DPDK patches and discussions
 help / color / mirror / Atom feed
* Re: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
@ 2015-03-31 10:25 Ananyev, Konstantin
  2015-03-31 11:40 ` Vlad Zolotarov
  0 siblings, 1 reply; 6+ messages in thread
From: Ananyev, Konstantin @ 2015-03-31 10:25 UTC (permalink / raw)
  To: Vlad Zolotarov, dev



> -----Original Message-----
> From: Vlad Zolotarov [mailto:vladz@cloudius-systems.com]
> Sent: Monday, March 30, 2015 4:57 PM
> To: Ananyev, Konstantin; dev@dpdk.org
> Subject: Re: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
> 
> 
> 
> On 03/30/15 18:37, Vlad Zolotarov wrote:
> >
> >
> > On 03/30/15 17:18, Ananyev, Konstantin wrote:
> >> Hi Vlad,
> >>
> >>> -----Original Message-----
> >>> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Vlad Zolotarov
> >>> Sent: Wednesday, March 18, 2015 5:52 PM
> >>> To: dev@dpdk.org
> >>> Subject: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
> >>>
> >>>      - Only x540 and 82599 devices support LRO.
> >>>      - Add the appropriate HW configuration.
> >>>      - Add RSC aware rx_pkt_burst() handlers:
> >>>         - Implemented bulk allocation and non-bulk allocation versions.
> >>>         - Add LRO-specific fields to rte_eth_rxmode, to
> >>> rte_eth_dev_data
> >>>           and to ixgbe_rx_queue.
> >>>         - Use the appropriate handler when LRO is requested.
> >>>
> >>> Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
> >>> ---
> >>> New in v8:
> >>>     - Took the RSC configuration code from ixgbe_dev_rx_init() into
> >>> a separate
> >>>       function - ixgbe_set_rsc().
> >>>     - Added some missing macros for HW configuration.
> >>>     - Styling adjustments:
> >>>        - Functions names.
> >>>        - Functions descriptions.
> >>>     - Reworked the ixgbe_free_rsc_cluster() code to make it more
> >>> readable.
> >>>     - Kill the HEADER_SPLIT flow in ixgbe_set_rsc() since it's not
> >>> supported by
> >>>       ixgbe PMD.
> >>>
> >>> New in v7:
> >>>     - Free not-yet-completed RSC aggregations in rte_eth_dev_stop()
> >>> flow.
> >>>     - Reset the sw_ring[].mbuf entry in a bulk allocation case.
> >>>       This is needed for ixgbe_rx_queue_release_mbufs().
> >>>     - _recv_pkts_lro(): added the missing memory barrier before RDT
> >>> update in a
> >>>       non-bulk allocation case.
> >>>     - Don't allow RSC when device is configured in an SR-IOV mode.
> >>>
> >>> New in v5:
> >>>     - Put the RTE_ETHDEV_HAS_LRO_SUPPORT definition at the beginning
> >>> of rte_ethdev.h.
> >>>     - Removed the "TODO: Remove me" comment near
> >>> RTE_ETHDEV_HAS_LRO_SUPPORT.
> >>>
> >>> New in v4:
> >>>     - Define RTE_ETHDEV_HAS_LRO_SUPPORT in rte_ethdev.h instead of
> >>>       RTE_ETHDEV_LRO_SUPPORT defined in config/common_linuxapp.
> >>>
> >>> New in v2:
> >>>     - Removed rte_eth_dev_data.lro_bulk_alloc.
> >>>     - Fixed a few styling and spelling issues.
> >>> ---
> >>>   lib/librte_ether/rte_ethdev.h           |   9 +-
> >>>   lib/librte_net/rte_ip.h                 |   3 +
> >>>   lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h |   6 +
> >>>   lib/librte_pmd_ixgbe/ixgbe_ethdev.c     |  11 +
> >>>   lib/librte_pmd_ixgbe/ixgbe_ethdev.h     |   5 +
> >>>   lib/librte_pmd_ixgbe/ixgbe_rxtx.c       | 610
> >>> +++++++++++++++++++++++++++++++-
> >>>   lib/librte_pmd_ixgbe/ixgbe_rxtx.h       |   6 +
> >>>   7 files changed, 642 insertions(+), 8 deletions(-)
> >>>
> >>> diff --git a/lib/librte_ether/rte_ethdev.h
> >>> b/lib/librte_ether/rte_ethdev.h
> >>> index 21aa359..61dc49a 100644
> >>> --- a/lib/librte_ether/rte_ethdev.h
> >>> +++ b/lib/librte_ether/rte_ethdev.h
> >>> @@ -172,6 +172,9 @@ extern "C" {
> >>>
> >>>   #include <stdint.h>
> >>>
> >>> +/* Use this macro to check if LRO API is supported */
> >>> +#define RTE_ETHDEV_HAS_LRO_SUPPORT
> >>> +
> >>>   #include <rte_log.h>
> >>>   #include <rte_interrupts.h>
> >>>   #include <rte_pci.h>
> >>> @@ -320,14 +323,15 @@ struct rte_eth_rxmode {
> >>>       enum rte_eth_rx_mq_mode mq_mode;
> >>>       uint32_t max_rx_pkt_len;  /**< Only used if jumbo_frame
> >>> enabled. */
> >>>       uint16_t split_hdr_size;  /**< hdr buf size (header_split
> >>> enabled).*/
> >>> -    uint8_t header_split : 1, /**< Header Split enable. */
> >>> +    uint16_t header_split : 1, /**< Header Split enable. */
> >>>           hw_ip_checksum   : 1, /**< IP/UDP/TCP checksum offload
> >>> enable. */
> >>>           hw_vlan_filter   : 1, /**< VLAN filter enable. */
> >>>           hw_vlan_strip    : 1, /**< VLAN strip enable. */
> >>>           hw_vlan_extend   : 1, /**< Extended VLAN enable. */
> >>>           jumbo_frame      : 1, /**< Jumbo Frame Receipt enable. */
> >>>           hw_strip_crc     : 1, /**< Enable CRC stripping by
> >>> hardware. */
> >>> -        enable_scatter   : 1; /**< Enable scatter packets rx
> >>> handler */
> >>> +        enable_scatter   : 1, /**< Enable scatter packets rx
> >>> handler */
> >>> +        enable_lro       : 1; /**< Enable LRO */
> >>>   };
> >>>
> >>>   /**
> >>> @@ -1515,6 +1519,7 @@ struct rte_eth_dev_data {
> >>>       uint8_t port_id;           /**< Device [external] port
> >>> identifier. */
> >>>       uint8_t promiscuous   : 1, /**< RX promiscuous mode ON(1) /
> >>> OFF(0). */
> >>>           scattered_rx : 1,  /**< RX of scattered packets is ON(1) /
> >>> OFF(0) */
> >>> +        lro          : 1,  /**< RX LRO is ON(1) / OFF(0) */
> >>>           all_multicast : 1, /**< RX all multicast mode ON(1) /
> >>> OFF(0). */
> >>>           dev_started : 1;   /**< Device state: STARTED(1) /
> >>> STOPPED(0). */
> >>>   };
> >>> diff --git a/lib/librte_net/rte_ip.h b/lib/librte_net/rte_ip.h
> >>> index 64935d9..74c9ced 100644
> >>> --- a/lib/librte_net/rte_ip.h
> >>> +++ b/lib/librte_net/rte_ip.h
> >>> @@ -110,6 +110,9 @@ struct ipv4_hdr {
> >>>                          (((c) & 0xff) << 8)  | \
> >>>                          ((d) & 0xff))
> >>>
> >>> +/** Maximal IPv4 packet length (including a header) */
> >>> +#define IPV4_MAX_PKT_LEN        65535
> >>> +
> >>>   /** Internet header length mask for version_ihl field */
> >>>   #define IPV4_HDR_IHL_MASK    (0x0f)
> >>>   /**
> >>> diff --git a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
> >>> b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
> >>> index 9a66370..4998627 100644
> >>> --- a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
> >>> +++ b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
> >>> @@ -234,8 +234,14 @@ struct ixgbe_thermal_sensor_data {
> >>>   #define IXGBE_EITR(_i)        (((_i) <= 23) ? (0x00820 + ((_i) *
> >>> 4)) : \
> >>>                    (0x012300 + (((_i) - 24) * 4)))
> >>>   #define IXGBE_EITR_ITR_INT_MASK    0x00000FF8
> >>> +#define IXGBE_EITR_ITR_INT_SHIFT 3
> >>>   #define IXGBE_EITR_LLI_MOD    0x00008000
> >>>   #define IXGBE_EITR_CNT_WDIS    0x80000000
> >>> +/* EITR Inteval is in 2048ns uinits for 1G and 10G link */
> >>> +#define IXGBE_EITR_INTERVAL_UNIT_NS    2048
> >> Why is that? Why not just 2us as 82599 spec says?
> >> And then:
> >> +#define IXGBE_EITR_INTERVAL_US(us) (((us) /
> >> IXGBE_EITR_INTERVAL_UNIT_US << IXGBE_EITR_ITR_INT_SHIFT) &
> >> IXGBE_EITR_ITR_INT_MASK)
> >> ?
> >
> > Because spec doesn't say 2us but rather 2.048us - see 8.2.4.5.16
> > chapter of x540 spec.
> 
> The most confusing part is that 82599 Rev. 3.0 spec does say so. 

I see what you mean now.
Indeed that's a bit strange that in 82599 and X540 spec ITR_Interval units are different.
We sent a question about this to HW guys, but don't know when there will be an answer.
I suppose we can stick with 2.048 us case for now.
>From my understanding, even if 82599 uses 2us the difference in max timeout would be pretty small: 500 us vs 488 us
and shouldn't cause any performance drop. 
I wonder did try your LRO latest changes on 82599?
If yes, did you see any difference in performance vs previous version, when hardcoded value for 2us was used?    
Konstantin

>The  x540 spec I have is dated by March 2014 and 82599 spec is dated by
> November 2014 but according to changelog EITR description has never been
> updated. Therefore I conclude that the more recent device spec (x540)
> holds the most up to date content.
> 
> Pls., confirm.
> 
> thanks,
> vlad
> 
> >
> >>
> >>> +#define IXGBE_EITR_INTERVAL_US(us)    \
> >>> +   (((us) * 1000 / IXGBE_EITR_INTERVAL_UNIT_NS <<
> >>> IXGBE_EITR_ITR_INT_SHIFT) & \
> >>> +        IXGBE_EITR_ITR_INT_MASK)
> >>
> >> Unfortunately we are not supposed to change files under ixgbe
> >> subfirectory (except ixgbe_osdep.*).
> >> These files comes from ixgbe shared code and we treat them as read-only.
> >> You need to move these new macros you added into ixgbe_ethedev.h.
> >
> > Aha... Ok. No problem.
> >
> >>
> >> All other things look good to me.
> >> Konstantin
> >>
> >>>   #define IXGBE_IVAR(_i)        (0x00900 + ((_i) * 4)) /* 24 at
> >>> 0x900-0x960 */
> >>>   #define IXGBE_IVAR_MISC        0x00A00 /* misc MSI-X interrupt
> >>> causes */
> >>>   #define IXGBE_EITRSEL        0x00894
> >>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
> >>> b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
> >>> index 92d75db..923692e 100644
> >>> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
> >>> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
> >>> @@ -1645,6 +1645,7 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
> >>>
> >>>       /* Clear stored conf */
> >>>       dev->data->scattered_rx = 0;
> >>> +    dev->data->lro = 0;
> >>>
> >>>       /* Clear recorded link status */
> >>>       memset(&link, 0, sizeof(link));
> >>> @@ -2013,6 +2014,16 @@ ixgbe_dev_info_get(struct rte_eth_dev *dev,
> >>> struct rte_eth_dev_info *dev_info)
> >>>           DEV_RX_OFFLOAD_IPV4_CKSUM |
> >>>           DEV_RX_OFFLOAD_UDP_CKSUM  |
> >>>           DEV_RX_OFFLOAD_TCP_CKSUM;
> >>> +
> >>> +    /*
> >>> +     * RSC is only supported by 82599 and x540 PF devices in a
> >>> non-SR-IOV
> >>> +     * mode.
> >>> +     */
> >>> +    if ((hw->mac.type == ixgbe_mac_82599EB ||
> >>> +         hw->mac.type == ixgbe_mac_X540) &&
> >>> +        !RTE_ETH_DEV_SRIOV(dev).active)
> >>> +        dev_info->rx_offload_capa |= DEV_RX_OFFLOAD_TCP_LRO;
> >>> +
> >>>       dev_info->tx_offload_capa =
> >>>           DEV_TX_OFFLOAD_VLAN_INSERT |
> >>>           DEV_TX_OFFLOAD_IPV4_CKSUM  |
> >>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
> >>> b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
> >>> index ffe3471..7050340 100644
> >>> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
> >>> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
> >>> @@ -344,6 +344,11 @@ uint16_t ixgbe_recv_pkts(void *rx_queue, struct
> >>> rte_mbuf **rx_pkts,
> >>>   uint16_t ixgbe_recv_scattered_pkts(void *rx_queue,
> >>>           struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
> >>>
> >>> +uint16_t ixgbe_recv_pkts_lro_single_alloc(void *rx_queue,
> >>> +        struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
> >>> +uint16_t ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue,
> >>> +        struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
> >>> +
> >>>   uint16_t ixgbe_xmit_pkts(void *tx_queue, struct rte_mbuf **tx_pkts,
> >>>           uint16_t nb_pkts);
> >>>
> >>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
> >>> b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
> >>> index a08ae6a..daa4c45 100644
> >>> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
> >>> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
> >>> @@ -70,6 +70,7 @@
> >>>   #include <rte_sctp.h>
> >>>   #include <rte_string_fns.h>
> >>>   #include <rte_errno.h>
> >>> +#include <rte_ip.h>
> >>>
> >>>   #include "ixgbe_logs.h"
> >>>   #include "ixgbe/ixgbe_api.h"
> >>> @@ -1422,6 +1423,295 @@ ixgbe_fill_cluster_head_buf(
> >>>       }
> >>>   }
> >>>
> >>> +/**
> >>> + * ixgbe_recv_pkts_lro - receive handler for and LRO case.
> >>> + *
> >>> + * @rx_queue Rx queue handle
> >>> + * @rx_pkts table of received packets
> >>> + * @nb_pkts size of rx_pkts table
> >>> + * @bulk_alloc if TRUE bulk allocation is used for a HW ring refilling
> >>> + *
> >>> + * Handles the Rx HW ring completions when RSC feature is
> >>> configured. Uses an
> >>> + * additional ring of ixgbe_rsc_entry's that will hold the relevant
> >>> RSC info.
> >>> + *
> >>> + * We use the same logic as in Lunux and in FreeBSD ixgbe drivers:
> >>> + * 1) When non-EOP RSC completion arrives:
> >>> + *    a) Update the HEAD of the current RSC aggregation cluster
> >>> with the new
> >>> + *       segment's data length.
> >>> + *    b) Set the "next" pointer of the current segment to point to
> >>> the segment
> >>> + *       at the NEXTP index.
> >>> + *    c) Pass the HEAD of RSC aggregation cluster on to the next
> >>> NEXTP entry
> >>> + *       in the sw_rsc_ring.
> >>> + * 2) When EOP arrives we just update the cluster's total length
> >>> and offload
> >>> + *    flags and deliver the cluster up to the upper layers. In our
> >>> case - put it
> >>> + *    in the rx_pkts table.
> >>> + *
> >>> + * Returns the number of received packets/clusters (according to
> >>> the "bulk
> >>> + * receive" interface).
> >>> + */
> >>> +static inline uint16_t
> >>> +ixgbe_recv_pkts_lro(void *rx_queue, struct rte_mbuf **rx_pkts,
> >>> uint16_t nb_pkts,
> >>> +            bool bulk_alloc)
> >>> +{
> >>> +    struct ixgbe_rx_queue *rxq = rx_queue;
> >>> +    volatile union ixgbe_adv_rx_desc *rx_ring = rxq->rx_ring;
> >>> +    struct ixgbe_rx_entry *sw_ring = rxq->sw_ring;
> >>> +    struct ixgbe_rsc_entry *sw_rsc_ring = rxq->sw_rsc_ring;
> >>> +    uint16_t rx_id = rxq->rx_tail;
> >>> +    uint16_t nb_rx = 0;
> >>> +    uint16_t nb_hold = rxq->nb_rx_hold;
> >>> +    uint16_t prev_id = rxq->rx_tail;
> >>> +
> >>> +    while (nb_rx < nb_pkts) {
> >>> +        bool eop;
> >>> +        struct ixgbe_rx_entry *rxe;
> >>> +        struct ixgbe_rsc_entry *rsc_entry;
> >>> +        struct ixgbe_rsc_entry *next_rsc_entry;
> >>> +        struct ixgbe_rx_entry *next_rxe;
> >>> +        struct rte_mbuf *first_seg;
> >>> +        struct rte_mbuf *rxm;
> >>> +        struct rte_mbuf *nmb;
> >>> +        union ixgbe_adv_rx_desc rxd;
> >>> +        uint16_t data_len;
> >>> +        uint16_t next_id;
> >>> +        volatile union ixgbe_adv_rx_desc *rxdp;
> >>> +        uint32_t staterr;
> >>> +
> >>> +next_desc:
> >>> +        /*
> >>> +         * The code in this whole file uses the volatile pointer to
> >>> +         * ensure the read ordering of the status and the rest of the
> >>> +         * descriptor fields (on the compiler level only!!!). This
> >>> is so
> >>> +         * UGLY - why not to just use the compiler barrier instead?
> >>> DPDK
> >>> +         * even has the rte_compiler_barrier() for that.
> >>> +         *
> >>> +         * But most importantly this is just wrong because this
> >>> doesn't
> >>> +         * ensure memory ordering in a general case at all. For
> >>> +         * instance, DPDK is supposed to work on Power CPUs where
> >>> +         * compiler barrier may just not be enough!
> >>> +         *
> >>> +         * I tried to write only this function properly to have a
> >>> +         * starting point (as a part of an LRO/RSC series) but the
> >>> +         * compiler cursed at me when I tried to cast away the
> >>> +         * "volatile" from rx_ring (yes, it's volatile too!!!). So,
> >>> I'm
> >>> +         * keeping it the way it is for now.
> >>> +         *
> >>> +         * The code in this file is broken in so many other places and
> >>> +         * will just not work on a big endian CPU anyway therefore the
> >>> +         * lines below will have to be revisited together with the
> >>> rest
> >>> +         * of the ixgbe PMD.
> >>> +         *
> >>> +         * TODO:
> >>> +         *    - Get rid of "volatile" crap and let the compiler do its
> >>> +         *      job.
> >>> +         *    - Use the proper memory barrier (rte_rmb()) to ensure
> >>> the
> >>> +         *      memory ordering below.
> >>> +         */
> >>> +        rxdp = &rx_ring[rx_id];
> >>> +        staterr = rte_le_to_cpu_32(rxdp->wb.upper.status_error);
> >>> +
> >>> +        if (!(staterr & IXGBE_RXDADV_STAT_DD))
> >>> +            break;
> >>> +
> >>> +        rxd = *rxdp;
> >>> +
> >>> +        PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_id=%u "
> >>> +                  "staterr=0x%x data_len=%u",
> >>> +               rxq->port_id, rxq->queue_id, rx_id, staterr,
> >>> +               rte_le_to_cpu_16(rxd.wb.upper.length));
> >>> +
> >>> +        if (!bulk_alloc) {
> >>> +            nmb = rte_rxmbuf_alloc(rxq->mb_pool);
> >>> +            if (nmb == NULL) {
> >>> +                PMD_RX_LOG(DEBUG, "RX mbuf alloc failed "
> >>> +                          "port_id=%u queue_id=%u",
> >>> +                       rxq->port_id, rxq->queue_id);
> >>> +
> >>> +                rte_eth_devices[rxq->port_id].data->
> >>> +                            rx_mbuf_alloc_failed++;
> >>> +                break;
> >>> +            }
> >>> +        } else if (nb_hold > rxq->rx_free_thresh) {
> >>> +            uint16_t next_rdt = rxq->rx_free_trigger;
> >>> +
> >>> +            if (!ixgbe_rx_alloc_bufs(rxq, false)) {
> >>> +                rte_wmb();
> >>> +                IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr,
> >>> +                            next_rdt);
> >>> +                nb_hold -= rxq->rx_free_thresh;
> >>> +            } else {
> >>> +                PMD_RX_LOG(DEBUG, "RX bulk alloc failed "
> >>> +                          "port_id=%u queue_id=%u",
> >>> +                       rxq->port_id, rxq->queue_id);
> >>> +
> >>> +                rte_eth_devices[rxq->port_id].data->
> >>> +                            rx_mbuf_alloc_failed++;
> >>> +                break;
> >>> +            }
> >>> +        }
> >>> +
> >>> +        nb_hold++;
> >>> +        rxe = &sw_ring[rx_id];
> >>> +        eop = staterr & IXGBE_RXDADV_STAT_EOP;
> >>> +
> >>> +        next_id = rx_id + 1;
> >>> +        if (next_id == rxq->nb_rx_desc)
> >>> +            next_id = 0;
> >>> +
> >>> +        /* Prefetch next mbuf while processing current one. */
> >>> +        rte_ixgbe_prefetch(sw_ring[next_id].mbuf);
> >>> +
> >>> +        /*
> >>> +         * When next RX descriptor is on a cache-line boundary,
> >>> +         * prefetch the next 4 RX descriptors and the next 4 pointers
> >>> +         * to mbufs.
> >>> +         */
> >>> +        if ((next_id & 0x3) == 0) {
> >>> +            rte_ixgbe_prefetch(&rx_ring[next_id]);
> >>> +            rte_ixgbe_prefetch(&sw_ring[next_id]);
> >>> +        }
> >>> +
> >>> +        rxm = rxe->mbuf;
> >>> +
> >>> +        if (!bulk_alloc) {
> >>> +            __le64 dma =
> >>> + rte_cpu_to_le_64(RTE_MBUF_DATA_DMA_ADDR_DEFAULT(nmb));
> >>> +            /*
> >>> +             * Update RX descriptor with the physical address of the
> >>> +             * new data buffer of the new allocated mbuf.
> >>> +             */
> >>> +            rxe->mbuf = nmb;
> >>> +
> >>> +            rxm->data_off = RTE_PKTMBUF_HEADROOM;
> >>> +            rxdp->read.hdr_addr = dma;
> >>> +            rxdp->read.pkt_addr = dma;
> >>> +        } else
> >>> +            rxe->mbuf = NULL;
> >>> +
> >>> +        /*
> >>> +         * Set data length & data buffer address of mbuf.
> >>> +         */
> >>> +        data_len = rte_le_to_cpu_16(rxd.wb.upper.length);
> >>> +        rxm->data_len = data_len;
> >>> +
> >>> +        if (!eop) {
> >>> +            uint16_t nextp_id;
> >>> +            /*
> >>> +             * Get next descriptor index:
> >>> +             *  - For RSC it's in the NEXTP field.
> >>> +             *  - For a scattered packet - it's just a following
> >>> +             *    descriptor.
> >>> +             */
> >>> +            if (ixgbe_rsc_count(&rxd))
> >>> +                nextp_id =
> >>> +                    (staterr & IXGBE_RXDADV_NEXTP_MASK) >>
> >>> +                               IXGBE_RXDADV_NEXTP_SHIFT;
> >>> +            else
> >>> +                nextp_id = next_id;
> >>> +
> >>> +            next_rsc_entry = &sw_rsc_ring[nextp_id];
> >>> +            next_rxe = &sw_ring[nextp_id];
> >>> +            rte_ixgbe_prefetch(next_rxe);
> >>> +        }
> >>> +
> >>> +        rsc_entry = &sw_rsc_ring[rx_id];
> >>> +        first_seg = rsc_entry->fbuf;
> >>> +        rsc_entry->fbuf = NULL;
> >>> +
> >>> +        /*
> >>> +         * If this is the first buffer of the received packet,
> >>> +         * set the pointer to the first mbuf of the packet and
> >>> +         * initialize its context.
> >>> +         * Otherwise, update the total length and the number of
> >>> segments
> >>> +         * of the current scattered packet, and update the pointer to
> >>> +         * the last mbuf of the current packet.
> >>> +         */
> >>> +        if (first_seg == NULL) {
> >>> +            first_seg = rxm;
> >>> +            first_seg->pkt_len = data_len;
> >>> +            first_seg->nb_segs = 1;
> >>> +        } else {
> >>> +            first_seg->pkt_len += data_len;
> >>> +            first_seg->nb_segs++;
> >>> +        }
> >>> +
> >>> +        prev_id = rx_id;
> >>> +        rx_id = next_id;
> >>> +
> >>> +        /*
> >>> +         * If this is not the last buffer of the received packet,
> >>> update
> >>> +         * the pointer to the first mbuf at the NEXTP entry in the
> >>> +         * sw_rsc_ring and continue to parse the RX ring.
> >>> +         */
> >>> +        if (!eop) {
> >>> +            rxm->next = next_rxe->mbuf;
> >>> +            next_rsc_entry->fbuf = first_seg;
> >>> +            goto next_desc;
> >>> +        }
> >>> +
> >>> +        /*
> >>> +         * This is the last buffer of the received packet - return
> >>> +         * the current cluster to the user.
> >>> +         */
> >>> +        rxm->next = NULL;
> >>> +
> >>> +        /* Initialize the first mbuf of the returned packet */
> >>> +        ixgbe_fill_cluster_head_buf(first_seg, &rxd, rxq->port_id,
> >>> +                        staterr);
> >>> +
> >>> +        /* Prefetch data of first segment, if configured to do so. */
> >>> +        rte_packet_prefetch((char *)first_seg->buf_addr +
> >>> +            first_seg->data_off);
> >>> +
> >>> +        /*
> >>> +         * Store the mbuf address into the next entry of the array
> >>> +         * of returned packets.
> >>> +         */
> >>> +        rx_pkts[nb_rx++] = first_seg;
> >>> +    }
> >>> +
> >>> +    /*
> >>> +     * Record index of the next RX descriptor to probe.
> >>> +     */
> >>> +    rxq->rx_tail = rx_id;
> >>> +
> >>> +    /*
> >>> +     * If the number of free RX descriptors is greater than the RX
> >>> free
> >>> +     * threshold of the queue, advance the Receive Descriptor Tail
> >>> (RDT)
> >>> +     * register.
> >>> +     * Update the RDT with the value of the last processed RX
> >>> descriptor
> >>> +     * minus 1, to guarantee that the RDT register is never equal
> >>> to the
> >>> +     * RDH register, which creates a "full" ring situtation from the
> >>> +     * hardware point of view...
> >>> +     */
> >>> +    if (!bulk_alloc && nb_hold > rxq->rx_free_thresh) {
> >>> +        PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_tail=%u "
> >>> +               "nb_hold=%u nb_rx=%u",
> >>> +               rxq->port_id, rxq->queue_id, rx_id, nb_hold, nb_rx);
> >>> +
> >>> +        rte_wmb();
> >>> +        IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr, prev_id);
> >>> +        nb_hold = 0;
> >>> +    }
> >>> +
> >>> +    rxq->nb_rx_hold = nb_hold;
> >>> +    return nb_rx;
> >>> +}
> >>> +
> >>> +uint16_t
> >>> +ixgbe_recv_pkts_lro_single_alloc(void *rx_queue, struct rte_mbuf
> >>> **rx_pkts,
> >>> +                 uint16_t nb_pkts)
> >>> +{
> >>> +    return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, false);
> >>> +}
> >>> +
> >>> +uint16_t
> >>> +ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue, struct rte_mbuf
> >>> **rx_pkts,
> >>> +                   uint16_t nb_pkts)
> >>> +{
> >>> +    return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, true);
> >>> +}
> >>> +
> >>>   uint16_t
> >>>   ixgbe_recv_scattered_pkts(void *rx_queue, struct rte_mbuf **rx_pkts,
> >>>                 uint16_t nb_pkts)
> >>> @@ -2005,6 +2295,31 @@ ixgbe_dev_tx_queue_setup(struct rte_eth_dev
> >>> *dev,
> >>>       return (0);
> >>>   }
> >>>
> >>> +/**
> >>> + * ixgbe_free_rsc_cluster - free the not-yet-completed RSC cluster
> >>> + *
> >>> + * The "next" pointer of the last segment of (not-yet-completed)
> >>> RSC clusters
> >>> + * in the sw_rsc_ring is not set to NULL but rather points to the next
> >>> + * mbuf of this RSC aggregation (that has not been completed yet
> >>> and still
> >>> + * resides on the HW ring). So, instead of calling for
> >>> rte_pktmbuf_free() we
> >>> + * will just free first "nb_segs" segments of the cluster
> >>> explicitly by calling
> >>> + * an rte_pktmbuf_free_seg().
> >>> + *
> >>> + * @m RSC cluster head
> >>> + */
> >>> +static void
> >>> +ixgbe_free_rsc_cluster(struct rte_mbuf *m)
> >>> +{
> >>> +    uint8_t i, nb_segs = m->nb_segs;
> >>> +    struct rte_mbuf *next_seg;
> >>> +
> >>> +    for (i = 0; i < nb_segs; i++) {
> >>> +        next_seg = m->next;
> >>> +        rte_pktmbuf_free_seg(m);
> >>> +        m = next_seg;
> >>> +    }
> >>> +}
> >>> +
> >>>   static void
> >>>   ixgbe_rx_queue_release_mbufs(struct ixgbe_rx_queue *rxq)
> >>>   {
> >>> @@ -2028,6 +2343,13 @@ ixgbe_rx_queue_release_mbufs(struct
> >>> ixgbe_rx_queue *rxq)
> >>>           }
> >>>   #endif
> >>>       }
> >>> +
> >>> +    if (rxq->sw_rsc_ring)
> >>> +        for (i = 0; i < rxq->nb_rx_desc; i++)
> >>> +            if (rxq->sw_rsc_ring[i].fbuf) {
> >>> + ixgbe_free_rsc_cluster(rxq->sw_rsc_ring[i].fbuf);
> >>> +                rxq->sw_rsc_ring[i].fbuf = NULL;
> >>> +            }
> >>>   }
> >>>
> >>>   static void
> >>> @@ -2036,6 +2358,7 @@ ixgbe_rx_queue_release(struct ixgbe_rx_queue
> >>> *rxq)
> >>>       if (rxq != NULL) {
> >>>           ixgbe_rx_queue_release_mbufs(rxq);
> >>>           rte_free(rxq->sw_ring);
> >>> +        rte_free(rxq->sw_rsc_ring);
> >>>           rte_free(rxq);
> >>>       }
> >>>   }
> >>> @@ -2158,6 +2481,7 @@ ixgbe_reset_rx_queue(struct ixgbe_hw *hw,
> >>> struct ixgbe_rx_queue *rxq)
> >>>       rxq->nb_rx_hold = 0;
> >>>       rxq->pkt_first_seg = NULL;
> >>>       rxq->pkt_last_seg = NULL;
> >>> +    rxq->rsc_en = 0;
> >>>   }
> >>>
> >>>   int
> >>> @@ -2172,6 +2496,14 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev
> >>> *dev,
> >>>       struct ixgbe_rx_queue *rxq;
> >>>       struct ixgbe_hw     *hw;
> >>>       uint16_t len;
> >>> +    struct rte_eth_dev_info dev_info = { 0 };
> >>> +    struct rte_eth_rxmode *dev_rx_mode = &dev->data->dev_conf.rxmode;
> >>> +    bool rsc_requested = false;
> >>> +
> >>> +    dev->dev_ops->dev_infos_get(dev, &dev_info);
> >>> +    if ((dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO) &&
> >>> +        dev_rx_mode->enable_lro)
> >>> +        rsc_requested = true;
> >>>
> >>>       PMD_INIT_FUNC_TRACE();
> >>>       hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> >>> @@ -2277,12 +2609,27 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev
> >>> *dev,
> >>>       rxq->sw_ring = rte_zmalloc_socket("rxq->sw_ring",
> >>>                         sizeof(struct ixgbe_rx_entry) * len,
> >>>                         RTE_CACHE_LINE_SIZE, socket_id);
> >>> -    if (rxq->sw_ring == NULL) {
> >>> +    if (!rxq->sw_ring) {
> >>>           ixgbe_rx_queue_release(rxq);
> >>>           return (-ENOMEM);
> >>>       }
> >>> -    PMD_INIT_LOG(DEBUG, "sw_ring=%p hw_ring=%p dma_addr=0x%"PRIx64,
> >>> -             rxq->sw_ring, rxq->rx_ring, rxq->rx_ring_phys_addr);
> >>> +
> >>> +    if (rsc_requested) {
> >>> +        rxq->sw_rsc_ring =
> >>> +            rte_zmalloc_socket("rxq->sw_rsc_ring",
> >>> +                       sizeof(struct ixgbe_rsc_entry) * len,
> >>> +                       RTE_CACHE_LINE_SIZE, socket_id);
> >>> +        if (!rxq->sw_rsc_ring) {
> >>> +            ixgbe_rx_queue_release(rxq);
> >>> +            return (-ENOMEM);
> >>> +        }
> >>> +    } else
> >>> +        rxq->sw_rsc_ring = NULL;
> >>> +
> >>> +    PMD_INIT_LOG(DEBUG, "sw_ring=%p sw_rsc_ring=%p hw_ring=%p "
> >>> +                "dma_addr=0x%"PRIx64,
> >>> +             rxq->sw_ring, rxq->sw_rsc_ring, rxq->rx_ring,
> >>> +             rxq->rx_ring_phys_addr);
> >>>
> >>>       if (!rte_is_power_of_2(nb_desc)) {
> >>>           PMD_INIT_LOG(DEBUG, "queue[%d] doesn't meet Vector Rx "
> >>> @@ -3527,6 +3874,91 @@ ixgbe_dev_mq_tx_configure(struct rte_eth_dev
> >>> *dev)
> >>>       return 0;
> >>>   }
> >>>
> >>> +/**
> >>> + * ixgbe_get_rscctl_maxdesc - Calculate the RSCCTL[n].MAXDESC for PF
> >>> + *
> >>> + * Return the RSCCTL[n].MAXDESC for 82599 and x540 PF devices
> >>> according to the
> >>> + * spec rev. 3.0 chapter 8.2.3.8.13.
> >>> + *
> >>> + * @pool Memory pool of the Rx queue
> >>> + */
> >>> +static inline uint32_t
> >>> +ixgbe_get_rscctl_maxdesc(struct rte_mempool *pool)
> >>> +{
> >>> +    struct rte_pktmbuf_pool_private *mp_priv =
> >>> rte_mempool_get_priv(pool);
> >>> +
> >>> +    /* MAXDESC * SRRCTL.BSIZEPKT must not exceed 64 KB minus one */
> >>> +    uint16_t maxdesc =
> >>> +        IPV4_MAX_PKT_LEN /
> >>> +            (mp_priv->mbuf_data_room_size - RTE_PKTMBUF_HEADROOM);
> >>> +
> >>> +    if (maxdesc >= 16)
> >>> +        return IXGBE_RSCCTL_MAXDESC_16;
> >>> +    else if (maxdesc >= 8)
> >>> +        return IXGBE_RSCCTL_MAXDESC_8;
> >>> +    else if (maxdesc >= 4)
> >>> +        return IXGBE_RSCCTL_MAXDESC_4;
> >>> +    else
> >>> +        return IXGBE_RSCCTL_MAXDESC_1;
> >>> +}
> >>> +
> >>> +/**
> >>> + * ixgbe_set_ivar - Setup the correct IVAR register for a
> >>> particular MSIX
> >>> + * interrupt
> >>> + *
> >>> + * (Taken from FreeBSD tree)
> >>> + * (yes this is all very magic and confusing :)
> >>> + *
> >>> + * @dev port handle
> >>> + * @entry the register array entry
> >>> + * @vector the MSIX vector for this queue
> >>> + * @type RX/TX/MISC
> >>> + */
> >>> +static void
> >>> +ixgbe_set_ivar(struct rte_eth_dev *dev, u8 entry, u8 vector, s8 type)
> >>> +{
> >>> +    struct ixgbe_hw *hw =
> >>> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> >>> +    u32 ivar, index;
> >>> +
> >>> +    vector |= IXGBE_IVAR_ALLOC_VAL;
> >>> +
> >>> +    switch (hw->mac.type) {
> >>> +
> >>> +    case ixgbe_mac_82598EB:
> >>> +        if (type == -1)
> >>> +            entry = IXGBE_IVAR_OTHER_CAUSES_INDEX;
> >>> +        else
> >>> +            entry += (type * 64);
> >>> +        index = (entry >> 2) & 0x1F;
> >>> +        ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(index));
> >>> +        ivar &= ~(0xFF << (8 * (entry & 0x3)));
> >>> +        ivar |= (vector << (8 * (entry & 0x3)));
> >>> +        IXGBE_WRITE_REG(hw, IXGBE_IVAR(index), ivar);
> >>> +        break;
> >>> +
> >>> +    case ixgbe_mac_82599EB:
> >>> +    case ixgbe_mac_X540:
> >>> +        if (type == -1) { /* MISC IVAR */
> >>> +            index = (entry & 1) * 8;
> >>> +            ivar = IXGBE_READ_REG(hw, IXGBE_IVAR_MISC);
> >>> +            ivar &= ~(0xFF << index);
> >>> +            ivar |= (vector << index);
> >>> +            IXGBE_WRITE_REG(hw, IXGBE_IVAR_MISC, ivar);
> >>> +        } else {    /* RX/TX IVARS */
> >>> +            index = (16 * (entry & 1)) + (8 * type);
> >>> +            ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(entry >> 1));
> >>> +            ivar &= ~(0xFF << index);
> >>> +            ivar |= (vector << index);
> >>> +            IXGBE_WRITE_REG(hw, IXGBE_IVAR(entry >> 1), ivar);
> >>> +        }
> >>> +
> >>> +        break;
> >>> +
> >>> +    default:
> >>> +        break;
> >>> +    }
> >>> +}
> >>> +
> >>>   void ixgbe_set_rx_function(struct rte_eth_dev *dev)
> >>>   {
> >>>       struct ixgbe_hw *hw =
> >>> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> >>> @@ -3545,7 +3977,24 @@ void ixgbe_set_rx_function(struct rte_eth_dev
> >>> *dev)
> >>>           hw->rx_vec_allowed = false;
> >>>       }
> >>>
> >>> -    if (dev->data->scattered_rx) {
> >>> +    /*
> >>> +     * Initialize the appropriate LRO callback.
> >>> +     *
> >>> +     * If all queues satisfy the bulk allocation preconditions
> >>> +     * (hw->rx_bulk_alloc_allowed is TRUE) then we may use bulk
> >>> allocation.
> >>> +     * Otherwise use a single allocation version.
> >>> +     */
> >>> +    if (dev->data->lro) {
> >>> +        if (hw->rx_bulk_alloc_allowed) {
> >>> +            PMD_INIT_LOG(INFO, "LRO is requested. Using a bulk "
> >>> +                       "allocation version");
> >>> +            dev->rx_pkt_burst = ixgbe_recv_pkts_lro_bulk_alloc;
> >>> +        } else {
> >>> +            PMD_INIT_LOG(INFO, "LRO is requested. Using a single "
> >>> +                       "allocation version");
> >>> +            dev->rx_pkt_burst = ixgbe_recv_pkts_lro_single_alloc;
> >>> +        }
> >>> +    } else if (dev->data->scattered_rx) {
> >>>           /*
> >>>            * Set the non-LRO scattered callback: there are Vector and
> >>>            * single allocation versions.
> >>> @@ -3595,6 +4044,149 @@ void ixgbe_set_rx_function(struct
> >>> rte_eth_dev *dev)
> >>>       }
> >>>   }
> >>>
> >>> +/**
> >>> + * ixgbe_set_rsc - configure RSC related port HW registers
> >>> + *
> >>> + * Configures the port's RSC related registers according to the
> >>> 4.6.7.2 chapter
> >>> + * of 82599 Spec (x540 configuration is virtually the same).
> >>> + *
> >>> + * @dev port handle
> >>> + *
> >>> + * Returns 0 in case of success or a non-zero error code
> >>> + */
> >>> +static int
> >>> +ixgbe_set_rsc(struct rte_eth_dev *dev)
> >>> +{
> >>> +    struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
> >>> +    struct ixgbe_hw *hw =
> >>> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> >>> +    struct rte_eth_dev_info dev_info = { 0 };
> >>> +    bool rsc_capable = false;
> >>> +    uint16_t i;
> >>> +    uint32_t rdrxctl;
> >>> +
> >>> +    /* Sanity check */
> >>> +    dev->dev_ops->dev_infos_get(dev, &dev_info);
> >>> +    if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO)
> >>> +        rsc_capable = true;
> >>> +
> >>> +    if (!rsc_capable && rx_conf->enable_lro) {
> >>> +        PMD_INIT_LOG(CRIT, "LRO is requested on HW that doesn't "
> >>> +                   "support it");
> >>> +        return -EINVAL;
> >>> +    }
> >>> +
> >>> +    /* RSC global configuration (chapter 4.6.7.2.1 of 82599 Spec) */
> >>> +
> >>> +    if (!rx_conf->hw_strip_crc && rx_conf->enable_lro) {
> >>> +        /*
> >>> +         * According to chapter of 4.6.7.2.1 of the Spec Rev.
> >>> +         * 3.0 RSC configuration requires HW CRC stripping being
> >>> +         * enabled. If user requested both HW CRC stripping off
> >>> +         * and RSC on - return an error.
> >>> +         */
> >>> +        PMD_INIT_LOG(CRIT, "LRO can't be enabled when HW CRC "
> >>> +                    "is disabled");
> >>> +        return -EINVAL;
> >>> +    }
> >>> +
> >>> +    /* RFCTL configuration  */
> >>> +    if (rsc_capable) {
> >>> +        uint32_t rfctl = IXGBE_READ_REG(hw, IXGBE_RFCTL);
> >>> +        if (rx_conf->enable_lro)
> >>> +            /*
> >>> +             * Since NFS packets coalescing is not supported - clear
> >>> +             * RFCTL.NFSW_DIS and RFCTL.NFSR_DIS when RSC is
> >>> +             * enabled.
> >>> +             */
> >>> +            rfctl &= ~(IXGBE_RFCTL_RSC_DIS | IXGBE_RFCTL_NFSW_DIS |
> >>> +                   IXGBE_RFCTL_NFSR_DIS);
> >>> +        else
> >>> +            rfctl |= IXGBE_RFCTL_RSC_DIS;
> >>> +
> >>> +        IXGBE_WRITE_REG(hw, IXGBE_RFCTL, rfctl);
> >>> +    }
> >>> +
> >>> +    /* If LRO hasn't been requested - we are done here. */
> >>> +    if (!rx_conf->enable_lro)
> >>> +        return 0;
> >>> +
> >>> +    /* Set RDRXCTL.RSCACKC bit */
> >>> +    rdrxctl = IXGBE_READ_REG(hw, IXGBE_RDRXCTL);
> >>> +    rdrxctl |= IXGBE_RDRXCTL_RSCACKC;
> >>> +    IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
> >>> +
> >>> +    /* Per-queue RSC configuration (chapter 4.6.7.2.2 of 82599
> >>> Spec) */
> >>> +    for (i = 0; i < dev->data->nb_rx_queues; i++) {
> >>> +        struct ixgbe_rx_queue *rxq = dev->data->rx_queues[i];
> >>> +        uint32_t srrctl =
> >>> +            IXGBE_READ_REG(hw, IXGBE_SRRCTL(rxq->reg_idx));
> >>> +        uint32_t rscctl =
> >>> +            IXGBE_READ_REG(hw, IXGBE_RSCCTL(rxq->reg_idx));
> >>> +        uint32_t psrtype =
> >>> +            IXGBE_READ_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx));
> >>> +        uint32_t eitr =
> >>> +            IXGBE_READ_REG(hw, IXGBE_EITR(rxq->reg_idx));
> >>> +
> >>> +        /*
> >>> +         * ixgbe PMD doesn't support header-split at the moment.
> >>> +         *
> >>> +         * Following the 4.6.7.2.1 chapter of the 82599/x540
> >>> +         * Spec if RSC is enabled the SRRCTL[n].BSIZEHEADER
> >>> +         * should be configured even if header split is not
> >>> +         * enabled. We will configure it 128 bytes following the
> >>> +         * recommendation in the spec.
> >>> +         */
> >>> +        srrctl &= ~IXGBE_SRRCTL_BSIZEHDR_MASK;
> >>> +        srrctl |= (128 << IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT) &
> >>> +                        IXGBE_SRRCTL_BSIZEHDR_MASK;
> >>> +
> >>> +        /*
> >>> +         * TODO: Consider setting the Receive Descriptor Minimum
> >>> +         * Threshold Size for an RSC case. This is not an obviously
> >>> +         * beneficiary option but the one worth considering...
> >>> +         */
> >>> +
> >>> +        rscctl |= IXGBE_RSCCTL_RSCEN;
> >>> +        rscctl |= ixgbe_get_rscctl_maxdesc(rxq->mb_pool);
> >>> +        psrtype |= IXGBE_PSRTYPE_TCPHDR;
> >>> +
> >>> +        /*
> >>> +         * RSC: Set ITR interval corresponding to 2K ints/s.
> >>> +         *
> >>> +         * Full-sized RSC aggregations for a 10Gb/s link will
> >>> +         * arrive at about 20K aggregation/s rate.
> >>> +         *
> >>> +         * 2K inst/s rate will make only 10% of the
> >>> +         * aggregations to be closed due to the interrupt timer
> >>> +         * expiration for a streaming at wire-speed case.
> >>> +         *
> >>> +         * For a sparse streaming case this setting will yield
> >>> +         * at most 500us latency for a single RSC aggregation.
> >>> +         */
> >>> +        eitr &= ~IXGBE_EITR_ITR_INT_MASK;
> >>> +        eitr |= IXGBE_EITR_INTERVAL_US(500) | IXGBE_EITR_CNT_WDIS;
> >>> +
> >>> +        IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
> >>> +        IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(rxq->reg_idx), rscctl);
> >>> +        IXGBE_WRITE_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx), psrtype);
> >>> +        IXGBE_WRITE_REG(hw, IXGBE_EITR(rxq->reg_idx), eitr);
> >>> +
> >>> +        /*
> >>> +         * RSC requires the mapping of the queue to the
> >>> +         * interrupt vector.
> >>> +         */
> >>> +        ixgbe_set_ivar(dev, rxq->reg_idx, i, 0);
> >>> +
> >>> +        rxq->rsc_en = 1;
> >>> +    }
> >>> +
> >>> +    dev->data->lro = 1;
> >>> +
> >>> +    PMD_INIT_LOG(INFO, "enabling LRO mode");
> >>> +
> >>> +    return 0;
> >>> +}
> >>> +
> >>>   /*
> >>>    * Initializes Receive Unit.
> >>>    */
> >>> @@ -3615,6 +4207,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
> >>>       uint16_t buf_size;
> >>>       uint16_t i;
> >>>       struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
> >>> +    int rc;
> >>>
> >>>       PMD_INIT_FUNC_TRACE();
> >>>       hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> >>> @@ -3724,6 +4317,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
> >>>                          RTE_PKTMBUF_HEADROOM);
> >>>           srrctl |= ((buf_size >> IXGBE_SRRCTL_BSIZEPKT_SHIFT) &
> >>>                  IXGBE_SRRCTL_BSIZEPKT_MASK);
> >>> +
> >>>           IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
> >>>
> >>>           buf_size = (uint16_t) ((srrctl &
> >>> IXGBE_SRRCTL_BSIZEPKT_MASK) <<
> >>> @@ -3738,8 +4332,6 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
> >>>       if (rx_conf->enable_scatter)
> >>>           dev->data->scattered_rx = 1;
> >>>
> >>> -    ixgbe_set_rx_function(dev);
> >>> -
> >>>       /*
> >>>        * Device configured with multiple RX queues.
> >>>        */
> >>> @@ -3770,6 +4362,12 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
> >>>           IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
> >>>       }
> >>>
> >>> +    rc = ixgbe_set_rsc(dev);
> >>> +    if (rc)
> >>> +        return rc;
> >>> +
> >>> +    ixgbe_set_rx_function(dev);
> >>> +
> >>>       return 0;
> >>>   }
> >>>
> >>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
> >>> b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
> >>> index 3937cf6..120bbbd 100644
> >>> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
> >>> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
> >>> @@ -79,6 +79,10 @@ struct ixgbe_rx_entry {
> >>>       struct rte_mbuf *mbuf; /**< mbuf associated with RX
> >>> descriptor. */
> >>>   };
> >>>
> >>> +struct ixgbe_rsc_entry {
> >>> +    struct rte_mbuf *fbuf; /**< First segment of the fragmented
> >>> packet. */
> >>> +};
> >>> +
> >>>   /**
> >>>    * Structure associated with each descriptor of the TX ring of a
> >>> TX queue.
> >>>    */
> >>> @@ -105,6 +109,7 @@ struct ixgbe_rx_queue {
> >>>       volatile uint32_t   *rdt_reg_addr; /**< RDT register address. */
> >>>       volatile uint32_t   *rdh_reg_addr; /**< RDH register address. */
> >>>       struct ixgbe_rx_entry *sw_ring; /**< address of RX software
> >>> ring. */
> >>> +    struct ixgbe_rsc_entry *sw_rsc_ring; /**< address of RSC
> >>> software ring. */
> >>>       struct rte_mbuf *pkt_first_seg; /**< First segment of current
> >>> packet. */
> >>>       struct rte_mbuf *pkt_last_seg; /**< Last segment of current
> >>> packet. */
> >>>       uint64_t            mbuf_initializer; /**< value to init mbufs */
> >>> @@ -126,6 +131,7 @@ struct ixgbe_rx_queue {
> >>>       uint8_t             port_id;  /**< Device port identifier. */
> >>>       uint8_t             crc_len;  /**< 0 if CRC stripped, 4
> >>> otherwise. */
> >>>       uint8_t             drop_en;  /**< If not 0, set
> >>> SRRCTL.Drop_En. */
> >>> +    uint8_t             rsc_en;   /**< If not 0, RSC is enabled. */
> >>>       uint8_t             rx_deferred_start; /**< not in global dev
> >>> start. */
> >>>   #ifdef RTE_LIBRTE_IXGBE_RX_ALLOW_BULK_ALLOC
> >>>       /** need to alloc dummy mbuf, for wraparound when scanning hw
> >>> ring */
> >>> --
> >>> 2.1.0
> >

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
  2015-03-31 10:25 [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support Ananyev, Konstantin
@ 2015-03-31 11:40 ` Vlad Zolotarov
  0 siblings, 0 replies; 6+ messages in thread
From: Vlad Zolotarov @ 2015-03-31 11:40 UTC (permalink / raw)
  To: Ananyev, Konstantin, dev



On 03/31/15 13:25, Ananyev, Konstantin wrote:
>
>> -----Original Message-----
>> From: Vlad Zolotarov [mailto:vladz@cloudius-systems.com]
>> Sent: Monday, March 30, 2015 4:57 PM
>> To: Ananyev, Konstantin; dev@dpdk.org
>> Subject: Re: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
>>
>>
>>
>> On 03/30/15 18:37, Vlad Zolotarov wrote:
>>>
>>> On 03/30/15 17:18, Ananyev, Konstantin wrote:
>>>> Hi Vlad,
>>>>
>>>>> -----Original Message-----
>>>>> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Vlad Zolotarov
>>>>> Sent: Wednesday, March 18, 2015 5:52 PM
>>>>> To: dev@dpdk.org
>>>>> Subject: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
>>>>>
>>>>>       - Only x540 and 82599 devices support LRO.
>>>>>       - Add the appropriate HW configuration.
>>>>>       - Add RSC aware rx_pkt_burst() handlers:
>>>>>          - Implemented bulk allocation and non-bulk allocation versions.
>>>>>          - Add LRO-specific fields to rte_eth_rxmode, to
>>>>> rte_eth_dev_data
>>>>>            and to ixgbe_rx_queue.
>>>>>          - Use the appropriate handler when LRO is requested.
>>>>>
>>>>> Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
>>>>> ---
>>>>> New in v8:
>>>>>      - Took the RSC configuration code from ixgbe_dev_rx_init() into
>>>>> a separate
>>>>>        function - ixgbe_set_rsc().
>>>>>      - Added some missing macros for HW configuration.
>>>>>      - Styling adjustments:
>>>>>         - Functions names.
>>>>>         - Functions descriptions.
>>>>>      - Reworked the ixgbe_free_rsc_cluster() code to make it more
>>>>> readable.
>>>>>      - Kill the HEADER_SPLIT flow in ixgbe_set_rsc() since it's not
>>>>> supported by
>>>>>        ixgbe PMD.
>>>>>
>>>>> New in v7:
>>>>>      - Free not-yet-completed RSC aggregations in rte_eth_dev_stop()
>>>>> flow.
>>>>>      - Reset the sw_ring[].mbuf entry in a bulk allocation case.
>>>>>        This is needed for ixgbe_rx_queue_release_mbufs().
>>>>>      - _recv_pkts_lro(): added the missing memory barrier before RDT
>>>>> update in a
>>>>>        non-bulk allocation case.
>>>>>      - Don't allow RSC when device is configured in an SR-IOV mode.
>>>>>
>>>>> New in v5:
>>>>>      - Put the RTE_ETHDEV_HAS_LRO_SUPPORT definition at the beginning
>>>>> of rte_ethdev.h.
>>>>>      - Removed the "TODO: Remove me" comment near
>>>>> RTE_ETHDEV_HAS_LRO_SUPPORT.
>>>>>
>>>>> New in v4:
>>>>>      - Define RTE_ETHDEV_HAS_LRO_SUPPORT in rte_ethdev.h instead of
>>>>>        RTE_ETHDEV_LRO_SUPPORT defined in config/common_linuxapp.
>>>>>
>>>>> New in v2:
>>>>>      - Removed rte_eth_dev_data.lro_bulk_alloc.
>>>>>      - Fixed a few styling and spelling issues.
>>>>> ---
>>>>>    lib/librte_ether/rte_ethdev.h           |   9 +-
>>>>>    lib/librte_net/rte_ip.h                 |   3 +
>>>>>    lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h |   6 +
>>>>>    lib/librte_pmd_ixgbe/ixgbe_ethdev.c     |  11 +
>>>>>    lib/librte_pmd_ixgbe/ixgbe_ethdev.h     |   5 +
>>>>>    lib/librte_pmd_ixgbe/ixgbe_rxtx.c       | 610
>>>>> +++++++++++++++++++++++++++++++-
>>>>>    lib/librte_pmd_ixgbe/ixgbe_rxtx.h       |   6 +
>>>>>    7 files changed, 642 insertions(+), 8 deletions(-)
>>>>>
>>>>> diff --git a/lib/librte_ether/rte_ethdev.h
>>>>> b/lib/librte_ether/rte_ethdev.h
>>>>> index 21aa359..61dc49a 100644
>>>>> --- a/lib/librte_ether/rte_ethdev.h
>>>>> +++ b/lib/librte_ether/rte_ethdev.h
>>>>> @@ -172,6 +172,9 @@ extern "C" {
>>>>>
>>>>>    #include <stdint.h>
>>>>>
>>>>> +/* Use this macro to check if LRO API is supported */
>>>>> +#define RTE_ETHDEV_HAS_LRO_SUPPORT
>>>>> +
>>>>>    #include <rte_log.h>
>>>>>    #include <rte_interrupts.h>
>>>>>    #include <rte_pci.h>
>>>>> @@ -320,14 +323,15 @@ struct rte_eth_rxmode {
>>>>>        enum rte_eth_rx_mq_mode mq_mode;
>>>>>        uint32_t max_rx_pkt_len;  /**< Only used if jumbo_frame
>>>>> enabled. */
>>>>>        uint16_t split_hdr_size;  /**< hdr buf size (header_split
>>>>> enabled).*/
>>>>> -    uint8_t header_split : 1, /**< Header Split enable. */
>>>>> +    uint16_t header_split : 1, /**< Header Split enable. */
>>>>>            hw_ip_checksum   : 1, /**< IP/UDP/TCP checksum offload
>>>>> enable. */
>>>>>            hw_vlan_filter   : 1, /**< VLAN filter enable. */
>>>>>            hw_vlan_strip    : 1, /**< VLAN strip enable. */
>>>>>            hw_vlan_extend   : 1, /**< Extended VLAN enable. */
>>>>>            jumbo_frame      : 1, /**< Jumbo Frame Receipt enable. */
>>>>>            hw_strip_crc     : 1, /**< Enable CRC stripping by
>>>>> hardware. */
>>>>> -        enable_scatter   : 1; /**< Enable scatter packets rx
>>>>> handler */
>>>>> +        enable_scatter   : 1, /**< Enable scatter packets rx
>>>>> handler */
>>>>> +        enable_lro       : 1; /**< Enable LRO */
>>>>>    };
>>>>>
>>>>>    /**
>>>>> @@ -1515,6 +1519,7 @@ struct rte_eth_dev_data {
>>>>>        uint8_t port_id;           /**< Device [external] port
>>>>> identifier. */
>>>>>        uint8_t promiscuous   : 1, /**< RX promiscuous mode ON(1) /
>>>>> OFF(0). */
>>>>>            scattered_rx : 1,  /**< RX of scattered packets is ON(1) /
>>>>> OFF(0) */
>>>>> +        lro          : 1,  /**< RX LRO is ON(1) / OFF(0) */
>>>>>            all_multicast : 1, /**< RX all multicast mode ON(1) /
>>>>> OFF(0). */
>>>>>            dev_started : 1;   /**< Device state: STARTED(1) /
>>>>> STOPPED(0). */
>>>>>    };
>>>>> diff --git a/lib/librte_net/rte_ip.h b/lib/librte_net/rte_ip.h
>>>>> index 64935d9..74c9ced 100644
>>>>> --- a/lib/librte_net/rte_ip.h
>>>>> +++ b/lib/librte_net/rte_ip.h
>>>>> @@ -110,6 +110,9 @@ struct ipv4_hdr {
>>>>>                           (((c) & 0xff) << 8)  | \
>>>>>                           ((d) & 0xff))
>>>>>
>>>>> +/** Maximal IPv4 packet length (including a header) */
>>>>> +#define IPV4_MAX_PKT_LEN        65535
>>>>> +
>>>>>    /** Internet header length mask for version_ihl field */
>>>>>    #define IPV4_HDR_IHL_MASK    (0x0f)
>>>>>    /**
>>>>> diff --git a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
>>>>> b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
>>>>> index 9a66370..4998627 100644
>>>>> --- a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
>>>>> +++ b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
>>>>> @@ -234,8 +234,14 @@ struct ixgbe_thermal_sensor_data {
>>>>>    #define IXGBE_EITR(_i)        (((_i) <= 23) ? (0x00820 + ((_i) *
>>>>> 4)) : \
>>>>>                     (0x012300 + (((_i) - 24) * 4)))
>>>>>    #define IXGBE_EITR_ITR_INT_MASK    0x00000FF8
>>>>> +#define IXGBE_EITR_ITR_INT_SHIFT 3
>>>>>    #define IXGBE_EITR_LLI_MOD    0x00008000
>>>>>    #define IXGBE_EITR_CNT_WDIS    0x80000000
>>>>> +/* EITR Inteval is in 2048ns uinits for 1G and 10G link */
>>>>> +#define IXGBE_EITR_INTERVAL_UNIT_NS    2048
>>>> Why is that? Why not just 2us as 82599 spec says?
>>>> And then:
>>>> +#define IXGBE_EITR_INTERVAL_US(us) (((us) /
>>>> IXGBE_EITR_INTERVAL_UNIT_US << IXGBE_EITR_ITR_INT_SHIFT) &
>>>> IXGBE_EITR_ITR_INT_MASK)
>>>> ?
>>> Because spec doesn't say 2us but rather 2.048us - see 8.2.4.5.16
>>> chapter of x540 spec.
>> The most confusing part is that 82599 Rev. 3.0 spec does say so.
> I see what you mean now.
> Indeed that's a bit strange that in 82599 and X540 spec ITR_Interval units are different.
> We sent a question about this to HW guys, but don't know when there will be an answer.
> I suppose we can stick with 2.048 us case for now.
>  From my understanding, even if 82599 uses 2us the difference in max timeout would be pretty small: 500 us vs 488 us
> and shouldn't cause any performance drop.
> I wonder did try your LRO latest changes on 82599?
> If yes, did you see any difference in performance vs previous version, when hardcoded value for 2us was used?

U are right about the negligible difference even if it exists (if it's 
this is not a small mistake in a 82599 spec).
Unfortunately all 10G Intel NICs we have in our lab are x540 NICs. 
However I doubt that I could have noticed the difference even if I had 
82599 NICs. This is because I don't have a too sophisticated LRO test 
suite here and I only checked LRO's basic functionality with a 
multi-socket TCP streaming test. With this scenario the timer above is 
going to influence only about 10% of the aggregations (like I explained 
in the code) and if the latency drops to 488us it's going to be 10.25% 
of the aggregations. So, I doubt that influence of this difference on 
the performance is going to be easily separated from the statistics 
noise... ;)


> Konstantin
>
>> The  x540 spec I have is dated by March 2014 and 82599 spec is dated by
>> November 2014 but according to changelog EITR description has never been
>> updated. Therefore I conclude that the more recent device spec (x540)
>> holds the most up to date content.
>>
>> Pls., confirm.
>>
>> thanks,
>> vlad
>>
>>>>> +#define IXGBE_EITR_INTERVAL_US(us)    \
>>>>> +   (((us) * 1000 / IXGBE_EITR_INTERVAL_UNIT_NS <<
>>>>> IXGBE_EITR_ITR_INT_SHIFT) & \
>>>>> +        IXGBE_EITR_ITR_INT_MASK)
>>>> Unfortunately we are not supposed to change files under ixgbe
>>>> subfirectory (except ixgbe_osdep.*).
>>>> These files comes from ixgbe shared code and we treat them as read-only.
>>>> You need to move these new macros you added into ixgbe_ethedev.h.
>>> Aha... Ok. No problem.
>>>
>>>> All other things look good to me.
>>>> Konstantin
>>>>
>>>>>    #define IXGBE_IVAR(_i)        (0x00900 + ((_i) * 4)) /* 24 at
>>>>> 0x900-0x960 */
>>>>>    #define IXGBE_IVAR_MISC        0x00A00 /* misc MSI-X interrupt
>>>>> causes */
>>>>>    #define IXGBE_EITRSEL        0x00894
>>>>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>>>>> b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>>>>> index 92d75db..923692e 100644
>>>>> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>>>>> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>>>>> @@ -1645,6 +1645,7 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
>>>>>
>>>>>        /* Clear stored conf */
>>>>>        dev->data->scattered_rx = 0;
>>>>> +    dev->data->lro = 0;
>>>>>
>>>>>        /* Clear recorded link status */
>>>>>        memset(&link, 0, sizeof(link));
>>>>> @@ -2013,6 +2014,16 @@ ixgbe_dev_info_get(struct rte_eth_dev *dev,
>>>>> struct rte_eth_dev_info *dev_info)
>>>>>            DEV_RX_OFFLOAD_IPV4_CKSUM |
>>>>>            DEV_RX_OFFLOAD_UDP_CKSUM  |
>>>>>            DEV_RX_OFFLOAD_TCP_CKSUM;
>>>>> +
>>>>> +    /*
>>>>> +     * RSC is only supported by 82599 and x540 PF devices in a
>>>>> non-SR-IOV
>>>>> +     * mode.
>>>>> +     */
>>>>> +    if ((hw->mac.type == ixgbe_mac_82599EB ||
>>>>> +         hw->mac.type == ixgbe_mac_X540) &&
>>>>> +        !RTE_ETH_DEV_SRIOV(dev).active)
>>>>> +        dev_info->rx_offload_capa |= DEV_RX_OFFLOAD_TCP_LRO;
>>>>> +
>>>>>        dev_info->tx_offload_capa =
>>>>>            DEV_TX_OFFLOAD_VLAN_INSERT |
>>>>>            DEV_TX_OFFLOAD_IPV4_CKSUM  |
>>>>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>>>>> b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>>>>> index ffe3471..7050340 100644
>>>>> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>>>>> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>>>>> @@ -344,6 +344,11 @@ uint16_t ixgbe_recv_pkts(void *rx_queue, struct
>>>>> rte_mbuf **rx_pkts,
>>>>>    uint16_t ixgbe_recv_scattered_pkts(void *rx_queue,
>>>>>            struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
>>>>>
>>>>> +uint16_t ixgbe_recv_pkts_lro_single_alloc(void *rx_queue,
>>>>> +        struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
>>>>> +uint16_t ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue,
>>>>> +        struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
>>>>> +
>>>>>    uint16_t ixgbe_xmit_pkts(void *tx_queue, struct rte_mbuf **tx_pkts,
>>>>>            uint16_t nb_pkts);
>>>>>
>>>>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
>>>>> b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
>>>>> index a08ae6a..daa4c45 100644
>>>>> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
>>>>> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
>>>>> @@ -70,6 +70,7 @@
>>>>>    #include <rte_sctp.h>
>>>>>    #include <rte_string_fns.h>
>>>>>    #include <rte_errno.h>
>>>>> +#include <rte_ip.h>
>>>>>
>>>>>    #include "ixgbe_logs.h"
>>>>>    #include "ixgbe/ixgbe_api.h"
>>>>> @@ -1422,6 +1423,295 @@ ixgbe_fill_cluster_head_buf(
>>>>>        }
>>>>>    }
>>>>>
>>>>> +/**
>>>>> + * ixgbe_recv_pkts_lro - receive handler for and LRO case.
>>>>> + *
>>>>> + * @rx_queue Rx queue handle
>>>>> + * @rx_pkts table of received packets
>>>>> + * @nb_pkts size of rx_pkts table
>>>>> + * @bulk_alloc if TRUE bulk allocation is used for a HW ring refilling
>>>>> + *
>>>>> + * Handles the Rx HW ring completions when RSC feature is
>>>>> configured. Uses an
>>>>> + * additional ring of ixgbe_rsc_entry's that will hold the relevant
>>>>> RSC info.
>>>>> + *
>>>>> + * We use the same logic as in Lunux and in FreeBSD ixgbe drivers:
>>>>> + * 1) When non-EOP RSC completion arrives:
>>>>> + *    a) Update the HEAD of the current RSC aggregation cluster
>>>>> with the new
>>>>> + *       segment's data length.
>>>>> + *    b) Set the "next" pointer of the current segment to point to
>>>>> the segment
>>>>> + *       at the NEXTP index.
>>>>> + *    c) Pass the HEAD of RSC aggregation cluster on to the next
>>>>> NEXTP entry
>>>>> + *       in the sw_rsc_ring.
>>>>> + * 2) When EOP arrives we just update the cluster's total length
>>>>> and offload
>>>>> + *    flags and deliver the cluster up to the upper layers. In our
>>>>> case - put it
>>>>> + *    in the rx_pkts table.
>>>>> + *
>>>>> + * Returns the number of received packets/clusters (according to
>>>>> the "bulk
>>>>> + * receive" interface).
>>>>> + */
>>>>> +static inline uint16_t
>>>>> +ixgbe_recv_pkts_lro(void *rx_queue, struct rte_mbuf **rx_pkts,
>>>>> uint16_t nb_pkts,
>>>>> +            bool bulk_alloc)
>>>>> +{
>>>>> +    struct ixgbe_rx_queue *rxq = rx_queue;
>>>>> +    volatile union ixgbe_adv_rx_desc *rx_ring = rxq->rx_ring;
>>>>> +    struct ixgbe_rx_entry *sw_ring = rxq->sw_ring;
>>>>> +    struct ixgbe_rsc_entry *sw_rsc_ring = rxq->sw_rsc_ring;
>>>>> +    uint16_t rx_id = rxq->rx_tail;
>>>>> +    uint16_t nb_rx = 0;
>>>>> +    uint16_t nb_hold = rxq->nb_rx_hold;
>>>>> +    uint16_t prev_id = rxq->rx_tail;
>>>>> +
>>>>> +    while (nb_rx < nb_pkts) {
>>>>> +        bool eop;
>>>>> +        struct ixgbe_rx_entry *rxe;
>>>>> +        struct ixgbe_rsc_entry *rsc_entry;
>>>>> +        struct ixgbe_rsc_entry *next_rsc_entry;
>>>>> +        struct ixgbe_rx_entry *next_rxe;
>>>>> +        struct rte_mbuf *first_seg;
>>>>> +        struct rte_mbuf *rxm;
>>>>> +        struct rte_mbuf *nmb;
>>>>> +        union ixgbe_adv_rx_desc rxd;
>>>>> +        uint16_t data_len;
>>>>> +        uint16_t next_id;
>>>>> +        volatile union ixgbe_adv_rx_desc *rxdp;
>>>>> +        uint32_t staterr;
>>>>> +
>>>>> +next_desc:
>>>>> +        /*
>>>>> +         * The code in this whole file uses the volatile pointer to
>>>>> +         * ensure the read ordering of the status and the rest of the
>>>>> +         * descriptor fields (on the compiler level only!!!). This
>>>>> is so
>>>>> +         * UGLY - why not to just use the compiler barrier instead?
>>>>> DPDK
>>>>> +         * even has the rte_compiler_barrier() for that.
>>>>> +         *
>>>>> +         * But most importantly this is just wrong because this
>>>>> doesn't
>>>>> +         * ensure memory ordering in a general case at all. For
>>>>> +         * instance, DPDK is supposed to work on Power CPUs where
>>>>> +         * compiler barrier may just not be enough!
>>>>> +         *
>>>>> +         * I tried to write only this function properly to have a
>>>>> +         * starting point (as a part of an LRO/RSC series) but the
>>>>> +         * compiler cursed at me when I tried to cast away the
>>>>> +         * "volatile" from rx_ring (yes, it's volatile too!!!). So,
>>>>> I'm
>>>>> +         * keeping it the way it is for now.
>>>>> +         *
>>>>> +         * The code in this file is broken in so many other places and
>>>>> +         * will just not work on a big endian CPU anyway therefore the
>>>>> +         * lines below will have to be revisited together with the
>>>>> rest
>>>>> +         * of the ixgbe PMD.
>>>>> +         *
>>>>> +         * TODO:
>>>>> +         *    - Get rid of "volatile" crap and let the compiler do its
>>>>> +         *      job.
>>>>> +         *    - Use the proper memory barrier (rte_rmb()) to ensure
>>>>> the
>>>>> +         *      memory ordering below.
>>>>> +         */
>>>>> +        rxdp = &rx_ring[rx_id];
>>>>> +        staterr = rte_le_to_cpu_32(rxdp->wb.upper.status_error);
>>>>> +
>>>>> +        if (!(staterr & IXGBE_RXDADV_STAT_DD))
>>>>> +            break;
>>>>> +
>>>>> +        rxd = *rxdp;
>>>>> +
>>>>> +        PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_id=%u "
>>>>> +                  "staterr=0x%x data_len=%u",
>>>>> +               rxq->port_id, rxq->queue_id, rx_id, staterr,
>>>>> +               rte_le_to_cpu_16(rxd.wb.upper.length));
>>>>> +
>>>>> +        if (!bulk_alloc) {
>>>>> +            nmb = rte_rxmbuf_alloc(rxq->mb_pool);
>>>>> +            if (nmb == NULL) {
>>>>> +                PMD_RX_LOG(DEBUG, "RX mbuf alloc failed "
>>>>> +                          "port_id=%u queue_id=%u",
>>>>> +                       rxq->port_id, rxq->queue_id);
>>>>> +
>>>>> +                rte_eth_devices[rxq->port_id].data->
>>>>> +                            rx_mbuf_alloc_failed++;
>>>>> +                break;
>>>>> +            }
>>>>> +        } else if (nb_hold > rxq->rx_free_thresh) {
>>>>> +            uint16_t next_rdt = rxq->rx_free_trigger;
>>>>> +
>>>>> +            if (!ixgbe_rx_alloc_bufs(rxq, false)) {
>>>>> +                rte_wmb();
>>>>> +                IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr,
>>>>> +                            next_rdt);
>>>>> +                nb_hold -= rxq->rx_free_thresh;
>>>>> +            } else {
>>>>> +                PMD_RX_LOG(DEBUG, "RX bulk alloc failed "
>>>>> +                          "port_id=%u queue_id=%u",
>>>>> +                       rxq->port_id, rxq->queue_id);
>>>>> +
>>>>> +                rte_eth_devices[rxq->port_id].data->
>>>>> +                            rx_mbuf_alloc_failed++;
>>>>> +                break;
>>>>> +            }
>>>>> +        }
>>>>> +
>>>>> +        nb_hold++;
>>>>> +        rxe = &sw_ring[rx_id];
>>>>> +        eop = staterr & IXGBE_RXDADV_STAT_EOP;
>>>>> +
>>>>> +        next_id = rx_id + 1;
>>>>> +        if (next_id == rxq->nb_rx_desc)
>>>>> +            next_id = 0;
>>>>> +
>>>>> +        /* Prefetch next mbuf while processing current one. */
>>>>> +        rte_ixgbe_prefetch(sw_ring[next_id].mbuf);
>>>>> +
>>>>> +        /*
>>>>> +         * When next RX descriptor is on a cache-line boundary,
>>>>> +         * prefetch the next 4 RX descriptors and the next 4 pointers
>>>>> +         * to mbufs.
>>>>> +         */
>>>>> +        if ((next_id & 0x3) == 0) {
>>>>> +            rte_ixgbe_prefetch(&rx_ring[next_id]);
>>>>> +            rte_ixgbe_prefetch(&sw_ring[next_id]);
>>>>> +        }
>>>>> +
>>>>> +        rxm = rxe->mbuf;
>>>>> +
>>>>> +        if (!bulk_alloc) {
>>>>> +            __le64 dma =
>>>>> + rte_cpu_to_le_64(RTE_MBUF_DATA_DMA_ADDR_DEFAULT(nmb));
>>>>> +            /*
>>>>> +             * Update RX descriptor with the physical address of the
>>>>> +             * new data buffer of the new allocated mbuf.
>>>>> +             */
>>>>> +            rxe->mbuf = nmb;
>>>>> +
>>>>> +            rxm->data_off = RTE_PKTMBUF_HEADROOM;
>>>>> +            rxdp->read.hdr_addr = dma;
>>>>> +            rxdp->read.pkt_addr = dma;
>>>>> +        } else
>>>>> +            rxe->mbuf = NULL;
>>>>> +
>>>>> +        /*
>>>>> +         * Set data length & data buffer address of mbuf.
>>>>> +         */
>>>>> +        data_len = rte_le_to_cpu_16(rxd.wb.upper.length);
>>>>> +        rxm->data_len = data_len;
>>>>> +
>>>>> +        if (!eop) {
>>>>> +            uint16_t nextp_id;
>>>>> +            /*
>>>>> +             * Get next descriptor index:
>>>>> +             *  - For RSC it's in the NEXTP field.
>>>>> +             *  - For a scattered packet - it's just a following
>>>>> +             *    descriptor.
>>>>> +             */
>>>>> +            if (ixgbe_rsc_count(&rxd))
>>>>> +                nextp_id =
>>>>> +                    (staterr & IXGBE_RXDADV_NEXTP_MASK) >>
>>>>> +                               IXGBE_RXDADV_NEXTP_SHIFT;
>>>>> +            else
>>>>> +                nextp_id = next_id;
>>>>> +
>>>>> +            next_rsc_entry = &sw_rsc_ring[nextp_id];
>>>>> +            next_rxe = &sw_ring[nextp_id];
>>>>> +            rte_ixgbe_prefetch(next_rxe);
>>>>> +        }
>>>>> +
>>>>> +        rsc_entry = &sw_rsc_ring[rx_id];
>>>>> +        first_seg = rsc_entry->fbuf;
>>>>> +        rsc_entry->fbuf = NULL;
>>>>> +
>>>>> +        /*
>>>>> +         * If this is the first buffer of the received packet,
>>>>> +         * set the pointer to the first mbuf of the packet and
>>>>> +         * initialize its context.
>>>>> +         * Otherwise, update the total length and the number of
>>>>> segments
>>>>> +         * of the current scattered packet, and update the pointer to
>>>>> +         * the last mbuf of the current packet.
>>>>> +         */
>>>>> +        if (first_seg == NULL) {
>>>>> +            first_seg = rxm;
>>>>> +            first_seg->pkt_len = data_len;
>>>>> +            first_seg->nb_segs = 1;
>>>>> +        } else {
>>>>> +            first_seg->pkt_len += data_len;
>>>>> +            first_seg->nb_segs++;
>>>>> +        }
>>>>> +
>>>>> +        prev_id = rx_id;
>>>>> +        rx_id = next_id;
>>>>> +
>>>>> +        /*
>>>>> +         * If this is not the last buffer of the received packet,
>>>>> update
>>>>> +         * the pointer to the first mbuf at the NEXTP entry in the
>>>>> +         * sw_rsc_ring and continue to parse the RX ring.
>>>>> +         */
>>>>> +        if (!eop) {
>>>>> +            rxm->next = next_rxe->mbuf;
>>>>> +            next_rsc_entry->fbuf = first_seg;
>>>>> +            goto next_desc;
>>>>> +        }
>>>>> +
>>>>> +        /*
>>>>> +         * This is the last buffer of the received packet - return
>>>>> +         * the current cluster to the user.
>>>>> +         */
>>>>> +        rxm->next = NULL;
>>>>> +
>>>>> +        /* Initialize the first mbuf of the returned packet */
>>>>> +        ixgbe_fill_cluster_head_buf(first_seg, &rxd, rxq->port_id,
>>>>> +                        staterr);
>>>>> +
>>>>> +        /* Prefetch data of first segment, if configured to do so. */
>>>>> +        rte_packet_prefetch((char *)first_seg->buf_addr +
>>>>> +            first_seg->data_off);
>>>>> +
>>>>> +        /*
>>>>> +         * Store the mbuf address into the next entry of the array
>>>>> +         * of returned packets.
>>>>> +         */
>>>>> +        rx_pkts[nb_rx++] = first_seg;
>>>>> +    }
>>>>> +
>>>>> +    /*
>>>>> +     * Record index of the next RX descriptor to probe.
>>>>> +     */
>>>>> +    rxq->rx_tail = rx_id;
>>>>> +
>>>>> +    /*
>>>>> +     * If the number of free RX descriptors is greater than the RX
>>>>> free
>>>>> +     * threshold of the queue, advance the Receive Descriptor Tail
>>>>> (RDT)
>>>>> +     * register.
>>>>> +     * Update the RDT with the value of the last processed RX
>>>>> descriptor
>>>>> +     * minus 1, to guarantee that the RDT register is never equal
>>>>> to the
>>>>> +     * RDH register, which creates a "full" ring situtation from the
>>>>> +     * hardware point of view...
>>>>> +     */
>>>>> +    if (!bulk_alloc && nb_hold > rxq->rx_free_thresh) {
>>>>> +        PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_tail=%u "
>>>>> +               "nb_hold=%u nb_rx=%u",
>>>>> +               rxq->port_id, rxq->queue_id, rx_id, nb_hold, nb_rx);
>>>>> +
>>>>> +        rte_wmb();
>>>>> +        IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr, prev_id);
>>>>> +        nb_hold = 0;
>>>>> +    }
>>>>> +
>>>>> +    rxq->nb_rx_hold = nb_hold;
>>>>> +    return nb_rx;
>>>>> +}
>>>>> +
>>>>> +uint16_t
>>>>> +ixgbe_recv_pkts_lro_single_alloc(void *rx_queue, struct rte_mbuf
>>>>> **rx_pkts,
>>>>> +                 uint16_t nb_pkts)
>>>>> +{
>>>>> +    return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, false);
>>>>> +}
>>>>> +
>>>>> +uint16_t
>>>>> +ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue, struct rte_mbuf
>>>>> **rx_pkts,
>>>>> +                   uint16_t nb_pkts)
>>>>> +{
>>>>> +    return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, true);
>>>>> +}
>>>>> +
>>>>>    uint16_t
>>>>>    ixgbe_recv_scattered_pkts(void *rx_queue, struct rte_mbuf **rx_pkts,
>>>>>                  uint16_t nb_pkts)
>>>>> @@ -2005,6 +2295,31 @@ ixgbe_dev_tx_queue_setup(struct rte_eth_dev
>>>>> *dev,
>>>>>        return (0);
>>>>>    }
>>>>>
>>>>> +/**
>>>>> + * ixgbe_free_rsc_cluster - free the not-yet-completed RSC cluster
>>>>> + *
>>>>> + * The "next" pointer of the last segment of (not-yet-completed)
>>>>> RSC clusters
>>>>> + * in the sw_rsc_ring is not set to NULL but rather points to the next
>>>>> + * mbuf of this RSC aggregation (that has not been completed yet
>>>>> and still
>>>>> + * resides on the HW ring). So, instead of calling for
>>>>> rte_pktmbuf_free() we
>>>>> + * will just free first "nb_segs" segments of the cluster
>>>>> explicitly by calling
>>>>> + * an rte_pktmbuf_free_seg().
>>>>> + *
>>>>> + * @m RSC cluster head
>>>>> + */
>>>>> +static void
>>>>> +ixgbe_free_rsc_cluster(struct rte_mbuf *m)
>>>>> +{
>>>>> +    uint8_t i, nb_segs = m->nb_segs;
>>>>> +    struct rte_mbuf *next_seg;
>>>>> +
>>>>> +    for (i = 0; i < nb_segs; i++) {
>>>>> +        next_seg = m->next;
>>>>> +        rte_pktmbuf_free_seg(m);
>>>>> +        m = next_seg;
>>>>> +    }
>>>>> +}
>>>>> +
>>>>>    static void
>>>>>    ixgbe_rx_queue_release_mbufs(struct ixgbe_rx_queue *rxq)
>>>>>    {
>>>>> @@ -2028,6 +2343,13 @@ ixgbe_rx_queue_release_mbufs(struct
>>>>> ixgbe_rx_queue *rxq)
>>>>>            }
>>>>>    #endif
>>>>>        }
>>>>> +
>>>>> +    if (rxq->sw_rsc_ring)
>>>>> +        for (i = 0; i < rxq->nb_rx_desc; i++)
>>>>> +            if (rxq->sw_rsc_ring[i].fbuf) {
>>>>> + ixgbe_free_rsc_cluster(rxq->sw_rsc_ring[i].fbuf);
>>>>> +                rxq->sw_rsc_ring[i].fbuf = NULL;
>>>>> +            }
>>>>>    }
>>>>>
>>>>>    static void
>>>>> @@ -2036,6 +2358,7 @@ ixgbe_rx_queue_release(struct ixgbe_rx_queue
>>>>> *rxq)
>>>>>        if (rxq != NULL) {
>>>>>            ixgbe_rx_queue_release_mbufs(rxq);
>>>>>            rte_free(rxq->sw_ring);
>>>>> +        rte_free(rxq->sw_rsc_ring);
>>>>>            rte_free(rxq);
>>>>>        }
>>>>>    }
>>>>> @@ -2158,6 +2481,7 @@ ixgbe_reset_rx_queue(struct ixgbe_hw *hw,
>>>>> struct ixgbe_rx_queue *rxq)
>>>>>        rxq->nb_rx_hold = 0;
>>>>>        rxq->pkt_first_seg = NULL;
>>>>>        rxq->pkt_last_seg = NULL;
>>>>> +    rxq->rsc_en = 0;
>>>>>    }
>>>>>
>>>>>    int
>>>>> @@ -2172,6 +2496,14 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev
>>>>> *dev,
>>>>>        struct ixgbe_rx_queue *rxq;
>>>>>        struct ixgbe_hw     *hw;
>>>>>        uint16_t len;
>>>>> +    struct rte_eth_dev_info dev_info = { 0 };
>>>>> +    struct rte_eth_rxmode *dev_rx_mode = &dev->data->dev_conf.rxmode;
>>>>> +    bool rsc_requested = false;
>>>>> +
>>>>> +    dev->dev_ops->dev_infos_get(dev, &dev_info);
>>>>> +    if ((dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO) &&
>>>>> +        dev_rx_mode->enable_lro)
>>>>> +        rsc_requested = true;
>>>>>
>>>>>        PMD_INIT_FUNC_TRACE();
>>>>>        hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>>>>> @@ -2277,12 +2609,27 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev
>>>>> *dev,
>>>>>        rxq->sw_ring = rte_zmalloc_socket("rxq->sw_ring",
>>>>>                          sizeof(struct ixgbe_rx_entry) * len,
>>>>>                          RTE_CACHE_LINE_SIZE, socket_id);
>>>>> -    if (rxq->sw_ring == NULL) {
>>>>> +    if (!rxq->sw_ring) {
>>>>>            ixgbe_rx_queue_release(rxq);
>>>>>            return (-ENOMEM);
>>>>>        }
>>>>> -    PMD_INIT_LOG(DEBUG, "sw_ring=%p hw_ring=%p dma_addr=0x%"PRIx64,
>>>>> -             rxq->sw_ring, rxq->rx_ring, rxq->rx_ring_phys_addr);
>>>>> +
>>>>> +    if (rsc_requested) {
>>>>> +        rxq->sw_rsc_ring =
>>>>> +            rte_zmalloc_socket("rxq->sw_rsc_ring",
>>>>> +                       sizeof(struct ixgbe_rsc_entry) * len,
>>>>> +                       RTE_CACHE_LINE_SIZE, socket_id);
>>>>> +        if (!rxq->sw_rsc_ring) {
>>>>> +            ixgbe_rx_queue_release(rxq);
>>>>> +            return (-ENOMEM);
>>>>> +        }
>>>>> +    } else
>>>>> +        rxq->sw_rsc_ring = NULL;
>>>>> +
>>>>> +    PMD_INIT_LOG(DEBUG, "sw_ring=%p sw_rsc_ring=%p hw_ring=%p "
>>>>> +                "dma_addr=0x%"PRIx64,
>>>>> +             rxq->sw_ring, rxq->sw_rsc_ring, rxq->rx_ring,
>>>>> +             rxq->rx_ring_phys_addr);
>>>>>
>>>>>        if (!rte_is_power_of_2(nb_desc)) {
>>>>>            PMD_INIT_LOG(DEBUG, "queue[%d] doesn't meet Vector Rx "
>>>>> @@ -3527,6 +3874,91 @@ ixgbe_dev_mq_tx_configure(struct rte_eth_dev
>>>>> *dev)
>>>>>        return 0;
>>>>>    }
>>>>>
>>>>> +/**
>>>>> + * ixgbe_get_rscctl_maxdesc - Calculate the RSCCTL[n].MAXDESC for PF
>>>>> + *
>>>>> + * Return the RSCCTL[n].MAXDESC for 82599 and x540 PF devices
>>>>> according to the
>>>>> + * spec rev. 3.0 chapter 8.2.3.8.13.
>>>>> + *
>>>>> + * @pool Memory pool of the Rx queue
>>>>> + */
>>>>> +static inline uint32_t
>>>>> +ixgbe_get_rscctl_maxdesc(struct rte_mempool *pool)
>>>>> +{
>>>>> +    struct rte_pktmbuf_pool_private *mp_priv =
>>>>> rte_mempool_get_priv(pool);
>>>>> +
>>>>> +    /* MAXDESC * SRRCTL.BSIZEPKT must not exceed 64 KB minus one */
>>>>> +    uint16_t maxdesc =
>>>>> +        IPV4_MAX_PKT_LEN /
>>>>> +            (mp_priv->mbuf_data_room_size - RTE_PKTMBUF_HEADROOM);
>>>>> +
>>>>> +    if (maxdesc >= 16)
>>>>> +        return IXGBE_RSCCTL_MAXDESC_16;
>>>>> +    else if (maxdesc >= 8)
>>>>> +        return IXGBE_RSCCTL_MAXDESC_8;
>>>>> +    else if (maxdesc >= 4)
>>>>> +        return IXGBE_RSCCTL_MAXDESC_4;
>>>>> +    else
>>>>> +        return IXGBE_RSCCTL_MAXDESC_1;
>>>>> +}
>>>>> +
>>>>> +/**
>>>>> + * ixgbe_set_ivar - Setup the correct IVAR register for a
>>>>> particular MSIX
>>>>> + * interrupt
>>>>> + *
>>>>> + * (Taken from FreeBSD tree)
>>>>> + * (yes this is all very magic and confusing :)
>>>>> + *
>>>>> + * @dev port handle
>>>>> + * @entry the register array entry
>>>>> + * @vector the MSIX vector for this queue
>>>>> + * @type RX/TX/MISC
>>>>> + */
>>>>> +static void
>>>>> +ixgbe_set_ivar(struct rte_eth_dev *dev, u8 entry, u8 vector, s8 type)
>>>>> +{
>>>>> +    struct ixgbe_hw *hw =
>>>>> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>>>>> +    u32 ivar, index;
>>>>> +
>>>>> +    vector |= IXGBE_IVAR_ALLOC_VAL;
>>>>> +
>>>>> +    switch (hw->mac.type) {
>>>>> +
>>>>> +    case ixgbe_mac_82598EB:
>>>>> +        if (type == -1)
>>>>> +            entry = IXGBE_IVAR_OTHER_CAUSES_INDEX;
>>>>> +        else
>>>>> +            entry += (type * 64);
>>>>> +        index = (entry >> 2) & 0x1F;
>>>>> +        ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(index));
>>>>> +        ivar &= ~(0xFF << (8 * (entry & 0x3)));
>>>>> +        ivar |= (vector << (8 * (entry & 0x3)));
>>>>> +        IXGBE_WRITE_REG(hw, IXGBE_IVAR(index), ivar);
>>>>> +        break;
>>>>> +
>>>>> +    case ixgbe_mac_82599EB:
>>>>> +    case ixgbe_mac_X540:
>>>>> +        if (type == -1) { /* MISC IVAR */
>>>>> +            index = (entry & 1) * 8;
>>>>> +            ivar = IXGBE_READ_REG(hw, IXGBE_IVAR_MISC);
>>>>> +            ivar &= ~(0xFF << index);
>>>>> +            ivar |= (vector << index);
>>>>> +            IXGBE_WRITE_REG(hw, IXGBE_IVAR_MISC, ivar);
>>>>> +        } else {    /* RX/TX IVARS */
>>>>> +            index = (16 * (entry & 1)) + (8 * type);
>>>>> +            ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(entry >> 1));
>>>>> +            ivar &= ~(0xFF << index);
>>>>> +            ivar |= (vector << index);
>>>>> +            IXGBE_WRITE_REG(hw, IXGBE_IVAR(entry >> 1), ivar);
>>>>> +        }
>>>>> +
>>>>> +        break;
>>>>> +
>>>>> +    default:
>>>>> +        break;
>>>>> +    }
>>>>> +}
>>>>> +
>>>>>    void ixgbe_set_rx_function(struct rte_eth_dev *dev)
>>>>>    {
>>>>>        struct ixgbe_hw *hw =
>>>>> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>>>>> @@ -3545,7 +3977,24 @@ void ixgbe_set_rx_function(struct rte_eth_dev
>>>>> *dev)
>>>>>            hw->rx_vec_allowed = false;
>>>>>        }
>>>>>
>>>>> -    if (dev->data->scattered_rx) {
>>>>> +    /*
>>>>> +     * Initialize the appropriate LRO callback.
>>>>> +     *
>>>>> +     * If all queues satisfy the bulk allocation preconditions
>>>>> +     * (hw->rx_bulk_alloc_allowed is TRUE) then we may use bulk
>>>>> allocation.
>>>>> +     * Otherwise use a single allocation version.
>>>>> +     */
>>>>> +    if (dev->data->lro) {
>>>>> +        if (hw->rx_bulk_alloc_allowed) {
>>>>> +            PMD_INIT_LOG(INFO, "LRO is requested. Using a bulk "
>>>>> +                       "allocation version");
>>>>> +            dev->rx_pkt_burst = ixgbe_recv_pkts_lro_bulk_alloc;
>>>>> +        } else {
>>>>> +            PMD_INIT_LOG(INFO, "LRO is requested. Using a single "
>>>>> +                       "allocation version");
>>>>> +            dev->rx_pkt_burst = ixgbe_recv_pkts_lro_single_alloc;
>>>>> +        }
>>>>> +    } else if (dev->data->scattered_rx) {
>>>>>            /*
>>>>>             * Set the non-LRO scattered callback: there are Vector and
>>>>>             * single allocation versions.
>>>>> @@ -3595,6 +4044,149 @@ void ixgbe_set_rx_function(struct
>>>>> rte_eth_dev *dev)
>>>>>        }
>>>>>    }
>>>>>
>>>>> +/**
>>>>> + * ixgbe_set_rsc - configure RSC related port HW registers
>>>>> + *
>>>>> + * Configures the port's RSC related registers according to the
>>>>> 4.6.7.2 chapter
>>>>> + * of 82599 Spec (x540 configuration is virtually the same).
>>>>> + *
>>>>> + * @dev port handle
>>>>> + *
>>>>> + * Returns 0 in case of success or a non-zero error code
>>>>> + */
>>>>> +static int
>>>>> +ixgbe_set_rsc(struct rte_eth_dev *dev)
>>>>> +{
>>>>> +    struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
>>>>> +    struct ixgbe_hw *hw =
>>>>> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>>>>> +    struct rte_eth_dev_info dev_info = { 0 };
>>>>> +    bool rsc_capable = false;
>>>>> +    uint16_t i;
>>>>> +    uint32_t rdrxctl;
>>>>> +
>>>>> +    /* Sanity check */
>>>>> +    dev->dev_ops->dev_infos_get(dev, &dev_info);
>>>>> +    if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO)
>>>>> +        rsc_capable = true;
>>>>> +
>>>>> +    if (!rsc_capable && rx_conf->enable_lro) {
>>>>> +        PMD_INIT_LOG(CRIT, "LRO is requested on HW that doesn't "
>>>>> +                   "support it");
>>>>> +        return -EINVAL;
>>>>> +    }
>>>>> +
>>>>> +    /* RSC global configuration (chapter 4.6.7.2.1 of 82599 Spec) */
>>>>> +
>>>>> +    if (!rx_conf->hw_strip_crc && rx_conf->enable_lro) {
>>>>> +        /*
>>>>> +         * According to chapter of 4.6.7.2.1 of the Spec Rev.
>>>>> +         * 3.0 RSC configuration requires HW CRC stripping being
>>>>> +         * enabled. If user requested both HW CRC stripping off
>>>>> +         * and RSC on - return an error.
>>>>> +         */
>>>>> +        PMD_INIT_LOG(CRIT, "LRO can't be enabled when HW CRC "
>>>>> +                    "is disabled");
>>>>> +        return -EINVAL;
>>>>> +    }
>>>>> +
>>>>> +    /* RFCTL configuration  */
>>>>> +    if (rsc_capable) {
>>>>> +        uint32_t rfctl = IXGBE_READ_REG(hw, IXGBE_RFCTL);
>>>>> +        if (rx_conf->enable_lro)
>>>>> +            /*
>>>>> +             * Since NFS packets coalescing is not supported - clear
>>>>> +             * RFCTL.NFSW_DIS and RFCTL.NFSR_DIS when RSC is
>>>>> +             * enabled.
>>>>> +             */
>>>>> +            rfctl &= ~(IXGBE_RFCTL_RSC_DIS | IXGBE_RFCTL_NFSW_DIS |
>>>>> +                   IXGBE_RFCTL_NFSR_DIS);
>>>>> +        else
>>>>> +            rfctl |= IXGBE_RFCTL_RSC_DIS;
>>>>> +
>>>>> +        IXGBE_WRITE_REG(hw, IXGBE_RFCTL, rfctl);
>>>>> +    }
>>>>> +
>>>>> +    /* If LRO hasn't been requested - we are done here. */
>>>>> +    if (!rx_conf->enable_lro)
>>>>> +        return 0;
>>>>> +
>>>>> +    /* Set RDRXCTL.RSCACKC bit */
>>>>> +    rdrxctl = IXGBE_READ_REG(hw, IXGBE_RDRXCTL);
>>>>> +    rdrxctl |= IXGBE_RDRXCTL_RSCACKC;
>>>>> +    IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
>>>>> +
>>>>> +    /* Per-queue RSC configuration (chapter 4.6.7.2.2 of 82599
>>>>> Spec) */
>>>>> +    for (i = 0; i < dev->data->nb_rx_queues; i++) {
>>>>> +        struct ixgbe_rx_queue *rxq = dev->data->rx_queues[i];
>>>>> +        uint32_t srrctl =
>>>>> +            IXGBE_READ_REG(hw, IXGBE_SRRCTL(rxq->reg_idx));
>>>>> +        uint32_t rscctl =
>>>>> +            IXGBE_READ_REG(hw, IXGBE_RSCCTL(rxq->reg_idx));
>>>>> +        uint32_t psrtype =
>>>>> +            IXGBE_READ_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx));
>>>>> +        uint32_t eitr =
>>>>> +            IXGBE_READ_REG(hw, IXGBE_EITR(rxq->reg_idx));
>>>>> +
>>>>> +        /*
>>>>> +         * ixgbe PMD doesn't support header-split at the moment.
>>>>> +         *
>>>>> +         * Following the 4.6.7.2.1 chapter of the 82599/x540
>>>>> +         * Spec if RSC is enabled the SRRCTL[n].BSIZEHEADER
>>>>> +         * should be configured even if header split is not
>>>>> +         * enabled. We will configure it 128 bytes following the
>>>>> +         * recommendation in the spec.
>>>>> +         */
>>>>> +        srrctl &= ~IXGBE_SRRCTL_BSIZEHDR_MASK;
>>>>> +        srrctl |= (128 << IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT) &
>>>>> +                        IXGBE_SRRCTL_BSIZEHDR_MASK;
>>>>> +
>>>>> +        /*
>>>>> +         * TODO: Consider setting the Receive Descriptor Minimum
>>>>> +         * Threshold Size for an RSC case. This is not an obviously
>>>>> +         * beneficiary option but the one worth considering...
>>>>> +         */
>>>>> +
>>>>> +        rscctl |= IXGBE_RSCCTL_RSCEN;
>>>>> +        rscctl |= ixgbe_get_rscctl_maxdesc(rxq->mb_pool);
>>>>> +        psrtype |= IXGBE_PSRTYPE_TCPHDR;
>>>>> +
>>>>> +        /*
>>>>> +         * RSC: Set ITR interval corresponding to 2K ints/s.
>>>>> +         *
>>>>> +         * Full-sized RSC aggregations for a 10Gb/s link will
>>>>> +         * arrive at about 20K aggregation/s rate.
>>>>> +         *
>>>>> +         * 2K inst/s rate will make only 10% of the
>>>>> +         * aggregations to be closed due to the interrupt timer
>>>>> +         * expiration for a streaming at wire-speed case.
>>>>> +         *
>>>>> +         * For a sparse streaming case this setting will yield
>>>>> +         * at most 500us latency for a single RSC aggregation.
>>>>> +         */
>>>>> +        eitr &= ~IXGBE_EITR_ITR_INT_MASK;
>>>>> +        eitr |= IXGBE_EITR_INTERVAL_US(500) | IXGBE_EITR_CNT_WDIS;
>>>>> +
>>>>> +        IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
>>>>> +        IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(rxq->reg_idx), rscctl);
>>>>> +        IXGBE_WRITE_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx), psrtype);
>>>>> +        IXGBE_WRITE_REG(hw, IXGBE_EITR(rxq->reg_idx), eitr);
>>>>> +
>>>>> +        /*
>>>>> +         * RSC requires the mapping of the queue to the
>>>>> +         * interrupt vector.
>>>>> +         */
>>>>> +        ixgbe_set_ivar(dev, rxq->reg_idx, i, 0);
>>>>> +
>>>>> +        rxq->rsc_en = 1;
>>>>> +    }
>>>>> +
>>>>> +    dev->data->lro = 1;
>>>>> +
>>>>> +    PMD_INIT_LOG(INFO, "enabling LRO mode");
>>>>> +
>>>>> +    return 0;
>>>>> +}
>>>>> +
>>>>>    /*
>>>>>     * Initializes Receive Unit.
>>>>>     */
>>>>> @@ -3615,6 +4207,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>>>>        uint16_t buf_size;
>>>>>        uint16_t i;
>>>>>        struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
>>>>> +    int rc;
>>>>>
>>>>>        PMD_INIT_FUNC_TRACE();
>>>>>        hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>>>>> @@ -3724,6 +4317,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>>>>                           RTE_PKTMBUF_HEADROOM);
>>>>>            srrctl |= ((buf_size >> IXGBE_SRRCTL_BSIZEPKT_SHIFT) &
>>>>>                   IXGBE_SRRCTL_BSIZEPKT_MASK);
>>>>> +
>>>>>            IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
>>>>>
>>>>>            buf_size = (uint16_t) ((srrctl &
>>>>> IXGBE_SRRCTL_BSIZEPKT_MASK) <<
>>>>> @@ -3738,8 +4332,6 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>>>>        if (rx_conf->enable_scatter)
>>>>>            dev->data->scattered_rx = 1;
>>>>>
>>>>> -    ixgbe_set_rx_function(dev);
>>>>> -
>>>>>        /*
>>>>>         * Device configured with multiple RX queues.
>>>>>         */
>>>>> @@ -3770,6 +4362,12 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>>>>            IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
>>>>>        }
>>>>>
>>>>> +    rc = ixgbe_set_rsc(dev);
>>>>> +    if (rc)
>>>>> +        return rc;
>>>>> +
>>>>> +    ixgbe_set_rx_function(dev);
>>>>> +
>>>>>        return 0;
>>>>>    }
>>>>>
>>>>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
>>>>> b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
>>>>> index 3937cf6..120bbbd 100644
>>>>> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
>>>>> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
>>>>> @@ -79,6 +79,10 @@ struct ixgbe_rx_entry {
>>>>>        struct rte_mbuf *mbuf; /**< mbuf associated with RX
>>>>> descriptor. */
>>>>>    };
>>>>>
>>>>> +struct ixgbe_rsc_entry {
>>>>> +    struct rte_mbuf *fbuf; /**< First segment of the fragmented
>>>>> packet. */
>>>>> +};
>>>>> +
>>>>>    /**
>>>>>     * Structure associated with each descriptor of the TX ring of a
>>>>> TX queue.
>>>>>     */
>>>>> @@ -105,6 +109,7 @@ struct ixgbe_rx_queue {
>>>>>        volatile uint32_t   *rdt_reg_addr; /**< RDT register address. */
>>>>>        volatile uint32_t   *rdh_reg_addr; /**< RDH register address. */
>>>>>        struct ixgbe_rx_entry *sw_ring; /**< address of RX software
>>>>> ring. */
>>>>> +    struct ixgbe_rsc_entry *sw_rsc_ring; /**< address of RSC
>>>>> software ring. */
>>>>>        struct rte_mbuf *pkt_first_seg; /**< First segment of current
>>>>> packet. */
>>>>>        struct rte_mbuf *pkt_last_seg; /**< Last segment of current
>>>>> packet. */
>>>>>        uint64_t            mbuf_initializer; /**< value to init mbufs */
>>>>> @@ -126,6 +131,7 @@ struct ixgbe_rx_queue {
>>>>>        uint8_t             port_id;  /**< Device port identifier. */
>>>>>        uint8_t             crc_len;  /**< 0 if CRC stripped, 4
>>>>> otherwise. */
>>>>>        uint8_t             drop_en;  /**< If not 0, set
>>>>> SRRCTL.Drop_En. */
>>>>> +    uint8_t             rsc_en;   /**< If not 0, RSC is enabled. */
>>>>>        uint8_t             rx_deferred_start; /**< not in global dev
>>>>> start. */
>>>>>    #ifdef RTE_LIBRTE_IXGBE_RX_ALLOW_BULK_ALLOC
>>>>>        /** need to alloc dummy mbuf, for wraparound when scanning hw
>>>>> ring */
>>>>> --
>>>>> 2.1.0

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
  2015-03-30 15:37     ` Vlad Zolotarov
@ 2015-03-30 15:57       ` Vlad Zolotarov
  0 siblings, 0 replies; 6+ messages in thread
From: Vlad Zolotarov @ 2015-03-30 15:57 UTC (permalink / raw)
  To: Ananyev, Konstantin, dev



On 03/30/15 18:37, Vlad Zolotarov wrote:
>
>
> On 03/30/15 17:18, Ananyev, Konstantin wrote:
>> Hi Vlad,
>>
>>> -----Original Message-----
>>> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Vlad Zolotarov
>>> Sent: Wednesday, March 18, 2015 5:52 PM
>>> To: dev@dpdk.org
>>> Subject: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
>>>
>>>      - Only x540 and 82599 devices support LRO.
>>>      - Add the appropriate HW configuration.
>>>      - Add RSC aware rx_pkt_burst() handlers:
>>>         - Implemented bulk allocation and non-bulk allocation versions.
>>>         - Add LRO-specific fields to rte_eth_rxmode, to 
>>> rte_eth_dev_data
>>>           and to ixgbe_rx_queue.
>>>         - Use the appropriate handler when LRO is requested.
>>>
>>> Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
>>> ---
>>> New in v8:
>>>     - Took the RSC configuration code from ixgbe_dev_rx_init() into 
>>> a separate
>>>       function - ixgbe_set_rsc().
>>>     - Added some missing macros for HW configuration.
>>>     - Styling adjustments:
>>>        - Functions names.
>>>        - Functions descriptions.
>>>     - Reworked the ixgbe_free_rsc_cluster() code to make it more 
>>> readable.
>>>     - Kill the HEADER_SPLIT flow in ixgbe_set_rsc() since it's not 
>>> supported by
>>>       ixgbe PMD.
>>>
>>> New in v7:
>>>     - Free not-yet-completed RSC aggregations in rte_eth_dev_stop() 
>>> flow.
>>>     - Reset the sw_ring[].mbuf entry in a bulk allocation case.
>>>       This is needed for ixgbe_rx_queue_release_mbufs().
>>>     - _recv_pkts_lro(): added the missing memory barrier before RDT 
>>> update in a
>>>       non-bulk allocation case.
>>>     - Don't allow RSC when device is configured in an SR-IOV mode.
>>>
>>> New in v5:
>>>     - Put the RTE_ETHDEV_HAS_LRO_SUPPORT definition at the beginning 
>>> of rte_ethdev.h.
>>>     - Removed the "TODO: Remove me" comment near 
>>> RTE_ETHDEV_HAS_LRO_SUPPORT.
>>>
>>> New in v4:
>>>     - Define RTE_ETHDEV_HAS_LRO_SUPPORT in rte_ethdev.h instead of
>>>       RTE_ETHDEV_LRO_SUPPORT defined in config/common_linuxapp.
>>>
>>> New in v2:
>>>     - Removed rte_eth_dev_data.lro_bulk_alloc.
>>>     - Fixed a few styling and spelling issues.
>>> ---
>>>   lib/librte_ether/rte_ethdev.h           |   9 +-
>>>   lib/librte_net/rte_ip.h                 |   3 +
>>>   lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h |   6 +
>>>   lib/librte_pmd_ixgbe/ixgbe_ethdev.c     |  11 +
>>>   lib/librte_pmd_ixgbe/ixgbe_ethdev.h     |   5 +
>>>   lib/librte_pmd_ixgbe/ixgbe_rxtx.c       | 610 
>>> +++++++++++++++++++++++++++++++-
>>>   lib/librte_pmd_ixgbe/ixgbe_rxtx.h       |   6 +
>>>   7 files changed, 642 insertions(+), 8 deletions(-)
>>>
>>> diff --git a/lib/librte_ether/rte_ethdev.h 
>>> b/lib/librte_ether/rte_ethdev.h
>>> index 21aa359..61dc49a 100644
>>> --- a/lib/librte_ether/rte_ethdev.h
>>> +++ b/lib/librte_ether/rte_ethdev.h
>>> @@ -172,6 +172,9 @@ extern "C" {
>>>
>>>   #include <stdint.h>
>>>
>>> +/* Use this macro to check if LRO API is supported */
>>> +#define RTE_ETHDEV_HAS_LRO_SUPPORT
>>> +
>>>   #include <rte_log.h>
>>>   #include <rte_interrupts.h>
>>>   #include <rte_pci.h>
>>> @@ -320,14 +323,15 @@ struct rte_eth_rxmode {
>>>       enum rte_eth_rx_mq_mode mq_mode;
>>>       uint32_t max_rx_pkt_len;  /**< Only used if jumbo_frame 
>>> enabled. */
>>>       uint16_t split_hdr_size;  /**< hdr buf size (header_split 
>>> enabled).*/
>>> -    uint8_t header_split : 1, /**< Header Split enable. */
>>> +    uint16_t header_split : 1, /**< Header Split enable. */
>>>           hw_ip_checksum   : 1, /**< IP/UDP/TCP checksum offload 
>>> enable. */
>>>           hw_vlan_filter   : 1, /**< VLAN filter enable. */
>>>           hw_vlan_strip    : 1, /**< VLAN strip enable. */
>>>           hw_vlan_extend   : 1, /**< Extended VLAN enable. */
>>>           jumbo_frame      : 1, /**< Jumbo Frame Receipt enable. */
>>>           hw_strip_crc     : 1, /**< Enable CRC stripping by 
>>> hardware. */
>>> -        enable_scatter   : 1; /**< Enable scatter packets rx 
>>> handler */
>>> +        enable_scatter   : 1, /**< Enable scatter packets rx 
>>> handler */
>>> +        enable_lro       : 1; /**< Enable LRO */
>>>   };
>>>
>>>   /**
>>> @@ -1515,6 +1519,7 @@ struct rte_eth_dev_data {
>>>       uint8_t port_id;           /**< Device [external] port 
>>> identifier. */
>>>       uint8_t promiscuous   : 1, /**< RX promiscuous mode ON(1) / 
>>> OFF(0). */
>>>           scattered_rx : 1,  /**< RX of scattered packets is ON(1) / 
>>> OFF(0) */
>>> +        lro          : 1,  /**< RX LRO is ON(1) / OFF(0) */
>>>           all_multicast : 1, /**< RX all multicast mode ON(1) / 
>>> OFF(0). */
>>>           dev_started : 1;   /**< Device state: STARTED(1) / 
>>> STOPPED(0). */
>>>   };
>>> diff --git a/lib/librte_net/rte_ip.h b/lib/librte_net/rte_ip.h
>>> index 64935d9..74c9ced 100644
>>> --- a/lib/librte_net/rte_ip.h
>>> +++ b/lib/librte_net/rte_ip.h
>>> @@ -110,6 +110,9 @@ struct ipv4_hdr {
>>>                          (((c) & 0xff) << 8)  | \
>>>                          ((d) & 0xff))
>>>
>>> +/** Maximal IPv4 packet length (including a header) */
>>> +#define IPV4_MAX_PKT_LEN        65535
>>> +
>>>   /** Internet header length mask for version_ihl field */
>>>   #define IPV4_HDR_IHL_MASK    (0x0f)
>>>   /**
>>> diff --git a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h 
>>> b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
>>> index 9a66370..4998627 100644
>>> --- a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
>>> +++ b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
>>> @@ -234,8 +234,14 @@ struct ixgbe_thermal_sensor_data {
>>>   #define IXGBE_EITR(_i)        (((_i) <= 23) ? (0x00820 + ((_i) * 
>>> 4)) : \
>>>                    (0x012300 + (((_i) - 24) * 4)))
>>>   #define IXGBE_EITR_ITR_INT_MASK    0x00000FF8
>>> +#define IXGBE_EITR_ITR_INT_SHIFT 3
>>>   #define IXGBE_EITR_LLI_MOD    0x00008000
>>>   #define IXGBE_EITR_CNT_WDIS    0x80000000
>>> +/* EITR Inteval is in 2048ns uinits for 1G and 10G link */
>>> +#define IXGBE_EITR_INTERVAL_UNIT_NS    2048
>> Why is that? Why not just 2us as 82599 spec says?
>> And then:
>> +#define IXGBE_EITR_INTERVAL_US(us) (((us) / 
>> IXGBE_EITR_INTERVAL_UNIT_US << IXGBE_EITR_ITR_INT_SHIFT) & 
>> IXGBE_EITR_ITR_INT_MASK)
>> ?
>
> Because spec doesn't say 2us but rather 2.048us - see 8.2.4.5.16 
> chapter of x540 spec.

The most confusing part is that 82599 Rev. 3.0 spec does say so. The 
x540 spec I have is dated by March 2014 and 82599 spec is dated by 
November 2014 but according to changelog EITR description has never been 
updated. Therefore I conclude that the more recent device spec (x540) 
holds the most up to date content.

Pls., confirm.

thanks,
vlad

>
>>
>>> +#define IXGBE_EITR_INTERVAL_US(us)    \
>>> +   (((us) * 1000 / IXGBE_EITR_INTERVAL_UNIT_NS << 
>>> IXGBE_EITR_ITR_INT_SHIFT) & \
>>> +        IXGBE_EITR_ITR_INT_MASK)
>>
>> Unfortunately we are not supposed to change files under ixgbe 
>> subfirectory (except ixgbe_osdep.*).
>> These files comes from ixgbe shared code and we treat them as read-only.
>> You need to move these new macros you added into ixgbe_ethedev.h.
>
> Aha... Ok. No problem.
>
>>
>> All other things look good to me.
>> Konstantin
>>
>>>   #define IXGBE_IVAR(_i)        (0x00900 + ((_i) * 4)) /* 24 at 
>>> 0x900-0x960 */
>>>   #define IXGBE_IVAR_MISC        0x00A00 /* misc MSI-X interrupt 
>>> causes */
>>>   #define IXGBE_EITRSEL        0x00894
>>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c 
>>> b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>>> index 92d75db..923692e 100644
>>> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>>> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>>> @@ -1645,6 +1645,7 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
>>>
>>>       /* Clear stored conf */
>>>       dev->data->scattered_rx = 0;
>>> +    dev->data->lro = 0;
>>>
>>>       /* Clear recorded link status */
>>>       memset(&link, 0, sizeof(link));
>>> @@ -2013,6 +2014,16 @@ ixgbe_dev_info_get(struct rte_eth_dev *dev, 
>>> struct rte_eth_dev_info *dev_info)
>>>           DEV_RX_OFFLOAD_IPV4_CKSUM |
>>>           DEV_RX_OFFLOAD_UDP_CKSUM  |
>>>           DEV_RX_OFFLOAD_TCP_CKSUM;
>>> +
>>> +    /*
>>> +     * RSC is only supported by 82599 and x540 PF devices in a 
>>> non-SR-IOV
>>> +     * mode.
>>> +     */
>>> +    if ((hw->mac.type == ixgbe_mac_82599EB ||
>>> +         hw->mac.type == ixgbe_mac_X540) &&
>>> +        !RTE_ETH_DEV_SRIOV(dev).active)
>>> +        dev_info->rx_offload_capa |= DEV_RX_OFFLOAD_TCP_LRO;
>>> +
>>>       dev_info->tx_offload_capa =
>>>           DEV_TX_OFFLOAD_VLAN_INSERT |
>>>           DEV_TX_OFFLOAD_IPV4_CKSUM  |
>>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h 
>>> b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>>> index ffe3471..7050340 100644
>>> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>>> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>>> @@ -344,6 +344,11 @@ uint16_t ixgbe_recv_pkts(void *rx_queue, struct 
>>> rte_mbuf **rx_pkts,
>>>   uint16_t ixgbe_recv_scattered_pkts(void *rx_queue,
>>>           struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
>>>
>>> +uint16_t ixgbe_recv_pkts_lro_single_alloc(void *rx_queue,
>>> +        struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
>>> +uint16_t ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue,
>>> +        struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
>>> +
>>>   uint16_t ixgbe_xmit_pkts(void *tx_queue, struct rte_mbuf **tx_pkts,
>>>           uint16_t nb_pkts);
>>>
>>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c 
>>> b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
>>> index a08ae6a..daa4c45 100644
>>> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
>>> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
>>> @@ -70,6 +70,7 @@
>>>   #include <rte_sctp.h>
>>>   #include <rte_string_fns.h>
>>>   #include <rte_errno.h>
>>> +#include <rte_ip.h>
>>>
>>>   #include "ixgbe_logs.h"
>>>   #include "ixgbe/ixgbe_api.h"
>>> @@ -1422,6 +1423,295 @@ ixgbe_fill_cluster_head_buf(
>>>       }
>>>   }
>>>
>>> +/**
>>> + * ixgbe_recv_pkts_lro - receive handler for and LRO case.
>>> + *
>>> + * @rx_queue Rx queue handle
>>> + * @rx_pkts table of received packets
>>> + * @nb_pkts size of rx_pkts table
>>> + * @bulk_alloc if TRUE bulk allocation is used for a HW ring refilling
>>> + *
>>> + * Handles the Rx HW ring completions when RSC feature is 
>>> configured. Uses an
>>> + * additional ring of ixgbe_rsc_entry's that will hold the relevant 
>>> RSC info.
>>> + *
>>> + * We use the same logic as in Lunux and in FreeBSD ixgbe drivers:
>>> + * 1) When non-EOP RSC completion arrives:
>>> + *    a) Update the HEAD of the current RSC aggregation cluster 
>>> with the new
>>> + *       segment's data length.
>>> + *    b) Set the "next" pointer of the current segment to point to 
>>> the segment
>>> + *       at the NEXTP index.
>>> + *    c) Pass the HEAD of RSC aggregation cluster on to the next 
>>> NEXTP entry
>>> + *       in the sw_rsc_ring.
>>> + * 2) When EOP arrives we just update the cluster's total length 
>>> and offload
>>> + *    flags and deliver the cluster up to the upper layers. In our 
>>> case - put it
>>> + *    in the rx_pkts table.
>>> + *
>>> + * Returns the number of received packets/clusters (according to 
>>> the "bulk
>>> + * receive" interface).
>>> + */
>>> +static inline uint16_t
>>> +ixgbe_recv_pkts_lro(void *rx_queue, struct rte_mbuf **rx_pkts, 
>>> uint16_t nb_pkts,
>>> +            bool bulk_alloc)
>>> +{
>>> +    struct ixgbe_rx_queue *rxq = rx_queue;
>>> +    volatile union ixgbe_adv_rx_desc *rx_ring = rxq->rx_ring;
>>> +    struct ixgbe_rx_entry *sw_ring = rxq->sw_ring;
>>> +    struct ixgbe_rsc_entry *sw_rsc_ring = rxq->sw_rsc_ring;
>>> +    uint16_t rx_id = rxq->rx_tail;
>>> +    uint16_t nb_rx = 0;
>>> +    uint16_t nb_hold = rxq->nb_rx_hold;
>>> +    uint16_t prev_id = rxq->rx_tail;
>>> +
>>> +    while (nb_rx < nb_pkts) {
>>> +        bool eop;
>>> +        struct ixgbe_rx_entry *rxe;
>>> +        struct ixgbe_rsc_entry *rsc_entry;
>>> +        struct ixgbe_rsc_entry *next_rsc_entry;
>>> +        struct ixgbe_rx_entry *next_rxe;
>>> +        struct rte_mbuf *first_seg;
>>> +        struct rte_mbuf *rxm;
>>> +        struct rte_mbuf *nmb;
>>> +        union ixgbe_adv_rx_desc rxd;
>>> +        uint16_t data_len;
>>> +        uint16_t next_id;
>>> +        volatile union ixgbe_adv_rx_desc *rxdp;
>>> +        uint32_t staterr;
>>> +
>>> +next_desc:
>>> +        /*
>>> +         * The code in this whole file uses the volatile pointer to
>>> +         * ensure the read ordering of the status and the rest of the
>>> +         * descriptor fields (on the compiler level only!!!). This 
>>> is so
>>> +         * UGLY - why not to just use the compiler barrier instead? 
>>> DPDK
>>> +         * even has the rte_compiler_barrier() for that.
>>> +         *
>>> +         * But most importantly this is just wrong because this 
>>> doesn't
>>> +         * ensure memory ordering in a general case at all. For
>>> +         * instance, DPDK is supposed to work on Power CPUs where
>>> +         * compiler barrier may just not be enough!
>>> +         *
>>> +         * I tried to write only this function properly to have a
>>> +         * starting point (as a part of an LRO/RSC series) but the
>>> +         * compiler cursed at me when I tried to cast away the
>>> +         * "volatile" from rx_ring (yes, it's volatile too!!!). So, 
>>> I'm
>>> +         * keeping it the way it is for now.
>>> +         *
>>> +         * The code in this file is broken in so many other places and
>>> +         * will just not work on a big endian CPU anyway therefore the
>>> +         * lines below will have to be revisited together with the 
>>> rest
>>> +         * of the ixgbe PMD.
>>> +         *
>>> +         * TODO:
>>> +         *    - Get rid of "volatile" crap and let the compiler do its
>>> +         *      job.
>>> +         *    - Use the proper memory barrier (rte_rmb()) to ensure 
>>> the
>>> +         *      memory ordering below.
>>> +         */
>>> +        rxdp = &rx_ring[rx_id];
>>> +        staterr = rte_le_to_cpu_32(rxdp->wb.upper.status_error);
>>> +
>>> +        if (!(staterr & IXGBE_RXDADV_STAT_DD))
>>> +            break;
>>> +
>>> +        rxd = *rxdp;
>>> +
>>> +        PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_id=%u "
>>> +                  "staterr=0x%x data_len=%u",
>>> +               rxq->port_id, rxq->queue_id, rx_id, staterr,
>>> +               rte_le_to_cpu_16(rxd.wb.upper.length));
>>> +
>>> +        if (!bulk_alloc) {
>>> +            nmb = rte_rxmbuf_alloc(rxq->mb_pool);
>>> +            if (nmb == NULL) {
>>> +                PMD_RX_LOG(DEBUG, "RX mbuf alloc failed "
>>> +                          "port_id=%u queue_id=%u",
>>> +                       rxq->port_id, rxq->queue_id);
>>> +
>>> +                rte_eth_devices[rxq->port_id].data->
>>> +                            rx_mbuf_alloc_failed++;
>>> +                break;
>>> +            }
>>> +        } else if (nb_hold > rxq->rx_free_thresh) {
>>> +            uint16_t next_rdt = rxq->rx_free_trigger;
>>> +
>>> +            if (!ixgbe_rx_alloc_bufs(rxq, false)) {
>>> +                rte_wmb();
>>> +                IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr,
>>> +                            next_rdt);
>>> +                nb_hold -= rxq->rx_free_thresh;
>>> +            } else {
>>> +                PMD_RX_LOG(DEBUG, "RX bulk alloc failed "
>>> +                          "port_id=%u queue_id=%u",
>>> +                       rxq->port_id, rxq->queue_id);
>>> +
>>> +                rte_eth_devices[rxq->port_id].data->
>>> +                            rx_mbuf_alloc_failed++;
>>> +                break;
>>> +            }
>>> +        }
>>> +
>>> +        nb_hold++;
>>> +        rxe = &sw_ring[rx_id];
>>> +        eop = staterr & IXGBE_RXDADV_STAT_EOP;
>>> +
>>> +        next_id = rx_id + 1;
>>> +        if (next_id == rxq->nb_rx_desc)
>>> +            next_id = 0;
>>> +
>>> +        /* Prefetch next mbuf while processing current one. */
>>> +        rte_ixgbe_prefetch(sw_ring[next_id].mbuf);
>>> +
>>> +        /*
>>> +         * When next RX descriptor is on a cache-line boundary,
>>> +         * prefetch the next 4 RX descriptors and the next 4 pointers
>>> +         * to mbufs.
>>> +         */
>>> +        if ((next_id & 0x3) == 0) {
>>> +            rte_ixgbe_prefetch(&rx_ring[next_id]);
>>> +            rte_ixgbe_prefetch(&sw_ring[next_id]);
>>> +        }
>>> +
>>> +        rxm = rxe->mbuf;
>>> +
>>> +        if (!bulk_alloc) {
>>> +            __le64 dma =
>>> + rte_cpu_to_le_64(RTE_MBUF_DATA_DMA_ADDR_DEFAULT(nmb));
>>> +            /*
>>> +             * Update RX descriptor with the physical address of the
>>> +             * new data buffer of the new allocated mbuf.
>>> +             */
>>> +            rxe->mbuf = nmb;
>>> +
>>> +            rxm->data_off = RTE_PKTMBUF_HEADROOM;
>>> +            rxdp->read.hdr_addr = dma;
>>> +            rxdp->read.pkt_addr = dma;
>>> +        } else
>>> +            rxe->mbuf = NULL;
>>> +
>>> +        /*
>>> +         * Set data length & data buffer address of mbuf.
>>> +         */
>>> +        data_len = rte_le_to_cpu_16(rxd.wb.upper.length);
>>> +        rxm->data_len = data_len;
>>> +
>>> +        if (!eop) {
>>> +            uint16_t nextp_id;
>>> +            /*
>>> +             * Get next descriptor index:
>>> +             *  - For RSC it's in the NEXTP field.
>>> +             *  - For a scattered packet - it's just a following
>>> +             *    descriptor.
>>> +             */
>>> +            if (ixgbe_rsc_count(&rxd))
>>> +                nextp_id =
>>> +                    (staterr & IXGBE_RXDADV_NEXTP_MASK) >>
>>> +                               IXGBE_RXDADV_NEXTP_SHIFT;
>>> +            else
>>> +                nextp_id = next_id;
>>> +
>>> +            next_rsc_entry = &sw_rsc_ring[nextp_id];
>>> +            next_rxe = &sw_ring[nextp_id];
>>> +            rte_ixgbe_prefetch(next_rxe);
>>> +        }
>>> +
>>> +        rsc_entry = &sw_rsc_ring[rx_id];
>>> +        first_seg = rsc_entry->fbuf;
>>> +        rsc_entry->fbuf = NULL;
>>> +
>>> +        /*
>>> +         * If this is the first buffer of the received packet,
>>> +         * set the pointer to the first mbuf of the packet and
>>> +         * initialize its context.
>>> +         * Otherwise, update the total length and the number of 
>>> segments
>>> +         * of the current scattered packet, and update the pointer to
>>> +         * the last mbuf of the current packet.
>>> +         */
>>> +        if (first_seg == NULL) {
>>> +            first_seg = rxm;
>>> +            first_seg->pkt_len = data_len;
>>> +            first_seg->nb_segs = 1;
>>> +        } else {
>>> +            first_seg->pkt_len += data_len;
>>> +            first_seg->nb_segs++;
>>> +        }
>>> +
>>> +        prev_id = rx_id;
>>> +        rx_id = next_id;
>>> +
>>> +        /*
>>> +         * If this is not the last buffer of the received packet, 
>>> update
>>> +         * the pointer to the first mbuf at the NEXTP entry in the
>>> +         * sw_rsc_ring and continue to parse the RX ring.
>>> +         */
>>> +        if (!eop) {
>>> +            rxm->next = next_rxe->mbuf;
>>> +            next_rsc_entry->fbuf = first_seg;
>>> +            goto next_desc;
>>> +        }
>>> +
>>> +        /*
>>> +         * This is the last buffer of the received packet - return
>>> +         * the current cluster to the user.
>>> +         */
>>> +        rxm->next = NULL;
>>> +
>>> +        /* Initialize the first mbuf of the returned packet */
>>> +        ixgbe_fill_cluster_head_buf(first_seg, &rxd, rxq->port_id,
>>> +                        staterr);
>>> +
>>> +        /* Prefetch data of first segment, if configured to do so. */
>>> +        rte_packet_prefetch((char *)first_seg->buf_addr +
>>> +            first_seg->data_off);
>>> +
>>> +        /*
>>> +         * Store the mbuf address into the next entry of the array
>>> +         * of returned packets.
>>> +         */
>>> +        rx_pkts[nb_rx++] = first_seg;
>>> +    }
>>> +
>>> +    /*
>>> +     * Record index of the next RX descriptor to probe.
>>> +     */
>>> +    rxq->rx_tail = rx_id;
>>> +
>>> +    /*
>>> +     * If the number of free RX descriptors is greater than the RX 
>>> free
>>> +     * threshold of the queue, advance the Receive Descriptor Tail 
>>> (RDT)
>>> +     * register.
>>> +     * Update the RDT with the value of the last processed RX 
>>> descriptor
>>> +     * minus 1, to guarantee that the RDT register is never equal 
>>> to the
>>> +     * RDH register, which creates a "full" ring situtation from the
>>> +     * hardware point of view...
>>> +     */
>>> +    if (!bulk_alloc && nb_hold > rxq->rx_free_thresh) {
>>> +        PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_tail=%u "
>>> +               "nb_hold=%u nb_rx=%u",
>>> +               rxq->port_id, rxq->queue_id, rx_id, nb_hold, nb_rx);
>>> +
>>> +        rte_wmb();
>>> +        IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr, prev_id);
>>> +        nb_hold = 0;
>>> +    }
>>> +
>>> +    rxq->nb_rx_hold = nb_hold;
>>> +    return nb_rx;
>>> +}
>>> +
>>> +uint16_t
>>> +ixgbe_recv_pkts_lro_single_alloc(void *rx_queue, struct rte_mbuf 
>>> **rx_pkts,
>>> +                 uint16_t nb_pkts)
>>> +{
>>> +    return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, false);
>>> +}
>>> +
>>> +uint16_t
>>> +ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue, struct rte_mbuf 
>>> **rx_pkts,
>>> +                   uint16_t nb_pkts)
>>> +{
>>> +    return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, true);
>>> +}
>>> +
>>>   uint16_t
>>>   ixgbe_recv_scattered_pkts(void *rx_queue, struct rte_mbuf **rx_pkts,
>>>                 uint16_t nb_pkts)
>>> @@ -2005,6 +2295,31 @@ ixgbe_dev_tx_queue_setup(struct rte_eth_dev 
>>> *dev,
>>>       return (0);
>>>   }
>>>
>>> +/**
>>> + * ixgbe_free_rsc_cluster - free the not-yet-completed RSC cluster
>>> + *
>>> + * The "next" pointer of the last segment of (not-yet-completed) 
>>> RSC clusters
>>> + * in the sw_rsc_ring is not set to NULL but rather points to the next
>>> + * mbuf of this RSC aggregation (that has not been completed yet 
>>> and still
>>> + * resides on the HW ring). So, instead of calling for 
>>> rte_pktmbuf_free() we
>>> + * will just free first "nb_segs" segments of the cluster 
>>> explicitly by calling
>>> + * an rte_pktmbuf_free_seg().
>>> + *
>>> + * @m RSC cluster head
>>> + */
>>> +static void
>>> +ixgbe_free_rsc_cluster(struct rte_mbuf *m)
>>> +{
>>> +    uint8_t i, nb_segs = m->nb_segs;
>>> +    struct rte_mbuf *next_seg;
>>> +
>>> +    for (i = 0; i < nb_segs; i++) {
>>> +        next_seg = m->next;
>>> +        rte_pktmbuf_free_seg(m);
>>> +        m = next_seg;
>>> +    }
>>> +}
>>> +
>>>   static void
>>>   ixgbe_rx_queue_release_mbufs(struct ixgbe_rx_queue *rxq)
>>>   {
>>> @@ -2028,6 +2343,13 @@ ixgbe_rx_queue_release_mbufs(struct 
>>> ixgbe_rx_queue *rxq)
>>>           }
>>>   #endif
>>>       }
>>> +
>>> +    if (rxq->sw_rsc_ring)
>>> +        for (i = 0; i < rxq->nb_rx_desc; i++)
>>> +            if (rxq->sw_rsc_ring[i].fbuf) {
>>> + ixgbe_free_rsc_cluster(rxq->sw_rsc_ring[i].fbuf);
>>> +                rxq->sw_rsc_ring[i].fbuf = NULL;
>>> +            }
>>>   }
>>>
>>>   static void
>>> @@ -2036,6 +2358,7 @@ ixgbe_rx_queue_release(struct ixgbe_rx_queue 
>>> *rxq)
>>>       if (rxq != NULL) {
>>>           ixgbe_rx_queue_release_mbufs(rxq);
>>>           rte_free(rxq->sw_ring);
>>> +        rte_free(rxq->sw_rsc_ring);
>>>           rte_free(rxq);
>>>       }
>>>   }
>>> @@ -2158,6 +2481,7 @@ ixgbe_reset_rx_queue(struct ixgbe_hw *hw, 
>>> struct ixgbe_rx_queue *rxq)
>>>       rxq->nb_rx_hold = 0;
>>>       rxq->pkt_first_seg = NULL;
>>>       rxq->pkt_last_seg = NULL;
>>> +    rxq->rsc_en = 0;
>>>   }
>>>
>>>   int
>>> @@ -2172,6 +2496,14 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev 
>>> *dev,
>>>       struct ixgbe_rx_queue *rxq;
>>>       struct ixgbe_hw     *hw;
>>>       uint16_t len;
>>> +    struct rte_eth_dev_info dev_info = { 0 };
>>> +    struct rte_eth_rxmode *dev_rx_mode = &dev->data->dev_conf.rxmode;
>>> +    bool rsc_requested = false;
>>> +
>>> +    dev->dev_ops->dev_infos_get(dev, &dev_info);
>>> +    if ((dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO) &&
>>> +        dev_rx_mode->enable_lro)
>>> +        rsc_requested = true;
>>>
>>>       PMD_INIT_FUNC_TRACE();
>>>       hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>>> @@ -2277,12 +2609,27 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev 
>>> *dev,
>>>       rxq->sw_ring = rte_zmalloc_socket("rxq->sw_ring",
>>>                         sizeof(struct ixgbe_rx_entry) * len,
>>>                         RTE_CACHE_LINE_SIZE, socket_id);
>>> -    if (rxq->sw_ring == NULL) {
>>> +    if (!rxq->sw_ring) {
>>>           ixgbe_rx_queue_release(rxq);
>>>           return (-ENOMEM);
>>>       }
>>> -    PMD_INIT_LOG(DEBUG, "sw_ring=%p hw_ring=%p dma_addr=0x%"PRIx64,
>>> -             rxq->sw_ring, rxq->rx_ring, rxq->rx_ring_phys_addr);
>>> +
>>> +    if (rsc_requested) {
>>> +        rxq->sw_rsc_ring =
>>> +            rte_zmalloc_socket("rxq->sw_rsc_ring",
>>> +                       sizeof(struct ixgbe_rsc_entry) * len,
>>> +                       RTE_CACHE_LINE_SIZE, socket_id);
>>> +        if (!rxq->sw_rsc_ring) {
>>> +            ixgbe_rx_queue_release(rxq);
>>> +            return (-ENOMEM);
>>> +        }
>>> +    } else
>>> +        rxq->sw_rsc_ring = NULL;
>>> +
>>> +    PMD_INIT_LOG(DEBUG, "sw_ring=%p sw_rsc_ring=%p hw_ring=%p "
>>> +                "dma_addr=0x%"PRIx64,
>>> +             rxq->sw_ring, rxq->sw_rsc_ring, rxq->rx_ring,
>>> +             rxq->rx_ring_phys_addr);
>>>
>>>       if (!rte_is_power_of_2(nb_desc)) {
>>>           PMD_INIT_LOG(DEBUG, "queue[%d] doesn't meet Vector Rx "
>>> @@ -3527,6 +3874,91 @@ ixgbe_dev_mq_tx_configure(struct rte_eth_dev 
>>> *dev)
>>>       return 0;
>>>   }
>>>
>>> +/**
>>> + * ixgbe_get_rscctl_maxdesc - Calculate the RSCCTL[n].MAXDESC for PF
>>> + *
>>> + * Return the RSCCTL[n].MAXDESC for 82599 and x540 PF devices 
>>> according to the
>>> + * spec rev. 3.0 chapter 8.2.3.8.13.
>>> + *
>>> + * @pool Memory pool of the Rx queue
>>> + */
>>> +static inline uint32_t
>>> +ixgbe_get_rscctl_maxdesc(struct rte_mempool *pool)
>>> +{
>>> +    struct rte_pktmbuf_pool_private *mp_priv = 
>>> rte_mempool_get_priv(pool);
>>> +
>>> +    /* MAXDESC * SRRCTL.BSIZEPKT must not exceed 64 KB minus one */
>>> +    uint16_t maxdesc =
>>> +        IPV4_MAX_PKT_LEN /
>>> +            (mp_priv->mbuf_data_room_size - RTE_PKTMBUF_HEADROOM);
>>> +
>>> +    if (maxdesc >= 16)
>>> +        return IXGBE_RSCCTL_MAXDESC_16;
>>> +    else if (maxdesc >= 8)
>>> +        return IXGBE_RSCCTL_MAXDESC_8;
>>> +    else if (maxdesc >= 4)
>>> +        return IXGBE_RSCCTL_MAXDESC_4;
>>> +    else
>>> +        return IXGBE_RSCCTL_MAXDESC_1;
>>> +}
>>> +
>>> +/**
>>> + * ixgbe_set_ivar - Setup the correct IVAR register for a 
>>> particular MSIX
>>> + * interrupt
>>> + *
>>> + * (Taken from FreeBSD tree)
>>> + * (yes this is all very magic and confusing :)
>>> + *
>>> + * @dev port handle
>>> + * @entry the register array entry
>>> + * @vector the MSIX vector for this queue
>>> + * @type RX/TX/MISC
>>> + */
>>> +static void
>>> +ixgbe_set_ivar(struct rte_eth_dev *dev, u8 entry, u8 vector, s8 type)
>>> +{
>>> +    struct ixgbe_hw *hw = 
>>> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>>> +    u32 ivar, index;
>>> +
>>> +    vector |= IXGBE_IVAR_ALLOC_VAL;
>>> +
>>> +    switch (hw->mac.type) {
>>> +
>>> +    case ixgbe_mac_82598EB:
>>> +        if (type == -1)
>>> +            entry = IXGBE_IVAR_OTHER_CAUSES_INDEX;
>>> +        else
>>> +            entry += (type * 64);
>>> +        index = (entry >> 2) & 0x1F;
>>> +        ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(index));
>>> +        ivar &= ~(0xFF << (8 * (entry & 0x3)));
>>> +        ivar |= (vector << (8 * (entry & 0x3)));
>>> +        IXGBE_WRITE_REG(hw, IXGBE_IVAR(index), ivar);
>>> +        break;
>>> +
>>> +    case ixgbe_mac_82599EB:
>>> +    case ixgbe_mac_X540:
>>> +        if (type == -1) { /* MISC IVAR */
>>> +            index = (entry & 1) * 8;
>>> +            ivar = IXGBE_READ_REG(hw, IXGBE_IVAR_MISC);
>>> +            ivar &= ~(0xFF << index);
>>> +            ivar |= (vector << index);
>>> +            IXGBE_WRITE_REG(hw, IXGBE_IVAR_MISC, ivar);
>>> +        } else {    /* RX/TX IVARS */
>>> +            index = (16 * (entry & 1)) + (8 * type);
>>> +            ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(entry >> 1));
>>> +            ivar &= ~(0xFF << index);
>>> +            ivar |= (vector << index);
>>> +            IXGBE_WRITE_REG(hw, IXGBE_IVAR(entry >> 1), ivar);
>>> +        }
>>> +
>>> +        break;
>>> +
>>> +    default:
>>> +        break;
>>> +    }
>>> +}
>>> +
>>>   void ixgbe_set_rx_function(struct rte_eth_dev *dev)
>>>   {
>>>       struct ixgbe_hw *hw = 
>>> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>>> @@ -3545,7 +3977,24 @@ void ixgbe_set_rx_function(struct rte_eth_dev 
>>> *dev)
>>>           hw->rx_vec_allowed = false;
>>>       }
>>>
>>> -    if (dev->data->scattered_rx) {
>>> +    /*
>>> +     * Initialize the appropriate LRO callback.
>>> +     *
>>> +     * If all queues satisfy the bulk allocation preconditions
>>> +     * (hw->rx_bulk_alloc_allowed is TRUE) then we may use bulk 
>>> allocation.
>>> +     * Otherwise use a single allocation version.
>>> +     */
>>> +    if (dev->data->lro) {
>>> +        if (hw->rx_bulk_alloc_allowed) {
>>> +            PMD_INIT_LOG(INFO, "LRO is requested. Using a bulk "
>>> +                       "allocation version");
>>> +            dev->rx_pkt_burst = ixgbe_recv_pkts_lro_bulk_alloc;
>>> +        } else {
>>> +            PMD_INIT_LOG(INFO, "LRO is requested. Using a single "
>>> +                       "allocation version");
>>> +            dev->rx_pkt_burst = ixgbe_recv_pkts_lro_single_alloc;
>>> +        }
>>> +    } else if (dev->data->scattered_rx) {
>>>           /*
>>>            * Set the non-LRO scattered callback: there are Vector and
>>>            * single allocation versions.
>>> @@ -3595,6 +4044,149 @@ void ixgbe_set_rx_function(struct 
>>> rte_eth_dev *dev)
>>>       }
>>>   }
>>>
>>> +/**
>>> + * ixgbe_set_rsc - configure RSC related port HW registers
>>> + *
>>> + * Configures the port's RSC related registers according to the 
>>> 4.6.7.2 chapter
>>> + * of 82599 Spec (x540 configuration is virtually the same).
>>> + *
>>> + * @dev port handle
>>> + *
>>> + * Returns 0 in case of success or a non-zero error code
>>> + */
>>> +static int
>>> +ixgbe_set_rsc(struct rte_eth_dev *dev)
>>> +{
>>> +    struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
>>> +    struct ixgbe_hw *hw = 
>>> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>>> +    struct rte_eth_dev_info dev_info = { 0 };
>>> +    bool rsc_capable = false;
>>> +    uint16_t i;
>>> +    uint32_t rdrxctl;
>>> +
>>> +    /* Sanity check */
>>> +    dev->dev_ops->dev_infos_get(dev, &dev_info);
>>> +    if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO)
>>> +        rsc_capable = true;
>>> +
>>> +    if (!rsc_capable && rx_conf->enable_lro) {
>>> +        PMD_INIT_LOG(CRIT, "LRO is requested on HW that doesn't "
>>> +                   "support it");
>>> +        return -EINVAL;
>>> +    }
>>> +
>>> +    /* RSC global configuration (chapter 4.6.7.2.1 of 82599 Spec) */
>>> +
>>> +    if (!rx_conf->hw_strip_crc && rx_conf->enable_lro) {
>>> +        /*
>>> +         * According to chapter of 4.6.7.2.1 of the Spec Rev.
>>> +         * 3.0 RSC configuration requires HW CRC stripping being
>>> +         * enabled. If user requested both HW CRC stripping off
>>> +         * and RSC on - return an error.
>>> +         */
>>> +        PMD_INIT_LOG(CRIT, "LRO can't be enabled when HW CRC "
>>> +                    "is disabled");
>>> +        return -EINVAL;
>>> +    }
>>> +
>>> +    /* RFCTL configuration  */
>>> +    if (rsc_capable) {
>>> +        uint32_t rfctl = IXGBE_READ_REG(hw, IXGBE_RFCTL);
>>> +        if (rx_conf->enable_lro)
>>> +            /*
>>> +             * Since NFS packets coalescing is not supported - clear
>>> +             * RFCTL.NFSW_DIS and RFCTL.NFSR_DIS when RSC is
>>> +             * enabled.
>>> +             */
>>> +            rfctl &= ~(IXGBE_RFCTL_RSC_DIS | IXGBE_RFCTL_NFSW_DIS |
>>> +                   IXGBE_RFCTL_NFSR_DIS);
>>> +        else
>>> +            rfctl |= IXGBE_RFCTL_RSC_DIS;
>>> +
>>> +        IXGBE_WRITE_REG(hw, IXGBE_RFCTL, rfctl);
>>> +    }
>>> +
>>> +    /* If LRO hasn't been requested - we are done here. */
>>> +    if (!rx_conf->enable_lro)
>>> +        return 0;
>>> +
>>> +    /* Set RDRXCTL.RSCACKC bit */
>>> +    rdrxctl = IXGBE_READ_REG(hw, IXGBE_RDRXCTL);
>>> +    rdrxctl |= IXGBE_RDRXCTL_RSCACKC;
>>> +    IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
>>> +
>>> +    /* Per-queue RSC configuration (chapter 4.6.7.2.2 of 82599 
>>> Spec) */
>>> +    for (i = 0; i < dev->data->nb_rx_queues; i++) {
>>> +        struct ixgbe_rx_queue *rxq = dev->data->rx_queues[i];
>>> +        uint32_t srrctl =
>>> +            IXGBE_READ_REG(hw, IXGBE_SRRCTL(rxq->reg_idx));
>>> +        uint32_t rscctl =
>>> +            IXGBE_READ_REG(hw, IXGBE_RSCCTL(rxq->reg_idx));
>>> +        uint32_t psrtype =
>>> +            IXGBE_READ_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx));
>>> +        uint32_t eitr =
>>> +            IXGBE_READ_REG(hw, IXGBE_EITR(rxq->reg_idx));
>>> +
>>> +        /*
>>> +         * ixgbe PMD doesn't support header-split at the moment.
>>> +         *
>>> +         * Following the 4.6.7.2.1 chapter of the 82599/x540
>>> +         * Spec if RSC is enabled the SRRCTL[n].BSIZEHEADER
>>> +         * should be configured even if header split is not
>>> +         * enabled. We will configure it 128 bytes following the
>>> +         * recommendation in the spec.
>>> +         */
>>> +        srrctl &= ~IXGBE_SRRCTL_BSIZEHDR_MASK;
>>> +        srrctl |= (128 << IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT) &
>>> +                        IXGBE_SRRCTL_BSIZEHDR_MASK;
>>> +
>>> +        /*
>>> +         * TODO: Consider setting the Receive Descriptor Minimum
>>> +         * Threshold Size for an RSC case. This is not an obviously
>>> +         * beneficiary option but the one worth considering...
>>> +         */
>>> +
>>> +        rscctl |= IXGBE_RSCCTL_RSCEN;
>>> +        rscctl |= ixgbe_get_rscctl_maxdesc(rxq->mb_pool);
>>> +        psrtype |= IXGBE_PSRTYPE_TCPHDR;
>>> +
>>> +        /*
>>> +         * RSC: Set ITR interval corresponding to 2K ints/s.
>>> +         *
>>> +         * Full-sized RSC aggregations for a 10Gb/s link will
>>> +         * arrive at about 20K aggregation/s rate.
>>> +         *
>>> +         * 2K inst/s rate will make only 10% of the
>>> +         * aggregations to be closed due to the interrupt timer
>>> +         * expiration for a streaming at wire-speed case.
>>> +         *
>>> +         * For a sparse streaming case this setting will yield
>>> +         * at most 500us latency for a single RSC aggregation.
>>> +         */
>>> +        eitr &= ~IXGBE_EITR_ITR_INT_MASK;
>>> +        eitr |= IXGBE_EITR_INTERVAL_US(500) | IXGBE_EITR_CNT_WDIS;
>>> +
>>> +        IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
>>> +        IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(rxq->reg_idx), rscctl);
>>> +        IXGBE_WRITE_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx), psrtype);
>>> +        IXGBE_WRITE_REG(hw, IXGBE_EITR(rxq->reg_idx), eitr);
>>> +
>>> +        /*
>>> +         * RSC requires the mapping of the queue to the
>>> +         * interrupt vector.
>>> +         */
>>> +        ixgbe_set_ivar(dev, rxq->reg_idx, i, 0);
>>> +
>>> +        rxq->rsc_en = 1;
>>> +    }
>>> +
>>> +    dev->data->lro = 1;
>>> +
>>> +    PMD_INIT_LOG(INFO, "enabling LRO mode");
>>> +
>>> +    return 0;
>>> +}
>>> +
>>>   /*
>>>    * Initializes Receive Unit.
>>>    */
>>> @@ -3615,6 +4207,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>>       uint16_t buf_size;
>>>       uint16_t i;
>>>       struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
>>> +    int rc;
>>>
>>>       PMD_INIT_FUNC_TRACE();
>>>       hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>>> @@ -3724,6 +4317,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>>                          RTE_PKTMBUF_HEADROOM);
>>>           srrctl |= ((buf_size >> IXGBE_SRRCTL_BSIZEPKT_SHIFT) &
>>>                  IXGBE_SRRCTL_BSIZEPKT_MASK);
>>> +
>>>           IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
>>>
>>>           buf_size = (uint16_t) ((srrctl & 
>>> IXGBE_SRRCTL_BSIZEPKT_MASK) <<
>>> @@ -3738,8 +4332,6 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>>       if (rx_conf->enable_scatter)
>>>           dev->data->scattered_rx = 1;
>>>
>>> -    ixgbe_set_rx_function(dev);
>>> -
>>>       /*
>>>        * Device configured with multiple RX queues.
>>>        */
>>> @@ -3770,6 +4362,12 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>>           IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
>>>       }
>>>
>>> +    rc = ixgbe_set_rsc(dev);
>>> +    if (rc)
>>> +        return rc;
>>> +
>>> +    ixgbe_set_rx_function(dev);
>>> +
>>>       return 0;
>>>   }
>>>
>>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h 
>>> b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
>>> index 3937cf6..120bbbd 100644
>>> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
>>> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
>>> @@ -79,6 +79,10 @@ struct ixgbe_rx_entry {
>>>       struct rte_mbuf *mbuf; /**< mbuf associated with RX 
>>> descriptor. */
>>>   };
>>>
>>> +struct ixgbe_rsc_entry {
>>> +    struct rte_mbuf *fbuf; /**< First segment of the fragmented 
>>> packet. */
>>> +};
>>> +
>>>   /**
>>>    * Structure associated with each descriptor of the TX ring of a 
>>> TX queue.
>>>    */
>>> @@ -105,6 +109,7 @@ struct ixgbe_rx_queue {
>>>       volatile uint32_t   *rdt_reg_addr; /**< RDT register address. */
>>>       volatile uint32_t   *rdh_reg_addr; /**< RDH register address. */
>>>       struct ixgbe_rx_entry *sw_ring; /**< address of RX software 
>>> ring. */
>>> +    struct ixgbe_rsc_entry *sw_rsc_ring; /**< address of RSC 
>>> software ring. */
>>>       struct rte_mbuf *pkt_first_seg; /**< First segment of current 
>>> packet. */
>>>       struct rte_mbuf *pkt_last_seg; /**< Last segment of current 
>>> packet. */
>>>       uint64_t            mbuf_initializer; /**< value to init mbufs */
>>> @@ -126,6 +131,7 @@ struct ixgbe_rx_queue {
>>>       uint8_t             port_id;  /**< Device port identifier. */
>>>       uint8_t             crc_len;  /**< 0 if CRC stripped, 4 
>>> otherwise. */
>>>       uint8_t             drop_en;  /**< If not 0, set 
>>> SRRCTL.Drop_En. */
>>> +    uint8_t             rsc_en;   /**< If not 0, RSC is enabled. */
>>>       uint8_t             rx_deferred_start; /**< not in global dev 
>>> start. */
>>>   #ifdef RTE_LIBRTE_IXGBE_RX_ALLOW_BULK_ALLOC
>>>       /** need to alloc dummy mbuf, for wraparound when scanning hw 
>>> ring */
>>> -- 
>>> 2.1.0
>

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
  2015-03-30 14:18   ` Ananyev, Konstantin
@ 2015-03-30 15:37     ` Vlad Zolotarov
  2015-03-30 15:57       ` Vlad Zolotarov
  0 siblings, 1 reply; 6+ messages in thread
From: Vlad Zolotarov @ 2015-03-30 15:37 UTC (permalink / raw)
  To: Ananyev, Konstantin, dev



On 03/30/15 17:18, Ananyev, Konstantin wrote:
> Hi Vlad,
>
>> -----Original Message-----
>> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Vlad Zolotarov
>> Sent: Wednesday, March 18, 2015 5:52 PM
>> To: dev@dpdk.org
>> Subject: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
>>
>>      - Only x540 and 82599 devices support LRO.
>>      - Add the appropriate HW configuration.
>>      - Add RSC aware rx_pkt_burst() handlers:
>>         - Implemented bulk allocation and non-bulk allocation versions.
>>         - Add LRO-specific fields to rte_eth_rxmode, to rte_eth_dev_data
>>           and to ixgbe_rx_queue.
>>         - Use the appropriate handler when LRO is requested.
>>
>> Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
>> ---
>> New in v8:
>>     - Took the RSC configuration code from ixgbe_dev_rx_init() into a separate
>>       function - ixgbe_set_rsc().
>>     - Added some missing macros for HW configuration.
>>     - Styling adjustments:
>>        - Functions names.
>>        - Functions descriptions.
>>     - Reworked the ixgbe_free_rsc_cluster() code to make it more readable.
>>     - Kill the HEADER_SPLIT flow in ixgbe_set_rsc() since it's not supported by
>>       ixgbe PMD.
>>
>> New in v7:
>>     - Free not-yet-completed RSC aggregations in rte_eth_dev_stop() flow.
>>     - Reset the sw_ring[].mbuf entry in a bulk allocation case.
>>       This is needed for ixgbe_rx_queue_release_mbufs().
>>     - _recv_pkts_lro(): added the missing memory barrier before RDT update in a
>>       non-bulk allocation case.
>>     - Don't allow RSC when device is configured in an SR-IOV mode.
>>
>> New in v5:
>>     - Put the RTE_ETHDEV_HAS_LRO_SUPPORT definition at the beginning of rte_ethdev.h.
>>     - Removed the "TODO: Remove me" comment near RTE_ETHDEV_HAS_LRO_SUPPORT.
>>
>> New in v4:
>>     - Define RTE_ETHDEV_HAS_LRO_SUPPORT in rte_ethdev.h instead of
>>       RTE_ETHDEV_LRO_SUPPORT defined in config/common_linuxapp.
>>
>> New in v2:
>>     - Removed rte_eth_dev_data.lro_bulk_alloc.
>>     - Fixed a few styling and spelling issues.
>> ---
>>   lib/librte_ether/rte_ethdev.h           |   9 +-
>>   lib/librte_net/rte_ip.h                 |   3 +
>>   lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h |   6 +
>>   lib/librte_pmd_ixgbe/ixgbe_ethdev.c     |  11 +
>>   lib/librte_pmd_ixgbe/ixgbe_ethdev.h     |   5 +
>>   lib/librte_pmd_ixgbe/ixgbe_rxtx.c       | 610 +++++++++++++++++++++++++++++++-
>>   lib/librte_pmd_ixgbe/ixgbe_rxtx.h       |   6 +
>>   7 files changed, 642 insertions(+), 8 deletions(-)
>>
>> diff --git a/lib/librte_ether/rte_ethdev.h b/lib/librte_ether/rte_ethdev.h
>> index 21aa359..61dc49a 100644
>> --- a/lib/librte_ether/rte_ethdev.h
>> +++ b/lib/librte_ether/rte_ethdev.h
>> @@ -172,6 +172,9 @@ extern "C" {
>>
>>   #include <stdint.h>
>>
>> +/* Use this macro to check if LRO API is supported */
>> +#define RTE_ETHDEV_HAS_LRO_SUPPORT
>> +
>>   #include <rte_log.h>
>>   #include <rte_interrupts.h>
>>   #include <rte_pci.h>
>> @@ -320,14 +323,15 @@ struct rte_eth_rxmode {
>>   	enum rte_eth_rx_mq_mode mq_mode;
>>   	uint32_t max_rx_pkt_len;  /**< Only used if jumbo_frame enabled. */
>>   	uint16_t split_hdr_size;  /**< hdr buf size (header_split enabled).*/
>> -	uint8_t header_split : 1, /**< Header Split enable. */
>> +	uint16_t header_split : 1, /**< Header Split enable. */
>>   		hw_ip_checksum   : 1, /**< IP/UDP/TCP checksum offload enable. */
>>   		hw_vlan_filter   : 1, /**< VLAN filter enable. */
>>   		hw_vlan_strip    : 1, /**< VLAN strip enable. */
>>   		hw_vlan_extend   : 1, /**< Extended VLAN enable. */
>>   		jumbo_frame      : 1, /**< Jumbo Frame Receipt enable. */
>>   		hw_strip_crc     : 1, /**< Enable CRC stripping by hardware. */
>> -		enable_scatter   : 1; /**< Enable scatter packets rx handler */
>> +		enable_scatter   : 1, /**< Enable scatter packets rx handler */
>> +		enable_lro       : 1; /**< Enable LRO */
>>   };
>>
>>   /**
>> @@ -1515,6 +1519,7 @@ struct rte_eth_dev_data {
>>   	uint8_t port_id;           /**< Device [external] port identifier. */
>>   	uint8_t promiscuous   : 1, /**< RX promiscuous mode ON(1) / OFF(0). */
>>   		scattered_rx : 1,  /**< RX of scattered packets is ON(1) / OFF(0) */
>> +		lro          : 1,  /**< RX LRO is ON(1) / OFF(0) */
>>   		all_multicast : 1, /**< RX all multicast mode ON(1) / OFF(0). */
>>   		dev_started : 1;   /**< Device state: STARTED(1) / STOPPED(0). */
>>   };
>> diff --git a/lib/librte_net/rte_ip.h b/lib/librte_net/rte_ip.h
>> index 64935d9..74c9ced 100644
>> --- a/lib/librte_net/rte_ip.h
>> +++ b/lib/librte_net/rte_ip.h
>> @@ -110,6 +110,9 @@ struct ipv4_hdr {
>>   					   (((c) & 0xff) << 8)  | \
>>   					   ((d) & 0xff))
>>
>> +/** Maximal IPv4 packet length (including a header) */
>> +#define IPV4_MAX_PKT_LEN        65535
>> +
>>   /** Internet header length mask for version_ihl field */
>>   #define IPV4_HDR_IHL_MASK	(0x0f)
>>   /**
>> diff --git a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
>> index 9a66370..4998627 100644
>> --- a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
>> +++ b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
>> @@ -234,8 +234,14 @@ struct ixgbe_thermal_sensor_data {
>>   #define IXGBE_EITR(_i)		(((_i) <= 23) ? (0x00820 + ((_i) * 4)) : \
>>   				 (0x012300 + (((_i) - 24) * 4)))
>>   #define IXGBE_EITR_ITR_INT_MASK	0x00000FF8
>> +#define IXGBE_EITR_ITR_INT_SHIFT 3
>>   #define IXGBE_EITR_LLI_MOD	0x00008000
>>   #define IXGBE_EITR_CNT_WDIS	0x80000000
>> +/* EITR Inteval is in 2048ns uinits for 1G and 10G link */
>> +#define IXGBE_EITR_INTERVAL_UNIT_NS	2048
> Why is that? Why not just 2us as 82599 spec says?
> And then:
> +#define IXGBE_EITR_INTERVAL_US(us) (((us) / IXGBE_EITR_INTERVAL_UNIT_US << IXGBE_EITR_ITR_INT_SHIFT) & IXGBE_EITR_ITR_INT_MASK)
> ?

Because spec doesn't say 2us but rather 2.048us - see 8.2.4.5.16 chapter 
of x540 spec.

>
>> +#define IXGBE_EITR_INTERVAL_US(us)	\
>> +   (((us) * 1000 / IXGBE_EITR_INTERVAL_UNIT_NS << IXGBE_EITR_ITR_INT_SHIFT) & \
>> +		IXGBE_EITR_ITR_INT_MASK)
>
> Unfortunately we are not supposed to change files under ixgbe subfirectory (except ixgbe_osdep.*).
> These files comes from ixgbe shared code and we treat them as read-only.
> You need to move these new macros you added into ixgbe_ethedev.h.

Aha... Ok. No problem.

>
> All other things look good to me.
> Konstantin
>
>>   #define IXGBE_IVAR(_i)		(0x00900 + ((_i) * 4)) /* 24 at 0x900-0x960 */
>>   #define IXGBE_IVAR_MISC		0x00A00 /* misc MSI-X interrupt causes */
>>   #define IXGBE_EITRSEL		0x00894
>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>> index 92d75db..923692e 100644
>> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
>> @@ -1645,6 +1645,7 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
>>
>>   	/* Clear stored conf */
>>   	dev->data->scattered_rx = 0;
>> +	dev->data->lro = 0;
>>
>>   	/* Clear recorded link status */
>>   	memset(&link, 0, sizeof(link));
>> @@ -2013,6 +2014,16 @@ ixgbe_dev_info_get(struct rte_eth_dev *dev, struct rte_eth_dev_info *dev_info)
>>   		DEV_RX_OFFLOAD_IPV4_CKSUM |
>>   		DEV_RX_OFFLOAD_UDP_CKSUM  |
>>   		DEV_RX_OFFLOAD_TCP_CKSUM;
>> +
>> +	/*
>> +	 * RSC is only supported by 82599 and x540 PF devices in a non-SR-IOV
>> +	 * mode.
>> +	 */
>> +	if ((hw->mac.type == ixgbe_mac_82599EB ||
>> +	     hw->mac.type == ixgbe_mac_X540) &&
>> +	    !RTE_ETH_DEV_SRIOV(dev).active)
>> +		dev_info->rx_offload_capa |= DEV_RX_OFFLOAD_TCP_LRO;
>> +
>>   	dev_info->tx_offload_capa =
>>   		DEV_TX_OFFLOAD_VLAN_INSERT |
>>   		DEV_TX_OFFLOAD_IPV4_CKSUM  |
>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>> index ffe3471..7050340 100644
>> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
>> @@ -344,6 +344,11 @@ uint16_t ixgbe_recv_pkts(void *rx_queue, struct rte_mbuf **rx_pkts,
>>   uint16_t ixgbe_recv_scattered_pkts(void *rx_queue,
>>   		struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
>>
>> +uint16_t ixgbe_recv_pkts_lro_single_alloc(void *rx_queue,
>> +		struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
>> +uint16_t ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue,
>> +		struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
>> +
>>   uint16_t ixgbe_xmit_pkts(void *tx_queue, struct rte_mbuf **tx_pkts,
>>   		uint16_t nb_pkts);
>>
>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
>> index a08ae6a..daa4c45 100644
>> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
>> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
>> @@ -70,6 +70,7 @@
>>   #include <rte_sctp.h>
>>   #include <rte_string_fns.h>
>>   #include <rte_errno.h>
>> +#include <rte_ip.h>
>>
>>   #include "ixgbe_logs.h"
>>   #include "ixgbe/ixgbe_api.h"
>> @@ -1422,6 +1423,295 @@ ixgbe_fill_cluster_head_buf(
>>   	}
>>   }
>>
>> +/**
>> + * ixgbe_recv_pkts_lro - receive handler for and LRO case.
>> + *
>> + * @rx_queue Rx queue handle
>> + * @rx_pkts table of received packets
>> + * @nb_pkts size of rx_pkts table
>> + * @bulk_alloc if TRUE bulk allocation is used for a HW ring refilling
>> + *
>> + * Handles the Rx HW ring completions when RSC feature is configured. Uses an
>> + * additional ring of ixgbe_rsc_entry's that will hold the relevant RSC info.
>> + *
>> + * We use the same logic as in Lunux and in FreeBSD ixgbe drivers:
>> + * 1) When non-EOP RSC completion arrives:
>> + *    a) Update the HEAD of the current RSC aggregation cluster with the new
>> + *       segment's data length.
>> + *    b) Set the "next" pointer of the current segment to point to the segment
>> + *       at the NEXTP index.
>> + *    c) Pass the HEAD of RSC aggregation cluster on to the next NEXTP entry
>> + *       in the sw_rsc_ring.
>> + * 2) When EOP arrives we just update the cluster's total length and offload
>> + *    flags and deliver the cluster up to the upper layers. In our case - put it
>> + *    in the rx_pkts table.
>> + *
>> + * Returns the number of received packets/clusters (according to the "bulk
>> + * receive" interface).
>> + */
>> +static inline uint16_t
>> +ixgbe_recv_pkts_lro(void *rx_queue, struct rte_mbuf **rx_pkts, uint16_t nb_pkts,
>> +		    bool bulk_alloc)
>> +{
>> +	struct ixgbe_rx_queue *rxq = rx_queue;
>> +	volatile union ixgbe_adv_rx_desc *rx_ring = rxq->rx_ring;
>> +	struct ixgbe_rx_entry *sw_ring = rxq->sw_ring;
>> +	struct ixgbe_rsc_entry *sw_rsc_ring = rxq->sw_rsc_ring;
>> +	uint16_t rx_id = rxq->rx_tail;
>> +	uint16_t nb_rx = 0;
>> +	uint16_t nb_hold = rxq->nb_rx_hold;
>> +	uint16_t prev_id = rxq->rx_tail;
>> +
>> +	while (nb_rx < nb_pkts) {
>> +		bool eop;
>> +		struct ixgbe_rx_entry *rxe;
>> +		struct ixgbe_rsc_entry *rsc_entry;
>> +		struct ixgbe_rsc_entry *next_rsc_entry;
>> +		struct ixgbe_rx_entry *next_rxe;
>> +		struct rte_mbuf *first_seg;
>> +		struct rte_mbuf *rxm;
>> +		struct rte_mbuf *nmb;
>> +		union ixgbe_adv_rx_desc rxd;
>> +		uint16_t data_len;
>> +		uint16_t next_id;
>> +		volatile union ixgbe_adv_rx_desc *rxdp;
>> +		uint32_t staterr;
>> +
>> +next_desc:
>> +		/*
>> +		 * The code in this whole file uses the volatile pointer to
>> +		 * ensure the read ordering of the status and the rest of the
>> +		 * descriptor fields (on the compiler level only!!!). This is so
>> +		 * UGLY - why not to just use the compiler barrier instead? DPDK
>> +		 * even has the rte_compiler_barrier() for that.
>> +		 *
>> +		 * But most importantly this is just wrong because this doesn't
>> +		 * ensure memory ordering in a general case at all. For
>> +		 * instance, DPDK is supposed to work on Power CPUs where
>> +		 * compiler barrier may just not be enough!
>> +		 *
>> +		 * I tried to write only this function properly to have a
>> +		 * starting point (as a part of an LRO/RSC series) but the
>> +		 * compiler cursed at me when I tried to cast away the
>> +		 * "volatile" from rx_ring (yes, it's volatile too!!!). So, I'm
>> +		 * keeping it the way it is for now.
>> +		 *
>> +		 * The code in this file is broken in so many other places and
>> +		 * will just not work on a big endian CPU anyway therefore the
>> +		 * lines below will have to be revisited together with the rest
>> +		 * of the ixgbe PMD.
>> +		 *
>> +		 * TODO:
>> +		 *    - Get rid of "volatile" crap and let the compiler do its
>> +		 *      job.
>> +		 *    - Use the proper memory barrier (rte_rmb()) to ensure the
>> +		 *      memory ordering below.
>> +		 */
>> +		rxdp = &rx_ring[rx_id];
>> +		staterr = rte_le_to_cpu_32(rxdp->wb.upper.status_error);
>> +
>> +		if (!(staterr & IXGBE_RXDADV_STAT_DD))
>> +			break;
>> +
>> +		rxd = *rxdp;
>> +
>> +		PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_id=%u "
>> +				  "staterr=0x%x data_len=%u",
>> +			   rxq->port_id, rxq->queue_id, rx_id, staterr,
>> +			   rte_le_to_cpu_16(rxd.wb.upper.length));
>> +
>> +		if (!bulk_alloc) {
>> +			nmb = rte_rxmbuf_alloc(rxq->mb_pool);
>> +			if (nmb == NULL) {
>> +				PMD_RX_LOG(DEBUG, "RX mbuf alloc failed "
>> +						  "port_id=%u queue_id=%u",
>> +					   rxq->port_id, rxq->queue_id);
>> +
>> +				rte_eth_devices[rxq->port_id].data->
>> +							rx_mbuf_alloc_failed++;
>> +				break;
>> +			}
>> +		} else if (nb_hold > rxq->rx_free_thresh) {
>> +			uint16_t next_rdt = rxq->rx_free_trigger;
>> +
>> +			if (!ixgbe_rx_alloc_bufs(rxq, false)) {
>> +				rte_wmb();
>> +				IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr,
>> +						    next_rdt);
>> +				nb_hold -= rxq->rx_free_thresh;
>> +			} else {
>> +				PMD_RX_LOG(DEBUG, "RX bulk alloc failed "
>> +						  "port_id=%u queue_id=%u",
>> +					   rxq->port_id, rxq->queue_id);
>> +
>> +				rte_eth_devices[rxq->port_id].data->
>> +							rx_mbuf_alloc_failed++;
>> +				break;
>> +			}
>> +		}
>> +
>> +		nb_hold++;
>> +		rxe = &sw_ring[rx_id];
>> +		eop = staterr & IXGBE_RXDADV_STAT_EOP;
>> +
>> +		next_id = rx_id + 1;
>> +		if (next_id == rxq->nb_rx_desc)
>> +			next_id = 0;
>> +
>> +		/* Prefetch next mbuf while processing current one. */
>> +		rte_ixgbe_prefetch(sw_ring[next_id].mbuf);
>> +
>> +		/*
>> +		 * When next RX descriptor is on a cache-line boundary,
>> +		 * prefetch the next 4 RX descriptors and the next 4 pointers
>> +		 * to mbufs.
>> +		 */
>> +		if ((next_id & 0x3) == 0) {
>> +			rte_ixgbe_prefetch(&rx_ring[next_id]);
>> +			rte_ixgbe_prefetch(&sw_ring[next_id]);
>> +		}
>> +
>> +		rxm = rxe->mbuf;
>> +
>> +		if (!bulk_alloc) {
>> +			__le64 dma =
>> +			  rte_cpu_to_le_64(RTE_MBUF_DATA_DMA_ADDR_DEFAULT(nmb));
>> +			/*
>> +			 * Update RX descriptor with the physical address of the
>> +			 * new data buffer of the new allocated mbuf.
>> +			 */
>> +			rxe->mbuf = nmb;
>> +
>> +			rxm->data_off = RTE_PKTMBUF_HEADROOM;
>> +			rxdp->read.hdr_addr = dma;
>> +			rxdp->read.pkt_addr = dma;
>> +		} else
>> +			rxe->mbuf = NULL;
>> +
>> +		/*
>> +		 * Set data length & data buffer address of mbuf.
>> +		 */
>> +		data_len = rte_le_to_cpu_16(rxd.wb.upper.length);
>> +		rxm->data_len = data_len;
>> +
>> +		if (!eop) {
>> +			uint16_t nextp_id;
>> +			/*
>> +			 * Get next descriptor index:
>> +			 *  - For RSC it's in the NEXTP field.
>> +			 *  - For a scattered packet - it's just a following
>> +			 *    descriptor.
>> +			 */
>> +			if (ixgbe_rsc_count(&rxd))
>> +				nextp_id =
>> +					(staterr & IXGBE_RXDADV_NEXTP_MASK) >>
>> +						       IXGBE_RXDADV_NEXTP_SHIFT;
>> +			else
>> +				nextp_id = next_id;
>> +
>> +			next_rsc_entry = &sw_rsc_ring[nextp_id];
>> +			next_rxe = &sw_ring[nextp_id];
>> +			rte_ixgbe_prefetch(next_rxe);
>> +		}
>> +
>> +		rsc_entry = &sw_rsc_ring[rx_id];
>> +		first_seg = rsc_entry->fbuf;
>> +		rsc_entry->fbuf = NULL;
>> +
>> +		/*
>> +		 * If this is the first buffer of the received packet,
>> +		 * set the pointer to the first mbuf of the packet and
>> +		 * initialize its context.
>> +		 * Otherwise, update the total length and the number of segments
>> +		 * of the current scattered packet, and update the pointer to
>> +		 * the last mbuf of the current packet.
>> +		 */
>> +		if (first_seg == NULL) {
>> +			first_seg = rxm;
>> +			first_seg->pkt_len = data_len;
>> +			first_seg->nb_segs = 1;
>> +		} else {
>> +			first_seg->pkt_len += data_len;
>> +			first_seg->nb_segs++;
>> +		}
>> +
>> +		prev_id = rx_id;
>> +		rx_id = next_id;
>> +
>> +		/*
>> +		 * If this is not the last buffer of the received packet, update
>> +		 * the pointer to the first mbuf at the NEXTP entry in the
>> +		 * sw_rsc_ring and continue to parse the RX ring.
>> +		 */
>> +		if (!eop) {
>> +			rxm->next = next_rxe->mbuf;
>> +			next_rsc_entry->fbuf = first_seg;
>> +			goto next_desc;
>> +		}
>> +
>> +		/*
>> +		 * This is the last buffer of the received packet - return
>> +		 * the current cluster to the user.
>> +		 */
>> +		rxm->next = NULL;
>> +
>> +		/* Initialize the first mbuf of the returned packet */
>> +		ixgbe_fill_cluster_head_buf(first_seg, &rxd, rxq->port_id,
>> +					    staterr);
>> +
>> +		/* Prefetch data of first segment, if configured to do so. */
>> +		rte_packet_prefetch((char *)first_seg->buf_addr +
>> +			first_seg->data_off);
>> +
>> +		/*
>> +		 * Store the mbuf address into the next entry of the array
>> +		 * of returned packets.
>> +		 */
>> +		rx_pkts[nb_rx++] = first_seg;
>> +	}
>> +
>> +	/*
>> +	 * Record index of the next RX descriptor to probe.
>> +	 */
>> +	rxq->rx_tail = rx_id;
>> +
>> +	/*
>> +	 * If the number of free RX descriptors is greater than the RX free
>> +	 * threshold of the queue, advance the Receive Descriptor Tail (RDT)
>> +	 * register.
>> +	 * Update the RDT with the value of the last processed RX descriptor
>> +	 * minus 1, to guarantee that the RDT register is never equal to the
>> +	 * RDH register, which creates a "full" ring situtation from the
>> +	 * hardware point of view...
>> +	 */
>> +	if (!bulk_alloc && nb_hold > rxq->rx_free_thresh) {
>> +		PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_tail=%u "
>> +			   "nb_hold=%u nb_rx=%u",
>> +			   rxq->port_id, rxq->queue_id, rx_id, nb_hold, nb_rx);
>> +
>> +		rte_wmb();
>> +		IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr, prev_id);
>> +		nb_hold = 0;
>> +	}
>> +
>> +	rxq->nb_rx_hold = nb_hold;
>> +	return nb_rx;
>> +}
>> +
>> +uint16_t
>> +ixgbe_recv_pkts_lro_single_alloc(void *rx_queue, struct rte_mbuf **rx_pkts,
>> +				 uint16_t nb_pkts)
>> +{
>> +	return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, false);
>> +}
>> +
>> +uint16_t
>> +ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue, struct rte_mbuf **rx_pkts,
>> +			       uint16_t nb_pkts)
>> +{
>> +	return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, true);
>> +}
>> +
>>   uint16_t
>>   ixgbe_recv_scattered_pkts(void *rx_queue, struct rte_mbuf **rx_pkts,
>>   			  uint16_t nb_pkts)
>> @@ -2005,6 +2295,31 @@ ixgbe_dev_tx_queue_setup(struct rte_eth_dev *dev,
>>   	return (0);
>>   }
>>
>> +/**
>> + * ixgbe_free_rsc_cluster - free the not-yet-completed RSC cluster
>> + *
>> + * The "next" pointer of the last segment of (not-yet-completed) RSC clusters
>> + * in the sw_rsc_ring is not set to NULL but rather points to the next
>> + * mbuf of this RSC aggregation (that has not been completed yet and still
>> + * resides on the HW ring). So, instead of calling for rte_pktmbuf_free() we
>> + * will just free first "nb_segs" segments of the cluster explicitly by calling
>> + * an rte_pktmbuf_free_seg().
>> + *
>> + * @m RSC cluster head
>> + */
>> +static void
>> +ixgbe_free_rsc_cluster(struct rte_mbuf *m)
>> +{
>> +	uint8_t i, nb_segs = m->nb_segs;
>> +	struct rte_mbuf *next_seg;
>> +
>> +	for (i = 0; i < nb_segs; i++) {
>> +		next_seg = m->next;
>> +		rte_pktmbuf_free_seg(m);
>> +		m = next_seg;
>> +	}
>> +}
>> +
>>   static void
>>   ixgbe_rx_queue_release_mbufs(struct ixgbe_rx_queue *rxq)
>>   {
>> @@ -2028,6 +2343,13 @@ ixgbe_rx_queue_release_mbufs(struct ixgbe_rx_queue *rxq)
>>   		}
>>   #endif
>>   	}
>> +
>> +	if (rxq->sw_rsc_ring)
>> +		for (i = 0; i < rxq->nb_rx_desc; i++)
>> +			if (rxq->sw_rsc_ring[i].fbuf) {
>> +				ixgbe_free_rsc_cluster(rxq->sw_rsc_ring[i].fbuf);
>> +				rxq->sw_rsc_ring[i].fbuf = NULL;
>> +			}
>>   }
>>
>>   static void
>> @@ -2036,6 +2358,7 @@ ixgbe_rx_queue_release(struct ixgbe_rx_queue *rxq)
>>   	if (rxq != NULL) {
>>   		ixgbe_rx_queue_release_mbufs(rxq);
>>   		rte_free(rxq->sw_ring);
>> +		rte_free(rxq->sw_rsc_ring);
>>   		rte_free(rxq);
>>   	}
>>   }
>> @@ -2158,6 +2481,7 @@ ixgbe_reset_rx_queue(struct ixgbe_hw *hw, struct ixgbe_rx_queue *rxq)
>>   	rxq->nb_rx_hold = 0;
>>   	rxq->pkt_first_seg = NULL;
>>   	rxq->pkt_last_seg = NULL;
>> +	rxq->rsc_en = 0;
>>   }
>>
>>   int
>> @@ -2172,6 +2496,14 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev *dev,
>>   	struct ixgbe_rx_queue *rxq;
>>   	struct ixgbe_hw     *hw;
>>   	uint16_t len;
>> +	struct rte_eth_dev_info dev_info = { 0 };
>> +	struct rte_eth_rxmode *dev_rx_mode = &dev->data->dev_conf.rxmode;
>> +	bool rsc_requested = false;
>> +
>> +	dev->dev_ops->dev_infos_get(dev, &dev_info);
>> +	if ((dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO) &&
>> +	    dev_rx_mode->enable_lro)
>> +		rsc_requested = true;
>>
>>   	PMD_INIT_FUNC_TRACE();
>>   	hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>> @@ -2277,12 +2609,27 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev *dev,
>>   	rxq->sw_ring = rte_zmalloc_socket("rxq->sw_ring",
>>   					  sizeof(struct ixgbe_rx_entry) * len,
>>   					  RTE_CACHE_LINE_SIZE, socket_id);
>> -	if (rxq->sw_ring == NULL) {
>> +	if (!rxq->sw_ring) {
>>   		ixgbe_rx_queue_release(rxq);
>>   		return (-ENOMEM);
>>   	}
>> -	PMD_INIT_LOG(DEBUG, "sw_ring=%p hw_ring=%p dma_addr=0x%"PRIx64,
>> -		     rxq->sw_ring, rxq->rx_ring, rxq->rx_ring_phys_addr);
>> +
>> +	if (rsc_requested) {
>> +		rxq->sw_rsc_ring =
>> +			rte_zmalloc_socket("rxq->sw_rsc_ring",
>> +					   sizeof(struct ixgbe_rsc_entry) * len,
>> +					   RTE_CACHE_LINE_SIZE, socket_id);
>> +		if (!rxq->sw_rsc_ring) {
>> +			ixgbe_rx_queue_release(rxq);
>> +			return (-ENOMEM);
>> +		}
>> +	} else
>> +		rxq->sw_rsc_ring = NULL;
>> +
>> +	PMD_INIT_LOG(DEBUG, "sw_ring=%p sw_rsc_ring=%p hw_ring=%p "
>> +			    "dma_addr=0x%"PRIx64,
>> +		     rxq->sw_ring, rxq->sw_rsc_ring, rxq->rx_ring,
>> +		     rxq->rx_ring_phys_addr);
>>
>>   	if (!rte_is_power_of_2(nb_desc)) {
>>   		PMD_INIT_LOG(DEBUG, "queue[%d] doesn't meet Vector Rx "
>> @@ -3527,6 +3874,91 @@ ixgbe_dev_mq_tx_configure(struct rte_eth_dev *dev)
>>   	return 0;
>>   }
>>
>> +/**
>> + * ixgbe_get_rscctl_maxdesc - Calculate the RSCCTL[n].MAXDESC for PF
>> + *
>> + * Return the RSCCTL[n].MAXDESC for 82599 and x540 PF devices according to the
>> + * spec rev. 3.0 chapter 8.2.3.8.13.
>> + *
>> + * @pool Memory pool of the Rx queue
>> + */
>> +static inline uint32_t
>> +ixgbe_get_rscctl_maxdesc(struct rte_mempool *pool)
>> +{
>> +	struct rte_pktmbuf_pool_private *mp_priv = rte_mempool_get_priv(pool);
>> +
>> +	/* MAXDESC * SRRCTL.BSIZEPKT must not exceed 64 KB minus one */
>> +	uint16_t maxdesc =
>> +		IPV4_MAX_PKT_LEN /
>> +			(mp_priv->mbuf_data_room_size - RTE_PKTMBUF_HEADROOM);
>> +
>> +	if (maxdesc >= 16)
>> +		return IXGBE_RSCCTL_MAXDESC_16;
>> +	else if (maxdesc >= 8)
>> +		return IXGBE_RSCCTL_MAXDESC_8;
>> +	else if (maxdesc >= 4)
>> +		return IXGBE_RSCCTL_MAXDESC_4;
>> +	else
>> +		return IXGBE_RSCCTL_MAXDESC_1;
>> +}
>> +
>> +/**
>> + * ixgbe_set_ivar - Setup the correct IVAR register for a particular MSIX
>> + * interrupt
>> + *
>> + * (Taken from FreeBSD tree)
>> + * (yes this is all very magic and confusing :)
>> + *
>> + * @dev port handle
>> + * @entry the register array entry
>> + * @vector the MSIX vector for this queue
>> + * @type RX/TX/MISC
>> + */
>> +static void
>> +ixgbe_set_ivar(struct rte_eth_dev *dev, u8 entry, u8 vector, s8 type)
>> +{
>> +	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>> +	u32 ivar, index;
>> +
>> +	vector |= IXGBE_IVAR_ALLOC_VAL;
>> +
>> +	switch (hw->mac.type) {
>> +
>> +	case ixgbe_mac_82598EB:
>> +		if (type == -1)
>> +			entry = IXGBE_IVAR_OTHER_CAUSES_INDEX;
>> +		else
>> +			entry += (type * 64);
>> +		index = (entry >> 2) & 0x1F;
>> +		ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(index));
>> +		ivar &= ~(0xFF << (8 * (entry & 0x3)));
>> +		ivar |= (vector << (8 * (entry & 0x3)));
>> +		IXGBE_WRITE_REG(hw, IXGBE_IVAR(index), ivar);
>> +		break;
>> +
>> +	case ixgbe_mac_82599EB:
>> +	case ixgbe_mac_X540:
>> +		if (type == -1) { /* MISC IVAR */
>> +			index = (entry & 1) * 8;
>> +			ivar = IXGBE_READ_REG(hw, IXGBE_IVAR_MISC);
>> +			ivar &= ~(0xFF << index);
>> +			ivar |= (vector << index);
>> +			IXGBE_WRITE_REG(hw, IXGBE_IVAR_MISC, ivar);
>> +		} else {	/* RX/TX IVARS */
>> +			index = (16 * (entry & 1)) + (8 * type);
>> +			ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(entry >> 1));
>> +			ivar &= ~(0xFF << index);
>> +			ivar |= (vector << index);
>> +			IXGBE_WRITE_REG(hw, IXGBE_IVAR(entry >> 1), ivar);
>> +		}
>> +
>> +		break;
>> +
>> +	default:
>> +		break;
>> +	}
>> +}
>> +
>>   void ixgbe_set_rx_function(struct rte_eth_dev *dev)
>>   {
>>   	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>> @@ -3545,7 +3977,24 @@ void ixgbe_set_rx_function(struct rte_eth_dev *dev)
>>   		hw->rx_vec_allowed = false;
>>   	}
>>
>> -	if (dev->data->scattered_rx) {
>> +	/*
>> +	 * Initialize the appropriate LRO callback.
>> +	 *
>> +	 * If all queues satisfy the bulk allocation preconditions
>> +	 * (hw->rx_bulk_alloc_allowed is TRUE) then we may use bulk allocation.
>> +	 * Otherwise use a single allocation version.
>> +	 */
>> +	if (dev->data->lro) {
>> +		if (hw->rx_bulk_alloc_allowed) {
>> +			PMD_INIT_LOG(INFO, "LRO is requested. Using a bulk "
>> +					   "allocation version");
>> +			dev->rx_pkt_burst = ixgbe_recv_pkts_lro_bulk_alloc;
>> +		} else {
>> +			PMD_INIT_LOG(INFO, "LRO is requested. Using a single "
>> +					   "allocation version");
>> +			dev->rx_pkt_burst = ixgbe_recv_pkts_lro_single_alloc;
>> +		}
>> +	} else if (dev->data->scattered_rx) {
>>   		/*
>>   		 * Set the non-LRO scattered callback: there are Vector and
>>   		 * single allocation versions.
>> @@ -3595,6 +4044,149 @@ void ixgbe_set_rx_function(struct rte_eth_dev *dev)
>>   	}
>>   }
>>
>> +/**
>> + * ixgbe_set_rsc - configure RSC related port HW registers
>> + *
>> + * Configures the port's RSC related registers according to the 4.6.7.2 chapter
>> + * of 82599 Spec (x540 configuration is virtually the same).
>> + *
>> + * @dev port handle
>> + *
>> + * Returns 0 in case of success or a non-zero error code
>> + */
>> +static int
>> +ixgbe_set_rsc(struct rte_eth_dev *dev)
>> +{
>> +	struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
>> +	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>> +	struct rte_eth_dev_info dev_info = { 0 };
>> +	bool rsc_capable = false;
>> +	uint16_t i;
>> +	uint32_t rdrxctl;
>> +
>> +	/* Sanity check */
>> +	dev->dev_ops->dev_infos_get(dev, &dev_info);
>> +	if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO)
>> +		rsc_capable = true;
>> +
>> +	if (!rsc_capable && rx_conf->enable_lro) {
>> +		PMD_INIT_LOG(CRIT, "LRO is requested on HW that doesn't "
>> +				   "support it");
>> +		return -EINVAL;
>> +	}
>> +
>> +	/* RSC global configuration (chapter 4.6.7.2.1 of 82599 Spec) */
>> +
>> +	if (!rx_conf->hw_strip_crc && rx_conf->enable_lro) {
>> +		/*
>> +		 * According to chapter of 4.6.7.2.1 of the Spec Rev.
>> +		 * 3.0 RSC configuration requires HW CRC stripping being
>> +		 * enabled. If user requested both HW CRC stripping off
>> +		 * and RSC on - return an error.
>> +		 */
>> +		PMD_INIT_LOG(CRIT, "LRO can't be enabled when HW CRC "
>> +				    "is disabled");
>> +		return -EINVAL;
>> +	}
>> +
>> +	/* RFCTL configuration  */
>> +	if (rsc_capable) {
>> +		uint32_t rfctl = IXGBE_READ_REG(hw, IXGBE_RFCTL);
>> +		if (rx_conf->enable_lro)
>> +			/*
>> +			 * Since NFS packets coalescing is not supported - clear
>> +			 * RFCTL.NFSW_DIS and RFCTL.NFSR_DIS when RSC is
>> +			 * enabled.
>> +			 */
>> +			rfctl &= ~(IXGBE_RFCTL_RSC_DIS | IXGBE_RFCTL_NFSW_DIS |
>> +				   IXGBE_RFCTL_NFSR_DIS);
>> +		else
>> +			rfctl |= IXGBE_RFCTL_RSC_DIS;
>> +
>> +		IXGBE_WRITE_REG(hw, IXGBE_RFCTL, rfctl);
>> +	}
>> +
>> +	/* If LRO hasn't been requested - we are done here. */
>> +	if (!rx_conf->enable_lro)
>> +		return 0;
>> +
>> +	/* Set RDRXCTL.RSCACKC bit */
>> +	rdrxctl = IXGBE_READ_REG(hw, IXGBE_RDRXCTL);
>> +	rdrxctl |= IXGBE_RDRXCTL_RSCACKC;
>> +	IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
>> +
>> +	/* Per-queue RSC configuration (chapter 4.6.7.2.2 of 82599 Spec) */
>> +	for (i = 0; i < dev->data->nb_rx_queues; i++) {
>> +		struct ixgbe_rx_queue *rxq = dev->data->rx_queues[i];
>> +		uint32_t srrctl =
>> +			IXGBE_READ_REG(hw, IXGBE_SRRCTL(rxq->reg_idx));
>> +		uint32_t rscctl =
>> +			IXGBE_READ_REG(hw, IXGBE_RSCCTL(rxq->reg_idx));
>> +		uint32_t psrtype =
>> +			IXGBE_READ_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx));
>> +		uint32_t eitr =
>> +			IXGBE_READ_REG(hw, IXGBE_EITR(rxq->reg_idx));
>> +
>> +		/*
>> +		 * ixgbe PMD doesn't support header-split at the moment.
>> +		 *
>> +		 * Following the 4.6.7.2.1 chapter of the 82599/x540
>> +		 * Spec if RSC is enabled the SRRCTL[n].BSIZEHEADER
>> +		 * should be configured even if header split is not
>> +		 * enabled. We will configure it 128 bytes following the
>> +		 * recommendation in the spec.
>> +		 */
>> +		srrctl &= ~IXGBE_SRRCTL_BSIZEHDR_MASK;
>> +		srrctl |= (128 << IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT) &
>> +					    IXGBE_SRRCTL_BSIZEHDR_MASK;
>> +
>> +		/*
>> +		 * TODO: Consider setting the Receive Descriptor Minimum
>> +		 * Threshold Size for an RSC case. This is not an obviously
>> +		 * beneficiary option but the one worth considering...
>> +		 */
>> +
>> +		rscctl |= IXGBE_RSCCTL_RSCEN;
>> +		rscctl |= ixgbe_get_rscctl_maxdesc(rxq->mb_pool);
>> +		psrtype |= IXGBE_PSRTYPE_TCPHDR;
>> +
>> +		/*
>> +		 * RSC: Set ITR interval corresponding to 2K ints/s.
>> +		 *
>> +		 * Full-sized RSC aggregations for a 10Gb/s link will
>> +		 * arrive at about 20K aggregation/s rate.
>> +		 *
>> +		 * 2K inst/s rate will make only 10% of the
>> +		 * aggregations to be closed due to the interrupt timer
>> +		 * expiration for a streaming at wire-speed case.
>> +		 *
>> +		 * For a sparse streaming case this setting will yield
>> +		 * at most 500us latency for a single RSC aggregation.
>> +		 */
>> +		eitr &= ~IXGBE_EITR_ITR_INT_MASK;
>> +		eitr |= IXGBE_EITR_INTERVAL_US(500) | IXGBE_EITR_CNT_WDIS;
>> +
>> +		IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
>> +		IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(rxq->reg_idx), rscctl);
>> +		IXGBE_WRITE_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx), psrtype);
>> +		IXGBE_WRITE_REG(hw, IXGBE_EITR(rxq->reg_idx), eitr);
>> +
>> +		/*
>> +		 * RSC requires the mapping of the queue to the
>> +		 * interrupt vector.
>> +		 */
>> +		ixgbe_set_ivar(dev, rxq->reg_idx, i, 0);
>> +
>> +		rxq->rsc_en = 1;
>> +	}
>> +
>> +	dev->data->lro = 1;
>> +
>> +	PMD_INIT_LOG(INFO, "enabling LRO mode");
>> +
>> +	return 0;
>> +}
>> +
>>   /*
>>    * Initializes Receive Unit.
>>    */
>> @@ -3615,6 +4207,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>   	uint16_t buf_size;
>>   	uint16_t i;
>>   	struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
>> +	int rc;
>>
>>   	PMD_INIT_FUNC_TRACE();
>>   	hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
>> @@ -3724,6 +4317,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>   				       RTE_PKTMBUF_HEADROOM);
>>   		srrctl |= ((buf_size >> IXGBE_SRRCTL_BSIZEPKT_SHIFT) &
>>   			   IXGBE_SRRCTL_BSIZEPKT_MASK);
>> +
>>   		IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
>>
>>   		buf_size = (uint16_t) ((srrctl & IXGBE_SRRCTL_BSIZEPKT_MASK) <<
>> @@ -3738,8 +4332,6 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>   	if (rx_conf->enable_scatter)
>>   		dev->data->scattered_rx = 1;
>>
>> -	ixgbe_set_rx_function(dev);
>> -
>>   	/*
>>   	 * Device configured with multiple RX queues.
>>   	 */
>> @@ -3770,6 +4362,12 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>   		IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
>>   	}
>>
>> +	rc = ixgbe_set_rsc(dev);
>> +	if (rc)
>> +		return rc;
>> +
>> +	ixgbe_set_rx_function(dev);
>> +
>>   	return 0;
>>   }
>>
>> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
>> index 3937cf6..120bbbd 100644
>> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
>> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
>> @@ -79,6 +79,10 @@ struct ixgbe_rx_entry {
>>   	struct rte_mbuf *mbuf; /**< mbuf associated with RX descriptor. */
>>   };
>>
>> +struct ixgbe_rsc_entry {
>> +	struct rte_mbuf *fbuf; /**< First segment of the fragmented packet. */
>> +};
>> +
>>   /**
>>    * Structure associated with each descriptor of the TX ring of a TX queue.
>>    */
>> @@ -105,6 +109,7 @@ struct ixgbe_rx_queue {
>>   	volatile uint32_t   *rdt_reg_addr; /**< RDT register address. */
>>   	volatile uint32_t   *rdh_reg_addr; /**< RDH register address. */
>>   	struct ixgbe_rx_entry *sw_ring; /**< address of RX software ring. */
>> +	struct ixgbe_rsc_entry *sw_rsc_ring; /**< address of RSC software ring. */
>>   	struct rte_mbuf *pkt_first_seg; /**< First segment of current packet. */
>>   	struct rte_mbuf *pkt_last_seg; /**< Last segment of current packet. */
>>   	uint64_t            mbuf_initializer; /**< value to init mbufs */
>> @@ -126,6 +131,7 @@ struct ixgbe_rx_queue {
>>   	uint8_t             port_id;  /**< Device port identifier. */
>>   	uint8_t             crc_len;  /**< 0 if CRC stripped, 4 otherwise. */
>>   	uint8_t             drop_en;  /**< If not 0, set SRRCTL.Drop_En. */
>> +	uint8_t             rsc_en;   /**< If not 0, RSC is enabled. */
>>   	uint8_t             rx_deferred_start; /**< not in global dev start. */
>>   #ifdef RTE_LIBRTE_IXGBE_RX_ALLOW_BULK_ALLOC
>>   	/** need to alloc dummy mbuf, for wraparound when scanning hw ring */
>> --
>> 2.1.0

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
  2015-03-18 17:52 ` [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support Vlad Zolotarov
@ 2015-03-30 14:18   ` Ananyev, Konstantin
  2015-03-30 15:37     ` Vlad Zolotarov
  0 siblings, 1 reply; 6+ messages in thread
From: Ananyev, Konstantin @ 2015-03-30 14:18 UTC (permalink / raw)
  To: Vlad Zolotarov, dev

Hi Vlad,

> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Vlad Zolotarov
> Sent: Wednesday, March 18, 2015 5:52 PM
> To: dev@dpdk.org
> Subject: [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support
> 
>     - Only x540 and 82599 devices support LRO.
>     - Add the appropriate HW configuration.
>     - Add RSC aware rx_pkt_burst() handlers:
>        - Implemented bulk allocation and non-bulk allocation versions.
>        - Add LRO-specific fields to rte_eth_rxmode, to rte_eth_dev_data
>          and to ixgbe_rx_queue.
>        - Use the appropriate handler when LRO is requested.
> 
> Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
> ---
> New in v8:
>    - Took the RSC configuration code from ixgbe_dev_rx_init() into a separate
>      function - ixgbe_set_rsc().
>    - Added some missing macros for HW configuration.
>    - Styling adjustments:
>       - Functions names.
>       - Functions descriptions.
>    - Reworked the ixgbe_free_rsc_cluster() code to make it more readable.
>    - Kill the HEADER_SPLIT flow in ixgbe_set_rsc() since it's not supported by
>      ixgbe PMD.
> 
> New in v7:
>    - Free not-yet-completed RSC aggregations in rte_eth_dev_stop() flow.
>    - Reset the sw_ring[].mbuf entry in a bulk allocation case.
>      This is needed for ixgbe_rx_queue_release_mbufs().
>    - _recv_pkts_lro(): added the missing memory barrier before RDT update in a
>      non-bulk allocation case.
>    - Don't allow RSC when device is configured in an SR-IOV mode.
> 
> New in v5:
>    - Put the RTE_ETHDEV_HAS_LRO_SUPPORT definition at the beginning of rte_ethdev.h.
>    - Removed the "TODO: Remove me" comment near RTE_ETHDEV_HAS_LRO_SUPPORT.
> 
> New in v4:
>    - Define RTE_ETHDEV_HAS_LRO_SUPPORT in rte_ethdev.h instead of
>      RTE_ETHDEV_LRO_SUPPORT defined in config/common_linuxapp.
> 
> New in v2:
>    - Removed rte_eth_dev_data.lro_bulk_alloc.
>    - Fixed a few styling and spelling issues.
> ---
>  lib/librte_ether/rte_ethdev.h           |   9 +-
>  lib/librte_net/rte_ip.h                 |   3 +
>  lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h |   6 +
>  lib/librte_pmd_ixgbe/ixgbe_ethdev.c     |  11 +
>  lib/librte_pmd_ixgbe/ixgbe_ethdev.h     |   5 +
>  lib/librte_pmd_ixgbe/ixgbe_rxtx.c       | 610 +++++++++++++++++++++++++++++++-
>  lib/librte_pmd_ixgbe/ixgbe_rxtx.h       |   6 +
>  7 files changed, 642 insertions(+), 8 deletions(-)
> 
> diff --git a/lib/librte_ether/rte_ethdev.h b/lib/librte_ether/rte_ethdev.h
> index 21aa359..61dc49a 100644
> --- a/lib/librte_ether/rte_ethdev.h
> +++ b/lib/librte_ether/rte_ethdev.h
> @@ -172,6 +172,9 @@ extern "C" {
> 
>  #include <stdint.h>
> 
> +/* Use this macro to check if LRO API is supported */
> +#define RTE_ETHDEV_HAS_LRO_SUPPORT
> +
>  #include <rte_log.h>
>  #include <rte_interrupts.h>
>  #include <rte_pci.h>
> @@ -320,14 +323,15 @@ struct rte_eth_rxmode {
>  	enum rte_eth_rx_mq_mode mq_mode;
>  	uint32_t max_rx_pkt_len;  /**< Only used if jumbo_frame enabled. */
>  	uint16_t split_hdr_size;  /**< hdr buf size (header_split enabled).*/
> -	uint8_t header_split : 1, /**< Header Split enable. */
> +	uint16_t header_split : 1, /**< Header Split enable. */
>  		hw_ip_checksum   : 1, /**< IP/UDP/TCP checksum offload enable. */
>  		hw_vlan_filter   : 1, /**< VLAN filter enable. */
>  		hw_vlan_strip    : 1, /**< VLAN strip enable. */
>  		hw_vlan_extend   : 1, /**< Extended VLAN enable. */
>  		jumbo_frame      : 1, /**< Jumbo Frame Receipt enable. */
>  		hw_strip_crc     : 1, /**< Enable CRC stripping by hardware. */
> -		enable_scatter   : 1; /**< Enable scatter packets rx handler */
> +		enable_scatter   : 1, /**< Enable scatter packets rx handler */
> +		enable_lro       : 1; /**< Enable LRO */
>  };
> 
>  /**
> @@ -1515,6 +1519,7 @@ struct rte_eth_dev_data {
>  	uint8_t port_id;           /**< Device [external] port identifier. */
>  	uint8_t promiscuous   : 1, /**< RX promiscuous mode ON(1) / OFF(0). */
>  		scattered_rx : 1,  /**< RX of scattered packets is ON(1) / OFF(0) */
> +		lro          : 1,  /**< RX LRO is ON(1) / OFF(0) */
>  		all_multicast : 1, /**< RX all multicast mode ON(1) / OFF(0). */
>  		dev_started : 1;   /**< Device state: STARTED(1) / STOPPED(0). */
>  };
> diff --git a/lib/librte_net/rte_ip.h b/lib/librte_net/rte_ip.h
> index 64935d9..74c9ced 100644
> --- a/lib/librte_net/rte_ip.h
> +++ b/lib/librte_net/rte_ip.h
> @@ -110,6 +110,9 @@ struct ipv4_hdr {
>  					   (((c) & 0xff) << 8)  | \
>  					   ((d) & 0xff))
> 
> +/** Maximal IPv4 packet length (including a header) */
> +#define IPV4_MAX_PKT_LEN        65535
> +
>  /** Internet header length mask for version_ihl field */
>  #define IPV4_HDR_IHL_MASK	(0x0f)
>  /**
> diff --git a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
> index 9a66370..4998627 100644
> --- a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
> +++ b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
> @@ -234,8 +234,14 @@ struct ixgbe_thermal_sensor_data {
>  #define IXGBE_EITR(_i)		(((_i) <= 23) ? (0x00820 + ((_i) * 4)) : \
>  				 (0x012300 + (((_i) - 24) * 4)))
>  #define IXGBE_EITR_ITR_INT_MASK	0x00000FF8
> +#define IXGBE_EITR_ITR_INT_SHIFT 3
>  #define IXGBE_EITR_LLI_MOD	0x00008000
>  #define IXGBE_EITR_CNT_WDIS	0x80000000
> +/* EITR Inteval is in 2048ns uinits for 1G and 10G link */

> +#define IXGBE_EITR_INTERVAL_UNIT_NS	2048

Why is that? Why not just 2us as 82599 spec says?
And then:
+#define IXGBE_EITR_INTERVAL_US(us) (((us) / IXGBE_EITR_INTERVAL_UNIT_US << IXGBE_EITR_ITR_INT_SHIFT) & IXGBE_EITR_ITR_INT_MASK)
?

> +#define IXGBE_EITR_INTERVAL_US(us)	\
> +   (((us) * 1000 / IXGBE_EITR_INTERVAL_UNIT_NS << IXGBE_EITR_ITR_INT_SHIFT) & \
> +		IXGBE_EITR_ITR_INT_MASK)


Unfortunately we are not supposed to change files under ixgbe subfirectory (except ixgbe_osdep.*).
These files comes from ixgbe shared code and we treat them as read-only.
You need to move these new macros you added into ixgbe_ethedev.h.

All other things look good to me.
Konstantin

>  #define IXGBE_IVAR(_i)		(0x00900 + ((_i) * 4)) /* 24 at 0x900-0x960 */
>  #define IXGBE_IVAR_MISC		0x00A00 /* misc MSI-X interrupt causes */
>  #define IXGBE_EITRSEL		0x00894
> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
> index 92d75db..923692e 100644
> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
> @@ -1645,6 +1645,7 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
> 
>  	/* Clear stored conf */
>  	dev->data->scattered_rx = 0;
> +	dev->data->lro = 0;
> 
>  	/* Clear recorded link status */
>  	memset(&link, 0, sizeof(link));
> @@ -2013,6 +2014,16 @@ ixgbe_dev_info_get(struct rte_eth_dev *dev, struct rte_eth_dev_info *dev_info)
>  		DEV_RX_OFFLOAD_IPV4_CKSUM |
>  		DEV_RX_OFFLOAD_UDP_CKSUM  |
>  		DEV_RX_OFFLOAD_TCP_CKSUM;
> +
> +	/*
> +	 * RSC is only supported by 82599 and x540 PF devices in a non-SR-IOV
> +	 * mode.
> +	 */
> +	if ((hw->mac.type == ixgbe_mac_82599EB ||
> +	     hw->mac.type == ixgbe_mac_X540) &&
> +	    !RTE_ETH_DEV_SRIOV(dev).active)
> +		dev_info->rx_offload_capa |= DEV_RX_OFFLOAD_TCP_LRO;
> +
>  	dev_info->tx_offload_capa =
>  		DEV_TX_OFFLOAD_VLAN_INSERT |
>  		DEV_TX_OFFLOAD_IPV4_CKSUM  |
> diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
> index ffe3471..7050340 100644
> --- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
> +++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
> @@ -344,6 +344,11 @@ uint16_t ixgbe_recv_pkts(void *rx_queue, struct rte_mbuf **rx_pkts,
>  uint16_t ixgbe_recv_scattered_pkts(void *rx_queue,
>  		struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
> 
> +uint16_t ixgbe_recv_pkts_lro_single_alloc(void *rx_queue,
> +		struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
> +uint16_t ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue,
> +		struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
> +
>  uint16_t ixgbe_xmit_pkts(void *tx_queue, struct rte_mbuf **tx_pkts,
>  		uint16_t nb_pkts);
> 
> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
> index a08ae6a..daa4c45 100644
> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
> @@ -70,6 +70,7 @@
>  #include <rte_sctp.h>
>  #include <rte_string_fns.h>
>  #include <rte_errno.h>
> +#include <rte_ip.h>
> 
>  #include "ixgbe_logs.h"
>  #include "ixgbe/ixgbe_api.h"
> @@ -1422,6 +1423,295 @@ ixgbe_fill_cluster_head_buf(
>  	}
>  }
> 
> +/**
> + * ixgbe_recv_pkts_lro - receive handler for and LRO case.
> + *
> + * @rx_queue Rx queue handle
> + * @rx_pkts table of received packets
> + * @nb_pkts size of rx_pkts table
> + * @bulk_alloc if TRUE bulk allocation is used for a HW ring refilling
> + *
> + * Handles the Rx HW ring completions when RSC feature is configured. Uses an
> + * additional ring of ixgbe_rsc_entry's that will hold the relevant RSC info.
> + *
> + * We use the same logic as in Lunux and in FreeBSD ixgbe drivers:
> + * 1) When non-EOP RSC completion arrives:
> + *    a) Update the HEAD of the current RSC aggregation cluster with the new
> + *       segment's data length.
> + *    b) Set the "next" pointer of the current segment to point to the segment
> + *       at the NEXTP index.
> + *    c) Pass the HEAD of RSC aggregation cluster on to the next NEXTP entry
> + *       in the sw_rsc_ring.
> + * 2) When EOP arrives we just update the cluster's total length and offload
> + *    flags and deliver the cluster up to the upper layers. In our case - put it
> + *    in the rx_pkts table.
> + *
> + * Returns the number of received packets/clusters (according to the "bulk
> + * receive" interface).
> + */
> +static inline uint16_t
> +ixgbe_recv_pkts_lro(void *rx_queue, struct rte_mbuf **rx_pkts, uint16_t nb_pkts,
> +		    bool bulk_alloc)
> +{
> +	struct ixgbe_rx_queue *rxq = rx_queue;
> +	volatile union ixgbe_adv_rx_desc *rx_ring = rxq->rx_ring;
> +	struct ixgbe_rx_entry *sw_ring = rxq->sw_ring;
> +	struct ixgbe_rsc_entry *sw_rsc_ring = rxq->sw_rsc_ring;
> +	uint16_t rx_id = rxq->rx_tail;
> +	uint16_t nb_rx = 0;
> +	uint16_t nb_hold = rxq->nb_rx_hold;
> +	uint16_t prev_id = rxq->rx_tail;
> +
> +	while (nb_rx < nb_pkts) {
> +		bool eop;
> +		struct ixgbe_rx_entry *rxe;
> +		struct ixgbe_rsc_entry *rsc_entry;
> +		struct ixgbe_rsc_entry *next_rsc_entry;
> +		struct ixgbe_rx_entry *next_rxe;
> +		struct rte_mbuf *first_seg;
> +		struct rte_mbuf *rxm;
> +		struct rte_mbuf *nmb;
> +		union ixgbe_adv_rx_desc rxd;
> +		uint16_t data_len;
> +		uint16_t next_id;
> +		volatile union ixgbe_adv_rx_desc *rxdp;
> +		uint32_t staterr;
> +
> +next_desc:
> +		/*
> +		 * The code in this whole file uses the volatile pointer to
> +		 * ensure the read ordering of the status and the rest of the
> +		 * descriptor fields (on the compiler level only!!!). This is so
> +		 * UGLY - why not to just use the compiler barrier instead? DPDK
> +		 * even has the rte_compiler_barrier() for that.
> +		 *
> +		 * But most importantly this is just wrong because this doesn't
> +		 * ensure memory ordering in a general case at all. For
> +		 * instance, DPDK is supposed to work on Power CPUs where
> +		 * compiler barrier may just not be enough!
> +		 *
> +		 * I tried to write only this function properly to have a
> +		 * starting point (as a part of an LRO/RSC series) but the
> +		 * compiler cursed at me when I tried to cast away the
> +		 * "volatile" from rx_ring (yes, it's volatile too!!!). So, I'm
> +		 * keeping it the way it is for now.
> +		 *
> +		 * The code in this file is broken in so many other places and
> +		 * will just not work on a big endian CPU anyway therefore the
> +		 * lines below will have to be revisited together with the rest
> +		 * of the ixgbe PMD.
> +		 *
> +		 * TODO:
> +		 *    - Get rid of "volatile" crap and let the compiler do its
> +		 *      job.
> +		 *    - Use the proper memory barrier (rte_rmb()) to ensure the
> +		 *      memory ordering below.
> +		 */
> +		rxdp = &rx_ring[rx_id];
> +		staterr = rte_le_to_cpu_32(rxdp->wb.upper.status_error);
> +
> +		if (!(staterr & IXGBE_RXDADV_STAT_DD))
> +			break;
> +
> +		rxd = *rxdp;
> +
> +		PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_id=%u "
> +				  "staterr=0x%x data_len=%u",
> +			   rxq->port_id, rxq->queue_id, rx_id, staterr,
> +			   rte_le_to_cpu_16(rxd.wb.upper.length));
> +
> +		if (!bulk_alloc) {
> +			nmb = rte_rxmbuf_alloc(rxq->mb_pool);
> +			if (nmb == NULL) {
> +				PMD_RX_LOG(DEBUG, "RX mbuf alloc failed "
> +						  "port_id=%u queue_id=%u",
> +					   rxq->port_id, rxq->queue_id);
> +
> +				rte_eth_devices[rxq->port_id].data->
> +							rx_mbuf_alloc_failed++;
> +				break;
> +			}
> +		} else if (nb_hold > rxq->rx_free_thresh) {
> +			uint16_t next_rdt = rxq->rx_free_trigger;
> +
> +			if (!ixgbe_rx_alloc_bufs(rxq, false)) {
> +				rte_wmb();
> +				IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr,
> +						    next_rdt);
> +				nb_hold -= rxq->rx_free_thresh;
> +			} else {
> +				PMD_RX_LOG(DEBUG, "RX bulk alloc failed "
> +						  "port_id=%u queue_id=%u",
> +					   rxq->port_id, rxq->queue_id);
> +
> +				rte_eth_devices[rxq->port_id].data->
> +							rx_mbuf_alloc_failed++;
> +				break;
> +			}
> +		}
> +
> +		nb_hold++;
> +		rxe = &sw_ring[rx_id];
> +		eop = staterr & IXGBE_RXDADV_STAT_EOP;
> +
> +		next_id = rx_id + 1;
> +		if (next_id == rxq->nb_rx_desc)
> +			next_id = 0;
> +
> +		/* Prefetch next mbuf while processing current one. */
> +		rte_ixgbe_prefetch(sw_ring[next_id].mbuf);
> +
> +		/*
> +		 * When next RX descriptor is on a cache-line boundary,
> +		 * prefetch the next 4 RX descriptors and the next 4 pointers
> +		 * to mbufs.
> +		 */
> +		if ((next_id & 0x3) == 0) {
> +			rte_ixgbe_prefetch(&rx_ring[next_id]);
> +			rte_ixgbe_prefetch(&sw_ring[next_id]);
> +		}
> +
> +		rxm = rxe->mbuf;
> +
> +		if (!bulk_alloc) {
> +			__le64 dma =
> +			  rte_cpu_to_le_64(RTE_MBUF_DATA_DMA_ADDR_DEFAULT(nmb));
> +			/*
> +			 * Update RX descriptor with the physical address of the
> +			 * new data buffer of the new allocated mbuf.
> +			 */
> +			rxe->mbuf = nmb;
> +
> +			rxm->data_off = RTE_PKTMBUF_HEADROOM;
> +			rxdp->read.hdr_addr = dma;
> +			rxdp->read.pkt_addr = dma;
> +		} else
> +			rxe->mbuf = NULL;
> +
> +		/*
> +		 * Set data length & data buffer address of mbuf.
> +		 */
> +		data_len = rte_le_to_cpu_16(rxd.wb.upper.length);
> +		rxm->data_len = data_len;
> +
> +		if (!eop) {
> +			uint16_t nextp_id;
> +			/*
> +			 * Get next descriptor index:
> +			 *  - For RSC it's in the NEXTP field.
> +			 *  - For a scattered packet - it's just a following
> +			 *    descriptor.
> +			 */
> +			if (ixgbe_rsc_count(&rxd))
> +				nextp_id =
> +					(staterr & IXGBE_RXDADV_NEXTP_MASK) >>
> +						       IXGBE_RXDADV_NEXTP_SHIFT;
> +			else
> +				nextp_id = next_id;
> +
> +			next_rsc_entry = &sw_rsc_ring[nextp_id];
> +			next_rxe = &sw_ring[nextp_id];
> +			rte_ixgbe_prefetch(next_rxe);
> +		}
> +
> +		rsc_entry = &sw_rsc_ring[rx_id];
> +		first_seg = rsc_entry->fbuf;
> +		rsc_entry->fbuf = NULL;
> +
> +		/*
> +		 * If this is the first buffer of the received packet,
> +		 * set the pointer to the first mbuf of the packet and
> +		 * initialize its context.
> +		 * Otherwise, update the total length and the number of segments
> +		 * of the current scattered packet, and update the pointer to
> +		 * the last mbuf of the current packet.
> +		 */
> +		if (first_seg == NULL) {
> +			first_seg = rxm;
> +			first_seg->pkt_len = data_len;
> +			first_seg->nb_segs = 1;
> +		} else {
> +			first_seg->pkt_len += data_len;
> +			first_seg->nb_segs++;
> +		}
> +
> +		prev_id = rx_id;
> +		rx_id = next_id;
> +
> +		/*
> +		 * If this is not the last buffer of the received packet, update
> +		 * the pointer to the first mbuf at the NEXTP entry in the
> +		 * sw_rsc_ring and continue to parse the RX ring.
> +		 */
> +		if (!eop) {
> +			rxm->next = next_rxe->mbuf;
> +			next_rsc_entry->fbuf = first_seg;
> +			goto next_desc;
> +		}
> +
> +		/*
> +		 * This is the last buffer of the received packet - return
> +		 * the current cluster to the user.
> +		 */
> +		rxm->next = NULL;
> +
> +		/* Initialize the first mbuf of the returned packet */
> +		ixgbe_fill_cluster_head_buf(first_seg, &rxd, rxq->port_id,
> +					    staterr);
> +
> +		/* Prefetch data of first segment, if configured to do so. */
> +		rte_packet_prefetch((char *)first_seg->buf_addr +
> +			first_seg->data_off);
> +
> +		/*
> +		 * Store the mbuf address into the next entry of the array
> +		 * of returned packets.
> +		 */
> +		rx_pkts[nb_rx++] = first_seg;
> +	}
> +
> +	/*
> +	 * Record index of the next RX descriptor to probe.
> +	 */
> +	rxq->rx_tail = rx_id;
> +
> +	/*
> +	 * If the number of free RX descriptors is greater than the RX free
> +	 * threshold of the queue, advance the Receive Descriptor Tail (RDT)
> +	 * register.
> +	 * Update the RDT with the value of the last processed RX descriptor
> +	 * minus 1, to guarantee that the RDT register is never equal to the
> +	 * RDH register, which creates a "full" ring situtation from the
> +	 * hardware point of view...
> +	 */
> +	if (!bulk_alloc && nb_hold > rxq->rx_free_thresh) {
> +		PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_tail=%u "
> +			   "nb_hold=%u nb_rx=%u",
> +			   rxq->port_id, rxq->queue_id, rx_id, nb_hold, nb_rx);
> +
> +		rte_wmb();
> +		IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr, prev_id);
> +		nb_hold = 0;
> +	}
> +
> +	rxq->nb_rx_hold = nb_hold;
> +	return nb_rx;
> +}
> +
> +uint16_t
> +ixgbe_recv_pkts_lro_single_alloc(void *rx_queue, struct rte_mbuf **rx_pkts,
> +				 uint16_t nb_pkts)
> +{
> +	return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, false);
> +}
> +
> +uint16_t
> +ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue, struct rte_mbuf **rx_pkts,
> +			       uint16_t nb_pkts)
> +{
> +	return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, true);
> +}
> +
>  uint16_t
>  ixgbe_recv_scattered_pkts(void *rx_queue, struct rte_mbuf **rx_pkts,
>  			  uint16_t nb_pkts)
> @@ -2005,6 +2295,31 @@ ixgbe_dev_tx_queue_setup(struct rte_eth_dev *dev,
>  	return (0);
>  }
> 
> +/**
> + * ixgbe_free_rsc_cluster - free the not-yet-completed RSC cluster
> + *
> + * The "next" pointer of the last segment of (not-yet-completed) RSC clusters
> + * in the sw_rsc_ring is not set to NULL but rather points to the next
> + * mbuf of this RSC aggregation (that has not been completed yet and still
> + * resides on the HW ring). So, instead of calling for rte_pktmbuf_free() we
> + * will just free first "nb_segs" segments of the cluster explicitly by calling
> + * an rte_pktmbuf_free_seg().
> + *
> + * @m RSC cluster head
> + */
> +static void
> +ixgbe_free_rsc_cluster(struct rte_mbuf *m)
> +{
> +	uint8_t i, nb_segs = m->nb_segs;
> +	struct rte_mbuf *next_seg;
> +
> +	for (i = 0; i < nb_segs; i++) {
> +		next_seg = m->next;
> +		rte_pktmbuf_free_seg(m);
> +		m = next_seg;
> +	}
> +}
> +
>  static void
>  ixgbe_rx_queue_release_mbufs(struct ixgbe_rx_queue *rxq)
>  {
> @@ -2028,6 +2343,13 @@ ixgbe_rx_queue_release_mbufs(struct ixgbe_rx_queue *rxq)
>  		}
>  #endif
>  	}
> +
> +	if (rxq->sw_rsc_ring)
> +		for (i = 0; i < rxq->nb_rx_desc; i++)
> +			if (rxq->sw_rsc_ring[i].fbuf) {
> +				ixgbe_free_rsc_cluster(rxq->sw_rsc_ring[i].fbuf);
> +				rxq->sw_rsc_ring[i].fbuf = NULL;
> +			}
>  }
> 
>  static void
> @@ -2036,6 +2358,7 @@ ixgbe_rx_queue_release(struct ixgbe_rx_queue *rxq)
>  	if (rxq != NULL) {
>  		ixgbe_rx_queue_release_mbufs(rxq);
>  		rte_free(rxq->sw_ring);
> +		rte_free(rxq->sw_rsc_ring);
>  		rte_free(rxq);
>  	}
>  }
> @@ -2158,6 +2481,7 @@ ixgbe_reset_rx_queue(struct ixgbe_hw *hw, struct ixgbe_rx_queue *rxq)
>  	rxq->nb_rx_hold = 0;
>  	rxq->pkt_first_seg = NULL;
>  	rxq->pkt_last_seg = NULL;
> +	rxq->rsc_en = 0;
>  }
> 
>  int
> @@ -2172,6 +2496,14 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev *dev,
>  	struct ixgbe_rx_queue *rxq;
>  	struct ixgbe_hw     *hw;
>  	uint16_t len;
> +	struct rte_eth_dev_info dev_info = { 0 };
> +	struct rte_eth_rxmode *dev_rx_mode = &dev->data->dev_conf.rxmode;
> +	bool rsc_requested = false;
> +
> +	dev->dev_ops->dev_infos_get(dev, &dev_info);
> +	if ((dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO) &&
> +	    dev_rx_mode->enable_lro)
> +		rsc_requested = true;
> 
>  	PMD_INIT_FUNC_TRACE();
>  	hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> @@ -2277,12 +2609,27 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev *dev,
>  	rxq->sw_ring = rte_zmalloc_socket("rxq->sw_ring",
>  					  sizeof(struct ixgbe_rx_entry) * len,
>  					  RTE_CACHE_LINE_SIZE, socket_id);
> -	if (rxq->sw_ring == NULL) {
> +	if (!rxq->sw_ring) {
>  		ixgbe_rx_queue_release(rxq);
>  		return (-ENOMEM);
>  	}
> -	PMD_INIT_LOG(DEBUG, "sw_ring=%p hw_ring=%p dma_addr=0x%"PRIx64,
> -		     rxq->sw_ring, rxq->rx_ring, rxq->rx_ring_phys_addr);
> +
> +	if (rsc_requested) {
> +		rxq->sw_rsc_ring =
> +			rte_zmalloc_socket("rxq->sw_rsc_ring",
> +					   sizeof(struct ixgbe_rsc_entry) * len,
> +					   RTE_CACHE_LINE_SIZE, socket_id);
> +		if (!rxq->sw_rsc_ring) {
> +			ixgbe_rx_queue_release(rxq);
> +			return (-ENOMEM);
> +		}
> +	} else
> +		rxq->sw_rsc_ring = NULL;
> +
> +	PMD_INIT_LOG(DEBUG, "sw_ring=%p sw_rsc_ring=%p hw_ring=%p "
> +			    "dma_addr=0x%"PRIx64,
> +		     rxq->sw_ring, rxq->sw_rsc_ring, rxq->rx_ring,
> +		     rxq->rx_ring_phys_addr);
> 
>  	if (!rte_is_power_of_2(nb_desc)) {
>  		PMD_INIT_LOG(DEBUG, "queue[%d] doesn't meet Vector Rx "
> @@ -3527,6 +3874,91 @@ ixgbe_dev_mq_tx_configure(struct rte_eth_dev *dev)
>  	return 0;
>  }
> 
> +/**
> + * ixgbe_get_rscctl_maxdesc - Calculate the RSCCTL[n].MAXDESC for PF
> + *
> + * Return the RSCCTL[n].MAXDESC for 82599 and x540 PF devices according to the
> + * spec rev. 3.0 chapter 8.2.3.8.13.
> + *
> + * @pool Memory pool of the Rx queue
> + */
> +static inline uint32_t
> +ixgbe_get_rscctl_maxdesc(struct rte_mempool *pool)
> +{
> +	struct rte_pktmbuf_pool_private *mp_priv = rte_mempool_get_priv(pool);
> +
> +	/* MAXDESC * SRRCTL.BSIZEPKT must not exceed 64 KB minus one */
> +	uint16_t maxdesc =
> +		IPV4_MAX_PKT_LEN /
> +			(mp_priv->mbuf_data_room_size - RTE_PKTMBUF_HEADROOM);
> +
> +	if (maxdesc >= 16)
> +		return IXGBE_RSCCTL_MAXDESC_16;
> +	else if (maxdesc >= 8)
> +		return IXGBE_RSCCTL_MAXDESC_8;
> +	else if (maxdesc >= 4)
> +		return IXGBE_RSCCTL_MAXDESC_4;
> +	else
> +		return IXGBE_RSCCTL_MAXDESC_1;
> +}
> +
> +/**
> + * ixgbe_set_ivar - Setup the correct IVAR register for a particular MSIX
> + * interrupt
> + *
> + * (Taken from FreeBSD tree)
> + * (yes this is all very magic and confusing :)
> + *
> + * @dev port handle
> + * @entry the register array entry
> + * @vector the MSIX vector for this queue
> + * @type RX/TX/MISC
> + */
> +static void
> +ixgbe_set_ivar(struct rte_eth_dev *dev, u8 entry, u8 vector, s8 type)
> +{
> +	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> +	u32 ivar, index;
> +
> +	vector |= IXGBE_IVAR_ALLOC_VAL;
> +
> +	switch (hw->mac.type) {
> +
> +	case ixgbe_mac_82598EB:
> +		if (type == -1)
> +			entry = IXGBE_IVAR_OTHER_CAUSES_INDEX;
> +		else
> +			entry += (type * 64);
> +		index = (entry >> 2) & 0x1F;
> +		ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(index));
> +		ivar &= ~(0xFF << (8 * (entry & 0x3)));
> +		ivar |= (vector << (8 * (entry & 0x3)));
> +		IXGBE_WRITE_REG(hw, IXGBE_IVAR(index), ivar);
> +		break;
> +
> +	case ixgbe_mac_82599EB:
> +	case ixgbe_mac_X540:
> +		if (type == -1) { /* MISC IVAR */
> +			index = (entry & 1) * 8;
> +			ivar = IXGBE_READ_REG(hw, IXGBE_IVAR_MISC);
> +			ivar &= ~(0xFF << index);
> +			ivar |= (vector << index);
> +			IXGBE_WRITE_REG(hw, IXGBE_IVAR_MISC, ivar);
> +		} else {	/* RX/TX IVARS */
> +			index = (16 * (entry & 1)) + (8 * type);
> +			ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(entry >> 1));
> +			ivar &= ~(0xFF << index);
> +			ivar |= (vector << index);
> +			IXGBE_WRITE_REG(hw, IXGBE_IVAR(entry >> 1), ivar);
> +		}
> +
> +		break;
> +
> +	default:
> +		break;
> +	}
> +}
> +
>  void ixgbe_set_rx_function(struct rte_eth_dev *dev)
>  {
>  	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> @@ -3545,7 +3977,24 @@ void ixgbe_set_rx_function(struct rte_eth_dev *dev)
>  		hw->rx_vec_allowed = false;
>  	}
> 
> -	if (dev->data->scattered_rx) {
> +	/*
> +	 * Initialize the appropriate LRO callback.
> +	 *
> +	 * If all queues satisfy the bulk allocation preconditions
> +	 * (hw->rx_bulk_alloc_allowed is TRUE) then we may use bulk allocation.
> +	 * Otherwise use a single allocation version.
> +	 */
> +	if (dev->data->lro) {
> +		if (hw->rx_bulk_alloc_allowed) {
> +			PMD_INIT_LOG(INFO, "LRO is requested. Using a bulk "
> +					   "allocation version");
> +			dev->rx_pkt_burst = ixgbe_recv_pkts_lro_bulk_alloc;
> +		} else {
> +			PMD_INIT_LOG(INFO, "LRO is requested. Using a single "
> +					   "allocation version");
> +			dev->rx_pkt_burst = ixgbe_recv_pkts_lro_single_alloc;
> +		}
> +	} else if (dev->data->scattered_rx) {
>  		/*
>  		 * Set the non-LRO scattered callback: there are Vector and
>  		 * single allocation versions.
> @@ -3595,6 +4044,149 @@ void ixgbe_set_rx_function(struct rte_eth_dev *dev)
>  	}
>  }
> 
> +/**
> + * ixgbe_set_rsc - configure RSC related port HW registers
> + *
> + * Configures the port's RSC related registers according to the 4.6.7.2 chapter
> + * of 82599 Spec (x540 configuration is virtually the same).
> + *
> + * @dev port handle
> + *
> + * Returns 0 in case of success or a non-zero error code
> + */
> +static int
> +ixgbe_set_rsc(struct rte_eth_dev *dev)
> +{
> +	struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
> +	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> +	struct rte_eth_dev_info dev_info = { 0 };
> +	bool rsc_capable = false;
> +	uint16_t i;
> +	uint32_t rdrxctl;
> +
> +	/* Sanity check */
> +	dev->dev_ops->dev_infos_get(dev, &dev_info);
> +	if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO)
> +		rsc_capable = true;
> +
> +	if (!rsc_capable && rx_conf->enable_lro) {
> +		PMD_INIT_LOG(CRIT, "LRO is requested on HW that doesn't "
> +				   "support it");
> +		return -EINVAL;
> +	}
> +
> +	/* RSC global configuration (chapter 4.6.7.2.1 of 82599 Spec) */
> +
> +	if (!rx_conf->hw_strip_crc && rx_conf->enable_lro) {
> +		/*
> +		 * According to chapter of 4.6.7.2.1 of the Spec Rev.
> +		 * 3.0 RSC configuration requires HW CRC stripping being
> +		 * enabled. If user requested both HW CRC stripping off
> +		 * and RSC on - return an error.
> +		 */
> +		PMD_INIT_LOG(CRIT, "LRO can't be enabled when HW CRC "
> +				    "is disabled");
> +		return -EINVAL;
> +	}
> +
> +	/* RFCTL configuration  */
> +	if (rsc_capable) {
> +		uint32_t rfctl = IXGBE_READ_REG(hw, IXGBE_RFCTL);
> +		if (rx_conf->enable_lro)
> +			/*
> +			 * Since NFS packets coalescing is not supported - clear
> +			 * RFCTL.NFSW_DIS and RFCTL.NFSR_DIS when RSC is
> +			 * enabled.
> +			 */
> +			rfctl &= ~(IXGBE_RFCTL_RSC_DIS | IXGBE_RFCTL_NFSW_DIS |
> +				   IXGBE_RFCTL_NFSR_DIS);
> +		else
> +			rfctl |= IXGBE_RFCTL_RSC_DIS;
> +
> +		IXGBE_WRITE_REG(hw, IXGBE_RFCTL, rfctl);
> +	}
> +
> +	/* If LRO hasn't been requested - we are done here. */
> +	if (!rx_conf->enable_lro)
> +		return 0;
> +
> +	/* Set RDRXCTL.RSCACKC bit */
> +	rdrxctl = IXGBE_READ_REG(hw, IXGBE_RDRXCTL);
> +	rdrxctl |= IXGBE_RDRXCTL_RSCACKC;
> +	IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
> +
> +	/* Per-queue RSC configuration (chapter 4.6.7.2.2 of 82599 Spec) */
> +	for (i = 0; i < dev->data->nb_rx_queues; i++) {
> +		struct ixgbe_rx_queue *rxq = dev->data->rx_queues[i];
> +		uint32_t srrctl =
> +			IXGBE_READ_REG(hw, IXGBE_SRRCTL(rxq->reg_idx));
> +		uint32_t rscctl =
> +			IXGBE_READ_REG(hw, IXGBE_RSCCTL(rxq->reg_idx));
> +		uint32_t psrtype =
> +			IXGBE_READ_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx));
> +		uint32_t eitr =
> +			IXGBE_READ_REG(hw, IXGBE_EITR(rxq->reg_idx));
> +
> +		/*
> +		 * ixgbe PMD doesn't support header-split at the moment.
> +		 *
> +		 * Following the 4.6.7.2.1 chapter of the 82599/x540
> +		 * Spec if RSC is enabled the SRRCTL[n].BSIZEHEADER
> +		 * should be configured even if header split is not
> +		 * enabled. We will configure it 128 bytes following the
> +		 * recommendation in the spec.
> +		 */
> +		srrctl &= ~IXGBE_SRRCTL_BSIZEHDR_MASK;
> +		srrctl |= (128 << IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT) &
> +					    IXGBE_SRRCTL_BSIZEHDR_MASK;
> +
> +		/*
> +		 * TODO: Consider setting the Receive Descriptor Minimum
> +		 * Threshold Size for an RSC case. This is not an obviously
> +		 * beneficiary option but the one worth considering...
> +		 */
> +
> +		rscctl |= IXGBE_RSCCTL_RSCEN;
> +		rscctl |= ixgbe_get_rscctl_maxdesc(rxq->mb_pool);
> +		psrtype |= IXGBE_PSRTYPE_TCPHDR;
> +
> +		/*
> +		 * RSC: Set ITR interval corresponding to 2K ints/s.
> +		 *
> +		 * Full-sized RSC aggregations for a 10Gb/s link will
> +		 * arrive at about 20K aggregation/s rate.
> +		 *
> +		 * 2K inst/s rate will make only 10% of the
> +		 * aggregations to be closed due to the interrupt timer
> +		 * expiration for a streaming at wire-speed case.
> +		 *
> +		 * For a sparse streaming case this setting will yield
> +		 * at most 500us latency for a single RSC aggregation.
> +		 */
> +		eitr &= ~IXGBE_EITR_ITR_INT_MASK;
> +		eitr |= IXGBE_EITR_INTERVAL_US(500) | IXGBE_EITR_CNT_WDIS;
> +
> +		IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
> +		IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(rxq->reg_idx), rscctl);
> +		IXGBE_WRITE_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx), psrtype);
> +		IXGBE_WRITE_REG(hw, IXGBE_EITR(rxq->reg_idx), eitr);
> +
> +		/*
> +		 * RSC requires the mapping of the queue to the
> +		 * interrupt vector.
> +		 */
> +		ixgbe_set_ivar(dev, rxq->reg_idx, i, 0);
> +
> +		rxq->rsc_en = 1;
> +	}
> +
> +	dev->data->lro = 1;
> +
> +	PMD_INIT_LOG(INFO, "enabling LRO mode");
> +
> +	return 0;
> +}
> +
>  /*
>   * Initializes Receive Unit.
>   */
> @@ -3615,6 +4207,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>  	uint16_t buf_size;
>  	uint16_t i;
>  	struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
> +	int rc;
> 
>  	PMD_INIT_FUNC_TRACE();
>  	hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> @@ -3724,6 +4317,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>  				       RTE_PKTMBUF_HEADROOM);
>  		srrctl |= ((buf_size >> IXGBE_SRRCTL_BSIZEPKT_SHIFT) &
>  			   IXGBE_SRRCTL_BSIZEPKT_MASK);
> +
>  		IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
> 
>  		buf_size = (uint16_t) ((srrctl & IXGBE_SRRCTL_BSIZEPKT_MASK) <<
> @@ -3738,8 +4332,6 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>  	if (rx_conf->enable_scatter)
>  		dev->data->scattered_rx = 1;
> 
> -	ixgbe_set_rx_function(dev);
> -
>  	/*
>  	 * Device configured with multiple RX queues.
>  	 */
> @@ -3770,6 +4362,12 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>  		IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
>  	}
> 
> +	rc = ixgbe_set_rsc(dev);
> +	if (rc)
> +		return rc;
> +
> +	ixgbe_set_rx_function(dev);
> +
>  	return 0;
>  }
> 
> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
> index 3937cf6..120bbbd 100644
> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
> @@ -79,6 +79,10 @@ struct ixgbe_rx_entry {
>  	struct rte_mbuf *mbuf; /**< mbuf associated with RX descriptor. */
>  };
> 
> +struct ixgbe_rsc_entry {
> +	struct rte_mbuf *fbuf; /**< First segment of the fragmented packet. */
> +};
> +
>  /**
>   * Structure associated with each descriptor of the TX ring of a TX queue.
>   */
> @@ -105,6 +109,7 @@ struct ixgbe_rx_queue {
>  	volatile uint32_t   *rdt_reg_addr; /**< RDT register address. */
>  	volatile uint32_t   *rdh_reg_addr; /**< RDH register address. */
>  	struct ixgbe_rx_entry *sw_ring; /**< address of RX software ring. */
> +	struct ixgbe_rsc_entry *sw_rsc_ring; /**< address of RSC software ring. */
>  	struct rte_mbuf *pkt_first_seg; /**< First segment of current packet. */
>  	struct rte_mbuf *pkt_last_seg; /**< Last segment of current packet. */
>  	uint64_t            mbuf_initializer; /**< value to init mbufs */
> @@ -126,6 +131,7 @@ struct ixgbe_rx_queue {
>  	uint8_t             port_id;  /**< Device port identifier. */
>  	uint8_t             crc_len;  /**< 0 if CRC stripped, 4 otherwise. */
>  	uint8_t             drop_en;  /**< If not 0, set SRRCTL.Drop_En. */
> +	uint8_t             rsc_en;   /**< If not 0, RSC is enabled. */
>  	uint8_t             rx_deferred_start; /**< not in global dev start. */
>  #ifdef RTE_LIBRTE_IXGBE_RX_ALLOW_BULK_ALLOC
>  	/** need to alloc dummy mbuf, for wraparound when scanning hw ring */
> --
> 2.1.0

^ permalink raw reply	[flat|nested] 6+ messages in thread

* [dpdk-dev]  [PATCH v8 3/3] ixgbe: Add LRO support
  2015-03-18 17:52 [dpdk-dev] [PATCH v8 0/3]: Add LRO support to ixgbe PMD Vlad Zolotarov
@ 2015-03-18 17:52 ` Vlad Zolotarov
  2015-03-30 14:18   ` Ananyev, Konstantin
  0 siblings, 1 reply; 6+ messages in thread
From: Vlad Zolotarov @ 2015-03-18 17:52 UTC (permalink / raw)
  To: dev

    - Only x540 and 82599 devices support LRO.
    - Add the appropriate HW configuration.
    - Add RSC aware rx_pkt_burst() handlers:
       - Implemented bulk allocation and non-bulk allocation versions.
       - Add LRO-specific fields to rte_eth_rxmode, to rte_eth_dev_data
         and to ixgbe_rx_queue.
       - Use the appropriate handler when LRO is requested.

Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com>
---
New in v8:
   - Took the RSC configuration code from ixgbe_dev_rx_init() into a separate
     function - ixgbe_set_rsc().
   - Added some missing macros for HW configuration.
   - Styling adjustments:
      - Functions names.
      - Functions descriptions.
   - Reworked the ixgbe_free_rsc_cluster() code to make it more readable.
   - Kill the HEADER_SPLIT flow in ixgbe_set_rsc() since it's not supported by
     ixgbe PMD.

New in v7:
   - Free not-yet-completed RSC aggregations in rte_eth_dev_stop() flow.
   - Reset the sw_ring[].mbuf entry in a bulk allocation case.
     This is needed for ixgbe_rx_queue_release_mbufs().
   - _recv_pkts_lro(): added the missing memory barrier before RDT update in a
     non-bulk allocation case.
   - Don't allow RSC when device is configured in an SR-IOV mode.

New in v5:
   - Put the RTE_ETHDEV_HAS_LRO_SUPPORT definition at the beginning of rte_ethdev.h.
   - Removed the "TODO: Remove me" comment near RTE_ETHDEV_HAS_LRO_SUPPORT.

New in v4:
   - Define RTE_ETHDEV_HAS_LRO_SUPPORT in rte_ethdev.h instead of
     RTE_ETHDEV_LRO_SUPPORT defined in config/common_linuxapp.

New in v2:
   - Removed rte_eth_dev_data.lro_bulk_alloc.
   - Fixed a few styling and spelling issues.
---
 lib/librte_ether/rte_ethdev.h           |   9 +-
 lib/librte_net/rte_ip.h                 |   3 +
 lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h |   6 +
 lib/librte_pmd_ixgbe/ixgbe_ethdev.c     |  11 +
 lib/librte_pmd_ixgbe/ixgbe_ethdev.h     |   5 +
 lib/librte_pmd_ixgbe/ixgbe_rxtx.c       | 610 +++++++++++++++++++++++++++++++-
 lib/librte_pmd_ixgbe/ixgbe_rxtx.h       |   6 +
 7 files changed, 642 insertions(+), 8 deletions(-)

diff --git a/lib/librte_ether/rte_ethdev.h b/lib/librte_ether/rte_ethdev.h
index 21aa359..61dc49a 100644
--- a/lib/librte_ether/rte_ethdev.h
+++ b/lib/librte_ether/rte_ethdev.h
@@ -172,6 +172,9 @@ extern "C" {
 
 #include <stdint.h>
 
+/* Use this macro to check if LRO API is supported */
+#define RTE_ETHDEV_HAS_LRO_SUPPORT
+
 #include <rte_log.h>
 #include <rte_interrupts.h>
 #include <rte_pci.h>
@@ -320,14 +323,15 @@ struct rte_eth_rxmode {
 	enum rte_eth_rx_mq_mode mq_mode;
 	uint32_t max_rx_pkt_len;  /**< Only used if jumbo_frame enabled. */
 	uint16_t split_hdr_size;  /**< hdr buf size (header_split enabled).*/
-	uint8_t header_split : 1, /**< Header Split enable. */
+	uint16_t header_split : 1, /**< Header Split enable. */
 		hw_ip_checksum   : 1, /**< IP/UDP/TCP checksum offload enable. */
 		hw_vlan_filter   : 1, /**< VLAN filter enable. */
 		hw_vlan_strip    : 1, /**< VLAN strip enable. */
 		hw_vlan_extend   : 1, /**< Extended VLAN enable. */
 		jumbo_frame      : 1, /**< Jumbo Frame Receipt enable. */
 		hw_strip_crc     : 1, /**< Enable CRC stripping by hardware. */
-		enable_scatter   : 1; /**< Enable scatter packets rx handler */
+		enable_scatter   : 1, /**< Enable scatter packets rx handler */
+		enable_lro       : 1; /**< Enable LRO */
 };
 
 /**
@@ -1515,6 +1519,7 @@ struct rte_eth_dev_data {
 	uint8_t port_id;           /**< Device [external] port identifier. */
 	uint8_t promiscuous   : 1, /**< RX promiscuous mode ON(1) / OFF(0). */
 		scattered_rx : 1,  /**< RX of scattered packets is ON(1) / OFF(0) */
+		lro          : 1,  /**< RX LRO is ON(1) / OFF(0) */
 		all_multicast : 1, /**< RX all multicast mode ON(1) / OFF(0). */
 		dev_started : 1;   /**< Device state: STARTED(1) / STOPPED(0). */
 };
diff --git a/lib/librte_net/rte_ip.h b/lib/librte_net/rte_ip.h
index 64935d9..74c9ced 100644
--- a/lib/librte_net/rte_ip.h
+++ b/lib/librte_net/rte_ip.h
@@ -110,6 +110,9 @@ struct ipv4_hdr {
 					   (((c) & 0xff) << 8)  | \
 					   ((d) & 0xff))
 
+/** Maximal IPv4 packet length (including a header) */
+#define IPV4_MAX_PKT_LEN        65535
+
 /** Internet header length mask for version_ihl field */
 #define IPV4_HDR_IHL_MASK	(0x0f)
 /**
diff --git a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
index 9a66370..4998627 100644
--- a/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
+++ b/lib/librte_pmd_ixgbe/ixgbe/ixgbe_type.h
@@ -234,8 +234,14 @@ struct ixgbe_thermal_sensor_data {
 #define IXGBE_EITR(_i)		(((_i) <= 23) ? (0x00820 + ((_i) * 4)) : \
 				 (0x012300 + (((_i) - 24) * 4)))
 #define IXGBE_EITR_ITR_INT_MASK	0x00000FF8
+#define IXGBE_EITR_ITR_INT_SHIFT 3
 #define IXGBE_EITR_LLI_MOD	0x00008000
 #define IXGBE_EITR_CNT_WDIS	0x80000000
+/* EITR Inteval is in 2048ns uinits for 1G and 10G link */
+#define IXGBE_EITR_INTERVAL_UNIT_NS	2048
+#define IXGBE_EITR_INTERVAL_US(us)	\
+   (((us) * 1000 / IXGBE_EITR_INTERVAL_UNIT_NS << IXGBE_EITR_ITR_INT_SHIFT) & \
+		IXGBE_EITR_ITR_INT_MASK)
 #define IXGBE_IVAR(_i)		(0x00900 + ((_i) * 4)) /* 24 at 0x900-0x960 */
 #define IXGBE_IVAR_MISC		0x00A00 /* misc MSI-X interrupt causes */
 #define IXGBE_EITRSEL		0x00894
diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
index 92d75db..923692e 100644
--- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
+++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.c
@@ -1645,6 +1645,7 @@ ixgbe_dev_stop(struct rte_eth_dev *dev)
 
 	/* Clear stored conf */
 	dev->data->scattered_rx = 0;
+	dev->data->lro = 0;
 
 	/* Clear recorded link status */
 	memset(&link, 0, sizeof(link));
@@ -2013,6 +2014,16 @@ ixgbe_dev_info_get(struct rte_eth_dev *dev, struct rte_eth_dev_info *dev_info)
 		DEV_RX_OFFLOAD_IPV4_CKSUM |
 		DEV_RX_OFFLOAD_UDP_CKSUM  |
 		DEV_RX_OFFLOAD_TCP_CKSUM;
+
+	/*
+	 * RSC is only supported by 82599 and x540 PF devices in a non-SR-IOV
+	 * mode.
+	 */
+	if ((hw->mac.type == ixgbe_mac_82599EB ||
+	     hw->mac.type == ixgbe_mac_X540) &&
+	    !RTE_ETH_DEV_SRIOV(dev).active)
+		dev_info->rx_offload_capa |= DEV_RX_OFFLOAD_TCP_LRO;
+
 	dev_info->tx_offload_capa =
 		DEV_TX_OFFLOAD_VLAN_INSERT |
 		DEV_TX_OFFLOAD_IPV4_CKSUM  |
diff --git a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
index ffe3471..7050340 100644
--- a/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
+++ b/lib/librte_pmd_ixgbe/ixgbe_ethdev.h
@@ -344,6 +344,11 @@ uint16_t ixgbe_recv_pkts(void *rx_queue, struct rte_mbuf **rx_pkts,
 uint16_t ixgbe_recv_scattered_pkts(void *rx_queue,
 		struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
 
+uint16_t ixgbe_recv_pkts_lro_single_alloc(void *rx_queue,
+		struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
+uint16_t ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue,
+		struct rte_mbuf **rx_pkts, uint16_t nb_pkts);
+
 uint16_t ixgbe_xmit_pkts(void *tx_queue, struct rte_mbuf **tx_pkts,
 		uint16_t nb_pkts);
 
diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
index a08ae6a..daa4c45 100644
--- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
+++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.c
@@ -70,6 +70,7 @@
 #include <rte_sctp.h>
 #include <rte_string_fns.h>
 #include <rte_errno.h>
+#include <rte_ip.h>
 
 #include "ixgbe_logs.h"
 #include "ixgbe/ixgbe_api.h"
@@ -1422,6 +1423,295 @@ ixgbe_fill_cluster_head_buf(
 	}
 }
 
+/**
+ * ixgbe_recv_pkts_lro - receive handler for and LRO case.
+ *
+ * @rx_queue Rx queue handle
+ * @rx_pkts table of received packets
+ * @nb_pkts size of rx_pkts table
+ * @bulk_alloc if TRUE bulk allocation is used for a HW ring refilling
+ *
+ * Handles the Rx HW ring completions when RSC feature is configured. Uses an
+ * additional ring of ixgbe_rsc_entry's that will hold the relevant RSC info.
+ *
+ * We use the same logic as in Lunux and in FreeBSD ixgbe drivers:
+ * 1) When non-EOP RSC completion arrives:
+ *    a) Update the HEAD of the current RSC aggregation cluster with the new
+ *       segment's data length.
+ *    b) Set the "next" pointer of the current segment to point to the segment
+ *       at the NEXTP index.
+ *    c) Pass the HEAD of RSC aggregation cluster on to the next NEXTP entry
+ *       in the sw_rsc_ring.
+ * 2) When EOP arrives we just update the cluster's total length and offload
+ *    flags and deliver the cluster up to the upper layers. In our case - put it
+ *    in the rx_pkts table.
+ *
+ * Returns the number of received packets/clusters (according to the "bulk
+ * receive" interface).
+ */
+static inline uint16_t
+ixgbe_recv_pkts_lro(void *rx_queue, struct rte_mbuf **rx_pkts, uint16_t nb_pkts,
+		    bool bulk_alloc)
+{
+	struct ixgbe_rx_queue *rxq = rx_queue;
+	volatile union ixgbe_adv_rx_desc *rx_ring = rxq->rx_ring;
+	struct ixgbe_rx_entry *sw_ring = rxq->sw_ring;
+	struct ixgbe_rsc_entry *sw_rsc_ring = rxq->sw_rsc_ring;
+	uint16_t rx_id = rxq->rx_tail;
+	uint16_t nb_rx = 0;
+	uint16_t nb_hold = rxq->nb_rx_hold;
+	uint16_t prev_id = rxq->rx_tail;
+
+	while (nb_rx < nb_pkts) {
+		bool eop;
+		struct ixgbe_rx_entry *rxe;
+		struct ixgbe_rsc_entry *rsc_entry;
+		struct ixgbe_rsc_entry *next_rsc_entry;
+		struct ixgbe_rx_entry *next_rxe;
+		struct rte_mbuf *first_seg;
+		struct rte_mbuf *rxm;
+		struct rte_mbuf *nmb;
+		union ixgbe_adv_rx_desc rxd;
+		uint16_t data_len;
+		uint16_t next_id;
+		volatile union ixgbe_adv_rx_desc *rxdp;
+		uint32_t staterr;
+
+next_desc:
+		/*
+		 * The code in this whole file uses the volatile pointer to
+		 * ensure the read ordering of the status and the rest of the
+		 * descriptor fields (on the compiler level only!!!). This is so
+		 * UGLY - why not to just use the compiler barrier instead? DPDK
+		 * even has the rte_compiler_barrier() for that.
+		 *
+		 * But most importantly this is just wrong because this doesn't
+		 * ensure memory ordering in a general case at all. For
+		 * instance, DPDK is supposed to work on Power CPUs where
+		 * compiler barrier may just not be enough!
+		 *
+		 * I tried to write only this function properly to have a
+		 * starting point (as a part of an LRO/RSC series) but the
+		 * compiler cursed at me when I tried to cast away the
+		 * "volatile" from rx_ring (yes, it's volatile too!!!). So, I'm
+		 * keeping it the way it is for now.
+		 *
+		 * The code in this file is broken in so many other places and
+		 * will just not work on a big endian CPU anyway therefore the
+		 * lines below will have to be revisited together with the rest
+		 * of the ixgbe PMD.
+		 *
+		 * TODO:
+		 *    - Get rid of "volatile" crap and let the compiler do its
+		 *      job.
+		 *    - Use the proper memory barrier (rte_rmb()) to ensure the
+		 *      memory ordering below.
+		 */
+		rxdp = &rx_ring[rx_id];
+		staterr = rte_le_to_cpu_32(rxdp->wb.upper.status_error);
+
+		if (!(staterr & IXGBE_RXDADV_STAT_DD))
+			break;
+
+		rxd = *rxdp;
+
+		PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_id=%u "
+				  "staterr=0x%x data_len=%u",
+			   rxq->port_id, rxq->queue_id, rx_id, staterr,
+			   rte_le_to_cpu_16(rxd.wb.upper.length));
+
+		if (!bulk_alloc) {
+			nmb = rte_rxmbuf_alloc(rxq->mb_pool);
+			if (nmb == NULL) {
+				PMD_RX_LOG(DEBUG, "RX mbuf alloc failed "
+						  "port_id=%u queue_id=%u",
+					   rxq->port_id, rxq->queue_id);
+
+				rte_eth_devices[rxq->port_id].data->
+							rx_mbuf_alloc_failed++;
+				break;
+			}
+		} else if (nb_hold > rxq->rx_free_thresh) {
+			uint16_t next_rdt = rxq->rx_free_trigger;
+
+			if (!ixgbe_rx_alloc_bufs(rxq, false)) {
+				rte_wmb();
+				IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr,
+						    next_rdt);
+				nb_hold -= rxq->rx_free_thresh;
+			} else {
+				PMD_RX_LOG(DEBUG, "RX bulk alloc failed "
+						  "port_id=%u queue_id=%u",
+					   rxq->port_id, rxq->queue_id);
+
+				rte_eth_devices[rxq->port_id].data->
+							rx_mbuf_alloc_failed++;
+				break;
+			}
+		}
+
+		nb_hold++;
+		rxe = &sw_ring[rx_id];
+		eop = staterr & IXGBE_RXDADV_STAT_EOP;
+
+		next_id = rx_id + 1;
+		if (next_id == rxq->nb_rx_desc)
+			next_id = 0;
+
+		/* Prefetch next mbuf while processing current one. */
+		rte_ixgbe_prefetch(sw_ring[next_id].mbuf);
+
+		/*
+		 * When next RX descriptor is on a cache-line boundary,
+		 * prefetch the next 4 RX descriptors and the next 4 pointers
+		 * to mbufs.
+		 */
+		if ((next_id & 0x3) == 0) {
+			rte_ixgbe_prefetch(&rx_ring[next_id]);
+			rte_ixgbe_prefetch(&sw_ring[next_id]);
+		}
+
+		rxm = rxe->mbuf;
+
+		if (!bulk_alloc) {
+			__le64 dma =
+			  rte_cpu_to_le_64(RTE_MBUF_DATA_DMA_ADDR_DEFAULT(nmb));
+			/*
+			 * Update RX descriptor with the physical address of the
+			 * new data buffer of the new allocated mbuf.
+			 */
+			rxe->mbuf = nmb;
+
+			rxm->data_off = RTE_PKTMBUF_HEADROOM;
+			rxdp->read.hdr_addr = dma;
+			rxdp->read.pkt_addr = dma;
+		} else
+			rxe->mbuf = NULL;
+
+		/*
+		 * Set data length & data buffer address of mbuf.
+		 */
+		data_len = rte_le_to_cpu_16(rxd.wb.upper.length);
+		rxm->data_len = data_len;
+
+		if (!eop) {
+			uint16_t nextp_id;
+			/*
+			 * Get next descriptor index:
+			 *  - For RSC it's in the NEXTP field.
+			 *  - For a scattered packet - it's just a following
+			 *    descriptor.
+			 */
+			if (ixgbe_rsc_count(&rxd))
+				nextp_id =
+					(staterr & IXGBE_RXDADV_NEXTP_MASK) >>
+						       IXGBE_RXDADV_NEXTP_SHIFT;
+			else
+				nextp_id = next_id;
+
+			next_rsc_entry = &sw_rsc_ring[nextp_id];
+			next_rxe = &sw_ring[nextp_id];
+			rte_ixgbe_prefetch(next_rxe);
+		}
+
+		rsc_entry = &sw_rsc_ring[rx_id];
+		first_seg = rsc_entry->fbuf;
+		rsc_entry->fbuf = NULL;
+
+		/*
+		 * If this is the first buffer of the received packet,
+		 * set the pointer to the first mbuf of the packet and
+		 * initialize its context.
+		 * Otherwise, update the total length and the number of segments
+		 * of the current scattered packet, and update the pointer to
+		 * the last mbuf of the current packet.
+		 */
+		if (first_seg == NULL) {
+			first_seg = rxm;
+			first_seg->pkt_len = data_len;
+			first_seg->nb_segs = 1;
+		} else {
+			first_seg->pkt_len += data_len;
+			first_seg->nb_segs++;
+		}
+
+		prev_id = rx_id;
+		rx_id = next_id;
+
+		/*
+		 * If this is not the last buffer of the received packet, update
+		 * the pointer to the first mbuf at the NEXTP entry in the
+		 * sw_rsc_ring and continue to parse the RX ring.
+		 */
+		if (!eop) {
+			rxm->next = next_rxe->mbuf;
+			next_rsc_entry->fbuf = first_seg;
+			goto next_desc;
+		}
+
+		/*
+		 * This is the last buffer of the received packet - return
+		 * the current cluster to the user.
+		 */
+		rxm->next = NULL;
+
+		/* Initialize the first mbuf of the returned packet */
+		ixgbe_fill_cluster_head_buf(first_seg, &rxd, rxq->port_id,
+					    staterr);
+
+		/* Prefetch data of first segment, if configured to do so. */
+		rte_packet_prefetch((char *)first_seg->buf_addr +
+			first_seg->data_off);
+
+		/*
+		 * Store the mbuf address into the next entry of the array
+		 * of returned packets.
+		 */
+		rx_pkts[nb_rx++] = first_seg;
+	}
+
+	/*
+	 * Record index of the next RX descriptor to probe.
+	 */
+	rxq->rx_tail = rx_id;
+
+	/*
+	 * If the number of free RX descriptors is greater than the RX free
+	 * threshold of the queue, advance the Receive Descriptor Tail (RDT)
+	 * register.
+	 * Update the RDT with the value of the last processed RX descriptor
+	 * minus 1, to guarantee that the RDT register is never equal to the
+	 * RDH register, which creates a "full" ring situtation from the
+	 * hardware point of view...
+	 */
+	if (!bulk_alloc && nb_hold > rxq->rx_free_thresh) {
+		PMD_RX_LOG(DEBUG, "port_id=%u queue_id=%u rx_tail=%u "
+			   "nb_hold=%u nb_rx=%u",
+			   rxq->port_id, rxq->queue_id, rx_id, nb_hold, nb_rx);
+
+		rte_wmb();
+		IXGBE_PCI_REG_WRITE(rxq->rdt_reg_addr, prev_id);
+		nb_hold = 0;
+	}
+
+	rxq->nb_rx_hold = nb_hold;
+	return nb_rx;
+}
+
+uint16_t
+ixgbe_recv_pkts_lro_single_alloc(void *rx_queue, struct rte_mbuf **rx_pkts,
+				 uint16_t nb_pkts)
+{
+	return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, false);
+}
+
+uint16_t
+ixgbe_recv_pkts_lro_bulk_alloc(void *rx_queue, struct rte_mbuf **rx_pkts,
+			       uint16_t nb_pkts)
+{
+	return ixgbe_recv_pkts_lro(rx_queue, rx_pkts, nb_pkts, true);
+}
+
 uint16_t
 ixgbe_recv_scattered_pkts(void *rx_queue, struct rte_mbuf **rx_pkts,
 			  uint16_t nb_pkts)
@@ -2005,6 +2295,31 @@ ixgbe_dev_tx_queue_setup(struct rte_eth_dev *dev,
 	return (0);
 }
 
+/**
+ * ixgbe_free_rsc_cluster - free the not-yet-completed RSC cluster
+ *
+ * The "next" pointer of the last segment of (not-yet-completed) RSC clusters
+ * in the sw_rsc_ring is not set to NULL but rather points to the next
+ * mbuf of this RSC aggregation (that has not been completed yet and still
+ * resides on the HW ring). So, instead of calling for rte_pktmbuf_free() we
+ * will just free first "nb_segs" segments of the cluster explicitly by calling
+ * an rte_pktmbuf_free_seg().
+ *
+ * @m RSC cluster head
+ */
+static void
+ixgbe_free_rsc_cluster(struct rte_mbuf *m)
+{
+	uint8_t i, nb_segs = m->nb_segs;
+	struct rte_mbuf *next_seg;
+
+	for (i = 0; i < nb_segs; i++) {
+		next_seg = m->next;
+		rte_pktmbuf_free_seg(m);
+		m = next_seg;
+	}
+}
+
 static void
 ixgbe_rx_queue_release_mbufs(struct ixgbe_rx_queue *rxq)
 {
@@ -2028,6 +2343,13 @@ ixgbe_rx_queue_release_mbufs(struct ixgbe_rx_queue *rxq)
 		}
 #endif
 	}
+
+	if (rxq->sw_rsc_ring)
+		for (i = 0; i < rxq->nb_rx_desc; i++)
+			if (rxq->sw_rsc_ring[i].fbuf) {
+				ixgbe_free_rsc_cluster(rxq->sw_rsc_ring[i].fbuf);
+				rxq->sw_rsc_ring[i].fbuf = NULL;
+			}
 }
 
 static void
@@ -2036,6 +2358,7 @@ ixgbe_rx_queue_release(struct ixgbe_rx_queue *rxq)
 	if (rxq != NULL) {
 		ixgbe_rx_queue_release_mbufs(rxq);
 		rte_free(rxq->sw_ring);
+		rte_free(rxq->sw_rsc_ring);
 		rte_free(rxq);
 	}
 }
@@ -2158,6 +2481,7 @@ ixgbe_reset_rx_queue(struct ixgbe_hw *hw, struct ixgbe_rx_queue *rxq)
 	rxq->nb_rx_hold = 0;
 	rxq->pkt_first_seg = NULL;
 	rxq->pkt_last_seg = NULL;
+	rxq->rsc_en = 0;
 }
 
 int
@@ -2172,6 +2496,14 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev *dev,
 	struct ixgbe_rx_queue *rxq;
 	struct ixgbe_hw     *hw;
 	uint16_t len;
+	struct rte_eth_dev_info dev_info = { 0 };
+	struct rte_eth_rxmode *dev_rx_mode = &dev->data->dev_conf.rxmode;
+	bool rsc_requested = false;
+
+	dev->dev_ops->dev_infos_get(dev, &dev_info);
+	if ((dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO) &&
+	    dev_rx_mode->enable_lro)
+		rsc_requested = true;
 
 	PMD_INIT_FUNC_TRACE();
 	hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
@@ -2277,12 +2609,27 @@ ixgbe_dev_rx_queue_setup(struct rte_eth_dev *dev,
 	rxq->sw_ring = rte_zmalloc_socket("rxq->sw_ring",
 					  sizeof(struct ixgbe_rx_entry) * len,
 					  RTE_CACHE_LINE_SIZE, socket_id);
-	if (rxq->sw_ring == NULL) {
+	if (!rxq->sw_ring) {
 		ixgbe_rx_queue_release(rxq);
 		return (-ENOMEM);
 	}
-	PMD_INIT_LOG(DEBUG, "sw_ring=%p hw_ring=%p dma_addr=0x%"PRIx64,
-		     rxq->sw_ring, rxq->rx_ring, rxq->rx_ring_phys_addr);
+
+	if (rsc_requested) {
+		rxq->sw_rsc_ring =
+			rte_zmalloc_socket("rxq->sw_rsc_ring",
+					   sizeof(struct ixgbe_rsc_entry) * len,
+					   RTE_CACHE_LINE_SIZE, socket_id);
+		if (!rxq->sw_rsc_ring) {
+			ixgbe_rx_queue_release(rxq);
+			return (-ENOMEM);
+		}
+	} else
+		rxq->sw_rsc_ring = NULL;
+
+	PMD_INIT_LOG(DEBUG, "sw_ring=%p sw_rsc_ring=%p hw_ring=%p "
+			    "dma_addr=0x%"PRIx64,
+		     rxq->sw_ring, rxq->sw_rsc_ring, rxq->rx_ring,
+		     rxq->rx_ring_phys_addr);
 
 	if (!rte_is_power_of_2(nb_desc)) {
 		PMD_INIT_LOG(DEBUG, "queue[%d] doesn't meet Vector Rx "
@@ -3527,6 +3874,91 @@ ixgbe_dev_mq_tx_configure(struct rte_eth_dev *dev)
 	return 0;
 }
 
+/**
+ * ixgbe_get_rscctl_maxdesc - Calculate the RSCCTL[n].MAXDESC for PF
+ *
+ * Return the RSCCTL[n].MAXDESC for 82599 and x540 PF devices according to the
+ * spec rev. 3.0 chapter 8.2.3.8.13.
+ *
+ * @pool Memory pool of the Rx queue
+ */
+static inline uint32_t
+ixgbe_get_rscctl_maxdesc(struct rte_mempool *pool)
+{
+	struct rte_pktmbuf_pool_private *mp_priv = rte_mempool_get_priv(pool);
+
+	/* MAXDESC * SRRCTL.BSIZEPKT must not exceed 64 KB minus one */
+	uint16_t maxdesc =
+		IPV4_MAX_PKT_LEN /
+			(mp_priv->mbuf_data_room_size - RTE_PKTMBUF_HEADROOM);
+
+	if (maxdesc >= 16)
+		return IXGBE_RSCCTL_MAXDESC_16;
+	else if (maxdesc >= 8)
+		return IXGBE_RSCCTL_MAXDESC_8;
+	else if (maxdesc >= 4)
+		return IXGBE_RSCCTL_MAXDESC_4;
+	else
+		return IXGBE_RSCCTL_MAXDESC_1;
+}
+
+/**
+ * ixgbe_set_ivar - Setup the correct IVAR register for a particular MSIX
+ * interrupt
+ *
+ * (Taken from FreeBSD tree)
+ * (yes this is all very magic and confusing :)
+ *
+ * @dev port handle
+ * @entry the register array entry
+ * @vector the MSIX vector for this queue
+ * @type RX/TX/MISC
+ */
+static void
+ixgbe_set_ivar(struct rte_eth_dev *dev, u8 entry, u8 vector, s8 type)
+{
+	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
+	u32 ivar, index;
+
+	vector |= IXGBE_IVAR_ALLOC_VAL;
+
+	switch (hw->mac.type) {
+
+	case ixgbe_mac_82598EB:
+		if (type == -1)
+			entry = IXGBE_IVAR_OTHER_CAUSES_INDEX;
+		else
+			entry += (type * 64);
+		index = (entry >> 2) & 0x1F;
+		ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(index));
+		ivar &= ~(0xFF << (8 * (entry & 0x3)));
+		ivar |= (vector << (8 * (entry & 0x3)));
+		IXGBE_WRITE_REG(hw, IXGBE_IVAR(index), ivar);
+		break;
+
+	case ixgbe_mac_82599EB:
+	case ixgbe_mac_X540:
+		if (type == -1) { /* MISC IVAR */
+			index = (entry & 1) * 8;
+			ivar = IXGBE_READ_REG(hw, IXGBE_IVAR_MISC);
+			ivar &= ~(0xFF << index);
+			ivar |= (vector << index);
+			IXGBE_WRITE_REG(hw, IXGBE_IVAR_MISC, ivar);
+		} else {	/* RX/TX IVARS */
+			index = (16 * (entry & 1)) + (8 * type);
+			ivar = IXGBE_READ_REG(hw, IXGBE_IVAR(entry >> 1));
+			ivar &= ~(0xFF << index);
+			ivar |= (vector << index);
+			IXGBE_WRITE_REG(hw, IXGBE_IVAR(entry >> 1), ivar);
+		}
+
+		break;
+
+	default:
+		break;
+	}
+}
+
 void ixgbe_set_rx_function(struct rte_eth_dev *dev)
 {
 	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
@@ -3545,7 +3977,24 @@ void ixgbe_set_rx_function(struct rte_eth_dev *dev)
 		hw->rx_vec_allowed = false;
 	}
 
-	if (dev->data->scattered_rx) {
+	/*
+	 * Initialize the appropriate LRO callback.
+	 *
+	 * If all queues satisfy the bulk allocation preconditions
+	 * (hw->rx_bulk_alloc_allowed is TRUE) then we may use bulk allocation.
+	 * Otherwise use a single allocation version.
+	 */
+	if (dev->data->lro) {
+		if (hw->rx_bulk_alloc_allowed) {
+			PMD_INIT_LOG(INFO, "LRO is requested. Using a bulk "
+					   "allocation version");
+			dev->rx_pkt_burst = ixgbe_recv_pkts_lro_bulk_alloc;
+		} else {
+			PMD_INIT_LOG(INFO, "LRO is requested. Using a single "
+					   "allocation version");
+			dev->rx_pkt_burst = ixgbe_recv_pkts_lro_single_alloc;
+		}
+	} else if (dev->data->scattered_rx) {
 		/*
 		 * Set the non-LRO scattered callback: there are Vector and
 		 * single allocation versions.
@@ -3595,6 +4044,149 @@ void ixgbe_set_rx_function(struct rte_eth_dev *dev)
 	}
 }
 
+/**
+ * ixgbe_set_rsc - configure RSC related port HW registers
+ *
+ * Configures the port's RSC related registers according to the 4.6.7.2 chapter
+ * of 82599 Spec (x540 configuration is virtually the same).
+ *
+ * @dev port handle
+ *
+ * Returns 0 in case of success or a non-zero error code
+ */
+static int
+ixgbe_set_rsc(struct rte_eth_dev *dev)
+{
+	struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
+	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
+	struct rte_eth_dev_info dev_info = { 0 };
+	bool rsc_capable = false;
+	uint16_t i;
+	uint32_t rdrxctl;
+
+	/* Sanity check */
+	dev->dev_ops->dev_infos_get(dev, &dev_info);
+	if (dev_info.rx_offload_capa & DEV_RX_OFFLOAD_TCP_LRO)
+		rsc_capable = true;
+
+	if (!rsc_capable && rx_conf->enable_lro) {
+		PMD_INIT_LOG(CRIT, "LRO is requested on HW that doesn't "
+				   "support it");
+		return -EINVAL;
+	}
+
+	/* RSC global configuration (chapter 4.6.7.2.1 of 82599 Spec) */
+
+	if (!rx_conf->hw_strip_crc && rx_conf->enable_lro) {
+		/*
+		 * According to chapter of 4.6.7.2.1 of the Spec Rev.
+		 * 3.0 RSC configuration requires HW CRC stripping being
+		 * enabled. If user requested both HW CRC stripping off
+		 * and RSC on - return an error.
+		 */
+		PMD_INIT_LOG(CRIT, "LRO can't be enabled when HW CRC "
+				    "is disabled");
+		return -EINVAL;
+	}
+
+	/* RFCTL configuration  */
+	if (rsc_capable) {
+		uint32_t rfctl = IXGBE_READ_REG(hw, IXGBE_RFCTL);
+		if (rx_conf->enable_lro)
+			/*
+			 * Since NFS packets coalescing is not supported - clear
+			 * RFCTL.NFSW_DIS and RFCTL.NFSR_DIS when RSC is
+			 * enabled.
+			 */
+			rfctl &= ~(IXGBE_RFCTL_RSC_DIS | IXGBE_RFCTL_NFSW_DIS |
+				   IXGBE_RFCTL_NFSR_DIS);
+		else
+			rfctl |= IXGBE_RFCTL_RSC_DIS;
+
+		IXGBE_WRITE_REG(hw, IXGBE_RFCTL, rfctl);
+	}
+
+	/* If LRO hasn't been requested - we are done here. */
+	if (!rx_conf->enable_lro)
+		return 0;
+
+	/* Set RDRXCTL.RSCACKC bit */
+	rdrxctl = IXGBE_READ_REG(hw, IXGBE_RDRXCTL);
+	rdrxctl |= IXGBE_RDRXCTL_RSCACKC;
+	IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
+
+	/* Per-queue RSC configuration (chapter 4.6.7.2.2 of 82599 Spec) */
+	for (i = 0; i < dev->data->nb_rx_queues; i++) {
+		struct ixgbe_rx_queue *rxq = dev->data->rx_queues[i];
+		uint32_t srrctl =
+			IXGBE_READ_REG(hw, IXGBE_SRRCTL(rxq->reg_idx));
+		uint32_t rscctl =
+			IXGBE_READ_REG(hw, IXGBE_RSCCTL(rxq->reg_idx));
+		uint32_t psrtype =
+			IXGBE_READ_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx));
+		uint32_t eitr =
+			IXGBE_READ_REG(hw, IXGBE_EITR(rxq->reg_idx));
+
+		/*
+		 * ixgbe PMD doesn't support header-split at the moment.
+		 *
+		 * Following the 4.6.7.2.1 chapter of the 82599/x540
+		 * Spec if RSC is enabled the SRRCTL[n].BSIZEHEADER
+		 * should be configured even if header split is not
+		 * enabled. We will configure it 128 bytes following the
+		 * recommendation in the spec.
+		 */
+		srrctl &= ~IXGBE_SRRCTL_BSIZEHDR_MASK;
+		srrctl |= (128 << IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT) &
+					    IXGBE_SRRCTL_BSIZEHDR_MASK;
+
+		/*
+		 * TODO: Consider setting the Receive Descriptor Minimum
+		 * Threshold Size for an RSC case. This is not an obviously
+		 * beneficiary option but the one worth considering...
+		 */
+
+		rscctl |= IXGBE_RSCCTL_RSCEN;
+		rscctl |= ixgbe_get_rscctl_maxdesc(rxq->mb_pool);
+		psrtype |= IXGBE_PSRTYPE_TCPHDR;
+
+		/*
+		 * RSC: Set ITR interval corresponding to 2K ints/s.
+		 *
+		 * Full-sized RSC aggregations for a 10Gb/s link will
+		 * arrive at about 20K aggregation/s rate.
+		 *
+		 * 2K inst/s rate will make only 10% of the
+		 * aggregations to be closed due to the interrupt timer
+		 * expiration for a streaming at wire-speed case.
+		 *
+		 * For a sparse streaming case this setting will yield
+		 * at most 500us latency for a single RSC aggregation.
+		 */
+		eitr &= ~IXGBE_EITR_ITR_INT_MASK;
+		eitr |= IXGBE_EITR_INTERVAL_US(500) | IXGBE_EITR_CNT_WDIS;
+
+		IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
+		IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(rxq->reg_idx), rscctl);
+		IXGBE_WRITE_REG(hw, IXGBE_PSRTYPE(rxq->reg_idx), psrtype);
+		IXGBE_WRITE_REG(hw, IXGBE_EITR(rxq->reg_idx), eitr);
+
+		/*
+		 * RSC requires the mapping of the queue to the
+		 * interrupt vector.
+		 */
+		ixgbe_set_ivar(dev, rxq->reg_idx, i, 0);
+
+		rxq->rsc_en = 1;
+	}
+
+	dev->data->lro = 1;
+
+	PMD_INIT_LOG(INFO, "enabling LRO mode");
+
+	return 0;
+}
+
 /*
  * Initializes Receive Unit.
  */
@@ -3615,6 +4207,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 	uint16_t buf_size;
 	uint16_t i;
 	struct rte_eth_rxmode *rx_conf = &dev->data->dev_conf.rxmode;
+	int rc;
 
 	PMD_INIT_FUNC_TRACE();
 	hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
@@ -3724,6 +4317,7 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 				       RTE_PKTMBUF_HEADROOM);
 		srrctl |= ((buf_size >> IXGBE_SRRCTL_BSIZEPKT_SHIFT) &
 			   IXGBE_SRRCTL_BSIZEPKT_MASK);
+
 		IXGBE_WRITE_REG(hw, IXGBE_SRRCTL(rxq->reg_idx), srrctl);
 
 		buf_size = (uint16_t) ((srrctl & IXGBE_SRRCTL_BSIZEPKT_MASK) <<
@@ -3738,8 +4332,6 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 	if (rx_conf->enable_scatter)
 		dev->data->scattered_rx = 1;
 
-	ixgbe_set_rx_function(dev);
-
 	/*
 	 * Device configured with multiple RX queues.
 	 */
@@ -3770,6 +4362,12 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
 		IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
 	}
 
+	rc = ixgbe_set_rsc(dev);
+	if (rc)
+		return rc;
+
+	ixgbe_set_rx_function(dev);
+
 	return 0;
 }
 
diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
index 3937cf6..120bbbd 100644
--- a/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
+++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx.h
@@ -79,6 +79,10 @@ struct ixgbe_rx_entry {
 	struct rte_mbuf *mbuf; /**< mbuf associated with RX descriptor. */
 };
 
+struct ixgbe_rsc_entry {
+	struct rte_mbuf *fbuf; /**< First segment of the fragmented packet. */
+};
+
 /**
  * Structure associated with each descriptor of the TX ring of a TX queue.
  */
@@ -105,6 +109,7 @@ struct ixgbe_rx_queue {
 	volatile uint32_t   *rdt_reg_addr; /**< RDT register address. */
 	volatile uint32_t   *rdh_reg_addr; /**< RDH register address. */
 	struct ixgbe_rx_entry *sw_ring; /**< address of RX software ring. */
+	struct ixgbe_rsc_entry *sw_rsc_ring; /**< address of RSC software ring. */
 	struct rte_mbuf *pkt_first_seg; /**< First segment of current packet. */
 	struct rte_mbuf *pkt_last_seg; /**< Last segment of current packet. */
 	uint64_t            mbuf_initializer; /**< value to init mbufs */
@@ -126,6 +131,7 @@ struct ixgbe_rx_queue {
 	uint8_t             port_id;  /**< Device port identifier. */
 	uint8_t             crc_len;  /**< 0 if CRC stripped, 4 otherwise. */
 	uint8_t             drop_en;  /**< If not 0, set SRRCTL.Drop_En. */
+	uint8_t             rsc_en;   /**< If not 0, RSC is enabled. */
 	uint8_t             rx_deferred_start; /**< not in global dev start. */
 #ifdef RTE_LIBRTE_IXGBE_RX_ALLOW_BULK_ALLOC
 	/** need to alloc dummy mbuf, for wraparound when scanning hw ring */
-- 
2.1.0

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2015-03-31 11:40 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-03-31 10:25 [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support Ananyev, Konstantin
2015-03-31 11:40 ` Vlad Zolotarov
  -- strict thread matches above, loose matches on Subject: below --
2015-03-18 17:52 [dpdk-dev] [PATCH v8 0/3]: Add LRO support to ixgbe PMD Vlad Zolotarov
2015-03-18 17:52 ` [dpdk-dev] [PATCH v8 3/3] ixgbe: Add LRO support Vlad Zolotarov
2015-03-30 14:18   ` Ananyev, Konstantin
2015-03-30 15:37     ` Vlad Zolotarov
2015-03-30 15:57       ` Vlad Zolotarov

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).