From: Yu Jiang <yux.jiang@intel.com>
To: dts@dpdk.org
Cc: Yu Jiang <yux.jiang@intel.com>
Subject: [dts] [PATCH V2 2/2] test_plans/rxtx_offload: add tx offload multi_segs setting plan
Date: Wed, 25 Aug 2021 11:11:48 +0800 [thread overview]
Message-ID: <1629861108-30497-3-git-send-email-yux.jiang@intel.com> (raw)
In-Reply-To: <1629861108-30497-1-git-send-email-yux.jiang@intel.com>
vector path doesn't support multi-segment packet transmit,
only normal path supports multi-segment packet transmit.
Use 'port config 0 tx_offload multi_segs on' or
"--tx-offloads=0x00008000" parameter to enable multi segment offload.
Signed-off-by: Yu Jiang <yux.jiang@intel.com>
---
test_plans/rxtx_offload_test_plan.rst | 99 +++++++++++++++++++++++++++++++++++
1 file changed, 99 insertions(+)
diff --git a/test_plans/rxtx_offload_test_plan.rst b/test_plans/rxtx_offload_test_plan.rst
index 246e1e1..d008d43 100644
--- a/test_plans/rxtx_offload_test_plan.rst
+++ b/test_plans/rxtx_offload_test_plan.rst
@@ -677,3 +677,102 @@ Test case: FVL Tx offload per-queue setting
Note 1: there is no tx_offload per_queue parameter in ixgbe driver,
so this case is just only for i40e.
+
+Test case: Tx offload multi_segs setting
+======================================================
+
+1. Start testpmd with "--tx-offloads=0x00008000" to enable tx_offload multi_segs ::
+
+ ./testpmd -c 0xf -n 4 -- -i --tx-offloads==0x00008000
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port : MULTI_SEGS
+ Queue[ 0] : MULTI_SEGS
+
+2. Set fwd to txonly, Set the length of each segment of the TX-ONLY packets, Set the split policy for TX packets, then start to send pkgs::
+
+ testpmd> set fwd txonly
+ testpmd> set txpkts 64,128,512,2000,64,128,512,2000
+ testpmd> set txsplit rand
+ testpmd> start
+
+3. Check TX-packets will not hang and continue to increase::
+ Wait 30s or more, check TX-packets will continue to increase and can be more than 100K
+
+ testpmd> show port stats all
+ ######################## NIC statistics for port 0 ########################
+ RX-packets: 0 RX-missed: 0 RX-bytes: 0
+ RX-errors: 0
+ RX-nombuf: 0
+ TX-packets: 102628493 TX-errors: 0 TX-bytes: 139709164375
+
+ Throughput (since last show)
+ Rx-pps: 0 Rx-bps: 0
+ Tx-pps: 563539 Tx-bps: 9892394768
+ ############################################################################
+
+ ######################## NIC statistics for port 1 ########################
+ RX-packets: 0 RX-missed: 0 RX-bytes: 0
+ RX-errors: 0
+ RX-nombuf: 0
+ TX-packets: 102627429 TX-errors: 0 TX-bytes: 139709724215
+
+ Throughput (since last show)
+ Rx-pps: 0 Rx-bps: 0
+ Tx-pps: 563708 Tx-bps: 9892375000
+ ############################################################################
+
+ testpmd> stop
+ testpmd> quit
+
+4. Start testpmd again without "--tx-offloads", check multi-segs is disabled by default::
+
+ ./testpmd -c 0xf -n 4 -- -i
+ testpmd> show port 0 tx_offload configuration
+ No MULTI_SEGS in Tx Offloading Configuration of ports
+
+5. Enable tx_offload multi_segs ::
+ testpmd> port stop all
+ testpmd> port config 0 tx_offload multi_segs on
+ testpmd> port config 1 tx_offload multi_segs on
+ testpmd> port start all
+ testpmd> show port 0 tx_offload configuration
+ Tx Offloading Configuration of port 0 :
+ Port : MULTI_SEGS
+ Queue[ 0] : MULTI_SEGS
+
+6. Set fwd to txonly, Set the length of each segment of the TX-ONLY packets, Set the split policy for TX packets, then start to send pkgs::
+
+ testpmd> set fwd txonly
+ testpmd> set txpkts 64,128,256,512,64,128,256,512
+ testpmd> set txsplit rand
+ testpmd> start
+
+7. Check TX-packets will not hang and continue to increase::
+ Wait 30s or more, check TX-packets will continue to increase and can be more than 100K
+
+ testpmd> show port stats all
+ ######################## NIC statistics for port 0 ########################
+ RX-packets: 0 RX-missed: 0 RX-bytes: 0
+ RX-errors: 0
+ RX-nombuf: 0
+ TX-packets: 101266875 TX-errors: 0 TX-bytes: 136721429135
+
+ Throughput (since last show)
+ Rx-pps: 0 Rx-bps: 0
+ Tx-pps: 563293 Tx-bps: 9892438256
+ ############################################################################
+
+ ######################## NIC statistics for port 1 ########################
+ RX-packets: 0 RX-missed: 0 RX-bytes: 0
+ RX-errors: 0
+ RX-nombuf: 0
+ TX-packets: 101265405 TX-errors: 0 TX-bytes: 136721996771
+
+ Throughput (since last show)
+ Rx-pps: 0 Rx-bps: 0
+ Tx-pps: 564392 Tx-bps: 9892193416
+ ############################################################################
+
+ testpmd> stop
+ testpmd> quit
--
2.7.4
next prev parent reply other threads:[~2021-08-25 3:12 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-25 3:11 [dts] [PATCH V2 0/2] rxtx_offload: add test plan and tests for tx offload multi_segs setting Yu Jiang
2021-08-25 3:11 ` [dts] [PATCH V2 1/2] tests/rxtx_offload: add tx offload multi_segs setting case Yu Jiang
2021-08-25 3:17 ` Jiang, YuX
2021-08-25 3:11 ` Yu Jiang [this message]
2021-08-27 8:25 ` [dts] [PATCH V2 0/2] rxtx_offload: add test plan and tests for tx offload multi_segs setting Tu, Lijuan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1629861108-30497-3-git-send-email-yux.jiang@intel.com \
--to=yux.jiang@intel.com \
--cc=dts@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).