From: "Iremonger, Bernard" <bernard.iremonger@intel.com>
To: "Lu, Wenzhuo" <wenzhuo.lu@intel.com>, "dev@dpdk.org" <dev@dpdk.org>
Cc: "De Lara Guarch, Pablo" <pablo.de.lara.guarch@intel.com>,
"Lu, Wenzhuo" <wenzhuo.lu@intel.com>
Subject: Re: [dpdk-dev] [PATCH] app/testpmd: fix DCB config issue on ixgbe
Date: Wed, 24 Aug 2016 09:30:08 +0000 [thread overview]
Message-ID: <8CEF83825BEC744B83065625E567D7C21A06A32E@IRSMSX108.ger.corp.intel.com> (raw)
In-Reply-To: <1470374429-14848-1-git-send-email-wenzhuo.lu@intel.com>
Hi Wenzhuo,
> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Wenzhuo Lu
> Sent: Friday, August 5, 2016 6:20 AM
> To: dev@dpdk.org
> Cc: De Lara Guarch, Pablo <pablo.de.lara.guarch@intel.com>; Lu, Wenzhuo
> <wenzhuo.lu@intel.com>
> Subject: [dpdk-dev] [PATCH] app/testpmd: fix DCB config issue on ixgbe
>
> An issue is found that DCB cannot be configured on ixgbe NICs. It's said the
> TX queue number is not right.
> On ixgbe the max TX queue number is not fixed, it depends on the multi-
> queue mode.
>
> This patch adds the device configuration before getting info in the DCB
> configuration process. So the right info can be got depending on the
> configuration.
>
> Fixes: 96c0450dff86 (ixgbe: fix dropping packets from unsupported Tx
> queues)
> Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
> ---
> app/test-pmd/testpmd.c | 39 +++++++++++++++++++++------------------
> 1 file changed, 21 insertions(+), 18 deletions(-)
>
> diff --git a/app/test-pmd/testpmd.c b/app/test-pmd/testpmd.c index
> 1428974..ba41bea 100644
> --- a/app/test-pmd/testpmd.c
> +++ b/app/test-pmd/testpmd.c
> @@ -1962,17 +1962,30 @@ init_port_dcb_config(portid_t pid,
> uint8_t pfc_en)
> {
> struct rte_eth_conf port_conf;
> - struct rte_eth_dev_info dev_info;
> struct rte_port *rte_port;
> int retval;
> uint16_t i;
>
> - rte_eth_dev_info_get(pid, &dev_info);
> + rte_port = &ports[pid];
> +
> + memset(&port_conf, 0, sizeof(struct rte_eth_conf));
> + /* Enter DCB configuration status */
> + dcb_config = 1;
> +
> + /*set configuration of DCB in vt mode and DCB in non-vt mode*/
> + retval = get_eth_dcb_conf(&port_conf, dcb_mode, num_tcs,
> pfc_en);
> + if (retval < 0)
> + return retval;
> + port_conf.rxmode.hw_vlan_filter = 1;
> +
> + (void)rte_eth_dev_configure(pid, 0, 0, &port_conf);
The return value of rte_eth_dev_configure() should be checked.
Calling rte_eth_dev_configure() with parameters nb_rx_q and nb_tx_q equal to 0 returns -EINVAL, and does nothing.
Should the values of nb_rx_q and nb_tx_q be non zero?
> + rte_eth_dev_info_get(pid, &rte_port->dev_info);
>
> /* If dev_info.vmdq_pool_base is greater than 0,
> * the queue id of vmdq pools is started after pf queues.
> */
> - if (dcb_mode == DCB_VT_ENABLED && dev_info.vmdq_pool_base >
> 0) {
> + if (dcb_mode == DCB_VT_ENABLED &&
> + rte_port->dev_info.vmdq_pool_base > 0) {
> printf("VMDQ_DCB multi-queue mode is nonsensical"
> " for port %d.", pid);
> return -1;
> @@ -1982,13 +1995,13 @@ init_port_dcb_config(portid_t pid,
> * and has the same number of rxq and txq in dcb mode
> */
> if (dcb_mode == DCB_VT_ENABLED) {
> - nb_rxq = dev_info.max_rx_queues;
> - nb_txq = dev_info.max_tx_queues;
> + nb_rxq = rte_port->dev_info.max_rx_queues;
> + nb_txq = rte_port->dev_info.max_tx_queues;
> } else {
> /*if vt is disabled, use all pf queues */
> - if (dev_info.vmdq_pool_base == 0) {
> - nb_rxq = dev_info.max_rx_queues;
> - nb_txq = dev_info.max_tx_queues;
> + if (rte_port->dev_info.vmdq_pool_base == 0) {
> + nb_rxq = rte_port->dev_info.max_rx_queues;
> + nb_txq = rte_port->dev_info.max_tx_queues;
> } else {
> nb_rxq = (queueid_t)num_tcs;
> nb_txq = (queueid_t)num_tcs;
> @@ -1997,16 +2010,6 @@ init_port_dcb_config(portid_t pid,
> }
> rx_free_thresh = 64;
>
> - memset(&port_conf, 0, sizeof(struct rte_eth_conf));
> - /* Enter DCB configuration status */
> - dcb_config = 1;
> -
> - /*set configuration of DCB in vt mode and DCB in non-vt mode*/
> - retval = get_eth_dcb_conf(&port_conf, dcb_mode, num_tcs,
> pfc_en);
> - if (retval < 0)
> - return retval;
> -
> - rte_port = &ports[pid];
> memcpy(&rte_port->dev_conf, &port_conf, sizeof(struct
> rte_eth_conf));
>
> rxtx_port_config(rte_port);
> --
> 1.9.3
Regards,
Bernard.
next prev parent reply other threads:[~2016-08-24 9:30 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-08-05 5:20 Wenzhuo Lu
2016-08-24 9:30 ` Iremonger, Bernard [this message]
2016-08-24 15:21 ` Iremonger, Bernard
2016-08-25 1:38 ` Lu, Wenzhuo
2016-08-25 8:39 ` Iremonger, Bernard
2016-08-26 1:41 ` Lu, Wenzhuo
2016-08-26 10:04 ` Iremonger, Bernard
2016-08-29 2:42 ` Lu, Wenzhuo
2016-09-23 18:24 ` Thomas Monjalon
2016-09-26 0:42 ` Lu, Wenzhuo
2016-09-26 1:11 ` [dpdk-dev] [PATCH v2] app/testpmd: fix DCB config issue Wenzhuo Lu
2016-10-05 10:02 ` Iremonger, Bernard
2016-10-13 15:14 ` Thomas Monjalon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=8CEF83825BEC744B83065625E567D7C21A06A32E@IRSMSX108.ger.corp.intel.com \
--to=bernard.iremonger@intel.com \
--cc=dev@dpdk.org \
--cc=pablo.de.lara.guarch@intel.com \
--cc=wenzhuo.lu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).