* [dts] [PATCH] test_plans/loopback_multi_queues: add test plan for loopback multi-queues test
@ 2019-04-22 1:12 Yinan
0 siblings, 0 replies; only message in thread
From: Yinan @ 2019-04-22 1:12 UTC (permalink / raw)
To: dts; +Cc: Wang Yinan
From: Wang Yinan <yinan.wang@intel.com>
Signed-off-by: Wang Yinan <yinan.wang@intel.com>
---
.../loopback_multi_queues_test_plan.rst | 306 ++++++++++++++++++
1 file changed, 306 insertions(+)
create mode 100644 test_plans/loopback_multi_queues_test_plan.rst
diff --git a/test_plans/loopback_multi_queues_test_plan.rst b/test_plans/loopback_multi_queues_test_plan.rst
new file mode 100644
index 0000000..68fb61f
--- /dev/null
+++ b/test_plans/loopback_multi_queues_test_plan.rst
@@ -0,0 +1,306 @@
+.. Copyright (c) <2019>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary forim must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+=====================================================
+vhost/virtio-user loopback with multi-queue test plan
+=====================================================
+
+Description
+===========
+
+Benchmark vhost/virtio-user loopback multi-queues test with 8 rx/tx paths, virtio-user support 8 queues in maximum.
+Includes mergeable, normal, vector_rx, inorder mergeable,
+inorder no-mergeable, virtio 1.1 mergeable, virtio 1.1 inorder, virtio 1.1 normal path.
+
+Test Case 1: loopback 2 queues test with virtio 1.1 mergeable path
+==================================================================
+1. Launch testpmd by below command::
+
+ rm -rf vhost-net*
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --no-pci \
+ --vdev 'eth_vhost0,iface=vhost-net,queues=2' -- \
+ -i --nb-cores=2 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+ testpmd>set fwd mac
+
+2. Launch virtio-user by below command::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 \
+ --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,queues=2,packed_vq=1,mrg_rxbuf=1,in_order=0 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+ >set fwd mac
+ >start
+
+3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in [64, 128, 256, 512, 1024, 1518]::
+
+ testpmd>set txpkts [frame_size]
+ testpmd>start tx_first 32
+
+4. Get throughput 10 times and calculate the average throughput::
+
+ testpmd>show port stats all
+
+5. Check each queue's RX/TX packet numbers::
+
+ testpmd>stop
+
+Test Case 2: loopback 2 queues test with virtio 1.1 normal path
+===============================================================
+
+1. Launch testpmd by below command::
+
+ rm -rf vhost-net*
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --no-pci \
+ --vdev 'eth_vhost0,iface=vhost-net,queues=2' -- \
+ -i --nb-cores=2 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+ testpmd>set fwd mac
+
+2. Launch virtio-user by below command::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 \
+ --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,queues=2,packed_vq=1,mrg_rxbuf=0,in_order=0 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+ >set fwd mac
+ >start
+
+3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in [64, 128, 256, 512, 1024, 1518]::
+
+ testpmd>set txpkts [frame_size]
+ testpmd>start tx_first 32
+
+4. Get throughput 10 times and calculate the average throughput::
+
+ testpmd>show port stats all
+
+5. Check each queue's RX/TX packet numbers::
+
+ testpmd>stop
+
+Test Case 3: loopback 2 queues test with virtio 1.1 inorder path
+================================================================
+
+1. Launch testpmd by below command::
+
+ rm -rf vhost-net*
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --no-pci \
+ --vdev 'eth_vhost0,iface=vhost-net,queues=2' -- \
+ -i --nb-cores=2 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+ testpmd>set fwd mac
+
+2. Launch virtio-user by below command::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 \
+ --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,queues=2,packed_vq=1,mrg_rxbuf=0,in_order=1 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+ >set fwd mac
+ >start
+
+3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in [64, 128, 256, 512, 1024, 1518]::
+
+ testpmd>set txpkts [frame_size]
+ testpmd>start tx_first 32
+
+4. Get throughput 10 times and calculate the average throughput::
+
+ testpmd>show port stats all
+
+5. Check each queue's RX/TX packet numbers::
+
+ testpmd>stop
+
+Test Case 4: loopback 2 queues test with inorder mergeable path
+===============================================================
+
+1. Launch testpmd by below command::
+
+ rm -rf vhost-net*
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --no-pci \
+ --vdev 'eth_vhost0,iface=vhost-net,queues=2' -- \
+ -i --nb-cores=2 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+ testpmd>set fwd mac
+
+2. Launch virtio-user by below command::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 \
+ --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,queues=2,in_order=1,mrg_rxbuf=1 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+ >set fwd mac
+ >start
+
+3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in [64, 128, 256, 512, 1024, 1518]::
+
+ testpmd>set txpkts [frame_size]
+ testpmd>start tx_first 32
+
+4. Get throughput 10 times and calculate the average throughput::
+
+ testpmd>show port stats all
+
+5. Check each queue's RX/TX packet numbers::
+
+ testpmd>stop
+
+Test Case 5: loopback 2 queues test with inorder no-mergeable path
+==================================================================
+
+1. Launch testpmd by below command::
+
+ rm -rf vhost-net*
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --no-pci \
+ --vdev 'eth_vhost0,iface=vhost-net,queues=2' -- \
+ -i --nb-cores=2 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+ testpmd>set fwd mac
+
+2. Launch virtio-user by below command::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 \
+ --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,queues=2,in_order=1,mrg_rxbuf=0 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2 --txd=1024 --rxd=1024
+ >set fwd mac
+ >start
+
+3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in [64, 128, 256, 512, 1024, 1518]::
+
+ testpmd>set txpkts [frame_size]
+ testpmd>start tx_first 32
+
+4. Get throughput 10 times and calculate the average throughput::
+
+ testpmd>show port stats all
+
+5. Check each queue's RX/TX packet numbers::
+
+ testpmd>stop
+
+Test Case 6: loopback 8 queues test with mergeable path
+=======================================================
+
+1. Launch testpmd by below command::
+
+ rm -rf vhost-net*
+ ./testpmd -l 2-6 -n 4 --socket-mem 1024,1024 --no-pci \
+ --vdev 'eth_vhost0,iface=vhost-net,queues=8' -- \
+ -i --nb-cores=4 --rxq=8 --txq=8 --txd=1024 --rxd=1024
+ testpmd>set fwd mac
+
+2. Launch virtio-user by below command::
+
+ ./testpmd -n 4 -l 7-11 --socket-mem 1024,1024 \
+ --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,queues=8,in_order=0,mrg_rxbuf=1 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=4--rxq=8 --txq=8 --txd=1024 --rxd=1024
+ >set fwd mac
+ >start
+
+3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in [64, 128, 256, 512, 1024, 1518]::
+
+ testpmd>set txpkts [frame_size]
+ testpmd>start tx_first 32
+
+4. Get throughput 10 times and calculate the average throughput::
+
+ testpmd>show port stats all
+
+5. Check each queue's RX/TX packet numbers::
+
+ testpmd>stop
+
+
+Test Case 7: loopback 8 queues test with normal path
+====================================================
+
+1. Launch vhost by below command::
+
+ rm -rf vhost-net*
+ ./testpmd -n 4 -l 2-6 --socket-mem 1024,1024 --legacy-mem --no-pci \
+ --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net,queues=8' -- \
+ -i --nb-cores=4 --rxq=8 --txq=8 --txd=1024 --rxd=1024
+ >set fwd mac
+
+2. Launch virtio-user by below command::
+
+ ./testpmd -n 4 -l 7-11 --socket-mem 1024,1024 \
+ --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,queues=8,in_order=0,mrg_rxbuf=0 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=4 --rxq=8 --txq=8 --txd=1024 --rxd=1024
+ >set fwd mac
+ >start
+
+3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in [64, 128, 256, 512, 1024, 1518]::
+
+ testpmd>set txpkts [frame_size]
+ testpmd>start tx_first 32
+
+4. Get throughput 10 times and calculate the average throughput::
+
+ testpmd>show port stats all
+
+5. Check each queue's RX/TX packet numbers::
+
+ testpmd>stop
+
+Test Case 8: loopback 8 queues test with vector_rx path
+=======================================================
+
+1. Launch vhost by below command::
+
+ rm -rf vhost-net*
+ ./testpmd -n 4 -l 2-6 --socket-mem 1024,1024 --legacy-mem --no-pci \
+ --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net,queues=8' -- \
+ -i --nb-cores=4 --rxq=8 --txq=8 --txd=1024 --rxd=1024
+ >set fwd mac
+
+2. Launch virtio-user by below command::
+
+ ./testpmd -n 4 -l 7-11 --socket-mem 1024,1024 \
+ --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,queues=8,in_order=0,mrg_rxbuf=0 \
+ -- -i --tx-offloads=0x0 --rss-ip --nb-cores=4 --rxq=8 --txq=8 --txd=1024 --rxd=1024
+ >set fwd mac
+ >start
+
+3. Send packets with vhost-testpmd,[frame_size] is the parameter changs in [64, 128, 256, 512, 1024, 1518]::
+
+ testpmd>set txpkts [frame_size]
+ testpmd>start tx_first 32
+
+4. Get throughput 10 times and calculate the average throughput::
+
+ testpmd>show port stats all
+
+5. Check each queue's RX/TX packet numbers::
+
+ testpmd>stop
--
2.17.1
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2019-04-22 8:14 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-04-22 1:12 [dts] [PATCH] test_plans/loopback_multi_queues: add test plan for loopback multi-queues test Yinan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).