From: Vasily Philipov <vasilyf@mellanox.com>
To: dev@dpdk.org
Cc: Vasily Philipov <vasilyf@mellanox.com>,
Jingjing Wu <jingjing.wu@intel.com>,
Adrien Mazarguil <adrien.mazarguil@6wind.com>
Subject: [dpdk-dev] [PATCH] app/testpmd: add flow isolate all parameter
Date: Sun, 9 Jul 2017 11:08:05 +0300 [thread overview]
Message-ID: <2d0c842d7c1eb46845610057544dcfab08550933.1499585615.git.vasilyf@mellanox.com> (raw)
Providing this parameter requests flow API isolated mode on all ports at
initialization time. It ensures all traffic is received through the
configured flow rules only (see flow command).
Ports that do not support this mode are automatically discarded.
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>
---
app/test-pmd/parameters.c | 5 +++++
app/test-pmd/testpmd.c | 14 ++++++++++++++
app/test-pmd/testpmd.h | 1 +
doc/guides/testpmd_app_ug/run_app.rst | 8 ++++++++
4 files changed, 28 insertions(+)
diff --git a/app/test-pmd/parameters.c b/app/test-pmd/parameters.c
index 958b3d0..c20ce65 100644
--- a/app/test-pmd/parameters.c
+++ b/app/test-pmd/parameters.c
@@ -215,6 +215,8 @@
"enable print of designated event or all of them.");
printf(" --mask-event <unknown|intr_lsc|queue_state|intr_reset|vf_mbox|macsec|intr_rmv|all>: "
"disable print of designated event or all of them.");
+ printf(" --flow-isolate-all: "
+ "requests flow API isolated mode on all ports at initialization time.");
}
#ifdef RTE_LIBRTE_CMDLINE
@@ -630,6 +632,7 @@
{ "tx-queue-stats-mapping", 1, 0, 0 },
{ "rx-queue-stats-mapping", 1, 0, 0 },
{ "no-flush-rx", 0, 0, 0 },
+ { "flow-isolate-all", 0, 0, 0 },
{ "txpkts", 1, 0, 0 },
{ "disable-link-check", 0, 0, 0 },
{ "no-lsc-interrupt", 0, 0, 0 },
@@ -1105,6 +1108,8 @@
lsc_interrupt = 0;
if (!strcmp(lgopts[opt_idx].name, "no-rmv-interrupt"))
rmv_interrupt = 0;
+ if (!strcmp(lgopts[opt_idx].name, "flow-isolate-all"))
+ flow_isolate_all = 1;
if (!strcmp(lgopts[opt_idx].name, "print-event"))
if (parse_event_printing_config(optarg, 1)) {
rte_exit(EXIT_FAILURE,
diff --git a/app/test-pmd/testpmd.c b/app/test-pmd/testpmd.c
index 308c1b7..d618651 100644
--- a/app/test-pmd/testpmd.c
+++ b/app/test-pmd/testpmd.c
@@ -271,6 +271,11 @@ struct fwd_engine * fwd_engines[] = {
uint8_t no_flush_rx = 0; /* flush by default */
/*
+ * Flow API isolated mode.
+ */
+uint8_t flow_isolate_all;
+
+/*
* Avoids to check link status when starting/stopping a port.
*/
uint8_t no_link_check = 0; /* check by default */
@@ -1426,6 +1431,15 @@ static int eth_event_callback(uint8_t port_id,
if (port->need_reconfig > 0) {
port->need_reconfig = 0;
+ if (flow_isolate_all) {
+ int ret = port_flow_isolate(pi, 1);
+ if (ret) {
+ printf("Failed to apply isolated"
+ " mode on port %d\n", pi);
+ return -1;
+ }
+ }
+
printf("Configuring Port %d (socket %u)\n", pi,
port->socket_id);
/* configure port */
diff --git a/app/test-pmd/testpmd.h b/app/test-pmd/testpmd.h
index 9ccfb6d..33ff7f2 100644
--- a/app/test-pmd/testpmd.h
+++ b/app/test-pmd/testpmd.h
@@ -306,6 +306,7 @@ struct queue_stats_mappings {
extern uint8_t numa_support; /**< set by "--numa" parameter */
extern uint16_t port_topology; /**< set by "--port-topology" parameter */
extern uint8_t no_flush_rx; /**<set by "--no-flush-rx" parameter */
+extern uint8_t flow_isolate_all; /**<set by "--flow-isolate-all */
extern uint8_t mp_anon; /**< set by "--mp-anon" parameter */
extern uint8_t no_link_check; /**<set by "--disable-link-check" parameter */
extern volatile int test_done; /* stop packet forwarding when set to 1. */
diff --git a/doc/guides/testpmd_app_ug/run_app.rst b/doc/guides/testpmd_app_ug/run_app.rst
index e50c47f..e8303f3 100644
--- a/doc/guides/testpmd_app_ug/run_app.rst
+++ b/doc/guides/testpmd_app_ug/run_app.rst
@@ -500,3 +500,11 @@ The commandline options are:
Disable printing the occurrence of the designated event. Using all will
disable all of them.
+
+* ``--flow-isolate-all``
+
+ Providing this parameter requests flow API isolated mode on all ports at
+ initialization time. It ensures all traffic is received through the
+ configured flow rules only (see flow command).
+
+ Ports that do not support this mode are automatically discarded.
--
1.8.3.1
next reply other threads:[~2017-07-09 8:08 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-07-09 8:08 Vasily Philipov [this message]
2017-07-10 12:46 ` Adrien Mazarguil
2017-07-13 9:50 ` Thomas Monjalon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2d0c842d7c1eb46845610057544dcfab08550933.1499585615.git.vasilyf@mellanox.com \
--to=vasilyf@mellanox.com \
--cc=adrien.mazarguil@6wind.com \
--cc=dev@dpdk.org \
--cc=jingjing.wu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).