* [dts] [PATCH v1] test_plans: support fixed link speed in drivers
@ 2019-12-03 17:36 Guinan Sun
0 siblings, 0 replies; only message in thread
From: Guinan Sun @ 2019-12-03 17:36 UTC (permalink / raw)
To: dts; +Cc: Guinan Sun
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain; charset=y, Size: 11606 bytes --]
Signed-off-by: Guinan Sun <guinanx.sun@intel.com>
---
..._fixed_link_speed_in_drivers_test_plan.rst | 323 ++++++++++++++++++
1 file changed, 323 insertions(+)
create mode 100644 test_plans/support_fixed_link_speed_in_drivers_test_plan.rst
diff --git a/test_plans/support_fixed_link_speed_in_drivers_test_plan.rst b/test_plans/support_fixed_link_speed_in_drivers_test_plan.rst
new file mode 100644
index 0000000..e26f8f1
--- /dev/null
+++ b/test_plans/support_fixed_link_speed_in_drivers_test_plan.rst
@@ -0,0 +1,323 @@
+.. Copyright (c) <2019>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+
+=============================================
+Port Config Fixed Link Speed in drivers Tests
+=============================================
+
+Description
+===========
+Test whether support fixed link speed in drivers and "port config speed" command works properly.
+Setting exact link speed makes sense if auto-negotiation is disabled. Fixed flag is required
+to disable auto-negotiation.
+
+Prerequisites
+=============
+
+1. Hardware::
+ NIC driver driverversion firmware speed(MB)
+ I350 igb 5.4.0-k 1.63, 0x800009fa 10half/10/100half/100/1000
+ X722 i40e 2.1.14-k 3.31 0x80000d31 1.1767.0 1000/10000
+ X710 i40e 2.1.14-k 3.31 0x80000d31 1.1767.0 1000/10000
+ X550T ixgbe 5.1.0-k 0x61bf0001 100/1000/10000
+ X520(82599) ixgbe 5.1.0-k 0x61bf0001 10000
+ E810-XXVDA2 ice 0.12.25 1.00 0x80001e61 1.2535.0 1000/10000/25000
+
+2. linkage::
+ link two ports of every NIC.
+ example: (i350_port0 Active<--->i350_port1(dpdk); E810_port0 Active<--->E810_port1(dpdk) etc.)
+
+3. Modify/Unmodify the testpmd code as following for the test::
+
+ --- a/app/test-pmd/cmdline.c
+ +++ b/app/test-pmd/cmdline.c
+ @@ -1597,17 +1597,17 @@ parse_and_check_speed_duplex(char *speedstr, char *duplexstr, uint32_t *speed)
+ return -1;
+ }
+ if (!strcmp(speedstr, "1000")) {
+ - *speed = ETH_LINK_SPEED_1G;
+ + *speed = ETH_LINK_SPEED_1G | ETH_LINK_SPEED_FIXED;
+ } else if (!strcmp(speedstr, "10000")) {
+ - *speed = ETH_LINK_SPEED_10G;
+ + *speed = ETH_LINK_SPEED_10G | ETH_LINK_SPEED_FIXED;
+ } else if (!strcmp(speedstr, "25000")) {
+ - *speed = ETH_LINK_SPEED_25G;
+ + *speed = ETH_LINK_SPEED_25G | ETH_LINK_SPEED_FIXED;
+ } else if (!strcmp(speedstr, "40000")) {
+ - *speed = ETH_LINK_SPEED_40G;
+ + *speed = ETH_LINK_SPEED_40G | ETH_LINK_SPEED_FIXED;
+ } else if (!strcmp(speedstr, "50000")) {
+ - *speed = ETH_LINK_SPEED_50G;
+ + *speed = ETH_LINK_SPEED_50G | ETH_LINK_SPEED_FIXED;
+ } else if (!strcmp(speedstr, "100000")) {
+ - *speed = ETH_LINK_SPEED_100G;
+ + *speed = ETH_LINK_SPEED_100G | ETH_LINK_SPEED_FIXED;
+ } else if (!strcmp(speedstr, "auto")) {
+ *speed = ETH_LINK_SPEED_AUTONEG;
+ } else {
+
+Test Case: I350 port config
+=============================
+
+Run testpmd::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -l 0-3 -n 4 -- -i
+
+1. set link speed to 10 MB half-duplex, verify link speed::
+
+ testpmd> port stop all
+ testpmd> port config 0 speed 10 duplex half
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 10 Mbps
+ Link duplex: half-duplex
+2. set link speed to 10 MB full-duplex, verify link speed::
+
+ testpmd> port stop all
+ testpmd> port config 0 speed 10 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 10 Mbps
+ Link duplex: full-duplex
+3. set link speed to 100 MB half-duplex, verify link speed::
+
+ testpmd> port stop all
+ testpmd> port config 0 speed 100 duplex half
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 100 Mbps
+ Link duplex: half-duplex
+4. set link speed to 100 MB full-duplex, verify link speed::
+
+ testpmd> port stop all
+ testpmd> port config 0 speed 100 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 100 Mbps
+ Link duplex: full-duplex
+5. set link speed to 1000 MB full-duplex, verify link speed::
+
+ testpmd> port stop all
+ testpmd> port config 0 speed 1000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 1000 Mbps
+ Link duplex: full-duplex
+
+Test Case: x722 port config
+=============================
+
+Run testpmd::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -l 0-3 -n 4 -- -i
+
+1. set link speed to 1000 MB full-duplex, verify link speed::
+
+ testpmd> port stop all
+ testpmd> port config 0 speed 1000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 1000 Mbps
+ Link duplex: full-duplex
+
+2. set link speed to 10000 MB full-duplex, verify link speed::
+ testpmd> port stop all
+ testpmd> port config 0 speed 10000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 10000 Mbps
+ Link duplex: full-duplex
+
+Test Case: x710 port config
+=============================
+
+Run testpmd::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -l 0-3 -n 4 -- -i
+
+1. set link speed to 1000 MB full-duplex, verify link speed::
+ testpmd> port stop all
+ testpmd> port config 0 speed 1000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 1000 Mbps
+ Link duplex: full-duplex
+
+2. set link speed to 10000 MB full-duplex, verify link speed::
+ testpmd> port stop all
+ testpmd> port config 0 speed 10000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 10000 Mbps
+ Link duplex: full-duplex
+
+Test Case: X550T port config
+============================
+
+Run testpmd::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -l 0-3 -n 4 -- -i
+
+1. set link speed to 100 MB full-duplex, verify link speed::
+ testpmd> port stop all
+ testpmd> port config 0 speed 100 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 100 Mbps
+ Link duplex: full-duplex
+
+2. set link speed to 1000 MB full-duplex, verify link speed::
+ testpmd> port stop all
+ testpmd> port config 0 speed 1000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 1000 Mbps
+ Link duplex: full-duplex
+
+3. set link speed to 10000 MB full-duplex, verify link speed::
+ testpmd> port stop all
+ testpmd> port config 0 speed 10000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info all
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 10000 Mbps
+ Link duplex: full-duplex
+
+Test Case: X520(82599) port config
+===================================
+
+Run testpmd::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -l 0-3 -n 4 -- -i
+
+1. set link speed to 10000 MB full-duplex, verify link speed::
+ testpmd> port stop all
+ testpmd> port config 0 speed 10000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 10000 Mbps
+ Link duplex: full-duplex
+
+Test Case: E810-XXVDA2 port config
+===================================
+
+Run testpmd::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -l 0-3 -n 4 -- -i
+
+1. set link speed to 1000 MB full-duplex, verify link speed::
+ testpmd> port stop all
+ testpmd> port config 0 speed 1000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 1000 Mbps
+ Link duplex: full-duplex
+
+2. set link speed to 10000 MB full-duplex, verify link speed::
+ testpmd> port stop all
+ testpmd> port config 0 speed 10000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 10000 Mbps
+ Link duplex: full-duplex
+
+3. set link speed to 25000 MB full-duplex, verify link speed::
+ testpmd> port stop all
+ testpmd> port config 0 speed 25000 duplex full
+ testpmd> port start all
+ Port 0: link state change event
+ testpmd> show port info 0
+ Verify Result::
+ ********************* Infos for port 0 *********************
+ Link status: up
+ Link speed: 25000 Mbps
+ Link duplex: full-duplex
--
2.17.1
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2019-12-03 9:37 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-03 17:36 [dts] [PATCH v1] test_plans: support fixed link speed in drivers Guinan Sun
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).