[PATCH 04/11] net/ixgbe: enable vector stubs for RISC-V

[Stanislaw Kardach <kda@semihalf.com>]

Re-use vector processing stubs in ixgbe PMD defined for PPC for RISC-V.
This enables ixgbe PMD usage in scalar mode on this architecture.

The ixgbe PMD driver was validated with Intel X520-DA2 NIC and the
test-pmd application. Packet transfer checked using all UIO drivers
available for non-IOMMU platforms: uio_pci_generic, vfio-pci noiommu and
igb_uio.

Signed-off-by: Stanislaw Kardach <kda@semihalf.com>
Sponsored-by: Frank Zhao <Frank.Zhao@starfivetech.com>
Sponsored-by: Sam Grove <sam.grove@sifive.com>
---
 doc/guides/nics/features/ixgbe.ini | 1 +
 drivers/net/ixgbe/ixgbe_rxtx.c     | 4 ++--
 drivers/net/ixgbe/meson.build      | 6 ------
 3 files changed, 3 insertions(+), 8 deletions(-)

diff --git a/doc/guides/nics/features/ixgbe.ini b/doc/guides/nics/features/ixgbe.ini
index c5333d1142..b776ca1cf1 100644
--- a/doc/guides/nics/features/ixgbe.ini
+++ b/doc/guides/nics/features/ixgbe.ini
@@ -54,6 +54,7 @@ Windows              = Y
 ARMv8                = Y
 x86-32               = Y
 x86-64               = Y
+rv64                 = Y
 
 [rte_flow items]
 eth                  = Y
diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c b/drivers/net/ixgbe/ixgbe_rxtx.c
index 9e8ea366a5..009d9b624a 100644
--- a/drivers/net/ixgbe/ixgbe_rxtx.c
+++ b/drivers/net/ixgbe/ixgbe_rxtx.c
@@ -5957,8 +5957,8 @@ ixgbe_config_rss_filter(struct rte_eth_dev *dev,
 	return 0;
 }
 
-/* Stubs needed for linkage when RTE_ARCH_PPC_64 is set */
-#if defined(RTE_ARCH_PPC_64)
+/* Stubs needed for linkage when RTE_ARCH_PPC_64 or RTE_ARCH_RISCV is set */
+#if defined(RTE_ARCH_PPC_64) || defined(RTE_ARCH_RISCV)
 int
 ixgbe_rx_vec_dev_conf_condition_check(struct rte_eth_dev __rte_unused *dev)
 {
diff --git a/drivers/net/ixgbe/meson.build b/drivers/net/ixgbe/meson.build
index 88539e97d5..162f8d5f46 100644
--- a/drivers/net/ixgbe/meson.build
+++ b/drivers/net/ixgbe/meson.build
@@ -1,12 +1,6 @@
 # SPDX-License-Identifier: BSD-3-Clause
 # Copyright(c) 2017 Intel Corporation
 
-if arch_subdir == 'riscv'
-		build = false
-		reason = 'riscv arch not supported'
-		subdir_done()
-endif
-
 cflags += ['-DRTE_LIBRTE_IXGBE_BYPASS']
 
 subdir('base')
-- 
2.30.2