_50GB \
- UINT32_C(0x400)
- /* 100Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100GB \
- UINT32_C(0x800)
- /* 10Mb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MBHD \
- UINT32_C(0x1000)
- /* 10Mb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MB \
- UINT32_C(0x2000)
- uint8_t wirespeed;
- /* Current setting for wirespeed. */
- /* Wirespeed feature is disabled. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_WIOUTPUTEED_OFF UINT32_C(0x0)
- /* Wirespeed feature is enabled. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_WIOUTPUTEED_ON UINT32_C(0x1)
- uint8_t lpbk;
- /* Current setting for loopback. */
- /* No loopback is selected. Normal operation. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_NONE UINT32_C(0x0)
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_FWD 0x1UL
+ /* recycle is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_RECYCLE 0x2UL
/*
- * The HW will be configured with local loopback
- * such that host data is sent back to the host
- * without modification.
+ * Setting of this flag indicates drop action. If this flag is
+ * not set, then it should be considered accept action.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_LOCAL UINT32_C(0x1)
- /*
- * The HW will be configured with remote
- * loopback such that port logic will send
- * packets back out the transmitter that are
- * received.
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_DROP 0x4UL
+ /* meter is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_METER 0x8UL
+ /* tunnel is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_TUNNEL 0x10UL
+ /* nat_src is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_NAT_SRC 0x20UL
+ /* nat_dest is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_NAT_DEST 0x40UL
+ /* nat_ipv4_address is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_NAT_IPV4_ADDRESS 0x80UL
+ /* l2_header_rewrite is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_L2_HEADER_REWRITE 0x100UL
+ /* ttl_decrement is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_TTL_DECREMENT 0x200UL
+ uint16_t dst_fid;
+ /* Tx Flow: pf or vf fid. Rx Flow: vf fid. */
+ uint16_t l2_rewrite_vlan_tpid;
+ /* VLAN tpid, valid when push_vlan flag is set. */
+ uint16_t l2_rewrite_vlan_tci;
+ /* VLAN tci, valid when push_vlan flag is set. */
+ uint16_t act_meter_id;
+ /* Meter id, valid when meter flag is set. */
+ uint16_t ref_flow_handle;
+ /* Flow with the same l2 context tcam key. */
+ uint16_t ethertype;
+ /* This value sets the match value for the ethertype. */
+ uint16_t outer_vlan_tci;
+ /* valid when num tags is 1 or 2. */
+ uint16_t dmac[3];
+ /* This value sets the match value for the Destination MAC address. */
+ uint16_t inner_vlan_tci;
+ /* valid when num tags is 2. */
+ uint16_t smac[3];
+ /* This value sets the match value for the Source MAC address. */
+ uint8_t ip_dst_mask_len;
+ /* The bit length of destination IP address mask. */
+ uint8_t ip_src_mask_len;
+ /* The bit length of source IP address mask. */
+ uint32_t ip_dst[4];
+ /* The value of destination IPv4/IPv6 address. */
+ uint32_t ip_src[4];
+ /* The source IPv4/IPv6 address. */
+ uint16_t l4_src_port;
+ /* The value of source port. Applies to UDP and TCP traffic. */
+ uint16_t l4_src_port_mask;
+ /* The value of source port mask. Applies to UDP and TCP traffic. */
+ uint16_t l4_dst_port;
+ /* The value of destination port. Applies to UDP and TCP traffic. */
+ uint16_t l4_dst_port_mask;
+ /*
+ * The value of destination port mask. Applies to UDP and TCP
+ * traffic.
+ */
+ uint32_t nat_ip_address[4];
+ /*
+ * NAT IPv4/6 address based on address type flag. 0 values are
+ * ignored.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_REMOTE UINT32_C(0x2)
- uint8_t force_pause;
+ uint16_t l2_rewrite_dmac[3];
+ /* L2 header re-write Destination MAC address. */
+ uint16_t nat_port;
/*
- * Current setting of forced pause. When the pause configuration
- * is not being forced, then this value shall be set to 0.
+ * The NAT source/destination port based on direction flag.
+ * Applies to UDP and TCP traffic. 0 values are ignored.
*/
+ uint16_t l2_rewrite_smac[3];
+ /* L2 header re-write Source MAC address. */
+ uint8_t ip_proto;
+ /* The value of ip protocol. */
+ uint8_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_flow_alloc_output {
+ uint16_t error_code;
/*
- * When this bit is '1', Generation of tx pause messages is
- * supported. Disabled otherwise.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_TX UINT32_C(0x1)
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * When this bit is '1', Reception of rx pause messages is
- * supported. Disabled otherwise.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_RX UINT32_C(0x2)
- uint8_t module_status;
+ uint16_t flow_handle;
+ /* Flow record index. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
/*
- * This value indicates the current status of the optics module
- * on this port.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- /* Module is inserted and accepted */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NONE UINT32_C(0x0)
- /* Module is rejected and transmit side Laser is disabled. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_DISABLETX UINT32_C(0x1)
- /* Module mismatch warning. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_WARNINGMSG UINT32_C(0x2)
- /* Module is rejected and powered down. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_PWRDOWN UINT32_C(0x3)
- /* Module is not inserted. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTINSERTED \
- UINT32_C(0x4)
- /* Module status is not applicable. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTAPPLICABLE \
- UINT32_C(0xff)
- uint32_t preemphasis;
- /* Current setting for preemphasis. */
- uint8_t phy_maj;
- /* This field represents the major version of the PHY. */
- uint8_t phy_min;
- /* This field represents the minor version of the PHY. */
- uint8_t phy_bld;
- /* This field represents the build version of the PHY. */
- uint8_t phy_type;
- /* This value represents a PHY type. */
- /* Unknown */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_UNKNOWN UINT32_C(0x0)
- /* BASE-CR */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASECR UINT32_C(0x1)
- /* BASE-KR4 (Deprecated) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR4 UINT32_C(0x2)
- /* BASE-LR */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASELR UINT32_C(0x3)
- /* BASE-SR */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASESR UINT32_C(0x4)
- /* BASE-KR2 (Deprecated) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR2 UINT32_C(0x5)
- /* BASE-KX */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKX UINT32_C(0x6)
- /* BASE-KR */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR UINT32_C(0x7)
- /* BASE-T */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASET UINT32_C(0x8)
- /* EEE capable BASE-T */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASETE UINT32_C(0x9)
- /* SGMII connected external PHY */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_SGMIIEXTPHY UINT32_C(0xa)
- /* 25G_BASECR_CA_L */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_L UINT32_C(0xb)
- /* 25G_BASECR_CA_S */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_S UINT32_C(0xc)
- /* 25G_BASECR_CA_N */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_N UINT32_C(0xd)
- /* 25G_BASESR */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASESR UINT32_C(0xe)
- /* 100G_BASECR4 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASECR4 UINT32_C(0xf)
- /* 100G_BASESR4 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASESR4 UINT32_C(0x10)
- /* 100G_BASELR4 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASELR4 UINT32_C(0x11)
- /* 100G_BASEER4 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASEER4 UINT32_C(0x12)
- /* 100G_BASESR10 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASESR10 UINT32_C(0x13)
- /* 40G_BASECR4 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASECR4 UINT32_C(0x14)
- /* 40G_BASESR4 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASESR4 UINT32_C(0x15)
- /* 40G_BASELR4 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASELR4 UINT32_C(0x16)
- /* 40G_BASEER4 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASEER4 UINT32_C(0x17)
- /* 40G_ACTIVE_CABLE */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_ACTIVE_CABLE \
- UINT32_C(0x18)
- uint8_t media_type;
- /* This value represents a media type. */
- /* Unknown */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_UNKNOWN UINT32_C(0x0)
- /* Twisted Pair */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_TP UINT32_C(0x1)
- /* Direct Attached Copper */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_DAC UINT32_C(0x2)
- /* Fiber */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_FIBRE UINT32_C(0x3)
- uint8_t xcvr_pkg_type;
- /* This value represents a transceiver type. */
- /* PHY and MAC are in the same package */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_INTERNAL \
- UINT32_C(0x1)
- /* PHY and MAC are in different packages */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_EXTERNAL \
- UINT32_C(0x2)
- uint8_t eee_config_phy_addr;
+} __attribute__((packed));
+
+/* hwrm_cfa_flow_free */
+/* Description: Flow is removed from table and resources are released. */
+/* Input (24 bytes) */
+struct hwrm_cfa_flow_free_input {
+ uint16_t req_type;
/*
- * This field represents flags related to EEE configuration.
- * These EEE configuration flags are valid only when the
- * auto_mode is not set to none (in other words autonegotiation
- * is enabled).
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- /* This field represents PHY address. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_MASK UINT32_C(0x1f)
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_SFT 0
+ uint16_t cmpl_ring;
/*
- * When set to 1, Energy Efficient Ethernet (EEE) mode is
- * enabled. Speeds for autoneg with EEE mode enabled are based
- * on eee_link_speed_mask.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ENABLED UINT32_C(0x20)
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * This flag is valid only when eee_enabled is set to 1. # If
- * eee_enabled is set to 0, then EEE mode is disabled and this
- * flag shall be ignored. # If eee_enabled is set to 1 and this
- * flag is set to 1, then Energy Efficient Ethernet (EEE) mode
- * is enabled and in use. # If eee_enabled is set to 1 and this
- * flag is set to 0, then Energy Efficient Ethernet (EEE) mode
- * is enabled but is currently not in use.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ACTIVE UINT32_C(0x40)
+ uint64_t resp_addr;
/*
- * This flag is valid only when eee_enabled is set to 1. # If
- * eee_enabled is set to 0, then EEE mode is disabled and this
- * flag shall be ignored. # If eee_enabled is set to 1 and this
- * flag is set to 1, then Energy Efficient Ethernet (EEE) mode
- * is enabled and TX LPI is enabled. # If eee_enabled is set to
- * 1 and this flag is set to 0, then Energy Efficient Ethernet
- * (EEE) mode is enabled but TX LPI is disabled.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_TX_LPI UINT32_C(0x80)
+ uint16_t flow_handle;
+ /* Flow record index. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (32 bytes) */
+struct hwrm_cfa_flow_free_output {
+ uint16_t error_code;
/*
- * This field represents flags related to EEE configuration.
- * These EEE configuration flags are valid only when the
- * auto_mode is not set to none (in other words autonegotiation
- * is enabled).
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_MASK UINT32_C(0xe0)
- #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_SFT 5
- uint8_t parallel_detect;
- /* Reserved field, set to 0 */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * When set to 1, the parallel detection is used to determine
- * the speed of the link partner. Parallel detection is used
- * when a autonegotiation capable device is connected to a link
- * parter that is not capable of autonegotiation.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_PARALLEL_DETECT UINT32_C(0x1)
- /* Reserved field, set to 0 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_MASK UINT32_C(0xfe)
- #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_SFT 1
- uint16_t link_partner_adv_speeds;
+ uint64_t packet;
+ /* packet is 64 b */
+ uint64_t byte;
+ /* byte is 64 b */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
/*
- * The advertised speeds for the port by the link partner. Each
- * advertised speed will be set to '1'.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- /* 100Mb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MBHD \
- UINT32_C(0x1)
- /* 100Mb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MB \
- UINT32_C(0x2)
- /* 1Gb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GBHD \
- UINT32_C(0x4)
- /* 1Gb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GB \
- UINT32_C(0x8)
- /* 2Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2GB \
- UINT32_C(0x10)
- /* 2.5Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2_5GB \
- UINT32_C(0x20)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10GB \
- UINT32_C(0x40)
- /* 20Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_20GB \
- UINT32_C(0x80)
- /* 25Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_25GB \
- UINT32_C(0x100)
- /* 40Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_40GB \
- UINT32_C(0x200)
- /* 50Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_50GB \
- UINT32_C(0x400)
- /* 100Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100GB \
- UINT32_C(0x800)
- /* 10Mb link speed (Half-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MBHD \
- UINT32_C(0x1000)
- /* 10Mb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MB \
- UINT32_C(0x2000)
- uint8_t link_partner_adv_auto_mode;
+} __attribute__((packed));
+
+/* hwrm_cfa_flow_info */
+/* Description: Flow record content for specified flow is returned. */
+/* Input (24 bytes) */
+struct hwrm_cfa_flow_info_input {
+ uint16_t req_type;
/*
- * The advertised autoneg for the port by the link partner. This
- * field is deprecated and should be set to 0.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
+ uint16_t cmpl_ring;
/*
- * Disable autoneg or autoneg disabled. No
- * speeds are selected.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_NONE \
- UINT32_C(0x0)
- /* Select all possible speeds for autoneg mode. */
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ALL_SPEEDS \
- UINT32_C(0x1)
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * Select only the auto_link_speed speed for
- * autoneg mode. This mode has been DEPRECATED.
- * An HWRM client should not use this mode.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_SPEED \
- UINT32_C(0x2)
+ uint64_t resp_addr;
/*
- * Select the auto_link_speed or any speed below
- * that speed for autoneg. This mode has been
- * DEPRECATED. An HWRM client should not use
- * this mode.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_OR_BELOW \
- UINT32_C(0x3)
+ uint16_t flow_handle;
+ /* Flow record index. */
+ /* Max flow handle */
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_MAX_MASK 0xfffUL
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_MAX_SFT 0
+ /* CNP flow handle */
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_CNP_CNT 0x1000UL
+ /* Reserved */
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_RESERVED_MASK 0x6000UL
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_RESERVED_SFT 13
+ /* Direction rx = 1 */
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_DIR_RX 0x8000UL
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (56 bytes) */
+struct hwrm_cfa_flow_info_output {
+ uint16_t error_code;
/*
- * Select the speeds based on the corresponding
- * link speed mask value that is provided.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK \
- UINT32_C(0x4)
- uint8_t link_partner_adv_pause;
- /* The advertised pause settings on the port by the link partner. */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * When this bit is '1', Generation of tx pause messages is
- * supported. Disabled otherwise.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_TX \
- UINT32_C(0x1)
+ uint8_t flags;
+ /* flags is 8 b */
+ uint8_t profile;
+ /* profile is 8 b */
+ uint16_t src_fid;
+ /* src_fid is 16 b */
+ uint16_t dst_fid;
+ /* dst_fid is 16 b */
+ uint16_t l2_ctxt_id;
+ /* l2_ctxt_id is 16 b */
+ uint64_t em_info;
+ /* em_info is 64 b */
+ uint64_t tcam_info;
+ /* tcam_info is 64 b */
+ uint64_t vfp_tcam_info;
+ /* vfp_tcam_info is 64 b */
+ uint16_t ar_id;
+ /* ar_id is 16 b */
+ uint16_t flow_handle;
+ /* flow_handle is 16 b */
+ uint32_t tunnel_handle;
+ /* tunnel_handle is 32 b */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
/*
- * When this bit is '1', Reception of rx pause messages is
- * supported. Disabled otherwise.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_RX \
- UINT32_C(0x2)
- uint16_t adv_eee_link_speed_mask;
+} __attribute__((packed));
+
+/* hwrm_cfa_flow_flush */
+/* Description: All flows are removed from table and resources are released. */
+/* Input (24 bytes) */
+struct hwrm_cfa_flow_flush_input {
+ uint16_t req_type;
/*
- * Current setting for link speed mask that is used to advertise
- * speeds during autonegotiation when EEE is enabled. This field
- * is valid only when eee_enabled flags is set to 1. The speeds
- * specified in this field shall be a subset of speeds specified
- * in auto_link_speed_mask.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- /* Reserved */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
- UINT32_C(0x1)
- /* 100Mb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_100MB \
- UINT32_C(0x2)
- /* Reserved */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
- UINT32_C(0x4)
- /* 1Gb link speed (Full-duplex) */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_1GB \
- UINT32_C(0x8)
- /* Reserved */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
- UINT32_C(0x10)
- /* Reserved */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
- UINT32_C(0x20)
- /* 10Gb link speed */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_10GB \
- UINT32_C(0x40)
- uint16_t link_partner_adv_eee_link_speed_mask;
+ uint16_t cmpl_ring;
/*
- * Current setting for link speed mask that is advertised by the
- * link partner when EEE is enabled. This field is valid only
- * when eee_enabled flags is set to 1.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- /* Reserved */
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
- UINT32_C(0x1)
- /* 100Mb link speed (Full-duplex) */
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_100MB \
- UINT32_C(0x2)
- /* Reserved */
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
- UINT32_C(0x4)
- /* 1Gb link speed (Full-duplex) */
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_1GB \
- UINT32_C(0x8)
- /* Reserved */
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
- UINT32_C(0x10)
- /* Reserved */
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
- UINT32_C(0x20)
- /* 10Gb link speed */
- #define \
- HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_10GB \
- UINT32_C(0x40)
- uint32_t xcvr_identifier_type_tx_lpi_timer;
- /* This value represents transceiver identifier type. */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * Current setting of TX LPI timer in microseconds. This field
- * is valid only when_eee_enabled flag is set to 1 and
- * tx_lpi_enabled is set to 1.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_MASK UINT32_C(0xffffff)
- #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_SFT 0
- /* This value represents transceiver identifier type. */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_MASK \
- UINT32_C(0xff000000)
- #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFT 24
- /* Unknown */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_UNKNOWN \
- (UINT32_C(0x0) << 24)
- /* SFP/SFP+/SFP28 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFP \
- (UINT32_C(0x3) << 24)
- /* QSFP */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP \
- (UINT32_C(0xc) << 24)
- /* QSFP+ */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFPPLUS \
- (UINT32_C(0xd) << 24)
- /* QSFP28 */
- #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28 \
- (UINT32_C(0x11) << 24)
- uint16_t fec_cfg;
+ uint64_t resp_addr;
/*
- * This value represents the current configuration of Forward
- * Error Correction (FEC) on the port.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
+ uint32_t flags;
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_flow_flush_output {
+ uint16_t error_code;
/*
- * When set to 1, then FEC is not supported on this port. If
- * this flag is set to 1, then all other FEC configuration flags
- * shall be ignored. When set to 0, then FEC is supported as
- * indicated by other configuration flags. If no cable is
- * attached and the HWRM does not yet know the FEC capability,
- * then the HWRM shall set this flag to 1 when reporting FEC
- * capability.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_NONE_SUPPORTED \
- UINT32_C(0x1)
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * When set to 1, then FEC autonegotiation is supported on this
- * port. When set to 0, then FEC autonegotiation is not
- * supported on this port.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_SUPPORTED \
- UINT32_C(0x2)
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
/*
- * When set to 1, then FEC autonegotiation is enabled on this
- * port. When set to 0, then FEC autonegotiation is disabled if
- * supported. This flag should be ignored if FEC autonegotiation
- * is not supported on this port.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_ENABLED \
- UINT32_C(0x4)
+} __attribute__((packed));
+
+/* hwrm_cfa_flow_stats */
+/* Description: Flow is removed from table and resources are released. */
+/* Input (40 bytes) */
+struct hwrm_cfa_flow_stats_input {
+ uint16_t req_type;
/*
- * When set to 1, then FEC CLAUSE 74 (Fire Code) is supported on
- * this port. When set to 0, then FEC CLAUSE 74 (Fire Code) is
- * not supported on this port.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_SUPPORTED \
- UINT32_C(0x8)
+ uint16_t cmpl_ring;
/*
- * When set to 1, then FEC CLAUSE 74 (Fire Code) is enabled on
- * this port. When set to 0, then FEC CLAUSE 74 (Fire Code) is
- * disabled if supported. This flag should be ignored if FEC
- * CLAUSE 74 is not supported on this port.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_ENABLED \
- UINT32_C(0x10)
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is supported
- * on this port. When set to 0, then FEC CLAUSE 91 (Reed
- * Solomon) is not supported on this port.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_SUPPORTED \
- UINT32_C(0x20)
+ uint64_t resp_addr;
/*
- * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is enabled
- * on this port. When set to 0, then FEC CLAUSE 91 (Reed
- * Solomon) is disabled if supported. This flag should be
- * ignored if FEC CLAUSE 91 is not supported on this port.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_ENABLED \
- UINT32_C(0x40)
- uint8_t unused_1;
- uint8_t unused_2;
- char phy_vendor_name[16];
+ uint16_t num_flows;
+ /* Flow handle. */
+ uint16_t flow_handle_0;
+ /* Flow handle. */
+ uint16_t flow_handle_1;
+ /* Flow handle. */
+ uint16_t flow_handle_2;
+ /* Flow handle. */
+ uint16_t flow_handle_3;
+ /* Flow handle. */
+ uint16_t flow_handle_4;
+ /* Flow handle. */
+ uint16_t flow_handle_5;
+ /* Flow handle. */
+ uint16_t flow_handle_6;
+ /* Flow handle. */
+ uint16_t flow_handle_7;
+ /* Flow handle. */
+ uint16_t flow_handle_8;
+ /* Flow handle. */
+ uint16_t flow_handle_9;
+ /* Flow handle. */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (176 bytes) */
+struct hwrm_cfa_flow_stats_output {
+ uint16_t error_code;
/*
- * Up to 16 bytes of null padded ASCII string representing PHY
- * vendor. If the string is set to null, then the vendor name is
- * not available.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- char phy_vendor_partnumber[16];
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * Up to 16 bytes of null padded ASCII string that identifies
- * vendor specific part number of the PHY. If the string is set
- * to null, then the vendor specific part number is not
- * available.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- uint32_t unused_3;
- uint8_t unused_4;
- uint8_t unused_5;
- uint8_t unused_6;
+ uint64_t packet_0;
+ /* packet_0 is 64 b */
+ uint64_t packet_1;
+ /* packet_1 is 64 b */
+ uint64_t packet_2;
+ /* packet_2 is 64 b */
+ uint64_t packet_3;
+ /* packet_3 is 64 b */
+ uint64_t packet_4;
+ /* packet_4 is 64 b */
+ uint64_t packet_5;
+ /* packet_5 is 64 b */
+ uint64_t packet_6;
+ /* packet_6 is 64 b */
+ uint64_t packet_7;
+ /* packet_7 is 64 b */
+ uint64_t packet_8;
+ /* packet_8 is 64 b */
+ uint64_t packet_9;
+ /* packet_9 is 64 b */
+ uint64_t byte_0;
+ /* byte_0 is 64 b */
+ uint64_t byte_1;
+ /* byte_1 is 64 b */
+ uint64_t byte_2;
+ /* byte_2 is 64 b */
+ uint64_t byte_3;
+ /* byte_3 is 64 b */
+ uint64_t byte_4;
+ /* byte_4 is 64 b */
+ uint64_t byte_5;
+ /* byte_5 is 64 b */
+ uint64_t byte_6;
+ /* byte_6 is 64 b */
+ uint64_t byte_7;
+ /* byte_7 is 64 b */
+ uint64_t byte_8;
+ /* byte_8 is 64 b */
+ uint64_t byte_9;
+ /* byte_9 is 64 b */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -5609,10 +23028,10 @@ struct hwrm_port_phy_qcfg_output {
*/
} __attribute__((packed));
-/* hwrm_port_qstats */
-/* Description: This function returns per port Ethernet statistics. */
-/* Input (40 bytes) */
-struct hwrm_port_qstats_input {
+/* hwrm_cfa_vf_pair_alloc */
+/* Description: VF pair is added to table and resources are allocated. */
+/* Input (32 bytes) */
+struct hwrm_cfa_vf_pair_alloc_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -5639,20 +23058,17 @@ struct hwrm_port_qstats_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t port_id;
- /* Port ID of port that is being queried. */
- uint8_t unused_0;
- uint8_t unused_1;
- uint8_t unused_2[3];
- uint8_t unused_3;
- uint64_t tx_stat_host_addr;
- /* This is the host address where Tx port statistics will be stored */
- uint64_t rx_stat_host_addr;
- /* This is the host address where Rx port statistics will be stored */
+ uint16_t vf_a_id;
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint16_t vf_b_id;
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint32_t unused_0;
+ char pair_name[32];
+ /* VF Pair name (32 byte string). */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_port_qstats_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_vf_pair_alloc_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -5668,13 +23084,10 @@ struct hwrm_port_qstats_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint16_t tx_stat_size;
- /* The size of TX port statistics block in bytes. */
- uint16_t rx_stat_size;
- /* The size of RX port statistics block in bytes. */
- uint8_t unused_0;
+ uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -5686,15 +23099,10 @@ struct hwrm_port_qstats_output {
*/
} __attribute__((packed));
-/* hwrm_port_clr_stats */
-/*
- * Description: This function clears per port statistics. The HWRM shall not
- * allow a VF driver to clear port statistics. The HWRM shall not allow a PF
- * driver to clear port statistics in a partitioning mode. The HWRM may allow a
- * PF driver to clear port statistics in the non-partitioning mode.
- */
-/* Input (24 bytes) */
-struct hwrm_port_clr_stats_input {
+/* hwrm_cfa_vf_pair_free */
+/* Description: VF Pair is removed from table and resources are released. */
+/* Input (24 bytes) */
+struct hwrm_cfa_vf_pair_free_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -5721,13 +23129,12 @@ struct hwrm_port_clr_stats_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t port_id;
- /* Port ID of port that is being queried. */
- uint16_t unused_0[3];
+ char pair_name[32];
+ /* VF Pair name (32 byte string). */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_port_clr_stats_output {
+/* Output (16 bytes) */
+struct hwrm_cfa_vf_pair_free_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -5758,15 +23165,10 @@ struct hwrm_port_clr_stats_output {
*/
} __attribute__((packed));
-/* hwrm_port_led_cfg */
-/*
- * Description: This function is used to configure LEDs on a given port. Each
- * port has individual set of LEDs associated with it. These LEDs are used for
- * speed/link configuration as well as activity indicator configuration. Up to
- * three LEDs can be configured, one for activity and two for speeds.
- */
-/* Input (64 bytes) */
-struct hwrm_port_led_cfg_input {
+/* hwrm_cfa_vf_pair_info */
+/* Description: VF pair information is returned. */
+/* Input (32 bytes) */
+struct hwrm_cfa_vf_pair_info_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -5781,305 +23183,31 @@ struct hwrm_port_led_cfg_input {
*/
uint16_t seq_id;
/* This value indicates the command sequence number. */
- uint16_t target_id;
- /*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function
- * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
- * - HWRM
- */
- uint64_t resp_addr;
- /*
- * This is the host address where the response will be written
- * when the request is complete. This area must be 16B aligned
- * and must be cleared to zero before the request is made.
- */
- uint32_t enables;
- /* This bit must be '1' for the led0_id field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_ID UINT32_C(0x1)
- /* This bit must be '1' for the led0_state field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_STATE UINT32_C(0x2)
- /* This bit must be '1' for the led0_color field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_COLOR UINT32_C(0x4)
- /*
- * This bit must be '1' for the led0_blink_on field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_BLINK_ON UINT32_C(0x8)
- /*
- * This bit must be '1' for the led0_blink_off field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_BLINK_OFF UINT32_C(0x10)
- /*
- * This bit must be '1' for the led0_group_id field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_GROUP_ID UINT32_C(0x20)
- /* This bit must be '1' for the led1_id field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_ID UINT32_C(0x40)
- /* This bit must be '1' for the led1_state field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_STATE UINT32_C(0x80)
- /* This bit must be '1' for the led1_color field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_COLOR UINT32_C(0x100)
- /*
- * This bit must be '1' for the led1_blink_on field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_BLINK_ON UINT32_C(0x200)
- /*
- * This bit must be '1' for the led1_blink_off field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_BLINK_OFF UINT32_C(0x400)
- /*
- * This bit must be '1' for the led1_group_id field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_GROUP_ID UINT32_C(0x800)
- /* This bit must be '1' for the led2_id field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_ID UINT32_C(0x1000)
- /* This bit must be '1' for the led2_state field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_STATE UINT32_C(0x2000)
- /* This bit must be '1' for the led2_color field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_COLOR UINT32_C(0x4000)
- /*
- * This bit must be '1' for the led2_blink_on field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_BLINK_ON UINT32_C(0x8000)
- /*
- * This bit must be '1' for the led2_blink_off field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_BLINK_OFF UINT32_C(0x10000)
- /*
- * This bit must be '1' for the led2_group_id field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_GROUP_ID UINT32_C(0x20000)
- /* This bit must be '1' for the led3_id field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_ID UINT32_C(0x40000)
- /* This bit must be '1' for the led3_state field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_STATE UINT32_C(0x80000)
- /* This bit must be '1' for the led3_color field to be configured. */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_COLOR UINT32_C(0x100000)
- /*
- * This bit must be '1' for the led3_blink_on field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_BLINK_ON UINT32_C(0x200000)
- /*
- * This bit must be '1' for the led3_blink_off field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_BLINK_OFF \
- UINT32_C(0x400000)
- /*
- * This bit must be '1' for the led3_group_id field to be
- * configured.
- */
- #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_GROUP_ID UINT32_C(0x800000)
- uint16_t port_id;
- /* Port ID of port whose LEDs are configured. */
- uint8_t num_leds;
- /*
- * The number of LEDs that are being configured. Up to 4 LEDs
- * can be configured with this command.
- */
- uint8_t rsvd;
- /* Reserved field. */
- uint8_t led0_id;
- /* An identifier for the LED #0. */
- uint8_t led0_state;
- /* The requested state of the LED #0. */
- /* Default state of the LED */
- #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_DEFAULT UINT32_C(0x0)
- /* Off */
- #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_OFF UINT32_C(0x1)
- /* On */
- #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_ON UINT32_C(0x2)
- /* Blink */
- #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINK UINT32_C(0x3)
- /* Blink Alternately */
- #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINKALT UINT32_C(0x4)
- uint8_t led0_color;
- /* The requested color of LED #0. */
- /* Default */
- #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_DEFAULT UINT32_C(0x0)
- /* Amber */
- #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_AMBER UINT32_C(0x1)
- /* Green */
- #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREEN UINT32_C(0x2)
- /* Green or Amber */
- #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREENAMBER UINT32_C(0x3)
- uint8_t unused_0;
- uint16_t led0_blink_on;
- /*
- * If the LED #0 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED on
- * between cycles.
- */
- uint16_t led0_blink_off;
- /*
- * If the LED #0 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED off
- * between cycles.
- */
- uint8_t led0_group_id;
- /*
- * An identifier for the group of LEDs that LED #0 belongs to.
- * If set to 0, then the LED #0 shall not be grouped and shall
- * be treated as an individual resource. For all other non-zero
- * values of this field, LED #0 shall be grouped together with
- * the LEDs with the same group ID value.
- */
- uint8_t rsvd0;
- /* Reserved field. */
- uint8_t led1_id;
- /* An identifier for the LED #1. */
- uint8_t led1_state;
- /* The requested state of the LED #1. */
- /* Default state of the LED */
- #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_DEFAULT UINT32_C(0x0)
- /* Off */
- #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_OFF UINT32_C(0x1)
- /* On */
- #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_ON UINT32_C(0x2)
- /* Blink */
- #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINK UINT32_C(0x3)
- /* Blink Alternately */
- #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINKALT UINT32_C(0x4)
- uint8_t led1_color;
- /* The requested color of LED #1. */
- /* Default */
- #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_DEFAULT UINT32_C(0x0)
- /* Amber */
- #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_AMBER UINT32_C(0x1)
- /* Green */
- #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREEN UINT32_C(0x2)
- /* Green or Amber */
- #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREENAMBER UINT32_C(0x3)
- uint8_t unused_1;
- uint16_t led1_blink_on;
- /*
- * If the LED #1 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED on
- * between cycles.
- */
- uint16_t led1_blink_off;
- /*
- * If the LED #1 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED off
- * between cycles.
- */
- uint8_t led1_group_id;
- /*
- * An identifier for the group of LEDs that LED #1 belongs to.
- * If set to 0, then the LED #1 shall not be grouped and shall
- * be treated as an individual resource. For all other non-zero
- * values of this field, LED #1 shall be grouped together with
- * the LEDs with the same group ID value.
- */
- uint8_t rsvd1;
- /* Reserved field. */
- uint8_t led2_id;
- /* An identifier for the LED #2. */
- uint8_t led2_state;
- /* The requested state of the LED #2. */
- /* Default state of the LED */
- #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_DEFAULT UINT32_C(0x0)
- /* Off */
- #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_OFF UINT32_C(0x1)
- /* On */
- #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_ON UINT32_C(0x2)
- /* Blink */
- #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINK UINT32_C(0x3)
- /* Blink Alternately */
- #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINKALT UINT32_C(0x4)
- uint8_t led2_color;
- /* The requested color of LED #2. */
- /* Default */
- #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_DEFAULT UINT32_C(0x0)
- /* Amber */
- #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_AMBER UINT32_C(0x1)
- /* Green */
- #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREEN UINT32_C(0x2)
- /* Green or Amber */
- #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREENAMBER UINT32_C(0x3)
- uint8_t unused_2;
- uint16_t led2_blink_on;
- /*
- * If the LED #2 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED on
- * between cycles.
- */
- uint16_t led2_blink_off;
- /*
- * If the LED #2 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED off
- * between cycles.
- */
- uint8_t led2_group_id;
- /*
- * An identifier for the group of LEDs that LED #2 belongs to.
- * If set to 0, then the LED #2 shall not be grouped and shall
- * be treated as an individual resource. For all other non-zero
- * values of this field, LED #2 shall be grouped together with
- * the LEDs with the same group ID value.
- */
- uint8_t rsvd2;
- /* Reserved field. */
- uint8_t led3_id;
- /* An identifier for the LED #3. */
- uint8_t led3_state;
- /* The requested state of the LED #3. */
- /* Default state of the LED */
- #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_DEFAULT UINT32_C(0x0)
- /* Off */
- #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_OFF UINT32_C(0x1)
- /* On */
- #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_ON UINT32_C(0x2)
- /* Blink */
- #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINK UINT32_C(0x3)
- /* Blink Alternately */
- #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINKALT UINT32_C(0x4)
- uint8_t led3_color;
- /* The requested color of LED #3. */
- /* Default */
- #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_DEFAULT UINT32_C(0x0)
- /* Amber */
- #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_AMBER UINT32_C(0x1)
- /* Green */
- #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREEN UINT32_C(0x2)
- /* Green or Amber */
- #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREENAMBER UINT32_C(0x3)
- uint8_t unused_3;
- uint16_t led3_blink_on;
- /*
- * If the LED #3 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED on
- * between cycles.
- */
- uint16_t led3_blink_off;
- /*
- * If the LED #3 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED off
- * between cycles.
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint8_t led3_group_id;
+ uint64_t resp_addr;
/*
- * An identifier for the group of LEDs that LED #3 belongs to.
- * If set to 0, then the LED #3 shall not be grouped and shall
- * be treated as an individual resource. For all other non-zero
- * values of this field, LED #3 shall be grouped together with
- * the LEDs with the same group ID value.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint8_t rsvd3;
- /* Reserved field. */
+ uint32_t flags;
+ /* If this flag is set, lookup by name else lookup by index. */
+ #define HWRM_CFA_VF_PAIR_INFO_INPUT_FLAGS_LOOKUP_TYPE 0x1UL
+ uint16_t vf_pair_index;
+ /* vf pair table index. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ char vf_pair_name[32];
+ /* VF Pair name (32 byte string). */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_port_led_cfg_output {
+/* Output (64 bytes) */
+struct hwrm_cfa_vf_pair_info_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -6095,10 +23223,30 @@ struct hwrm_port_led_cfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t unused_0;
- uint8_t unused_1;
- uint8_t unused_2;
+ uint16_t next_vf_pair_index;
+ /* vf pair table index. */
+ uint16_t vf_a_fid;
+ /* vf pair member a's vf_fid. */
+ uint16_t vf_a_index;
+ /* vf pair member a's Linux logical VF number. */
+ uint16_t vf_b_fid;
+ /* vf pair member b's vf_fid. */
+ uint16_t vf_b_index;
+ /* vf pair member a's Linux logical VF number. */
+ uint8_t pair_state;
+ /* vf pair state. */
+ /* Pair has been allocated */
+ #define HWRM_CFA_VF_PAIR_INFO_OUTPUT_PAIR_STATE_ALLOCATED 0x1UL
+ /* Both pair members are active */
+ #define HWRM_CFA_VF_PAIR_INFO_OUTPUT_PAIR_STATE_ACTIVE 0x2UL
+ uint8_t unused_0;
+ uint32_t unused_1;
+ char pair_name[32];
+ /* VF Pair name (32 byte string). */
+ uint32_t unused_2;
uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -6110,16 +23258,10 @@ struct hwrm_port_led_cfg_output {
*/
} __attribute__((packed));
-/* hwrm_port_led_qcfg */
-/*
- * Description: This function is used to query configuration of LEDs on a given
- * port. Each port has individual set of LEDs associated with it. These LEDs are
- * used for speed/link configuration as well as activity indicator
- * configuration. Up to three LEDs can be configured, one for activity and two
- * for speeds.
- */
-/* Input (24 bytes) */
-struct hwrm_port_led_qcfg_input {
+/* hwrm_cfa_pair_alloc */
+/* Description: Pair is added to table and resources are allocated. */
+/* Input (40 bytes) */
+struct hwrm_cfa_pair_alloc_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -6146,13 +23288,50 @@ struct hwrm_port_led_qcfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t port_id;
- /* Port ID of port whose LED configuration is being queried. */
- uint16_t unused_0[3];
+ uint8_t pair_mode;
+ /* Pair mode (0-vf2fn, 1-rep2fn, 2-rep2rep, 3-proxy, 4-pfpair). */
+ /*
+ * Pair between VF on local host with PF or VF
+ * on specified host.
+ */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_VF2FN 0x0UL
+ /*
+ * Pair between REP on local host with PF or VF
+ * on specified host.
+ */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2FN 0x1UL
+ /*
+ * Pair between REP on local host with REP on
+ * specified host.
+ */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2REP 0x2UL
+ /* Pair for the proxy interface. */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_PROXY 0x3UL
+ /* Pair for the PF interface. */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_PFPAIR 0x4UL
+ uint8_t unused_0;
+ uint16_t vf_a_id;
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint8_t host_b_id;
+ /* Logical Host (0xff-local host). */
+ uint8_t pf_b_id;
+ /* Logical PF (0xff-PF for command channel). */
+ uint16_t vf_b_id;
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint8_t port_id;
+ /* Loopback port (0xff-internal loopback), valid for mode-3. */
+ uint8_t pri;
+ /* Priority used for encap of loopback packets valid for mode-3. */
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3[3];
+ uint8_t unused_4;
+ char pair_name[32];
+ /* VF Pair name (32 byte string). */
} __attribute__((packed));
-/* Output (56 bytes) */
-struct hwrm_port_led_qcfg_output {
+/* Output (24 bytes) */
+struct hwrm_cfa_pair_alloc_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -6168,224 +23347,84 @@ struct hwrm_port_led_qcfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint8_t num_leds;
+ uint16_t rx_cfa_code_a;
+ /* Only valid for modes 1 and 2. */
+ uint16_t tx_cfa_action_a;
+ /* Only valid for modes 1 and 2. */
+ uint16_t rx_cfa_code_b;
+ /* Only valid for mode 2. */
+ uint16_t tx_cfa_action_b;
+ /* Only valid for mode 2. */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
/*
- * The number of LEDs that are configured on this port. Up to 4
- * LEDs can be returned in the response.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- uint8_t led0_id;
- /* An identifier for the LED #0. */
- uint8_t led0_type;
- /* The type of LED #0. */
- /* Speed LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_SPEED UINT32_C(0x0)
- /* Activity LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_ACTIVITY UINT32_C(0x1)
- /* Invalid */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_INVALID UINT32_C(0xff)
- uint8_t led0_state;
- /* The current state of the LED #0. */
- /* Default state of the LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_DEFAULT UINT32_C(0x0)
- /* Off */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_OFF UINT32_C(0x1)
- /* On */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_ON UINT32_C(0x2)
- /* Blink */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINK UINT32_C(0x3)
- /* Blink Alternately */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINKALT UINT32_C(0x4)
- uint8_t led0_color;
- /* The color of LED #0. */
- /* Default */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_DEFAULT UINT32_C(0x0)
- /* Amber */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_AMBER UINT32_C(0x1)
- /* Green */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREEN UINT32_C(0x2)
- /* Green or Amber */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREENAMBER UINT32_C(0x3)
- uint8_t unused_0;
- uint16_t led0_blink_on;
+} __attribute__((packed));
+
+/* hwrm_cfa_pair_free */
+/* Description: Pair is removed from table and resources are released. */
+/* Input (24 bytes) */
+struct hwrm_cfa_pair_free_input {
+ uint16_t req_type;
/*
- * If the LED #0 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED on
- * between cycles.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- uint16_t led0_blink_off;
+ uint16_t cmpl_ring;
/*
- * If the LED #0 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED off
- * between cycles.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- uint8_t led0_group_id;
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * An identifier for the group of LEDs that LED #0 belongs to.
- * If set to 0, then the LED #0 is not grouped. For all other
- * non-zero values of this field, LED #0 is grouped together
- * with the LEDs with the same group ID value.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint8_t led1_id;
- /* An identifier for the LED #1. */
- uint8_t led1_type;
- /* The type of LED #1. */
- /* Speed LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_SPEED UINT32_C(0x0)
- /* Activity LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_ACTIVITY UINT32_C(0x1)
- /* Invalid */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_INVALID UINT32_C(0xff)
- uint8_t led1_state;
- /* The current state of the LED #1. */
- /* Default state of the LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_DEFAULT UINT32_C(0x0)
- /* Off */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_OFF UINT32_C(0x1)
- /* On */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_ON UINT32_C(0x2)
- /* Blink */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINK UINT32_C(0x3)
- /* Blink Alternately */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINKALT UINT32_C(0x4)
- uint8_t led1_color;
- /* The color of LED #1. */
- /* Default */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_DEFAULT UINT32_C(0x0)
- /* Amber */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_AMBER UINT32_C(0x1)
- /* Green */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREEN UINT32_C(0x2)
- /* Green or Amber */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREENAMBER UINT32_C(0x3)
- uint8_t unused_1;
- uint16_t led1_blink_on;
+ uint64_t resp_addr;
/*
- * If the LED #1 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED on
- * between cycles.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint16_t led1_blink_off;
+ char pair_name[32];
+ /* VF Pair name (32 byte string). */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_pair_free_output {
+ uint16_t error_code;
/*
- * If the LED #1 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED off
- * between cycles.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- uint8_t led1_group_id;
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * An identifier for the group of LEDs that LED #1 belongs to.
- * If set to 0, then the LED #1 is not grouped. For all other
- * non-zero values of this field, LED #1 is grouped together
- * with the LEDs with the same group ID value.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- uint8_t led2_id;
- /* An identifier for the LED #2. */
- uint8_t led2_type;
- /* The type of LED #2. */
- /* Speed LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_SPEED UINT32_C(0x0)
- /* Activity LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_ACTIVITY UINT32_C(0x1)
- /* Invalid */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_INVALID UINT32_C(0xff)
- uint8_t led2_state;
- /* The current state of the LED #2. */
- /* Default state of the LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_DEFAULT UINT32_C(0x0)
- /* Off */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_OFF UINT32_C(0x1)
- /* On */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_ON UINT32_C(0x2)
- /* Blink */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINK UINT32_C(0x3)
- /* Blink Alternately */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINKALT UINT32_C(0x4)
- uint8_t led2_color;
- /* The color of LED #2. */
- /* Default */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_DEFAULT UINT32_C(0x0)
- /* Amber */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_AMBER UINT32_C(0x1)
- /* Green */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREEN UINT32_C(0x2)
- /* Green or Amber */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREENAMBER UINT32_C(0x3)
+ uint32_t unused_0;
+ uint8_t unused_1;
uint8_t unused_2;
- uint16_t led2_blink_on;
- /*
- * If the LED #2 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED on
- * between cycles.
- */
- uint16_t led2_blink_off;
- /*
- * If the LED #2 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED off
- * between cycles.
- */
- uint8_t led2_group_id;
- /*
- * An identifier for the group of LEDs that LED #2 belongs to.
- * If set to 0, then the LED #2 is not grouped. For all other
- * non-zero values of this field, LED #2 is grouped together
- * with the LEDs with the same group ID value.
- */
- uint8_t led3_id;
- /* An identifier for the LED #3. */
- uint8_t led3_type;
- /* The type of LED #3. */
- /* Speed LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_SPEED UINT32_C(0x0)
- /* Activity LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_ACTIVITY UINT32_C(0x1)
- /* Invalid */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_INVALID UINT32_C(0xff)
- uint8_t led3_state;
- /* The current state of the LED #3. */
- /* Default state of the LED */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_DEFAULT UINT32_C(0x0)
- /* Off */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_OFF UINT32_C(0x1)
- /* On */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_ON UINT32_C(0x2)
- /* Blink */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINK UINT32_C(0x3)
- /* Blink Alternately */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINKALT UINT32_C(0x4)
- uint8_t led3_color;
- /* The color of LED #3. */
- /* Default */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_DEFAULT UINT32_C(0x0)
- /* Amber */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_AMBER UINT32_C(0x1)
- /* Green */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREEN UINT32_C(0x2)
- /* Green or Amber */
- #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREENAMBER UINT32_C(0x3)
uint8_t unused_3;
- uint16_t led3_blink_on;
- /*
- * If the LED #3 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED on
- * between cycles.
- */
- uint16_t led3_blink_off;
- /*
- * If the LED #3 state is "blink" or "blinkalt", then this field
- * represents the requested time in milliseconds to keep LED off
- * between cycles.
- */
- uint8_t led3_group_id;
- /*
- * An identifier for the group of LEDs that LED #3 belongs to.
- * If set to 0, then the LED #3 is not grouped. For all other
- * non-zero values of this field, LED #3 is grouped together
- * with the LEDs with the same group ID value.
- */
- uint8_t unused_4;
- uint16_t unused_5;
- uint8_t unused_6;
- uint8_t unused_7;
- uint8_t unused_8;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -6397,15 +23436,10 @@ struct hwrm_port_led_qcfg_output {
*/
} __attribute__((packed));
-/* hwrm_port_led_qcaps */
-/*
- * Description: This function is used to query capabilities of LEDs on a given
- * port. Each port has individual set of LEDs associated with it. These LEDs are
- * used for speed/link configuration as well as activity indicator
- * configuration.
- */
-/* Input (24 bytes) */
-struct hwrm_port_led_qcaps_input {
+/* hwrm_cfa_pair_info */
+/* Description: Pair information is returned. */
+/* Input (32 bytes) */
+struct hwrm_cfa_pair_info_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -6432,13 +23466,23 @@ struct hwrm_port_led_qcaps_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t port_id;
- /* Port ID of port whose LED configuration is being queried. */
- uint16_t unused_0[3];
+ uint32_t flags;
+ /* If this flag is set, lookup by name else lookup by index. */
+ #define HWRM_CFA_PAIR_INFO_INPUT_FLAGS_LOOKUP_TYPE 0x1UL
+ /* If this flag is set, lookup by PF id and VF id. */
+ #define HWRM_CFA_PAIR_INFO_INPUT_FLAGS_LOOKUP_REPRE 0x2UL
+ uint16_t pair_index;
+ /* Pair table index. */
+ uint8_t pair_pfid;
+ /* Pair pf index. */
+ uint8_t pair_vfid;
+ /* Pair vf index. */
+ char pair_name[32];
+ /* Pair name (32 byte string). */
} __attribute__((packed));
-/* Output (48 bytes) */
-struct hwrm_port_led_qcaps_output {
+/* Output (72 bytes) */
+struct hwrm_cfa_pair_info_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -6454,276 +23498,298 @@ struct hwrm_port_led_qcaps_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint8_t num_leds;
- /*
- * The number of LEDs that are configured on this port. Up to 4
- * LEDs can be returned in the response.
- */
- uint8_t unused_0[3];
- /* Reserved for future use. */
- uint8_t led0_id;
- /* An identifier for the LED #0. */
- uint8_t led0_type;
- /* The type of LED #0. */
- /* Speed LED */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_SPEED UINT32_C(0x0)
- /* Activity LED */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_ACTIVITY UINT32_C(0x1)
- /* Invalid */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_INVALID UINT32_C(0xff)
- uint8_t led0_group_id;
- /*
- * An identifier for the group of LEDs that LED #0 belongs to.
- * If set to 0, then the LED #0 cannot be grouped. For all other
- * non-zero values of this field, LED #0 is grouped together
- * with the LEDs with the same group ID value.
- */
+ uint16_t next_pair_index;
+ /* Pair table index. */
+ uint16_t a_fid;
+ /* Pair member a's fid. */
+ uint8_t host_a_index;
+ /* Logical host number. */
+ uint8_t pf_a_index;
+ /* Logical PF number. */
+ uint16_t vf_a_index;
+ /* Pair member a's Linux logical VF number. */
+ uint16_t rx_cfa_code_a;
+ /* Rx CFA code. */
+ uint16_t tx_cfa_action_a;
+ /* Tx CFA action. */
+ uint16_t b_fid;
+ /* Pair member b's fid. */
+ uint8_t host_b_index;
+ /* Logical host number. */
+ uint8_t pf_b_index;
+ /* Logical PF number. */
+ uint16_t vf_b_index;
+ /* Pair member a's Linux logical VF number. */
+ uint16_t rx_cfa_code_b;
+ /* Rx CFA code. */
+ uint16_t tx_cfa_action_b;
+ /* Tx CFA action. */
+ uint8_t pair_mode;
+ /* Pair mode (0-vf2fn, 1-rep2fn, 2-rep2rep, 3-proxy, 4-pfpair). */
+ /*
+ * Pair between VF on local host with PF or VF
+ * on specified host.
+ */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_VF2FN 0x0UL
+ /*
+ * Pair between REP on local host with PF or VF
+ * on specified host.
+ */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_REP2FN 0x1UL
+ /*
+ * Pair between REP on local host with REP on
+ * specified host.
+ */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_REP2REP 0x2UL
+ /* Pair for the proxy interface. */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_PROXY 0x3UL
+ /* Pair for the PF interface. */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_PFPAIR 0x4UL
+ uint8_t pair_state;
+ /* Pair state. */
+ /* Pair has been allocated */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_STATE_ALLOCATED 0x1UL
+ /* Both pair members are active */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_STATE_ACTIVE 0x2UL
+ char pair_name[32];
+ /* Pair name (32 byte string). */
+ uint32_t unused_0;
uint8_t unused_1;
- uint16_t led0_state_caps;
- /* The states supported by LED #0. */
- /*
- * If set to 1, this LED is enabled. If set to 0, this LED is
- * disabled.
- */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_ENABLED UINT32_C(0x1)
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
/*
- * If set to 1, off state is supported on this LED. If set to 0,
- * off state is not supported on this LED.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_OFF_SUPPORTED \
- UINT32_C(0x2)
+} __attribute__((packed));
+
+/* hwrm_cfa_vfr_alloc */
+/* Description: VF-R is added to table and resources are allocated. */
+/* Input (32 bytes) */
+struct hwrm_cfa_vfr_alloc_input {
+ uint16_t req_type;
/*
- * If set to 1, on state is supported on this LED. If set to 0,
- * on state is not supported on this LED.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_ON_SUPPORTED \
- UINT32_C(0x4)
+ uint16_t cmpl_ring;
/*
- * If set to 1, blink state is supported on this LED. If set to
- * 0, blink state is not supported on this LED.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_BLINK_SUPPORTED \
- UINT32_C(0x8)
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * If set to 1, blink_alt state is supported on this LED. If set
- * to 0, blink_alt state is not supported on this LED.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_BLINK_ALT_SUPPORTED \
- UINT32_C(0x10)
- uint16_t led0_color_caps;
- /* The colors supported by LED #0. */
- /* reserved */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_RSVD UINT32_C(0x1)
+ uint64_t resp_addr;
/*
- * If set to 1, Amber color is supported on this LED. If set to
- * 0, Amber color is not supported on this LED.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_AMBER_SUPPORTED \
- UINT32_C(0x2)
+ uint16_t vf_id;
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint16_t reserved;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t unused_0;
+ char vfr_name[32];
+ /* VF Representor name (32 byte string). */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_vfr_alloc_output {
+ uint16_t error_code;
/*
- * If set to 1, Green color is supported on this LED. If set to
- * 0, Green color is not supported on this LED.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_GREEN_SUPPORTED \
- UINT32_C(0x4)
- uint8_t led1_id;
- /* An identifier for the LED #1. */
- uint8_t led1_type;
- /* The type of LED #1. */
- /* Speed LED */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_SPEED UINT32_C(0x0)
- /* Activity LED */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_ACTIVITY UINT32_C(0x1)
- /* Invalid */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_INVALID UINT32_C(0xff)
- uint8_t led1_group_id;
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * An identifier for the group of LEDs that LED #1 belongs to.
- * If set to 0, then the LED #0 cannot be grouped. For all other
- * non-zero values of this field, LED #0 is grouped together
- * with the LEDs with the same group ID value.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
+ uint16_t rx_cfa_code;
+ /* Rx CFA code. */
+ uint16_t tx_cfa_action;
+ /* Tx CFA action. */
+ uint8_t unused_0;
+ uint8_t unused_1;
uint8_t unused_2;
- uint16_t led1_state_caps;
- /* The states supported by LED #1. */
- /*
- * If set to 1, this LED is enabled. If set to 0, this LED is
- * disabled.
- */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_ENABLED UINT32_C(0x1)
+ uint8_t valid;
/*
- * If set to 1, off state is supported on this LED. If set to 0,
- * off state is not supported on this LED.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_OFF_SUPPORTED \
- UINT32_C(0x2)
+} __attribute__((packed));
+
+/* hwrm_cfa_vfr_free */
+/* Description: VF-R is removed from table and resources are released. */
+/* Input (24 bytes) */
+struct hwrm_cfa_vfr_free_input {
+ uint16_t req_type;
/*
- * If set to 1, on state is supported on this LED. If set to 0,
- * on state is not supported on this LED.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_ON_SUPPORTED \
- UINT32_C(0x4)
+ uint16_t cmpl_ring;
/*
- * If set to 1, blink state is supported on this LED. If set to
- * 0, blink state is not supported on this LED.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_BLINK_SUPPORTED \
- UINT32_C(0x8)
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * If set to 1, blink_alt state is supported on this LED. If set
- * to 0, blink_alt state is not supported on this LED.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_BLINK_ALT_SUPPORTED \
- UINT32_C(0x10)
- uint16_t led1_color_caps;
- /* The colors supported by LED #1. */
- /* reserved */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_RSVD UINT32_C(0x1)
+ uint64_t resp_addr;
/*
- * If set to 1, Amber color is supported on this LED. If set to
- * 0, Amber color is not supported on this LED.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_AMBER_SUPPORTED \
- UINT32_C(0x2)
+ char vfr_name[32];
+ /* VF Representor name (32 byte string). */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_vfr_free_output {
+ uint16_t error_code;
/*
- * If set to 1, Green color is supported on this LED. If set to
- * 0, Green color is not supported on this LED.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_GREEN_SUPPORTED \
- UINT32_C(0x4)
- uint8_t led2_id;
- /* An identifier for the LED #2. */
- uint8_t led2_type;
- /* The type of LED #2. */
- /* Speed LED */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_SPEED UINT32_C(0x0)
- /* Activity LED */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_ACTIVITY UINT32_C(0x1)
- /* Invalid */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_INVALID UINT32_C(0xff)
- uint8_t led2_group_id;
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * An identifier for the group of LEDs that LED #0 belongs to.
- * If set to 0, then the LED #0 cannot be grouped. For all other
- * non-zero values of this field, LED #0 is grouped together
- * with the LEDs with the same group ID value.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
uint8_t unused_3;
- uint16_t led2_state_caps;
- /* The states supported by LED #2. */
- /*
- * If set to 1, this LED is enabled. If set to 0, this LED is
- * disabled.
- */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_ENABLED UINT32_C(0x1)
- /*
- * If set to 1, off state is supported on this LED. If set to 0,
- * off state is not supported on this LED.
- */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_OFF_SUPPORTED \
- UINT32_C(0x2)
- /*
- * If set to 1, on state is supported on this LED. If set to 0,
- * on state is not supported on this LED.
- */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_ON_SUPPORTED \
- UINT32_C(0x4)
- /*
- * If set to 1, blink state is supported on this LED. If set to
- * 0, blink state is not supported on this LED.
- */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_BLINK_SUPPORTED \
- UINT32_C(0x8)
- /*
- * If set to 1, blink_alt state is supported on this LED. If set
- * to 0, blink_alt state is not supported on this LED.
- */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_BLINK_ALT_SUPPORTED \
- UINT32_C(0x10)
- uint16_t led2_color_caps;
- /* The colors supported by LED #2. */
- /* reserved */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_RSVD UINT32_C(0x1)
+ uint8_t valid;
/*
- * If set to 1, Amber color is supported on this LED. If set to
- * 0, Amber color is not supported on this LED.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_AMBER_SUPPORTED \
- UINT32_C(0x2)
+} __attribute__((packed));
+
+/* hwrm_tunnel_dst_port_query */
+/*
+ * Description: This function is called by a driver to query tunnel type
+ * specific destination port configuration.
+ */
+/* Input (24 bytes) */
+struct hwrm_tunnel_dst_port_query_input {
+ uint16_t req_type;
/*
- * If set to 1, Green color is supported on this LED. If set to
- * 0, Green color is not supported on this LED.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_GREEN_SUPPORTED \
- UINT32_C(0x4)
- uint8_t led3_id;
- /* An identifier for the LED #3. */
- uint8_t led3_type;
- /* The type of LED #3. */
- /* Speed LED */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_SPEED UINT32_C(0x0)
- /* Activity LED */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_ACTIVITY UINT32_C(0x1)
- /* Invalid */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_INVALID UINT32_C(0xff)
- uint8_t led3_group_id;
+ uint16_t cmpl_ring;
/*
- * An identifier for the group of LEDs that LED #3 belongs to.
- * If set to 0, then the LED #0 cannot be grouped. For all other
- * non-zero values of this field, LED #0 is grouped together
- * with the LEDs with the same group ID value.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- uint8_t unused_4;
- uint16_t led3_state_caps;
- /* The states supported by LED #3. */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * If set to 1, this LED is enabled. If set to 0, this LED is
- * disabled.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_ENABLED UINT32_C(0x1)
+ uint64_t resp_addr;
/*
- * If set to 1, off state is supported on this LED. If set to 0,
- * off state is not supported on this LED.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_OFF_SUPPORTED \
- UINT32_C(0x2)
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_VXLAN 0x1UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_GENEVE 0x5UL
/*
- * If set to 1, on state is supported on this LED. If set to 0,
- * on state is not supported on this LED.
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_ON_SUPPORTED \
- UINT32_C(0x4)
+ #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_VXLAN_V4 0x9UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_tunnel_dst_port_query_output {
+ uint16_t error_code;
/*
- * If set to 1, blink state is supported on this LED. If set to
- * 0, blink state is not supported on this LED.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_BLINK_SUPPORTED \
- UINT32_C(0x8)
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * If set to 1, blink_alt state is supported on this LED. If set
- * to 0, blink_alt state is not supported on this LED.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_BLINK_ALT_SUPPORTED \
- UINT32_C(0x10)
- uint16_t led3_color_caps;
- /* The colors supported by LED #3. */
- /* reserved */
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_RSVD UINT32_C(0x1)
+ uint16_t tunnel_dst_port_id;
/*
- * If set to 1, Amber color is supported on this LED. If set to
- * 0, Amber color is not supported on this LED.
+ * This field represents the identifier of L4 destination port
+ * used for the given tunnel type. This field is valid for
+ * specific tunnel types that use layer 4 (e.g. UDP) transports
+ * for tunneling.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_AMBER_SUPPORTED \
- UINT32_C(0x2)
+ uint16_t tunnel_dst_port_val;
/*
- * If set to 1, Green color is supported on this LED. If set to
- * 0, Green color is not supported on this LED.
+ * This field represents the value of L4 destination port
+ * identified by tunnel_dst_port_id. This field is valid for
+ * specific tunnel types that use layer 4 (e.g. UDP) transports
+ * for tunneling. This field is in network byte order. A value
+ * of 0 means that the destination port is not configured.
*/
- #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_GREEN_SUPPORTED \
- UINT32_C(0x4)
- uint8_t unused_5;
- uint8_t unused_6;
- uint8_t unused_7;
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -6735,19 +23801,24 @@ struct hwrm_port_led_qcaps_output {
*/
} __attribute__((packed));
-/* hwrm_queue_qportcfg */
+/* hwrm_tunnel_dst_port_alloc */
/*
- * Description: This function is called by a driver to query queue configuration
- * of a port. # The HWRM shall at least advertise one queue with lossy service
- * profile. # The driver shall use this command to query queue ids before
- * configuring or using any queues. # If a service profile is not set for a
- * queue, then the driver shall not use that queue without configuring a service
- * profile for it. # If the driver is not allowed to configure service profiles,
- * then the driver shall only use queues for which service profiles are pre-
- * configured.
+ * Description: This function is called by a driver to allocate l4 destination
+ * port for a specific tunnel type. The destination port value is provided in
+ * the input. If the HWRM supports only one global destination port for a tunnel
+ * type, then the HWRM shall keep track of its usage as described below. # The
+ * first caller that allocates a destination port shall always succeed and the
+ * HWRM shall save the destination port configuration for that tunnel type and
+ * increment the usage count to 1. # Subsequent callers allocating the same
+ * destination port for that tunnel type shall succeed and the HWRM shall
+ * increment the usage count for that port for each subsequent caller that
+ * succeeds. # Any subsequent caller trying to allocate a different destination
+ * port for that tunnel type shall fail until the usage count for the original
+ * destination port goes to zero. # A caller that frees a port will cause the
+ * usage count for that port to decrement.
*/
-/* Input (24 bytes) */
-struct hwrm_queue_qportcfg_input {
+/* Input (24 bytes) */
+struct hwrm_tunnel_dst_port_alloc_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -6774,29 +23845,31 @@ struct hwrm_queue_qportcfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t flags;
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_VXLAN 0x1UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_GENEVE 0x5UL
/*
- * Enumeration denoting the RX, TX type of the resource. This
- * enumeration is used for resources that are similar for both
- * TX and RX paths of the chip.
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
*/
- #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH UINT32_C(0x1)
- /* tx path */
- #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
- /* rx path */
- #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
- #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_LAST \
- QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX
- uint16_t port_id;
+ #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 0x9UL
+ uint8_t unused_0;
+ uint16_t tunnel_dst_port_val;
/*
- * Port ID of port for which the queue configuration is being
- * queried. This field is only required when sent by IPC.
+ * This field represents the value of L4 destination port used
+ * for the given tunnel type. This field is valid for specific
+ * tunnel types that use layer 4 (e.g. UDP) transports for
+ * tunneling. This field is in network byte order. A value of 0
+ * shall fail the command.
*/
- uint16_t unused_0;
+ uint32_t unused_1;
} __attribute__((packed));
-/* Output (32 bytes) */
-struct hwrm_queue_qportcfg_output {
+/* Output (16 bytes) */
+struct hwrm_tunnel_dst_port_alloc_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -6812,295 +23885,279 @@ struct hwrm_queue_qportcfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint8_t max_configurable_queues;
+ uint16_t tunnel_dst_port_id;
/*
- * The maximum number of queues that can be configured on this
- * port. Valid values range from 1 through 8.
+ * Identifier of a tunnel L4 destination port value. Only
+ * applies to tunnel types that has l4 destination port
+ * parameters.
*/
- uint8_t max_configurable_lossless_queues;
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
/*
- * The maximum number of lossless queues that can be configured
- * on this port. Valid values range from 0 through 8.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- uint8_t queue_cfg_allowed;
+} __attribute__((packed));
+
+/* hwrm_tunnel_dst_port_free */
+/*
+ * Description: This function is called by a driver to free l4 destination port
+ * for a specific tunnel type.
+ */
+/* Input (24 bytes) */
+struct hwrm_tunnel_dst_port_free_input {
+ uint16_t req_type;
/*
- * Bitmask indicating which queues can be configured by the
- * hwrm_queue_cfg command. Each bit represents a specific queue
- * where bit 0 represents queue 0 and bit 7 represents queue 7.
- * # A value of 0 indicates that the queue is not configurable
- * by the hwrm_queue_cfg command. # A value of 1 indicates that
- * the queue is configurable. # A hwrm_queue_cfg command shall
- * return error when trying to configure a queue not
- * configurable.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- uint8_t queue_cfg_info;
- /* Information about queue configuration. */
+ uint16_t cmpl_ring;
/*
- * If this flag is set to '1', then the queues are configured
- * asymmetrically on TX and RX sides. If this flag is set to
- * '0', then the queues are configured symmetrically on TX and
- * RX sides. For symmetric configuration, the queue
- * configuration including queue ids and service profiles on the
- * TX side is the same as the corresponding queue configuration
- * on the RX side.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG UINT32_C(0x1)
- uint8_t queue_pfcenable_cfg_allowed;
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * Bitmask indicating which queues can be configured by the
- * hwrm_queue_pfcenable_cfg command. Each bit represents a
- * specific priority where bit 0 represents priority 0 and bit 7
- * represents priority 7. # A value of 0 indicates that the
- * priority is not configurable by the hwrm_queue_pfcenable_cfg
- * command. # A value of 1 indicates that the priority is
- * configurable. # A hwrm_queue_pfcenable_cfg command shall
- * return error when trying to configure a priority that is not
- * configurable.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint8_t queue_pri2cos_cfg_allowed;
+ uint64_t resp_addr;
/*
- * Bitmask indicating which queues can be configured by the
- * hwrm_queue_pri2cos_cfg command. Each bit represents a
- * specific queue where bit 0 represents queue 0 and bit 7
- * represents queue 7. # A value of 0 indicates that the queue
- * is not configurable by the hwrm_queue_pri2cos_cfg command. #
- * A value of 1 indicates that the queue is configurable. # A
- * hwrm_queue_pri2cos_cfg command shall return error when trying
- * to configure a queue that is not configurable.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint8_t queue_cos2bw_cfg_allowed;
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_VXLAN 0x1UL
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_GENEVE 0x5UL
/*
- * Bitmask indicating which queues can be configured by the
- * hwrm_queue_pri2cos_cfg command. Each bit represents a
- * specific queue where bit 0 represents queue 0 and bit 7
- * represents queue 7. # A value of 0 indicates that the queue
- * is not configurable by the hwrm_queue_pri2cos_cfg command. #
- * A value of 1 indicates that the queue is configurable. # A
- * hwrm_queue_pri2cos_cfg command shall return error when trying
- * to configure a queue not configurable.
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
+ */
+ #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_VXLAN_V4 0x9UL
+ uint8_t unused_0;
+ uint16_t tunnel_dst_port_id;
+ /*
+ * Identifier of a tunnel L4 destination port value. Only
+ * applies to tunnel types that has l4 destination port
+ * parameters.
+ */
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_tunnel_dst_port_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- uint8_t queue_id0;
+} __attribute__((packed));
+
+/* hwrm_stat_ctx_alloc */
+/*
+ * Description: This command allocates and does basic preparation for a stat
+ * context.
+ */
+/* Input (32 bytes) */
+struct hwrm_stat_ctx_alloc_input {
+ uint16_t req_type;
/*
- * ID of CoS Queue 0. FF - Invalid id # This ID can be used on
- * any subsequent call to an hwrm command that takes a queue id.
- * # IDs must always be queried by this command before any use
- * by the driver or software. # Any driver or software should
- * not make any assumptions about queue IDs. # A value of 0xff
- * indicates that the queue is not available. # Available queues
- * may not be in sequential order.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- uint8_t queue_id0_service_profile;
- /* This value is applicable to CoS queues only. */
- /* Lossy (best-effort) */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSY \
- UINT32_C(0x0)
- /* Lossless */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSLESS \
- UINT32_C(0x1)
+ uint16_t cmpl_ring;
/*
- * Set to 0xFF... (All Fs) if there is no
- * service profile specified
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_UNKNOWN \
- UINT32_C(0xff)
- uint8_t queue_id1;
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * ID of CoS Queue 1. FF - Invalid id # This ID can be used on
- * any subsequent call to an hwrm command that takes a queue id.
- * # IDs must always be queried by this command before any use
- * by the driver or software. # Any driver or software should
- * not make any assumptions about queue IDs. # A value of 0xff
- * indicates that the queue is not available. # Available queues
- * may not be in sequential order.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint8_t queue_id1_service_profile;
- /* This value is applicable to CoS queues only. */
- /* Lossy (best-effort) */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSY \
- UINT32_C(0x0)
- /* Lossless */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSLESS \
- UINT32_C(0x1)
+ uint64_t resp_addr;
/*
- * Set to 0xFF... (All Fs) if there is no
- * service profile specified
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_UNKNOWN \
- UINT32_C(0xff)
- uint8_t queue_id2;
+ uint64_t stats_dma_addr;
+ /* This is the address for statistic block. */
+ uint32_t update_period_ms;
/*
- * ID of CoS Queue 2. FF - Invalid id # This ID can be used on
- * any subsequent call to an hwrm command that takes a queue id.
- * # IDs must always be queried by this command before any use
- * by the driver or software. # Any driver or software should
- * not make any assumptions about queue IDs. # A value of 0xff
- * indicates that the queue is not available. # Available queues
- * may not be in sequential order.
+ * The statistic block update period in ms. e.g. 250ms, 500ms,
+ * 750ms, 1000ms. If update_period_ms is 0, then the stats
+ * update shall be never done and the DMA address shall not be
+ * used. In this case, the stat block can only be read by
+ * hwrm_stat_ctx_query command.
*/
- uint8_t queue_id2_service_profile;
- /* This value is applicable to CoS queues only. */
- /* Lossy (best-effort) */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSY \
- UINT32_C(0x0)
- /* Lossless */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSLESS \
- UINT32_C(0x1)
+ uint8_t stat_ctx_flags;
/*
- * Set to 0xFF... (All Fs) if there is no
- * service profile specified
+ * This field is used to specify statistics context specific
+ * configuration flags.
*/
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_UNKNOWN \
- UINT32_C(0xff)
- uint8_t queue_id3;
/*
- * ID of CoS Queue 3. FF - Invalid id # This ID can be used on
- * any subsequent call to an hwrm command that takes a queue id.
- * # IDs must always be queried by this command before any use
- * by the driver or software. # Any driver or software should
- * not make any assumptions about queue IDs. # A value of 0xff
- * indicates that the queue is not available. # Available queues
- * may not be in sequential order.
+ * When this bit is set to '1', the statistics context shall be
+ * allocated for RoCE traffic only. In this case, traffic other
+ * than offloaded RoCE traffic shall not be included in this
+ * statistic context. When this bit is set to '0', the
+ * statistics context shall be used for the network traffic
+ * other than offloaded RoCE traffic.
*/
- uint8_t queue_id3_service_profile;
- /* This value is applicable to CoS queues only. */
- /* Lossy (best-effort) */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSY \
- UINT32_C(0x0)
- /* Lossless */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS \
- UINT32_C(0x1)
+ #define HWRM_STAT_CTX_ALLOC_INPUT_STAT_CTX_FLAGS_ROCE 0x1UL
+ uint8_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_stat_ctx_alloc_output {
+ uint16_t error_code;
/*
- * Set to 0xFF... (All Fs) if there is no
- * service profile specified
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_UNKNOWN \
- UINT32_C(0xff)
- uint8_t queue_id4;
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * ID of CoS Queue 4. FF - Invalid id # This ID can be used on
- * any subsequent call to an hwrm command that takes a queue id.
- * # IDs must always be queried by this command before any use
- * by the driver or software. # Any driver or software should
- * not make any assumptions about queue IDs. # A value of 0xff
- * indicates that the queue is not available. # Available queues
- * may not be in sequential order.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- uint8_t queue_id4_service_profile;
- /* This value is applicable to CoS queues only. */
- /* Lossy (best-effort) */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSY \
- UINT32_C(0x0)
- /* Lossless */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS \
- UINT32_C(0x1)
+ uint32_t stat_ctx_id;
+ /* This is the statistics context ID value. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
/*
- * Set to 0xFF... (All Fs) if there is no
- * service profile specified
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_UNKNOWN \
- UINT32_C(0xff)
- uint8_t queue_id5;
+} __attribute__((packed));
+
+/* hwrm_stat_ctx_free */
+/* Description: This command is used to free a stat context. */
+/* Input (24 bytes) */
+struct hwrm_stat_ctx_free_input {
+ uint16_t req_type;
/*
- * ID of CoS Queue 5. FF - Invalid id # This ID can be used on
- * any subsequent call to an hwrm command that takes a queue id.
- * # IDs must always be queried by this command before any use
- * by the driver or software. # Any driver or software should
- * not make any assumptions about queue IDs. # A value of 0xff
- * indicates that the queue is not available. # Available queues
- * may not be in sequential order.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- uint8_t queue_id5_service_profile;
- /* This value is applicable to CoS queues only. */
- /* Lossy (best-effort) */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSY \
- UINT32_C(0x0)
- /* Lossless */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS \
- UINT32_C(0x1)
+ uint16_t cmpl_ring;
/*
- * Set to 0xFF... (All Fs) if there is no
- * service profile specified
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_UNKNOWN \
- UINT32_C(0xff)
- uint8_t queue_id6;
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * ID of CoS Queue 6. FF - Invalid id # This ID can be used on
- * any subsequent call to an hwrm command that takes a queue id.
- * # IDs must always be queried by this command before any use
- * by the driver or software. # Any driver or software should
- * not make any assumptions about queue IDs. # A value of 0xff
- * indicates that the queue is not available. # Available queues
- * may not be in sequential order.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint8_t queue_id6_service_profile;
- /* This value is applicable to CoS queues only. */
- /* Lossy (best-effort) */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSY \
- UINT32_C(0x0)
- /* Lossless */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS \
- UINT32_C(0x1)
+ uint64_t resp_addr;
/*
- * Set to 0xFF... (All Fs) if there is no
- * service profile specified
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_UNKNOWN \
- UINT32_C(0xff)
- uint8_t queue_id7;
+ uint32_t stat_ctx_id;
+ /* ID of the statistics context that is being queried. */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_stat_ctx_free_output {
+ uint16_t error_code;
/*
- * ID of CoS Queue 7. FF - Invalid id # This ID can be used on
- * any subsequent call to an hwrm command that takes a queue id.
- * # IDs must always be queried by this command before any use
- * by the driver or software. # Any driver or software should
- * not make any assumptions about queue IDs. # A value of 0xff
- * indicates that the queue is not available. # Available queues
- * may not be in sequential order.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- uint8_t queue_id7_service_profile;
- /* This value is applicable to CoS queues only. */
- /* Lossy (best-effort) */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSY \
- UINT32_C(0x0)
- /* Lossless */
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS \
- UINT32_C(0x1)
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * Set to 0xFF... (All Fs) if there is no
- * service profile specified
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_UNKNOWN \
- UINT32_C(0xff)
+ uint32_t stat_ctx_id;
+ /* This is the statistics context ID value. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
* output is completely written to RAM. This field should be
* read as '1' to indicate that the output has been completely
* written. When writing a command completion or response to an
- * internal processor, the order of writes has to be such that
- * this field is written last.
- */
-} __attribute__((packed));
-
-/* hwrm_vnic_alloc */
-/*
- * Description: This VNIC is a resource in the RX side of the chip that is used
- * to represent a virtual host "interface". # At the time of VNIC allocation or
- * configuration, the function can specify whether it wants the requested VNIC
- * to be the default VNIC for the function or not. # If a function requests
- * allocation of a VNIC for the first time and a VNIC is successfully allocated
- * by the HWRM, then the HWRM shall make the allocated VNIC as the default VNIC
- * for that function. # The default VNIC shall be used for the default action
- * for a partition or function. # For each VNIC allocated on a function, a
- * mapping on the RX side to map the allocated VNIC to source virtual interface
- * shall be performed by the HWRM. This should be hidden to the function driver
- * requesting the VNIC allocation. This enables broadcast/multicast replication
- * with source knockout. # If multicast replication with source knockout is
- * enabled, then the internal VNIC to SVIF mapping data structures shall be
- * programmed at the time of VNIC allocation.
- */
-/* Input (24 bytes) */
-struct hwrm_vnic_alloc_input {
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_stat_ctx_query */
+/* Description: This command returns statistics of a context. */
+/* Input (24 bytes) */
+struct hwrm_stat_ctx_query_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -7127,17 +24184,13 @@ struct hwrm_vnic_alloc_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t flags;
- /*
- * When this bit is '1', this VNIC is requested to be the
- * default VNIC for this function.
- */
- #define HWRM_VNIC_ALLOC_INPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ uint32_t stat_ctx_id;
+ /* ID of the statistics context that is being queried. */
uint32_t unused_0;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_vnic_alloc_output {
+/* Output (176 bytes) */
+struct hwrm_stat_ctx_query_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -7153,11 +24206,50 @@ struct hwrm_vnic_alloc_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t vnic_id;
- /* Logical vnic ID */
- uint8_t unused_0;
+ uint64_t tx_ucast_pkts;
+ /* Number of transmitted unicast packets */
+ uint64_t tx_mcast_pkts;
+ /* Number of transmitted multicast packets */
+ uint64_t tx_bcast_pkts;
+ /* Number of transmitted broadcast packets */
+ uint64_t tx_err_pkts;
+ /* Number of transmitted packets with error */
+ uint64_t tx_drop_pkts;
+ /* Number of dropped packets on transmit path */
+ uint64_t tx_ucast_bytes;
+ /* Number of transmitted bytes for unicast traffic */
+ uint64_t tx_mcast_bytes;
+ /* Number of transmitted bytes for multicast traffic */
+ uint64_t tx_bcast_bytes;
+ /* Number of transmitted bytes for broadcast traffic */
+ uint64_t rx_ucast_pkts;
+ /* Number of received unicast packets */
+ uint64_t rx_mcast_pkts;
+ /* Number of received multicast packets */
+ uint64_t rx_bcast_pkts;
+ /* Number of received broadcast packets */
+ uint64_t rx_err_pkts;
+ /* Number of received packets with error */
+ uint64_t rx_drop_pkts;
+ /* Number of dropped packets on received path */
+ uint64_t rx_ucast_bytes;
+ /* Number of received bytes for unicast traffic */
+ uint64_t rx_mcast_bytes;
+ /* Number of received bytes for multicast traffic */
+ uint64_t rx_bcast_bytes;
+ /* Number of received bytes for broadcast traffic */
+ uint64_t rx_agg_pkts;
+ /* Number of aggregated unicast packets */
+ uint64_t rx_agg_bytes;
+ /* Number of aggregated unicast bytes */
+ uint64_t rx_agg_events;
+ /* Number of aggregation events */
+ uint64_t rx_agg_aborts;
+ /* Number of aborted aggregations */
+ uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -7169,14 +24261,10 @@ struct hwrm_vnic_alloc_output {
*/
} __attribute__((packed));
-/* hwrm_vnic_free */
-/*
- * Description: Free a VNIC resource. Idle any resources associated with the
- * VNIC as well as the VNIC. Reset and release all resources associated with the
- * VNIC.
- */
-/* Input (24 bytes) */
-struct hwrm_vnic_free_input {
+/* hwrm_stat_ctx_clr_stats */
+/* Description: This command clears statistics of a context. */
+/* Input (24 bytes) */
+struct hwrm_stat_ctx_clr_stats_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -7203,13 +24291,13 @@ struct hwrm_vnic_free_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t vnic_id;
- /* Logical vnic ID */
+ uint32_t stat_ctx_id;
+ /* ID of the statistics context that is being queried. */
uint32_t unused_0;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_vnic_free_output {
+/* Output (16 bytes) */
+struct hwrm_stat_ctx_clr_stats_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -7240,10 +24328,13 @@ struct hwrm_vnic_free_output {
*/
} __attribute__((packed));
-/* hwrm_vnic_cfg */
-/* Description: Configure the RX VNIC structure. */
-/* Input (40 bytes) */
-struct hwrm_vnic_cfg_input {
+/* hwrm_fw_reset */
+/*
+ * Description: This function is called by a driver to self reset the firmware
+ * running on the processor indicated by the embedded_proc_type.
+ */
+/* Input (24 bytes) */
+struct hwrm_fw_reset_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -7270,103 +24361,48 @@ struct hwrm_vnic_cfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t flags;
- /*
- * When this bit is '1', the VNIC is requested to be the default
- * VNIC for the function.
- */
- #define HWRM_VNIC_CFG_INPUT_FLAGS_DEFAULT UINT32_C(0x1)
- /*
- * When this bit is '1', the VNIC is being configured to strip
- * VLAN in the RX path. If set to '0', then VLAN stripping is
- * disabled on this VNIC.
- */
- #define HWRM_VNIC_CFG_INPUT_FLAGS_VLAN_STRIP_MODE UINT32_C(0x2)
- /*
- * When this bit is '1', the VNIC is being configured to buffer
- * receive packets in the hardware until the host posts new
- * receive buffers. If set to '0', then bd_stall is being
- * configured to be disabled on this VNIC.
- */
- #define HWRM_VNIC_CFG_INPUT_FLAGS_BD_STALL_MODE UINT32_C(0x4)
- /*
- * When this bit is '1', the VNIC is being configured to receive
- * both RoCE and non-RoCE traffic. If set to '0', then this VNIC
- * is not configured to be operating in dual VNIC mode.
- */
- #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_DUAL_VNIC_MODE UINT32_C(0x8)
- /*
- * When this flag is set to '1', the VNIC is requested to be
- * configured to receive only RoCE traffic. If this flag is set
- * to '0', then this flag shall be ignored by the HWRM. If
- * roce_dual_vnic_mode flag is set to '1', then the HWRM client
- * shall not set this flag to '1'.
- */
- #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_ONLY_VNIC_MODE UINT32_C(0x10)
- /*
- * When a VNIC uses one destination ring group for certain
- * application (e.g. Receive Flow Steering) where exact match is
- * used to direct packets to a VNIC with one destination ring
- * group only, there is no need to configure RSS indirection
- * table for that VNIC as only one destination ring group is
- * used. This flag is used to enable a mode where RSS is enabled
- * in the VNIC using a RSS context for computing RSS hash but
- * the RSS indirection table is not configured using
- * hwrm_vnic_rss_cfg. If this mode is enabled, then the driver
- * should not program RSS indirection table for the RSS context
- * that is used for computing RSS hash only.
- */
- #define HWRM_VNIC_CFG_INPUT_FLAGS_RSS_DFLT_CR_MODE UINT32_C(0x20)
- uint32_t enables;
- /*
- * This bit must be '1' for the dflt_ring_grp field to be
- * configured.
- */
- #define HWRM_VNIC_CFG_INPUT_ENABLES_DFLT_RING_GRP UINT32_C(0x1)
- /* This bit must be '1' for the rss_rule field to be configured. */
- #define HWRM_VNIC_CFG_INPUT_ENABLES_RSS_RULE UINT32_C(0x2)
- /* This bit must be '1' for the cos_rule field to be configured. */
- #define HWRM_VNIC_CFG_INPUT_ENABLES_COS_RULE UINT32_C(0x4)
- /* This bit must be '1' for the lb_rule field to be configured. */
- #define HWRM_VNIC_CFG_INPUT_ENABLES_LB_RULE UINT32_C(0x8)
- /* This bit must be '1' for the mru field to be configured. */
- #define HWRM_VNIC_CFG_INPUT_ENABLES_MRU UINT32_C(0x10)
- uint16_t vnic_id;
- /* Logical vnic ID */
- uint16_t dflt_ring_grp;
- /*
- * Default Completion ring for the VNIC. This ring will be
- * chosen if packet does not match any RSS rules and if there is
- * no COS rule.
- */
- uint16_t rss_rule;
- /*
- * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if
- * there is no RSS rule.
- */
- uint16_t cos_rule;
- /*
- * RSS ID for COS rule/table structure. 0xFF... (All Fs) if
- * there is no COS rule.
- */
- uint16_t lb_rule;
- /*
- * RSS ID for load balancing rule/table structure. 0xFF... (All
- * Fs) if there is no LB rule.
- */
- uint16_t mru;
- /*
- * The maximum receive unit of the vnic. Each vnic is associated
- * with a function. The vnic mru value overwrites the mru
- * setting of the associated function. The HWRM shall make sure
- * that vnic mru does not exceed the mru of the port the
- * function is associated with.
+ uint8_t embedded_proc_type;
+ /* Type of embedded processor. */
+ /* Boot Processor */
+ #define HWRM_FW_RESET_INPUT_EMBEDDED_PROC_TYPE_BOOT 0x0UL
+ /* Management Processor */
+ #define HWRM_FW_RESET_INPUT_EMBEDDED_PROC_TYPE_MGMT 0x1UL
+ /* Network control processor */
+ #define HWRM_FW_RESET_INPUT_EMBEDDED_PROC_TYPE_NETCTRL 0x2UL
+ /* RoCE control processor */
+ #define HWRM_FW_RESET_INPUT_EMBEDDED_PROC_TYPE_ROCE 0x3UL
+ /*
+ * Host (in multi-host environment): This is
+ * only valid if requester is IPC
+ */
+ #define HWRM_FW_RESET_INPUT_EMBEDDED_PROC_TYPE_HOST 0x4UL
+ /*
+ * AP processor complex (in multi-host
+ * environment). Use host_idx to control which
+ * core is reset
+ */
+ #define HWRM_FW_RESET_INPUT_EMBEDDED_PROC_TYPE_AP 0x5UL
+ /* Reset all blocks of the chip (including all processors) */
+ #define HWRM_FW_RESET_INPUT_EMBEDDED_PROC_TYPE_CHIP 0x6UL
+ uint8_t selfrst_status;
+ /* Type of self reset. */
+ /* No Self Reset */
+ #define HWRM_FW_RESET_INPUT_SELFRST_STATUS_SELFRSTNONE 0x0UL
+ /* Self Reset as soon as possible to do so safely */
+ #define HWRM_FW_RESET_INPUT_SELFRST_STATUS_SELFRSTASAP 0x1UL
+ /* Self Reset on PCIe Reset */
+ #define HWRM_FW_RESET_INPUT_SELFRST_STATUS_SELFRSTPCIERST 0x2UL
+ uint8_t host_idx;
+ /*
+ * Indicate which host is being reset. 0 means first host. Only
+ * valid when embedded_proc_type is host in multihost
+ * environment
*/
- uint32_t unused_0;
+ uint8_t unused_0[5];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_vnic_cfg_output {
+/* Output (16 bytes) */
+struct hwrm_fw_reset_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -7382,10 +24418,19 @@ struct hwrm_vnic_cfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t unused_0;
- uint8_t unused_1;
+ uint8_t selfrst_status;
+ /* Type of self reset. */
+ /* No Self Reset */
+ #define HWRM_FW_RESET_OUTPUT_SELFRST_STATUS_SELFRSTNONE 0x0UL
+ /* Self Reset as soon as possible to do so safely */
+ #define HWRM_FW_RESET_OUTPUT_SELFRST_STATUS_SELFRSTASAP 0x1UL
+ /* Self Reset on PCIe Reset */
+ #define HWRM_FW_RESET_OUTPUT_SELFRST_STATUS_SELFRSTPCIERST 0x2UL
+ uint8_t unused_0;
+ uint16_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
+ uint8_t unused_4;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -7397,14 +24442,13 @@ struct hwrm_vnic_cfg_output {
*/
} __attribute__((packed));
-/* hwrm_vnic_qcfg */
+/* hwrm_fw_qstatus */
/*
- * Description: Query the RX VNIC structure. This function can be used by a PF
- * driver to query its own VNIC resource or VNIC resource of its child VF. This
- * function can also be used by a VF driver to query its own VNIC resource.
+ * Description: This function is called by a driver to query the status of the
+ * firmware running on the processor indicated by the embedded_proc_type.
*/
-/* Input (32 bytes) */
-struct hwrm_vnic_qcfg_input {
+/* Input (24 bytes) */
+struct hwrm_fw_qstatus_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -7431,18 +24475,34 @@ struct hwrm_vnic_qcfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t enables;
- /* This bit must be '1' for the vf_id_valid field to be configured. */
- #define HWRM_VNIC_QCFG_INPUT_ENABLES_VF_ID_VALID UINT32_C(0x1)
- uint32_t vnic_id;
- /* Logical vnic ID */
- uint16_t vf_id;
- /* ID of Virtual Function whose VNIC resource is being queried. */
- uint16_t unused_0[3];
+ uint8_t embedded_proc_type;
+ /* Type of embedded processor. */
+ /* Boot Processor */
+ #define HWRM_FW_QSTATUS_INPUT_EMBEDDED_PROC_TYPE_BOOT 0x0UL
+ /* Management Processor */
+ #define HWRM_FW_QSTATUS_INPUT_EMBEDDED_PROC_TYPE_MGMT 0x1UL
+ /* Network control processor */
+ #define HWRM_FW_QSTATUS_INPUT_EMBEDDED_PROC_TYPE_NETCTRL 0x2UL
+ /* RoCE control processor */
+ #define HWRM_FW_QSTATUS_INPUT_EMBEDDED_PROC_TYPE_ROCE 0x3UL
+ /*
+ * Host (in multi-host environment): This is
+ * only valid if requester is IPC
+ */
+ #define HWRM_FW_QSTATUS_INPUT_EMBEDDED_PROC_TYPE_HOST 0x4UL
+ /*
+ * AP processor complex (in multi-host
+ * environment). Use host_idx to control which
+ * core is reset
+ */
+ #define HWRM_FW_QSTATUS_INPUT_EMBEDDED_PROC_TYPE_AP 0x5UL
+ /* Reset all blocks of the chip (including all processors) */
+ #define HWRM_FW_QSTATUS_INPUT_EMBEDDED_PROC_TYPE_CHIP 0x6UL
+ uint8_t unused_0[7];
} __attribute__((packed));
-/* Output (32 bytes) */
-struct hwrm_vnic_qcfg_output {
+/* Output (16 bytes) */
+struct hwrm_fw_qstatus_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -7458,78 +24518,115 @@ struct hwrm_vnic_qcfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint16_t dflt_ring_grp;
- /* Default Completion ring for the VNIC. */
- uint16_t rss_rule;
- /*
- * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if
- * there is no RSS rule.
- */
- uint16_t cos_rule;
- /*
- * RSS ID for COS rule/table structure. 0xFF... (All Fs) if
- * there is no COS rule.
- */
- uint16_t lb_rule;
+ uint8_t selfrst_status;
+ /* Type of self reset. */
+ /* No Self Reset */
+ #define HWRM_FW_QSTATUS_OUTPUT_SELFRST_STATUS_SELFRSTNONE 0x0UL
+ /* Self Reset as soon as possible to do so safely */
+ #define HWRM_FW_QSTATUS_OUTPUT_SELFRST_STATUS_SELFRSTASAP 0x1UL
+ /* Self Reset on PCIe Reset */
+ #define HWRM_FW_QSTATUS_OUTPUT_SELFRST_STATUS_SELFRSTPCIERST 0x2UL
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
/*
- * RSS ID for load balancing rule/table structure. 0xFF... (All
- * Fs) if there is no LB rule.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- uint16_t mru;
- /* The maximum receive unit of the vnic. */
- uint8_t unused_0;
- uint8_t unused_1;
- uint32_t flags;
+} __attribute__((packed));
+
+/* hwrm_fw_set_time */
+/*
+ * Description: Inform the HWRM firmware of the current date/time. Ideally, the
+ * date/time will be current time in GMT/UTC and the zone value will be 0
+ * (indicating UTC). If the time zone is not known, the zone value shall be
+ * 0xffff. Other values for zone are discouraged, but if specified, they
+ * indicate the number of minutes east of UTC, while zones west of UTC are
+ * represented with a 2's complement negative value (e.g. PST would be -480
+ * while PDT would be -420).
+ */
+/* Input (32 bytes) */
+struct hwrm_fw_set_time_input {
+ uint16_t req_type;
/*
- * When this bit is '1', the VNIC is the default VNIC for the
- * function.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ uint16_t cmpl_ring;
/*
- * When this bit is '1', the VNIC is configured to strip VLAN in
- * the RX path. If set to '0', then VLAN stripping is disabled
- * on this VNIC.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_VLAN_STRIP_MODE UINT32_C(0x2)
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * When this bit is '1', the VNIC is configured to buffer
- * receive packets in the hardware until the host posts new
- * receive buffers. If set to '0', then bd_stall is disabled on
- * this VNIC.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_BD_STALL_MODE UINT32_C(0x4)
+ uint64_t resp_addr;
/*
- * When this bit is '1', the VNIC is configured to receive both
- * RoCE and non-RoCE traffic. If set to '0', then this VNIC is
- * not configured to operate in dual VNIC mode.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_DUAL_VNIC_MODE UINT32_C(0x8)
+ uint16_t year;
+ /* Current year */
+ /* Date/time is not known */
+ #define HWRM_FW_SET_TIME_INPUT_YEAR_UNKNOWN 0x0UL
+ uint8_t month;
+ /* Current month of year (1-12) */
+ uint8_t day;
+ /* Current day of month (1-31) */
+ uint8_t hour;
+ /* Current hour (0-23) */
+ uint8_t minute;
+ /* Current minute (0-59) */
+ uint8_t second;
+ /* Current second (0-59) */
+ uint8_t unused_0;
+ uint16_t millisecond;
+ /* Current millisecond (0-999) */
+ uint16_t zone;
+ /* Minutes east of UTC, 0xffff if TZ is not known */
+ /* Time zone is Coordinated Universal Time (UTC) */
+ #define HWRM_FW_SET_TIME_INPUT_ZONE_UTC 0x0UL
+ /* Time zone is not known */
+ #define HWRM_FW_SET_TIME_INPUT_ZONE_UNKNOWN 0xffffUL
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_fw_set_time_output {
+ uint16_t error_code;
/*
- * When this flag is set to '1', the VNIC is configured to
- * receive only RoCE traffic. When this flag is set to '0', the
- * VNIC is not configured to receive only RoCE traffic. If
- * roce_dual_vnic_mode flag and this flag both are set to '1',
- * then it is an invalid configuration of the VNIC. The HWRM
- * should not allow that type of mis-configuration by HWRM
- * clients.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_ONLY_VNIC_MODE UINT32_C(0x10)
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * When a VNIC uses one destination ring group for certain
- * application (e.g. Receive Flow Steering) where exact match is
- * used to direct packets to a VNIC with one destination ring
- * group only, there is no need to configure RSS indirection
- * table for that VNIC as only one destination ring group is
- * used. When this bit is set to '1', then the VNIC is enabled
- * in a mode where RSS is enabled in the VNIC using a RSS
- * context for computing RSS hash but the RSS indirection table
- * is not configured.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_RSS_DFLT_CR_MODE UINT32_C(0x20)
- uint32_t unused_2;
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
uint8_t unused_3;
- uint8_t unused_4;
- uint8_t unused_5;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -7541,10 +24638,10 @@ struct hwrm_vnic_qcfg_output {
*/
} __attribute__((packed));
-/* hwrm_vnic_rss_cfg */
-/* Description: This function is used to enable RSS configuration. */
-/* Input (48 bytes) */
-struct hwrm_vnic_rss_cfg_input {
+/* hwrm_fw_get_time */
+/* Description: Query the HWRM firmware's notion of the current date/time. */
+/* Input (16 bytes) */
+struct hwrm_fw_get_time_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -7571,53 +24668,10 @@ struct hwrm_vnic_rss_cfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t hash_type;
- /*
- * When this bit is '1', the RSS hash shall be computed over
- * source and destination IPv4 addresses of IPv4 packets.
- */
- #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV4 UINT32_C(0x1)
- /*
- * When this bit is '1', the RSS hash shall be computed over
- * source/destination IPv4 addresses and source/destination
- * ports of TCP/IPv4 packets.
- */
- #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV4 UINT32_C(0x2)
- /*
- * When this bit is '1', the RSS hash shall be computed over
- * source/destination IPv4 addresses and source/destination
- * ports of UDP/IPv4 packets.
- */
- #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV4 UINT32_C(0x4)
- /*
- * When this bit is '1', the RSS hash shall be computed over
- * source and destination IPv4 addresses of IPv6 packets.
- */
- #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV6 UINT32_C(0x8)
- /*
- * When this bit is '1', the RSS hash shall be computed over
- * source/destination IPv6 addresses and source/destination
- * ports of TCP/IPv6 packets.
- */
- #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV6 UINT32_C(0x10)
- /*
- * When this bit is '1', the RSS hash shall be computed over
- * source/destination IPv6 addresses and source/destination
- * ports of UDP/IPv6 packets.
- */
- #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV6 UINT32_C(0x20)
- uint32_t unused_0;
- uint64_t ring_grp_tbl_addr;
- /* This is the address for rss ring group table */
- uint64_t hash_key_tbl_addr;
- /* This is the address for rss hash key table */
- uint16_t rss_ctx_idx;
- /* Index to the rss indirection table. */
- uint16_t unused_1[3];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_vnic_rss_cfg_output {
+/* Output (24 bytes) */
+struct hwrm_fw_get_time_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -7633,7 +24687,29 @@ struct hwrm_vnic_rss_cfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t unused_0;
+ uint16_t year;
+ /* Current year */
+ /* Date/time is not known */
+ #define HWRM_FW_GET_TIME_OUTPUT_YEAR_UNKNOWN 0x0UL
+ uint8_t month;
+ /* Current month of year (1-12) */
+ uint8_t day;
+ /* Current day of month (1-31) */
+ uint8_t hour;
+ /* Current hour (0-23) */
+ uint8_t minute;
+ /* Current minute (0-59) */
+ uint8_t second;
+ /* Current second (0-59) */
+ uint8_t unused_0;
+ uint16_t millisecond;
+ /* Current millisecond (0-999) */
+ uint16_t zone;
+ /* Minutes east of UTC, 0xffff if TZ is not known */
+ /* Time zone is Coordinated Universal Time (UTC) */
+ #define HWRM_FW_GET_TIME_OUTPUT_ZONE_UTC 0x0UL
+ /* Time zone is not known */
+ #define HWRM_FW_GET_TIME_OUTPUT_ZONE_UNKNOWN 0xffffUL
uint8_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
@@ -7648,137 +24724,65 @@ struct hwrm_vnic_rss_cfg_output {
*/
} __attribute__((packed));
-/* hwrm_vnic_plcmodes_cfg */
+/* hwrm_fw_set_structured_data */
/*
- * Description: This function can be used to set placement mode configuration of
- * the VNIC.
+ * Description: There can be a variable number of Structure Data Headers (SDH)
+ * between offset 0x0 and the 'valid' field to handle customizable return
+ * values. Each Structure Data Header will include one defined structure. The
+ * number of returned structures can be 0, in which case the 'valid' field
+ * starts at offset 0x8. The 'valid' field offset is adjusted based on the
+ * Structure Data Header length and the length of the structured data it
+ * contains.
*/
-/* Input (40 bytes) */
-
-struct hwrm_vnic_plcmodes_cfg_input {
+/* Input (32 bytes) */
+struct hwrm_fw_set_structured_data_input {
uint16_t req_type;
/*
- * This value indicates what type of request this is. The format for the
- * rest of the command is determined by this field.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
uint16_t cmpl_ring;
/*
- * This value indicates the what completion ring the request will be
- * optionally completed on. If the value is -1, then no CR completion
- * will be generated. Any other value must be a valid CR ring_id value
- * for this function.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
uint16_t seq_id;
/* This value indicates the command sequence number. */
uint16_t target_id;
/*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
- * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
uint64_t resp_addr;
/*
- * This is the host address where the response will be written when the
- * request is complete. This area must be 16B aligned and must be
- * cleared to zero before the request is made.
- */
- uint32_t flags;
- /*
- * When this bit is '1', the VNIC shall be configured to use regular
- * placement algorithm. By default, the regular placement algorithm
- * shall be enabled on the VNIC.
- */
- #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_REGULAR_PLACEMENT \
- UINT32_C(0x1)
- /*
- * When this bit is '1', the VNIC shall be configured use the jumbo
- * placement algorithm.
- */
- #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_JUMBO_PLACEMENT \
- UINT32_C(0x2)
- /*
- * When this bit is '1', the VNIC shall be configured to enable Header-
- * Data split for IPv4 packets according to the following rules: # If
- * the packet is identified as TCP/IPv4, then the packet is split at the
- * beginning of the TCP payload. # If the packet is identified as
- * UDP/IPv4, then the packet is split at the beginning of UDP payload. #
- * If the packet is identified as non-TCP and non-UDP IPv4 packet, then
- * the packet is split at the beginning of the upper layer protocol
- * header carried in the IPv4 packet.
- */
- #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV4 UINT32_C(0x4)
- /*
- * When this bit is '1', the VNIC shall be configured to enable Header-
- * Data split for IPv6 packets according to the following rules: # If
- * the packet is identified as TCP/IPv6, then the packet is split at the
- * beginning of the TCP payload. # If the packet is identified as
- * UDP/IPv6, then the packet is split at the beginning of UDP payload. #
- * If the packet is identified as non-TCP and non-UDP IPv6 packet, then
- * the packet is split at the beginning of the upper layer protocol
- * header carried in the IPv6 packet.
- */
- #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV6 UINT32_C(0x8)
- /*
- * When this bit is '1', the VNIC shall be configured to enable Header-
- * Data split for FCoE packets at the beginning of FC payload.
- */
- #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_FCOE UINT32_C(0x10)
- /*
- * When this bit is '1', the VNIC shall be configured to enable Header-
- * Data split for RoCE packets at the beginning of RoCE payload (after
- * BTH/GRH headers).
- */
- #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_ROCE UINT32_C(0x20)
- uint32_t enables;
- /*
- * This bit must be '1' for the jumbo_thresh_valid field to be
- * configured.
- */
- #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_JUMBO_THRESH_VALID \
- UINT32_C(0x1)
- /*
- * This bit must be '1' for the hds_offset_valid field to be configured.
- */
- #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_OFFSET_VALID \
- UINT32_C(0x2)
- /*
- * This bit must be '1' for the hds_threshold_valid field to be
- * configured.
- */
- #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_THRESHOLD_VALID \
- UINT32_C(0x4)
- uint32_t vnic_id;
- /* Logical vnic ID */
- uint16_t jumbo_thresh;
- /*
- * When jumbo placement algorithm is enabled, this value is used to
- * determine the threshold for jumbo placement. Packets with length
- * larger than this value will be placed according to the jumbo
- * placement algorithm.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint16_t hds_offset;
+ uint64_t src_data_addr;
/*
- * This value is used to determine the offset into packet buffer where
- * the split data (payload) will be placed according to one of of HDS
- * placement algorithm. The lengths of packet buffers provided for split
- * data shall be larger than this value.
+ * This is the host address where structured data will be copied
+ * from
*/
- uint16_t hds_threshold;
+ uint16_t data_len;
+ /* size of data in bytes */
+ uint8_t hdr_cnt;
/*
- * When one of the HDS placement algorithm is enabled, this value is
- * used to determine the threshold for HDS placement. Packets with
- * length larger than this value will be placed according to the HDS
- * placement algorithm. This value shall be in multiple of 4 bytes.
+ * a count of the number of Structured Data Headers in the data
+ * pointed by src_data_addr.
*/
- uint16_t unused_0[3];
+ uint8_t unused_0[5];
} __attribute__((packed));
/* Output (16 bytes) */
-
-struct hwrm_vnic_plcmodes_cfg_output {
+struct hwrm_fw_set_structured_data_output {
uint16_t error_code;
/*
- * Pass/Fail or error type Note: receiver to verify the in parameters,
- * and fail the call with an error when appropriate
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
uint16_t req_type;
/* This field returns the type of original request. */
@@ -7786,9 +24790,9 @@ struct hwrm_vnic_plcmodes_cfg_output {
/* This field provides original sequence number of the command. */
uint16_t resp_len;
/*
- * This field is the length of the response in bytes. The last byte of
- * the response is a valid flag that will read as '1' when the command
- * has been completely written to memory.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
uint32_t unused_0;
uint8_t unused_1;
@@ -7796,59 +24800,110 @@ struct hwrm_vnic_plcmodes_cfg_output {
uint8_t unused_3;
uint8_t valid;
/*
- * This field is used in Output records to indicate that the output is
- * completely written to RAM. This field should be read as '1' to
- * indicate that the output has been completely written. When writing a
- * command completion or response to an internal processor, the order of
- * writes has to be such that this field is written last.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
} __attribute__((packed));
-/* hwrm_vnic_plcmodes_qcfg */
-/*
- * Description: This function can be used to query placement mode configuration
- * of the VNIC.
- */
-/* Input (24 bytes) */
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_fw_set_structured_data_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_FW_SET_STRUCTURED_DATA_CMD_ERR_CODE_UNKNOWN 0x0UL
+ /* count_of_headers is incorrect */
+ #define HWRM_FW_SET_STRUCTURED_DATA_CMD_ERR_CODE_BAD_HDR_CNT 0x1UL
+ /* data improperly formatted */
+ #define HWRM_FW_SET_STRUCTURED_DATA_CMD_ERR_CODE_BAD_FMT 0x2UL
+ /* unknown structure ID(s) */
+ #define HWRM_FW_SET_STRUCTURED_DATA_CMD_ERR_CODE_BAD_ID 0x3UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
-struct hwrm_vnic_plcmodes_qcfg_input {
+/* hwrm_fw_get_structured_data */
+/* Input (32 bytes) */
+struct hwrm_fw_get_structured_data_input {
uint16_t req_type;
/*
- * This value indicates what type of request this is. The format for the
- * rest of the command is determined by this field.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
uint16_t cmpl_ring;
/*
- * This value indicates the what completion ring the request will be
- * optionally completed on. If the value is -1, then no CR completion
- * will be generated. Any other value must be a valid CR ring_id value
- * for this function.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
uint16_t seq_id;
/* This value indicates the command sequence number. */
uint16_t target_id;
/*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
- * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
uint64_t resp_addr;
/*
- * This is the host address where the response will be written when the
- * request is complete. This area must be 16B aligned and must be
- * cleared to zero before the request is made.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint32_t vnic_id;
- /* Logical vnic ID */
- uint32_t unused_0;
+ uint64_t dest_data_addr;
+ /* This is the host address where structured data will be copied to */
+ uint16_t data_len;
+ /* size of data in bytes */
+ uint16_t structure_id;
+ /*
+ * Structure_id is the id of the structure data requesting and
+ * count is a requested number of instances of this data
+ * requested. The actual number will be returned in
+ * count_of_headers
+ */
+ uint16_t subtype;
+ /*
+ * Subtype is an optional field used to specify additional
+ * information of the data being retrieved. For example, if data
+ * can be categorized as "live" vs "saved" then this field can
+ * be used to provide an indication of "saved" vs "live" data.
+ * Not all structured data supports subtypes and if they are
+ * supported then the structured data will specify the valid
+ * values. If structured data is requested that supports
+ * subtypes but no subtype is given then it is implementation
+ * specific what will be returned. Some structure data can
+ * support a subtype of "All" which would cause a list of
+ * structures to be returned for all supported subtypes. "All"
+ * is only used on the hwrm_get_structured_data command.
+ */
+ #define HWRM_FW_GET_STRUCTURED_DATA_INPUT_SUBTYPE_ALL 0xffffUL
+ #define HWRM_FW_GET_STRUCTURED_DATA_INPUT_SUBTYPE_NEAR_BRIDGE_ADMIN \
+ 0x100UL
+ #define HWRM_FW_GET_STRUCTURED_DATA_INPUT_SUBTYPE_NEAR_BRIDGE_PEER 0x101UL
+ #define HWRM_FW_GET_STRUCTURED_DATA_INPUT_SUBTYPE_NEAR_BRIDGE_OPERATIONAL \
+ 0x102UL
+ #define HWRM_FW_GET_STRUCTURED_DATA_INPUT_SUBTYPE_NON_TPMR_ADMIN 0x200UL
+ #define HWRM_FW_GET_STRUCTURED_DATA_INPUT_SUBTYPE_NON_TPMR_PEER 0x201UL
+ #define HWRM_FW_GET_STRUCTURED_DATA_INPUT_SUBTYPE_NON_TPMR_OPERATIONAL \
+ 0x202UL
+ #define HWRM_FW_GET_STRUCTURED_DATA_INPUT_SUBTYPE_HOST_OPERATIONAL 0x300UL
+ uint8_t count;
+ /* Number of elements. This allows support of arrayed data */
+ uint8_t unused_0;
} __attribute__((packed));
-/* Output (24 bytes) */
-
-struct hwrm_vnic_plcmodes_qcfg_output {
+/* Output (16 bytes) */
+struct hwrm_fw_get_structured_data_output {
uint16_t error_code;
/*
- * Pass/Fail or error type Note: receiver to verify the in parameters,
- * and fail the call with an error when appropriate
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
uint16_t req_type;
/* This field returns the type of original request. */
@@ -7856,88 +24911,52 @@ struct hwrm_vnic_plcmodes_qcfg_output {
/* This field provides original sequence number of the command. */
uint16_t resp_len;
/*
- * This field is the length of the response in bytes. The last byte of
- * the response is a valid flag that will read as '1' when the command
- * has been completely written to memory.
- */
- uint32_t flags;
- /*
- * When this bit is '1', the VNIC is configured to use regular placement
- * algorithm.
- */
- #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_REGULAR_PLACEMENT \
- UINT32_C(0x1)
- /*
- * When this bit is '1', the VNIC is configured to use the jumbo
- * placement algorithm.
- */
- #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_JUMBO_PLACEMENT \
- UINT32_C(0x2)
- /*
- * When this bit is '1', the VNIC is configured to enable Header-Data
- * split for IPv4 packets.
- */
- #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV4 UINT32_C(0x4)
- /*
- * When this bit is '1', the VNIC is configured to enable Header-Data
- * split for IPv6 packets.
- */
- #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV6 UINT32_C(0x8)
- /*
- * When this bit is '1', the VNIC is configured to enable Header-Data
- * split for FCoE packets.
- */
- #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_FCOE UINT32_C(0x10)
- /*
- * When this bit is '1', the VNIC is configured to enable Header-Data
- * split for RoCE packets.
- */
- #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_ROCE UINT32_C(0x20)
- /*
- * When this bit is '1', the VNIC is configured to be the default VNIC
- * of the requesting function.
- */
- #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_DFLT_VNIC UINT32_C(0x40)
- uint16_t jumbo_thresh;
- /*
- * When jumbo placement algorithm is enabled, this value is used to
- * determine the threshold for jumbo placement. Packets with length
- * larger than this value will be placed according to the jumbo
- * placement algorithm.
- */
- uint16_t hds_offset;
- /*
- * This value is used to determine the offset into packet buffer where
- * the split data (payload) will be placed according to one of of HDS
- * placement algorithm. The lengths of packet buffers provided for split
- * data shall be larger than this value.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- uint16_t hds_threshold;
+ uint8_t hdr_cnt;
/*
- * When one of the HDS placement algorithm is enabled, this value is
- * used to determine the threshold for HDS placement. Packets with
- * length larger than this value will be placed according to the HDS
- * placement algorithm. This value shall be in multiple of 4 bytes.
+ * a count of the number of Structured Data Headers in the data
+ * pointed by dest_data_addr.
*/
uint8_t unused_0;
- uint8_t unused_1;
+ uint16_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
uint8_t unused_4;
uint8_t valid;
/*
- * This field is used in Output records to indicate that the output is
- * completely written to RAM. This field should be read as '1' to
- * indicate that the output has been completely written. When writing a
- * command completion or response to an internal processor, the order of
- * writes has to be such that this field is written last.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
} __attribute__((packed));
-/* hwrm_vnic_rss_cos_lb_ctx_alloc */
-/* Description: This function is used to allocate COS/Load Balance context. */
-/* Input (16 bytes) */
-struct hwrm_vnic_rss_cos_lb_ctx_alloc_input {
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_fw_get_structured_data_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_FW_GET_STRUCTURED_DATA_CMD_ERR_CODE_UNKNOWN 0x0UL
+ /* unknown structure ID(s) */
+ #define HWRM_FW_GET_STRUCTURED_DATA_CMD_ERR_CODE_BAD_ID 0x3UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* hwrm_fw_ipc_msg */
+/*
+ * Description: This command allows BONO to request CFW to make CFA table
+ * changes needed to support LAG.
+ */
+/* Input (40 bytes) */
+struct hwrm_fw_ipc_msg_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -7964,10 +24983,45 @@ struct hwrm_vnic_rss_cos_lb_ctx_alloc_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
+ uint32_t enables;
+ /* This bit must be '1' for the command_id field to be configured. */
+ #define HWRM_FW_IPC_MSG_INPUT_ENABLES_COMMAND_ID 0x1UL
+ /*
+ * This bit must be '1' for the src_processor field to be
+ * configured.
+ */
+ #define HWRM_FW_IPC_MSG_INPUT_ENABLES_SRC_PROCESSOR 0x2UL
+ /* This bit must be '1' for the data_offset field to be configured. */
+ #define HWRM_FW_IPC_MSG_INPUT_ENABLES_DATA_OFFSET 0x4UL
+ /* This bit must be '1' for the length field to be configured. */
+ #define HWRM_FW_IPC_MSG_INPUT_ENABLES_LENGTH 0x8UL
+ uint16_t command_id;
+ /* Command ID */
+ /* RoCE LAG message */
+ #define HWRM_FW_IPC_MSG_INPUT_COMMAND_ID_ROCE_LAG 0x1UL
+ uint8_t src_processor;
+ /* Source processor for this command. */
+ /* Chimp processosr */
+ #define HWRM_FW_IPC_MSG_INPUT_SRC_PROCESSOR_CFW 0x1UL
+ /* BONO processor */
+ #define HWRM_FW_IPC_MSG_INPUT_SRC_PROCESSOR_BONO 0x2UL
+ /* APE processosr */
+ #define HWRM_FW_IPC_MSG_INPUT_SRC_PROCESSOR_APE 0x3UL
+ /* KONG processor */
+ #define HWRM_FW_IPC_MSG_INPUT_SRC_PROCESSOR_KONG 0x4UL
+ uint8_t unused_0;
+ uint32_t data_offset;
+ /* Offset of the data in the source processor memory. */
+ uint16_t length;
+ /* Length of the data in source processor. */
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint64_t opaque;
+ /* This is for storing FW opaque data. */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_vnic_rss_cos_lb_ctx_alloc_output {
+/* Output (16 bytes) */
+struct hwrm_fw_ipc_msg_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -7983,13 +25037,10 @@ struct hwrm_vnic_rss_cos_lb_ctx_alloc_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint16_t rss_cos_lb_ctx_id;
- /* rss_cos_lb_ctx_id is 16 b */
- uint8_t unused_0;
+ uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
- uint8_t unused_4;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -8001,10 +25052,9 @@ struct hwrm_vnic_rss_cos_lb_ctx_alloc_output {
*/
} __attribute__((packed));
-/* hwrm_vnic_rss_cos_lb_ctx_free */
-/* Description: This function can be used to free COS/Load Balance context. */
-/* Input (24 bytes) */
-struct hwrm_vnic_rss_cos_lb_ctx_free_input {
+/* hwrm_fw_ipc_mailbox */
+/* Input (32 bytes) */
+struct hwrm_fw_ipc_mailbox_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -8031,13 +25081,22 @@ struct hwrm_vnic_rss_cos_lb_ctx_free_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t rss_cos_lb_ctx_id;
- /* rss_cos_lb_ctx_id is 16 b */
- uint16_t unused_0[3];
+ uint8_t flags;
+ uint8_t unused_0;
+ /* unused is 8 b */
+ uint8_t event_id;
+ /* asynchronous event to hosts. */
+ uint8_t port_id;
+ /* PORT ID */
+ uint32_t event_data1;
+ /* event data1 of asynchronous event */
+ uint32_t event_data2;
+ /* event data2 of asynchronous event */
+ uint32_t unused_1;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_vnic_rss_cos_lb_ctx_free_output {
+/* Output (16 bytes) */
+struct hwrm_fw_ipc_mailbox_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -8068,10 +25127,32 @@ struct hwrm_vnic_rss_cos_lb_ctx_free_output {
*/
} __attribute__((packed));
-/* hwrm_vnic_tpa_cfg */
-/* Description: This function is used to enable/configure TPA on the VNIC. */
-/* Input (40 bytes) */
-struct hwrm_vnic_tpa_cfg_input {
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_fw_ipc_mailbox_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_FW_IPC_MAILBOX_CMD_ERR_CODE_UNKNOWN 0x0UL
+ /* invalid event */
+ #define HWRM_FW_IPC_MAILBOX_CMD_ERR_CODE_BAD_ID 0x3UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* hwrm_exec_fwd_resp */
+/*
+ * Description: This command is used to send an encapsulated request to the
+ * HWRM. This command instructs the HWRM to execute the request and forward the
+ * response of the encapsulated request to the location specified in the
+ * original request that is encapsulated. The target id of this command shall be
+ * set to 0xFFFF (HWRM). The response location in this command shall be used to
+ * acknowledge the receipt of the encapsulated request and forwarding of the
+ * response.
+ */
+/* Input (128 bytes) */
+struct hwrm_exec_fwd_resp_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -8098,122 +25179,24 @@ struct hwrm_vnic_tpa_cfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t flags;
- /*
- * When this bit is '1', the VNIC shall be configured to perform
- * transparent packet aggregation (TPA) of non-tunneled TCP
- * packets.
- */
- #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_TPA UINT32_C(0x1)
- /*
- * When this bit is '1', the VNIC shall be configured to perform
- * transparent packet aggregation (TPA) of tunneled TCP packets.
- */
- #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_ENCAP_TPA UINT32_C(0x2)
- /*
- * When this bit is '1', the VNIC shall be configured to perform
- * transparent packet aggregation (TPA) according to Windows
- * Receive Segment Coalescing (RSC) rules.
- */
- #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_RSC_WND_UPDATE UINT32_C(0x4)
- /*
- * When this bit is '1', the VNIC shall be configured to perform
- * transparent packet aggregation (TPA) according to Linux
- * Generic Receive Offload (GRO) rules.
- */
- #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO UINT32_C(0x8)
- /*
- * When this bit is '1', the VNIC shall be configured to perform
- * transparent packet aggregation (TPA) for TCP packets with IP
- * ECN set to non-zero.
- */
- #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_WITH_ECN UINT32_C(0x10)
- /*
- * When this bit is '1', the VNIC shall be configured to perform
- * transparent packet aggregation (TPA) for GRE tunneled TCP
- * packets only if all packets have the same GRE sequence.
- */
- #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_WITH_SAME_GRE_SEQ \
- UINT32_C(0x20)
- /*
- * When this bit is '1' and the GRO mode is enabled, the VNIC
- * shall be configured to perform transparent packet aggregation
- * (TPA) for TCP/IPv4 packets with consecutively increasing
- * IPIDs. In other words, the last packet that is being
- * aggregated to an already existing aggregation context shall
- * have IPID 1 more than the IPID of the last packet that was
- * aggregated in that aggregation context.
- */
- #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO_IPID_CHECK UINT32_C(0x40)
- /*
- * When this bit is '1' and the GRO mode is enabled, the VNIC
- * shall be configured to perform transparent packet aggregation
- * (TPA) for TCP packets with the same TTL (IPv4) or Hop limit
- * (IPv6) value.
- */
- #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO_TTL_CHECK UINT32_C(0x80)
- uint32_t enables;
- /* This bit must be '1' for the max_agg_segs field to be configured. */
- #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGG_SEGS UINT32_C(0x1)
- /* This bit must be '1' for the max_aggs field to be configured. */
- #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGGS UINT32_C(0x2)
- /*
- * This bit must be '1' for the max_agg_timer field to be
- * configured.
- */
- #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGG_TIMER UINT32_C(0x4)
- /* This bit must be '1' for the min_agg_len field to be configured. */
- #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MIN_AGG_LEN UINT32_C(0x8)
- uint16_t vnic_id;
- /* Logical vnic ID */
- uint16_t max_agg_segs;
- /*
- * This is the maximum number of TCP segments that can be
- * aggregated (unit is Log2). Max value is 31.
- */
- /* 1 segment */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_1 UINT32_C(0x0)
- /* 2 segments */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_2 UINT32_C(0x1)
- /* 4 segments */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_4 UINT32_C(0x2)
- /* 8 segments */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_8 UINT32_C(0x3)
- /* Any segment size larger than this is not valid */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_MAX UINT32_C(0x1f)
- uint16_t max_aggs;
- /*
- * This is the maximum number of aggregations this VNIC is
- * allowed (unit is Log2). Max value is 7
- */
- /* 1 aggregation */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_1 UINT32_C(0x0)
- /* 2 aggregations */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_2 UINT32_C(0x1)
- /* 4 aggregations */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_4 UINT32_C(0x2)
- /* 8 aggregations */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_8 UINT32_C(0x3)
- /* 16 aggregations */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_16 UINT32_C(0x4)
- /* Any aggregation size larger than this is not valid */
- #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_MAX UINT32_C(0x7)
- uint8_t unused_0;
- uint8_t unused_1;
- uint32_t max_agg_timer;
+ uint32_t encap_request[26];
/*
- * This is the maximum amount of time allowed for an aggregation
- * context to complete after it was initiated.
+ * This is an encapsulated request. This request should be
+ * executed by the HWRM and the response should be provided in
+ * the response buffer inside the encapsulated request.
*/
- uint32_t min_agg_len;
+ uint16_t encap_resp_target_id;
/*
- * This is the minimum amount of payload length required to
- * start an aggregation context.
+ * This value indicates the target id of the response to the
+ * encapsulated request. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF -
+ * HWRM
*/
+ uint16_t unused_0[3];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_vnic_tpa_cfg_output {
+/* Output (16 bytes) */
+struct hwrm_exec_fwd_resp_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -8244,12 +25227,18 @@ struct hwrm_vnic_tpa_cfg_output {
*/
} __attribute__((packed));
-/* hwrm_ring_alloc */
+/* hwrm_reject_fwd_resp */
/*
- * Description: This command allocates and does basic preparation for a ring.
+ * Description: This command is used to send an encapsulated request to the
+ * HWRM. This command instructs the HWRM to reject the request and forward the
+ * error response of the encapsulated request to the location specified in the
+ * original request that is encapsulated. The target id of this command shall be
+ * set to 0xFFFF (HWRM). The response location in this command shall be used to
+ * acknowledge the receipt of the encapsulated request and forwarding of the
+ * response.
*/
-/* Input (80 bytes) */
-struct hwrm_ring_alloc_input {
+/* Input (128 bytes) */
+struct hwrm_reject_fwd_resp_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -8276,201 +25265,25 @@ struct hwrm_ring_alloc_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t enables;
- /* This bit must be '1' for the Reserved1 field to be configured. */
- #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED1 UINT32_C(0x1)
- /* This bit must be '1' for the ring_arb_cfg field to be configured. */
- #define HWRM_RING_ALLOC_INPUT_ENABLES_RING_ARB_CFG UINT32_C(0x2)
- /* This bit must be '1' for the Reserved3 field to be configured. */
- #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED3 UINT32_C(0x4)
- /*
- * This bit must be '1' for the stat_ctx_id_valid field to be
- * configured.
- */
- #define HWRM_RING_ALLOC_INPUT_ENABLES_STAT_CTX_ID_VALID UINT32_C(0x8)
- /* This bit must be '1' for the Reserved4 field to be configured. */
- #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED4 UINT32_C(0x10)
- /* This bit must be '1' for the max_bw_valid field to be configured. */
- #define HWRM_RING_ALLOC_INPUT_ENABLES_MAX_BW_VALID UINT32_C(0x20)
- uint8_t ring_type;
- /* Ring Type. */
- /* L2 Completion Ring (CR) */
- #define HWRM_RING_ALLOC_INPUT_RING_TYPE_L2_CMPL UINT32_C(0x0)
- /* TX Ring (TR) */
- #define HWRM_RING_ALLOC_INPUT_RING_TYPE_TX UINT32_C(0x1)
- /* RX Ring (RR) */
- #define HWRM_RING_ALLOC_INPUT_RING_TYPE_RX UINT32_C(0x2)
- /* RoCE Notification Completion Ring (ROCE_CR) */
- #define HWRM_RING_ALLOC_INPUT_RING_TYPE_ROCE_CMPL UINT32_C(0x3)
- uint8_t unused_0;
- uint16_t unused_1;
- uint64_t page_tbl_addr;
- /* This value is a pointer to the page table for the Ring. */
- uint32_t fbo;
- /* First Byte Offset of the first entry in the first page. */
- uint8_t page_size;
- /*
- * Actual page size in 2^page_size. The supported range is
- * increments in powers of 2 from 16 bytes to 1GB. - 4 = 16 B
- * Page size is 16 B. - 12 = 4 KB Page size is 4 KB. - 13 = 8 KB
- * Page size is 8 KB. - 16 = 64 KB Page size is 64 KB. - 21 = 2
- * MB Page size is 2 MB. - 22 = 4 MB Page size is 4 MB. - 30 = 1
- * GB Page size is 1 GB.
- */
- uint8_t page_tbl_depth;
- /*
- * This value indicates the depth of page table. For this
- * version of the specification, value other than 0 or 1 shall
- * be considered as an invalid value. When the page_tbl_depth =
- * 0, then it is treated as a special case with the following.
- * 1. FBO and page size fields are not valid. 2. page_tbl_addr
- * is the physical address of the first element of the ring.
- */
- uint8_t unused_2;
- uint8_t unused_3;
- uint32_t length;
- /*
- * Number of 16B units in the ring. Minimum size for a ring is
- * 16 16B entries.
- */
- uint16_t logical_id;
- /*
- * Logical ring number for the ring to be allocated. This value
- * determines the position in the doorbell area where the update
- * to the ring will be made. For completion rings, this value is
- * also the MSI-X vector number for the function the completion
- * ring is associated with.
- */
- uint16_t cmpl_ring_id;
- /*
- * This field is used only when ring_type is a TX ring. This
- * value indicates what completion ring the TX ring is
- * associated with.
- */
- uint16_t queue_id;
- /*
- * This field is used only when ring_type is a TX ring. This
- * value indicates what CoS queue the TX ring is associated
- * with.
- */
- uint8_t unused_4;
- uint8_t unused_5;
- uint32_t reserved1;
- /* This field is reserved for the future use. It shall be set to 0. */
- uint16_t ring_arb_cfg;
- /*
- * This field is used only when ring_type is a TX ring. This
- * field is used to configure arbitration related parameters for
- * a TX ring.
- */
- /* Arbitration policy used for the ring. */
- #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_MASK UINT32_C(0xf)
- #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_SFT 0
- /*
- * Use strict priority for the TX ring. Priority
- * value is specified in arb_policy_param
- */
- #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_SP \
- (UINT32_C(0x1) << 0)
- /*
- * Use weighted fair queue arbitration for the
- * TX ring. Weight is specified in
- * arb_policy_param
- */
- #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_WFQ \
- (UINT32_C(0x2) << 0)
- #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_LAST \
- RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_WFQ
- /* Reserved field. */
- #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_RSVD_MASK UINT32_C(0xf0)
- #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_RSVD_SFT 4
- /*
- * Arbitration policy specific parameter. # For strict priority
- * arbitration policy, this field represents a priority value.
- * If set to 0, then the priority is not specified and the HWRM
- * is allowed to select any priority for this TX ring. # For
- * weighted fair queue arbitration policy, this field represents
- * a weight value. If set to 0, then the weight is not specified
- * and the HWRM is allowed to select any weight for this TX
- * ring.
- */
- #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_PARAM_MASK \
- UINT32_C(0xff00)
- #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_PARAM_SFT 8
- uint8_t unused_6;
- uint8_t unused_7;
- uint32_t reserved3;
- /* This field is reserved for the future use. It shall be set to 0. */
- uint32_t stat_ctx_id;
- /*
- * This field is used only when ring_type is a TX ring. This
- * input indicates what statistics context this ring should be
- * associated with.
- */
- uint32_t reserved4;
- /* This field is reserved for the future use. It shall be set to 0. */
- uint32_t max_bw;
+ uint32_t encap_request[26];
/*
- * This field is used only when ring_type is a TX ring to
- * specify maximum BW allocated to the TX ring. The HWRM will
- * translate this value into byte counter and time interval used
- * for this ring inside the device.
+ * This is an encapsulated request. This request should be
+ * rejected by the HWRM and the error response should be
+ * provided in the response buffer inside the encapsulated
+ * request.
*/
- /* The bandwidth value. */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_SFT 0
- /* The granularity of the value (bits or bytes). */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE UINT32_C(0x10000000)
- /* Value is in bits. */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BITS (UINT32_C(0x0) << 28)
- /* Value is in bytes. */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BYTES (UINT32_C(0x1) << 28)
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_LAST \
- RING_ALLOC_INPUT_MAX_BW_SCALE_BYTES
- /* bw_value_unit is 3 b */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_MASK \
- UINT32_C(0xe0000000)
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
- /* Value is in Mb or MB (base 10). */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
- (UINT32_C(0x0) << 29)
- /* Value is in Kb or KB (base 10). */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_KILO \
- (UINT32_C(0x2) << 29)
- /* Value is in bits or bytes. */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_BASE \
- (UINT32_C(0x4) << 29)
- /* Value is in Gb or GB (base 10). */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
- (UINT32_C(0x6) << 29)
- /* Value is in 1/100th of a percentage of total bandwidth. */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
- (UINT32_C(0x1) << 29)
- /* Invalid unit */
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
- (UINT32_C(0x7) << 29)
- #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
- RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
- uint8_t int_mode;
+ uint16_t encap_resp_target_id;
/*
- * This field is used only when ring_type is a Completion ring.
- * This value indicates what interrupt mode should be used on
- * this completion ring. Note: In the legacy interrupt mode, no
- * more than 16 completion rings are allowed.
- */
- /* Legacy INTA */
- #define HWRM_RING_ALLOC_INPUT_INT_MODE_LEGACY UINT32_C(0x0)
- /* Reserved */
- #define HWRM_RING_ALLOC_INPUT_INT_MODE_RSVD UINT32_C(0x1)
- /* MSI-X */
- #define HWRM_RING_ALLOC_INPUT_INT_MODE_MSIX UINT32_C(0x2)
- /* No Interrupt - Polled mode */
- #define HWRM_RING_ALLOC_INPUT_INT_MODE_POLL UINT32_C(0x3)
- uint8_t unused_8[3];
+ * This value indicates the target id of the response to the
+ * encapsulated request. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF -
+ * HWRM
+ */
+ uint16_t unused_0[3];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_ring_alloc_output {
+/* Output (16 bytes) */
+struct hwrm_reject_fwd_resp_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -8486,16 +25299,10 @@ struct hwrm_ring_alloc_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint16_t ring_id;
- /*
- * Physical number of ring allocated. This value shall be unique
- * for a ring type.
- */
- uint16_t logical_ring_id;
- /* Logical number of ring allocated. */
- uint8_t unused_0;
+ uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -8507,20 +25314,16 @@ struct hwrm_ring_alloc_output {
*/
} __attribute__((packed));
-/* hwrm_ring_free */
+/* hwrm_fwd_resp */
/*
- * Description: This command is used to free a ring and associated resources.
- * With QoS and DCBx agents, it is possible the traffic classes will be moved
- * from one CoS queue to another. When this occurs, the driver shall call
- * 'hwrm_ring_free' to free the allocated rings and then call 'hwrm_ring_alloc'
- * to re-allocate each ring and assign it to a new CoS queue. hwrm_ring_free
- * shall be called on a ring only after it has been idle for 500ms or more and
- * no frames have been posted to the ring during this time. All frames queued
- * for transmission shall be completed and at least 500ms time elapsed from the
- * last completion before calling this command.
+ * Description: This command is used to send an encapsulated response to the
+ * HWRM. The HWRM shall forward this response based on the target id. The
+ * response address provided in this command shall be used to acknowledge the
+ * receipt of the encapsulated response. The encapsulated response address
+ * provided in this command shall be used to provide the encapsulated response.
*/
-/* Input (24 bytes) */
-struct hwrm_ring_free_input {
+/* Input (40 bytes) */
+struct hwrm_fwd_resp_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -8547,24 +25350,37 @@ struct hwrm_ring_free_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint8_t ring_type;
- /* Ring Type. */
- /* L2 Completion Ring (CR) */
- #define HWRM_RING_FREE_INPUT_RING_TYPE_L2_CMPL UINT32_C(0x0)
- /* TX Ring (TR) */
- #define HWRM_RING_FREE_INPUT_RING_TYPE_TX UINT32_C(0x1)
- /* RX Ring (RR) */
- #define HWRM_RING_FREE_INPUT_RING_TYPE_RX UINT32_C(0x2)
- /* RoCE Notification Completion Ring (ROCE_CR) */
- #define HWRM_RING_FREE_INPUT_RING_TYPE_ROCE_CMPL UINT32_C(0x3)
+ uint16_t encap_resp_target_id;
+ /*
+ * This value indicates the target id of the encapsulated
+ * response. 0x0 - 0xFFF8 - Used for function ids 0xFFF8 -
+ * 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t encap_resp_cmpl_ring;
+ /*
+ * This value indicates the completion ring the encapsulated
+ * response will be optionally completed on. If the value is -1,
+ * then no CR completion shall be generated for the encapsulated
+ * response. Any other value must be a valid CR ring_id value.
+ * If a valid encap_resp_cmpl_ring is provided, then a CR
+ * completion shall be generated for the encapsulated response.
+ */
+ uint16_t encap_resp_len;
+ /* This field indicates the length of encapsulated response. */
uint8_t unused_0;
- uint16_t ring_id;
- /* Physical number of ring allocated. */
- uint32_t unused_1;
+ uint8_t unused_1;
+ uint64_t encap_resp_addr;
+ /*
+ * This is the host address where the encapsulated response will
+ * be written. This area must be 16B aligned and must be cleared
+ * to zero before the original request is made.
+ */
+ uint32_t encap_resp[24];
+ /* This is an encapsulated response. */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_ring_free_output {
+/* Output (16 bytes) */
+struct hwrm_fwd_resp_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -8595,12 +25411,16 @@ struct hwrm_ring_free_output {
*/
} __attribute__((packed));
-/* hwrm_ring_grp_alloc */
+/* hwrm_fwd_async_event_cmpl */
/*
- * Description: This API allocates and does basic preparation for a ring group.
+ * Description: This command is used to send an encapsulated asynchronous event
+ * completion to the HWRM. The HWRM shall forward this asynchronous event
+ * completion to target(s) specified in the command. The HWRM shall complete
+ * this command only after forwarding asynchronous event completion to specified
+ * targets.
*/
-/* Input (24 bytes) */
-struct hwrm_ring_grp_alloc_input {
+/* Input (32 bytes) */
+struct hwrm_fwd_async_event_cmpl_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -8627,25 +25447,24 @@ struct hwrm_ring_grp_alloc_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint16_t cr;
- /* This value identifies the CR associated with the ring group. */
- uint16_t rr;
- /* This value identifies the main RR associated with the ring group. */
- uint16_t ar;
- /*
- * This value identifies the aggregation RR associated with the
- * ring group. If this value is 0xFF... (All Fs), then no
- * Aggregation ring will be set.
- */
- uint16_t sc;
+ uint16_t encap_async_event_target_id;
/*
- * This value identifies the statistics context associated with
- * the ring group.
+ * This value indicates the target id of the encapsulated
+ * asynchronous event. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF -
+ * Broadcast to all children VFs (only applicable when a PF is
+ * the requester)
*/
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2[3];
+ uint8_t unused_3;
+ uint32_t encap_async_event_cmpl[4];
+ /* This is an encapsulated asynchronous event completion. */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_ring_grp_alloc_output {
+/* Output (16 bytes) */
+struct hwrm_fwd_async_event_cmpl_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -8661,15 +25480,10 @@ struct hwrm_ring_grp_alloc_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t ring_group_id;
- /*
- * This is the ring group ID value. Use this value to program
- * the default ring group for the VNIC or as table entries in an
- * RSS/COS context.
- */
- uint8_t unused_0;
+ uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -8681,17 +25495,12 @@ struct hwrm_ring_grp_alloc_output {
*/
} __attribute__((packed));
-/* hwrm_ring_grp_free */
+/* hwrm_temp_monitor_query */
/*
- * Description: This API frees a ring group and associated resources. # If a
- * ring in the ring group is reset or free, then the associated rings in the
- * ring group shall also be reset/free using hwrm_ring_free. # A function driver
- * shall always use hwrm_ring_grp_free after freeing all rings in a group. # As
- * a part of executing this command, the HWRM shall reset all associated ring
- * group resources.
+ * Description: A temperature monitor is used to query the device temperature.
*/
-/* Input (24 bytes) */
-struct hwrm_ring_grp_free_input {
+/* Input (16 bytes) */
+struct hwrm_temp_monitor_query_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -8718,13 +25527,10 @@ struct hwrm_ring_grp_free_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t ring_group_id;
- /* This is the ring group ID value. */
- uint32_t unused_0;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_ring_grp_free_output {
+/* Output (16 bytes) */
+struct hwrm_temp_monitor_query_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -8740,10 +25546,16 @@ struct hwrm_ring_grp_free_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t unused_0;
- uint8_t unused_1;
+ uint8_t temp;
+ /*
+ * The HWRM shall provide the current temperature of device in
+ * Celsius.
+ */
+ uint8_t unused_0;
+ uint16_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
+ uint8_t unused_4;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -8755,64 +25567,22 @@ struct hwrm_ring_grp_free_output {
*/
} __attribute__((packed));
-/* hwrm_cfa_l2_filter_alloc */
+/* hwrm_wol_filter_alloc */
/*
- * Description: An L2 filter is a filter resource that is used to identify a
- * vnic or ring for a packet based on layer 2 fields. Layer 2 fields for
- * encapsulated packets include both outer L2 header and/or inner l2 header of
- * encapsulated packet. The L2 filter resource covers the following OS specific
- * L2 filters. Linux/FreeBSD (per function): # Broadcast enable/disable # List
- * of individual multicast filters # All multicast enable/disable filter #
- * Unicast filters # Promiscuous mode VMware: # Broadcast enable/disable (per
- * physical function) # All multicast enable/disable (per function) # Unicast
- * filters per ring or vnic # Promiscuous mode per PF Windows: # Broadcast
- * enable/disable (per physical function) # List of individual multicast filters
- * (Driver needs to advertise the maximum number of filters supported) # All
- * multicast enable/disable per physical function # Unicast filters per vnic #
- * Promiscuous mode per PF Implementation notes on the use of VNIC in this
- * command: # By default, these filters belong to default vnic for the function.
- * # Once these filters are set up, only destination VNIC can be modified. # If
- * the destination VNIC is not specified in this command, then the HWRM shall
- * only create an l2 context id. HWRM Implementation notes for multicast
- * filters: # The hwrm_filter_alloc command can be used to set up multicast
- * filters (perfect match or partial match). Each individual function driver can
- * set up multicast filters independently. # The HWRM needs to keep track of
- * multicast filters set up by function drivers and maintain multicast group
- * replication records to enable a subset of functions to receive traffic for a
- * specific multicast address. # When a specific multicast filter cannot be set,
- * the HWRM shall return an error. In this error case, the driver should fall
- * back to using one general filter (rather than specific) for all multicast
- * traffic. # When the SR-IOV is enabled, the HWRM needs to additionally track
- * source knockout per multicast group record. Examples of setting unicast
- * filters: For a unicast MAC based filter, one can use a combination of the
- * fields and masks provided in this command to set up the filter. Below are
- * some examples: # MAC + no VLAN filter: This filter is used to identify
- * traffic that does not contain any VLAN tags and matches destination (or
- * source) MAC address. This filter can be set up by setting only l2_addr field
- * to be a valid field. All other fields are not valid. The following value is
- * set for l2_addr. l2_addr = MAC # MAC + Any VLAN filter: This filter is used
- * to identify traffic that carries single VLAN tag and matches (destination or
- * source) MAC address. This filter can be set up by setting only l2_addr and
- * l2_ovlan_mask fields to be valid fields. All other fields are not valid. The
- * following values are set for those two valid fields. l2_addr = MAC,
- * l2_ovlan_mask = 0xFFFF # MAC + no VLAN or VLAN ID=0: This filter is used to
- * identify untagged traffic that does not contain any VLAN tags or a VLAN tag
- * with VLAN ID = 0 and matches destination (or source) MAC address. This filter
- * can be set up by setting only l2_addr and l2_ovlan fields to be valid fields.
- * All other fields are not valid. The following value are set for l2_addr and
- * l2_ovlan. l2_addr = MAC, l2_ovlan = 0x0 # MAC + no VLAN or any VLAN: This
- * filter is used to identify traffic that contains zero or 1 VLAN tag and
- * matches destination (or source) MAC address. This filter can be set up by
- * setting only l2_addr, l2_ovlan, and l2_mask fields to be valid fields. All
- * other fields are not valid. The following value are set for l2_addr,
- * l2_ovlan, and l2_mask fields. l2_addr = MAC, l2_ovlan = 0x0, l2_ovlan_mask =
- * 0xFFFF # MAC + VLAN ID filter: This filter can be set up by setting only
- * l2_addr, l2_ovlan, and l2_ovlan_mask fields to be valid fields. All other
- * fields are not valid. The following values are set for those three valid
- * fields. l2_addr = MAC, l2_ovlan = VLAN ID, l2_ovlan_mask = 0xF000
+ * Description: A Wake-On-LAN (WoL) filter is a filter resource that is used to
+ * identify a WoL packet. # Among all function drivers, the HWRM shall only
+ * allow PF drivers to allocate WoL filters. # The HWRM shall not allow VF
+ * drivers to allocate any WoL filters. # When partitioning is enabled and WoL
+ * is supported, the HWRM shall support at least one WoL filter per partition. #
+ * The HWRM shall retain a WoL filter setting until the filter is freed. # If
+ * the HWRM client is a function driver, then the HWRM shall not allow the HWRM
+ * client to set up WoL filters on the port that the function is not associated
+ * with. # If the HWRM client is one of the trusted embedded services (e.g.
+ * management service), the the HWRM shall allow the HWRM client to set up WoL
+ * filters on any port of the device.
*/
-/* Input (96 bytes) */
-struct hwrm_cfa_l2_filter_alloc_input {
+/* Input (64 bytes) */
+struct hwrm_wol_filter_alloc_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -8825,272 +25595,96 @@ struct hwrm_cfa_l2_filter_alloc_input {
* CR completion will be generated. Any other value must be a
* valid CR ring_id value for this function.
*/
- uint16_t seq_id;
- /* This value indicates the command sequence number. */
- uint16_t target_id;
- /*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function
- * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
- * - HWRM
- */
- uint64_t resp_addr;
- /*
- * This is the host address where the response will be written
- * when the request is complete. This area must be 16B aligned
- * and must be cleared to zero before the request is made.
- */
- uint32_t flags;
- /*
- * Enumeration denoting the RX, TX type of the resource. This
- * enumeration is used for resources that are similar for both
- * TX and RX paths of the chip.
- */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH UINT32_C(0x1)
- /* tx path */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_TX \
- (UINT32_C(0x0) << 0)
- /* rx path */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX \
- (UINT32_C(0x1) << 0)
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_LAST \
- CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX
- /*
- * Setting of this flag indicates the applicability to the
- * loopback path.
- */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK UINT32_C(0x2)
- /*
- * Setting of this flag indicates drop action. If this flag is
- * not set, then it should be considered accept action.
- */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_DROP UINT32_C(0x4)
- /*
- * If this flag is set, all t_l2_* fields are invalid and they
- * should not be specified. If this flag is set, then l2_*
- * fields refer to fields of outermost L2 header.
- */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_OUTERMOST UINT32_C(0x8)
- uint32_t enables;
- /* This bit must be '1' for the l2_addr field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR UINT32_C(0x1)
- /* This bit must be '1' for the l2_addr_mask field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR_MASK \
- UINT32_C(0x2)
- /* This bit must be '1' for the l2_ovlan field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN UINT32_C(0x4)
- /*
- * This bit must be '1' for the l2_ovlan_mask field to be
- * configured.
- */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN_MASK \
- UINT32_C(0x8)
- /* This bit must be '1' for the l2_ivlan field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN UINT32_C(0x10)
- /*
- * This bit must be '1' for the l2_ivlan_mask field to be
- * configured.
- */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN_MASK \
- UINT32_C(0x20)
- /* This bit must be '1' for the t_l2_addr field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR UINT32_C(0x40)
- /*
- * This bit must be '1' for the t_l2_addr_mask field to be
- * configured.
- */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR_MASK \
- UINT32_C(0x80)
- /* This bit must be '1' for the t_l2_ovlan field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN \
- UINT32_C(0x100)
- /*
- * This bit must be '1' for the t_l2_ovlan_mask field to be
- * configured.
- */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN_MASK \
- UINT32_C(0x200)
- /* This bit must be '1' for the t_l2_ivlan field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN \
- UINT32_C(0x400)
- /*
- * This bit must be '1' for the t_l2_ivlan_mask field to be
- * configured.
- */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN_MASK \
- UINT32_C(0x800)
- /* This bit must be '1' for the src_type field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_TYPE UINT32_C(0x1000)
- /* This bit must be '1' for the src_id field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_ID UINT32_C(0x2000)
- /* This bit must be '1' for the tunnel_type field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
- UINT32_C(0x4000)
- /* This bit must be '1' for the dst_id field to be configured. */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_DST_ID UINT32_C(0x8000)
- /*
- * This bit must be '1' for the mirror_vnic_id field to be
- * configured.
- */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
- UINT32_C(0x10000)
- uint8_t l2_addr[6];
- /*
- * This value sets the match value for the L2 MAC address.
- * Destination MAC address for RX path. Source MAC address for
- * TX path.
- */
- uint8_t unused_0;
- uint8_t unused_1;
- uint8_t l2_addr_mask[6];
- /*
- * This value sets the mask value for the L2 address. A value of
- * 0 will mask the corresponding bit from compare.
- */
- uint16_t l2_ovlan;
- /* This value sets VLAN ID value for outer VLAN. */
- uint16_t l2_ovlan_mask;
- /*
- * This value sets the mask value for the ovlan id. A value of 0
- * will mask the corresponding bit from compare.
- */
- uint16_t l2_ivlan;
- /* This value sets VLAN ID value for inner VLAN. */
- uint16_t l2_ivlan_mask;
- /*
- * This value sets the mask value for the ivlan id. A value of 0
- * will mask the corresponding bit from compare.
- */
- uint8_t unused_2;
- uint8_t unused_3;
- uint8_t t_l2_addr[6];
- /*
- * This value sets the match value for the tunnel L2 MAC
- * address. Destination MAC address for RX path. Source MAC
- * address for TX path.
- */
- uint8_t unused_4;
- uint8_t unused_5;
- uint8_t t_l2_addr_mask[6];
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * This value sets the mask value for the tunnel L2 address. A
- * value of 0 will mask the corresponding bit from compare.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint16_t t_l2_ovlan;
- /* This value sets VLAN ID value for tunnel outer VLAN. */
- uint16_t t_l2_ovlan_mask;
+ uint64_t resp_addr;
/*
- * This value sets the mask value for the tunnel ovlan id. A
- * value of 0 will mask the corresponding bit from compare.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint16_t t_l2_ivlan;
- /* This value sets VLAN ID value for tunnel inner VLAN. */
- uint16_t t_l2_ivlan_mask;
+ uint32_t flags;
+ uint32_t enables;
+ /* This bit must be '1' for the mac_address field to be configured. */
+ #define HWRM_WOL_FILTER_ALLOC_INPUT_ENABLES_MAC_ADDRESS 0x1UL
/*
- * This value sets the mask value for the tunnel ivlan id. A
- * value of 0 will mask the corresponding bit from compare.
+ * This bit must be '1' for the pattern_offset field to be
+ * configured.
*/
- uint8_t src_type;
- /* This value identifies the type of source of the packet. */
- /* Network port */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_NPORT UINT32_C(0x0)
- /* Physical function */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_PF UINT32_C(0x1)
- /* Virtual function */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VF UINT32_C(0x2)
- /* Virtual NIC of a function */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VNIC UINT32_C(0x3)
- /* Embedded processor for CFA management */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_KONG UINT32_C(0x4)
- /* Embedded processor for OOB management */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_APE UINT32_C(0x5)
- /* Embedded processor for RoCE */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_BONO UINT32_C(0x6)
- /* Embedded processor for network proxy functions */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_TANG UINT32_C(0x7)
- uint8_t unused_6;
- uint32_t src_id;
+ #define HWRM_WOL_FILTER_ALLOC_INPUT_ENABLES_PATTERN_OFFSET 0x2UL
/*
- * This value is the id of the source. For a network port, it
- * represents port_id. For a physical function, it represents
- * fid. For a virtual function, it represents vf_id. For a vnic,
- * it represents vnic_id. For embedded processors, this id is
- * not valid. Notes: 1. The function ID is implied if it src_id
- * is not provided for a src_type that is either
+ * This bit must be '1' for the pattern_buf_size field to be
+ * configured.
*/
- uint8_t tunnel_type;
- /* Tunnel Type. */
- /* Non-tunnel */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
- UINT32_C(0x0)
- /* Virtual eXtensible Local Area Network (VXLAN) */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
- UINT32_C(0x1)
+ #define HWRM_WOL_FILTER_ALLOC_INPUT_ENABLES_PATTERN_BUF_SIZE 0x4UL
/*
- * Network Virtualization Generic Routing
- * Encapsulation (NVGRE)
+ * This bit must be '1' for the pattern_buf_addr field to be
+ * configured.
*/
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
- UINT32_C(0x2)
+ #define HWRM_WOL_FILTER_ALLOC_INPUT_ENABLES_PATTERN_BUF_ADDR 0x8UL
/*
- * Generic Routing Encapsulation (GRE) inside
- * Ethernet payload
+ * This bit must be '1' for the pattern_mask_addr field to be
+ * configured.
*/
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE UINT32_C(0x3)
- /* IP in IP */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP UINT32_C(0x4)
- /* Generic Network Virtualization Encapsulation (Geneve) */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE UINT32_C(0x5)
- /* Multi-Protocol Lable Switching (MPLS) */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS UINT32_C(0x6)
- /* Stateless Transport Tunnel (STT) */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT UINT32_C(0x7)
- /*
- * Generic Routing Encapsulation (GRE) inside IP
- * datagram payload
+ #define HWRM_WOL_FILTER_ALLOC_INPUT_ENABLES_PATTERN_MASK_ADDR 0x10UL
+ /*
+ * This bit must be '1' for the pattern_mask_size field to be
+ * configured.
*/
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE UINT32_C(0x8)
- /* Any tunneled traffic */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
- UINT32_C(0xff)
- uint8_t unused_7;
- uint16_t dst_id;
+ #define HWRM_WOL_FILTER_ALLOC_INPUT_ENABLES_PATTERN_MASK_SIZE 0x20UL
+ uint16_t port_id;
+ /* Port ID of port on which WoL filter is configured. */
+ uint8_t wol_type;
+ /* This value represents a Wake-on-LAN type. */
+ /* Magic Paket */
+ #define HWRM_WOL_FILTER_ALLOC_INPUT_WOL_TYPE_MAGICPKT 0x0UL
+ /* Bitmap */
+ #define HWRM_WOL_FILTER_ALLOC_INPUT_WOL_TYPE_BMP 0x1UL
+ /* Invalid */
+ #define HWRM_WOL_FILTER_ALLOC_INPUT_WOL_TYPE_INVALID 0xffUL
+ uint8_t unused_0;
+ uint32_t unused_1;
+ uint8_t mac_address[6];
/*
- * If set, this value shall represent the Logical VNIC ID of the
- * destination VNIC for the RX path and network port id of the
- * destination port for the TX path.
+ * # If this field is enabled and magic packet WoL filter type
+ * is specified in this command, the value set in this field
+ * shall be used in setting the magic packet based WoL filter. #
+ * If this field is not enabled and magic packet WoL filter type
+ * is specified and port id is specified to 0xFF in this
+ * command, then the HWRM shall use default MAC address
+ * configured on the function associated with the HWRM client. #
+ * If this field is not enabled and magic packet WoL filter type
+ * is specified and port id is not specified to 0xFF in this
+ * command, then the HWRM shall use default MAC address
+ * configured on the port.
*/
- uint16_t mirror_vnic_id;
- /* Logical VNIC ID of the VNIC where traffic is mirrored. */
- uint8_t pri_hint;
+ uint16_t pattern_offset;
/*
- * This hint is provided to help in placing the filter in the
- * filter table.
+ * The offset from the beginning of MAC header where pattern
+ * should be matched. Applies to bitmap WoL.
*/
- /* No preference */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER \
- UINT32_C(0x0)
- /* Above the given filter */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE_FILTER \
- UINT32_C(0x1)
- /* Below the given filter */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_BELOW_FILTER \
- UINT32_C(0x2)
- /* As high as possible */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MAX UINT32_C(0x3)
- /* As low as possible */
- #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MIN UINT32_C(0x4)
- uint8_t unused_8;
- uint32_t unused_9;
- uint64_t l2_filter_id_hint;
+ uint16_t pattern_buf_size;
/*
- * This is the ID of the filter that goes along with the
- * pri_hint. This field is valid only for the following values.
- * 1 - Above the given filter 2 - Below the given filter
+ * The size of the pattern that is being matched. Applies to
+ * bitmap WoL.
*/
+ uint16_t pattern_mask_size;
+ /* The size of the pattern mask. Applies to bitmap WoL. */
+ uint32_t unused_2;
+ uint64_t pattern_buf_addr;
+ /* Physical address of the pattern buffer. Applies to bitmap WoL. */
+ uint64_t pattern_mask_addr;
+ /* Physical address of the pattern mask. Applies to bitmap WoL. */
} __attribute__((packed));
-/* Output (24 bytes) */
-struct hwrm_cfa_l2_filter_alloc_output {
+/* Output (16 bytes) */
+struct hwrm_wol_filter_alloc_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -9106,21 +25700,13 @@ struct hwrm_cfa_l2_filter_alloc_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint64_t l2_filter_id;
- /*
- * This value identifies a set of CFA data structures used for
- * an L2 context.
- */
- uint32_t flow_id;
- /*
- * This is the ID of the flow associated with this filter. This
- * value shall be used to match and associate the flow
- * identifier returned in completion records. A value of
- * 0xFFFFFFFF shall indicate no flow id.
- */
+ uint8_t wol_filter_id;
+ /* This value identifies a Wake-on-LAN (WoL) filter. */
uint8_t unused_0;
- uint8_t unused_1;
+ uint16_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -9132,13 +25718,18 @@ struct hwrm_cfa_l2_filter_alloc_output {
*/
} __attribute__((packed));
-/* hwrm_cfa_l2_filter_free */
+/* hwrm_wol_filter_free */
/*
- * Description: Free a L2 filter. The HWRM shall free all associated filter
- * resources with the L2 filter.
+ * Description: Free a WoL filter. # Among all function drivers, the HWRM shall
+ * only allow PF drivers to free WoL filters. # The HWRM shall not allow VF
+ * drivers to free any WoL filters. # The HWRM shall not allow a function driver
+ * to free an Out-Of-Box WoL filter. # The HWRM shall not allow a function
+ * driver to free a WoL filter on a port that the corresponding function is not
+ * associated with. # The HWRM shall not allow a function driver to free a WoL
+ * filter on a function that the function driver is not associated with.
*/
-/* Input (24 bytes) */
-struct hwrm_cfa_l2_filter_free_input {
+/* Input (32 bytes) */
+struct hwrm_wol_filter_free_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -9165,15 +25756,33 @@ struct hwrm_cfa_l2_filter_free_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint64_t l2_filter_id;
+ uint32_t flags;
/*
- * This value identifies a set of CFA data structures used for
- * an L2 context.
+ * # When this bit is set to '1', then all active WoL filters on
+ * the port are requested to be freed. # If the a function
+ * driver sets this flag to '1', then the HWRM shall free all
+ * active WoL filters that are not set by other function drivers
+ * on that port.
+ */
+ #define HWRM_WOL_FILTER_FREE_INPUT_FLAGS_FREE_ALL_WOL_FILTERS 0x1UL
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the wol_filter_id field to be
+ * configured.
+ */
+ #define HWRM_WOL_FILTER_FREE_INPUT_ENABLES_WOL_FILTER_ID 0x1UL
+ uint16_t port_id;
+ /* Port ID of the port on which WoL filter(s) is (are) being freed. */
+ uint8_t wol_filter_id;
+ /*
+ * The HWRM shall ignore this field if free_all_wol_filters flag
+ * is set.
*/
+ uint8_t unused_0[5];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_cfa_l2_filter_free_output {
+/* Output (16 bytes) */
+struct hwrm_wol_filter_free_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -9204,10 +25813,22 @@ struct hwrm_cfa_l2_filter_free_output {
*/
} __attribute__((packed));
-/* hwrm_cfa_l2_filter_cfg */
-/* Description: Change the configuration of an existing L2 filter */
-/* Input (40 bytes) */
-struct hwrm_cfa_l2_filter_cfg_input {
+/* hwrm_wol_filter_qcfg */
+/*
+ * Description: Query WoL filter configuration. # Among all function drivers,
+ * the HWRM shall only allow PF drivers to query WoL filters. # The HWRM shall
+ * not allow VF drivers to query any WoL filters. # The HWRM shall return WoL
+ * filters that are active on the associated port for which this query is being
+ * performed. # If the HWRM client is a function driver, then the HWRM shall not
+ * allow the HWRM client to query WoL filters that are set up by other function
+ * drivers. # If the HWRM client is a function driver, then the HWRM shall not
+ * allow the HWRM client to query WoL filters on the port that the function is
+ * not associated with. # If the HWRM client is one of the trusted embedded
+ * service (e.g. management service), the the HWRM shall allow the HWRM client
+ * to query WoL filters on any port of the device.
+ */
+/* Input (56 bytes) */
+struct hwrm_wol_filter_qcfg_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -9234,52 +25855,56 @@ struct hwrm_cfa_l2_filter_cfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t flags;
+ uint16_t port_id;
+ /* Port ID of port on which WoL filter that is being queried. */
+ uint16_t handle;
/*
- * Enumeration denoting the RX, TX type of the resource. This
- * enumeration is used for resources that are similar for both
- * TX and RX paths of the chip.
+ * This is an opaque handle used to access filters. # The HWRM
+ * client shall set this field to 0x0000 to begin the query. #
+ * After the first query, the HWRM client shall retrieve next
+ * filters (if they exist) using the HWRM provided handle in the
+ * response.
*/
- #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH UINT32_C(0x1)
- /* tx path */
- #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_TX \
- (UINT32_C(0x0) << 0)
- /* rx path */
- #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_RX \
- (UINT32_C(0x1) << 0)
- #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_LAST \
- CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_RX
+ uint32_t unused_0;
+ uint64_t pattern_buf_addr;
/*
- * Setting of this flag indicates drop action. If this flag is
- * not set, then it should be considered accept action.
+ * Physical address of the pattern buffer. Applies to bitmap WoL
+ * filter only. # Value of 0 indicates an invalid buffer
+ * address. If this field is set to 0, then HWRM shall ignore
+ * pattern_buf_size. # If the HWRM client provides an invalid
+ * buffer address for the pattern, then the HWRM is not required
+ * to provide pattern when the response contains a bitmap WoL
+ * filter.
*/
- #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_DROP UINT32_C(0x2)
- uint32_t enables;
- /* This bit must be '1' for the dst_id field to be configured. */
- #define HWRM_CFA_L2_FILTER_CFG_INPUT_ENABLES_DST_ID UINT32_C(0x1)
+ uint16_t pattern_buf_size;
/*
- * This bit must be '1' for the new_mirror_vnic_id field to be
- * configured.
+ * The size of the pattern buffer. Applies to bitmap WoL filter
+ * only.
*/
- #define HWRM_CFA_L2_FILTER_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
- UINT32_C(0x2)
- uint64_t l2_filter_id;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3[3];
+ uint8_t unused_4;
+ uint64_t pattern_mask_addr;
/*
- * This value identifies a set of CFA data structures used for
- * an L2 context.
+ * Physical address of the pattern mask. Applies to bitmap WoL
+ * filter only. # Value of 0 indicates an invalid pattern mask
+ * address. If this field is set to 0, then HWRM shall ignore
+ * pattern_mask_size. # If the HWRM client provides an invalid
+ * mask address for the pattern, then the HWRM is not required
+ * to provide mask when the response contains a bitmap WoL
+ * filter.
*/
- uint32_t dst_id;
+ uint16_t pattern_mask_size;
/*
- * If set, this value shall represent the Logical VNIC ID of the
- * destination VNIC for the RX path and network port id of the
- * destination port for the TX path.
+ * The size of the buffer for pattern mask. Applies to bitmap
+ * WoL filter only.
*/
- uint32_t new_mirror_vnic_id;
- /* New Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint16_t unused_5[3];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_cfa_l2_filter_cfg_output {
+/* Output (32 bytes) */
+struct hwrm_wol_filter_qcfg_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -9295,7 +25920,54 @@ struct hwrm_cfa_l2_filter_cfg_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
+ uint16_t next_handle;
+ /*
+ * This is the next handle that is used to access filters. # If
+ * this field is set to 0x0000, then no WoL filters are
+ * currently configured on this port and all other fields in the
+ * output shall be ignored by the HWRM client. # If this field
+ * is set to neither 0x0000 nor 0xFFFF, then the wol_filter_id
+ * is valid and the parameters provided in the response are
+ * based on the wol_type. # If this field is set to 0xFFFF, then
+ * there are no remaining configured WoL filters to be queried
+ * for the queried function after this response, wol_filter_id
+ * is valid and the parameters provided in the response are
+ * based on the wol_type.
+ */
+ uint8_t wol_filter_id;
+ /* This value identifies the filter returned in this response. */
+ uint8_t wol_type;
+ /*
+ * This value identifies the type of WoL filter returned in this
+ * response.
+ */
+ /* Magic Paket */
+ #define HWRM_WOL_FILTER_QCFG_OUTPUT_WOL_TYPE_MAGICPKT 0x0UL
+ /* Bitmap */
+ #define HWRM_WOL_FILTER_QCFG_OUTPUT_WOL_TYPE_BMP 0x1UL
+ /* Invalid */
+ #define HWRM_WOL_FILTER_QCFG_OUTPUT_WOL_TYPE_INVALID 0xffUL
uint32_t unused_0;
+ uint8_t mac_address[6];
+ /*
+ * The MAC address value used by the WoL filter. Applies to
+ * magic packet based WoL.
+ */
+ uint16_t pattern_offset;
+ /*
+ * The offset from the beginning of MAC header where pattern
+ * should be matched. Applies to bitmap WoL.
+ */
+ uint16_t pattern_size;
+ /*
+ * The actual size of the pattern that is being returned.
+ * Applies to bitmap WoL.
+ */
+ uint16_t pattern_mask_size;
+ /*
+ * The actual size of the pattern mask that is being returned.
+ * Applies to bitmap WoL.
+ */
uint8_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
@@ -9310,10 +25982,10 @@ struct hwrm_cfa_l2_filter_cfg_output {
*/
} __attribute__((packed));
-/* hwrm_cfa_l2_set_rx_mask */
-/* Description: This command will set rx mask of the function. */
-/* Input (56 bytes) */
-struct hwrm_cfa_l2_set_rx_mask_input {
+/* hwrm_wol_reason_qcfg */
+/* Description: Query WoL reason for the last system wake up. */
+/* Input (40 bytes) */
+struct hwrm_wol_reason_qcfg_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -9340,110 +26012,121 @@ struct hwrm_cfa_l2_set_rx_mask_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t vnic_id;
- /* VNIC ID */
- uint32_t mask;
- /* Reserved for future use. */
- #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_RESERVED UINT32_C(0x1)
+ uint16_t port_id;
+ /* Port ID of port for which this query is for. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2[3];
+ uint8_t unused_3;
+ uint64_t wol_pkt_buf_addr;
+ /* Physical address of the packet buffer for querying WoL packet. */
+ uint16_t wol_pkt_buf_size;
+ /* The size of the buffer for the WoL packet. */
+ uint16_t unused_4[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_wol_reason_qcfg_output {
+ uint16_t error_code;
/*
- * When this bit is '1', the function is requested to accept
- * multi-cast packets specified by the multicast addr table.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_MCAST UINT32_C(0x2)
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * When this bit is '1', the function is requested to accept all
- * multi-cast packets.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ALL_MCAST UINT32_C(0x4)
+ uint8_t wol_filter_id;
/*
- * When this bit is '1', the function is requested to accept
- * broadcast packets.
+ * This value identifies the filter that matched the last WoL
+ * packet. This id is only valid with valid WoL reason.
*/
- #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_BCAST UINT32_C(0x8)
+ uint8_t wol_reason;
/*
- * When this bit is '1', the function is requested to be put in
- * the promiscuous mode. The HWRM should accept any function to
- * set up promiscuous mode. The HWRM shall follow the semantics
- * below for the promiscuous mode support. # When partitioning
- * is not enabled on a port (i.e. single PF on the port), then
- * the PF shall be allowed to be in the promiscuous mode. When
- * the PF is in the promiscuous mode, then it shall receive all
- * host bound traffic on that port. # When partitioning is
- * enabled on a port (i.e. multiple PFs per port) and a PF on
- * that port is in the promiscuous mode, then the PF receives
- * all traffic within that partition as identified by a unique
- * identifier for the PF (e.g. S-Tag). If a unique outer VLAN
- * for the PF is specified, then the setting of promiscuous mode
- * on that PF shall result in the PF receiving all host bound
- * traffic with matching outer VLAN. # A VF shall can be set in
- * the promiscuous mode. In the promiscuous mode, the VF does
- * not receive any traffic unless a unique outer VLAN for the VF
- * is specified. If a unique outer VLAN for the VF is specified,
- * then the setting of promiscuous mode on that VF shall result
- * in the VF receiving all host bound traffic with the matching
- * outer VLAN. # The HWRM shall allow the setting of promiscuous
- * mode on a function independently from the promiscuous mode
- * settings on other functions.
+ * This value identifies the type of WoL reason returned in this
+ * response. When the wol_type is set to invalid, then there is
+ * no WoL event that happened during last system wake-up.
*/
- #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_PROMISCUOUS UINT32_C(0x10)
+ /* Magic Paket */
+ #define HWRM_WOL_REASON_QCFG_OUTPUT_WOL_REASON_MAGICPKT 0x0UL
+ /* Bitmap */
+ #define HWRM_WOL_REASON_QCFG_OUTPUT_WOL_REASON_BMP 0x1UL
+ /* Invalid */
+ #define HWRM_WOL_REASON_QCFG_OUTPUT_WOL_REASON_INVALID 0xffUL
+ uint8_t wol_pkt_len;
+ /* The value identifies the length of the WoL packet in bytes. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
/*
- * If this flag is set, the corresponding RX filters shall be
- * set up to cover multicast/broadcast filters for the outermost
- * Layer 2 destination MAC address field.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_OUTERMOST UINT32_C(0x20)
+} __attribute__((packed));
+
+/* hwrm_dbg_dump */
+/*
+ * Description: This command is used by to initiate the dump of debug
+ * information to a driver specified address.
+ */
+/* Input (40 bytes) */
+struct hwrm_dbg_dump_input {
+ uint16_t req_type;
/*
- * If this flag is set, the corresponding RX filters shall be
- * set up to cover multicast/broadcast filters for the VLAN-
- * tagged packets that match the TPID and VID fields of VLAN
- * tags in the VLAN tag table specified in this command.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_VLANONLY UINT32_C(0x40)
+ uint16_t cmpl_ring;
/*
- * If this flag is set, the corresponding RX filters shall be
- * set up to cover multicast/broadcast filters for non-VLAN
- * tagged packets and VLAN-tagged packets that match the TPID
- * and VID fields of VLAN tags in the VLAN tag table specified
- * in this command.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_VLAN_NONVLAN UINT32_C(0x80)
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * If this flag is set, the corresponding RX filters shall be
- * set up to cover multicast/broadcast filters for non-VLAN
- * tagged packets and VLAN-tagged packets matching any VLAN tag.
- * If this flag is set, then the HWRM shall ignore VLAN tags
- * specified in vlan_tag_tbl. If none of vlanonly, vlan_nonvlan,
- * and anyvlan_nonvlan flags is set, then the HWRM shall ignore
- * VLAN tags specified in vlan_tag_tbl. The HWRM client shall
- * set at most one flag out of vlanonly, vlan_nonvlan, and
- * anyvlan_nonvlan.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ANYVLAN_NONVLAN \
- UINT32_C(0x100)
- uint64_t mc_tbl_addr;
- /* This is the address for mcast address tbl. */
- uint32_t num_mc_entries;
+ uint64_t resp_addr;
/*
- * This value indicates how many entries in mc_tbl are valid.
- * Each entry is 6 bytes.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint32_t unused_0;
- uint64_t vlan_tag_tbl_addr;
+ uint32_t handle;
/*
- * This is the address for VLAN tag table. Each VLAN entry in
- * the table is 4 bytes of a VLAN tag including TPID, PCP, DEI,
- * and VID fields in network byte order.
+ * Handle used to dump debug data. handle = 0 indicates the
+ * beginning of the dump. handle != 0 indicates the request to
+ * dump the next part.
*/
- uint32_t num_vlan_tags;
+ uint32_t unused_0;
+ uint64_t host_dbg_dump_addr;
/*
- * This value indicates how many entries in vlan_tag_tbl are
- * valid. Each entry is 4 bytes.
+ * Address of the host buffer where the debug data is requested
+ * to be dumped.
*/
- uint32_t unused_1;
+ uint64_t host_dbg_dump_addr_len;
+ /* Length of host buffer used for transferring debug data. */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_cfa_l2_set_rx_mask_output {
+/* Output (24 bytes) */
+struct hwrm_dbg_dump_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -9459,6 +26142,15 @@ struct hwrm_cfa_l2_set_rx_mask_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
+ uint32_t nexthandle;
+ /*
+ * Handle used to indicate availability of additional debug
+ * data. nexthandle = 0 indicates that there is no more debug
+ * data available. nexthandle != 0 indicates the handle value
+ * that should be used to request the next part of debug data.
+ */
+ uint32_t dbg_data_len;
+ /* The number of bytes of debug data written to debug dump buffer. */
uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
@@ -9474,18 +26166,13 @@ struct hwrm_cfa_l2_set_rx_mask_output {
*/
} __attribute__((packed));
-/* hwrm_cfa_ntuple_filter_alloc */
+/* hwrm_dbg_coredump_list */
/*
- * Description: This is a ntuple filter that uses fields from L4/L3 header and
- * optionally fields from L2. The ntuple filters apply to receive traffic only.
- * All L2/L3/L4 header fields are specified in network byte order. These filters
- * can be used for Receive Flow Steering (RFS). # For ethertype value, only
- * 0x0800 (IPv4) and 0x86dd (IPv6) shall be supported for ntuple filters. # If a
- * field specified in this command is not enabled as a valid field, then that
- * field shall not be used in matching packet header fields against this filter.
+ * Description: This command is used to query the firmware component list for
+ * coredump.
*/
-/* Input (128 bytes) */
-struct hwrm_cfa_ntuple_filter_alloc_input {
+/* Input (32 bytes) */
+struct hwrm_dbg_coredump_list_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -9512,258 +26199,194 @@ struct hwrm_cfa_ntuple_filter_alloc_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t flags;
- /*
- * Setting of this flag indicates the applicability to the
- * loopback path.
- */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \
- UINT32_C(0x1)
- /*
- * Setting of this flag indicates drop action. If this flag is
- * not set, then it should be considered accept action.
- */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_DROP UINT32_C(0x2)
- /*
- * Setting of this flag indicates that a meter is expected to be
- * attached to this flow. This hint can be used when choosing
- * the action record format required for the flow.
- */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_METER UINT32_C(0x4)
- uint32_t enables;
- /* This bit must be '1' for the l2_filter_id field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_L2_FILTER_ID \
- UINT32_C(0x1)
- /* This bit must be '1' for the ethertype field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_ETHERTYPE \
- UINT32_C(0x2)
- /* This bit must be '1' for the tunnel_type field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
- UINT32_C(0x4)
- /* This bit must be '1' for the src_macaddr field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_MACADDR \
- UINT32_C(0x8)
- /* This bit must be '1' for the ipaddr_type field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_IPADDR_TYPE \
- UINT32_C(0x10)
- /* This bit must be '1' for the src_ipaddr field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR \
- UINT32_C(0x20)
- /*
- * This bit must be '1' for the src_ipaddr_mask field to be
- * configured.
- */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR_MASK \
- UINT32_C(0x40)
- /* This bit must be '1' for the dst_ipaddr field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR \
- UINT32_C(0x80)
- /*
- * This bit must be '1' for the dst_ipaddr_mask field to be
- * configured.
- */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR_MASK \
- UINT32_C(0x100)
- /* This bit must be '1' for the ip_protocol field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_IP_PROTOCOL \
- UINT32_C(0x200)
- /* This bit must be '1' for the src_port field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT \
- UINT32_C(0x400)
- /*
- * This bit must be '1' for the src_port_mask field to be
- * configured.
- */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT_MASK \
- UINT32_C(0x800)
- /* This bit must be '1' for the dst_port field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_PORT \
- UINT32_C(0x1000)
- /*
- * This bit must be '1' for the dst_port_mask field to be
- * configured.
- */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_PORT_MASK \
- UINT32_C(0x2000)
- /* This bit must be '1' for the pri_hint field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_PRI_HINT \
- UINT32_C(0x4000)
- /*
- * This bit must be '1' for the ntuple_filter_id field to be
- * configured.
- */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_NTUPLE_FILTER_ID \
- UINT32_C(0x8000)
- /* This bit must be '1' for the dst_id field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_ID \
- UINT32_C(0x10000)
- /*
- * This bit must be '1' for the mirror_vnic_id field to be
- * configured.
- */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
- UINT32_C(0x20000)
- /* This bit must be '1' for the dst_macaddr field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_MACADDR \
- UINT32_C(0x40000)
- uint64_t l2_filter_id;
+ uint64_t host_dest_addr;
/*
- * This value identifies a set of CFA data structures used for
- * an L2 context.
+ * host address where the data content will be written when the
+ * request is complete. This area must be 16B aligned.
*/
- uint8_t src_macaddr[6];
+ uint32_t host_buf_len;
+ /* Length of host buffer used for transferring debug data. */
+ uint16_t seq_no;
+ /* Sequence number of the request. Starts at 0. */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_dbg_coredump_list_output {
+ uint16_t error_code;
/*
- * This value indicates the source MAC address in the Ethernet
- * header.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- uint16_t ethertype;
- /* This value indicates the ethertype in the Ethernet header. */
- uint8_t ip_addr_type;
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * This value indicates the type of IP address. 4 - IPv4 6 -
- * IPv6 All others are invalid.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- /* invalid */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN \
- UINT32_C(0x0)
- /* IPv4 */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 \
- UINT32_C(0x4)
- /* IPv6 */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 \
- UINT32_C(0x6)
- uint8_t ip_protocol;
+ uint8_t flags;
/*
- * The value of protocol filed in IP header. Applies to UDP and
- * TCP traffic. 6 - UDP 17 - TCP
+ * Value of 1 means that there is more data available. Issue the
+ * request again with the next sequence number.
*/
- /* invalid */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN \
- UINT32_C(0x0)
- /* UDP */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP \
- UINT32_C(0x6)
- /* TCP */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_TCP \
- UINT32_C(0x11)
- uint16_t dst_id;
+ #define HWRM_DBG_COREDUMP_LIST_OUTPUT_FLAGS_MORE 0x1UL
+ uint8_t unused_0;
+ uint16_t total_segments;
+ /* Total number of segments to be returned. */
+ uint16_t data_len;
+ /* Actual length of data returned in bytes. */
+ uint8_t unused_1;
+ uint8_t valid;
/*
- * If set, this value shall represent the Logical VNIC ID of the
- * destination VNIC for the RX path and network port id of the
- * destination port for the TX path.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- uint16_t mirror_vnic_id;
- /* Logical VNIC ID of the VNIC where traffic is mirrored. */
- uint8_t tunnel_type;
+} __attribute__((packed));
+
+/* hwrm_dbg_coredump_initiate */
+/* Description: This command is issued to prepare for the RETRIEVE command. */
+/* Input (32 bytes) */
+struct hwrm_dbg_coredump_initiate_input {
+ uint16_t req_type;
/*
- * This value indicates the tunnel type for this filter. If this
- * field is not specified, then the filter shall apply to both
- * non-tunneled and tunneled packets. If this field conflicts
- * with the tunnel_type specified in the l2_filter_id, then the
- * HWRM shall return an error for this command.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- /* Non-tunnel */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
- UINT32_C(0x0)
- /* Virtual eXtensible Local Area Network (VXLAN) */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
- UINT32_C(0x1)
+ uint16_t cmpl_ring;
/*
- * Network Virtualization Generic Routing
- * Encapsulation (NVGRE)
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
- UINT32_C(0x2)
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * Generic Routing Encapsulation (GRE) inside
- * Ethernet payload
- */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
- UINT32_C(0x3)
- /* IP in IP */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
- UINT32_C(0x4)
- /* Generic Network Virtualization Encapsulation (Geneve) */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
- UINT32_C(0x5)
- /* Multi-Protocol Lable Switching (MPLS) */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
- UINT32_C(0x6)
- /* Stateless Transport Tunnel (STT) */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT UINT32_C(0x7)
- /*
- * Generic Routing Encapsulation (GRE) inside IP
- * datagram payload
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
- UINT32_C(0x8)
- /* Any tunneled traffic */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
- UINT32_C(0xff)
- uint8_t pri_hint;
+ uint64_t resp_addr;
/*
- * This hint is provided to help in placing the filter in the
- * filter table.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- /* No preference */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER \
- UINT32_C(0x0)
- /* Above the given filter */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE UINT32_C(0x1)
- /* Below the given filter */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_BELOW UINT32_C(0x2)
- /* As high as possible */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_HIGHEST \
- UINT32_C(0x3)
- /* As low as possible */
- #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_LOWEST UINT32_C(0x4)
- uint32_t src_ipaddr[4];
+ uint16_t component_id;
+ /* Component id of the returned component. */
+ uint16_t segment_id;
+ /* Segment id of the returned component. */
+ uint16_t instance;
+ /* Not used. */
+ uint16_t unused_0;
+ /* Not used. */
+ uint8_t seg_flags;
+ /* bit 0: live data bit 1: crashed data */
+ uint8_t unused_1[7];
+ /* Not used. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_dbg_coredump_initiate_output {
+ uint16_t error_code;
/*
- * The value of source IP address to be used in filtering. For
- * IPv4, first four bytes represent the IP address.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- uint32_t src_ipaddr_mask[4];
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * The value of source IP address mask to be used in filtering.
- * For IPv4, first four bytes represent the IP address mask.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- uint32_t dst_ipaddr[4];
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
/*
- * The value of destination IP address to be used in filtering.
- * For IPv4, first four bytes represent the IP address.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- uint32_t dst_ipaddr_mask[4];
+} __attribute__((packed));
+
+/* hwrm_dbg_coredump_retrieve */
+/* Description: This command is used to get the component data. */
+/* Input (56 bytes) */
+struct hwrm_dbg_coredump_retrieve_input {
+ uint16_t req_type;
/*
- * The value of destination IP address mask to be used in
- * filtering. For IPv4, first four bytes represent the IP
- * address mask.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- uint16_t src_port;
+ uint16_t cmpl_ring;
/*
- * The value of source port to be used in filtering. Applies to
- * UDP and TCP traffic.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- uint16_t src_port_mask;
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * The value of source port mask to be used in filtering.
- * Applies to UDP and TCP traffic.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint16_t dst_port;
+ uint64_t resp_addr;
/*
- * The value of destination port to be used in filtering.
- * Applies to UDP and TCP traffic.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint16_t dst_port_mask;
+ uint64_t host_dest_addr;
/*
- * The value of destination port mask to be used in filtering.
- * Applies to UDP and TCP traffic.
+ * host address where the data content will be written when the
+ * request is complete. This area must be 16B aligned.
*/
- uint64_t ntuple_filter_id_hint;
- /* This is the ID of the filter that goes along with the pri_hint. */
+ uint32_t host_buf_len;
+ /* Length of host buffer used for transferring debug data. */
+ uint32_t unused_0;
+ /* Not used. */
+ uint16_t component_id;
+ /* Component id of the returned component. */
+ uint16_t segment_id;
+ /* Segment id of the returned component. */
+ uint16_t instance;
+ /* Not used. */
+ uint16_t unused_1;
+ /* Not used. */
+ uint8_t seg_flags;
+ /* bit 0: live data bit 1: crashed data */
+ uint8_t unused_2;
+ uint16_t unused_3;
+ uint32_t unused_4;
+ /* Not used. */
+ uint32_t seq_no;
+ /* Sequence number is used per segment request. Starts at 0. */
+ uint32_t unused_5;
} __attribute__((packed));
-/* Output (24 bytes) */
-struct hwrm_cfa_ntuple_filter_alloc_output {
+/* Output (16 bytes) */
+struct hwrm_dbg_coredump_retrieve_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -9779,18 +26402,18 @@ struct hwrm_cfa_ntuple_filter_alloc_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint64_t ntuple_filter_id;
- /* This value is an opaque id into CFA data structures. */
- uint32_t flow_id;
+ uint8_t flags;
/*
- * This is the ID of the flow associated with this filter. This
- * value shall be used to match and associate the flow
- * identifier returned in completion records. A value of
- * 0xFFFFFFFF shall indicate no flow id.
+ * Value of 1 means that there is more data available. Issue the
+ * request again with the next sequence number.
*/
+ #define HWRM_DBG_COREDUMP_RETRIEVE_OUTPUT_FLAGS_MORE 0x1UL
uint8_t unused_0;
+ uint16_t data_len;
+ /* Actual length of data returned in bytes. */
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -9802,10 +26425,14 @@ struct hwrm_cfa_ntuple_filter_alloc_output {
*/
} __attribute__((packed));
-/* hwrm_cfa_ntuple_filter_free */
-/* Description: Free an ntuple filter */
-/* Input (24 bytes) */
-struct hwrm_cfa_ntuple_filter_free_input {
+/* hwrm_nvm_raw_write_blk */
+/*
+ * Note: Write an unmanaged block of data at any physical offset within the
+ * NVRAM. Used for initial provisioning/manufacturing purposes only. Implemented
+ * in the ChiMP boot-strap firmware (fwutil.bin) only.
+ */
+/* Input (32 bytes) */
+struct hwrm_nvm_raw_write_blk_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -9832,12 +26459,22 @@ struct hwrm_cfa_ntuple_filter_free_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint64_t ntuple_filter_id;
- /* This value is an opaque id into CFA data structures. */
+ uint64_t host_src_addr;
+ /*
+ * 64-bit Host Source Address. This is the loation of the source
+ * data to be written.
+ */
+ uint32_t dest_addr;
+ /*
+ * 32-bit Destination Address. This is the NVRAM byte-offset
+ * where the source data will be written to.
+ */
+ uint32_t len;
+ /* Length of data to be written, in bytes. */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_cfa_ntuple_filter_free_output {
+/* Output (16 bytes) */
+struct hwrm_nvm_raw_write_blk_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -9868,13 +26505,13 @@ struct hwrm_cfa_ntuple_filter_free_output {
*/
} __attribute__((packed));
-/* hwrm_cfa_ntuple_filter_cfg */
+/* hwrm_nvm_read */
/*
- * Description: Configure an ntuple filter with a new destination VNIC and/or
- * meter.
+ * Note: Read the contents of an NVRAM item as referenced (indexed) by an
+ * existing directory entry.
*/
-/* Input (48 bytes) */
-struct hwrm_cfa_ntuple_filter_cfg_input {
+/* Input (40 bytes) */
+struct hwrm_nvm_read_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -9901,50 +26538,24 @@ struct hwrm_cfa_ntuple_filter_cfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t enables;
- /* This bit must be '1' for the new_dst_id field to be configured. */
- #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_DST_ID \
- UINT32_C(0x1)
- /*
- * This bit must be '1' for the new_mirror_vnic_id field to be
- * configured.
- */
- #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
- UINT32_C(0x2)
- /*
- * This bit must be '1' for the new_meter_instance_id field to
- * be configured.
- */
- #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_METER_INSTANCE_ID \
- UINT32_C(0x4)
- uint32_t unused_0;
- uint64_t ntuple_filter_id;
- /* This value is an opaque id into CFA data structures. */
- uint32_t new_dst_id;
- /*
- * If set, this value shall represent the new Logical VNIC ID of
- * the destination VNIC for the RX path and new network port id
- * of the destination port for the TX path.
- */
- uint32_t new_mirror_vnic_id;
- /* New Logical VNIC ID of the VNIC where traffic is mirrored. */
- uint16_t new_meter_instance_id;
- /*
- * New meter to attach to the flow. Specifying the invalid
- * instance ID is used to remove any existing meter from the
- * flow.
- */
+ uint64_t host_dest_addr;
/*
- * A value of 0xfff is considered invalid and
- * implies the instance is not configured.
+ * 64-bit Host Destination Address. This is the host address
+ * where the data will be written to.
*/
- #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID \
- UINT32_C(0xffff)
- uint16_t unused_1[3];
+ uint16_t dir_idx;
+ /* The 0-based index of the directory entry. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t offset;
+ /* The NVRAM byte-offset to read from. */
+ uint32_t len;
+ /* The length of the data to be read, in bytes. */
+ uint32_t unused_2;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_cfa_ntuple_filter_cfg_output {
+/* Output (16 bytes) */
+struct hwrm_nvm_read_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -9975,19 +26586,10 @@ struct hwrm_cfa_ntuple_filter_cfg_output {
*/
} __attribute__((packed));
-/* hwrm_cfa_em_flow_alloc */
-/*
- * Description: This is a generic Exact Match (EM) flow that uses fields from
- * L4/L3/L2 headers. The EM flows apply to transmit and receive traffic. All
- * L2/L3/L4 header fields are specified in network byte order. For each EM flow,
- * there is an associated set of actions specified. For tunneled packets, all
- * L2/L3/L4 fields specified are fields of inner headers unless otherwise
- * specified. # If a field specified in this command is not enabled as a valid
- * field, then that field shall not be used in matching packet header fields
- * against this EM flow entry.
- */
-/* Input (112 bytes) */
-struct hwrm_cfa_em_flow_alloc_input {
+/* hwrm_nvm_raw_dump */
+/* Note: Dump a raw block of data from NVRAM. */
+/* Input (32 bytes) */
+struct hwrm_nvm_raw_dump_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -10014,237 +26616,99 @@ struct hwrm_cfa_em_flow_alloc_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t flags;
- /*
- * Enumeration denoting the RX, TX type of the resource. This
- * enumeration is used for resources that are similar for both
- * TX and RX paths of the chip.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH UINT32_C(0x1)
- /* tx path */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_TX \
- (UINT32_C(0x0) << 0)
- /* rx path */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_RX \
- (UINT32_C(0x1) << 0)
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_LAST \
- CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_RX
- /*
- * Setting of this flag indicates enabling of a byte counter for
- * a given flow.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_BYTE_CTR UINT32_C(0x2)
- /*
- * Setting of this flag indicates enabling of a packet counter
- * for a given flow.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PKT_CTR UINT32_C(0x4)
- /*
- * Setting of this flag indicates de-capsulation action for the
- * given flow.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_DECAP UINT32_C(0x8)
- /*
- * Setting of this flag indicates encapsulation action for the
- * given flow.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_ENCAP UINT32_C(0x10)
- /*
- * Setting of this flag indicates drop action. If this flag is
- * not set, then it should be considered accept action.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_DROP UINT32_C(0x20)
- /*
- * Setting of this flag indicates that a meter is expected to be
- * attached to this flow. This hint can be used when choosing
- * the action record format required for the flow.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_METER UINT32_C(0x40)
- uint32_t enables;
- /* This bit must be '1' for the l2_filter_id field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_L2_FILTER_ID UINT32_C(0x1)
- /* This bit must be '1' for the tunnel_type field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_TUNNEL_TYPE UINT32_C(0x2)
- /* This bit must be '1' for the tunnel_id field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_TUNNEL_ID UINT32_C(0x4)
- /* This bit must be '1' for the src_macaddr field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_MACADDR UINT32_C(0x8)
- /* This bit must be '1' for the dst_macaddr field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_MACADDR UINT32_C(0x10)
- /* This bit must be '1' for the ovlan_vid field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_OVLAN_VID UINT32_C(0x20)
- /* This bit must be '1' for the ivlan_vid field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IVLAN_VID UINT32_C(0x40)
- /* This bit must be '1' for the ethertype field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_ETHERTYPE UINT32_C(0x80)
- /* This bit must be '1' for the src_ipaddr field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_IPADDR UINT32_C(0x100)
- /* This bit must be '1' for the dst_ipaddr field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_IPADDR UINT32_C(0x200)
- /* This bit must be '1' for the ipaddr_type field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IPADDR_TYPE UINT32_C(0x400)
- /* This bit must be '1' for the ip_protocol field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IP_PROTOCOL UINT32_C(0x800)
- /* This bit must be '1' for the src_port field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_PORT UINT32_C(0x1000)
- /* This bit must be '1' for the dst_port field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_PORT UINT32_C(0x2000)
- /* This bit must be '1' for the dst_id field to be configured. */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_ID UINT32_C(0x4000)
- /*
- * This bit must be '1' for the mirror_vnic_id field to be
- * configured.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
- UINT32_C(0x8000)
- /*
- * This bit must be '1' for the encap_record_id field to be
- * configured.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_ENCAP_RECORD_ID \
- UINT32_C(0x10000)
- /*
- * This bit must be '1' for the meter_instance_id field to be
- * configured.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_METER_INSTANCE_ID \
- UINT32_C(0x20000)
- uint64_t l2_filter_id;
- /*
- * This value identifies a set of CFA data structures used for
- * an L2 context.
- */
- uint8_t tunnel_type;
- /* Tunnel Type. */
- /* Non-tunnel */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
- UINT32_C(0x0)
- /* Virtual eXtensible Local Area Network (VXLAN) */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN UINT32_C(0x1)
- /*
- * Network Virtualization Generic Routing
- * Encapsulation (NVGRE)
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NVGRE UINT32_C(0x2)
- /*
- * Generic Routing Encapsulation (GRE) inside
- * Ethernet payload
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_L2GRE UINT32_C(0x3)
- /* IP in IP */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPIP UINT32_C(0x4)
- /* Generic Network Virtualization Encapsulation (Geneve) */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_GENEVE UINT32_C(0x5)
- /* Multi-Protocol Lable Switching (MPLS) */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_MPLS UINT32_C(0x6)
- /* Stateless Transport Tunnel (STT) */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_STT UINT32_C(0x7)
- /*
- * Generic Routing Encapsulation (GRE) inside IP
- * datagram payload
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPGRE UINT32_C(0x8)
- /* Any tunneled traffic */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
- UINT32_C(0xff)
- uint8_t unused_0;
- uint16_t unused_1;
- uint32_t tunnel_id;
- /*
- * Tunnel identifier. Virtual Network Identifier (VNI). Only
- * valid with tunnel_types VXLAN, NVGRE, and Geneve. Only lower
- * 24-bits of VNI field are used in setting up the filter.
- */
- uint8_t src_macaddr[6];
- /*
- * This value indicates the source MAC address in the Ethernet
- * header.
- */
- uint16_t meter_instance_id;
- /* The meter instance to attach to the flow. */
- /*
- * A value of 0xfff is considered invalid and
- * implies the instance is not configured.
- */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_METER_INSTANCE_ID_INVALID \
- UINT32_C(0xffff)
- uint8_t dst_macaddr[6];
- /*
- * This value indicates the destination MAC address in the
- * Ethernet header.
- */
- uint16_t ovlan_vid;
- /*
- * This value indicates the VLAN ID of the outer VLAN tag in the
- * Ethernet header.
- */
- uint16_t ivlan_vid;
+ uint64_t host_dest_addr;
/*
- * This value indicates the VLAN ID of the inner VLAN tag in the
- * Ethernet header.
+ * 64-bit Host Destination Address. This is the host address
+ * where the data will be written to.
*/
- uint16_t ethertype;
- /* This value indicates the ethertype in the Ethernet header. */
- uint8_t ip_addr_type;
+ uint32_t offset;
+ /* 32-bit NVRAM byte-offset to read from. */
+ uint32_t len;
+ /* Total length of NVRAM contents to be read, in bytes. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_nvm_raw_dump_output {
+ uint16_t error_code;
/*
- * This value indicates the type of IP address. 4 - IPv4 6 -
- * IPv6 All others are invalid.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- /* invalid */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN UINT32_C(0x0)
- /* IPv4 */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 UINT32_C(0x4)
- /* IPv6 */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 UINT32_C(0x6)
- uint8_t ip_protocol;
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * The value of protocol filed in IP header. Applies to UDP and
- * TCP traffic. 6 - UDP 17 - TCP
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- /* invalid */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN UINT32_C(0x0)
- /* UDP */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UDP UINT32_C(0x6)
- /* TCP */
- #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_TCP UINT32_C(0x11)
+ uint32_t unused_0;
+ uint8_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
- uint32_t src_ipaddr[4];
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_nvm_get_dir_entries */
+/*
+ * Description: Read the NVRAM directory. Each directory entry is at least 24
+ * bytes in length and contains the: - 16-bit directory entry type
+ * (BNX_DIR_TYPE_* value) - 16-bit ordinal (instance of this directory entry
+ * type) - 16-bit extension flags (identifies inactive entries and entries for
+ * firmware update) - 16-bit attribute flags (identifies entries with a
+ * purposely invalid chksum value) - 32-bit byte-offset into NVRAM where this
+ * item data is located - 32-bit length of allocated NVRAM for item, in bytes
+ * (multiple of block size) - 32-bit length of data (excluding padding), in
+ * bytes (may be 0) - 32-bit data checksum (CRC-32) See the
+ * bnxnvm_directory_entry_t definition in the file bnxnvm_defs.h.
+ */
+/* Input (24 bytes) */
+struct hwrm_nvm_get_dir_entries_input {
+ uint16_t req_type;
/*
- * The value of source IP address to be used in filtering. For
- * IPv4, first four bytes represent the IP address.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
- uint32_t dst_ipaddr[4];
+ uint16_t cmpl_ring;
/*
- * big_endian = True The value of destination IP address to be
- * used in filtering. For IPv4, first four bytes represent the
- * IP address.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
- uint16_t src_port;
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
/*
- * The value of source port to be used in filtering. Applies to
- * UDP and TCP traffic.
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
- uint16_t dst_port;
+ uint64_t resp_addr;
/*
- * The value of destination port to be used in filtering.
- * Applies to UDP and TCP traffic.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint16_t dst_id;
+ uint64_t host_dest_addr;
/*
- * If set, this value shall represent the Logical VNIC ID of the
- * destination VNIC for the RX path and network port id of the
- * destination port for the TX path.
+ * 64-bit Host Destination Address. This is the host address
+ * where the directory will be written.
*/
- uint16_t mirror_vnic_id;
- /* Logical VNIC ID of the VNIC where traffic is mirrored. */
- uint32_t encap_record_id;
- /* Logical ID of the encapsulation record. */
- uint32_t unused_4;
} __attribute__((packed));
-/* Output (24 bytes) */
-struct hwrm_cfa_em_flow_alloc_output {
+/* Output (16 bytes) */
+struct hwrm_nvm_get_dir_entries_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -10260,18 +26724,10 @@ struct hwrm_cfa_em_flow_alloc_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint64_t em_filter_id;
- /* This value is an opaque id into CFA data structures. */
- uint32_t flow_id;
- /*
- * This is the ID of the flow associated with this filter. This
- * value shall be used to match and associate the flow
- * identifier returned in completion records. A value of
- * 0xFFFFFFFF shall indicate no flow id.
- */
- uint8_t unused_0;
+ uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -10283,10 +26739,10 @@ struct hwrm_cfa_em_flow_alloc_output {
*/
} __attribute__((packed));
-/* hwrm_cfa_em_flow_free */
-/* Description: Free an EM flow table entry */
-/* Input (24 bytes) */
-struct hwrm_cfa_em_flow_free_input {
+/* hwrm_nvm_get_dir_info */
+/* Note: Get Directory Header info. */
+/* Input (16 bytes) */
+struct hwrm_nvm_get_dir_info_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -10313,12 +26769,10 @@ struct hwrm_cfa_em_flow_free_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint64_t em_filter_id;
- /* This value is an opaque id into CFA data structures. */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_cfa_em_flow_free_output {
+/* Output (24 bytes) */
+struct hwrm_nvm_get_dir_info_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -10334,6 +26788,10 @@ struct hwrm_cfa_em_flow_free_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
+ uint32_t entries;
+ /* Number of directory entries in the directory. */
+ uint32_t entry_length;
+ /* Size of each directory entry, in bytes. */
uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
@@ -10349,12 +26807,13 @@ struct hwrm_cfa_em_flow_free_output {
*/
} __attribute__((packed));
-/* hwrm_cfa_em_flow_cfg */
+/* hwrm_nvm_write */
/*
- * Description: Configure an EM flow with a new destination VNIC and/or meter.
+ * Note: Write to the allocated NVRAM of an item referenced by an existing
+ * directory entry.
*/
-/* Input (48 bytes) */
-struct hwrm_cfa_em_flow_cfg_input {
+/* Input (48 bytes) */
+struct hwrm_nvm_write_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -10381,49 +26840,167 @@ struct hwrm_cfa_em_flow_cfg_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t enables;
- /* This bit must be '1' for the new_dst_id field to be configured. */
- #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_DST_ID UINT32_C(0x1)
+ uint64_t host_src_addr;
+ /* 64-bit Host Source Address. This is where the source data is. */
+ uint16_t dir_type;
/*
- * This bit must be '1' for the new_mirror_vnic_id field to be
- * configured.
+ * The Directory Entry Type (valid values are defined in the
+ * bnxnvm_directory_type enum defined in the file
+ * bnxnvm_defs.h).
*/
- #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
- UINT32_C(0x2)
+ uint16_t dir_ordinal;
/*
- * This bit must be '1' for the new_meter_instance_id field to
- * be configured.
+ * Directory ordinal. The 0-based instance of the combined
+ * Directory Entry Type and Extension.
+ */
+ uint16_t dir_ext;
+ /*
+ * The Directory Entry Extension flags (see BNX_DIR_EXT_* in the
+ * file bnxnvm_defs.h).
+ */
+ uint16_t dir_attr;
+ /*
+ * Directory Entry Attribute flags (see BNX_DIR_ATTR_* in the
+ * file bnxnvm_defs.h).
+ */
+ uint32_t dir_data_length;
+ /*
+ * Length of data to write, in bytes. May be less than or equal
+ * to the allocated size for the directory entry. The data
+ * length stored in the directory entry will be updated to
+ * reflect this value once the write is complete.
+ */
+ uint16_t option;
+ /* Option. */
+ uint16_t flags;
+ /*
+ * When this bit is '1', the original active image will not be
+ * removed. TBD: what purpose is this?
+ */
+ #define HWRM_NVM_WRITE_INPUT_FLAGS_KEEP_ORIG_ACTIVE_IMG 0x1UL
+ uint32_t dir_item_length;
+ /*
+ * The requested length of the allocated NVM for the item, in
+ * bytes. This value may be greater than or equal to the
+ * specified data length (dir_data_length). If this value is
+ * less than the specified data length, it will be ignored. The
+ * response will contain the actual allocated item length, which
+ * may be greater than the requested item length. The purpose
+ * for allocating more than the required number of bytes for an
+ * item's data is to pre-allocate extra storage (padding) to
+ * accomodate the potential future growth of an item (e.g.
+ * upgraded firmware with a size increase, log growth, expanded
+ * configuration data).
*/
- #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_METER_INSTANCE_ID \
- UINT32_C(0x4)
uint32_t unused_0;
- uint64_t em_filter_id;
- /* This value is an opaque id into CFA data structures. */
- uint32_t new_dst_id;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_nvm_write_output {
+ uint16_t error_code;
/*
- * If set, this value shall represent the new Logical VNIC ID of
- * the destination VNIC for the RX path and network port id of
- * the destination port for the TX path.
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
- uint32_t new_mirror_vnic_id;
- /* New Logical VNIC ID of the VNIC where traffic is mirrored. */
- uint16_t new_meter_instance_id;
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
/*
- * New meter to attach to the flow. Specifying the invalid
- * instance ID is used to remove any existing meter from the
- * flow.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
+ uint32_t dir_item_length;
/*
- * A value of 0xfff is considered invalid and
- * implies the instance is not configured.
+ * Length of the allocated NVM for the item, in bytes. The value
+ * may be greater than or equal to the specified data length or
+ * the requested item length. The actual item length used when
+ * creating a new directory entry will be a multiple of an NVM
+ * block size.
+ */
+ uint16_t dir_idx;
+ /* The directory index of the created or modified item. */
+ uint8_t unused_0;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
- #define HWRM_CFA_EM_FLOW_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID \
- UINT32_C(0xffff)
- uint16_t unused_1[3];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_cfa_em_flow_cfg_output {
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_nvm_write_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_NVM_WRITE_CMD_ERR_CODE_UNKNOWN 0x0UL
+ /* Unable to complete operation due to fragmentation */
+ #define HWRM_NVM_WRITE_CMD_ERR_CODE_FRAG_ERR 0x1UL
+ /* nvm is completely full. */
+ #define HWRM_NVM_WRITE_CMD_ERR_CODE_NO_SPACE 0x2UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* hwrm_nvm_modify */
+/*
+ * Note: Modify the contents of an NVRAM item as referenced (indexed) by an
+ * existing directory entry.
+ */
+/* Input (40 bytes) */
+struct hwrm_nvm_modify_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint64_t host_src_addr;
+ /* 64-bit Host Source Address. This is where the modified data is. */
+ uint16_t dir_idx;
+ /* 16-bit directory entry index. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t offset;
+ /* 32-bit NVRAM byte-offset to modify content from. */
+ uint32_t len;
+ /*
+ * Length of data to be modified, in bytes. The length shall be
+ * non-zero.
+ */
+ uint32_t unused_2;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_nvm_modify_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -10454,61 +27031,72 @@ struct hwrm_cfa_em_flow_cfg_output {
*/
} __attribute__((packed));
-
-/* hwrm_cfa_vlan_antispoof_cfg */
-/* Description: Configures vlan anti-spoof filters for VF. */
+/* hwrm_nvm_find_dir_entry */
+/*
+ * Note: Search a directory entry in the directory by either directory entry
+ * index or directory entry parameters.
+ */
/* Input (32 bytes) */
-struct hwrm_cfa_vlan_antispoof_cfg_input {
+struct hwrm_nvm_find_dir_entry_input {
uint16_t req_type;
/*
- * This value indicates what type of request this is. The format for the
- * rest of the command is determined by this field.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
uint16_t cmpl_ring;
/*
- * This value indicates the what completion ring the request will be
- * optionally completed on. If the value is -1, then no CR completion
- * will be generated. Any other value must be a valid CR ring_id value
- * for this function.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
uint16_t seq_id;
/* This value indicates the command sequence number. */
uint16_t target_id;
/*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
- * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
uint64_t resp_addr;
/*
- * This is the host address where the response will be written when the
- * request is complete. This area must be 16B aligned and must be
- * cleared to zero before the request is made.
- */
- uint16_t fid;
- /*
- * Function ID of the function that is being configured. Only valid for
- * a VF FID configured by the PF.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint8_t unused_0;
- uint8_t unused_1;
- uint32_t num_vlan_entries;
- /* Number of VLAN entries in the vlan_tag_mask_tbl. */
- uint64_t vlan_tag_mask_tbl_addr;
+ uint32_t enables;
/*
- * The vlan_tag_mask_tbl_addr is the DMA address of the VLAN antispoof
- * table. Each table entry contains the 16-bit TPID (0x8100 or 0x88a8
- * only), 16-bit VLAN ID, and a 16-bit mask, all in network order to
- * match hwrm_cfa_l2_set_rx_mask. For an individual VLAN entry, the mask
- * value should be 0xfff for the 12-bit VLAN ID.
+ * This bit must be '1' for the dir_idx_valid field to be
+ * configured.
*/
-};
+ #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_ENABLES_DIR_IDX_VALID 0x1UL
+ uint16_t dir_idx;
+ /* Directory Entry Index */
+ uint16_t dir_type;
+ /* Directory Entry (Image) Type */
+ uint16_t dir_ordinal;
+ /* Directory ordinal. The instance of this Directory Type */
+ uint16_t dir_ext;
+ /* The Directory Entry Extension flags. */
+ uint8_t opt_ordinal;
+ /* This value indicates the search option using dir_ordinal. */
+ #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_MASK 0x3UL
+ #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_SFT 0
+ /* Equal to specified ordinal value. */
+ #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_EQ 0x0UL
+ /* Greater than or equal to specified ordinal value */
+ #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_GE 0x1UL
+ /* Greater than specified ordinal value */
+ #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_GT 0x2UL
+ uint8_t unused_1[3];
+} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_cfa_vlan_antispoof_cfg_output {
+/* Output (32 bytes) */
+struct hwrm_nvm_find_dir_entry_output {
uint16_t error_code;
/*
- * Pass/Fail or error type Note: receiver to verify the in parameters,
- * and fail the call with an error when appropriate
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
uint16_t req_type;
/* This field returns the type of original request. */
@@ -10516,31 +27104,45 @@ struct hwrm_cfa_vlan_antispoof_cfg_output {
/* This field provides original sequence number of the command. */
uint16_t resp_len;
/*
- * This field is the length of the response in bytes. The last byte of
- * the response is a valid flag that will read as '1' when the command
- * has been completely written to memory.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t dir_item_length;
+ /* Allocated NVRAM for this directory entry, in bytes. */
+ uint32_t dir_data_length;
+ /* Size of the stored data for this directory entry, in bytes. */
+ uint32_t fw_ver;
+ /*
+ * Firmware version. Only valid if the directory entry is for
+ * embedded firmware stored in APE_BIN Format.
*/
+ uint16_t dir_ordinal;
+ /* Directory ordinal. */
+ uint16_t dir_idx;
+ /* Directory Entry Index */
uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
uint8_t valid;
/*
- * This field is used in Output records to indicate that the output is
- * completely written to RAM. This field should be read as '1' to
- * indicate that the output has been completely written. When writing a
- * command completion or response to an internal processor, the order of
- * writes has to be such that this field is written last.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
*/
-};
+} __attribute__((packed));
-/* hwrm_tunnel_dst_port_query */
-/*
- * Description: This function is called by a driver to query tunnel type
- * specific destination port configuration.
+/* hwrm_nvm_erase_dir_entry */
+/*
+ * Note: Remove a directory entry specified by the directory entry index from
+ * the directory.
*/
-/* Input (24 bytes) */
-struct hwrm_tunnel_dst_port_query_input {
+/* Input (24 bytes) */
+struct hwrm_nvm_erase_dir_entry_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -10567,19 +27169,13 @@ struct hwrm_tunnel_dst_port_query_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint8_t tunnel_type;
- /* Tunnel Type. */
- /* Virtual eXtensible Local Area Network (VXLAN) */
- #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_VXLAN \
- UINT32_C(0x1)
- /* Generic Network Virtualization Encapsulation (Geneve) */
- #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_GENEVE \
- UINT32_C(0x5)
- uint8_t unused_0[7];
+ uint16_t dir_idx;
+ /* Directory Entry Index */
+ uint16_t unused_0[3];
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_tunnel_dst_port_query_output {
+/* Output (16 bytes) */
+struct hwrm_nvm_erase_dir_entry_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -10595,24 +27191,10 @@ struct hwrm_tunnel_dst_port_query_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint16_t tunnel_dst_port_id;
- /*
- * This field represents the identifier of L4 destination port
- * used for the given tunnel type. This field is valid for
- * specific tunnel types that use layer 4 (e.g. UDP) transports
- * for tunneling.
- */
- uint16_t tunnel_dst_port_val;
- /*
- * This field represents the value of L4 destination port
- * identified by tunnel_dst_port_id. This field is valid for
- * specific tunnel types that use layer 4 (e.g. UDP) transports
- * for tunneling. This field is in network byte order. A value
- * of 0 means that the destination port is not configured.
- */
- uint8_t unused_0;
+ uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -10624,24 +27206,13 @@ struct hwrm_tunnel_dst_port_query_output {
*/
} __attribute__((packed));
-/* hwrm_tunnel_dst_port_alloc */
+/* hwrm_nvm_get_dev_info */
/*
- * Description: This function is called by a driver to allocate l4 destination
- * port for a specific tunnel type. The destination port value is provided in
- * the input. If the HWRM supports only one global destination port for a tunnel
- * type, then the HWRM shall keep track of its usage as described below. # The
- * first caller that allocates a destination port shall always succeed and the
- * HWRM shall save the destination port configuration for that tunnel type and
- * increment the usage count to 1. # Subsequent callers allocating the same
- * destination port for that tunnel type shall succeed and the HWRM shall
- * increment the usage count for that port for each subsequent caller that
- * succeeds. # Any subsequent caller trying to allocate a different destination
- * port for that tunnel type shall fail until the usage count for the original
- * destination port goes to zero. # A caller that frees a port will cause the
- * usage count for that port to decrement.
+ * Note: Get device info. Return Manufacturer_ID, Device_ID, block_size,
+ * nvram_size, reserved_size and available_size.
*/
-/* Input (24 bytes) */
-struct hwrm_tunnel_dst_port_alloc_input {
+/* Input (16 bytes) */
+struct hwrm_nvm_get_dev_info_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -10668,27 +27239,10 @@ struct hwrm_tunnel_dst_port_alloc_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint8_t tunnel_type;
- /* Tunnel Type. */
- /* Virtual eXtensible Local Area Network (VXLAN) */
- #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_VXLAN UINT32_C(0x1)
- /* Generic Network Virtualization Encapsulation (Geneve) */
- #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
- UINT32_C(0x5)
- uint8_t unused_0;
- uint16_t tunnel_dst_port_val;
- /*
- * This field represents the value of L4 destination port used
- * for the given tunnel type. This field is valid for specific
- * tunnel types that use layer 4 (e.g. UDP) transports for
- * tunneling. This field is in network byte order. A value of 0
- * shall fail the command.
- */
- uint32_t unused_1;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_tunnel_dst_port_alloc_output {
+/* Output (32 bytes) */
+struct hwrm_nvm_get_dev_info_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -10704,17 +27258,23 @@ struct hwrm_tunnel_dst_port_alloc_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint16_t tunnel_dst_port_id;
+ uint16_t manufacturer_id;
+ /* Manufacturer ID. */
+ uint16_t device_id;
+ /* Device ID. */
+ uint32_t sector_size;
+ /* Sector size of the NVRAM device. */
+ uint32_t nvram_size;
+ /* Total size, in bytes of the NVRAM device. */
+ uint32_t reserved_size;
+ uint32_t available_size;
/*
- * Identifier of a tunnel L4 destination port value. Only
- * applies to tunnel types that has l4 destination port
- * parameters.
+ * Available size that can be used, in bytes. Available size is
+ * the NVRAM size take away the used size and reserved size.
*/
uint8_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
- uint8_t unused_3;
- uint8_t unused_4;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -10726,13 +27286,10 @@ struct hwrm_tunnel_dst_port_alloc_output {
*/
} __attribute__((packed));
-/* hwrm_tunnel_dst_port_free */
-/*
- * Description: This function is called by a driver to free l4 destination port
- * for a specific tunnel type.
- */
-/* Input (24 bytes) */
-struct hwrm_tunnel_dst_port_free_input {
+/* hwrm_nvm_mod_dir_entry */
+/* Note: Modify a directory entry parameters in the directory. */
+/* Input (32 bytes) */
+struct hwrm_nvm_mod_dir_entry_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -10759,24 +27316,32 @@ struct hwrm_tunnel_dst_port_free_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint8_t tunnel_type;
- /* Tunnel Type. */
- /* Virtual eXtensible Local Area Network (VXLAN) */
- #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_VXLAN UINT32_C(0x1)
- /* Generic Network Virtualization Encapsulation (Geneve) */
- #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_GENEVE UINT32_C(0x5)
- uint8_t unused_0;
- uint16_t tunnel_dst_port_id;
+ uint32_t enables;
+ /* This bit must be '1' for the checksum field to be configured. */
+ #define HWRM_NVM_MOD_DIR_ENTRY_INPUT_ENABLES_CHECKSUM 0x1UL
+ uint16_t dir_idx;
+ /* Directory Entry Index */
+ uint16_t dir_ordinal;
+ /* Directory ordinal. The (0-based) instance of this Directory Type. */
+ uint16_t dir_ext;
/*
- * Identifier of a tunnel L4 destination port value. Only
- * applies to tunnel types that has l4 destination port
- * parameters.
+ * The Directory Entry Extension flags (see BNX_DIR_EXT_* for
+ * extension flag definitions).
+ */
+ uint16_t dir_attr;
+ /*
+ * Directory Entry Attribute flags (see BNX_DIR_ATTR_* for
+ * attribute flag definitions).
+ */
+ uint32_t checksum;
+ /*
+ * If valid, then this field updates the checksum value of the
+ * content in the directory entry.
*/
- uint32_t unused_1;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_tunnel_dst_port_free_output {
+/* Output (16 bytes) */
+struct hwrm_nvm_mod_dir_entry_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -10807,13 +27372,24 @@ struct hwrm_tunnel_dst_port_free_output {
*/
} __attribute__((packed));
-/* hwrm_stat_ctx_alloc */
+/* hwrm_nvm_verify_update */
/*
- * Description: This command allocates and does basic preparation for a stat
- * context.
+ * Description: Verify updated content of a directory entry. Before this
+ * verification, there should be two valid directory entries of the given
+ * directory type (one with "UPDATE" directory extension flag and the current
+ * one "ACTIVE"). Below are steps the HWRM performs for executing this command:
+ * # The HWRM finds the directory entry with "UDPATE" extension flag based on
+ * input parameters. The new directory entry should already have updated
+ * contents. # The HWRM performs signature verification of the updated content.
+ * # If the signature verification is successful, the two directory entries are
+ * switched (the verified updated entry is made active and the current "ACTIVE"
+ * entry is marked with "UPDATE" extension flag). Implementation notes: # The
+ * HWRM shall allow this command to be requested against any dir_type value (and
+ * not limit it to a subset). # In the case of an updated HWRM firmware, the new
+ * firmware version shall not automatically take effect (i.e. be executed).
*/
-/* Input (32 bytes) */
-struct hwrm_stat_ctx_alloc_input {
+/* Input (24 bytes) */
+struct hwrm_nvm_verify_update_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -10840,35 +27416,27 @@ struct hwrm_stat_ctx_alloc_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint64_t stats_dma_addr;
- /* This is the address for statistic block. */
- uint32_t update_period_ms;
- /*
- * The statistic block update period in ms. e.g. 250ms, 500ms,
- * 750ms, 1000ms. If update_period_ms is 0, then the stats
- * update shall be never done and the DMA address shall not be
- * used. In this case, the stat block can only be read by
- * hwrm_stat_ctx_query command.
- */
- uint8_t stat_ctx_flags;
+ uint16_t dir_type;
+ /* Directory Entry Type, to be verified. */
+ uint16_t dir_ordinal;
/*
- * This field is used to specify statistics context specific
- * configuration flags.
+ * Directory ordinal. The instance of the Directory Type to be
+ * verified.
*/
+ uint16_t dir_ext;
/*
- * When this bit is set to '1', the statistics context shall be
- * allocated for RoCE traffic only. In this case, traffic other
- * than offloaded RoCE traffic shall not be included in this
- * statistic context. When this bit is set to '0', the
- * statistics context shall be used for the network traffic
- * other than offloaded RoCE traffic.
+ * The Directory Entry Extension flags. The "UPDATE" extension
+ * flag must be set in this value. A corresponding directory
+ * entry with the same type and ordinal values but *without* the
+ * "UPDATE" extension flag must also exist. The other flags of
+ * the extension must be identical between the active and update
+ * entries.
*/
- #define HWRM_STAT_CTX_ALLOC_INPUT_STAT_CTX_FLAGS_ROCE UINT32_C(0x1)
- uint8_t unused_0[3];
+ uint16_t unused_0;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_stat_ctx_alloc_output {
+/* Output (16 bytes) */
+struct hwrm_nvm_verify_update_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -10884,11 +27452,10 @@ struct hwrm_stat_ctx_alloc_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t stat_ctx_id;
- /* This is the statistics context ID value. */
- uint8_t unused_0;
+ uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -10900,10 +27467,14 @@ struct hwrm_stat_ctx_alloc_output {
*/
} __attribute__((packed));
-/* hwrm_stat_ctx_free */
-/* Description: This command is used to free a stat context. */
-/* Input (24 bytes) */
-struct hwrm_stat_ctx_free_input {
+/* hwrm_nvm_install_update */
+/*
+ * Description: Install a staged NVM package. A package file must first be
+ * staged into the "UPDATE" NVM item. This staging is accomplished using the
+ * nvm_write and/or nvm_modify HWRM commands.
+ */
+/* Input (24 bytes) */
+struct hwrm_nvm_install_update_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -10930,13 +27501,52 @@ struct hwrm_stat_ctx_free_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t stat_ctx_id;
- /* ID of the statistics context that is being queried. */
- uint32_t unused_0;
+ uint32_t install_type;
+ /*
+ * Installation type. If the value 3 through 0xffff is used,
+ * only packaged items with that type value will be installed
+ * and conditional installation directives for those packaged
+ * items will be over-ridden (i.e. 'create' or 'replace' will be
+ * treated as 'install').
+ */
+ /*
+ * Perform a normal package installation.
+ * Conditional installation directives (e.g.
+ * 'create' and 'replace') of packaged items
+ * will be followed.
+ */
+ #define HWRM_NVM_INSTALL_UPDATE_INPUT_INSTALL_TYPE_NORMAL 0x0UL
+ /*
+ * Install all packaged items regardless of
+ * installation directive (i.e. treat all
+ * packaged items as though they have an
+ * installation directive of 'install').
+ */
+ #define HWRM_NVM_INSTALL_UPDATE_INPUT_INSTALL_TYPE_ALL 0xffffffffUL
+ uint16_t flags;
+ /*
+ * If set to 1, then securely erase all unused locations in
+ * persistent storage.
+ */
+ #define HWRM_NVM_INSTALL_UPDATE_INPUT_FLAGS_ERASE_UNUSED_SPACE 0x1UL
+ /*
+ * If set to 1, then unspecifed images, images not in the
+ * package file, will be safely deleted. When combined with
+ * erase_unused_space then unspecified images will be securely
+ * erased.
+ */
+ #define HWRM_NVM_INSTALL_UPDATE_INPUT_FLAGS_REMOVE_UNUSED_PKG 0x2UL
+ /*
+ * If set to 1, FW will defragment the NVM if defragmentation is
+ * required for the update. Allow additional time for this
+ * command to complete if this bit is set to 1.
+ */
+ #define HWRM_NVM_INSTALL_UPDATE_INPUT_FLAGS_ALLOWED_TO_DEFRAG 0x4UL
+ uint16_t unused_0;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_stat_ctx_free_output {
+/* Output (24 bytes) */
+struct hwrm_nvm_install_update_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -10952,11 +27562,49 @@ struct hwrm_stat_ctx_free_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t stat_ctx_id;
- /* This is the statistics context ID value. */
+ uint64_t installed_items;
+ /*
+ * Bit-mask of successfully installed items. Bit-0 corresponding
+ * to the first packaged item, Bit-1 for the second item, etc. A
+ * value of 0 indicates that no items were successfully
+ * installed.
+ */
+ uint8_t result;
+ /* result is 8 b */
+ /* There was no problem with the package installation. */
+ #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESULT_SUCCESS 0x0UL
+ uint8_t problem_item;
+ /* problem_item is 8 b */
+ /* There was no problem with any packaged items. */
+ #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_PROBLEM_ITEM_NONE 0x0UL
+ /* There was a problem with the NVM package itself. */
+ #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_PROBLEM_ITEM_PACKAGE 0xffUL
+ uint8_t reset_required;
+ /* reset_required is 8 b */
+ /*
+ * No reset is required for installed/updated
+ * firmware or microcode to take effect.
+ */
+ #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESET_INPUTUIRED_NONE 0x0UL
+ /*
+ * A PCIe reset (e.g. system reboot) is required
+ * for newly installed/updated firmware or
+ * microcode to take effect.
+ */
+ #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESET_INPUTUIRED_PCI 0x1UL
+ /*
+ * A controller power reset (e.g. system power-
+ * cycle) is required for newly
+ * installed/updated firmware or microcode to
+ * take effect. Some newly installed/updated
+ * firmware or microcode may still take effect
+ * upon the next PCIe reset.
+ */
+ #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESET_INPUTUIRED_POWER 0x2UL
uint8_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
+ uint8_t unused_3;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -10968,10 +27616,25 @@ struct hwrm_stat_ctx_free_output {
*/
} __attribute__((packed));
-/* hwrm_stat_ctx_clr_stats */
-/* Description: This command clears statistics of a context. */
-/* Input (24 bytes) */
-struct hwrm_stat_ctx_clr_stats_input {
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_nvm_install_update_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_NVM_INSTALL_UPDATE_CMD_ERR_CODE_UNKNOWN 0x0UL
+ /* Unable to complete operation due to fragmentation */
+ #define HWRM_NVM_INSTALL_UPDATE_CMD_ERR_CODE_FRAG_ERR 0x1UL
+ /* nvm is completely full. */
+ #define HWRM_NVM_INSTALL_UPDATE_CMD_ERR_CODE_NO_SPACE 0x2UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* hwrm_nvm_flush */
+/* Input (16 bytes) */
+struct hwrm_nvm_flush_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -10998,13 +27661,10 @@ struct hwrm_stat_ctx_clr_stats_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t stat_ctx_id;
- /* ID of the statistics context that is being queried. */
- uint32_t unused_0;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_stat_ctx_clr_stats_output {
+/* Output (16 bytes) */
+struct hwrm_nvm_flush_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -11035,48 +27695,90 @@ struct hwrm_stat_ctx_clr_stats_output {
*/
} __attribute__((packed));
-/* hwrm_stat_ctx_query */
-/* Description: This command returns statistics of a context. */
-/* Input (24 bytes) */
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_nvm_flush_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_NVM_FLUSH_CMD_ERR_CODE_UNKNOWN 0x0UL
+ /* flush could not be performed */
+ #define HWRM_NVM_FLUSH_CMD_ERR_CODE_FAIL 0x1UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
-struct hwrm_stat_ctx_query_input {
+/* hwrm_nvm_get_variable */
+/* Input (40 bytes) */
+struct hwrm_nvm_get_variable_input {
uint16_t req_type;
/*
- * This value indicates what type of request this is. The format for the
- * rest of the command is determined by this field.
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
*/
uint16_t cmpl_ring;
/*
- * This value indicates the what completion ring the request will be
- * optionally completed on. If the value is -1, then no CR completion
- * will be generated. Any other value must be a valid CR ring_id value
- * for this function.
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
*/
uint16_t seq_id;
/* This value indicates the command sequence number. */
uint16_t target_id;
/*
- * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
- * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
*/
uint64_t resp_addr;
/*
- * This is the host address where the response will be written when the
- * request is complete. This area must be 16B aligned and must be
- * cleared to zero before the request is made.
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
*/
- uint32_t stat_ctx_id;
- /* ID of the statistics context that is being queried. */
- uint32_t unused_0;
+ uint64_t dest_data_addr;
+ /* This is the host address where nvm variable will be stored */
+ uint16_t data_len;
+ /* size of data in bits */
+ uint16_t option_num;
+ /* nvm cfg option number */
+ /* reserved. */
+ #define HWRM_NVM_GET_VARIABLE_INPUT_OPTION_NUM_RSVD_0 0x0UL
+ /* reserved. */
+ #define HWRM_NVM_GET_VARIABLE_INPUT_OPTION_NUM_RSVD_FFFF 0xffffUL
+ uint16_t dimensions;
+ /*
+ * Number of dimensions for this nvm configuration variable.
+ * This value indicates how many of the indexN values to use. A
+ * value of 0 means that none of the indexN values are valid. A
+ * value of 1 requires at index0 is valued, a value of 2
+ * requires that index0 and index1 are valid, and so forth
+ */
+ uint16_t index_0;
+ /* index for the 1st dimensions */
+ uint16_t index_1;
+ /* index for the 2nd dimensions */
+ uint16_t index_2;
+ /* index for the 3rd dimensions */
+ uint16_t index_3;
+ /* index for the 4th dimensions */
+ uint8_t flags;
+ /*
+ * When this bit is set to 1, the factory default value will be
+ * returned, 0 returns the operational value.
+ */
+ #define HWRM_NVM_GET_VARIABLE_INPUT_FLAGS_FACTORY_DFLT 0x1UL
+ uint8_t unused_0;
} __attribute__((packed));
-/* Output (176 bytes) */
-
-struct hwrm_stat_ctx_query_output {
+/* Output (16 bytes) */
+struct hwrm_nvm_get_variable_output {
uint16_t error_code;
/*
- * Pass/Fail or error type Note: receiver to verify the in parameters,
- * and fail the call with an error when appropriate
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
*/
uint16_t req_type;
/* This field returns the type of original request. */
@@ -11084,76 +27786,65 @@ struct hwrm_stat_ctx_query_output {
/* This field provides original sequence number of the command. */
uint16_t resp_len;
/*
- * This field is the length of the response in bytes. The last byte of
- * the response is a valid flag that will read as '1' when the command
- * has been completely written to memory.
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
*/
- uint64_t tx_ucast_pkts;
- /* Number of transmitted unicast packets */
- uint64_t tx_mcast_pkts;
- /* Number of transmitted multicast packets */
- uint64_t tx_bcast_pkts;
- /* Number of transmitted broadcast packets */
- uint64_t tx_err_pkts;
- /* Number of transmitted packets with error */
- uint64_t tx_drop_pkts;
- /* Number of dropped packets on transmit path */
- uint64_t tx_ucast_bytes;
- /* Number of transmitted bytes for unicast traffic */
- uint64_t tx_mcast_bytes;
- /* Number of transmitted bytes for multicast traffic */
- uint64_t tx_bcast_bytes;
- /* Number of transmitted bytes for broadcast traffic */
- uint64_t rx_ucast_pkts;
- /* Number of received unicast packets */
- uint64_t rx_mcast_pkts;
- /* Number of received multicast packets */
- uint64_t rx_bcast_pkts;
- /* Number of received broadcast packets */
- uint64_t rx_err_pkts;
- /* Number of received packets with error */
- uint64_t rx_drop_pkts;
- /* Number of dropped packets on received path */
- uint64_t rx_ucast_bytes;
- /* Number of received bytes for unicast traffic */
- uint64_t rx_mcast_bytes;
- /* Number of received bytes for multicast traffic */
- uint64_t rx_bcast_bytes;
- /* Number of received bytes for broadcast traffic */
- uint64_t rx_agg_pkts;
- /* Number of aggregated unicast packets */
- uint64_t rx_agg_bytes;
- /* Number of aggregated unicast bytes */
- uint64_t rx_agg_events;
- /* Number of aggregation events */
- uint64_t rx_agg_aborts;
- /* Number of aborted aggregations */
- uint32_t unused_0;
+ uint16_t data_len;
+ /* size of data of the actual variable retrieved in bits */
+ uint16_t option_num;
+ /*
+ * option_num is the option number for the data retrieved. It is
+ * possible in the future that the option number returned would
+ * be different than requested. This condition could occur if an
+ * option is deprecated and a new option id is defined with
+ * similar characteristics, but has a slightly different
+ * definition. This also makes it convenient for the caller to
+ * identify the variable result with the option id from the
+ * response.
+ */
+ /* reserved. */
+ #define HWRM_NVM_GET_VARIABLE_OUTPUT_OPTION_NUM_RSVD_0 0x0UL
+ /* reserved. */
+ #define HWRM_NVM_GET_VARIABLE_OUTPUT_OPTION_NUM_RSVD_FFFF 0xffffUL
+ uint8_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
- uint8_t unused_3;
uint8_t valid;
/*
- * This field is used in Output records to indicate that the output is
- * completely written to RAM. This field should be read as '1' to
- * indicate that the output has been completely written. When writing a
- * command completion or response to an internal processor, the order of
- * writes has to be such that this field is written last.
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_nvm_get_variable_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_NVM_GET_VARIABLE_CMD_ERR_CODE_UNKNOWN 0x0UL
+ /* variable does not exist */
+ #define HWRM_NVM_GET_VARIABLE_CMD_ERR_CODE_VAR_NOT_EXIST 0x1UL
+ /*
+ * configuration is corrupted and the variable
+ * cannot be saved
*/
+ #define HWRM_NVM_GET_VARIABLE_CMD_ERR_CODE_CORRUPT_VAR 0x2UL
+ /* length specified is too small */
+ #define HWRM_NVM_GET_VARIABLE_CMD_ERR_CODE_LEN_TOO_SHORT 0x3UL
+ uint8_t unused_0[7];
} __attribute__((packed));
-/* hwrm_exec_fwd_resp */
-/*
- * Description: This command is used to send an encapsulated request to the
- * HWRM. This command instructs the HWRM to execute the request and forward the
- * response of the encapsulated request to the location specified in the
- * original request that is encapsulated. The target id of this command shall be
- * set to 0xFFFF (HWRM). The response location in this command shall be used to
- * acknowledge the receipt of the encapsulated request and forwarding of the
- * response.
- */
-/* Input (128 bytes) */
-struct hwrm_exec_fwd_resp_input {
+/* hwrm_nvm_set_variable */
+/* Input (40 bytes) */
+struct hwrm_nvm_set_variable_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -11180,24 +27871,53 @@ struct hwrm_exec_fwd_resp_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t encap_request[26];
- /*
- * This is an encapsulated request. This request should be
- * executed by the HWRM and the response should be provided in
- * the response buffer inside the encapsulated request.
- */
- uint16_t encap_resp_target_id;
- /*
- * This value indicates the target id of the response to the
- * encapsulated request. 0x0 - 0xFFF8 - Used for function ids
- * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF -
- * HWRM
- */
- uint16_t unused_0[3];
+ uint64_t src_data_addr;
+ /* This is the host address where nvm variable will be copied from */
+ uint16_t data_len;
+ /* size of data in bits */
+ uint16_t option_num;
+ /* nvm cfg option number */
+ /* reserved. */
+ #define HWRM_NVM_SET_VARIABLE_INPUT_OPTION_NUM_RSVD_0 0x0UL
+ /* reserved. */
+ #define HWRM_NVM_SET_VARIABLE_INPUT_OPTION_NUM_RSVD_FFFF 0xffffUL
+ uint16_t dimensions;
+ /*
+ * Number of dimensions for this nvm configuration variable.
+ * This value indicates how many of the indexN values to use. A
+ * value of 0 means that none of the indexN values are valid. A
+ * value of 1 requires at index0 is valued, a value of 2
+ * requires that index0 and index1 are valid, and so forth
+ */
+ uint16_t index_0;
+ /* index for the 1st dimensions */
+ uint16_t index_1;
+ /* index for the 2nd dimensions */
+ uint16_t index_2;
+ /* index for the 3rd dimensions */
+ uint16_t index_3;
+ /* index for the 4th dimensions */
+ uint8_t flags;
+ /*
+ * When this bit is 1, flush internal cache after this write
+ * operation (see hwrm_nvm_flush command.)
+ */
+ #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_FORCE_FLUSH 0x1UL
+ /* encryption method */
+ #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_MASK 0xeUL
+ #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_SFT 1
+ /* No encryption. */
+ #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_NONE (0x0UL << 1)
+ /* one-way encryption. */
+ #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_HMAC_SHA1 \
+ (0x1UL << 1)
+ #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_LAST \
+ NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_HMAC_SHA1
+ uint8_t unused_0;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_exec_fwd_resp_output {
+/* Output (16 bytes) */
+struct hwrm_nvm_set_variable_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -11228,18 +27948,28 @@ struct hwrm_exec_fwd_resp_output {
*/
} __attribute__((packed));
-/* hwrm_reject_fwd_resp */
-/*
- * Description: This command is used to send an encapsulated request to the
- * HWRM. This command instructs the HWRM to reject the request and forward the
- * error response of the encapsulated request to the location specified in the
- * original request that is encapsulated. The target id of this command shall be
- * set to 0xFFFF (HWRM). The response location in this command shall be used to
- * acknowledge the receipt of the encapsulated request and forwarding of the
- * response.
- */
-/* Input (128 bytes) */
-struct hwrm_reject_fwd_resp_input {
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_nvm_set_variable_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_NVM_SET_VARIABLE_CMD_ERR_CODE_UNKNOWN 0x0UL
+ /* variable does not exist */
+ #define HWRM_NVM_SET_VARIABLE_CMD_ERR_CODE_VAR_NOT_EXIST 0x1UL
+ /*
+ * configuration is corrupted and the variable
+ * cannot be saved
+ */
+ #define HWRM_NVM_SET_VARIABLE_CMD_ERR_CODE_CORRUPT_VAR 0x2UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* hwrm_nvm_validate_option */
+/* Input (40 bytes) */
+struct hwrm_nvm_validate_option_input {
uint16_t req_type;
/*
* This value indicates what type of request this is. The format
@@ -11266,25 +27996,37 @@ struct hwrm_reject_fwd_resp_input {
* when the request is complete. This area must be 16B aligned
* and must be cleared to zero before the request is made.
*/
- uint32_t encap_request[26];
- /*
- * This is an encapsulated request. This request should be
- * rejected by the HWRM and the error response should be
- * provided in the response buffer inside the encapsulated
- * request.
- */
- uint16_t encap_resp_target_id;
- /*
- * This value indicates the target id of the response to the
- * encapsulated request. 0x0 - 0xFFF8 - Used for function ids
- * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF -
- * HWRM
- */
- uint16_t unused_0[3];
+ uint64_t src_data_addr;
+ /* This is the host address where nvm variable will be copied from */
+ uint16_t data_len;
+ /* size of data in bits */
+ uint16_t option_num;
+ /* nvm cfg option number */
+ /* reserved. */
+ #define HWRM_NVM_VALIDATE_OPTION_INPUT_OPTION_NUM_RSVD_0 0x0UL
+ /* reserved. */
+ #define HWRM_NVM_VALIDATE_OPTION_INPUT_OPTION_NUM_RSVD_FFFF 0xffffUL
+ uint16_t dimensions;
+ /*
+ * Number of dimensions for this nvm configuration variable.
+ * This value indicates how many of the indexN values to use. A
+ * value of 0 means that none of the indexN values are valid. A
+ * value of 1 requires at index0 is valued, a value of 2
+ * requires that index0 and index1 are valid, and so forth
+ */
+ uint16_t index_0;
+ /* index for the 1st dimensions */
+ uint16_t index_1;
+ /* index for the 2nd dimensions */
+ uint16_t index_2;
+ /* index for the 3rd dimensions */
+ uint16_t index_3;
+ /* index for the 4th dimensions */
+ uint16_t unused_0;
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_reject_fwd_resp_output {
+/* Output (16 bytes) */
+struct hwrm_nvm_validate_option_output {
uint16_t error_code;
/*
* Pass/Fail or error type Note: receiver to verify the in
@@ -11300,10 +28042,22 @@ struct hwrm_reject_fwd_resp_output {
* byte of the response is a valid flag that will read as '1'
* when the command has been completely written to memory.
*/
- uint32_t unused_0;
- uint8_t unused_1;
+ uint8_t result;
+ /*
+ * indicates that the value provided for the
+ * option is not matching with the saved data.
+ */
+ #define HWRM_NVM_VALIDATE_OPTION_OUTPUT_RESULT_NOT_MATCH 0x0UL
+ /*
+ * indicates that the value provided for the
+ * option is matching the saved data.
+ */
+ #define HWRM_NVM_VALIDATE_OPTION_OUTPUT_RESULT_MATCH 0x1UL
+ uint8_t unused_0;
+ uint16_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
+ uint8_t unused_4;
uint8_t valid;
/*
* This field is used in Output records to indicate that the
@@ -11315,153 +28069,502 @@ struct hwrm_reject_fwd_resp_output {
*/
} __attribute__((packed));
-/* hwrm_nvm_get_dir_entries */
-/* Input (24 bytes) */
-struct hwrm_nvm_get_dir_entries_input {
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_nvm_validate_option_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_NVM_VALIDATE_OPTION_CMD_ERR_CODE_UNKNOWN 0x0UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/*
+ * Note: This section documents the Host Structures used between software and
+ * RoCE control firmware.
+ */
+/* hwrm_selftest_qlist */
+/*
+ * Description: This function is called by a driver to determine which selftests
+ * are available to be run against the requested function.
+ */
+/* Input (16 bytes) */
+struct hwrm_selftest_qlist_input {
uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
uint16_t seq_id;
+ /* This value indicates the command sequence number. */
uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
uint64_t resp_addr;
- uint64_t host_dest_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
} __attribute__((packed));
-/* Output (16 bytes) */
-struct hwrm_nvm_get_dir_entries_output {
+/* Output (280 bytes) */
+struct hwrm_selftest_qlist_output {
uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
uint16_t req_type;
+ /* This field returns the type of original request. */
uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
uint16_t resp_len;
- uint32_t unused_0;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t num_tests;
+ /*
+ * This field represents the number of tests available to be
+ * requested by a driver.
+ */
+ uint8_t available_tests;
+ /* This field indicates which self-test is available to be run. */
+ /* Can run the NVM test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_AVAILABLE_TESTS_NVM_TEST 0x1UL
+ /* Can run the link test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_AVAILABLE_TESTS_LINK_TEST 0x2UL
+ /* Can run the register test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_AVAILABLE_TESTS_REGISTER_TEST 0x4UL
+ /* Can run the memory test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_AVAILABLE_TESTS_MEMORY_TEST 0x8UL
+ /* Can run the PCIe serdes test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_AVAILABLE_TESTS_PCIE_SERDES_TEST \
+ 0x10UL
+ /* Can run the Ethernet serdes test. */
+ #define \
+ HWRM_SELFTEST_QLIST_OUTPUT_AVAILABLE_TESTS_ETHERNET_SERDES_TEST \
+ 0x20UL
+ uint8_t offline_tests;
+ /* The NVM test is an offline test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_OFFLINE_TESTS_NVM_TEST 0x1UL
+ /* The link test is an offline test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_OFFLINE_TESTS_LINK_TEST 0x2UL
+ /* The register test is an offline test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_OFFLINE_TESTS_REGISTER_TEST 0x4UL
+ /* The memory test is an offline test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_OFFLINE_TESTS_MEMORY_TEST 0x8UL
+ /* The PCIe serdes test is an offline test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_OFFLINE_TESTS_PCIE_SERDES_TEST 0x10UL
+ /* The Ethernet serdes test is an offline test. */
+ #define HWRM_SELFTEST_QLIST_OUTPUT_OFFLINE_TESTS_ETHERNET_SERDES_TEST \
+ 0x20UL
+ uint8_t unused_0;
+ uint16_t test_timeout;
+ /*
+ * This field represents the the maximum timeout for all the
+ * tests to complete in milliseconds.
+ */
uint8_t unused_1;
uint8_t unused_2;
- uint8_t unused_3;
+ char test0_name[32];
+ /*
+ * This field represents the name of the NVM test (ASCII chars
+ * with NULL at the end).
+ */
+ char test1_name[32];
+ /*
+ * This field represents the name of the link test (ASCII chars
+ * with NULL at the end).
+ */
+ char test2_name[32];
+ /*
+ * This field represents the name of the register test (ASCII
+ * chars with NULL at the end).
+ */
+ char test3_name[32];
+ /*
+ * This field represents the name of the memory test (ASCII
+ * chars with NULL at the end).
+ */
+ char test4_name[32];
+ /*
+ * This field represents the name of the PCIe serdes test (ASCII
+ * chars with NULL at the end).
+ */
+ char test5_name[32];
+ /*
+ * This field represents the name of the Ethernet serdes test
+ * (ASCII chars with NULL at the end).
+ */
+ char test6_name[32];
+ /*
+ * This field represents the name of some future test (ASCII
+ * chars with NULL at the end).
+ */
+ char test7_name[32];
+ /*
+ * This field represents the name of some future test (ASCII
+ * chars with NULL at the end).
+ */
+ uint32_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t unused_6;
uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
} __attribute__((packed));
-
-/* hwrm_nvm_erase_dir_entry */
+/* hwrm_selftest_exec */
+/*
+ * Description: This function is called by a driver to request which self tests
+ * are to be run.
+ */
/* Input (24 bytes) */
-struct hwrm_nvm_erase_dir_entry_input {
+struct hwrm_selftest_exec_input {
uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
uint16_t seq_id;
+ /* This value indicates the command sequence number. */
uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
uint64_t resp_addr;
- uint16_t dir_idx;
- uint16_t unused_0[3];
-};
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint8_t flags;
+ /* This field indicates which self-test is being requested to run. */
+ /* Run the NVM test. */
+ #define HWRM_SELFTEST_EXEC_INPUT_FLAGS_NVM_TEST 0x1UL
+ /* Run the link test. */
+ #define HWRM_SELFTEST_EXEC_INPUT_FLAGS_LINK_TEST 0x2UL
+ /* Run the register test. */
+ #define HWRM_SELFTEST_EXEC_INPUT_FLAGS_REGISTER_TEST 0x4UL
+ /* Run the memory test. */
+ #define HWRM_SELFTEST_EXEC_INPUT_FLAGS_MEMORY_TEST 0x8UL
+ /* Run the PCIe serdes test. */
+ #define HWRM_SELFTEST_EXEC_INPUT_FLAGS_PCIE_SERDES_TEST 0x10UL
+ /* Run the Ethernet serdes test. */
+ #define HWRM_SELFTEST_EXEC_INPUT_FLAGS_ETHERNET_SERDES_TEST 0x20UL
+ uint8_t unused_0[7];
+} __attribute__((packed));
/* Output (16 bytes) */
-struct hwrm_nvm_erase_dir_entry_output {
+struct hwrm_selftest_exec_output {
uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
uint16_t req_type;
+ /* This field returns the type of original request. */
uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
uint16_t resp_len;
- uint32_t unused_0;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t requested_tests;
+ /* The following tests were requested to be run. */
+ /* A reqeust was made to run the NVM test. */
+ #define HWRM_SELFTEST_EXEC_OUTPUT_INPUTUESTED_TESTS_NVM_TEST 0x1UL
+ /* A request was made to run the link test. */
+ #define HWRM_SELFTEST_EXEC_OUTPUT_INPUTUESTED_TESTS_LINK_TEST 0x2UL
+ /* A request was made to run the register test. */
+ #define HWRM_SELFTEST_EXEC_OUTPUT_INPUTUESTED_TESTS_REGISTER_TEST 0x4UL
+ /* A request was made to run the memory test. */
+ #define HWRM_SELFTEST_EXEC_OUTPUT_INPUTUESTED_TESTS_MEMORY_TEST 0x8UL
+ /* A request was made to run the PCIe serdes test. */
+ #define \
+ HWRM_SELFTEST_EXEC_OUTPUT_INPUTUESTED_TESTS_PCIE_SERDES_TEST 0x10UL
+ /* A request was made to run the Ethernet serdes test. */
+ #define \
+ HWRM_SELFTEST_EXEC_OUTPUT_INPUTUESTED_TESTS_ETHERNET_SERDES_TEST \
+ 0x20UL
+ uint8_t test_success;
+ /*
+ * If a test was requested to be run as seen in the
+ * requested_tests field, this bit indicates whether the test
+ * was successful(1) or failed(0).
+ */
+ /*
+ * If requested, a value of 1 indicates the NVM test completed
+ * successfully.
+ */
+ #define HWRM_SELFTEST_EXEC_OUTPUT_TEST_SUCCESS_NVM_TEST 0x1UL
+ /*
+ * If requested, a value of 1 indicates the link test completed
+ * successfully.
+ */
+ #define HWRM_SELFTEST_EXEC_OUTPUT_TEST_SUCCESS_LINK_TEST 0x2UL
+ /*
+ * If requested, a value of 1 indicates the register test
+ * completed successfully.
+ */
+ #define HWRM_SELFTEST_EXEC_OUTPUT_TEST_SUCCESS_REGISTER_TEST 0x4UL
+ /*
+ * If requested, a value of 1 indicates the memory test
+ * completed successfully.
+ */
+ #define HWRM_SELFTEST_EXEC_OUTPUT_TEST_SUCCESS_MEMORY_TEST 0x8UL
+ /*
+ * If requested, a value of 1 indicates the PCIe serdes test
+ * completed successfully.
+ */
+ #define HWRM_SELFTEST_EXEC_OUTPUT_TEST_SUCCESS_PCIE_SERDES_TEST 0x10UL
+ /*
+ * If requested, a value of 1 indicates the Ethernet serdes test
+ * completed successfully.
+ */
+ #define \
+ HWRM_SELFTEST_EXEC_OUTPUT_TEST_SUCCESS_ETHERNET_SERDES_TEST 0x20UL
+ uint8_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
+ uint8_t unused_4;
uint8_t valid;
-};
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
-/* hwrm_nvm_get_dir_info */
+/* hwrm_selftest_irq */
+/*
+ * Description: This function is called by a driver to request the interrupt
+ * test be run. In response to this request the interrupt associated with the
+ * completion ring specified in the cmpl_ring field will be asserted to the
+ * host.
+ */
/* Input (16 bytes) */
-struct hwrm_nvm_get_dir_info_input {
+struct hwrm_selftest_irq_input {
uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
uint16_t seq_id;
+ /* This value indicates the command sequence number. */
uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
} __attribute__((packed));
-/* Output (24 bytes) */
-struct hwrm_nvm_get_dir_info_output {
+/* Output (16 bytes) */
+struct hwrm_selftest_irq_output {
uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
uint16_t req_type;
+ /* This field returns the type of original request. */
uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
uint16_t resp_len;
- uint32_t entries;
- uint32_t entry_length;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
uint32_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
uint8_t unused_3;
uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
} __attribute__((packed));
-
-/* hwrm_nvm_write */
-/* Input (48 bytes) */
-struct hwrm_nvm_write_input {
- uint16_t req_type;
- uint16_t cmpl_ring;
- uint16_t seq_id;
- uint16_t target_id;
- uint64_t resp_addr;
- uint64_t host_src_addr;
- uint16_t dir_type;
- uint16_t dir_ordinal;
- uint16_t dir_ext;
- uint16_t dir_attr;
- uint32_t dir_data_length;
- uint16_t option;
- uint16_t flags;
- #define NVM_WRITE_REQ_FLAGS_KEEP_ORIG_ACTIVE_IMG 0x1UL
- uint32_t dir_item_length;
- uint32_t unused_0;
-};
-
-/* Output (16 bytes) */
-struct hwrm_nvm_write_output {
- uint16_t error_code;
- uint16_t req_type;
- uint16_t seq_id;
- uint16_t resp_len;
- uint32_t dir_item_length;
- uint16_t dir_idx;
- uint8_t unused_0;
- uint8_t valid;
-};
-/* hwrm_nvm_read */
-/* Input (40 bytes) */
-struct hwrm_nvm_read_input {
+/* hwrm_selftest_retreive_serdes_data */
+/*
+ * Description: This function is called by a driver to retreieve the data
+ * collected when running the previous PCIe or Ethernet serdes test. The driver
+ * can use multiple calls to this command to retreive the entire stored buffer
+ * in the event it cannot do so with a single call.
+ */
+/* Input (32 bytes) */
+struct hwrm_selftest_retreive_serdes_data_input {
uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
uint16_t seq_id;
+ /* This value indicates the command sequence number. */
uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
uint64_t resp_addr;
- uint64_t host_dest_addr;
- uint16_t dir_idx;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint64_t resp_data_addr;
+ /* Host address data is to DMA'd to. */
+ uint32_t resp_data_offset;
+ /*
+ * This field contains the offset into the captured data to
+ * begin copying the data to the host from. This should be set
+ * to 0 on the initial call to this command.
+ */
+ uint16_t data_len;
+ /*
+ * Size of the buffer pointed to by resp_data_addr. The firmware
+ * may use this entire buffer or less than the entire buffer,
+ * but never more.
+ */
+ uint8_t flags;
+ /*
+ * This field allows this command to request the individual
+ * serdes tests to be run using this command.
+ */
+ /* Unused. */
+ #define \
+ HWRM_SELFTEST_RETREIVE_SERDES_DATA_INPUT_FLAGS_UNUSED_TEST_MASK \
+ 0xfUL
+ #define HWRM_SELFTEST_RETREIVE_SERDES_DATA_INPUT_FLAGS_UNUSED_TEST_SFT 0
+ /* Run the PCIe serdes test. */
+ #define \
+ HWRM_SELFTEST_RETREIVE_SERDES_DATA_INPUT_FLAGS_PCIE_SERDES_TEST \
+ 0x10UL
+ /* Run the Ethernet serdes test. */
+ #define \
+ HWRM_SELFTEST_RETREIVE_SERDES_DATA_INPUT_FLAGS_ETHERNET_SERDES_TEST \
+ 0x20UL
uint8_t unused_0;
- uint8_t unused_1;
- uint32_t offset;
- uint32_t len;
- uint32_t unused_2;
} __attribute__((packed));
/* Output (16 bytes) */
-struct hwrm_nvm_read_output {
+struct hwrm_selftest_retreive_serdes_data_output {
uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
uint16_t req_type;
+ /* This field returns the type of original request. */
uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
uint16_t resp_len;
- uint32_t unused_0;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t total_data_len;
+ /* Total length of stored data. */
+ uint16_t copied_data_len;
+ /*
+ * Amount of data DMA'd to host by this call. The driver can use
+ * this field along with the total_data_len field above to
+ * determine the value to write to the resp_data_offset field in
+ * the next call if more than one call to these commands is
+ * required to retreive all the stored data.
+ */
+ uint8_t unused_0;
uint8_t unused_1;
uint8_t unused_2;
- uint8_t unused_3;
uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
} __attribute__((packed));
/* Hardware Resource Manager Specification */
-/* Description: This structure is used to specify port description. */
+/*
+ * Description: This header structure is written before dumping the register
+ * range.
+ */
/*
* Note: The Hardware Resource Manager (HWRM) manages various hardware resources
* inside the chip. The HWRM is implemented in firmware, and runs on embedded
* processors inside the chip. This firmware service is vital part of the chip.
* The chip can not be used by a driver or HWRM client without the HWRM.
*/
-/* Input (16 bytes) */
+/* Input (16 bytes) */
struct input {
uint16_t req_type;
/*
@@ -11491,7 +28594,7 @@ struct input {
*/
} __attribute__((packed));
-/* Output (8 bytes) */
+/* Output (8 bytes) */
struct output {
uint16_t error_code;
/*
@@ -11513,42 +28616,313 @@ struct output {
/* Short Command Structure (16 bytes) */
struct hwrm_short_input {
uint16_t req_type;
+ /*
+ * This field indicates the type of request in the request
+ * buffer. The format for the rest of the command (request) is
+ * determined by this field.
+ */
uint16_t signature;
- #define HWRM_SHORT_REQ_SIGNATURE_SHORT_CMD (UINT32_C(0x4321))
+ /*
+ * This field indicates a signature that is used to identify
+ * short form of the command listed here. This field shall be
+ * set to 17185 (0x4321).
+ */
+ /* Signature indicating this is a short form of HWRM command */
+ #define HWRM_SHORT_INPUT_SIGNATURE_SHORT_CMD 0x4321UL
uint16_t unused_0;
+ /* Reserved for future use. */
uint16_t size;
+ /* This value indicates the length of the request. */
uint64_t req_addr;
+ /*
+ * This is the host address where the request was written. This
+ * area must be 16B aligned.
+ */
+} __attribute__((packed));
+
+#define HWRM_GET_HWRM_INPUT_TYPE(x) \
+ ((x) == 0x99 ? "HWRM_CFA_NTUPLE_FILTER_ALLOC": \
+ ((x) == 0x90 ? "HWRM_CFA_L2_FILTER_ALLOC": \
+ ((x) == 0x91 ? "HWRM_CFA_L2_FILTER_FREE": \
+ ((x) == 0x92 ? "HWRM_CFA_L2_FILTER_CFG": \
+ ((x) == 0x93 ? "HWRM_CFA_L2_SET_RX_MASK": \
+ ((x) == 0x94 ? "HWRM_CFA_VLAN_ANTISPOOF_CFG": \
+ ((x) == 0x95 ? "HWRM_CFA_TUNNEL_FILTER_ALLOC": \
+ ((x) == 0x96 ? "HWRM_CFA_TUNNEL_FILTER_FREE": \
+ ((x) == 0x10 ? "RESERVED1": \
+ ((x) == 0x11 ? "HWRM_FUNC_RESET": \
+ ((x) == 0x12 ? "HWRM_FUNC_GETFID": \
+ ((x) == 0x13 ? "HWRM_FUNC_VF_ALLOC": \
+ ((x) == 0x14 ? "HWRM_FUNC_VF_FREE": \
+ ((x) == 0x15 ? "HWRM_FUNC_QCAPS": \
+ ((x) == 0x16 ? "HWRM_FUNC_QCFG": \
+ ((x) == 0x17 ? "HWRM_FUNC_CFG": \
+ ((x) == 0x18 ? "HWRM_FUNC_QSTATS": \
+ ((x) == 0x19 ? "HWRM_FUNC_CLR_STATS": \
+ ((x) == 0xe0 ? "HWRM_TEMP_MONITOR_QUERY": \
+ ((x) == 0x1a ? "HWRM_FUNC_DRV_UNRGTR": \
+ ((x) == 0x1b ? "HWRM_FUNC_VF_RESC_FREE": \
+ ((x) == 0x1c ? "HWRM_FUNC_VF_VNIC_IDS_QUERY": \
+ ((x) == 0x1d ? "HWRM_FUNC_DRV_RGTR": \
+ ((x) == 0x1e ? "HWRM_FUNC_DRV_QVER": \
+ ((x) == 0x1f ? "HWRM_FUNC_BUF_RGTR": \
+ ((x) == 0x9a ? "HWRM_CFA_NTUPLE_FILTER_FREE": \
+ ((x) == 0x9b ? "HWRM_CFA_NTUPLE_FILTER_CFG": \
+ ((x) == 0xd3 ? "HWRM_FWD_ASYNC_EVENT_CMPL": \
+ ((x) == 0xd2 ? "HWRM_FWD_OUTPUT": \
+ ((x) == 0xd1 ? "HWRM_REJECT_FWD_OUTPUT": \
+ ((x) == 0xd0 ? "HWRM_EXEC_FWD_RESP": \
+ ((x) == 0xfffa ? "HWRM_NVM_GET_DIR_ENTRIES": \
+ ((x) == 0xc0 ? "HWRM_FW_RESET": \
+ ((x) == 0xc1 ? "HWRM_FW_QSTATUS": \
+ ((x) == 0x70 ? "HWRM_VNIC_RSS_COS_LB_CTX_ALLOC": \
+ ((x) == 0x71 ? "HWRM_VNIC_RSS_COS_LB_CTX_FREE": \
+ ((x) == 0xb1 ? "HWRM_STAT_CTX_FREE": \
+ ((x) == 0xb0 ? "HWRM_STAT_CTX_ALLOC": \
+ ((x) == 0xb3 ? "HWRM_STAT_CTX_CLR_STATS": \
+ ((x) == 0xb2 ? "HWRM_STAT_CTX_QUERY": \
+ ((x) == 0xfff6 ? "HWRM_NVM_GET_DEV_INFO": \
+ ((x) == 0x61 ? "HWRM_RING_GRP_FREE": \
+ ((x) == 0x60 ? "HWRM_RING_GRP_ALLOC": \
+ ((x) == 0x24 ? "HWRM_PORT_LPBK_QSTATS": \
+ ((x) == 0xf3 ? "HWRM_WOL_REASON_QCFG": \
+ ((x) == 0xa0 ? "HWRM_TUNNEL_DST_PORT_QUERY": \
+ ((x) == 0xa1 ? "HWRM_TUNNEL_DST_PORT_ALLOC": \
+ ((x) == 0xa2 ? "HWRM_TUNNEL_DST_PORT_FREE": \
+ ((x) == 0xfffc ? "HWRM_NVM_RAW_DUMP": \
+ ((x) == 0xfffb ? "HWRM_NVM_GET_DIR_INFO": \
+ ((x) == 0x10c ? "HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE": \
+ ((x) == 0x10b ? "HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC": \
+ ((x) == 0x10a ? "HWRM_CFA_VLAN_ANTISPOOF_QCFG": \
+ ((x) == 0xe ? "HWRM_FUNC_BUF_UNRGTR": \
+ ((x) == 0xf ? "HWRM_FUNC_VF_CFG": \
+ ((x) == 0xffff ? "HWRM_NVM_RAW_WRITE_BLK": \
+ ((x) == 0xfffe ? "HWRM_NVM_WRITE": \
+ ((x) == 0xfffd ? "HWRM_NVM_READ": \
+ ((x) == 0x50 ? "HWRM_RING_ALLOC": \
+ ((x) == 0x51 ? "HWRM_RING_FREE": \
+ ((x) == 0x52 ? "HWRM_RING_CMPL_RING_QAGGINT_PARAMS": \
+ ((x) == 0x53 ? "HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS": \
+ ((x) == 0x4a ? "HWRM_VNIC_QCAPS": \
+ ((x) == 0x49 ? "HWRM_VNIC_PLCMODES_QCFG": \
+ ((x) == 0x48 ? "HWRM_VNIC_PLCMODES_CFG": \
+ ((x) == 0x47 ? "HWRM_VNIC_RSS_QCFG": \
+ ((x) == 0x46 ? "HWRM_VNIC_RSS_CFG": \
+ ((x) == 0x44 ? "HWRM_VNIC_TPA_CFG": \
+ ((x) == 0x43 ? "HWRM_VNIC_QCFG": \
+ ((x) == 0x42 ? "HWRM_VNIC_CFG": \
+ ((x) == 0x41 ? "HWRM_VNIC_FREE": \
+ ((x) == 0x40 ? "HWRM_VNIC_ALLOC": \
+ ((x) == 0x0 ? "HWRM_VER_GET": \
+ ((x) == 0xfff9 ? "HWRM_NVM_FIND_DIR_ENTRY": \
+ ((x) == 0xfff8 ? "HWRM_NVM_MOD_DIR_ENTRY": \
+ ((x) == 0xfff7 ? "HWRM_NVM_ERASE_DIR_ENTRY": \
+ ((x) == 0x5e ? "HWRM_RING_RESET": \
+ ((x) == 0xfff5 ? "HWRM_NVM_VERIFY_UPDATE": \
+ ((x) == 0xfff4 ? "HWRM_NVM_MODIFY": \
+ ((x) == 0xfff3 ? "HWRM_NVM_INSTALL_UPDATE": \
+ ((x) == 0xfff2 ? "HWRM_NVM_SET_VARIABLE": \
+ ((x) == 0xfff1 ? "HWRM_NVM_GET_VARIABLE": \
+ ((x) == 0xfff0 ? "HWRM_NVM_FLUSH": \
+ ((x) == 0x2e ? "HWRM_PORT_LED_QCFG": \
+ ((x) == 0x2d ? "HWRM_PORT_LED_CFG": \
+ ((x) == 0x2f ? "HWRM_PORT_LED_QCAPS": \
+ ((x) == 0x2a ? "HWRM_PORT_PHY_QCAPS": \
+ ((x) == 0x38 ? "HWRM_QUEUE_PRI2COS_CFG": \
+ ((x) == 0x39 ? "HWRM_QUEUE_COS2BW_QCFG": \
+ ((x) == 0x32 ? "HWRM_QUEUE_CFG": \
+ ((x) == 0x33 ? "HWRM_FUNC_VLAN_CFG": \
+ ((x) == 0x30 ? "HWRM_QUEUE_QPORTCFG": \
+ ((x) == 0x31 ? "HWRM_QUEUE_QCFG": \
+ ((x) == 0x36 ? "HWRM_QUEUE_PFCENABLE_CFG": \
+ ((x) == 0x37 ? "HWRM_QUEUE_PRI2COS_QCFG": \
+ ((x) == 0x34 ? "HWRM_FUNC_VLAN_QCFG": \
+ ((x) == 0x35 ? "HWRM_QUEUE_PFCENABLE_QCFG": \
+ ((x) == 0xff17 ? "HWRM_DBG_COREDUMP_LIST": \
+ ((x) == 0xff18 ? "HWRM_DBG_COREDUMP_INITIATE": \
+ ((x) == 0xff19 ? "HWRM_DBG_COREDUMP_RETRIEVE": \
+ ((x) == 0xf1 ? "HWRM_WOL_FILTER_FREE": \
+ ((x) == 0xf0 ? "HWRM_WOL_FILTER_ALLOC": \
+ ((x) == 0x27 ? "HWRM_PORT_PHY_QCFG": \
+ ((x) == 0xf2 ? "HWRM_WOL_FILTER_QCFG": \
+ ((x) == 0x21 ? "HWRM_PORT_MAC_CFG": \
+ ((x) == 0x20 ? "HWRM_PORT_PHY_CFG": \
+ ((x) == 0x23 ? "HWRM_PORT_QSTATS": \
+ ((x) == 0x28 ? "HWRM_PORT_MAC_QCFG": \
+ ((x) == 0xffef ? "HWRM_NVM_VALIDATE_OPTION": \
+ ((x) == 0x3a ? "HWRM_QUEUE_COS2BW_CFG": \
+ "Unknown req_type"))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))))
+
+/* Command numbering (8 bytes) */
+struct cmd_nums {
+ uint16_t req_type;
+ /*
+ * This version of the specification defines the commands listed
+ * in the table below. The following are general implementation
+ * requirements for these commands: # All commands listed below
+ * that are marked neither reserved nor experimental shall be
+ * implemented by the HWRM. # A HWRM client compliant to this
+ * specification should not use commands outside of the list
+ * below. # A HWRM client compliant to this specification should
+ * not use command numbers marked reserved below. # A command
+ * marked experimental below may not be implemented by the HWRM.
+ * # A command marked experimental may change in the future
+ * version of the HWRM specification. # A command not listed
+ * below may be implemented by the HWRM. The behavior of
+ * commands that are not listed below is outside the scope of
+ * this specification.
+ */
+ #define HWRM_VER_GET (0x0UL)
+ #define HWRM_FUNC_BUF_UNRGTR (0xeUL)
+ #define HWRM_FUNC_VF_CFG (0xfUL)
+ /* Reserved for future use */
+ #define HWRM_RESERVED1 (0x10UL)
+ #define HWRM_FUNC_RESET (0x11UL)
+ #define HWRM_FUNC_GETFID (0x12UL)
+ #define HWRM_FUNC_VF_ALLOC (0x13UL)
+ #define HWRM_FUNC_VF_FREE (0x14UL)
+ #define HWRM_FUNC_QCAPS (0x15UL)
+ #define HWRM_FUNC_QCFG (0x16UL)
+ #define HWRM_FUNC_CFG (0x17UL)
+ #define HWRM_FUNC_QSTATS (0x18UL)
+ #define HWRM_FUNC_CLR_STATS (0x19UL)
+ #define HWRM_FUNC_DRV_UNRGTR (0x1aUL)
+ #define HWRM_FUNC_VF_RESC_FREE (0x1bUL)
+ #define HWRM_FUNC_VF_VNIC_IDS_QUERY (0x1cUL)
+ #define HWRM_FUNC_DRV_RGTR (0x1dUL)
+ #define HWRM_FUNC_DRV_QVER (0x1eUL)
+ #define HWRM_FUNC_BUF_RGTR (0x1fUL)
+ #define HWRM_PORT_PHY_CFG (0x20UL)
+ #define HWRM_PORT_MAC_CFG (0x21UL)
+ #define HWRM_PORT_QSTATS (0x23UL)
+ #define HWRM_PORT_LPBK_QSTATS (0x24UL)
+ #define HWRM_PORT_CLR_STATS (0x25UL)
+ #define HWRM_PORT_PHY_QCFG (0x27UL)
+ #define HWRM_PORT_MAC_QCFG (0x28UL)
+ #define HWRM_PORT_PHY_QCAPS (0x2aUL)
+ #define HWRM_PORT_LED_CFG (0x2dUL)
+ #define HWRM_PORT_LED_QCFG (0x2eUL)
+ #define HWRM_PORT_LED_QCAPS (0x2fUL)
+ #define HWRM_QUEUE_QPORTCFG (0x30UL)
+ #define HWRM_QUEUE_QCFG (0x31UL)
+ #define HWRM_QUEUE_CFG (0x32UL)
+ /* Experimental */
+ #define HWRM_FUNC_VLAN_CFG (0x33UL)
+ /* Experimental */
+ #define HWRM_FUNC_VLAN_QCFG (0x34UL)
+ #define HWRM_QUEUE_PFCENABLE_QCFG (0x35UL)
+ #define HWRM_QUEUE_PFCENABLE_CFG (0x36UL)
+ #define HWRM_QUEUE_PRI2COS_QCFG (0x37UL)
+ #define HWRM_QUEUE_PRI2COS_CFG (0x38UL)
+ #define HWRM_QUEUE_COS2BW_QCFG (0x39UL)
+ #define HWRM_QUEUE_COS2BW_CFG (0x3aUL)
+ #define HWRM_VNIC_ALLOC (0x40UL)
+ #define HWRM_VNIC_FREE (0x41UL)
+ #define HWRM_VNIC_CFG (0x42UL)
+ #define HWRM_VNIC_QCFG (0x43UL)
+ #define HWRM_VNIC_TPA_CFG (0x44UL)
+ #define HWRM_VNIC_RSS_CFG (0x46UL)
+ #define HWRM_VNIC_RSS_QCFG (0x47UL)
+ #define HWRM_VNIC_PLCMODES_CFG (0x48UL)
+ #define HWRM_VNIC_PLCMODES_QCFG (0x49UL)
+ #define HWRM_VNIC_QCAPS (0x4aUL)
+ #define HWRM_RING_ALLOC (0x50UL)
+ #define HWRM_RING_FREE (0x51UL)
+ #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS (0x52UL)
+ #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS (0x53UL)
+ #define HWRM_RING_RESET (0x5eUL)
+ #define HWRM_RING_GRP_ALLOC (0x60UL)
+ #define HWRM_RING_GRP_FREE (0x61UL)
+ #define HWRM_VNIC_RSS_COS_LB_CTX_ALLOC (0x70UL)
+ #define HWRM_VNIC_RSS_COS_LB_CTX_FREE (0x71UL)
+ #define HWRM_CFA_L2_FILTER_ALLOC (0x90UL)
+ #define HWRM_CFA_L2_FILTER_FREE (0x91UL)
+ #define HWRM_CFA_L2_FILTER_CFG (0x92UL)
+ #define HWRM_CFA_L2_SET_RX_MASK (0x93UL)
+ /* Experimental */
+ #define HWRM_CFA_VLAN_ANTISPOOF_CFG (0x94UL)
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC (0x95UL)
+ #define HWRM_CFA_TUNNEL_FILTER_FREE (0x96UL)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC (0x99UL)
+ #define HWRM_CFA_NTUPLE_FILTER_FREE (0x9aUL)
+ #define HWRM_CFA_NTUPLE_FILTER_CFG (0x9bUL)
+ #define HWRM_CFA_EM_FLOW_ALLOC (0x9cUL)
+ #define HWRM_CFA_EM_FLOW_FREE (0x9dUL)
+ #define HWRM_TUNNEL_DST_PORT_QUERY (0xa0UL)
+ #define HWRM_TUNNEL_DST_PORT_ALLOC (0xa1UL)
+ #define HWRM_TUNNEL_DST_PORT_FREE (0xa2UL)
+ #define HWRM_STAT_CTX_ALLOC (0xb0UL)
+ #define HWRM_STAT_CTX_FREE (0xb1UL)
+ #define HWRM_STAT_CTX_QUERY (0xb2UL)
+ #define HWRM_STAT_CTX_CLR_STATS (0xb3UL)
+ #define HWRM_FW_RESET (0xc0UL)
+ #define HWRM_FW_QSTATUS (0xc1UL)
+ #define HWRM_EXEC_FWD_RESP (0xd0UL)
+ #define HWRM_REJECT_FWD_RESP (0xd1UL)
+ #define HWRM_REJECT_FWD_OUTPUT (0xd1UL)
+ #define HWRM_FWD_OUTPUT (0xd2UL)
+ #define HWRM_FWD_ASYNC_EVENT_CMPL (0xd3UL)
+ #define HWRM_TEMP_MONITOR_QUERY (0xe0UL)
+ #define HWRM_WOL_FILTER_ALLOC (0xf0UL)
+ #define HWRM_WOL_FILTER_FREE (0xf1UL)
+ #define HWRM_WOL_FILTER_QCFG (0xf2UL)
+ #define HWRM_WOL_REASON_QCFG (0xf3UL)
+ /* Experimental */
+ #define HWRM_CFA_VLAN_ANTISPOOF_QCFG (0x10aUL)
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC (0x10bUL)
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE (0x10cUL)
+ /* Experimental */
+ #define HWRM_DBG_COREDUMP_LIST (0xff17UL)
+ /* Experimental */
+ #define HWRM_DBG_COREDUMP_INITIATE (0xff18UL)
+ /* Experimental */
+ #define HWRM_DBG_COREDUMP_RETRIEVE (0xff19UL)
+ #define HWRM_NVM_VALIDATE_OPTION (0xffefUL)
+ #define HWRM_NVM_FLUSH (0xfff0UL)
+ #define HWRM_NVM_GET_VARIABLE (0xfff1UL)
+ #define HWRM_NVM_SET_VARIABLE (0xfff2UL)
+ #define HWRM_NVM_INSTALL_UPDATE (0xfff3UL)
+ #define HWRM_NVM_MODIFY (0xfff4UL)
+ #define HWRM_NVM_VERIFY_UPDATE (0xfff5UL)
+ #define HWRM_NVM_GET_DEV_INFO (0xfff6UL)
+ #define HWRM_NVM_ERASE_DIR_ENTRY (0xfff7UL)
+ #define HWRM_NVM_MOD_DIR_ENTRY (0xfff8UL)
+ #define HWRM_NVM_FIND_DIR_ENTRY (0xfff9UL)
+ #define HWRM_NVM_GET_DIR_ENTRIES (0xfffaUL)
+ #define HWRM_NVM_GET_DIR_INFO (0xfffbUL)
+ #define HWRM_NVM_RAW_DUMP (0xfffcUL)
+ #define HWRM_NVM_READ (0xfffdUL)
+ #define HWRM_NVM_WRITE (0xfffeUL)
+ #define HWRM_NVM_RAW_WRITE_BLK (0xffffUL)
+ uint16_t unused_0[3];
} __attribute__((packed));
-#define HWRM_GET_HWRM_ERROR_CODE(arg) \
- { \
- typeof(arg) x = (arg); \
- ((x) == 0xf ? "HWRM_ERROR" : \
- ((x) == 0xffff ? "CMD_NOT_SUPPORTED" : \
- ((x) == 0xfffe ? "UNKNOWN_ERR" : \
- ((x) == 0x4 ? "RESOURCE_ALLOC_ERROR" : \
- ((x) == 0x5 ? "INVALID_FLAGS" : \
- ((x) == 0x6 ? "INVALID_ENABLES" : \
- ((x) == 0x0 ? "SUCCESS" : \
- ((x) == 0x1 ? "FAIL" : \
- ((x) == 0x2 ? "INVALID_PARAMS" : \
- ((x) == 0x3 ? "RESOURCE_ACCESS_DENIED" : \
- "Unknown error_code")))))))))) \
- }
-
-/* Return Codes (8 bytes) */
+#define HWRM_GET_HWRM_ERROR_CODE(x) \
+ ((x) == 0xf ? "HWRM_ERROR": \
+ ((x) == 0xffff ? "CMD_NOT_SUPPORTED": \
+ ((x) == 0xfffe ? "UNKNOWN_ERR": \
+ ((x) == 0x4 ? "RESOURCE_ALLOC_ERROR": \
+ ((x) == 0x5 ? "INVALID_FLAGS": \
+ ((x) == 0x6 ? "INVALID_ENABLES": \
+ ((x) == 0x0 ? "SUCCESS": \
+ ((x) == 0x1 ? "FAIL": \
+ ((x) == 0x2 ? "INVALID_PARAMS": \
+ ((x) == 0x3 ? "RESOURCE_ACCESS_DENIED": \
+ "Unknown error_code"))))))))))
+
+/* Return Codes (8 bytes) */
struct ret_codes {
uint16_t error_code;
/* These are numbers assigned to return/error codes. */
/* Request was successfully executed by the HWRM. */
- #define HWRM_ERR_CODE_SUCCESS (UINT32_C(0x0))
+ #define HWRM_ERR_CODE_SUCCESS (0x0UL)
/* THe HWRM failed to execute the request. */
- #define HWRM_ERR_CODE_FAIL (UINT32_C(0x1))
+ #define HWRM_ERR_CODE_FAIL (0x1UL)
/*
* The request contains invalid argument(s) or
* input parameters.
*/
- #define HWRM_ERR_CODE_INVALID_PARAMS (UINT32_C(0x2))
+ #define HWRM_ERR_CODE_INVALID_PARAMS (0x2UL)
/*
* The requester is not allowed to access the
* requested resource. This error code shall be
@@ -11556,33 +28930,33 @@ struct ret_codes {
* or modify an existing resource that is not
* accessible by the requester.
*/
- #define HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED (UINT32_C(0x3))
+ #define HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED (0x3UL)
/*
* The HWRM is unable to allocate the requested
* resource. This code only applies to requests
* for HWRM resource allocations.
*/
- #define HWRM_ERR_CODE_RESOURCE_ALLOC_ERROR (UINT32_C(0x4))
+ #define HWRM_ERR_CODE_RESOURCE_ALLOC_ERROR (0x4UL)
/* Invalid combination of flags is specified in the request. */
- #define HWRM_ERR_CODE_INVALID_FLAGS (UINT32_C(0x5))
+ #define HWRM_ERR_CODE_INVALID_FLAGS (0x5UL)
/*
* Invalid combination of enables fields is
* specified in the request.
*/
- #define HWRM_ERR_CODE_INVALID_ENABLES (UINT32_C(0x6))
+ #define HWRM_ERR_CODE_INVALID_ENABLES (0x6UL)
/*
* Generic HWRM execution error that represents
* an internal error.
*/
- #define HWRM_ERR_CODE_HWRM_ERROR (UINT32_C(0xf))
+ #define HWRM_ERR_CODE_HWRM_ERROR (0xfUL)
/* Unknown error */
- #define HWRM_ERR_CODE_UNKNOWN_ERR (UINT32_C(0xfffe))
+ #define HWRM_ERR_CODE_UNKNOWN_ERR (0xfffeUL)
/* Unsupported or invalid command */
- #define HWRM_ERR_CODE_CMD_NOT_SUPPORTED (UINT32_C(0xffff))
+ #define HWRM_ERR_CODE_CMD_NOT_SUPPORTED (0xffffUL)
uint16_t unused_0[3];
} __attribute__((packed));
-/* Output (16 bytes) */
+/* Output (16 bytes) */
struct hwrm_err_output {
uint16_t error_code;
/*
@@ -11619,7 +28993,7 @@ struct hwrm_err_output {
*/
} __attribute__((packed));
-/* Port Tx Statistics Formats (408 bytes) */
+/* Port Tx Statistics Formats (408 bytes) */
struct tx_port_stats {
uint64_t tx_64b_frames;
/* Total Number of 64 Bytes frames transmitted */
@@ -11635,9 +29009,9 @@ struct tx_port_stats {
/* Total Number of 1024-1518 Bytes frames transmitted */
uint64_t tx_good_vlan_frames;
/*
- * Total Number of each good VLAN (exludes FCS errors) frame
+ * Total Number of each good VLAN (exludes FCS errors) frame
* transmitted which is 1519 to 1522 bytes in length inclusive
- * (excluding framing bits but including FCS bytes).
+ * (excluding framing bits but including FCS bytes).
*/
uint64_t tx_1519b_2047_frames;
/* Total Number of 1519-2047 Bytes frames transmitted */
@@ -11739,7 +29113,7 @@ struct tx_port_stats {
/* EEE LPI Duration Counter on TX */
uint64_t tx_llfc_logical_msgs;
/*
- * Total number of Link Level Flow Control (LLFC) messages
+ * Total number of Link Level Flow Control (LLFC) messages
* transmitted
*/
uint64_t tx_hcfc_msgs;
@@ -11756,7 +29130,7 @@ struct tx_port_stats {
/* Total Tx Error Drops per Port reported by STATS block */
} __attribute__((packed));
-/* Port Rx Statistics Formats (528 bytes) */
+/* Port Rx Statistics Formats (528 bytes) */
struct rx_port_stats {
uint64_t rx_64b_frames;
/* Total Number of 64 Bytes frames received */
@@ -11772,9 +29146,9 @@ struct rx_port_stats {
/* Total Number of 1024-1518 Bytes frames received */
uint64_t rx_good_vlan_frames;
/*
- * Total Number of each good VLAN (exludes FCS errors) frame
+ * Total Number of each good VLAN (exludes FCS errors) frame
* received which is 1519 to 1522 bytes in length inclusive
- * (excluding framing bits but including FCS bytes).
+ * (excluding framing bits but including FCS bytes).
*/
uint64_t rx_1519b_2047b_frames;
/* Total Number of 1519-2047 Bytes frames received */
@@ -11841,7 +29215,7 @@ struct rx_port_stats {
uint64_t rx_trunc_frames;
/* Total number of truncated frames received */
uint64_t rx_good_frames;
- /* Total number of good frames (without errors) received */
+ /* Total number of good frames (without errors) received */
uint64_t rx_pfc_xon2xoff_frames_pri0;
/*
* Total number of received PFC frames with transition from XON
@@ -11934,17 +29308,17 @@ struct rx_port_stats {
/* EEE LPI Duration Counter on RX */
uint64_t rx_llfc_physical_msgs;
/*
- * Total number of physical type Link Level Flow Control (LLFC)
+ * Total number of physical type Link Level Flow Control (LLFC)
* messages received
*/
uint64_t rx_llfc_logical_msgs;
/*
- * Total number of logical type Link Level Flow Control (LLFC)
+ * Total number of logical type Link Level Flow Control (LLFC)
* messages received
*/
uint64_t rx_llfc_msgs_with_crc_err;
/*
- * Total number of logical type Link Level Flow Control (LLFC)
+ * Total number of logical type Link Level Flow Control (LLFC)
* messages received with CRC error
*/
uint64_t rx_hcfc_msgs;
@@ -11963,34 +29337,563 @@ struct rx_port_stats {
/* Total Rx Error Drops per Port reported by STATS block */
} __attribute__((packed));
-/* Periodic Statistics Context DMA to host (160 bytes) */
-/*
- * per-context HW statistics -- chip view
- */
+/* VXLAN IPv4 encapsulation structure (16 bytes) */
+struct hwrm_vxlan_ipv4_hdr {
+ uint8_t ver_hlen;
+ /* IPv4 version and header length. */
+ /* IPv4 header length */
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_HEADER_LENGTH_MASK 0xfUL
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_HEADER_LENGTH_SFT 0
+ /* Version */
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_VERSION_MASK 0xf0UL
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_VERSION_SFT 4
+ uint8_t tos;
+ /* IPv4 type of service. */
+ uint16_t ip_id;
+ /* IPv4 identification. */
+ uint16_t flags_frag_offset;
+ /* IPv4 flags and offset. */
+ uint8_t ttl;
+ /* IPv4 TTL. */
+ uint8_t protocol;
+ /* IPv4 protocol. */
+ uint32_t src_ip_addr;
+ /* IPv4 source address. */
+ uint32_t dest_ip_addr;
+ /* IPv4 destination address. */
+} __attribute__((packed));
+/* VXLAN IPv6 encapsulation structure (32 bytes) */
+struct hwrm_vxlan_ipv6_hdr {
+ uint32_t ver_tc_flow_label;
+ /* IPv6 version, traffic class and flow label. */
+ /* IPv6 version shift */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_VER_SFT 0x1cUL
+ /* IPv6 version mask */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_VER_MASK 0xf0000000UL
+ /* IPv6 TC shift */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_TC_SFT 0x14UL
+ /* IPv6 TC mask */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_TC_MASK 0xff00000UL
+ /* IPv6 flow label shift */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_SFT 0x0UL
+ /* IPv6 flow label mask */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_MASK 0xfffffUL
+ uint16_t payload_len;
+ /* IPv6 payload length. */
+ uint8_t next_hdr;
+ /* IPv6 next header. */
+ uint8_t ttl;
+ /* IPv6 TTL. */
+ uint32_t src_ip_addr[4];
+ /* IPv6 source address. */
+ uint32_t dest_ip_addr[4];
+ /* IPv6 destination address. */
+} __attribute__((packed));
+
+/* VXLAN encapsulation structure (72 bytes) */
+struct hwrm_cfa_encap_data_vxlan {
+ uint8_t src_mac_addr[6];
+ /* Source MAC address. */
+ uint16_t unused_0;
+ /* reserved. */
+ uint8_t dst_mac_addr[6];
+ /* Destination MAC address. */
+ uint8_t num_vlan_tags;
+ /* Number of VLAN tags. */
+ uint8_t unused_1;
+ /* reserved. */
+ uint16_t ovlan_tpid;
+ /* Outer VLAN TPID. */
+ uint16_t ovlan_tci;
+ /* Outer VLAN TCI. */
+ uint16_t ivlan_tpid;
+ /* Inner VLAN TPID. */
+ uint16_t ivlan_tci;
+ /* Inner VLAN TCI. */
+ uint32_t l3[10];
+ /* L3 header fields. */
+ /* IP version mask. */
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_MASK 0xfUL
+ /* IP version 4. */
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV4 0x4UL
+ /* IP version 6. */
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV6 0x6UL
+ uint16_t src_port;
+ /* UDP source port. */
+ uint16_t dst_port;
+ /* UDP destination port. */
+ uint32_t vni;
+ /* VXLAN Network Identifier. */
+} __attribute__((packed));
+
+/* Periodic Statistics Context DMA to host (160 bytes) */
struct ctx_hw_stats64 {
uint64_t rx_ucast_pkts;
+ /* Number of received unicast packets */
uint64_t rx_mcast_pkts;
+ /* Number of received multicast packets */
uint64_t rx_bcast_pkts;
+ /* Number of received broadcast packets */
+ uint64_t rx_err_pkts;
+ /* Number of discarded packets on received path */
uint64_t rx_drop_pkts;
- uint64_t rx_discard_pkts;
+ /* Number of dropped packets on received path */
uint64_t rx_ucast_bytes;
+ /* Number of received bytes for unicast traffic */
uint64_t rx_mcast_bytes;
+ /* Number of received bytes for multicast traffic */
uint64_t rx_bcast_bytes;
-
+ /* Number of received bytes for broadcast traffic */
uint64_t tx_ucast_pkts;
+ /* Number of transmitted unicast packets */
uint64_t tx_mcast_pkts;
+ /* Number of transmitted multicast packets */
uint64_t tx_bcast_pkts;
+ /* Number of transmitted broadcast packets */
+ uint64_t tx_err_pkts;
+ /* Number of discarded packets on transmit path */
uint64_t tx_drop_pkts;
- uint64_t tx_discard_pkts;
+ /* Number of dropped packets on transmit path */
uint64_t tx_ucast_bytes;
+ /* Number of transmitted bytes for unicast traffic */
uint64_t tx_mcast_bytes;
+ /* Number of transmitted bytes for multicast traffic */
uint64_t tx_bcast_bytes;
-
+ /* Number of transmitted bytes for broadcast traffic */
uint64_t tpa_pkts;
+ /* Number of TPA packets */
uint64_t tpa_bytes;
+ /* Number of TPA bytes */
uint64_t tpa_events;
+ /* Number of TPA events */
uint64_t tpa_aborts;
+ /* Number of TPA aborts */
+} __attribute__((packed));
+
+/* Structure data header (16 bytes) */
+struct hwrm_struct_hdr {
+ uint16_t struct_id;
+ /* This value indicates the structured data ID. */
+ /* LLDP configuration structured data ID. */
+ #define HWRM_STRUCT_HDR_STRUCT_ID_LLDP_CFG 0x41bUL
+ /* DCBX ETS configuration structured data ID. */
+ #define HWRM_STRUCT_HDR_STRUCT_ID_DCBX_ETS 0x41dUL
+ /* DCBX PFC configuration structured data ID. */
+ #define HWRM_STRUCT_HDR_STRUCT_ID_DCBX_PFC 0x41fUL
+ /* DCBX APP configuration structured data ID. */
+ #define HWRM_STRUCT_HDR_STRUCT_ID_DCBX_APP 0x421UL
+ /*
+ * DCBX state configuration structured data ID
+ * for all DCBX features.
+ */
+ #define HWRM_STRUCT_HDR_STRUCT_ID_DCBX_FEATURE_STATE 0x422UL
+ /*
+ * LLDP generic structured data ID. This is used
+ * with GET_STRUCTURED_DATA only.
+ */
+ #define HWRM_STRUCT_HDR_STRUCT_ID_LLDP_GENERIC 0x424UL
+ /*
+ * LLDP device structured data ID. This is used
+ * with GET_STRUCTURED_DATA only.
+ */
+ #define HWRM_STRUCT_HDR_STRUCT_ID_LLDP_DEVICE 0x426UL
+ /* reserved for AFM usage. */
+ #define HWRM_STRUCT_HDR_STRUCT_ID_AFM_OPAQUE 0x1UL
+ /* Port description. */
+ #define HWRM_STRUCT_HDR_STRUCT_ID_PORT_DESCRIPTION 0xaUL
+ /* RSSv2 Configuration. */
+ #define HWRM_STRUCT_HDR_STRUCT_ID_RSS_V2 0x64UL
+ uint16_t len;
+ /* This value indicates the length of structured data. */
+ uint8_t version;
+ /* This value indicates the version of structured data. */
+ uint8_t count;
+ /* This value indicates the number of structured data elements. */
+ uint16_t subtype;
+ /* This value indicates the subtype. */
+ uint16_t next_offset;
+ /*
+ * This value indicates the count of 64-bit values that point to
+ * the next header. A value of 0 means that this is the last
+ * element. The value is a count of 64-bit words from the
+ * beginning of the current header.
+ */
+ /* This value indicates this is the last element */
+ #define HWRM_STRUCT_HDR_NEXT_OFFSET_LAST 0x0UL
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* DCBX ETS configuration structure (1053) (32 bytes) */
+struct hwrm_struct_data_dcbx_ets {
+ uint8_t destination;
+ /*
+ * This field indicates if this configuration is ETS
+ * recommendation or ETS configuration. A value 1 means it is
+ * ETS configuration, A value of 2 means it is a ETS
+ * recommendation.
+ */
+ /* ETS configuration */
+ #define HWRM_STRUCT_DATA_DCBX_ETS_DESTINATION_CONFIGURATION 0x1UL
+ /* ETS recommendation */
+ #define HWRM_STRUCT_DATA_DCBX_ETS_DESTINATION_RECOMMMENDATION 0x2UL
+ uint8_t max_tcs;
+ /* This value indicates maximum ETS TCs supported. */
+ uint16_t unused_0;
+ /* unused. */
+ uint8_t pri0_to_tc_map;
+ /* ETS priority 0 to TC map. */
+ uint8_t pri1_to_tc_map;
+ /* ETS priority 1 to TC map. */
+ uint8_t pri2_to_tc_map;
+ /* ETS priority 2 to TC map. */
+ uint8_t pri3_to_tc_map;
+ /* ETS priority 3 to TC map. */
+ uint8_t pri4_to_tc_map;
+ /* ETS priority 4 to TC map. */
+ uint8_t pri5_to_tc_map;
+ /* ETS priority 5 to TC map. */
+ uint8_t pri6_to_tc_map;
+ /* ETS priority 6 to TC map. */
+ uint8_t pri7_to_tc_map;
+ /* ETS priority 7 to TC map. */
+ uint8_t tc0_to_bw_map;
+ /* ETS TC 0 to bandwidth map. */
+ uint8_t tc1_to_bw_map;
+ /* ETS TC 1 to bandwidth map. */
+ uint8_t tc2_to_bw_map;
+ /* ETS TC 2 to bandwidth map. */
+ uint8_t tc3_to_bw_map;
+ /* ETS TC 3 to bandwidth map. */
+ uint8_t tc4_to_bw_map;
+ /* ETS TC 4 to bandwidth map. */
+ uint8_t tc5_to_bw_map;
+ /* ETS TC 5 to bandwidth map. */
+ uint8_t tc6_to_bw_map;
+ /* ETS TC 6 to bandwidth map. */
+ uint8_t tc7_to_bw_map;
+ /* ETS TC 7 to bandwidth map. */
+ uint8_t tc0_to_tsa_map;
+ /* ETS TC 0 to TSA map. */
+ /* strict priority */
+ #define HWRM_STRUCT_DATA_DCBX_ETS_TC0_TO_TSA_MAP_TSA_TYPE_SP 0x0UL
+ /* credit based shaper */
+ #define HWRM_STRUCT_DATA_DCBX_ETS_TC0_TO_TSA_MAP_TSA_TYPE_CBS 0x1UL
+ /* ETS */
+ #define HWRM_STRUCT_DATA_DCBX_ETS_TC0_TO_TSA_MAP_TSA_TYPE_ETS 0x2UL
+ /* vendor specific */
+ #define \
+ HWRM_STRUCT_DATA_DCBX_ETS_TC0_TO_TSA_MAP_TSA_TYPE_VENDOR_SPECIFIC 0xffUL
+ uint8_t tc1_to_tsa_map;
+ /* ETS TC 1 to TSA map. */
+ uint8_t tc2_to_tsa_map;
+ /* ETS TC 2 to TSA map. */
+ uint8_t tc3_to_tsa_map;
+ /* ETS TC 3 to TSA map. */
+ uint8_t tc4_to_tsa_map;
+ /* ETS TC 4 to TSA map. */
+ uint8_t tc5_to_tsa_map;
+ /* ETS TC 5 to TSA map. */
+ uint8_t tc6_to_tsa_map;
+ /* ETS TC 6 to TSA map. */
+ uint8_t tc7_to_tsa_map;
+ /* ETS TC 7 to TSA map. */
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* DCBX PFC configuration structure (1055) (8 bytes) */
+struct hwrm_struct_data_dcbx_pfc {
+ uint8_t pfc_priority_bitmap;
+ /*
+ * This field indicates PFC priority bit map. A value of '0'
+ * indicates PFC is disabled. A value of '1' indicates PFC is
+ * enabled on that priority.
+ */
+ uint8_t max_pfc_tcs;
+ /*
+ * This field indicates max PFC TCs supported. Each PFC TC will
+ * map to a lossless CoS queue.
+ */
+ uint8_t mbc;
+ /*
+ * This field indicates if MACSec bypass capability is enabled.
+ * A value of '1' indicates MBC is enabled. A value of '0'
+ * indicates MBC is disabled.
+ */
+ uint8_t unused_0[5];
+} __attribute__((packed));
+
+/* DCBX Application configuration structure (1057) (8 bytes) */
+struct hwrm_struct_data_dcbx_app {
+ uint16_t protocol_id;
+ /*
+ * This field indicates the protocol identifier. This should be
+ * specified in big endian format.
+ */
+ uint8_t protocol_selector;
+ /*
+ * This field indicates the protocol selector. The valid values
+ * are mentioned below.
+ */
+ /* ether type */
+ #define HWRM_STRUCT_DATA_DCBX_APP_PROTOCOL_SELECTOR_ETHER_TYPE 0x1UL
+ /* TCP port */
+ #define HWRM_STRUCT_DATA_DCBX_APP_PROTOCOL_SELECTOR_TCP_PORT 0x2UL
+ /* UDP port */
+ #define HWRM_STRUCT_DATA_DCBX_APP_PROTOCOL_SELECTOR_UDP_PORT 0x3UL
+ /* TCP & UDP port */
+ #define HWRM_STRUCT_DATA_DCBX_APP_PROTOCOL_SELECTOR_TCP_UDP_PORT 0x4UL
+ uint8_t priority;
+ /* This field indicates application priority. */
+ uint8_t valid;
+ /* This field indicates this entry is valid. */
+ uint8_t unused_0[3];
+} __attribute__((packed));
+
+/* DCBX feature states configuration structure (1058) (8 bytes) */
+struct hwrm_struct_data_dcbx_feature_state {
+ uint8_t dcbx_mode;
+ /* DCBX mode - IEEE or CEE. This is read only field. */
+ /* DCBX disabled mode. */
+ #define HWRM_STRUCT_DATA_DCBX_FEATURE_STATE_DCBX_MODE_DCBX_DISABLED \
+ 0x0UL
+ /* DCBX IEEE mode. */
+ #define HWRM_STRUCT_DATA_DCBX_FEATURE_STATE_DCBX_MODE_DCBX_IEEE 0x1UL
+ /* DCBX CEE mode. */
+ #define HWRM_STRUCT_DATA_DCBX_FEATURE_STATE_DCBX_MODE_DCBX_CEE 0x2UL
+ uint8_t ets_state;
+ /* ETS TLV state. */
+ uint8_t pfc_state;
+ /* PFC TLV state. */
+ uint8_t app_state;
+ /* App TLV state. */
+ /* Feature enable bit position. */
+ #define HWRM_STRUCT_DATA_DCBX_FEATURE_STATE_APP_STATE_ENABLE_BIT_POS \
+ 0x7UL
+ /* Feature willing bit position. */
+ #define HWRM_STRUCT_DATA_DCBX_FEATURE_STATE_APP_STATE_WILLING_BIT_POS \
+ 0x6UL
+ /* Feature advertise bit position. */
+ #define \
+ HWRM_STRUCT_DATA_DCBX_FEATURE_STATE_APP_STATE_ADVERTISE_BIT_POS 0x5UL
+ uint8_t unused_0[3];
+ /* unused. */
+ uint8_t resets;
+ /*
+ * This field is used to reset the DCBX configuration to factory
+ * defaults.
+ */
+ /* reset ETS configuration. */
+ #define HWRM_STRUCT_DATA_DCBX_FEATURE_STATE_RESETS_RESET_ETS 0x1UL
+ /* reset PFC configuration. */
+ #define HWRM_STRUCT_DATA_DCBX_FEATURE_STATE_RESETS_RESET_PFC 0x2UL
+ /* reset application configuration. */
+ #define HWRM_STRUCT_DATA_DCBX_FEATURE_STATE_RESETS_RESET_APP 0x4UL
+ /* reset DCBX state configuration. */
+ #define HWRM_STRUCT_DATA_DCBX_FEATURE_STATE_RESETS_RESET_STATE 0x8UL
+} __attribute__((packed));
+
+/* LLDP TLVs transmit configuration structure (1051) (8 bytes) */
+struct hwrm_struct_data_lldp {
+ uint8_t admin_state;
+ /* Port admin state */
+ /* Disable both Tx and Rx */
+ #define HWRM_STRUCT_DATA_LLDP_ADMIN_STATE_DISABLE 0x0UL
+ /* Enable Tx only */
+ #define HWRM_STRUCT_DATA_LLDP_ADMIN_STATE_TX 0x1UL
+ /* Enable Rx only */
+ #define HWRM_STRUCT_DATA_LLDP_ADMIN_STATE_RX 0x2UL
+ /* Enable both Tx and Rx */
+ #define HWRM_STRUCT_DATA_LLDP_ADMIN_STATE_ENABLE 0x3UL
+ uint8_t port_description_state;
+ /* Port desciption TLV transmit state (enable(1)/disable(0)). */
+ /* Disable */
+ #define HWRM_STRUCT_DATA_LLDP_PORT_DESCRIPTION_STATE_DISABLE 0x0UL
+ /* Enable */
+ #define HWRM_STRUCT_DATA_LLDP_PORT_DESCRIPTION_STATE_ENABLE 0x1UL
+ uint8_t system_name_state;
+ /* System name TLV transmit state (enable(1)/disable(0)). */
+ /* Disable */
+ #define HWRM_STRUCT_DATA_LLDP_SYSTEM_NAME_STATE_DISABLE 0x0UL
+ /* Enable */
+ #define HWRM_STRUCT_DATA_LLDP_SYSTEM_NAME_STATE_ENABLE 0x1UL
+ uint8_t system_desc_state;
+ /* System desciption TLV transmit state (enable(1)/disable(0)). */
+ /* Disable */
+ #define HWRM_STRUCT_DATA_LLDP_SYSTEM_DESC_STATE_DISABLE 0x0UL
+ /* Enable */
+ #define HWRM_STRUCT_DATA_LLDP_SYSTEM_DESC_STATE_ENABLE 0x1UL
+ uint8_t system_cap_state;
+ /* System capabilities TLV transmit state (enable(1)/disable(0)). */
+ /* Disable */
+ #define HWRM_STRUCT_DATA_LLDP_SYSTEM_CAP_STATE_DISABLE 0x0UL
+ /* Enable */
+ #define HWRM_STRUCT_DATA_LLDP_SYSTEM_CAP_STATE_ENABLE 0x1UL
+ uint8_t mgmt_addr_state;
+ /* Management address TLV transmit state (enable(1)/disable(0)). */
+ /* Disable */
+ #define HWRM_STRUCT_DATA_LLDP_MGMT_ADDR_STATE_DISABLE 0x0UL
+ /* Enable */
+ #define HWRM_STRUCT_DATA_LLDP_MGMT_ADDR_STATE_ENABLE 0x1UL
+ uint8_t async_event_notification_state;
+ /* Async event notification state (enable(1)/disable(0)). */
+ /* Disable */
+ #define HWRM_STRUCT_DATA_LLDP_ASYNC_EVENT_NOTIFICATION_STATE_DISABLE \
+ 0x0UL
+ /* Enable */
+ #define HWRM_STRUCT_DATA_LLDP_ASYNC_EVENT_NOTIFICATION_STATE_ENABLE \
+ 0x1UL
+ uint8_t unused_0;
+} __attribute__((packed));
+
+/* LLDP generic TLV configuration (1060) (16 bytes) */
+struct hwrm_struct_data_lldp_generic {
+ uint8_t tlv_type;
+ /* TLV type. */
+ /* Chassis ID TLV */
+ #define HWRM_STRUCT_DATA_LLDP_GENERIC_TLV_TYPE_CHASSIS 0x1UL
+ /* Port ID TLV */
+ #define HWRM_STRUCT_DATA_LLDP_GENERIC_TLV_TYPE_PORT 0x2UL
+ /* System name TLV */
+ #define HWRM_STRUCT_DATA_LLDP_GENERIC_TLV_TYPE_SYSTEM_NAME 0x3UL
+ /* System description TLV */
+ #define HWRM_STRUCT_DATA_LLDP_GENERIC_TLV_TYPE_SYSTEM_DESCRIPTION 0x4UL
+ /* Port name TLV */
+ #define HWRM_STRUCT_DATA_LLDP_GENERIC_TLV_TYPE_PORT_NAME 0x5UL
+ /* Port description TLV */
+ #define HWRM_STRUCT_DATA_LLDP_GENERIC_TLV_TYPE_PORT_DESCRIPTION 0x6UL
+ uint8_t subtype;
+ /* TLV sub-type. */
+ uint8_t length;
+ /* Length. */
+ uint8_t unused_0;
+ /* unused. */
+ uint32_t unused_1;
+ uint32_t tlv_value[64];
+ /* TLV value. */
+} __attribute__((packed));
+
+/* LLDP device TLV configuration (1062) (64 bytes) */
+struct hwrm_struct_data_lldp_device {
+ uint16_t ttl;
+ /* Time to Live. */
+ uint8_t mgmt_addr_len;
+ /* Management address length. */
+ uint8_t mgmt_addr_type;
+ /* Management address type. */
+ uint32_t unused_0;
+ uint32_t mgmt_addr[8];
+ /* Management address. */
+ uint32_t system_caps;
+ /* System capabilities. */
+ uint8_t intf_num_type;
+ /* Interface number type. */
+ uint8_t mgmt_addr_oid_length;
+ /* Management address OID length. */
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint32_t intf_num;
+ /* Interface number. */
+ uint32_t unused_3;
+ uint32_t mgmt_addr_oid[32];
+ /* Management address OID. */
+} __attribute__((packed));
+
+/* port description (10) (8 bytes) */
+struct hwrm_struct_data_port_description {
+ uint8_t port_id;
+ /*
+ * Port #. Port number starts at 0 and anything greater than
+ * number of ports minus 1 is an error.
+ */
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* RSSv2 Configuration (100) (16 bytes) */
+struct hwrm_struct_data_rss_v2 {
+ uint16_t flags;
+ /* When this bit is '1', the hash type and hash key are included. */
+ #define HWRM_STRUCT_DATA_RSS_V2_FLAGS_HASH_VALID 0x1UL
+ uint16_t rss_ctx_id;
+ /* RSS Context index. */
+ uint16_t num_ring_groups;
+ /* Number ring group IDs. */
+ uint16_t hash_type;
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source and destination IPv4 addresses of IPv4 packets.
+ */
+ #define HWRM_STRUCT_DATA_RSS_V2_HASH_TYPE_IPV4 0x1UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination
+ * ports of TCP/IPv4 packets.
+ */
+ #define HWRM_STRUCT_DATA_RSS_V2_HASH_TYPE_TCP_IPV4 0x2UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination
+ * ports of UDP/IPv4 packets.
+ */
+ #define HWRM_STRUCT_DATA_RSS_V2_HASH_TYPE_UDP_IPV4 0x4UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source and destination IPv4 addresses of IPv6 packets.
+ */
+ #define HWRM_STRUCT_DATA_RSS_V2_HASH_TYPE_IPV6 0x8UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination
+ * ports of TCP/IPv6 packets.
+ */
+ #define HWRM_STRUCT_DATA_RSS_V2_HASH_TYPE_TCP_IPV6 0x10UL
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination
+ * ports of UDP/IPv6 packets.
+ */
+ #define HWRM_STRUCT_DATA_RSS_V2_HASH_TYPE_UDP_IPV6 0x20UL
+ uint64_t hash_key_ring_group_ids;
+ /*
+ * Variable size data. Hash key (optional) followed by
+ * ring_group_ids.
+ */
+} __attribute__((packed));
+
+/* Coredump segment query record (16 bytes) */
+struct coredump_segment_record {
+ uint16_t component_id;
+ /* Component id of the returned component. */
+ uint16_t segment_id;
+ /* Segment id of the returned component. */
+ uint16_t max_instances;
+ /* Not used. */
+ uint8_t version_hi;
+ /* Major version. */
+ uint8_t version_low;
+ /* Minor version. */
+ uint8_t seg_flags;
+ /* bit 0: live data bit 1: crashed data */
+ uint8_t unused_0[7];
+ /* Not used. */
+} __attribute__((packed));
+
+/* Coredump register block header (16 bytes) */
+struct coredump_data_hdr {
+ uint32_t address;
+ /* Starting address of the register range. */
+ uint32_t flags_length;
+ /*
+ * length: 0 - 23 bits represents the actual data without the
+ * pad. flags: 24 - 31 bits represents indirect register ranges.
+ */
+ uint32_t instance;
+ /*
+ * Value in the partner register for indirect or multi-field
+ * registers.
+ */
+ uint32_t next_offset;
+ /* Offset to the next header within a segment. */
} __attribute__((packed));
-#endif /* _HSI_STRUCT_DEF_DPDK_ */
+#endif /* _HSI_STRUCT_DEF_DPDK_H_ */
--
2.13.5 (Apple Git-94)
^ permalink raw reply [flat|nested] 24+ messages in thread