* [dts] [PATCH V2] test_plans/iavf:upload test plan
@ 2019-07-24 10:47 zhuwenhui
2019-07-25 1:27 ` Lin, Xueqin
2019-08-07 7:26 ` Tu, Lijuan
0 siblings, 2 replies; 3+ messages in thread
From: zhuwenhui @ 2019-07-24 10:47 UTC (permalink / raw)
To: dts; +Cc: zhuwenhui
Add new test plan.
Signed-off-by: zhuwenhui <wenhuix.zhu@intel.com>
---
test_plans/iavf_test_plan.rst | 498 ++++++++++++++++++++++++++++++++++
1 file changed, 498 insertions(+)
create mode 100644 test_plans/iavf_test_plan.rst
diff --git a/test_plans/iavf_test_plan.rst b/test_plans/iavf_test_plan.rst
new file mode 100644
index 0000000..6081d35
--- /dev/null
+++ b/test_plans/iavf_test_plan.rst
@@ -0,0 +1,498 @@
+# BSD LICENSE
+#
+# Copyright(c) 2019 Intel Corporation. All rights reserved.
+# All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# * Redistributions of source code must retain the above copyright
+# notice, this list of conditions and the following disclaimer.
+# * Redistributions in binary form must reproduce the above copyright
+# notice, this list of conditions and the following disclaimer in
+# the documentation and/or other materials provided with the
+# distribution.
+# * Neither the name of Intel Corporation nor the names of its
+# contributors may be used to endorse or promote products derived
+# from this software without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+# A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+# OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+# LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+# DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+# THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+# (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+# OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+
+====================
+DPDK IAVF API Tests
+====================
+Intel Adaptive Virtual Function(IAVF)
+
+Hardwares
+=======================
+I40E driver NIC (Fortville XXV710, Fortville Spirit, Fortville Eagle)
+
+
+Prerequisites
+=======================
+1. Modify and build DPDK source code to enable IAVF function for I40E NIC::
+
+ sed -i -e '/IAVF_DEV_ID_ADAPTIVE_VF/s/0x1889/0x154c/g' drivers/net/iavf/base/iavf_devids.h
+ sed -i -e '/I40E_DEV_ID_VF/s/0x154C/0x164C/g' drivers/net/i40e/base/i40e_devids.h
+
+ make install RTE_SDK=`pwd` T=x86_64-native-linuxapp-gcc
+
+2. Configure PF and VF::
+
+ modprobe uio;
+ insmod x86_64-native-linuxapp-gcc/kmod/igb_uio.ko;
+ ./usertools/dpdk-devbind.py --bind=igb_uio 08:00.0 08:00.1
+
+ echo 1 > /sys/bus/pci/devices/0000\:08\:00.0/max_vfs
+ echo 1 > /sys/bus/pci/devices/0000\:08\:00.1/max_vfs
+
+3. Start testpmd on host to configure VF ports' mac::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -l 1-5 -n 4 -- -i
+
+ testpmd>set vf mac addr 0 0 00:12:34:56:78:01
+ testpmd>set vf mac addr 1 0 00:12:34:56:78:02
+
+4. Pass through VF 09:02.0 and 09:0a.0 to VM0::
+
+ taskset -c 24,25 qemu-system-x86_64 \
+ -name vm0 -enable-kvm -pidfile /tmp/.vm0.pid -daemonize -monitor unix:/tmp/vm0_monitor.sock,server,nowait \
+ -device e1000,netdev=nttsip1 -netdev user,id=nttsip1,hostfwd=tcp:10.240.176.247:6000-:22 \
+ -device vfio-pci,host=0000:09:02.0,id=pt_0 -device vfio-pci,host=0000:09:0a.0,\
+ id=pt_1 -cpu host -smp 2 -m 10240 -chardev socket,path=/tmp/vm0_qga0.sock,server,nowait,id=vm0_qga0 \
+ -device virtio-serial -device virtserialport,chardev=vm0_qga0,name=org.qemu.guest_agent.0 -vnc :1 \
+ -drive file=/home/image/sriov-fc25-1.img,format=raw,if=virtio,index=0,media=disk
+
+
+5. Modify and build DPDK source code to enable IAVF function for I40E NIC in VM::
+
+ sed -i -e '/IAVF_DEV_ID_ADAPTIVE_VF/s/0x1889/0x154c/g' drivers/net/iavf/base/iavf_devids.h
+ sed -i -e '/I40E_DEV_ID_VF/s/0x154C/0x164C/g' drivers/net/i40e/base/i40e_devids.h
+
+ make install RTE_SDK=`pwd` T=x86_64-native-linuxapp-gcc
+
+6. Bind VF to igb_uio or vfio-pic in VM::
+
+ ./usertools/dpdk-devbind.py --bind=igb_uio 00:04.0 00:05.0
+ or
+ ./usertools/dpdk-devbind.py --bind=vfio-pci 00:04.0 00:05.0
+
+Test case: VF basic RX/TX
+---------------------------
+1. Start testpmd on VM::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
+
+2. Check and verify packets which received and forwarded
+
+
+Test Cases: VF mac filter
+=========================
+
+Start testpmd on VM::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
+
+Test Case: unicast test
+------------------------
+::
+
+ testpmd>set promisc all off
+ testpmd>set allmulti all off
+ testpmd>start
+
+ testpmd>mac_addr set 0 00:12:34:56:78:03
+
+disable promisc mode, verify VF packet rx/tx can work fine with the specific mac addr.
+
+Test Case: multicast test
+-------------------------
+::
+
+ testpmd>set promisc all off
+ testpmd>set allmulti all off
+ testpmd>start
+
+Send packet with multicast MAC 01:80:C2:00:00:08, and check VF can not receive the packet.
+::
+
+ testpmd>set allmulti all on
+
+Send packet with multicast MAC 01:80:C2:00:00:08, and check VF can receive the packet.
+
+Test Case: broadcast test
+-------------------------
+::
+
+ testpmd>set promisc all off
+ testpmd>start
+
+Send packets with broadcast address ff:ff:ff:ff:ff:ff, and check VF can receive the packet
+
+Test Case: promiscuous mode
+---------------------------
+::
+
+ testpmd>set promisc all on
+ testpmd>start
+
+Send packet that different with vf mac, check packets can be received.
+
+Test Cases: VF VLAN feature vlan filter only work with promisc mode off
+==========================================================================
+
+Start testpmd on VM::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
+
+Test Case: vlan filter
+---------------------------
+::
+
+ testpmd>port stop all
+ testpmd>set promisc all off
+ testpmd>vlan set filter off 0
+ testpmd>vlan set filter off 1
+ testpmd>vlan set strip off 0
+ testpmd>vlan set strip off 1
+
+ testpmd>vlan set filter on 0
+ testpmd>set fwd mac
+ testpmd>port start all
+ testpmd>start
+
+packet with vlan can not be received, packet without vlan packet can be received.
+
+Test Case: rx_vlan
+---------------------------
+::
+
+ testpmd>port stop all
+ testpmd>set promisc all off
+ testpmd>vlan set filter off 0
+ testpmd>vlan set filter off 1
+ testpmd>vlan set strip off 0
+ testpmd>vlan set strip off 1
+
+ testpmd>vlan set filter on 0
+ testpmd>rx_vlan add 20 0
+ testpmd>set fwd mac
+ testpmd>port start all
+ testpmd>start
+
+packet vlan id equal to 20 can be received, packet vlan id not equal to 20 packet can be not received.
+
+Test Case: tx_vlan
+---------------------------
+::
+
+ testpmd>port stop all
+ testpmd>set promisc all on
+ testpmd>set fwd mac
+ testpmd>vlan set filter off 0
+ testpmd>vlan set filter off 1
+ testpmd>vlan set strip off 0
+ testpmd>vlan set strip off 1
+ testpmd>tx_vlan set 1 20
+ testpmd>port start all
+ testpmd>start
+
+packet out from VF contain the vlan tag and vlan id equal to 20.
+
+Test Case: vlan strip
+---------------------------
+::
+
+ testpmd>port stop all
+ testpmd>set promisc all on
+ testpmd>set fwd mac
+ testpmd>vlan set filter off 0
+ testpmd>vlan set filter off 1
+ testpmd>vlan set strip off 0
+ testpmd>vlan set strip off 1
+ testpmd>vlan set strip on 0
+ testpmd>port start all
+ testpmd>start
+
+send a packet with vlan tag, packet out from VF not contain the vlan tag.
+
+Test Case: vlan promisc mode
+-----------------------------
+::
+
+ testpmd>port stop all
+ testpmd>vlan set filter off 0
+ testpmd>vlan set filter off 1
+ testpmd>vlan set strip off 0
+ testpmd>vlan set strip off 1
+
+ testpmd>set promisc all on
+ testpmd>set fwd mac
+ testpmd>port start all
+ testpmd>start
+
+send packet with vlan or without vlan, both can be received and forwarded.
+
+Test Cases: VF jumboframe
+==============================
+
+Ensure Tester's ports support sending jumboframe::
+
+ ifconfig 'tester interface' mtu 9000
+
+
+Test Case: Check that no jumbo frame support
+--------------------------------------------
+::
+
+ Launch testpmd for VF ports without enabling jumboframe option
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
+
+ testpmd>set fwd mac
+ testpmd>start
+
+packet less than the standard maximum frame (1518) can be received.
+packet more than the standard maximum frame (1518) can not be received.
+
+Test Case: Check that with jumbo frames support
+------------------------------------------------
+::
+
+ Launch testpmd for VF ports with jumboframe option
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i --max-pkt-len=3000 --tx-offloads=0x8000
+
+ testpmd>set fwd mac
+ testpmd>start
+
+packet lengths greater than the standard maximum frame (1518) and
+lower or equal to the maximum frame length can be received.
+Check that packets larger than the configured maximum packet length are
+dropped by the hardware.
+
+**Note the following was expected!** packet size > 9001, not forward , but RX-packets: counter increased
+
+Test Cases: VF rss
+====================
+Start testpmd on VM::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i --txq=4 --rxq=4
+
+Test Case: test redirection table config
+-------------------------------------------
+::
+
+ testpmd>port config 0 rss reta (0,0)
+ testpmd>port config 0 rss reta (1,1)
+ testpmd>port config 0 rss reta (2,2)
+ testpmd>port config 0 rss reta (3,3)
+ testpmd>port config 0 rss reta (60,0)
+ testpmd>port config 0 rss reta (61,1)
+ testpmd>port config 0 rss reta (62,2)
+ testpmd>port config 0 rss reta (63,3)
+
+ testpmd> port config all rss (all|ip|tcp|udp|sctp|ether|port|vxlan|geneve|nvgre|none)
+
+send different flow type packets to VF port, check packets received by different queues.
+
+Test Cases:VF offload
+=======================
+Start testpmd on VM::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
+
+Test Case: enable HW checksum offload
+-------------------------------------------
+::
+
+ testpmd>port stop all
+ testpmd>csum set ip hw 0
+ testpmd>csum set udp hw 0
+ testpmd>csum set tcp hw 0
+ testpmd>csum set sctp hw 0
+
+ testpmd>csum set ip hw 1
+ testpmd>csum set udp hw 1
+ testpmd>csum set tcp hw 1
+ testpmd>csum set sctp hw 1
+
+ testpmd>set fwd csum
+ testpmd>set verbose 1
+
+ testpmd>port start all
+ testpmd>start
+
+Send packets with incorrect checksum to VF port, verify that the packets
+can be received by VF port and checksum error reported,
+the packets forwarded by VF port have the correct checksum value.
+
+
+Test Case: SW checksum, disable HW checksum offload
+---------------------------------------------------
+::
+
+ testpmd>port stop all
+ testpmd>csum set ip sw 0
+ testpmd>csum set udp sw 0
+ testpmd>csum set tcp sw 0
+ testpmd>csum set sctp sw 0
+
+ testpmd>csum set ip sw 1
+ testpmd>csum set udp sw 1
+ testpmd>csum set tcp sw 1
+ testpmd>csum set sctp sw 1
+
+ testpmd>set fwd csum
+ testpmd>set verbose 1
+ testpmd>port start all
+ testpmd>start
+
+Send packets with incorrect checksum to VF port, verify that the packets
+can be received by VF port and checksum error reported, the packets
+forwarded by VF port have the correct checksum value.
+
+
+Test Case: tso
+-------------------------------------------
+::
+
+ testpmd>port stop all
+ testpmd>set verbose 1
+ testpmd>csum set ip hw 0
+ testpmd>csum set udp hw 0
+ testpmd>csum set tcp hw 0
+ testpmd>csum set sctp hw 0
+
+ testpmd>csum set ip hw 1
+ testpmd>csum set udp hw 1
+ testpmd>csum set tcp hw 1
+ testpmd>csum set sctp hw 1
+
+ testpmd>tso set 800 1
+ testpmd>set fwd csum
+ testpmd>port start all
+ testpmd>start
+
+Send packet which loading size more than 800.
+Verify tcpdump packets send out by VF port is split according to tso size.
+
+Test case: Rx interrupt
+============================
+
+Test case: rx interrupt
+-----------------------
+::
+
+ build l3fwd-power
+ make -C examples/l3fwd-power RTE_SDK=`pwd` T=x86_64-native-linuxapp-gcc
+
+ enable vfio noiommu
+ modprobe -r vfio_iommu_type1
+ modprobe -r vfio
+ modprobe vfio enable_unsafe_noiommu_mode=1
+ cat /sys/module/vfio/parameters/enable_unsafe_noiommu_mode
+ modprobe vfio-pci
+
+ start l3fwd power with one queue per port.
+ ./examples/l3fwd-power/build/l3fwd-power -l 6,7 -n 4 -- \
+ -p 0x3 --config '(0,0,6),(1,0,7)'
+
+ Send one packet to VF0 and VF1, check that thread on core6 and core7 waked up::
+
+ L3FWD_POWER: lcore 6 is waked up from rx interrupt on port 0 queue 0
+ L3FWD_POWER: lcore 7 is waked up from rx interrupt on port 0 queue 0
+
+ Check the packet has been normally forwarded.
+
+ After the packet forwarded, thread on core6 and core 7 will return to sleep::
+
+ L3FWD_POWER: lcore 6 sleeps until interrupt triggers
+ L3FWD_POWER: lcore 7 sleeps until interrupt triggers
+
+ Send packet flows to VF0 and VF1, check that thread on core1 and core2 will
+ keep up awake.
+
+
+Test Cases: VF veb
+=======================
+
+Test Case: veb performance
+--------------------------
+
+create 2 VFs from 1 PF, start testpmd with 2VFs individually, verify throughput.
+
+create 2 VFs from 1 PF, and start PF::
+
+ echo 2 > /sys/bus/pci/devices/0000\:08\:00.0/max_vfs;
+ ./usertools/dpdk-devbind.py --bind=vfio-pci 09:02.0 09:0a.0
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -l 1,2 -n 4 --socket-mem=1024,1024 --file-prefix=pf -w 08:00.0 -- -i
+
+ testpmd>set vf mac addr 0 0 00:12:34:56:78:01
+ testpmd>set vf mac addr 0 1 00:12:34:56:78:02
+
+start testpmd with 2VFs individually::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -l 3-5 -n 4 --master-lcore=3 --socket-mem=1024,1024 --file-prefix=vf1 \
+ -w 09:02.0 -- -i --txq=2 --rxq=2 --rxd=512 --txd=512 --nb-cores=2 --rss-ip --eth-peer=0,00:12:34:56:78:02
+
+ testpmd>set promisc all off
+ testpmd>set fwd mac
+ testpmd>start
+
+::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -l 6-8 -n 4 --master-lcore=6 --socket-mem=1024,1024 --file-prefix=vf2 \
+ -w 09:0a.0 -- -i --txq=2 --rxq=2 --rxd=512 --txd=512 --nb-cores=2 --rss-ip
+
+ testpmd>set promisc all off
+ testpmd>set fwd mac
+ testpmd>start
+
+send traffic and verify throughput.
+
+Test Case: VF performance
+============================
+
+Test Case: vector vf performance
+---------------------------------
+
+1. config vector=y in config/common_base, and rebuild dpdk
+
+2. start testpmd for PF::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x6 -n 4 --socket-mem=1024,1024 --file-prefix=pf \
+ -w 08:00.0 -w 08:00.1 -- -i
+
+ testpmd>set vf mac addr 0 0 00:12:34:56:78:01
+ testpmd>set vf mac addr 1 0 00:12:34:56:78:02
+
+3. start testpmd for VF::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f8 -n 4 --master-lcore=3 --socket-mem=1024,1024 --file-prefix=vf \
+ -w 09:0a.0 -w 09:02.0 -- -i --txq=2 --rxq=2 --rxd=512 --txd=512 --nb-cores=4 --rss-ip
+
+ testpmd>set promisc all off
+ testpmd>set fwd mac
+ testpmd>start
+
+4. send traffic and verify throughput
+
+Test Case: scalar/bulk vf performance
+-------------------------------------
+
+1. change CONFIG_RTE_LIBRTE_IAVF_INC_VECTOR=n in config/common_base, and rebuild dpdk.
+2. repeat test steps 2-4 in above test case: vector vf performance.
--
2.17.2
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [dts] [PATCH V2] test_plans/iavf:upload test plan
2019-07-24 10:47 [dts] [PATCH V2] test_plans/iavf:upload test plan zhuwenhui
@ 2019-07-25 1:27 ` Lin, Xueqin
2019-08-07 7:26 ` Tu, Lijuan
1 sibling, 0 replies; 3+ messages in thread
From: Lin, Xueqin @ 2019-07-25 1:27 UTC (permalink / raw)
To: Zhu, WenhuiX, dts; +Cc: Zhu, WenhuiX
Acked-by: Xueqin Lin <xueqin.lin@intel.com>
> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of zhuwenhui
> Sent: Wednesday, July 24, 2019 6:48 PM
> To: dts@dpdk.org
> Cc: Zhu, WenhuiX <wenhuix.zhu@intel.com>
> Subject: [dts] [PATCH V2] test_plans/iavf:upload test plan
>
> Add new test plan.
>
> Signed-off-by: zhuwenhui <wenhuix.zhu@intel.com>
> ---
> test_plans/iavf_test_plan.rst | 498
> ++++++++++++++++++++++++++++++++++
> 1 file changed, 498 insertions(+)
> create mode 100644 test_plans/iavf_test_plan.rst
>
> diff --git a/test_plans/iavf_test_plan.rst b/test_plans/iavf_test_plan.rst new
> file mode 100644 index 0000000..6081d35
> --- /dev/null
> +++ b/test_plans/iavf_test_plan.rst
> @@ -0,0 +1,498 @@
> +# BSD LICENSE
> +#
> +# Copyright(c) 2019 Intel Corporation. All rights reserved.
> +# All rights reserved.
> +#
> +# Redistribution and use in source and binary forms, with or without #
> +modification, are permitted provided that the following conditions #
> +are met:
> +#
> +# * Redistributions of source code must retain the above copyright
> +# notice, this list of conditions and the following disclaimer.
> +# * Redistributions in binary form must reproduce the above copyright
> +# notice, this list of conditions and the following disclaimer in
> +# the documentation and/or other materials provided with the
> +# distribution.
> +# * Neither the name of Intel Corporation nor the names of its
> +# contributors may be used to endorse or promote products derived
> +# from this software without specific prior written permission.
> +#
> +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
> CONTRIBUTORS #
> +"AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
> #
> +LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
> FITNESS FOR #
> +A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
> COPYRIGHT #
> +OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
> INCIDENTAL, #
> +SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
> NOT #
> +LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
> USE, #
> +DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
> ON ANY #
> +THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
> #
> +(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF
> THE USE #
> +OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
> DAMAGE.
> +
> +
> +====================
> +DPDK IAVF API Tests
> +====================
> +Intel Adaptive Virtual Function(IAVF)
> +
> +Hardwares
> +=======================
> +I40E driver NIC (Fortville XXV710, Fortville Spirit, Fortville Eagle)
> +
> +
> +Prerequisites
> +=======================
> +1. Modify and build DPDK source code to enable IAVF function for I40E NIC::
> +
> + sed -i -e '/IAVF_DEV_ID_ADAPTIVE_VF/s/0x1889/0x154c/g'
> drivers/net/iavf/base/iavf_devids.h
> + sed -i -e '/I40E_DEV_ID_VF/s/0x154C/0x164C/g'
> + drivers/net/i40e/base/i40e_devids.h
> +
> + make install RTE_SDK=`pwd` T=x86_64-native-linuxapp-gcc
> +
> +2. Configure PF and VF::
> +
> + modprobe uio;
> + insmod x86_64-native-linuxapp-gcc/kmod/igb_uio.ko;
> + ./usertools/dpdk-devbind.py --bind=igb_uio 08:00.0 08:00.1
> +
> + echo 1 > /sys/bus/pci/devices/0000\:08\:00.0/max_vfs
> + echo 1 > /sys/bus/pci/devices/0000\:08\:00.1/max_vfs
> +
> +3. Start testpmd on host to configure VF ports' mac::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -l 1-5 -n 4 -- -i
> +
> + testpmd>set vf mac addr 0 0 00:12:34:56:78:01
> + testpmd>set vf mac addr 1 0 00:12:34:56:78:02
> +
> +4. Pass through VF 09:02.0 and 09:0a.0 to VM0::
> +
> + taskset -c 24,25 qemu-system-x86_64 \
> + -name vm0 -enable-kvm -pidfile /tmp/.vm0.pid -daemonize -monitor
> unix:/tmp/vm0_monitor.sock,server,nowait \
> + -device e1000,netdev=nttsip1 -netdev
> user,id=nttsip1,hostfwd=tcp:10.240.176.247:6000-:22 \
> + -device vfio-pci,host=0000:09:02.0,id=pt_0 -device vfio-
> pci,host=0000:09:0a.0,\
> + id=pt_1 -cpu host -smp 2 -m 10240 -chardev
> socket,path=/tmp/vm0_qga0.sock,server,nowait,id=vm0_qga0 \
> + -device virtio-serial -device
> virtserialport,chardev=vm0_qga0,name=org.qemu.guest_agent.0 -vnc :1 \
> + -drive
> + file=/home/image/sriov-fc25-1.img,format=raw,if=virtio,index=0,media=d
> + isk
> +
> +
> +5. Modify and build DPDK source code to enable IAVF function for I40E NIC
> in VM::
> +
> + sed -i -e '/IAVF_DEV_ID_ADAPTIVE_VF/s/0x1889/0x154c/g'
> drivers/net/iavf/base/iavf_devids.h
> + sed -i -e '/I40E_DEV_ID_VF/s/0x154C/0x164C/g'
> + drivers/net/i40e/base/i40e_devids.h
> +
> + make install RTE_SDK=`pwd` T=x86_64-native-linuxapp-gcc
> +
> +6. Bind VF to igb_uio or vfio-pic in VM::
> +
> + ./usertools/dpdk-devbind.py --bind=igb_uio 00:04.0 00:05.0
> + or
> + ./usertools/dpdk-devbind.py --bind=vfio-pci 00:04.0 00:05.0
> +
> +Test case: VF basic RX/TX
> +---------------------------
> +1. Start testpmd on VM::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> +
> +2. Check and verify packets which received and forwarded
> +
> +
> +Test Cases: VF mac filter
> +=========================
> +
> +Start testpmd on VM::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> +
> +Test Case: unicast test
> +------------------------
> +::
> +
> + testpmd>set promisc all off
> + testpmd>set allmulti all off
> + testpmd>start
> +
> + testpmd>mac_addr set 0 00:12:34:56:78:03
> +
> +disable promisc mode, verify VF packet rx/tx can work fine with the specific
> mac addr.
> +
> +Test Case: multicast test
> +-------------------------
> +::
> +
> + testpmd>set promisc all off
> + testpmd>set allmulti all off
> + testpmd>start
> +
> +Send packet with multicast MAC 01:80:C2:00:00:08, and check VF can not
> receive the packet.
> +::
> +
> + testpmd>set allmulti all on
> +
> +Send packet with multicast MAC 01:80:C2:00:00:08, and check VF can
> receive the packet.
> +
> +Test Case: broadcast test
> +-------------------------
> +::
> +
> + testpmd>set promisc all off
> + testpmd>start
> +
> +Send packets with broadcast address ff:ff:ff:ff:ff:ff, and check VF can
> +receive the packet
> +
> +Test Case: promiscuous mode
> +---------------------------
> +::
> +
> + testpmd>set promisc all on
> + testpmd>start
> +
> +Send packet that different with vf mac, check packets can be received.
> +
> +Test Cases: VF VLAN feature vlan filter only work with promisc mode off
> +=============================================================
> ==========
> +===
> +
> +Start testpmd on VM::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> +
> +Test Case: vlan filter
> +---------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>set promisc all off
> + testpmd>vlan set filter off 0
> + testpmd>vlan set filter off 1
> + testpmd>vlan set strip off 0
> + testpmd>vlan set strip off 1
> +
> + testpmd>vlan set filter on 0
> + testpmd>set fwd mac
> + testpmd>port start all
> + testpmd>start
> +
> +packet with vlan can not be received, packet without vlan packet can be
> received.
> +
> +Test Case: rx_vlan
> +---------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>set promisc all off
> + testpmd>vlan set filter off 0
> + testpmd>vlan set filter off 1
> + testpmd>vlan set strip off 0
> + testpmd>vlan set strip off 1
> +
> + testpmd>vlan set filter on 0
> + testpmd>rx_vlan add 20 0
> + testpmd>set fwd mac
> + testpmd>port start all
> + testpmd>start
> +
> +packet vlan id equal to 20 can be received, packet vlan id not equal to 20
> packet can be not received.
> +
> +Test Case: tx_vlan
> +---------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>set promisc all on
> + testpmd>set fwd mac
> + testpmd>vlan set filter off 0
> + testpmd>vlan set filter off 1
> + testpmd>vlan set strip off 0
> + testpmd>vlan set strip off 1
> + testpmd>tx_vlan set 1 20
> + testpmd>port start all
> + testpmd>start
> +
> +packet out from VF contain the vlan tag and vlan id equal to 20.
> +
> +Test Case: vlan strip
> +---------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>set promisc all on
> + testpmd>set fwd mac
> + testpmd>vlan set filter off 0
> + testpmd>vlan set filter off 1
> + testpmd>vlan set strip off 0
> + testpmd>vlan set strip off 1
> + testpmd>vlan set strip on 0
> + testpmd>port start all
> + testpmd>start
> +
> +send a packet with vlan tag, packet out from VF not contain the vlan tag.
> +
> +Test Case: vlan promisc mode
> +-----------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>vlan set filter off 0
> + testpmd>vlan set filter off 1
> + testpmd>vlan set strip off 0
> + testpmd>vlan set strip off 1
> +
> + testpmd>set promisc all on
> + testpmd>set fwd mac
> + testpmd>port start all
> + testpmd>start
> +
> +send packet with vlan or without vlan, both can be received and forwarded.
> +
> +Test Cases: VF jumboframe
> +==============================
> +
> +Ensure Tester's ports support sending jumboframe::
> +
> + ifconfig 'tester interface' mtu 9000
> +
> +
> +Test Case: Check that no jumbo frame support
> +--------------------------------------------
> +::
> +
> + Launch testpmd for VF ports without enabling jumboframe option
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> +
> + testpmd>set fwd mac
> + testpmd>start
> +
> +packet less than the standard maximum frame (1518) can be received.
> +packet more than the standard maximum frame (1518) can not be received.
> +
> +Test Case: Check that with jumbo frames support
> +------------------------------------------------
> +::
> +
> + Launch testpmd for VF ports with jumboframe option
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> + --max-pkt-len=3000 --tx-offloads=0x8000
> +
> + testpmd>set fwd mac
> + testpmd>start
> +
> +packet lengths greater than the standard maximum frame (1518) and lower
> +or equal to the maximum frame length can be received.
> +Check that packets larger than the configured maximum packet length are
> +dropped by the hardware.
> +
> +**Note the following was expected!** packet size > 9001, not forward ,
> +but RX-packets: counter increased
> +
> +Test Cases: VF rss
> +====================
> +Start testpmd on VM::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i --txq=4
> + --rxq=4
> +
> +Test Case: test redirection table config
> +-------------------------------------------
> +::
> +
> + testpmd>port config 0 rss reta (0,0)
> + testpmd>port config 0 rss reta (1,1)
> + testpmd>port config 0 rss reta (2,2)
> + testpmd>port config 0 rss reta (3,3)
> + testpmd>port config 0 rss reta (60,0)
> + testpmd>port config 0 rss reta (61,1)
> + testpmd>port config 0 rss reta (62,2)
> + testpmd>port config 0 rss reta (63,3)
> +
> + testpmd> port config all rss
> + (all|ip|tcp|udp|sctp|ether|port|vxlan|geneve|nvgre|none)
> +
> +send different flow type packets to VF port, check packets received by
> different queues.
> +
> +Test Cases:VF offload
> +=======================
> +Start testpmd on VM::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> +
> +Test Case: enable HW checksum offload
> +-------------------------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>csum set ip hw 0
> + testpmd>csum set udp hw 0
> + testpmd>csum set tcp hw 0
> + testpmd>csum set sctp hw 0
> +
> + testpmd>csum set ip hw 1
> + testpmd>csum set udp hw 1
> + testpmd>csum set tcp hw 1
> + testpmd>csum set sctp hw 1
> +
> + testpmd>set fwd csum
> + testpmd>set verbose 1
> +
> + testpmd>port start all
> + testpmd>start
> +
> +Send packets with incorrect checksum to VF port, verify that the
> +packets can be received by VF port and checksum error reported, the
> +packets forwarded by VF port have the correct checksum value.
> +
> +
> +Test Case: SW checksum, disable HW checksum offload
> +---------------------------------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>csum set ip sw 0
> + testpmd>csum set udp sw 0
> + testpmd>csum set tcp sw 0
> + testpmd>csum set sctp sw 0
> +
> + testpmd>csum set ip sw 1
> + testpmd>csum set udp sw 1
> + testpmd>csum set tcp sw 1
> + testpmd>csum set sctp sw 1
> +
> + testpmd>set fwd csum
> + testpmd>set verbose 1
> + testpmd>port start all
> + testpmd>start
> +
> +Send packets with incorrect checksum to VF port, verify that the
> +packets can be received by VF port and checksum error reported, the
> +packets forwarded by VF port have the correct checksum value.
> +
> +
> +Test Case: tso
> +-------------------------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>set verbose 1
> + testpmd>csum set ip hw 0
> + testpmd>csum set udp hw 0
> + testpmd>csum set tcp hw 0
> + testpmd>csum set sctp hw 0
> +
> + testpmd>csum set ip hw 1
> + testpmd>csum set udp hw 1
> + testpmd>csum set tcp hw 1
> + testpmd>csum set sctp hw 1
> +
> + testpmd>tso set 800 1
> + testpmd>set fwd csum
> + testpmd>port start all
> + testpmd>start
> +
> +Send packet which loading size more than 800.
> +Verify tcpdump packets send out by VF port is split according to tso size.
> +
> +Test case: Rx interrupt
> +============================
> +
> +Test case: rx interrupt
> +-----------------------
> +::
> +
> + build l3fwd-power
> + make -C examples/l3fwd-power RTE_SDK=`pwd`
> + T=x86_64-native-linuxapp-gcc
> +
> + enable vfio noiommu
> + modprobe -r vfio_iommu_type1
> + modprobe -r vfio
> + modprobe vfio enable_unsafe_noiommu_mode=1
> + cat /sys/module/vfio/parameters/enable_unsafe_noiommu_mode
> + modprobe vfio-pci
> +
> + start l3fwd power with one queue per port.
> + ./examples/l3fwd-power/build/l3fwd-power -l 6,7 -n 4 -- \
> + -p 0x3 --config '(0,0,6),(1,0,7)'
> +
> + Send one packet to VF0 and VF1, check that thread on core6 and core7
> waked up::
> +
> + L3FWD_POWER: lcore 6 is waked up from rx interrupt on port 0 queue 0
> + L3FWD_POWER: lcore 7 is waked up from rx interrupt on port 0 queue
> + 0
> +
> + Check the packet has been normally forwarded.
> +
> + After the packet forwarded, thread on core6 and core 7 will return to
> sleep::
> +
> + L3FWD_POWER: lcore 6 sleeps until interrupt triggers
> + L3FWD_POWER: lcore 7 sleeps until interrupt triggers
> +
> + Send packet flows to VF0 and VF1, check that thread on core1 and core2
> will
> + keep up awake.
> +
> +
> +Test Cases: VF veb
> +=======================
> +
> +Test Case: veb performance
> +--------------------------
> +
> +create 2 VFs from 1 PF, start testpmd with 2VFs individually, verify
> throughput.
> +
> +create 2 VFs from 1 PF, and start PF::
> +
> + echo 2 > /sys/bus/pci/devices/0000\:08\:00.0/max_vfs;
> + ./usertools/dpdk-devbind.py --bind=vfio-pci 09:02.0 09:0a.0
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -l 1,2 -n 4
> + --socket-mem=1024,1024 --file-prefix=pf -w 08:00.0 -- -i
> +
> + testpmd>set vf mac addr 0 0 00:12:34:56:78:01
> + testpmd>set vf mac addr 0 1 00:12:34:56:78:02
> +
> +start testpmd with 2VFs individually::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -l 3-5 -n 4 --master-lcore=3 --
> socket-mem=1024,1024 --file-prefix=vf1 \
> + -w 09:02.0 -- -i --txq=2 --rxq=2 --rxd=512 --txd=512 --nb-cores=2
> + --rss-ip --eth-peer=0,00:12:34:56:78:02
> +
> + testpmd>set promisc all off
> + testpmd>set fwd mac
> + testpmd>start
> +
> +::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -l 6-8 -n 4 --master-lcore=6 --
> socket-mem=1024,1024 --file-prefix=vf2 \
> + -w 09:0a.0 -- -i --txq=2 --rxq=2 --rxd=512 --txd=512
> + --nb-cores=2 --rss-ip
> +
> + testpmd>set promisc all off
> + testpmd>set fwd mac
> + testpmd>start
> +
> +send traffic and verify throughput.
> +
> +Test Case: VF performance
> +============================
> +
> +Test Case: vector vf performance
> +---------------------------------
> +
> +1. config vector=y in config/common_base, and rebuild dpdk
> +
> +2. start testpmd for PF::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x6 -n 4 --socket-
> mem=1024,1024 --file-prefix=pf \
> + -w 08:00.0 -w 08:00.1 -- -i
> +
> + testpmd>set vf mac addr 0 0 00:12:34:56:78:01
> + testpmd>set vf mac addr 1 0 00:12:34:56:78:02
> +
> +3. start testpmd for VF::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f8 -n 4 --master-lcore=3
> --socket-mem=1024,1024 --file-prefix=vf \
> + -w 09:0a.0 -w 09:02.0 -- -i --txq=2 --rxq=2 --rxd=512 --txd=512
> + --nb-cores=4 --rss-ip
> +
> + testpmd>set promisc all off
> + testpmd>set fwd mac
> + testpmd>start
> +
> +4. send traffic and verify throughput
> +
> +Test Case: scalar/bulk vf performance
> +-------------------------------------
> +
> +1. change CONFIG_RTE_LIBRTE_IAVF_INC_VECTOR=n in
> config/common_base, and rebuild dpdk.
> +2. repeat test steps 2-4 in above test case: vector vf performance.
> --
> 2.17.2
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [dts] [PATCH V2] test_plans/iavf:upload test plan
2019-07-24 10:47 [dts] [PATCH V2] test_plans/iavf:upload test plan zhuwenhui
2019-07-25 1:27 ` Lin, Xueqin
@ 2019-08-07 7:26 ` Tu, Lijuan
1 sibling, 0 replies; 3+ messages in thread
From: Tu, Lijuan @ 2019-08-07 7:26 UTC (permalink / raw)
To: Zhu, WenhuiX, dts; +Cc: Zhu, WenhuiX
Applied, thanks
> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of zhuwenhui
> Sent: Wednesday, July 24, 2019 6:48 PM
> To: dts@dpdk.org
> Cc: Zhu, WenhuiX <wenhuix.zhu@intel.com>
> Subject: [dts] [PATCH V2] test_plans/iavf:upload test plan
>
> Add new test plan.
>
> Signed-off-by: zhuwenhui <wenhuix.zhu@intel.com>
> ---
> test_plans/iavf_test_plan.rst | 498 ++++++++++++++++++++++++++++++++++
> 1 file changed, 498 insertions(+)
> create mode 100644 test_plans/iavf_test_plan.rst
>
> diff --git a/test_plans/iavf_test_plan.rst b/test_plans/iavf_test_plan.rst new
> file mode 100644 index 0000000..6081d35
> --- /dev/null
> +++ b/test_plans/iavf_test_plan.rst
> @@ -0,0 +1,498 @@
> +# BSD LICENSE
> +#
> +# Copyright(c) 2019 Intel Corporation. All rights reserved.
> +# All rights reserved.
> +#
> +# Redistribution and use in source and binary forms, with or without #
> +modification, are permitted provided that the following conditions #
> +are met:
> +#
> +# * Redistributions of source code must retain the above copyright
> +# notice, this list of conditions and the following disclaimer.
> +# * Redistributions in binary form must reproduce the above copyright
> +# notice, this list of conditions and the following disclaimer in
> +# the documentation and/or other materials provided with the
> +# distribution.
> +# * Neither the name of Intel Corporation nor the names of its
> +# contributors may be used to endorse or promote products derived
> +# from this software without specific prior written permission.
> +#
> +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
> CONTRIBUTORS #
> +"AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT #
> +LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
> FOR #
> +A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
> COPYRIGHT #
> +OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
> INCIDENTAL, #
> +SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
> #
> +LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
> USE, #
> +DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
> ON ANY #
> +THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT #
> +(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
> USE #
> +OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> +
> +
> +====================
> +DPDK IAVF API Tests
> +====================
> +Intel Adaptive Virtual Function(IAVF)
> +
> +Hardwares
> +=======================
> +I40E driver NIC (Fortville XXV710, Fortville Spirit, Fortville Eagle)
> +
> +
> +Prerequisites
> +=======================
> +1. Modify and build DPDK source code to enable IAVF function for I40E NIC::
> +
> + sed -i -e '/IAVF_DEV_ID_ADAPTIVE_VF/s/0x1889/0x154c/g'
> drivers/net/iavf/base/iavf_devids.h
> + sed -i -e '/I40E_DEV_ID_VF/s/0x154C/0x164C/g'
> + drivers/net/i40e/base/i40e_devids.h
> +
> + make install RTE_SDK=`pwd` T=x86_64-native-linuxapp-gcc
> +
> +2. Configure PF and VF::
> +
> + modprobe uio;
> + insmod x86_64-native-linuxapp-gcc/kmod/igb_uio.ko;
> + ./usertools/dpdk-devbind.py --bind=igb_uio 08:00.0 08:00.1
> +
> + echo 1 > /sys/bus/pci/devices/0000\:08\:00.0/max_vfs
> + echo 1 > /sys/bus/pci/devices/0000\:08\:00.1/max_vfs
> +
> +3. Start testpmd on host to configure VF ports' mac::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -l 1-5 -n 4 -- -i
> +
> + testpmd>set vf mac addr 0 0 00:12:34:56:78:01
> + testpmd>set vf mac addr 1 0 00:12:34:56:78:02
> +
> +4. Pass through VF 09:02.0 and 09:0a.0 to VM0::
> +
> + taskset -c 24,25 qemu-system-x86_64 \
> + -name vm0 -enable-kvm -pidfile /tmp/.vm0.pid -daemonize -monitor
> unix:/tmp/vm0_monitor.sock,server,nowait \
> + -device e1000,netdev=nttsip1 -netdev
> user,id=nttsip1,hostfwd=tcp:10.240.176.247:6000-:22 \
> + -device vfio-pci,host=0000:09:02.0,id=pt_0 -device vfio-
> pci,host=0000:09:0a.0,\
> + id=pt_1 -cpu host -smp 2 -m 10240 -chardev
> socket,path=/tmp/vm0_qga0.sock,server,nowait,id=vm0_qga0 \
> + -device virtio-serial -device
> virtserialport,chardev=vm0_qga0,name=org.qemu.guest_agent.0 -vnc :1 \
> + -drive
> + file=/home/image/sriov-fc25-1.img,format=raw,if=virtio,index=0,media=d
> + isk
> +
> +
> +5. Modify and build DPDK source code to enable IAVF function for I40E NIC
> in VM::
> +
> + sed -i -e '/IAVF_DEV_ID_ADAPTIVE_VF/s/0x1889/0x154c/g'
> drivers/net/iavf/base/iavf_devids.h
> + sed -i -e '/I40E_DEV_ID_VF/s/0x154C/0x164C/g'
> + drivers/net/i40e/base/i40e_devids.h
> +
> + make install RTE_SDK=`pwd` T=x86_64-native-linuxapp-gcc
> +
> +6. Bind VF to igb_uio or vfio-pic in VM::
> +
> + ./usertools/dpdk-devbind.py --bind=igb_uio 00:04.0 00:05.0
> + or
> + ./usertools/dpdk-devbind.py --bind=vfio-pci 00:04.0 00:05.0
> +
> +Test case: VF basic RX/TX
> +---------------------------
> +1. Start testpmd on VM::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> +
> +2. Check and verify packets which received and forwarded
> +
> +
> +Test Cases: VF mac filter
> +=========================
> +
> +Start testpmd on VM::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> +
> +Test Case: unicast test
> +------------------------
> +::
> +
> + testpmd>set promisc all off
> + testpmd>set allmulti all off
> + testpmd>start
> +
> + testpmd>mac_addr set 0 00:12:34:56:78:03
> +
> +disable promisc mode, verify VF packet rx/tx can work fine with the specific
> mac addr.
> +
> +Test Case: multicast test
> +-------------------------
> +::
> +
> + testpmd>set promisc all off
> + testpmd>set allmulti all off
> + testpmd>start
> +
> +Send packet with multicast MAC 01:80:C2:00:00:08, and check VF can not
> receive the packet.
> +::
> +
> + testpmd>set allmulti all on
> +
> +Send packet with multicast MAC 01:80:C2:00:00:08, and check VF can
> receive the packet.
> +
> +Test Case: broadcast test
> +-------------------------
> +::
> +
> + testpmd>set promisc all off
> + testpmd>start
> +
> +Send packets with broadcast address ff:ff:ff:ff:ff:ff, and check VF can
> +receive the packet
> +
> +Test Case: promiscuous mode
> +---------------------------
> +::
> +
> + testpmd>set promisc all on
> + testpmd>start
> +
> +Send packet that different with vf mac, check packets can be received.
> +
> +Test Cases: VF VLAN feature vlan filter only work with promisc mode off
> +===============================================================
> ========
> +===
> +
> +Start testpmd on VM::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> +
> +Test Case: vlan filter
> +---------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>set promisc all off
> + testpmd>vlan set filter off 0
> + testpmd>vlan set filter off 1
> + testpmd>vlan set strip off 0
> + testpmd>vlan set strip off 1
> +
> + testpmd>vlan set filter on 0
> + testpmd>set fwd mac
> + testpmd>port start all
> + testpmd>start
> +
> +packet with vlan can not be received, packet without vlan packet can be
> received.
> +
> +Test Case: rx_vlan
> +---------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>set promisc all off
> + testpmd>vlan set filter off 0
> + testpmd>vlan set filter off 1
> + testpmd>vlan set strip off 0
> + testpmd>vlan set strip off 1
> +
> + testpmd>vlan set filter on 0
> + testpmd>rx_vlan add 20 0
> + testpmd>set fwd mac
> + testpmd>port start all
> + testpmd>start
> +
> +packet vlan id equal to 20 can be received, packet vlan id not equal to 20
> packet can be not received.
> +
> +Test Case: tx_vlan
> +---------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>set promisc all on
> + testpmd>set fwd mac
> + testpmd>vlan set filter off 0
> + testpmd>vlan set filter off 1
> + testpmd>vlan set strip off 0
> + testpmd>vlan set strip off 1
> + testpmd>tx_vlan set 1 20
> + testpmd>port start all
> + testpmd>start
> +
> +packet out from VF contain the vlan tag and vlan id equal to 20.
> +
> +Test Case: vlan strip
> +---------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>set promisc all on
> + testpmd>set fwd mac
> + testpmd>vlan set filter off 0
> + testpmd>vlan set filter off 1
> + testpmd>vlan set strip off 0
> + testpmd>vlan set strip off 1
> + testpmd>vlan set strip on 0
> + testpmd>port start all
> + testpmd>start
> +
> +send a packet with vlan tag, packet out from VF not contain the vlan tag.
> +
> +Test Case: vlan promisc mode
> +-----------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>vlan set filter off 0
> + testpmd>vlan set filter off 1
> + testpmd>vlan set strip off 0
> + testpmd>vlan set strip off 1
> +
> + testpmd>set promisc all on
> + testpmd>set fwd mac
> + testpmd>port start all
> + testpmd>start
> +
> +send packet with vlan or without vlan, both can be received and forwarded.
> +
> +Test Cases: VF jumboframe
> +==============================
> +
> +Ensure Tester's ports support sending jumboframe::
> +
> + ifconfig 'tester interface' mtu 9000
> +
> +
> +Test Case: Check that no jumbo frame support
> +--------------------------------------------
> +::
> +
> + Launch testpmd for VF ports without enabling jumboframe option
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> +
> + testpmd>set fwd mac
> + testpmd>start
> +
> +packet less than the standard maximum frame (1518) can be received.
> +packet more than the standard maximum frame (1518) can not be received.
> +
> +Test Case: Check that with jumbo frames support
> +------------------------------------------------
> +::
> +
> + Launch testpmd for VF ports with jumboframe option
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> + --max-pkt-len=3000 --tx-offloads=0x8000
> +
> + testpmd>set fwd mac
> + testpmd>start
> +
> +packet lengths greater than the standard maximum frame (1518) and lower
> +or equal to the maximum frame length can be received.
> +Check that packets larger than the configured maximum packet length are
> +dropped by the hardware.
> +
> +**Note the following was expected!** packet size > 9001, not forward ,
> +but RX-packets: counter increased
> +
> +Test Cases: VF rss
> +====================
> +Start testpmd on VM::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i --txq=4
> + --rxq=4
> +
> +Test Case: test redirection table config
> +-------------------------------------------
> +::
> +
> + testpmd>port config 0 rss reta (0,0)
> + testpmd>port config 0 rss reta (1,1)
> + testpmd>port config 0 rss reta (2,2)
> + testpmd>port config 0 rss reta (3,3)
> + testpmd>port config 0 rss reta (60,0)
> + testpmd>port config 0 rss reta (61,1)
> + testpmd>port config 0 rss reta (62,2)
> + testpmd>port config 0 rss reta (63,3)
> +
> + testpmd> port config all rss
> + (all|ip|tcp|udp|sctp|ether|port|vxlan|geneve|nvgre|none)
> +
> +send different flow type packets to VF port, check packets received by
> different queues.
> +
> +Test Cases:VF offload
> +=======================
> +Start testpmd on VM::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x3 -n 1 -- -i
> +
> +Test Case: enable HW checksum offload
> +-------------------------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>csum set ip hw 0
> + testpmd>csum set udp hw 0
> + testpmd>csum set tcp hw 0
> + testpmd>csum set sctp hw 0
> +
> + testpmd>csum set ip hw 1
> + testpmd>csum set udp hw 1
> + testpmd>csum set tcp hw 1
> + testpmd>csum set sctp hw 1
> +
> + testpmd>set fwd csum
> + testpmd>set verbose 1
> +
> + testpmd>port start all
> + testpmd>start
> +
> +Send packets with incorrect checksum to VF port, verify that the
> +packets can be received by VF port and checksum error reported, the
> +packets forwarded by VF port have the correct checksum value.
> +
> +
> +Test Case: SW checksum, disable HW checksum offload
> +---------------------------------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>csum set ip sw 0
> + testpmd>csum set udp sw 0
> + testpmd>csum set tcp sw 0
> + testpmd>csum set sctp sw 0
> +
> + testpmd>csum set ip sw 1
> + testpmd>csum set udp sw 1
> + testpmd>csum set tcp sw 1
> + testpmd>csum set sctp sw 1
> +
> + testpmd>set fwd csum
> + testpmd>set verbose 1
> + testpmd>port start all
> + testpmd>start
> +
> +Send packets with incorrect checksum to VF port, verify that the
> +packets can be received by VF port and checksum error reported, the
> +packets forwarded by VF port have the correct checksum value.
> +
> +
> +Test Case: tso
> +-------------------------------------------
> +::
> +
> + testpmd>port stop all
> + testpmd>set verbose 1
> + testpmd>csum set ip hw 0
> + testpmd>csum set udp hw 0
> + testpmd>csum set tcp hw 0
> + testpmd>csum set sctp hw 0
> +
> + testpmd>csum set ip hw 1
> + testpmd>csum set udp hw 1
> + testpmd>csum set tcp hw 1
> + testpmd>csum set sctp hw 1
> +
> + testpmd>tso set 800 1
> + testpmd>set fwd csum
> + testpmd>port start all
> + testpmd>start
> +
> +Send packet which loading size more than 800.
> +Verify tcpdump packets send out by VF port is split according to tso size.
> +
> +Test case: Rx interrupt
> +============================
> +
> +Test case: rx interrupt
> +-----------------------
> +::
> +
> + build l3fwd-power
> + make -C examples/l3fwd-power RTE_SDK=`pwd`
> + T=x86_64-native-linuxapp-gcc
> +
> + enable vfio noiommu
> + modprobe -r vfio_iommu_type1
> + modprobe -r vfio
> + modprobe vfio enable_unsafe_noiommu_mode=1
> + cat /sys/module/vfio/parameters/enable_unsafe_noiommu_mode
> + modprobe vfio-pci
> +
> + start l3fwd power with one queue per port.
> + ./examples/l3fwd-power/build/l3fwd-power -l 6,7 -n 4 -- \
> + -p 0x3 --config '(0,0,6),(1,0,7)'
> +
> + Send one packet to VF0 and VF1, check that thread on core6 and core7
> waked up::
> +
> + L3FWD_POWER: lcore 6 is waked up from rx interrupt on port 0 queue 0
> + L3FWD_POWER: lcore 7 is waked up from rx interrupt on port 0 queue
> + 0
> +
> + Check the packet has been normally forwarded.
> +
> + After the packet forwarded, thread on core6 and core 7 will return to
> sleep::
> +
> + L3FWD_POWER: lcore 6 sleeps until interrupt triggers
> + L3FWD_POWER: lcore 7 sleeps until interrupt triggers
> +
> + Send packet flows to VF0 and VF1, check that thread on core1 and core2
> will
> + keep up awake.
> +
> +
> +Test Cases: VF veb
> +=======================
> +
> +Test Case: veb performance
> +--------------------------
> +
> +create 2 VFs from 1 PF, start testpmd with 2VFs individually, verify
> throughput.
> +
> +create 2 VFs from 1 PF, and start PF::
> +
> + echo 2 > /sys/bus/pci/devices/0000\:08\:00.0/max_vfs;
> + ./usertools/dpdk-devbind.py --bind=vfio-pci 09:02.0 09:0a.0
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -l 1,2 -n 4
> + --socket-mem=1024,1024 --file-prefix=pf -w 08:00.0 -- -i
> +
> + testpmd>set vf mac addr 0 0 00:12:34:56:78:01
> + testpmd>set vf mac addr 0 1 00:12:34:56:78:02
> +
> +start testpmd with 2VFs individually::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -l 3-5 -n 4 --master-lcore=3 --
> socket-mem=1024,1024 --file-prefix=vf1 \
> + -w 09:02.0 -- -i --txq=2 --rxq=2 --rxd=512 --txd=512 --nb-cores=2
> + --rss-ip --eth-peer=0,00:12:34:56:78:02
> +
> + testpmd>set promisc all off
> + testpmd>set fwd mac
> + testpmd>start
> +
> +::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -l 6-8 -n 4 --master-lcore=6 --
> socket-mem=1024,1024 --file-prefix=vf2 \
> + -w 09:0a.0 -- -i --txq=2 --rxq=2 --rxd=512 --txd=512
> + --nb-cores=2 --rss-ip
> +
> + testpmd>set promisc all off
> + testpmd>set fwd mac
> + testpmd>start
> +
> +send traffic and verify throughput.
> +
> +Test Case: VF performance
> +============================
> +
> +Test Case: vector vf performance
> +---------------------------------
> +
> +1. config vector=y in config/common_base, and rebuild dpdk
> +
> +2. start testpmd for PF::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x6 -n 4 --socket-
> mem=1024,1024 --file-prefix=pf \
> + -w 08:00.0 -w 08:00.1 -- -i
> +
> + testpmd>set vf mac addr 0 0 00:12:34:56:78:01
> + testpmd>set vf mac addr 1 0 00:12:34:56:78:02
> +
> +3. start testpmd for VF::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f8 -n 4 --master-lcore=3
> --socket-mem=1024,1024 --file-prefix=vf \
> + -w 09:0a.0 -w 09:02.0 -- -i --txq=2 --rxq=2 --rxd=512 --txd=512
> + --nb-cores=4 --rss-ip
> +
> + testpmd>set promisc all off
> + testpmd>set fwd mac
> + testpmd>start
> +
> +4. send traffic and verify throughput
> +
> +Test Case: scalar/bulk vf performance
> +-------------------------------------
> +
> +1. change CONFIG_RTE_LIBRTE_IAVF_INC_VECTOR=n in
> config/common_base, and rebuild dpdk.
> +2. repeat test steps 2-4 in above test case: vector vf performance.
> --
> 2.17.2
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-08-07 7:26 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-07-24 10:47 [dts] [PATCH V2] test_plans/iavf:upload test plan zhuwenhui
2019-07-25 1:27 ` Lin, Xueqin
2019-08-07 7:26 ` Tu, Lijuan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).