From: Julien Meunier <julien.meunier@nokia.com>
To: <konstantin.ananyev@intel.com>, <wenzhuo.lu@intel.com>,
<wei.zhao1@intel.com>, <qi.z.zhang@intel.com>
Cc: <dev@dpdk.org>
Subject: [dpdk-dev] [PATCH 2/2] net/ixgbe: add support of loopback for X540/X550
Date: Thu, 7 Feb 2019 19:30:05 +0200 [thread overview]
Message-ID: <20190207173005.38372-2-julien.meunier@nokia.com> (raw)
In-Reply-To: <20190207173005.38372-1-julien.meunier@nokia.com>
Loopback mode is also supported on X540 and X550 NICs, according to
their datasheet (section 15.2). The way to set it up is a little
different of the 82599.
Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
---
v2:
- disable / enable autoneg when loopback is requested for X540 / X550
---
drivers/net/ixgbe/base/ixgbe_type.h | 1 +
drivers/net/ixgbe/base/ixgbe_x540.c | 26 ++++++++++++++++
drivers/net/ixgbe/base/ixgbe_x540.h | 2 ++
drivers/net/ixgbe/base/ixgbe_x550.c | 26 ++++++++++++++++
drivers/net/ixgbe/base/ixgbe_x550.h | 1 +
drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++-
drivers/net/ixgbe/ixgbe_rxtx.c | 61 +++++++++++++++++++++++++++++++++++--
7 files changed, 117 insertions(+), 5 deletions(-)
diff --git a/drivers/net/ixgbe/base/ixgbe_type.h b/drivers/net/ixgbe/base/ixgbe_type.h
index 077b8f0..c4af31e 100644
--- a/drivers/net/ixgbe/base/ixgbe_type.h
+++ b/drivers/net/ixgbe/base/ixgbe_type.h
@@ -1649,6 +1649,7 @@ struct ixgbe_dmac_config {
#define IXGBE_MII_5GBASE_T_ADVERTISE 0x0800
#define IXGBE_MII_100BASE_T_ADVERTISE 0x0100 /* full duplex, bit:8 */
#define IXGBE_MII_100BASE_T_ADVERTISE_HALF 0x0080 /* half duplex, bit:7 */
+#define IXGBE_MII_AUTONEG_ENABLE 0x1000
#define IXGBE_MII_RESTART 0x200
#define IXGBE_MII_AUTONEG_COMPLETE 0x20
#define IXGBE_MII_AUTONEG_LINK_UP 0x04
diff --git a/drivers/net/ixgbe/base/ixgbe_x540.c b/drivers/net/ixgbe/base/ixgbe_x540.c
index f00f0ea..a241d41 100644
--- a/drivers/net/ixgbe/base/ixgbe_x540.c
+++ b/drivers/net/ixgbe/base/ixgbe_x540.c
@@ -1032,3 +1032,29 @@ s32 ixgbe_blink_led_stop_X540(struct ixgbe_hw *hw, u32 index)
return IXGBE_SUCCESS;
}
+
+/*
+ * ixgbe_setup_phy_link_x540 - Enable/disable the autoneg
+ * @hw: pointer to hardware structure
+ * enable: enable/disable the autoneg
+ **/
+s32 ixgbe_setup_phy_autoneg_x540(struct ixgbe_hw *hw, bool enable)
+{
+ s32 status = IXGBE_SUCCESS;
+ u16 autoneg_reg = IXGBE_MII_AUTONEG_REG;
+
+ DEBUGFUNC("ixgbe_setup_phy_autoneg_x540");
+
+ hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
+
+ if (enable)
+ autoneg_reg |= IXGBE_MII_AUTONEG_ENABLE;
+ else
+ autoneg_reg &= ~IXGBE_MII_AUTONEG_ENABLE;
+
+ hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
+
+ return status;
+}
diff --git a/drivers/net/ixgbe/base/ixgbe_x540.h b/drivers/net/ixgbe/base/ixgbe_x540.h
index 231dfe5..ef939ce 100644
--- a/drivers/net/ixgbe/base/ixgbe_x540.h
+++ b/drivers/net/ixgbe/base/ixgbe_x540.h
@@ -34,5 +34,7 @@ void ixgbe_init_swfw_sync_X540(struct ixgbe_hw *hw);
s32 ixgbe_blink_led_start_X540(struct ixgbe_hw *hw, u32 index);
s32 ixgbe_blink_led_stop_X540(struct ixgbe_hw *hw, u32 index);
+
+s32 ixgbe_setup_phy_autoneg_x540(struct ixgbe_hw *hw, bool enable);
#endif /* _IXGBE_X540_H_ */
diff --git a/drivers/net/ixgbe/base/ixgbe_x550.c b/drivers/net/ixgbe/base/ixgbe_x550.c
index a920a14..f4ee188 100644
--- a/drivers/net/ixgbe/base/ixgbe_x550.c
+++ b/drivers/net/ixgbe/base/ixgbe_x550.c
@@ -4652,3 +4652,29 @@ bool ixgbe_fw_recovery_mode_X550(struct ixgbe_hw *hw)
return !!(fwsm & IXGBE_FWSM_FW_NVM_RECOVERY_MODE);
}
+
+/*
+ * ixgbe_setup_phy_link_x550 - Enable/disable the autoneg
+ * @hw: pointer to hardware structure
+ * enable: enable/disable the autoneg
+ **/
+s32 ixgbe_setup_phy_autoneg_x550(struct ixgbe_hw *hw, bool enable)
+{
+ s32 status = IXGBE_SUCCESS;
+ u16 autoneg_reg = IXGBE_MII_AUTONEG_REG;
+
+ DEBUGFUNC("ixgbe_setup_phy_autoneg_x550");
+
+ hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
+
+ if (enable)
+ autoneg_reg |= IXGBE_MII_AUTONEG_ENABLE;
+ else
+ autoneg_reg &= ~IXGBE_MII_AUTONEG_ENABLE;
+
+ hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
+
+ return status;
+}
diff --git a/drivers/net/ixgbe/base/ixgbe_x550.h b/drivers/net/ixgbe/base/ixgbe_x550.h
index 3bd98f2..dd4fa18 100644
--- a/drivers/net/ixgbe/base/ixgbe_x550.h
+++ b/drivers/net/ixgbe/base/ixgbe_x550.h
@@ -93,4 +93,5 @@ s32 ixgbe_identify_sfp_module_X550em(struct ixgbe_hw *hw);
s32 ixgbe_led_on_t_X550em(struct ixgbe_hw *hw, u32 led_idx);
s32 ixgbe_led_off_t_X550em(struct ixgbe_hw *hw, u32 led_idx);
bool ixgbe_fw_recovery_mode_X550(struct ixgbe_hw *hw);
+s32 ixgbe_setup_phy_autoneg_x550(struct ixgbe_hw *hw, bool enable);
#endif /* _IXGBE_X550_H_ */
diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h
index 565c69c..c60a697 100644
--- a/drivers/net/ixgbe/ixgbe_ethdev.h
+++ b/drivers/net/ixgbe/ixgbe_ethdev.h
@@ -65,9 +65,8 @@
#define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us */
/* Loopback operation modes */
-/* 82599 specific loopback operation types */
-#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is disabled. */
-#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback operation is enabled. */
+#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is disabled. */
+#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is enabled. */
#define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum Jumbo frame size. */
diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c b/drivers/net/ixgbe/ixgbe_rxtx.c
index c9a70a8..1472d13 100644
--- a/drivers/net/ixgbe/ixgbe_rxtx.c
+++ b/drivers/net/ixgbe/ixgbe_rxtx.c
@@ -49,6 +49,8 @@
#include "ixgbe_ethdev.h"
#include "base/ixgbe_dcb.h"
#include "base/ixgbe_common.h"
+#include "base/ixgbe_x540.h"
+#include "base/ixgbe_x550.h"
#include "ixgbe_rxtx.h"
#ifdef RTE_LIBRTE_IEEE1588
@@ -3174,6 +3176,7 @@ ixgbe_dev_clear_queues(struct rte_eth_dev *dev)
unsigned i;
struct ixgbe_adapter *adapter =
(struct ixgbe_adapter *)dev->data->dev_private;
+ struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
PMD_INIT_FUNC_TRACE();
@@ -3194,6 +3197,15 @@ ixgbe_dev_clear_queues(struct rte_eth_dev *dev)
ixgbe_reset_rx_queue(adapter, rxq);
}
}
+ /* If loopback mode was enabled, reconfigure the link accordingly */
+ if (dev->data->dev_conf.lpbk_mode != 0) {
+ if (hw->mac.type == ixgbe_mac_X540)
+ ixgbe_setup_phy_autoneg_x540(hw, true);
+ else if (hw->mac.type == ixgbe_mac_X550 ||
+ hw->mac.type == ixgbe_mac_X550EM_x ||
+ hw->mac.type == ixgbe_mac_X550EM_a)
+ ixgbe_setup_phy_autoneg_x550(hw, true);
+ }
}
void
@@ -5074,8 +5086,12 @@ ixgbe_check_supported_loopback_mode(struct rte_eth_dev *dev)
{
struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
- if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
- if (hw->mac.type == ixgbe_mac_82599EB)
+ if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
+ if (hw->mac.type == ixgbe_mac_82599EB ||
+ hw->mac.type == ixgbe_mac_X540 ||
+ hw->mac.type == ixgbe_mac_X550 ||
+ hw->mac.type == ixgbe_mac_X550EM_x ||
+ hw->mac.type == ixgbe_mac_X550EM_a)
return 0;
return -ENOTSUP;
@@ -5108,6 +5124,41 @@ ixgbe_setup_loopback_link_82599(struct ixgbe_hw *hw)
msec_delay(50);
}
+/*
+ * Set up link loopback for X540 mode Tx->Rx.
+ */
+static inline void __attribute__((cold))
+ixgbe_setup_loopback_link_x540(struct ixgbe_hw *hw)
+{
+ uint32_t macc;
+ PMD_INIT_FUNC_TRACE();
+
+ /* datasheet 15.2.1: disable AUTONEG (PHY Bit 7.0.C) */
+ ixgbe_setup_phy_autoneg_x540(hw, false);
+
+ /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
+ macc = IXGBE_READ_REG(hw, IXGBE_MACC);
+ macc |= IXGBE_MACC_FLU;
+ IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
+}
+
+/*
+ * Set up link loopback for X550 mode Tx->Rx.
+ */
+static inline void __attribute__((cold))
+ixgbe_setup_loopback_link_x550(struct ixgbe_hw *hw)
+{
+ uint32_t macc;
+ PMD_INIT_FUNC_TRACE();
+
+ /* datasheet 15.2.1: disable AUTONEG (PHY Bit 7.0.C) */
+ ixgbe_setup_phy_autoneg_x550(hw, false);
+
+ /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
+ macc = IXGBE_READ_REG(hw, IXGBE_MACC);
+ macc |= IXGBE_MACC_FLU;
+ IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
+}
/*
* Start Transmit and Receive Units.
@@ -5172,6 +5223,12 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev *dev)
if (dev->data->dev_conf.lpbk_mode != 0) {
if (hw->mac.type == ixgbe_mac_82599EB)
ixgbe_setup_loopback_link_82599(hw);
+ else if (hw->mac.type == ixgbe_mac_X540)
+ ixgbe_setup_loopback_link_x540(hw);
+ else if (hw->mac.type == ixgbe_mac_X550 ||
+ hw->mac.type == ixgbe_mac_X550EM_x ||
+ hw->mac.type == ixgbe_mac_X550EM_a)
+ ixgbe_setup_loopback_link_x550(hw);
}
#ifdef RTE_LIBRTE_SECURITY
--
2.10.2
next prev parent reply other threads:[~2019-02-07 17:30 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-02 16:00 [dpdk-dev] [PATCH] " Julien Meunier
2019-01-07 6:53 ` Zhang, Qi Z
2019-01-07 15:53 ` Meunier, Julien (Nokia - FR/Paris-Saclay)
2019-01-08 10:10 ` Zhao1, Wei
2019-01-08 12:39 ` Zhang, Qi Z
2019-01-08 20:18 ` Meunier, Julien (Nokia - FR/Paris-Saclay)
2019-01-09 1:30 ` Zhao1, Wei
2019-01-07 10:05 ` Zhao1, Wei
2019-01-07 16:04 ` Meunier, Julien (Nokia - FR/Paris-Saclay)
2019-01-08 3:10 ` Zhao1, Wei
2019-02-07 17:30 ` [dpdk-dev] [PATCH 1/2] net/ixgbe: do not start on unsupported loopback mode Julien Meunier
2019-02-07 17:30 ` Julien Meunier [this message]
2019-02-12 6:37 ` [dpdk-dev] [PATCH 2/2] net/ixgbe: add support of loopback for X540/X550 Zhao1, Wei
2019-02-18 11:20 ` Meunier, Julien (Nokia - FR/Paris-Saclay)
2019-02-12 6:36 ` [dpdk-dev] [PATCH 1/2] net/ixgbe: do not start on unsupported loopback mode Zhao1, Wei
2019-02-20 21:05 ` [dpdk-dev] [PATCH v3 " Julien Meunier
2019-02-20 21:05 ` [dpdk-dev] [PATCH v3 2/2] net/ixgbe: add support of loopback for X540/X550 Julien Meunier
2019-02-21 2:30 ` Zhao1, Wei
2019-03-01 7:46 ` Zhang, Qi Z
2019-03-01 7:45 ` [dpdk-dev] [PATCH v3 1/2] net/ixgbe: do not start on unsupported loopback mode Zhang, Qi Z
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190207173005.38372-2-julien.meunier@nokia.com \
--to=julien.meunier@nokia.com \
--cc=dev@dpdk.org \
--cc=konstantin.ananyev@intel.com \
--cc=qi.z.zhang@intel.com \
--cc=wei.zhao1@intel.com \
--cc=wenzhuo.lu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).