[dts] [PATCH V1 1/2] test_plans/rxtx_offload: add tx offload multi_segs setting

[Yu Jiang <yux.jiang@intel.com>]

add tx offload multi_segs setting

Signed-off-by: Yu Jiang <yux.jiang@intel.com>
---
 test_plans/rxtx_offload_test_plan.rst | 56 +++++++++++++++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/test_plans/rxtx_offload_test_plan.rst b/test_plans/rxtx_offload_test_plan.rst
index 246e1e1..962ee9f 100644
--- a/test_plans/rxtx_offload_test_plan.rst
+++ b/test_plans/rxtx_offload_test_plan.rst
@@ -677,3 +677,59 @@ Test case: FVL Tx offload per-queue setting
 
    Note 1: there is no tx_offload per_queue parameter in ixgbe driver,
    so this case is just only for i40e.
+
+Test case: Tx offload multi_segs setting
+======================================================
+
+1. Start testpmd with "--tx-offloads=0x00008000" to enable tx_offload multi_segs ::
+
+    ./testpmd -c 0xf -n 4  -- -i --tx-offloads==0x00008000
+    testpmd> show port 0 tx_offload configuration
+    Tx Offloading Configuration of port 0 :
+      Port : MULTI_SEGS
+      Queue[ 0] : MULTI_SEGS
+
+2. Set fwd to txonly, Set the length of each segment of the TX-ONLY packets, Set the split policy for TX packets, then start to send pkgs::
+
+    testpmd> set fwd txonly
+    testpmd> set txpkts 64,64
+    testpmd> set txsplit rand
+    testpmd> start
+
+3. Check TX-packets will not hang and continue to increase::
+    Wait 15s or more, check TX-packets will continue to increase and can be more than 300K
+
+    testpmd> show port stats all
+    testpmd> stop
+    testpmd> quit
+
+4. Start testpmd again without "--tx-offloads", check multi-segs is disabled by default::
+
+    ./testpmd -c 0xf -n 4  -- -i
+    testpmd> show port 0 tx_offload configuration
+    No MULTI_SEGS in Tx Offloading Configuration of ports
+
+5. Enable tx_offload multi_segs ::
+    testpmd> port stop all
+    testpmd> port config 0 tx_offload multi_segs on
+    testpmd> port config 1 tx_offload multi_segs on
+    testpmd> port start all
+    testpmd> show port 0 tx_offload configuration
+    Tx Offloading Configuration of port 0 :
+      Port : MULTI_SEGS
+      Queue[ 0] : MULTI_SEGS
+
+6. Set fwd to txonly, Set the length of each segment of the TX-ONLY packets, Set the split policy for TX packets, then start to send pkgs::
+
+    testpmd> set fwd txonly
+    testpmd> set txpkts 64,64
+    testpmd> set txsplit rand
+    testpmd> start
+    testpmd> show port stats all
+
+7. Check TX-packets will not hang and continue to increase::
+    Wait 15s or more, check TX-packets will continue to increase and can be more than 300K
+
+    testpmd> show port stats all
+    testpmd> stop
+    testpmd> quit
-- 
2.7.4