DPDK patches and discussions
 help / color / mirror / Atom feed
* [dpdk-dev] [PATCH] doc: update flow filting document
@ 2018-01-30  7:32 Wei Zhao
  2018-01-30  7:44 ` [dpdk-dev] [PATCH v2] " Wei Zhao
  0 siblings, 1 reply; 11+ messages in thread
From: Wei Zhao @ 2018-01-30  7:32 UTC (permalink / raw)
  To: dev; +Cc: orika, Wei Zhao

This patch will update example application of flow_filting document.
It add Tx queues configuration related comment.

Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
---
 doc/guides/sample_app_ug/flow_filtering.rst | 112 ++++++++++++++++++----------
 1 file changed, 74 insertions(+), 38 deletions(-)

diff --git a/doc/guides/sample_app_ug/flow_filtering.rst b/doc/guides/sample_app_ug/flow_filtering.rst
index 725dcb4..76a04b4 100644
--- a/doc/guides/sample_app_ug/flow_filtering.rst
+++ b/doc/guides/sample_app_ug/flow_filtering.rst
@@ -167,44 +167,65 @@ application is shown below:
            struct rte_eth_conf port_conf = {
                    .rxmode = {
                            .split_hdr_size = 0,
-                           /**< Header Split disabled */
-                           .header_split   = 0,
-                           /**< IP checksum offload disabled */
-                           .hw_ip_checksum = 0,
-                           /**< VLAN filtering disabled */
-                           .hw_vlan_filter = 0,
-                           /**< Jumbo Frame Support disabled */
-                           .jumbo_frame    = 0,
-                           /**< CRC stripped by hardware */
-                           .hw_strip_crc   = 1,
+                           .ignore_offload_bitfield = 1,
+                           .offloads = DEV_RX_OFFLOAD_CRC_STRIP,
+                           },
+                   .txmode = {
+                           .offloads =
+                                   DEV_TX_OFFLOAD_VLAN_INSERT |
+                                   DEV_TX_OFFLOAD_IPV4_CKSUM  |
+                                   DEV_TX_OFFLOAD_UDP_CKSUM   |
+                                   DEV_TX_OFFLOAD_TCP_CKSUM   |
+                                   DEV_TX_OFFLOAD_SCTP_CKSUM  |
+                                   DEV_TX_OFFLOAD_TCP_TSO,
                    },
            };
+           struct rte_eth_txconf txq_conf;
+           struct rte_eth_rxconf rxq_conf;
+           struct rte_eth_dev_info dev_info;
 
            printf(":: initializing port: %d\n", port_id);
            ret = rte_eth_dev_configure(port_id,
-                                   nr_queues, nr_queues, &port_conf);
+                   nr_queues, nr_queues, &port_conf);
            if (ret < 0) {
                    rte_exit(EXIT_FAILURE,
                            ":: cannot configure device: err=%d, port=%u\n",
                            ret, port_id);
            }
 
+           rte_eth_dev_info_get(port_id, &dev_info);
+           rxq_conf = dev_info.default_rxconf;
+           rxq_conf.offloads = port_conf.rxmode.offloads;
            /* only set Rx queues: something we care only so far */
            for (i = 0; i < nr_queues; i++) {
                    ret = rte_eth_rx_queue_setup(port_id, i, 512,
-                                        rte_eth_dev_socket_id(port_id),
-                                        NULL,
-                                        mbuf_pool);
+                           rte_eth_dev_socket_id(port_id),
+                           &rxq_conf,
+                           mbuf_pool);
                    if (ret < 0) {
-                           rte_exit(EXIT_FAILURE,
-                              ":: Rx queue setup failed: err=%d, port=%u\n",
-                              ret, port_id);
+                            rte_exit(EXIT_FAILURE,
+                                    ":: Rx queue setup failed: err=%d,
+                                    port=%u\n",
+                                    ret, port_id);
                    }
            }
 
+           txq_conf = dev_info.default_txconf;
+           txq_conf.offloads = port_conf.txmode.offloads;
 
-           rte_eth_promiscuous_enable(port_id);
+           for (i = 0; i < nr_queues; i++) {
+                   ret = rte_eth_tx_queue_setup(port_id, i, 512,
+                           rte_eth_dev_socket_id(port_id),
+                           &txq_conf);
+                   if (ret < 0) {
+                           rte_exit(EXIT_FAILURE,
+                                   ":: Tx queue setup failed: err=%d,
+                                   port=%u\n",
+                                   ret, port_id);
+                   }
+          }
 
+           rte_eth_promiscuous_enable(port_id);
            ret = rte_eth_dev_start(port_id);
            if (ret < 0) {
                    rte_exit(EXIT_FAILURE,
@@ -223,20 +244,21 @@ The Ethernet port is configured with default settings using the
 .. code-block:: c
 
    struct rte_eth_conf port_conf = {
-                .rxmode = {
-                        .split_hdr_size = 0,
-                        /**< Header Split disabled */
-                        .header_split   = 0,
-                        /**< IP checksum offload disabled */
-                        .hw_ip_checksum = 0,
-                        /**< VLAN filtering disabled */
-                        .hw_vlan_filter = 0,
-                        /**< Jumbo Frame Support disabled */
-                        .jumbo_frame    = 0,
-                        /**< CRC stripped by hardware */
-                        .hw_strip_crc   = 1,
-                },
-   };
+           .rxmode = {
+                   .split_hdr_size = 0,
+                   .ignore_offload_bitfield = 1,
+                   .offloads = DEV_RX_OFFLOAD_CRC_STRIP,
+                   },
+           .txmode = {
+                   .offloads =
+                           DEV_TX_OFFLOAD_VLAN_INSERT |
+                           DEV_TX_OFFLOAD_IPV4_CKSUM  |
+                           DEV_TX_OFFLOAD_UDP_CKSUM   |
+                           DEV_TX_OFFLOAD_TCP_CKSUM   |
+                           DEV_TX_OFFLOAD_SCTP_CKSUM  |
+                           DEV_TX_OFFLOAD_TCP_TSO,
+                   },
+           };
 
    ret = rte_eth_dev_configure(port_id, nr_queues, nr_queues, &port_conf);
    if (ret < 0) {
@@ -244,23 +266,37 @@ The Ethernet port is configured with default settings using the
                  ":: cannot configure device: err=%d, port=%u\n",
                  ret, port_id);
    }
+   rte_eth_dev_info_get(port_id, &dev_info);
+   rxq_conf = dev_info.default_rxconf;
+   rxq_conf.offloads = port_conf.rxmode.offloads;
 
-For this example we are configuring number of rx queues that are connected to
-a single port.
+For this example we are configuring number of rx and tx queues that are connected
+to a single port.
 
 .. code-block:: c
 
    for (i = 0; i < nr_queues; i++) {
           ret = rte_eth_rx_queue_setup(port_id, i, 512,
                                        rte_eth_dev_socket_id(port_id),
-                                       NULL,
+                                       &rxq_conf,
                                        mbuf_pool);
           if (ret < 0) {
                   rte_exit(EXIT_FAILURE,
-                          ":: Rx queue setup failed: err=%d, port=%u\n",
-                          ret, port_id);
+                           ":: Rx queue setup failed: err=%d, port=%u\n",
+                           ret, port_id);
+          }
+   }
+
+   for (i = 0; i < nr_queues; i++) {
+          ret = rte_eth_tx_queue_setup(port_id, i, 512,
+                                       rte_eth_dev_socket_id(port_id),
+                                       &txq_conf);
+          if (ret < 0) {
+                  rte_exit(EXIT_FAILURE,
+                           ":: Tx queue setup failed: err=%d, port=%u\n",
+                           ret, port_id);
           }
-  }
+   }
 
 In the next step we create and apply the flow rule. which is to send packets
 with destination ip equals to 192.168.1.1 to queue number 1. The detail
-- 
2.9.3

^ permalink raw reply	[flat|nested] 11+ messages in thread

end of thread, other threads:[~2018-02-07  8:08 UTC | newest]

Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-01-30  7:32 [dpdk-dev] [PATCH] doc: update flow filting document Wei Zhao
2018-01-30  7:44 ` [dpdk-dev] [PATCH v2] " Wei Zhao
2018-01-30  9:22   ` Ori Kam
2018-01-31  2:22     ` Zhao1, Wei
2018-01-31  2:12   ` [dpdk-dev] [PATCH v3] doc: update flow filtering document Wei Zhao
2018-01-31  6:50     ` Zhang, Helin
2018-01-31 17:24     ` Ferruh Yigit
2018-02-05 15:31       ` Mcnamara, John
2018-02-06 14:18         ` Ferruh Yigit
2018-02-07  8:07           ` Zhao1, Wei
2018-02-07  7:37         ` Zhao1, Wei

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).