test suite reviews and discussions
 help / color / mirror / Atom feed
From: changqingxwu <changqingx.wu@intel.com>
To: dts@dpdk.org
Cc: changqingxwu <changqingx.wu@intel.com>
Subject: [dts] [PATCH V2] test_plans:add test plan about l2fwd_jobstats
Date: Wed,  3 Apr 2019 15:06:54 +0800	[thread overview]
Message-ID: <1554275214-6296-1-git-send-email-changqingx.wu@intel.com> (raw)

Signed-off-by: changqingxwu <changqingx.wu@intel.com>
---
 test_plans/l2fwd_jobstats_test_plan.rst | 82 +++++++++++++++++++++++++
 1 file changed, 82 insertions(+)
 create mode 100644 test_plans/l2fwd_jobstats_test_plan.rst

diff --git a/test_plans/l2fwd_jobstats_test_plan.rst b/test_plans/l2fwd_jobstats_test_plan.rst
new file mode 100644
index 0000000..2090869
--- /dev/null
+++ b/test_plans/l2fwd_jobstats_test_plan.rst
@@ -0,0 +1,82 @@
+.. Copyright (c) < 2019 >, Intel Corporation
+    All rights reserved.
+
+    Redistribution and use in source and binary forms, with or without
+    modification, are permitted provided that the following conditions
+    are met:
+
+    - Redistributions of source code must retain the above copyright
+        notice, this list of conditions and the following disclaimer.
+
+    - Redistributions in binary form must reproduce the above copyright
+        notice, this list of conditions and the following disclaimer in
+        the documentation and / or other materials provided with the
+        distribution.
+
+    - Neither the name of Intel Corporation nor the names of its
+        contributors may be used to endorse or promote products derived
+        from this software without specific prior written permission.
+
+    THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+    "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+    LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+    FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+    COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+    INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+    (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+     SERVICES
+     LOSS OF USE, DATA, OR PROFITS
+     OR BUSINESS INTERRUPTION)
+    HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+    STRICT LIABILITY, OR TORT(INCLUDING NEGLIGENCE OR OTHERWISE)
+    ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+    OF THE POSSIBILITY OF SUCH DAMAGE.
+
+===================
+L2fwd Jobstats Test
+===================
+
+The L2 Forwarding sample application, which can operate in real and virtualized environments, performs
+L2 forwarding for each packet that is received. The destination port is the adjacent port from the
+enabled portmask, that is, if the first four ports are enabled (portmask 0x3), ports 0 and 1 forward
+into each other. Also, the MAC addresses are affected as follows:
+
+- The source MAC address is replaced by the TX port MAC address
+- The destination MAC address is replaced by 02:00:00:00:00:TX_PORT_ID
+
+Prerequisites
+=============
+
+If using vfio the kernel must be >= 3.6+ and VT-d must be enabled in bios.When
+using vfio, use the following commands to load the vfio driver and bind it
+to the device under test::
+
+    modprobe vfio
+    modprobe vfio-pci
+    usertools/dpdk-devbind.py --bind=vfio-pci device_bus_id
+
+The application requires a number of command line options::
+
+    ./build/l2fwd-jobstats [EAL options] -- -p PORTMASK [-q NQ] [-l]
+
+The ``l2fwd-jobstats`` application is run with EAL parameters and parameters for
+the application itself. For details about the EAL parameters, see the relevant
+DPDK **Getting Started Guide**. This application supports three parameters for
+itself.
+
+- p PORTMASK: A hexadecimal bitmask of the ports to configure
+- q NQ: A number of queues (=ports) per lcore (default is 1)
+- l: Use locale thousands separator when formatting big numbers.
+
+Test Case: L2fwd jobstats check
+================================================
+
+Assume port 0 and 1 are connected to the traffic generator, to run the test
+application in linuxapp environment with 4 lcores, 2 ports and 2 RX queues
+per lcore::
+
+    ./examples/l2fwd-jobstats/build/l2fwd-jobstats -c 0x03 -n 4  -- -q 2 -p 0x03 -l
+
+Then send 100, 000 packet to port 0 and 100, 000 packets to port 1, check the
+NIC packets number reported by sample is the same with what we set at the packet
+generator side.
-- 
2.17.2


             reply	other threads:[~2019-04-03  7:04 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-04-03  7:06 changqingxwu [this message]
2019-04-03 18:21 ` Tu, Lijuan
2019-04-11  2:48   ` Wu, ChangqingX

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1554275214-6296-1-git-send-email-changqingx.wu@intel.com \
    --to=changqingx.wu@intel.com \
    --cc=dts@dpdk.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).