* [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close @ 2019-07-08 11:43 Xiao Zhang 2019-07-08 8:35 ` Zhao1, Wei 0 siblings, 1 reply; 3+ messages in thread From: Xiao Zhang @ 2019-07-08 11:43 UTC (permalink / raw) To: dev; +Cc: Xiao Zhang Unit hang may occur if multiple descriptors are available in the rings during reset or close. This state can be detected by configure status by bit 8 in register. If the bit is set and there are pending descriptors in one of the rings, we must flush them before reset or close. Signed-off-by: Xiao Zhang <xiao.zhang@intel.com> --- drivers/net/e1000/base/e1000_ich8lan.h | 1 + drivers/net/e1000/e1000_ethdev.h | 1 + drivers/net/e1000/igb_ethdev.c | 4 ++ drivers/net/e1000/igb_rxtx.c | 96 ++++++++++++++++++++++++++++++++++ 4 files changed, 102 insertions(+) diff --git a/drivers/net/e1000/base/e1000_ich8lan.h b/drivers/net/e1000/base/e1000_ich8lan.h index bc4ed1d..1f2a3f8 100644 --- a/drivers/net/e1000/base/e1000_ich8lan.h +++ b/drivers/net/e1000/base/e1000_ich8lan.h @@ -120,6 +120,7 @@ POSSIBILITY OF SUCH DAMAGE. #define E1000_FEXTNVM7_SIDE_CLK_UNGATE 0x00000004 #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT) #define E1000_FEXTNVM7_DISABLE_SMB_PERST 0x00000020 +#define E1000_FEXTNVM7_NEED_DESCRING_FLUSH 0x00000100 #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */ #define E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS 0x00000800 #define E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS 0x00001000 diff --git a/drivers/net/e1000/e1000_ethdev.h b/drivers/net/e1000/e1000_ethdev.h index 67acb73..3451979 100644 --- a/drivers/net/e1000/e1000_ethdev.h +++ b/drivers/net/e1000/e1000_ethdev.h @@ -522,5 +522,6 @@ int igb_action_rss_same(const struct rte_flow_action_rss *comp, int igb_config_rss_filter(struct rte_eth_dev *dev, struct igb_rte_flow_rss_conf *conf, bool add); +void igb_flush_desc_rings(struct rte_eth_dev *dev); #endif /* _E1000_ETHDEV_H_ */ diff --git a/drivers/net/e1000/igb_ethdev.c b/drivers/net/e1000/igb_ethdev.c index 3ee28cf..845101b 100644 --- a/drivers/net/e1000/igb_ethdev.c +++ b/drivers/net/e1000/igb_ethdev.c @@ -1589,6 +1589,10 @@ eth_igb_close(struct rte_eth_dev *dev) eth_igb_stop(dev); adapter->stopped = 1; + /* Flush desc rings for i219 */ + if (hw->mac.type >= e1000_pch_spt) + igb_flush_desc_rings(dev); + e1000_phy_hw_reset(hw); igb_release_manageability(hw); igb_hw_control_release(hw); diff --git a/drivers/net/e1000/igb_rxtx.c b/drivers/net/e1000/igb_rxtx.c index c5606de..33eeb4e 100644 --- a/drivers/net/e1000/igb_rxtx.c +++ b/drivers/net/e1000/igb_rxtx.c @@ -18,6 +18,7 @@ #include <rte_log.h> #include <rte_debug.h> #include <rte_pci.h> +#include <rte_bus_pci.h> #include <rte_memory.h> #include <rte_memcpy.h> #include <rte_memzone.h> @@ -63,6 +64,9 @@ #define IGB_TX_OFFLOAD_NOTSUP_MASK \ (PKT_TX_OFFLOAD_MASK ^ IGB_TX_OFFLOAD_MASK) +/* PCI offset for querying descriptor ring status*/ +#define PCICFG_DESC_RING_STATUS 0xE4 + /** * Structure associated with each descriptor of the RX ring of a RX queue. */ @@ -2962,3 +2966,95 @@ igb_config_rss_filter(struct rte_eth_dev *dev, return 0; } + +static void e1000_flush_tx_ring(struct rte_eth_dev *dev) +{ + struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data->dev_private); + volatile union e1000_adv_tx_desc *tx_desc; + uint32_t tdt, tctl, txd_lower = E1000_TXD_CMD_IFCS; + uint16_t size = 512; + struct igb_tx_queue *txq; + + if (dev->data->tx_queues == NULL) + return; + txq = dev->data->tx_queues[0]; + + tctl = E1000_READ_REG(hw, E1000_TCTL); + E1000_WRITE_REG(hw, E1000_TCTL, tctl | E1000_TCTL_EN); + tdt = E1000_READ_REG(hw, E1000_TDT(0)); + if (tdt != txq->tx_tail) + return; + tx_desc = txq->tx_ring; + tx_desc->read.buffer_addr = txq->tx_ring_phys_addr; + tx_desc->read.cmd_type_len = rte_cpu_to_le_32(txd_lower | size); + tx_desc->read.olinfo_status = 0; + + rte_wmb(); + txq->tx_tail++; + if (txq->tx_tail == txq->nb_tx_desc) + txq->tx_tail = 0; + rte_io_wmb(); + E1000_WRITE_REG(hw, E1000_TDT(0), txq->tx_tail); + usec_delay(250); +} + +static void e1000_flush_rx_ring(struct rte_eth_dev *dev) +{ + uint32_t rctl, rxdctl; + struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data->dev_private); + + rctl = E1000_READ_REG(hw, E1000_RCTL); + E1000_WRITE_REG(hw, E1000_TCTL, rctl & ~E1000_RCTL_EN); + E1000_WRITE_FLUSH(hw); + usec_delay(150); + + rxdctl = E1000_READ_REG(hw, E1000_RXDCTL(0)); + /* zero the lower 14 bits (prefetch and host thresholds) */ + rxdctl &= 0xffffc000; + + /* update thresholds: prefetch threshold to 31, host threshold to 1 + * and make sure the granularity is "descriptors" and not "cache lines" + */ + rxdctl |= (0x1F | (1UL << 8) | E1000_RXDCTL_THRESH_UNIT_DESC); + + E1000_WRITE_REG(hw, E1000_RXDCTL(0), rxdctl); + /* momentarily enable the RX ring for the changes to take effect */ + E1000_WRITE_REG(hw, E1000_RCTL, rctl | E1000_RCTL_EN); + E1000_WRITE_FLUSH(hw); + usec_delay(150); + E1000_WRITE_REG(hw, E1000_RCTL, rctl & ~E1000_RCTL_EN); +} + +/** + * igb_flush_desc_rings - remove all descriptors from the descriptor rings + * + * In i219, the descriptor rings must be emptied before resetting/closing the + * HW. Failure to do this will cause the HW to enter a unit hang state which + * can only be released by PCI reset on the device + * + */ + +void igb_flush_desc_rings(struct rte_eth_dev *dev) +{ + uint32_t fextnvm11, tdlen; + struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data->dev_private); + struct rte_pci_device *pci_dev = RTE_ETH_DEV_TO_PCI(dev); + uint32_t hang_state = 0; + + fextnvm11 = E1000_READ_REG(hw, E1000_FEXTNVM11); + E1000_WRITE_REG(hw, E1000_FEXTNVM11, + fextnvm11 | E1000_FEXTNVM11_DISABLE_MULR_FIX); + tdlen = E1000_READ_REG(hw, E1000_TDLEN(0)); + rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state), + PCICFG_DESC_RING_STATUS); + + /* do nothing if we're not in faulty state, or if the queue is empty */ + if ((hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) && tdlen) { + /* flush desc ring */ + e1000_flush_tx_ring(dev); + rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state), + PCICFG_DESC_RING_STATUS); + if (hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) + e1000_flush_rx_ring(dev); + } +} -- 2.7.4 ^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close 2019-07-08 11:43 [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close Xiao Zhang @ 2019-07-08 8:35 ` Zhao1, Wei 2019-07-09 2:46 ` Zhang, Xiao 0 siblings, 1 reply; 3+ messages in thread From: Zhao1, Wei @ 2019-07-08 8:35 UTC (permalink / raw) To: Zhang, Xiao, dev; +Cc: Zhang, Xiao Hi, xiao > -----Original Message----- > From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Xiao Zhang > Sent: Monday, July 8, 2019 7:44 PM > To: dev@dpdk.org > Cc: Zhang, Xiao <xiao.zhang@intel.com> > Subject: [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close > > Unit hang may occur if multiple descriptors are available in the rings during > reset or close. This state can be detected by configure status by bit 8 in register. > If the bit is set and there are pending descriptors in one of the rings, we must > flush them before reset or close. > > Signed-off-by: Xiao Zhang <xiao.zhang@intel.com> > --- > drivers/net/e1000/base/e1000_ich8lan.h | 1 + > drivers/net/e1000/e1000_ethdev.h | 1 + > drivers/net/e1000/igb_ethdev.c | 4 ++ > drivers/net/e1000/igb_rxtx.c | 96 > ++++++++++++++++++++++++++++++++++ > 4 files changed, 102 insertions(+) > > diff --git a/drivers/net/e1000/base/e1000_ich8lan.h > b/drivers/net/e1000/base/e1000_ich8lan.h > index bc4ed1d..1f2a3f8 100644 > --- a/drivers/net/e1000/base/e1000_ich8lan.h > +++ b/drivers/net/e1000/base/e1000_ich8lan.h > @@ -120,6 +120,7 @@ POSSIBILITY OF SUCH DAMAGE. > #define E1000_FEXTNVM7_SIDE_CLK_UNGATE 0x00000004 > #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT) > #define E1000_FEXTNVM7_DISABLE_SMB_PERST 0x00000020 > +#define E1000_FEXTNVM7_NEED_DESCRING_FLUSH 0x00000100 > #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */ > #define E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS 0x00000800 > #define E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS 0x00001000 > diff --git a/drivers/net/e1000/e1000_ethdev.h > b/drivers/net/e1000/e1000_ethdev.h > index 67acb73..3451979 100644 > --- a/drivers/net/e1000/e1000_ethdev.h > +++ b/drivers/net/e1000/e1000_ethdev.h > @@ -522,5 +522,6 @@ int igb_action_rss_same(const struct > rte_flow_action_rss *comp, int igb_config_rss_filter(struct rte_eth_dev *dev, > struct igb_rte_flow_rss_conf *conf, > bool add); > +void igb_flush_desc_rings(struct rte_eth_dev *dev); > > #endif /* _E1000_ETHDEV_H_ */ > diff --git a/drivers/net/e1000/igb_ethdev.c b/drivers/net/e1000/igb_ethdev.c > index 3ee28cf..845101b 100644 > --- a/drivers/net/e1000/igb_ethdev.c > +++ b/drivers/net/e1000/igb_ethdev.c > @@ -1589,6 +1589,10 @@ eth_igb_close(struct rte_eth_dev *dev) > eth_igb_stop(dev); > adapter->stopped = 1; > > + /* Flush desc rings for i219 */ > + if (hw->mac.type >= e1000_pch_spt) > + igb_flush_desc_rings(dev); > + > e1000_phy_hw_reset(hw); > igb_release_manageability(hw); > igb_hw_control_release(hw); > diff --git a/drivers/net/e1000/igb_rxtx.c b/drivers/net/e1000/igb_rxtx.c index > c5606de..33eeb4e 100644 > --- a/drivers/net/e1000/igb_rxtx.c > +++ b/drivers/net/e1000/igb_rxtx.c > @@ -18,6 +18,7 @@ > #include <rte_log.h> > #include <rte_debug.h> > #include <rte_pci.h> > +#include <rte_bus_pci.h> > #include <rte_memory.h> > #include <rte_memcpy.h> > #include <rte_memzone.h> > @@ -63,6 +64,9 @@ > #define IGB_TX_OFFLOAD_NOTSUP_MASK \ > (PKT_TX_OFFLOAD_MASK ^ IGB_TX_OFFLOAD_MASK) > > +/* PCI offset for querying descriptor ring status*/ > +#define PCICFG_DESC_RING_STATUS 0xE4 > + > /** > * Structure associated with each descriptor of the RX ring of a RX queue. > */ > @@ -2962,3 +2966,95 @@ igb_config_rss_filter(struct rte_eth_dev *dev, > > return 0; > } > + > +static void e1000_flush_tx_ring(struct rte_eth_dev *dev) { > + struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data- > >dev_private); > + volatile union e1000_adv_tx_desc *tx_desc; > + uint32_t tdt, tctl, txd_lower = E1000_TXD_CMD_IFCS; > + uint16_t size = 512; > + struct igb_tx_queue *txq; > + > + if (dev->data->tx_queues == NULL) > + return; > + txq = dev->data->tx_queues[0]; > + > + tctl = E1000_READ_REG(hw, E1000_TCTL); > + E1000_WRITE_REG(hw, E1000_TCTL, tctl | E1000_TCTL_EN); > + tdt = E1000_READ_REG(hw, E1000_TDT(0)); > + if (tdt != txq->tx_tail) > + return; > + tx_desc = txq->tx_ring; > + tx_desc->read.buffer_addr = txq->tx_ring_phys_addr; > + tx_desc->read.cmd_type_len = rte_cpu_to_le_32(txd_lower | size); > + tx_desc->read.olinfo_status = 0; > + > + rte_wmb(); > + txq->tx_tail++; > + if (txq->tx_tail == txq->nb_tx_desc) > + txq->tx_tail = 0; > + rte_io_wmb(); > + E1000_WRITE_REG(hw, E1000_TDT(0), txq->tx_tail); > + usec_delay(250); > +} > + > +static void e1000_flush_rx_ring(struct rte_eth_dev *dev) { > + uint32_t rctl, rxdctl; > + struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data- > >dev_private); > + > + rctl = E1000_READ_REG(hw, E1000_RCTL); > + E1000_WRITE_REG(hw, E1000_TCTL, rctl & ~E1000_RCTL_EN); > + E1000_WRITE_FLUSH(hw); > + usec_delay(150); > + > + rxdctl = E1000_READ_REG(hw, E1000_RXDCTL(0)); > + /* zero the lower 14 bits (prefetch and host thresholds) */ > + rxdctl &= 0xffffc000; > + > + /* update thresholds: prefetch threshold to 31, host threshold to 1 > + * and make sure the granularity is "descriptors" and not "cache lines" > + */ > + rxdctl |= (0x1F | (1UL << 8) | E1000_RXDCTL_THRESH_UNIT_DESC); > + > + E1000_WRITE_REG(hw, E1000_RXDCTL(0), rxdctl); > + /* momentarily enable the RX ring for the changes to take effect */ > + E1000_WRITE_REG(hw, E1000_RCTL, rctl | E1000_RCTL_EN); > + E1000_WRITE_FLUSH(hw); > + usec_delay(150); > + E1000_WRITE_REG(hw, E1000_RCTL, rctl & ~E1000_RCTL_EN); } > + In dpdk driver, it may enable and use many queues, so why do we only Process tx and rx queue 0, ring for other queues not need to handle? > +/** > + * igb_flush_desc_rings - remove all descriptors from the descriptor > +rings > + * > + * In i219, the descriptor rings must be emptied before > +resetting/closing the > + * HW. Failure to do this will cause the HW to enter a unit hang state > +which > + * can only be released by PCI reset on the device > + * > + */ > + > +void igb_flush_desc_rings(struct rte_eth_dev *dev) { > + uint32_t fextnvm11, tdlen; > + struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data- > >dev_private); > + struct rte_pci_device *pci_dev = RTE_ETH_DEV_TO_PCI(dev); > + uint32_t hang_state = 0; > + > + fextnvm11 = E1000_READ_REG(hw, E1000_FEXTNVM11); > + E1000_WRITE_REG(hw, E1000_FEXTNVM11, > + fextnvm11 | E1000_FEXTNVM11_DISABLE_MULR_FIX); > + tdlen = E1000_READ_REG(hw, E1000_TDLEN(0)); > + rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state), > + PCICFG_DESC_RING_STATUS); > + > + /* do nothing if we're not in faulty state, or if the queue is empty */ > + if ((hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) && > tdlen) { > + /* flush desc ring */ > + e1000_flush_tx_ring(dev); > + rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state), > + PCICFG_DESC_RING_STATUS); > + if (hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) > + e1000_flush_rx_ring(dev); > + } > +} > -- > 2.7.4 ^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close 2019-07-08 8:35 ` Zhao1, Wei @ 2019-07-09 2:46 ` Zhang, Xiao 0 siblings, 0 replies; 3+ messages in thread From: Zhang, Xiao @ 2019-07-09 2:46 UTC (permalink / raw) To: Zhao1, Wei, dev Hi Wei, Thanks for your point. I219 supports dual rx and tx queues, I will update the fix. BR, Xiao > -----Original Message----- > From: Zhao1, Wei > Sent: Monday, July 8, 2019 4:36 PM > To: Zhang, Xiao <xiao.zhang@intel.com>; dev@dpdk.org > Cc: Zhang, Xiao <xiao.zhang@intel.com> > Subject: RE: [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close > > Hi, xiao > > > -----Original Message----- > > From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Xiao Zhang > > Sent: Monday, July 8, 2019 7:44 PM > > To: dev@dpdk.org > > Cc: Zhang, Xiao <xiao.zhang@intel.com> > > Subject: [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on > > reset/close > > > > Unit hang may occur if multiple descriptors are available in the rings > > during reset or close. This state can be detected by configure status by bit 8 in > register. > > If the bit is set and there are pending descriptors in one of the > > rings, we must flush them before reset or close. > > > > Signed-off-by: Xiao Zhang <xiao.zhang@intel.com> > > --- > > drivers/net/e1000/base/e1000_ich8lan.h | 1 + > > drivers/net/e1000/e1000_ethdev.h | 1 + > > drivers/net/e1000/igb_ethdev.c | 4 ++ > > drivers/net/e1000/igb_rxtx.c | 96 > > ++++++++++++++++++++++++++++++++++ > > 4 files changed, 102 insertions(+) > > > > diff --git a/drivers/net/e1000/base/e1000_ich8lan.h > > b/drivers/net/e1000/base/e1000_ich8lan.h > > index bc4ed1d..1f2a3f8 100644 > > --- a/drivers/net/e1000/base/e1000_ich8lan.h > > +++ b/drivers/net/e1000/base/e1000_ich8lan.h > > @@ -120,6 +120,7 @@ POSSIBILITY OF SUCH DAMAGE. > > #define E1000_FEXTNVM7_SIDE_CLK_UNGATE 0x00000004 > > #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT) > > #define E1000_FEXTNVM7_DISABLE_SMB_PERST 0x00000020 > > +#define E1000_FEXTNVM7_NEED_DESCRING_FLUSH 0x00000100 > > #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */ > > #define E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS 0x00000800 > > #define E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS 0x00001000 > > diff --git a/drivers/net/e1000/e1000_ethdev.h > > b/drivers/net/e1000/e1000_ethdev.h > > index 67acb73..3451979 100644 > > --- a/drivers/net/e1000/e1000_ethdev.h > > +++ b/drivers/net/e1000/e1000_ethdev.h > > @@ -522,5 +522,6 @@ int igb_action_rss_same(const struct > > rte_flow_action_rss *comp, int igb_config_rss_filter(struct rte_eth_dev *dev, > > struct igb_rte_flow_rss_conf *conf, > > bool add); > > +void igb_flush_desc_rings(struct rte_eth_dev *dev); > > > > #endif /* _E1000_ETHDEV_H_ */ > > diff --git a/drivers/net/e1000/igb_ethdev.c > > b/drivers/net/e1000/igb_ethdev.c index 3ee28cf..845101b 100644 > > --- a/drivers/net/e1000/igb_ethdev.c > > +++ b/drivers/net/e1000/igb_ethdev.c > > @@ -1589,6 +1589,10 @@ eth_igb_close(struct rte_eth_dev *dev) > > eth_igb_stop(dev); > > adapter->stopped = 1; > > > > + /* Flush desc rings for i219 */ > > + if (hw->mac.type >= e1000_pch_spt) > > + igb_flush_desc_rings(dev); > > + > > e1000_phy_hw_reset(hw); > > igb_release_manageability(hw); > > igb_hw_control_release(hw); > > diff --git a/drivers/net/e1000/igb_rxtx.c > > b/drivers/net/e1000/igb_rxtx.c index c5606de..33eeb4e 100644 > > --- a/drivers/net/e1000/igb_rxtx.c > > +++ b/drivers/net/e1000/igb_rxtx.c > > @@ -18,6 +18,7 @@ > > #include <rte_log.h> > > #include <rte_debug.h> > > #include <rte_pci.h> > > +#include <rte_bus_pci.h> > > #include <rte_memory.h> > > #include <rte_memcpy.h> > > #include <rte_memzone.h> > > @@ -63,6 +64,9 @@ > > #define IGB_TX_OFFLOAD_NOTSUP_MASK \ > > (PKT_TX_OFFLOAD_MASK ^ IGB_TX_OFFLOAD_MASK) > > > > +/* PCI offset for querying descriptor ring status*/ > > +#define PCICFG_DESC_RING_STATUS 0xE4 > > + > > /** > > * Structure associated with each descriptor of the RX ring of a RX queue. > > */ > > @@ -2962,3 +2966,95 @@ igb_config_rss_filter(struct rte_eth_dev *dev, > > > > return 0; > > } > > + > > +static void e1000_flush_tx_ring(struct rte_eth_dev *dev) { > > + struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data- > > >dev_private); > > + volatile union e1000_adv_tx_desc *tx_desc; > > + uint32_t tdt, tctl, txd_lower = E1000_TXD_CMD_IFCS; > > + uint16_t size = 512; > > + struct igb_tx_queue *txq; > > + > > + if (dev->data->tx_queues == NULL) > > + return; > > + txq = dev->data->tx_queues[0]; > > + > > + tctl = E1000_READ_REG(hw, E1000_TCTL); > > + E1000_WRITE_REG(hw, E1000_TCTL, tctl | E1000_TCTL_EN); > > + tdt = E1000_READ_REG(hw, E1000_TDT(0)); > > + if (tdt != txq->tx_tail) > > + return; > > + tx_desc = txq->tx_ring; > > + tx_desc->read.buffer_addr = txq->tx_ring_phys_addr; > > + tx_desc->read.cmd_type_len = rte_cpu_to_le_32(txd_lower | size); > > + tx_desc->read.olinfo_status = 0; > > + > > + rte_wmb(); > > + txq->tx_tail++; > > + if (txq->tx_tail == txq->nb_tx_desc) > > + txq->tx_tail = 0; > > + rte_io_wmb(); > > + E1000_WRITE_REG(hw, E1000_TDT(0), txq->tx_tail); > > + usec_delay(250); > > +} > > + > > +static void e1000_flush_rx_ring(struct rte_eth_dev *dev) { > > + uint32_t rctl, rxdctl; > > + struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data- > > >dev_private); > > + > > + rctl = E1000_READ_REG(hw, E1000_RCTL); > > + E1000_WRITE_REG(hw, E1000_TCTL, rctl & ~E1000_RCTL_EN); > > + E1000_WRITE_FLUSH(hw); > > + usec_delay(150); > > + > > + rxdctl = E1000_READ_REG(hw, E1000_RXDCTL(0)); > > + /* zero the lower 14 bits (prefetch and host thresholds) */ > > + rxdctl &= 0xffffc000; > > + > > + /* update thresholds: prefetch threshold to 31, host threshold to 1 > > + * and make sure the granularity is "descriptors" and not "cache lines" > > + */ > > + rxdctl |= (0x1F | (1UL << 8) | E1000_RXDCTL_THRESH_UNIT_DESC); > > + > > + E1000_WRITE_REG(hw, E1000_RXDCTL(0), rxdctl); > > + /* momentarily enable the RX ring for the changes to take effect */ > > + E1000_WRITE_REG(hw, E1000_RCTL, rctl | E1000_RCTL_EN); > > + E1000_WRITE_FLUSH(hw); > > + usec_delay(150); > > + E1000_WRITE_REG(hw, E1000_RCTL, rctl & ~E1000_RCTL_EN); } > > + > > In dpdk driver, it may enable and use many queues, so why do we only Process tx > and rx queue 0, ring for other queues not need to handle? > > > > > > > > +/** > > + * igb_flush_desc_rings - remove all descriptors from the descriptor > > +rings > > + * > > + * In i219, the descriptor rings must be emptied before > > +resetting/closing the > > + * HW. Failure to do this will cause the HW to enter a unit hang state > > +which > > + * can only be released by PCI reset on the device > > + * > > + */ > > + > > +void igb_flush_desc_rings(struct rte_eth_dev *dev) { > > + uint32_t fextnvm11, tdlen; > > + struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data- > > >dev_private); > > + struct rte_pci_device *pci_dev = RTE_ETH_DEV_TO_PCI(dev); > > + uint32_t hang_state = 0; > > + > > + fextnvm11 = E1000_READ_REG(hw, E1000_FEXTNVM11); > > + E1000_WRITE_REG(hw, E1000_FEXTNVM11, > > + fextnvm11 | E1000_FEXTNVM11_DISABLE_MULR_FIX); > > + tdlen = E1000_READ_REG(hw, E1000_TDLEN(0)); > > + rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state), > > + PCICFG_DESC_RING_STATUS); > > + > > + /* do nothing if we're not in faulty state, or if the queue is empty */ > > + if ((hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) && > > tdlen) { > > + /* flush desc ring */ > > + e1000_flush_tx_ring(dev); > > + rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state), > > + PCICFG_DESC_RING_STATUS); > > + if (hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) > > + e1000_flush_rx_ring(dev); > > + } > > +} > > -- > > 2.7.4 ^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-07-09 2:46 UTC | newest] Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-07-08 11:43 [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close Xiao Zhang 2019-07-08 8:35 ` Zhao1, Wei 2019-07-09 2:46 ` Zhang, Xiao
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).