* [dts] [PATCH] test_plans: change some test parameters
@ 2019-09-18 6:32 Peng Yuan
2019-09-20 6:48 ` Tu, Lijuan
0 siblings, 1 reply; 2+ messages in thread
From: Peng Yuan @ 2019-09-18 6:32 UTC (permalink / raw)
To: dts; +Cc: pengyuan
From: pengyuan <yuan.peng@intel.com>
Change some test parameters for vf_pf_reset_test_plan.rst
Signed-off-by: pengyuan <yuan.peng@intel.com>
diff --git a/test_plans/vf_pf_reset_test_plan.rst b/test_plans/vf_pf_reset_test_plan.rst
index 7d526c8..51a3e3d 100644
--- a/test_plans/vf_pf_reset_test_plan.rst
+++ b/test_plans/vf_pf_reset_test_plan.rst
@@ -1,4 +1,4 @@
-.. Copyright (c) <2015-2017>, Intel Corporation
+.. Copyright (c) <2015-2019>, Intel Corporation
All rights reserved.
Redistribution and use in source and binary forms, with or without
@@ -34,6 +34,7 @@
VF PF Reset Tests
=================
+ The scenario is kernel PF + DPDK VF
Prerequisites
=============
@@ -51,13 +52,18 @@ Prerequisites
testpmd> port reset (port_id|all)
"Reset all ports or port_id"
+3. Enable pf private flags::
+
+ ethtool --set-priv-flags ens5f0 link-down-on-close on
+ ethtool --set-priv-flags ens5f1 link-down-on-close on
+
Test Case 1: vf reset -- create two vfs on one pf
=================================================
-1. Got the pci device id of DUT, for example::
+1. Get the pci device id of DUT, for example::
- ./dpdk_nic_bind.py --st
+ ./usertools/dpdk-devbind.py -s
0000:81:00.0 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f0 drv=i40e
0000:81:00.1 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f1 drv=i40e
@@ -65,7 +71,7 @@ Test Case 1: vf reset -- create two vfs on one pf
2. Create 2 VFs from 1 PF,and set the VF MAC address at PF0::
echo 2 > /sys/bus/pci/devices/0000\:81\:00.0/sriov_numvfs
- ./dpdk_nic_bind.py --st
+ ./usertools/dpdk-devbind.py -s
0000:81:00.0 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f0 drv=i40e
0000:81:02.0 'XL710/X710 Virtual Function' unused=
@@ -75,7 +81,7 @@ Test Case 1: vf reset -- create two vfs on one pf
3. Bind the VFs to dpdk driver::
- ./tools/dpdk-devbind.py -b vfio-pci 81:02.0 81:02.1
+ ./usertools/dpdk-devbind.py -b vfio-pci 81:02.0 81:02.1
4. Set the VLAN id of VF1 and VF2::
@@ -85,7 +91,7 @@ Test Case 1: vf reset -- create two vfs on one pf
5. Run testpmd::
./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 -- -i \
- --portmask=0x3 --tx-offloads=0x8fff --crc-strip
+ --portmask=0x3
testpmd> set fwd mac
testpmd> start
testpmd> set allmulti all on
@@ -95,7 +101,7 @@ Test Case 1: vf reset -- create two vfs on one pf
Promiscuous mode: disabled
Allmulticast mode: enabled
- the status are not different from the default value.
+ The status are not different from the default value.
6. Get mac address of one VF and use it as dest mac, using scapy to
send 1000 random packets from tester, verify the packets can be received
@@ -105,21 +111,19 @@ Test Case 1: vf reset -- create two vfs on one pf
>>>sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=1)/IP()/Raw('x'*40)], \
iface="ens3f0",count=1000)
-7. Reset pf::
-
- ifconfig ens5f0 promisc
+7. Set pf down::
- or::
+ ifconfig ens5f0 down
- ifconfig ens5f0 -promisc
+ Send the same 1000 packets with scapy from tester,
+ the vf cannot receive any packets, including vlan=0 and vlan=1
-8. Vf receive a pf reset message::
+8. Set pf up::
- Event type: RESET interrupt on port 0
- Event type: RESET interrupt on port 1
+ ifconfig ens5f0 up
- if don't reset the vf, send the same 1000 packets with scapy from tester,
- the vf cannot receive any packets, including vlan=0 and vlan=1
+ Send the same 1000 packets with scapy from tester, verify the packets can be
+ received by one VF and can be forward to another VF correctly.
9. Reset the vfs, run the command::
@@ -128,8 +132,8 @@ Test Case 1: vf reset -- create two vfs on one pf
testpmd> port reset 1
testpmd> start
- or just run the command "port reset all"
- send the same 1000 packets with scapy from tester, verify the packets can be
+ or just run the command "port reset all".
+ Send the same 1000 packets with scapy from tester, verify the packets can be
received by one VF and can be forward to another VF correctly,
check the port info::
@@ -145,7 +149,8 @@ Test Case 1: vf reset -- create two vfs on one pf
Promiscuous mode: disabled
Allmulticast mode: enabled
- the info status is consistent to the status before reset.
+ The info status is consistent to the status before reset.
+
Test Case 2: vf reset -- create two vfs on one pf, run testpmd separately
=========================================================================
@@ -156,11 +161,11 @@ Test Case 2: vf reset -- create two vfs on one pf, run testpmd separately
./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 \
--socket-mem 1024,1024 -w 81:02.0 --file-prefix=test1 \
- -- -i --crc-strip --eth-peer=0,00:11:22:33:44:12 \
+ -- -i --eth-peer=0,00:11:22:33:44:12 \
./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf0 -n 4 \
--socket-mem 1024,1024 -w 81:02.1 --file-prefix=test2 \
- -- -i --crc-strip
+ -- -i
3. Set fwd mode on vf0::
@@ -180,7 +185,7 @@ Test Case 2: vf reset -- create two vfs on one pf, run testpmd separately
vf0 can forward the packets to vf1.
6. Reset pf, don't reset vf0 and vf1, send the packets,
- vf0 and vf1 cannot receive any packets.
+ vf0 can forward the packet to vf1.
7. Reset vf0 and vf1, send the packets,
vf0 can forward the packet to vf1.
@@ -203,7 +208,7 @@ Test Case 3: vf reset -- create one vf on each pf
3. Start one testpmd on two vf ports::
./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 -- -i \
- --portmask=0x3 --tx-offloads=0x8fff --crc-strip
+ --portmask=0x3
4. Start forwarding::
@@ -218,7 +223,7 @@ Test Case 3: vf reset -- create one vf on each pf
vfs can fwd the packets normally.
6. Reset pf0 and pf1, don't reset vf0 and vf1, send the packets,
- vfs cannot receive any packets.
+ vfs can fwd the packets normally.
7. Reset vf0 and vf1, send the packets,
vfs can fwd the packets normally.
@@ -230,7 +235,7 @@ Test Case 4: vlan rx restore -- vf reset all ports
1. Execute the step1-step3 of test case 1, then start the testpmd::
./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 -- -i \
- --portmask=0x3 --tx-offloads=0x8fff --crc-strip
+ --portmask=0x3
testpmd> set fwd mac
2. Add vlan on both ports::
@@ -239,7 +244,7 @@ Test Case 4: vlan rx restore -- vf reset all ports
testpmd> rx_vlan add 1 1
testpmd> start
- send packets with scapy from tester::
+ Send packets with scapy from tester::
sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
@@ -251,7 +256,7 @@ Test Case 4: vlan rx restore -- vf reset all ports
iface="ens3f0",count=1000)
vfs can receive the packets and forward it.
- send packets with scapy from tester::
+ Send packets with scapy from tester::
sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=2)/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
@@ -259,7 +264,7 @@ Test Case 4: vlan rx restore -- vf reset all ports
vf0 cannot receive any packets.
3. Reset pf, don't reset vf, send the packets in step2 from tester,
- the vfs cannot receive any packets.
+ vfs can receive the packets and forward it.
4. Reset both vfs::
@@ -267,9 +272,9 @@ Test Case 4: vlan rx restore -- vf reset all ports
testpmd> port reset all
testpmd> start
- send the packets in step2 from tester
+ Send the packets in step2 from tester,
vfs can receive the packets and forward it.
- send packets with scapy from tester::
+ Send packets with scapy from tester::
sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=2)/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
@@ -283,7 +288,7 @@ test Case 5: vlan rx restore -- vf reset one port
1. Execute the step1-step3 of test case 1, then start the testpmd::
./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 -- -i \
- --portmask=0x3 --tx-offloads=0x8fff --crc-strip
+ --portmask=0x3
testpmd> set fwd mac
2. Add vlan on both ports::
@@ -292,7 +297,7 @@ test Case 5: vlan rx restore -- vf reset one port
testpmd> rx_vlan add 1 1
testpmd> start
- send packets with scapy from tester::
+ Send packets with scapy from tester::
sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
@@ -315,15 +320,15 @@ test Case 5: vlan rx restore -- vf reset one port
sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=1)/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
- vf0 can receive the packets, but vf1 can't transmit the packets.
- send packets from tester::
+ vfs can receive and forward the packets.
+ Send packets from tester::
sendp([Ether(dst="00:11:22:33:44:12")/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
sendp([Ether(dst="00:11:22:33:44:12")/Dot1Q(vlan=1)/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
- vf1 cannot receive the packets.
+ vfs can receive and forward the packets.
4. Reset vf1::
@@ -365,13 +370,13 @@ Test Case 6: vlan rx restore -- create one vf on each pf
iface="ens3f0",count=1000)
vfs can forward the packets normally.
- send packets with scapy from tester::
+ Send packets with scapy from tester::
sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=2)/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
vf0 cannot receive any packets.
- remove vlan 0 on vf1::
+ Remove vlan 0 on vf1::
testpmd> rx_vlan rm 0 1
sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \
@@ -383,10 +388,14 @@ Test Case 6: vlan rx restore -- create one vf on each pf
sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
+
+ vf0 can receive the packets, but vf1 can't transmit the packets.
+ Send packets from tester::
+
sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=1)/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
- the vfs cannot receive any packets.
+ vfs can forward the packets normally.
4. Reset both vfs, send packets from tester::
@@ -397,7 +406,7 @@ Test Case 6: vlan rx restore -- create one vf on each pf
iface="ens3f0",count=1000)
vf0 can receive the packets, but vf1 can't transmit the packets.
- send packets from tester::
+ Send packets from tester::
sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=1)/IP()/Raw('x'*1000)], \
iface="ens3f0",count=1000)
@@ -413,9 +422,9 @@ Test Case 7: vlan tx restore
2. Run testpmd::
./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 -- -i \
- --portmask=0x3 --tx-offloads=0x8fff --crc-strip
+ --portmask=0x3
-2. Add tx vlan offload on VF1 port, take care the first param is port,
+3. Add tx vlan offload on VF1 port, take care the first param is port,
start forwarding::
testpmd> set fwd mac
@@ -426,18 +435,18 @@ Test Case 7: vlan tx restore
testpmd> tx_vlan set 1 51
testpmd> start
-3. Send packets with scapy from tester::
+4. Send packets with scapy from tester::
sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*18)], \
iface="ens3f0",count=1)
-4. Listening the port ens3f0::
+5. Listening the port ens3f0::
tcpdump -i ens3f0 -n -e -x -v
check the packet received, the packet is configured with vlan 51
-5. Reset the pf, then reset the two vfs,
+6. Reset the pf, then reset the two vfs,
send the same packet with no vlan tag,
check packets received by tester, the packet is configured with vlan 51.
@@ -457,7 +466,7 @@ test Case 8: MAC address restore
3. Start testpmd on two vf ports::
./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 \
- -- -i --portmask=0x3 --tx-offloads=0x8fff --crc-strip
+ -- -i --portmask=0x3
4. Add MAC address to the vf0 ports::
@@ -466,6 +475,7 @@ test Case 8: MAC address restore
5. Start forwarding::
+ testpmd> set promisc all off
testpmd> set fwd mac
testpmd> start
@@ -479,7 +489,7 @@ test Case 8: MAC address restore
vfs can forward both of the two type packets.
7. Reset pf0 and pf1, don't reset vf0 and vf1, send the two packets,
- vf0 and vf1 cannot receive any packets.
+ vfs can forward both of the two type packets.
8. Reset vf0 and vf1, send the two packets,
vfs can forward both of the two type packets.
@@ -491,7 +501,7 @@ test Case 9: vf reset (two vfs passed through to one VM)
1. Create 2 VFs from 1 PF,and set the VF MAC address at PF0::
echo 2 > /sys/bus/pci/devices/0000\:81\:00.0/sriov_numvfs
- ./dpdk_nic_bind.py --st
+ ./usertools/dpdk-devbind.py -s
0000:81:00.0 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f0 drv=i40e
0000:81:02.0 'XL710/X710 Virtual Function' unused=
@@ -500,14 +510,14 @@ test Case 9: vf reset (two vfs passed through to one VM)
2. Detach VFs from the host, bind them to pci-stub driver::
modprobe pci-stub
- ./tools/dpdk_nic_bind.py --bind=pci_stub 81:02.0 81:02.1
+ ./usertools/dpdk-devbind.py -b pci_stub 81:02.0 81:02.1
or using the following way::
virsh nodedev-detach pci_0000_81_02_0;
virsh nodedev-detach pci_0000_81_02_1;
- ./dpdk_nic_bind.py --st
+ ./usertools/dpdk-devbind.py -s
0000:81:00.0 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f0 drv=i40e
0000:81:02.0 'XL710/X710 Virtual Function' if= drv=pci-stub unused=
@@ -525,9 +535,9 @@ test Case 9: vf reset (two vfs passed through to one VM)
4. Login vm0, got VFs pci device id in vm0, assume they are 00:05.0 & 00:05.1,
bind them to igb_uio driver,and then start testpmd::
- ./tools/dpdk_nic_bind.py --bind=igb_uio 00:05.0 00:05.1
+ ./usertools/dpdk-devbind.py -b igb_uio 00:05.0 00:05.1
./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 \
- -w 00:05.0 -w 00:05.1 -- -i --portmask=0x3 --tx-offloads=0x8fff
+ -w 00:05.0 -w 00:05.1 -- -i --portmask=0x3
5. Add MAC address to the vf0 ports, set it in mac forward mode::
@@ -546,7 +556,7 @@ test Case 9: vf reset (two vfs passed through to one VM)
vfs can forward both of the two type packets.
7. Reset pf0 and pf1, don't reset vf0 and vf1, send the two packets,
- vf0 and vf1 cannot receive any packets.
+ vfs can forward both of the two type packets.
8. Reset vf0 and vf1, send the two packets,
vfs can forward both of the two type packets.
@@ -558,7 +568,7 @@ test Case 10: vf reset (two vfs passed through to two VM)
1. Create 2 VFs from 1 PF,and set the VF MAC address at PF::
echo 2 > /sys/bus/pci/devices/0000\:81\:00.0/sriov_numvfs
- ./dpdk_nic_bind.py --st
+ ./usertools/dpdk-devbind.py -s
0000:81:00.0 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f0 drv=i40e
0000:81:02.0 'XL710/X710 Virtual Function' unused=
@@ -601,14 +611,14 @@ test Case 10: vf reset (two vfs passed through to two VM)
./tools/dpdk_nic_bind.py --bind=igb_uio 00:05.0
./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 \
- -- -i --crc-strip --eth-peer=0,vf1port_macaddr \
+ -- -i --eth-peer=0,vf1port_macaddr \
login vm1, got VF1 pci device id in vm1, assume it's 00:06.0,
bind the port to igb_uio, then start testpmd on vf1 port::
./tools/dpdk_nic_bind.py --bind=igb_uio 00:06.0
./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf0 -n 4 \
- -- -i --crc-strip
+ -- -i
5. Add vlan on vf0 in vm0, and set fwd mode::
@@ -632,7 +642,7 @@ test Case 10: vf reset (two vfs passed through to two VM)
vf0 can forward the packets to vf1.
7. Reset pf, don't reset vf0 and vf1, send the two packets,
- vf0 and vf1 cannot receive any packets.
+ vf0 can forward both of the two type packets to VF1.
8. Reset vf0 and vf1, send the two packets,
vf0 can forward both of the two type packets to VF1.
--
2.14.3
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [dts] [PATCH] test_plans: change some test parameters
2019-09-18 6:32 [dts] [PATCH] test_plans: change some test parameters Peng Yuan
@ 2019-09-20 6:48 ` Tu, Lijuan
0 siblings, 0 replies; 2+ messages in thread
From: Tu, Lijuan @ 2019-09-20 6:48 UTC (permalink / raw)
To: Peng, Yuan, dts; +Cc: Peng, Yuan
Applied, thanks
> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of Peng Yuan
> Sent: Wednesday, September 18, 2019 2:32 PM
> To: dts@dpdk.org
> Cc: Peng, Yuan <yuan.peng@intel.com>
> Subject: [dts] [PATCH] test_plans: change some test parameters
>
> From: pengyuan <yuan.peng@intel.com>
>
> Change some test parameters for vf_pf_reset_test_plan.rst
>
> Signed-off-by: pengyuan <yuan.peng@intel.com>
>
> diff --git a/test_plans/vf_pf_reset_test_plan.rst
> b/test_plans/vf_pf_reset_test_plan.rst
> index 7d526c8..51a3e3d 100644
> --- a/test_plans/vf_pf_reset_test_plan.rst
> +++ b/test_plans/vf_pf_reset_test_plan.rst
> @@ -1,4 +1,4 @@
> -.. Copyright (c) <2015-2017>, Intel Corporation
> +.. Copyright (c) <2015-2019>, Intel Corporation
> All rights reserved.
>
> Redistribution and use in source and binary forms, with or without @@ -
> 34,6 +34,7 @@ VF PF Reset Tests =================
>
> + The scenario is kernel PF + DPDK VF
>
> Prerequisites
> =============
> @@ -51,13 +52,18 @@ Prerequisites
> testpmd> port reset (port_id|all)
> "Reset all ports or port_id"
>
> +3. Enable pf private flags::
> +
> + ethtool --set-priv-flags ens5f0 link-down-on-close on
> + ethtool --set-priv-flags ens5f1 link-down-on-close on
> +
>
> Test Case 1: vf reset -- create two vfs on one pf
> =================================================
>
> -1. Got the pci device id of DUT, for example::
> +1. Get the pci device id of DUT, for example::
>
> - ./dpdk_nic_bind.py --st
> + ./usertools/dpdk-devbind.py -s
>
> 0000:81:00.0 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f0 drv=i40e
> 0000:81:00.1 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f1 drv=i40e
> @@ -65,7 +71,7 @@ Test Case 1: vf reset -- create two vfs on one pf 2.
> Create 2 VFs from 1 PF,and set the VF MAC address at PF0::
>
> echo 2 > /sys/bus/pci/devices/0000\:81\:00.0/sriov_numvfs
> - ./dpdk_nic_bind.py --st
> + ./usertools/dpdk-devbind.py -s
>
> 0000:81:00.0 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f0 drv=i40e
> 0000:81:02.0 'XL710/X710 Virtual Function' unused= @@ -75,7 +81,7 @@
> Test Case 1: vf reset -- create two vfs on one pf
>
> 3. Bind the VFs to dpdk driver::
>
> - ./tools/dpdk-devbind.py -b vfio-pci 81:02.0 81:02.1
> + ./usertools/dpdk-devbind.py -b vfio-pci 81:02.0 81:02.1
>
> 4. Set the VLAN id of VF1 and VF2::
>
> @@ -85,7 +91,7 @@ Test Case 1: vf reset -- create two vfs on one pf 5. Run
> testpmd::
>
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 -- -i \
> - --portmask=0x3 --tx-offloads=0x8fff --crc-strip
> + --portmask=0x3
> testpmd> set fwd mac
> testpmd> start
> testpmd> set allmulti all on
> @@ -95,7 +101,7 @@ Test Case 1: vf reset -- create two vfs on one pf
> Promiscuous mode: disabled
> Allmulticast mode: enabled
>
> - the status are not different from the default value.
> + The status are not different from the default value.
>
> 6. Get mac address of one VF and use it as dest mac, using scapy to
> send 1000 random packets from tester, verify the packets can be received
> @@ -105,21 +111,19 @@ Test Case 1: vf reset -- create two vfs on one pf
> >>>sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=1)/IP()/Raw('x'*40)
> ], \
> iface="ens3f0",count=1000)
>
> -7. Reset pf::
> -
> - ifconfig ens5f0 promisc
> +7. Set pf down::
>
> - or::
> + ifconfig ens5f0 down
>
> - ifconfig ens5f0 -promisc
> + Send the same 1000 packets with scapy from tester,
> + the vf cannot receive any packets, including vlan=0 and vlan=1
>
> -8. Vf receive a pf reset message::
> +8. Set pf up::
>
> - Event type: RESET interrupt on port 0
> - Event type: RESET interrupt on port 1
> + ifconfig ens5f0 up
>
> - if don't reset the vf, send the same 1000 packets with scapy from tester,
> - the vf cannot receive any packets, including vlan=0 and vlan=1
> + Send the same 1000 packets with scapy from tester, verify the packets can
> be
> + received by one VF and can be forward to another VF correctly.
>
> 9. Reset the vfs, run the command::
>
> @@ -128,8 +132,8 @@ Test Case 1: vf reset -- create two vfs on one pf
> testpmd> port reset 1
> testpmd> start
>
> - or just run the command "port reset all"
> - send the same 1000 packets with scapy from tester, verify the packets can
> be
> + or just run the command "port reset all".
> + Send the same 1000 packets with scapy from tester, verify the
> + packets can be
> received by one VF and can be forward to another VF correctly,
> check the port info::
>
> @@ -145,7 +149,8 @@ Test Case 1: vf reset -- create two vfs on one pf
> Promiscuous mode: disabled
> Allmulticast mode: enabled
>
> - the info status is consistent to the status before reset.
> + The info status is consistent to the status before reset.
> +
>
> Test Case 2: vf reset -- create two vfs on one pf, run testpmd separately
> ================================================================
> =========
> @@ -156,11 +161,11 @@ Test Case 2: vf reset -- create two vfs on one pf,
> run testpmd separately
>
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 \
> --socket-mem 1024,1024 -w 81:02.0 --file-prefix=test1 \
> - -- -i --crc-strip --eth-peer=0,00:11:22:33:44:12 \
> + -- -i --eth-peer=0,00:11:22:33:44:12 \
>
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf0 -n 4 \
> --socket-mem 1024,1024 -w 81:02.1 --file-prefix=test2 \
> - -- -i --crc-strip
> + -- -i
>
> 3. Set fwd mode on vf0::
>
> @@ -180,7 +185,7 @@ Test Case 2: vf reset -- create two vfs on one pf, run
> testpmd separately
> vf0 can forward the packets to vf1.
>
> 6. Reset pf, don't reset vf0 and vf1, send the packets,
> - vf0 and vf1 cannot receive any packets.
> + vf0 can forward the packet to vf1.
>
> 7. Reset vf0 and vf1, send the packets,
> vf0 can forward the packet to vf1.
> @@ -203,7 +208,7 @@ Test Case 3: vf reset -- create one vf on each pf 3.
> Start one testpmd on two vf ports::
>
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 -- -i \
> - --portmask=0x3 --tx-offloads=0x8fff --crc-strip
> + --portmask=0x3
>
> 4. Start forwarding::
>
> @@ -218,7 +223,7 @@ Test Case 3: vf reset -- create one vf on each pf
> vfs can fwd the packets normally.
>
> 6. Reset pf0 and pf1, don't reset vf0 and vf1, send the packets,
> - vfs cannot receive any packets.
> + vfs can fwd the packets normally.
>
> 7. Reset vf0 and vf1, send the packets,
> vfs can fwd the packets normally.
> @@ -230,7 +235,7 @@ Test Case 4: vlan rx restore -- vf reset all ports 1.
> Execute the step1-step3 of test case 1, then start the testpmd::
>
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 -- -i \
> - --portmask=0x3 --tx-offloads=0x8fff --crc-strip
> + --portmask=0x3
> testpmd> set fwd mac
>
> 2. Add vlan on both ports::
> @@ -239,7 +244,7 @@ Test Case 4: vlan rx restore -- vf reset all ports
> testpmd> rx_vlan add 1 1
> testpmd> start
>
> - send packets with scapy from tester::
> + Send packets with scapy from tester::
>
> sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \
> iface="ens3f0",count=1000)
> @@ -251,7 +256,7 @@ Test Case 4: vlan rx restore -- vf reset all ports
> iface="ens3f0",count=1000)
>
> vfs can receive the packets and forward it.
> - send packets with scapy from tester::
> + Send packets with scapy from tester::
>
> sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=2)/IP()/Raw('x'*1000)],
> \
> iface="ens3f0",count=1000)
> @@ -259,7 +264,7 @@ Test Case 4: vlan rx restore -- vf reset all ports
> vf0 cannot receive any packets.
>
> 3. Reset pf, don't reset vf, send the packets in step2 from tester,
> - the vfs cannot receive any packets.
> + vfs can receive the packets and forward it.
>
> 4. Reset both vfs::
>
> @@ -267,9 +272,9 @@ Test Case 4: vlan rx restore -- vf reset all ports
> testpmd> port reset all
> testpmd> start
>
> - send the packets in step2 from tester
> + Send the packets in step2 from tester,
> vfs can receive the packets and forward it.
> - send packets with scapy from tester::
> + Send packets with scapy from tester::
>
> sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=2)/IP()/Raw('x'*1000)],
> \
> iface="ens3f0",count=1000)
> @@ -283,7 +288,7 @@ test Case 5: vlan rx restore -- vf reset one port 1.
> Execute the step1-step3 of test case 1, then start the testpmd::
>
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 -- -i \
> - --portmask=0x3 --tx-offloads=0x8fff --crc-strip
> + --portmask=0x3
> testpmd> set fwd mac
>
> 2. Add vlan on both ports::
> @@ -292,7 +297,7 @@ test Case 5: vlan rx restore -- vf reset one port
> testpmd> rx_vlan add 1 1
> testpmd> start
>
> - send packets with scapy from tester::
> + Send packets with scapy from tester::
>
> sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \
> iface="ens3f0",count=1000)
> @@ -315,15 +320,15 @@ test Case 5: vlan rx restore -- vf reset one port
> sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=1)/IP()/Raw('x'*1000)],
> \
> iface="ens3f0",count=1000)
>
> - vf0 can receive the packets, but vf1 can't transmit the packets.
> - send packets from tester::
> + vfs can receive and forward the packets.
> + Send packets from tester::
>
> sendp([Ether(dst="00:11:22:33:44:12")/IP()/Raw('x'*1000)], \
> iface="ens3f0",count=1000)
> sendp([Ether(dst="00:11:22:33:44:12")/Dot1Q(vlan=1)/IP()/Raw('x'*1000)],
> \
> iface="ens3f0",count=1000)
>
> - vf1 cannot receive the packets.
> + vfs can receive and forward the packets.
>
> 4. Reset vf1::
>
> @@ -365,13 +370,13 @@ Test Case 6: vlan rx restore -- create one vf on each
> pf
> iface="ens3f0",count=1000)
>
> vfs can forward the packets normally.
> - send packets with scapy from tester::
> + Send packets with scapy from tester::
>
> sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=2)/IP()/Raw('x'*1000)],
> \
> iface="ens3f0",count=1000)
>
> vf0 cannot receive any packets.
> - remove vlan 0 on vf1::
> + Remove vlan 0 on vf1::
>
> testpmd> rx_vlan rm 0 1
> sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \ @@ -383,10
> +388,14 @@ Test Case 6: vlan rx restore -- create one vf on each pf
>
> sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*1000)], \
> iface="ens3f0",count=1000)
> +
> + vf0 can receive the packets, but vf1 can't transmit the packets.
> + Send packets from tester::
> +
> sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=1)/IP()/Raw('x'*1000)],
> \
> iface="ens3f0",count=1000)
>
> - the vfs cannot receive any packets.
> + vfs can forward the packets normally.
>
> 4. Reset both vfs, send packets from tester::
>
> @@ -397,7 +406,7 @@ Test Case 6: vlan rx restore -- create one vf on each
> pf
> iface="ens3f0",count=1000)
>
> vf0 can receive the packets, but vf1 can't transmit the packets.
> - send packets from tester::
> + Send packets from tester::
>
> sendp([Ether(dst="00:11:22:33:44:11")/Dot1Q(vlan=1)/IP()/Raw('x'*1000)],
> \
> iface="ens3f0",count=1000)
> @@ -413,9 +422,9 @@ Test Case 7: vlan tx restore 2. Run testpmd::
>
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 -- -i \
> - --portmask=0x3 --tx-offloads=0x8fff --crc-strip
> + --portmask=0x3
>
> -2. Add tx vlan offload on VF1 port, take care the first param is port,
> +3. Add tx vlan offload on VF1 port, take care the first param is port,
> start forwarding::
>
> testpmd> set fwd mac
> @@ -426,18 +435,18 @@ Test Case 7: vlan tx restore
> testpmd> tx_vlan set 1 51
> testpmd> start
>
> -3. Send packets with scapy from tester::
> +4. Send packets with scapy from tester::
>
> sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*18)], \
> iface="ens3f0",count=1)
>
> -4. Listening the port ens3f0::
> +5. Listening the port ens3f0::
>
> tcpdump -i ens3f0 -n -e -x -v
>
> check the packet received, the packet is configured with vlan 51
>
> -5. Reset the pf, then reset the two vfs,
> +6. Reset the pf, then reset the two vfs,
> send the same packet with no vlan tag,
> check packets received by tester, the packet is configured with vlan 51.
>
> @@ -457,7 +466,7 @@ test Case 8: MAC address restore 3. Start testpmd on
> two vf ports::
>
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 \
> - -- -i --portmask=0x3 --tx-offloads=0x8fff --crc-strip
> + -- -i --portmask=0x3
>
> 4. Add MAC address to the vf0 ports::
>
> @@ -466,6 +475,7 @@ test Case 8: MAC address restore
>
> 5. Start forwarding::
>
> + testpmd> set promisc all off
> testpmd> set fwd mac
> testpmd> start
>
> @@ -479,7 +489,7 @@ test Case 8: MAC address restore
> vfs can forward both of the two type packets.
>
> 7. Reset pf0 and pf1, don't reset vf0 and vf1, send the two packets,
> - vf0 and vf1 cannot receive any packets.
> + vfs can forward both of the two type packets.
>
> 8. Reset vf0 and vf1, send the two packets,
> vfs can forward both of the two type packets.
> @@ -491,7 +501,7 @@ test Case 9: vf reset (two vfs passed through to one
> VM) 1. Create 2 VFs from 1 PF,and set the VF MAC address at PF0::
>
> echo 2 > /sys/bus/pci/devices/0000\:81\:00.0/sriov_numvfs
> - ./dpdk_nic_bind.py --st
> + ./usertools/dpdk-devbind.py -s
>
> 0000:81:00.0 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f0 drv=i40e
> 0000:81:02.0 'XL710/X710 Virtual Function' unused= @@ -500,14 +510,14
> @@ test Case 9: vf reset (two vfs passed through to one VM) 2. Detach VFs
> from the host, bind them to pci-stub driver::
>
> modprobe pci-stub
> - ./tools/dpdk_nic_bind.py --bind=pci_stub 81:02.0 81:02.1
> + ./usertools/dpdk-devbind.py -b pci_stub 81:02.0 81:02.1
>
> or using the following way::
>
> virsh nodedev-detach pci_0000_81_02_0;
> virsh nodedev-detach pci_0000_81_02_1;
>
> - ./dpdk_nic_bind.py --st
> + ./usertools/dpdk-devbind.py -s
>
> 0000:81:00.0 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f0 drv=i40e
> 0000:81:02.0 'XL710/X710 Virtual Function' if= drv=pci-stub unused= @@
> -525,9 +535,9 @@ test Case 9: vf reset (two vfs passed through to one VM) 4.
> Login vm0, got VFs pci device id in vm0, assume they are 00:05.0 & 00:05.1,
> bind them to igb_uio driver,and then start testpmd::
>
> - ./tools/dpdk_nic_bind.py --bind=igb_uio 00:05.0 00:05.1
> + ./usertools/dpdk-devbind.py -b igb_uio 00:05.0 00:05.1
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0x0f -n 4 \
> - -w 00:05.0 -w 00:05.1 -- -i --portmask=0x3 --tx-offloads=0x8fff
> + -w 00:05.0 -w 00:05.1 -- -i --portmask=0x3
>
> 5. Add MAC address to the vf0 ports, set it in mac forward mode::
>
> @@ -546,7 +556,7 @@ test Case 9: vf reset (two vfs passed through to one
> VM)
> vfs can forward both of the two type packets.
>
> 7. Reset pf0 and pf1, don't reset vf0 and vf1, send the two packets,
> - vf0 and vf1 cannot receive any packets.
> + vfs can forward both of the two type packets.
>
> 8. Reset vf0 and vf1, send the two packets,
> vfs can forward both of the two type packets.
> @@ -558,7 +568,7 @@ test Case 10: vf reset (two vfs passed through to two
> VM) 1. Create 2 VFs from 1 PF,and set the VF MAC address at PF::
>
> echo 2 > /sys/bus/pci/devices/0000\:81\:00.0/sriov_numvfs
> - ./dpdk_nic_bind.py --st
> + ./usertools/dpdk-devbind.py -s
>
> 0000:81:00.0 'Ethernet Controller X710 for 10GbE SFP+' if=ens5f0 drv=i40e
> 0000:81:02.0 'XL710/X710 Virtual Function' unused= @@ -601,14 +611,14
> @@ test Case 10: vf reset (two vfs passed through to two VM)
>
> ./tools/dpdk_nic_bind.py --bind=igb_uio 00:05.0
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 \
> - -- -i --crc-strip --eth-peer=0,vf1port_macaddr \
> + -- -i --eth-peer=0,vf1port_macaddr \
>
> login vm1, got VF1 pci device id in vm1, assume it's 00:06.0,
> bind the port to igb_uio, then start testpmd on vf1 port::
>
> ./tools/dpdk_nic_bind.py --bind=igb_uio 00:06.0
> ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf0 -n 4 \
> - -- -i --crc-strip
> + -- -i
>
> 5. Add vlan on vf0 in vm0, and set fwd mode::
>
> @@ -632,7 +642,7 @@ test Case 10: vf reset (two vfs passed through to two
> VM)
> vf0 can forward the packets to vf1.
>
> 7. Reset pf, don't reset vf0 and vf1, send the two packets,
> - vf0 and vf1 cannot receive any packets.
> + vf0 can forward both of the two type packets to VF1.
>
> 8. Reset vf0 and vf1, send the two packets,
> vf0 can forward both of the two type packets to VF1.
> --
> 2.14.3
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2019-09-20 6:48 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-09-18 6:32 [dts] [PATCH] test_plans: change some test parameters Peng Yuan
2019-09-20 6:48 ` Tu, Lijuan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).