[PATCH V3 2/2] net/hns3: support backplane media type

[Dongdong Liu <liudongdong3@huawei.com>]

From: Chengwen Feng <fengchengwen@huawei.com>

The 802.11 physical PMA sub-layer defines three media: copper, fiber and
backplane. For PMD, the backplane is similar to the fiber, the main
differences are that backplane doesn't have optical module.

Because the interface of firmware fiber is also applicable to the
backplane, this patch supports the backplane only through simple
extension.

Cc: stable@dpdk.org

Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
---
v2->v3:
- move the HiSilicon update above Intel updates.
v1->v2:
- document new 'backplane' media type support in release notes.
---
 doc/guides/rel_notes/release_22_07.rst |  4 ++
 drivers/net/hns3/hns3_ethdev.c         | 54 ++++++++++++++------------
 2 files changed, 34 insertions(+), 24 deletions(-)

diff --git a/doc/guides/rel_notes/release_22_07.rst b/doc/guides/rel_notes/release_22_07.rst
index dd371952c3..395fb6cad8 100644
--- a/doc/guides/rel_notes/release_22_07.rst
+++ b/doc/guides/rel_notes/release_22_07.rst
@@ -122,6 +122,10 @@ New Features
   * Added support for Atomic Rules PCI device IDs ``0x101a, 0x101b, 0x101c``.
   * Added PMD support for virtual functions and vfio_pci driver.
 
+* **Updated HiSilicon hns3 driver.**
+
+  * Added support for backplane media type.
+
 * **Updated Intel iavf driver.**
 
   * Added Tx QoS queue rate limitation support.
diff --git a/drivers/net/hns3/hns3_ethdev.c b/drivers/net/hns3/hns3_ethdev.c
index 6c77c8b964..b17a3e8669 100644
--- a/drivers/net/hns3/hns3_ethdev.c
+++ b/drivers/net/hns3/hns3_ethdev.c
@@ -2787,11 +2787,8 @@ hns3_check_media_type(struct hns3_hw *hw, uint8_t media_type)
 		}
 		break;
 	case HNS3_MEDIA_TYPE_FIBER:
-		ret = 0;
-		break;
 	case HNS3_MEDIA_TYPE_BACKPLANE:
-		PMD_INIT_LOG(ERR, "Media type is Backplane, not supported.");
-		ret = -EOPNOTSUPP;
+		ret = 0;
 		break;
 	default:
 		PMD_INIT_LOG(ERR, "Unknown media type = %u!", media_type);
@@ -4244,14 +4241,11 @@ hns3_update_link_info(struct rte_eth_dev *eth_dev)
 {
 	struct hns3_adapter *hns = eth_dev->data->dev_private;
 	struct hns3_hw *hw = &hns->hw;
-	int ret = 0;
 
 	if (hw->mac.media_type == HNS3_MEDIA_TYPE_COPPER)
-		ret = hns3_update_copper_link_info(hw);
-	else if (hw->mac.media_type == HNS3_MEDIA_TYPE_FIBER)
-		ret = hns3_update_fiber_link_info(hw);
+		return hns3_update_copper_link_info(hw);
 
-	return ret;
+	return hns3_update_fiber_link_info(hw);
 }
 
 static int
@@ -4544,11 +4538,13 @@ hns3_get_port_supported_speed(struct rte_eth_dev *eth_dev)
 	if (ret)
 		return ret;
 
-	if (mac->media_type == HNS3_MEDIA_TYPE_FIBER) {
+	if (mac->media_type == HNS3_MEDIA_TYPE_FIBER ||
+	    mac->media_type == HNS3_MEDIA_TYPE_BACKPLANE) {
 		/*
 		 * Some firmware does not support the report of supported_speed,
-		 * and only report the effective speed of SFP. In this case, it
-		 * is necessary to use the SFP's speed as the supported_speed.
+		 * and only report the effective speed of SFP/backplane. In this
+		 * case, it is necessary to use the SFP/backplane's speed as the
+		 * supported_speed.
 		 */
 		if (mac->supported_speed == 0)
 			mac->supported_speed =
@@ -4810,7 +4806,7 @@ hns3_check_port_speed(struct hns3_hw *hw, uint32_t link_speeds)
 
 	if (mac->media_type == HNS3_MEDIA_TYPE_COPPER)
 		speed_bit = hns3_convert_link_speeds2bitmap_copper(link_speeds);
-	else if (mac->media_type == HNS3_MEDIA_TYPE_FIBER)
+	else
 		speed_bit = hns3_convert_link_speeds2bitmap_fiber(link_speeds);
 
 	if (!(speed_bit & supported_speed)) {
@@ -4954,6 +4950,19 @@ hns3_set_fiber_port_link_speed(struct hns3_hw *hw,
 	return hns3_cfg_mac_speed_dup(hw, cfg->speed, cfg->duplex);
 }
 
+static const char *
+hns3_get_media_type_name(uint8_t media_type)
+{
+	if (media_type == HNS3_MEDIA_TYPE_FIBER)
+		return "fiber";
+	else if (media_type == HNS3_MEDIA_TYPE_COPPER)
+		return "copper";
+	else if (media_type == HNS3_MEDIA_TYPE_BACKPLANE)
+		return "backplane";
+	else
+		return "unknown";
+}
+
 static int
 hns3_set_port_link_speed(struct hns3_hw *hw,
 			 struct hns3_set_link_speed_cfg *cfg)
@@ -4968,18 +4977,15 @@ hns3_set_port_link_speed(struct hns3_hw *hw,
 #endif
 
 		ret = hns3_set_copper_port_link_speed(hw, cfg);
-		if (ret) {
-			hns3_err(hw, "failed to set copper port link speed,"
-				 "ret = %d.", ret);
-			return ret;
-		}
-	} else if (hw->mac.media_type == HNS3_MEDIA_TYPE_FIBER) {
+	} else {
 		ret = hns3_set_fiber_port_link_speed(hw, cfg);
-		if (ret) {
-			hns3_err(hw, "failed to set fiber port link speed,"
-				 "ret = %d.", ret);
-			return ret;
-		}
+	}
+
+	if (ret) {
+		hns3_err(hw, "failed to set %s port link speed, ret = %d.",
+			 hns3_get_media_type_name(hw->mac.media_type),
+			 ret);
+		return ret;
 	}
 
 	return 0;
-- 
2.22.0