[dpdk-dev] [PATCH 1/5] doc: improve firmware configuration in mlx5 guide

[Thomas Monjalon <thomas@monjalon.net>]

The command mlxconfig was not enough explained and too much verbose
at the same time.
The syntax is now explained in introduction before listing the options,
without repeating the commands.
Some options, which are explained elsewhere in the doc,
are added to this list.

Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
---
 doc/guides/nics/mlx5.rst | 53 +++++++++++++++++++++++-----------------
 1 file changed, 30 insertions(+), 23 deletions(-)

diff --git a/doc/guides/nics/mlx5.rst b/doc/guides/nics/mlx5.rst
index 46538b8f1..32b1900bd 100644
--- a/doc/guides/nics/mlx5.rst
+++ b/doc/guides/nics/mlx5.rst
@@ -575,46 +575,53 @@ Run-time configuration
 Firmware configuration
 ~~~~~~~~~~~~~~~~~~~~~~
 
-- L3 VXLAN and VXLAN-GPE destination UDP port
+Firmware features can be configured as key/value pairs.
 
-   .. code-block:: console
+The command to set a value is::
 
-     mlxconfig -d <mst device> set IP_OVER_VXLAN_EN=1
-     mlxconfig -d <mst device> set IP_OVER_VXLAN_PORT=<udp dport>
+  mlxconfig -d <device> set <key>=<value>
 
-  Verify configurations are set:
+The command to query a value is::
 
-   .. code-block:: console
+  mlxconfig -d <device> query | grep <key>
 
-     mlxconfig -d <mst device> query | grep IP_OVER_VXLAN
-     IP_OVER_VXLAN_EN                    True(1)
-     IP_OVER_VXLAN_PORT                  <udp dport>
+The device name for the command ``mlxconfig`` can be either the PCI address,
+or the mst device name found with::
 
-- enable ICMP/ICMP6's code/type field matching
+  mst status
 
-   .. code-block:: console
+Below are some firmware configurations listed.
 
-     mlxconfig -d <mst device> set FLEX_PARSER_PROFILE_ENABLE=2
+- link type::
 
-  Verify configurations are set:
+    LINK_TYPE_P1
+    LINK_TYPE_P2
+    value: 1=Infiniband 2=Ethernet 3=VPI(auto-sense)
 
-   .. code-block:: console
+- enable SR-IOV::
 
-     mlxconfig -d <mst device> query | grep FLEX_PARSER_PROFILE_ENABLE
-     FLEX_PARSER_PROFILE_ENABLE         2
+    SRIOV_EN=1
 
-- IP-in-IP tunnel enable
+- maximum number of SR-IOV virtual functions::
 
-   .. code-block:: console
+    NUM_OF_VFS=<max>
 
-     mlxconfig -d <mst device> set FLEX_PARSER_PROFILE_ENABLE=0
+- aggressive CQE zipping::
 
-  Verify configurations are set:
+    CQE_COMPRESSION=1
 
-   .. code-block:: console
+- L3 VXLAN and VXLAN-GPE destination UDP port::
 
-     mlxconfig -d <mst device> query | grep FLEX_PARSER_PROFILE_ENABLE
-     FLEX_PARSER_PROFILE_ENABLE          0
+    IP_OVER_VXLAN_EN=1
+    IP_OVER_VXLAN_PORT=<udp dport>
+
+- enable IP-in-IP tunnel flow matching::
+
+    FLEX_PARSER_PROFILE_ENABLE=0
+
+- enable ICMP/ICMP6 code/type fields matching::
+
+    FLEX_PARSER_PROFILE_ENABLE=2
 
 Prerequisites
 -------------
-- 
2.21.0