From: Yinan <yinan.wang@intel.com>
To: dts@dpdk.org
Cc: Wang Yinan <yinan.wang@intel.com>
Subject: [dts] [PATCH v1] test_plans: add packed virtqueue test with loopback virtio-user cases
Date: Sun, 29 Dec 2019 17:22:41 +0000 [thread overview]
Message-ID: <20191229172241.25131-1-yinan.wang@intel.com> (raw)
From: Wang Yinan <yinan.wang@intel.com>
Add packed virtqueue server mode in loopback_virtio_user_packed_ring_server_mode_test_plan.rst
Signed-off-by: Wang Yinan <yinan.wang@intel.com>
---
...user_packed_ring_server_mode_test_plan.rst | 348 ++++++++++++++++++
1 file changed, 348 insertions(+)
create mode 100644 test_plans/loopback_virtio_user_packed_ring_server_mode_test_plan.rst
diff --git a/test_plans/loopback_virtio_user_packed_ring_server_mode_test_plan.rst b/test_plans/loopback_virtio_user_packed_ring_server_mode_test_plan.rst
new file mode 100644
index 0000000..ec9230d
--- /dev/null
+++ b/test_plans/loopback_virtio_user_packed_ring_server_mode_test_plan.rst
@@ -0,0 +1,348 @@
+.. Copyright (c) <2019>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOgit T LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+==========================================
+Packed ring loopback server mode test plan
+==========================================
+
+Virtio-user server mode is a feature to enable virtio-user as the server, vhost as the client, thus after vhost-user is killed then relaunched,
+virtio-user can reconnect back to vhost-user again; at another hand, virtio-user also can reconnect back to vhost-user after virtio-user is killed.This feature test need cover different rx/tx paths with virtio 1.0 and virtio 1.1, includes virtio 1.0 mergeable, normal, vector_rx, inorder no-mergeable, inorder mergeable path and virtio 1.1 mergeable, non-mergeable, inorder mergeable and inorder non-mergeable path.
+
+
+Test Case 1: Basic test for virtio-user server mode, launch virtio-user first
+=============================================================================
+
+1. Launch virtio-user as server mode::
+
+ ./testpmd -l 1-2 -n 4 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:11:22:33:44:10,path=/tmp/sock0,server=1,queues=1,packed_vq=1 -- -i --rxq=1 --txq=1 --no-numa
+ >set fwd mac
+ >start
+
+2. Launch vhost as client mode::
+
+ ./testpmd -l 3-4 -n 4 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=vhost \
+ --vdev 'net_vhost0,iface=/tmp/sock0,client=1,queues=1' -- -i --rxq=1 --txq=1 --nb-cores=1
+ >set fwd mac
+ >start tx_first 32
+
+3. Run below command to get throughput,verify the loopback throughput is not zero::
+
+ testpmd>show port stats all
+
+Test Case 2: loopback reconnect test with virtio 1.1 mergeable path and server mode
+===================================================================================
+
+1. launch vhost as client mode with 2 queues::
+
+ rm -rf vhost-net*
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=vhost \
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start
+
+2. Launch virtio-user as server mode with 2 queues::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=1,in_order=0 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+3. Quit vhost side testpmd, check the virtio-user side link status::
+
+ testpmd> show port info 0
+ #it should show "down"
+
+4. Relaunch vhost and send packets::
+
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=vhost \
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+
+ testpmd> show port info 0
+ #it should show up"
+ testpmd>show port stats all
+
+6. Check each RX/TX queue has packets::
+
+ testpmd>stop
+
+7. Quit virtio-user side testpmd, check the vhost side link status::
+
+ testpmd> show port info 0
+ #it should show "down"
+
+8. Relaunch virtio-user and send packets::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=1,in_order=0 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+
+ testpmd> show port info 0
+ #it should show up"
+ testpmd>show port stats all
+
+10. Port restart at vhost side by below command and re-calculate the average throughput::
+
+ testpmd>stop
+ testpmd>port stop 0
+ testpmd>port start 0
+ testpmd>start tx_first 32
+ testpmd>show port stats all
+
+11. Check each RX/TX queue has packets::
+
+ testpmd>stop
+
+Test Case 3: loopback reconnect test with virtio 1.1 non-mergeable path and server mode
+=======================================================================================
+
+1. launch vhost as client mode with 2 queues::
+
+ rm -rf vhost-net*
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=vhost \
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start
+
+2. Launch virtio-user as server mode with 2 queues::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=0,in_order=0 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+3. Quit vhost side testpmd, check the virtio-user side link status::
+
+ testpmd> show port info 0
+ #it should show "down"
+
+4. Relaunch vhost and send packets::
+
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=vhost \
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+
+ testpmd> show port info 0
+ #it should show up"
+ testpmd>show port stats all
+
+6. Check each RX/TX queue has packets::
+
+ testpmd>stop
+
+7. Quit virtio-user side testpmd, check the vhost side link status::
+
+ testpmd> show port info 0
+ #it should show "down"
+
+8. Relaunch virtio-user and send packets::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=0,in_order=0 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+
+ testpmd> show port info 0
+ #it should show up"
+ testpmd>show port stats all
+
+10. Port restart at vhost side by below command and re-calculate the average throughput::
+
+ testpmd>stop
+ testpmd>port stop 0
+ testpmd>port start 0
+ testpmd>start tx_first 32
+ testpmd>show port stats all
+
+11. Check each RX/TX queue has packets::
+
+ testpmd>stop
+
+Test Case 4: loopback reconnect test with virtio 1.1 inorder mergeable path and server mode
+===========================================================================================
+
+1. launch vhost as client mode with 2 queues::
+
+ rm -rf vhost-net*
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=vhost \
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start
+
+2. Launch virtio-user as server mode with 2 queues::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=1,in_order=1 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+3. Quit vhost side testpmd, check the virtio-user side link status::
+
+ testpmd> show port info 0
+ #it should show "down"
+
+4. Relaunch vhost and send packets::
+
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=vhost \
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+
+ testpmd> show port info 0
+ #it should show up"
+ testpmd>show port stats all
+
+6. Check each RX/TX queue has packets::
+
+ testpmd>stop
+
+7. Quit virtio-user side testpmd, check the vhost side link status::
+
+ testpmd> show port info 0
+ #it should show "down"
+
+8. Relaunch virtio-user and send packets::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=1,in_order=1 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+
+ testpmd> show port info 0
+ #it should show up"
+ testpmd>show port stats all
+
+10. Port restart at vhost side by below command and re-calculate the average throughput::
+
+ testpmd>stop
+ testpmd>port stop 0
+ testpmd>port start 0
+ testpmd>start tx_first 32
+ testpmd>show port stats all
+
+11. Check each RX/TX queue has packets::
+
+ testpmd>stop
+
+Test Case 5: loopback reconnect test with virtio 1.1 inorder non-mergeable path and server mode
+===============================================================================================
+
+1. launch vhost as client mode with 2 queues::
+
+ rm -rf vhost-net*
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=vhost \
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start
+
+2. Launch virtio-user as server mode with 2 queues::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=0,in_order=1 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+3. Quit vhost side testpmd, check the virtio-user side link status::
+
+ testpmd> show port info 0
+ #it should show "down"
+
+4. Relaunch vhost and send packets::
+
+ ./testpmd -c 0xe -n 4 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=vhost \
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+
+ testpmd> show port info 0
+ #it should show up"
+ testpmd>show port stats all
+
+6. Check each RX/TX queue has packets::
+
+ testpmd>stop
+
+7. Quit virtio-user side testpmd, check the vhost side link status::
+
+ testpmd> show port info 0
+ #it should show "down"
+
+8. Relaunch virtio-user and send packets::
+
+ ./testpmd -n 4 -l 5-7 --socket-mem 1024,1024 --legacy-mem --no-pci --file-prefix=virtio \
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=0,in_order=1 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ >set fwd mac
+ >start tx_first 32
+
+9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+
+ testpmd> show port info 0
+ #it should show up"
+ testpmd>show port stats all
+
+10. Port restart at vhost side by below command and re-calculate the average throughput::
+
+ testpmd>stop
+ testpmd>port stop 0
+ testpmd>port start 0
+ testpmd>start tx_first 32
+ testpmd>show port stats all
+
+11. Check each RX/TX queue has packets::
+
+ testpmd>stop
--
2.17.1
next reply other threads:[~2019-12-30 0:27 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-29 17:22 Yinan [this message]
2020-01-02 3:30 ` Tu, Lijuan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191229172241.25131-1-yinan.wang@intel.com \
--to=yinan.wang@intel.com \
--cc=dts@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).