Re: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to reflect checksum support

["Varghese, Vipin" <vipin.varghese@intel.com>]

Hi Lee,

A humble suggestion being shared for document update, Based on DPDK 19.02-rc1 release both code and associated document update is to be in single patch file.

Note: I am not fully sure how this is applicable to 'isal.ini and isal.rst'. It will be good to have a check.

Thanks
Vipin Varghese

> -----Original Message-----
> From: dev <dev-bounces@dpdk.org> On Behalf Of Lee Daly
> Sent: Thursday, December 13, 2018 4:13 PM
> To: akhil.goyal@nxp.com
> Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> Subject: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to reflect checksum
> support
> 
> This updates the ISA-L compression driver guide on how to enable and use
> checksums.
> 
> This also updates the compression drivers features matrix.
> 
> V2:
> Documentation Changes
> V3:
> Added Release note
> 
> Signed-off-by: Lee Daly <lee.daly@intel.com>
> Acked-by: Fiona Trahe <fiona.trahe@intel.com>
> ---
>  doc/guides/compressdevs/features/isal.ini |  2 ++
>  doc/guides/compressdevs/isal.rst          | 30 ++++++++++++++++++++++++++++-
> -
>  doc/guides/rel_notes/release_19_02.rst    |  5 +++++
>  3 files changed, 35 insertions(+), 2 deletions(-)
> 
> diff --git a/doc/guides/compressdevs/features/isal.ini
> b/doc/guides/compressdevs/features/isal.ini
> index 919cf70..e705031 100644
> --- a/doc/guides/compressdevs/features/isal.ini
> +++ b/doc/guides/compressdevs/features/isal.ini
> @@ -12,5 +12,7 @@ OOP SGL In SGL Out = Y  OOP SGL In LB  Out = Y  OOP LB  In
> SGL Out = Y
>  Deflate            = Y
> +Adler32            = Y
> +Crc32              = Y
>  Fixed              = Y
>  Dynamic            = Y
> diff --git a/doc/guides/compressdevs/isal.rst b/doc/guides/compressdevs/isal.rst
> index 3bc3022..af1f41f 100644
> --- a/doc/guides/compressdevs/isal.rst
> +++ b/doc/guides/compressdevs/isal.rst
> @@ -27,6 +27,33 @@ Window size support:
> 
>      * 32K
> 
> +Checksum:
> +
> +    * CRC32
> +    * ADLER32
> +
> +To enable a checksum in the driver, the compression and/or
> +decompression xform structure, rte_comp_xform, must be filled with
> +either of the CompressDev checksum flags supported. ::
> +
> + compress_xform->compress.chksum = RTE_COMP_CHECKSUM_CRC32
> +
> + decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_CRC32
> +
> +::
> +
> + compress_xform->compress.chksum = RTE_COMP_CHECKSUM_ADLER32
> +
> + decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_ADLER32
> +
> +If you request a checksum for compression or decompression, the
> +checksum field in the operation structure,  ``op->output_chksum``, will
> +be filled with the checksum.
> +
> +.. Note::
> +
> + For the compression case above, your output buffer will need to be large
> enough to hold the compressed data plus a scratchpad for the checksum at the
> end, the scratchpad is 8 bytes for CRC32 and 4 bytes for Adler32.
> +
>  Level guide:
> 
>  The ISA-L levels have been mapped to somewhat correspond to the same ZLIB
> level, @@ -75,13 +102,12 @@ As a result the level mappings from the API to the
> PMD are shown below.
>   The above table only shows mapping when API calls for dynamic compression.
>   For fixed compression, regardless of API level, internally ISA-L level 0 is always
> used.
> 
> +
>  Limitations
>  -----------
> 
>  * Compressdev level 0, no compression, is not supported.
> 
> -* Checksums will not be supported until future release.
> -
>  Installation
>  ------------
> 
> diff --git a/doc/guides/rel_notes/release_19_02.rst
> b/doc/guides/rel_notes/release_19_02.rst
> index a94fa86..3a4d264 100644
> --- a/doc/guides/rel_notes/release_19_02.rst
> +++ b/doc/guides/rel_notes/release_19_02.rst
> @@ -54,6 +54,11 @@ New Features
>       Also, make sure to start the actual text at the margin.
>       =========================================================
> 
> +   * **Enabled checksum support in the ISA-L compressdev driver.**
> +
> +     Added support for both adler and crc32 checksums in the ISA-L PMD.
> +     This aids data integrity across both compression and decompression.
> +
> 
>  Removed Items
>  -------------
> --
> 2.7.4