[dts] [PATCH V2] add test plan interrupt_pmd

[dts] [PATCH V2] add test plan interrupt_pmd

[xu,gang]

Signed-off-by: xu,gang <gangx.xu@intel.com>
---
 test_plans/interrupt_pmd_test_plan.rst | 262 +++++++++++++++++++++++++++++++++
 1 file changed, 262 insertions(+)
 create mode 100644 test_plans/interrupt_pmd_test_plan.rst

diff --git a/test_plans/interrupt_pmd_test_plan.rst b/test_plans/interrupt_pmd_test_plan.rst
new file mode 100644
index 0000000..6d4c7c5
--- /dev/null
+++ b/test_plans/interrupt_pmd_test_plan.rst
@@ -0,0 +1,262 @@
+.. Copyright (c) <2017>, Intel Corporation
+   All rights reserved.
+
+   Redistribution and use in source and binary forms, with or without
+   modification, are permitted provided that the following conditions
+   are met:
+
+   - Redistributions of source code must retain the above copyright
+     notice, this list of conditions and the following disclaimer.
+
+   - Redistributions in binary form must reproduce the above copyright
+     notice, this list of conditions and the following disclaimer in
+     the documentation and/or other materials provided with the
+     distribution.
+
+   - Neither the name of Intel Corporation nor the names of its
+     contributors may be used to endorse or promote products derived
+     from this software without specific prior written permission.
+
+   THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+   "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+   LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+   FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+   COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+   INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+   (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+   SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+   HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+   STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+   ARISING IN ANY WAY OUT OF THE USE OF TH
+
+=====================
+One-shot Rx Interrupt 
+=====================
+One-shot Rx interrupt feature will split rx interrupt handling from other 
+interrupts like LSC interrupt. It implemented one handling mechanism to 
+eliminate non-deterministic DPDK polling thread wakeup latency.
+
+VFIO' multiple interrupt vectors support mechanism to enable multiple event fds
+serving per Rx queue interrupt handling.
+UIO has limited interrupt support, specifically it only support a single 
+interrupt vector, which is not suitable for enabling multi queues Rx/Tx 
+interrupt.
+
+Prerequisites
+=============
+Each of the 10Gb Ethernet* ports of the DUT is directly connected in
+full-duplex to a different port of the peer traffic generator.
+
+Assume PF port PCI addresses are 0000:08:00.0 and 0000:08:00.1,
+ their Interfaces name are p786p1 and p786p2.
+Assume generated VF PCI address will be 0000:08:10.0, 0000:08:10.1.
+
+Iommu pass through feature has been enabled in kernel.
+	intel_iommu=on iommu=pt
+
+Support igb_uio and vfio driver, if used vfio, kernel need 3.6+ and enable vt-d
+in bios. When used vfio, requested to insmod two drivers vfio and vfio-pci.
+	
+Test Case1: PF interrupt pmd with uio
+=====================================
+Run l3fwd-power with one queue per port::
+	l3fwd-power -c 7 -n 4 -- -p 0x3 -P --config="(0,0,1),(1,0,2)"
+
+Send one packet to Port0 and Port1, check that thread on core1 and core2 
+waked up:
+	L3FWD_POWER: lcore 1 is waked up from rx interrupt on port1,rxq0
+	L3FWD_POWER: lcore 2 is waked up from rx interrupt on port1,rxq0
+	
+Check the packet has been normally forwarded.
+
+After the packet forwarded, thread on core1 and core 2 will return to sleep.
+	L3FWD_POWER: lcore 1 sleeps until interrupt on port0,rxq0 triggers
+	L3FWD_POWER: lcore 2 sleeps until interrupt on port0,rxq0 triggers
+
+Send packet flows to Port0 and Port1, check that thread on core1 and core2 will
+keep up awake.	
+
+Test Case2: PF interrupt pmd with vfio
+======================================
+Run l3fwd-power with one queue per port::
+	l3fwd-power -c 7 -n 4 -- -p 0x3 -P --config="(0,0,1),(1,0,2)"
+
+Send one packet to Port0 and Port1, check that thread on core1 and core2 
+waked up:
+	L3FWD_POWER: lcore 1 is waked up from rx interrupt on port1,rxq0
+	L3FWD_POWER: lcore 2 is waked up from rx interrupt on port1,rxq0
+	
+Check the packet has been normally forwarded.
+
+After the packet forwarded, thread on core1 and core 2 will return to sleep.
+	L3FWD_POWER: lcore 1 sleeps until interrupt on port0,rxq0 triggers
+	L3FWD_POWER: lcore 2 sleeps until interrupt on port0,rxq0 triggers
+
+Send packet flows to Port0 and Port1, check that thread on core1 and core2 will
+keep up awake.	
+
+Test Case3: PF interrupt pmd multi queue with vfio
+==================================================
+Run l3fwd-power with two queues per port::
+	l3fwd-power -c 1f -n 4 -- -p 0x3 \
+		--config="(0,0,1),(0,1,2)(1,0,3),(1,1,4)"
+
+Send packet with increased dest IP to Port0 and Port1, check that thread on 
+core1,core2,core3,core4 waked up:
+	L3FWD_POWER: lcore 1 is waked up from rx interrupt on port1,rxq0
+	L3FWD_POWER: lcore 2 is waked up from rx interrupt on port1,rxq1
+	L3FWD_POWER: lcore 3 is waked up from rx interrupt on port1,rxq0
+	L3FWD_POWER: lcore 4 is waked up from rx interrupt on port1,rxq1
+	
+Check the packet has been normally forwarded.
+
+After the packet forwarded, thread on core1,core2,core3,core4 will return to 
+sleep.
+	L3FWD_POWER: lcore 1 sleeps until interrupt on port0,rxq0 triggers
+	L3FWD_POWER: lcore 2 sleeps until interrupt on port0,rxq1 triggers
+	L3FWD_POWER: lcore 3 sleeps until interrupt on port1,rxq0 triggers
+	L3FWD_POWER: lcore 4 sleeps until interrupt on port1,rxq1 triggers
+
+Send packet flows to Port0 and Port1, check that thread on core1,core2,core3,
+core4 will keep up awake.
+
+Test Case4: PF lsc interrupt with vfio
+======================================
+Run l3fwd-power with one queue per port::
+	l3fwd-power -c 7 -n 4 -- -p 0x3 -P --config="(0,0,1),(1,0,2)"
+
+Plug out Port0 cable, check that link down interrtup captured and handled by 
+pmd driver.
+
+Plug out Port1 cable, check that link down interrtup captured and handled by 
+pmd driver.
+
+Plug in Port0 cable, check that link up interrtup captured and handled by pmd 
+driver.
+
+Plug in Port1 cable, check that link up interrtup captured and handled by pmd 
+driver.
+
+Test Case5: PF interrupt max Rx queues with vfio
+================================================
+Run l3fwd-power with 32 queues per port::
+	l3fwd-power -c ffffffff -n 4 -- -p 0x3 -P --config="(0,0,0),(0,1,1),\
+			(0,2,2),(0,3,3),(0,4,4),(0,5,5),(0,6,6),(0,7,7),(0,8,8),
+			(0,9,9),(0,10,10),(0,11,11),(0,12,12),(0,13,13),(0,14,14),\
+			(0,15,15),\
+			(1,0,16),(1,1,17),(1,2,18),(1,3,19),(1,4,20),(1,5,21),(1,6,22),\
+			(1,7,23),(1,8,24),(1,9,25),(1,10,26),(1,11,27),(1,12,28),\
+			(1,13,29),(1,14,30),\(1,15,31)"
+
+Send packet with increased dest IP to Port0, check that all threads waked up:
+
+Test Case6: VF interrupt pmd in VM with uio
+===========================================
+Create one VF per Port in host and add these two VFs into VM:
+	rmmod ixgbe
+	modprobe ixgbe max_vfs=1
+	virsh
+	virsh # nodedev-dettach PCI_VF1
+	virsh # nodedev-dettach PCI_VF2
+	
+Assign mac address for VF:
+	ip link set p786p1 vf 0 mac 00:11:22:33:44:55
+	ip link set p786p2 vf 0 mac 00:11:22:33:44:66
+
+Start VM and start l3fwd-power with one queue per port in VM:
+	l3fwd-power -c 7 -n 4 -- -p 0x3 -P --config="(0,0,1),(1,0,2)"
+
+Send one packet to VF0 and VF1, check that thread on core1 and core2 waked up:
+	L3FWD_POWER: lcore 1 is waked up from rx interrupt on port1,rxq0
+	L3FWD_POWER: lcore 2 is waked up from rx interrupt on port1,rxq0
+	
+Check the packet has been normally forwarded.
+
+After the packet forwarded, thread on core1 and core 2 will return to sleep.
+	L3FWD_POWER: lcore 1 sleeps until interrupt on port0,rxq0 triggers
+	L3FWD_POWER: lcore 2 sleeps until interrupt on port0,rxq0 triggers
+
+Send packet flows to VF0 and VF1, check that thread on core1 and core2 will 
+keep up awake.
+
+Test Case7: VF interrupt pmd in Host with uio
+=============================================
+Create one VF per Port in host and make sure PF interface up:
+	rmmod ixgbe
+	modprobe ixgbe max_vfs=1
+	ifconfig p786p1 up
+	ifconfig p786p2 up
+	
+Assign mac address for VF:
+	ip link set p786p1 vf 0 mac 00:11:22:33:44:55
+	ip link set p786p2 vf 0 mac 00:11:22:33:44:66
+
+Bind VF device to igb_uio:
+	./usertools/dpdk-devbind.py --bind=igb_uio 0000:08:10.0 0000:08:10.1
+	
+Start VM and start l3fwd-power with one queue per port in VM:
+	l3fwd-power -c 7 -n 4 -- -p 0x3 -P --config="(0,0,1),(1,0,2)"
+
+Send one packet to VF0 and VF1, check that thread on core1 and core2 waked up:
+	L3FWD_POWER: lcore 1 is waked up from rx interrupt on port1,rxq0
+	L3FWD_POWER: lcore 2 is waked up from rx interrupt on port1,rxq0
+	
+Check the packet has been normally forwarded.
+
+After the packet forwarded, thread on core1 and core 2 will return to sleep.
+	L3FWD_POWER: lcore 1 sleeps until interrupt on port0,rxq0 triggers
+	L3FWD_POWER: lcore 2 sleeps until interrupt on port0,rxq0 triggers
+
+Send packet flows to VF0 and VF1, check that thread on core1 and core2 will 
+keep up awake.
+
+Test Case8: VF interrupt pmd in Host with vfio
+==============================================
+Create one VF per Port in host and make sure PF interface up:
+	rmmod ixgbe
+	modprobe ixgbe max_vfs=2
+	ifconfig p786p1 up
+	ifconfig p786p2 up
+	
+Assign mac address for VF:
+	ip link set p786p1 vf 0 mac 00:11:22:33:44:55
+	ip link set p786p2 vf 0 mac 00:11:22:33:44:66
+
+Bind VF device to igb_uio:
+	./usertools/dpdk-devbind.py --bind=igb_uio 0000:08:10.0 0000:08:10.1
+	
+Start VM and start l3fwd-power with two queues per port in VM:
+	l3fwd-power -c 1f -n 4 -- -p 0x3 -P \
+		--config="(0,0,1),(0,1,2)(1,0,3),(1,1,4)"
+
+Send packets with increased dest IP to Port0 and Port1, check that thread on 
+core1,core2,core3,core4 waked up:
+	L3FWD_POWER: lcore 1 is waked up from rx interrupt on port1,rxq0
+	L3FWD_POWER: lcore 2 is waked up from rx interrupt on port1,rxq1
+	L3FWD_POWER: lcore 3 is waked up from rx interrupt on port1,rxq0
+	L3FWD_POWER: lcore 4 is waked up from rx interrupt on port1,rxq1
+	
+Check the packet has been normally forwarded.
+
+After the packet forwarded, thread on core1,core2,core3,core4 will return to 
+sleep.
+	L3FWD_POWER: lcore 1 sleeps until interrupt on port0,rxq0 triggers
+	L3FWD_POWER: lcore 2 sleeps until interrupt on port0,rxq1 triggers
+	L3FWD_POWER: lcore 3 sleeps until interrupt on port1,rxq0 triggers
+	L3FWD_POWER: lcore 4 sleeps until interrupt on port1,rxq1 triggers
+
+Send packet flows to Port0 and Port1, check that thread on core1,core2,core3,
+core4 will keep up awake.
+
+Test Case9: PF interrupt pmd latency test
+=========================================
+Setup validation scenario the case as test1
+Send burst packet flow to Port0 and Port1, use IXIA capture the maxmium 
+latecny.
+
+Compare latency(l3fwd-power PF interrupt pmd with uio) with l3fwd latency.
+
+Setup validation scenario the case as test2
+Send burst packet flow to Port0 and Port1, use IXIA capture the maxmium 
+latecny.
+
+Compare latency(l3fwd-power PF interrupt pmd with vfio) with l3fwd latency.
-- 
1.9.3

Re: [dts] [PATCH V2] add test plan interrupt_pmd

[Liu, Yong]

Thanks gang, applied.

On 01/13/2017 11:56 AM, xu,gang wrote:
> Signed-off-by: xu,gang<gangx.xu@intel.com>
> ---
>   test_plans/interrupt_pmd_test_plan.rst | 262 +++++++++++++++++++++++++++++++++
>   1 file changed, 262 insertions(+)
>   create mode 100644 test_plans/interrupt_pmd_test_plan.rst
>
> diff --git a/test_plans/interrupt_pmd_test_plan.rst b/test_plans/interrupt_pmd_test_plan.rst
> new file mode 100644
> index 0000000..6d4c7c5