test suite reviews and discussions
 help / color / mirror / Atom feed
* [dts] [PATCH V1] test_plans: add test plan port controls
@ 2019-12-06 15:56 Nannan Lu
  2019-12-19  7:54 ` Tu, Lijuan
  0 siblings, 1 reply; 2+ messages in thread
From: Nannan Lu @ 2019-12-06 15:56 UTC (permalink / raw)
  To: dts; +Cc: Nannan Lu

Signed-off-by: Nannan Lu <nannan.lu@intel.com>
---
 test_plans/port_control_test_plan.rst | 257 ++++++++++++++++++++++++++
 1 file changed, 257 insertions(+)
 create mode 100644 test_plans/port_control_test_plan.rst

diff --git a/test_plans/port_control_test_plan.rst b/test_plans/port_control_test_plan.rst
new file mode 100644
index 0000000..2fca8fd
--- /dev/null
+++ b/test_plans/port_control_test_plan.rst
@@ -0,0 +1,257 @@
+.. Copyright (c) <2019>, Intel Corporation
+   All rights reserved.
+
+   Redistribution and use in source and binary forms, with or without
+   modification, are permitted provided that the following conditions
+   are met:
+
+   - Redistributions of source code must retain the above copyright
+     notice, this list of conditions and the following disclaimer.
+
+   - Redistributions in binary form must reproduce the above copyright
+     notice, this list of conditions and the following disclaimer in
+     the documentation and/or other materials provided with the
+     distribution.
+
+   - Neither the name of Intel Corporation nor the names of its
+     contributors may be used to endorse or promote products derived
+     from this software without specific prior written permission.
+
+   THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+   "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+   LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+   FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+   COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+   INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+   (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+   SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+   HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+   STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+   ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+   OF THE POSSIBILITY OF SUCH DAMAGE.
+
+==================
+Port Control Tests
+==================
+
+
+Prerequisites
+=============
+
+1. Hardware:
+
+   * Fortville
+   * Niantic
+   * Columbiaville
+   * i350 NIC
+   * e1000 emulated device
+
+
+Test Case: pf start/stop/reset/close
+====================================
+
+1. Bind the port to dpdk driver::
+
+     ./usertools/dpdk-devbind.py -b igb_uio 18:00.2
+
+2. Run testpmd::
+
+     ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xff -n 4 -- -i
+
+     testpmd> set fwd mac
+     testpmd> start
+
+   check port info::
+
+     testpmd> show port info all
+
+     ********************* Infos for port 0  *********************
+     Link status: up
+     Link speed: 1000 Mbps
+
+   verify that the link status is up.
+
+   Using scapy to send 1000 random packets from tester,
+   verify the packets can be received and can be forwarded::
+
+     scapy
+     >>>sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*40)], \
+     iface="enp27s0f2",count=1000)
+
+3. Stop and start port::
+
+     testpmd> stop
+     testpmd> port stop all
+     testpmd> show port info all
+
+     ********************* Infos for port 0  *********************
+     Link status: down
+     Link speed: 0 Mbps
+
+  verify that the link status is down.
+
+  Then start the port::
+
+    testpmd> port start all
+    testpmd> start
+
+  check port info::
+
+    testpmd> show port info all
+
+    ********************* Infos for port 0  *********************
+    Link status: up
+    Link speed: 10000 Mbps
+
+  verify that the link status is up.
+
+  Send the same 1000 packets with scapy from tester,
+  verify the packets can be received and forwarded.
+
+4. Reset the port, run the commands::
+
+     testpmd> stop
+     testpmd> port stop all
+     testpmd> port reset all
+     testpmd> show port info all
+
+     ********************* Infos for port 0  *********************
+     Link status: down
+     Link speed: 0 Mbps
+
+   verify that the link status is down.
+
+   Then start the port::
+
+     testpmd> port start all
+     testpmd> start
+
+   check port info::
+
+     testpmd> show port info all
+
+     ********************* Infos for port 0  *********************
+     Link status: up
+     Link speed: 10000 Mbps
+
+   verify that the link status is up.
+   Send the same 1000 packets with scapy from tester,
+   verify the packets can be received and forwarded.
+
+5. Close the port, run the commands::
+
+     testpmd> stop
+     testpmd> port stop all
+     testpmd> port close all
+
+   check the port info::
+
+     testpmd> show port info all
+     testpmd>
+
+   verify that there is no output after executing this command.
+
+
+Test Case: e1000 emulated device start/stop/reset/close
+=======================================================
+
+1. Set up qemu environment
+
+   Virtual an e1000 emulated device in vm, then start
+   vm with the following command::
+
+     qemu-system-x86_64 -enable-kvm -m 16G -vnc :20 \
+     -smp cores=10,sockets=1 -cpu host -hda ./u18.img \
+     -device e1000,netdev=net1,mac=00:01:02:33:44:22 \
+     -netdev user,id=net1,hostfwd=tcp:10.67.119.144:6666-:22 \
+     -device e1000,netdev=net2,mac=00:01:02:33:44:33 \
+     -netdev user,id=net2,hostfwd=tcp:10.67.119.144:7777-:23 \
+     -monitor stdio
+
+   Login vm, get the pci device id of the e1000 emulated device,
+   assume it is 0000:00:03.0, bind it to igb_uio driver, and then
+   start testpmd::
+
+     ./usertools/dpdk-devbind.py -b igb_uio 0000:00:03.0
+     ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -- -i
+
+     testpmd-> set fwd mac
+     testpmd-> start
+
+   check port info::
+
+     testpmd> show port info all
+
+     ********************* Infos for port 0  *********************
+     Link status: up
+     Link speed: 1000 Mbps
+
+   verify that the link status is up.
+
+2. Stop and start port (not support)::
+
+     testpmd> stop
+     testpmd> port stop all
+     testpmd> show port info all
+
+     ********************* Infos for port 0  *********************
+     Link status: down
+     Link speed: 0 Mbps
+
+   verify that the link status is down.
+
+   Then start the port::
+
+     testmd-> port start all
+     testpmd> start
+
+   check the port info::
+
+      testpmd> show port info all
+
+      ********************* Infos for port 0  *********************
+      Link status: up
+      Link speed: 10000 Mbps
+
+   verify that the link status is up.
+
+3. Reset the port (not support)::
+
+     testpmd> stop
+     testpmd> port stop all
+     testpmd> port reset all
+     testpmd> show port info all
+
+     ********************* Infos for port 0  *********************
+     Link status: down
+     Link speed: 0 Mbps
+
+   verify that the link status is down.
+
+   Then start the port::
+
+     testpmd> port start all
+     testpmd> start
+
+   check the port info::
+
+      testpmd> show port info all
+
+      ********************* Infos for port 0  *********************
+      Link status: up
+      Link speed: 10000 Mbps
+
+   verify that the link status is up.
+
+4. Close the port::
+
+     testpmd> stop
+     testpmd> port stop all
+     testpmd> port close all
+
+   check the port info::
+
+     testpmd> show port info all
+     testpmd>
+
+   verify that there is no output after executing this command.
-- 
2.17.1


^ permalink raw reply	[flat|nested] 2+ messages in thread
end of thread, other threads:[~2019-12-19  7:55 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-06 15:56 [dts] [PATCH V1] test_plans: add test plan port controls Nannan Lu
2019-12-19  7:54 ` Tu, Lijuan

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).