* [dts] [PATCH] speed-capabilities: Added Speed Capabilities test case
@ 2020-06-29 20:09 dkirichok
0 siblings, 0 replies; 5+ messages in thread
From: dkirichok @ 2020-06-29 20:09 UTC (permalink / raw)
To: dts
Cc: mb, lylavoie, thomas, dev, david.marchand, ferruh.yigit,
arybchenko, i.dyukov, rasland, j.hendergart, ohilyard,
Daniel Kirichok
From: Daniel Kirichok <dkirichok@iol.unh.edu>
Added Speed Capabilities test which compares detected interface speeds with what is expected in the config file.
Signed-off-by: Daniel Kirichok <dkirichok@iol.unh.edu>
---
conf/speed_capabilities.cfg | 4 +
test_plans/speed_capabilities_test_plan.rst | 84 ++++++++++++++
tests/TestSuite_speed_capabilities.py | 120 ++++++++++++++++++++
3 files changed, 208 insertions(+)
create mode 100644 conf/speed_capabilities.cfg
create mode 100644 test_plans/speed_capabilities_test_plan.rst
create mode 100644 tests/TestSuite_speed_capabilities.py
diff --git a/conf/speed_capabilities.cfg b/conf/speed_capabilities.cfg
new file mode 100644
index 0000000..c22f531
--- /dev/null
+++ b/conf/speed_capabilities.cfg
@@ -0,0 +1,4 @@
+[suite]
+# The format for entering expected speeds is {'<INTERFACE>':'<EXPECTED SPEED>',...}
+# Unit for speed must be in G or M
+expected_speeds={'interface1': '10G', 'interface2': '100M'}
diff --git a/test_plans/speed_capabilities_test_plan.rst b/test_plans/speed_capabilities_test_plan.rst
new file mode 100644
index 0000000..2821612
--- /dev/null
+++ b/test_plans/speed_capabilities_test_plan.rst
@@ -0,0 +1,84 @@
+.. # BSD LICENSE
+ #
+ # Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
+ # Copyright © 2018[, 2019] The University of New Hampshire. All rights reserved.
+ # All rights reserved.
+ #
+ # Redistribution and use in source and binary forms, with or without
+ # modification, are permitted provided that the following conditions
+ # are met:
+ #
+ # * Redistributions of source code must retain the above copyright
+ # notice, this list of conditions and the following disclaimer.
+ # * Redistributions in binary form must reproduce the above copyright
+ # notice, this list of conditions and the following disclaimer in
+ # the documentation and/or other materials provided with the
+ # distribution.
+ # * Neither the name of Intel Corporation nor the names of its
+ # contributors may be used to endorse or promote products derived
+ # from this software without specific prior written permission.
+ #
+ # THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ # "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ # LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ # A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ # OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ # SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ # LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ # DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ # THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ # (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ # OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+=======================
+Speed Capabilities Test
+=======================
+
+The Speed Capabilities Test checks the speeds that the device lists and compares
+it to a user-defined set of expected speeds set in the ``speed_capabilities.cfg``.
+
+Prerequisites
+=============
+
+If using vfio the kernel must be >= 3.6+ and VT-d must be enabled in bios.When
+using vfio, use the following commands to load the vfio driver and bind it
+to the device under test::
+
+ modprobe vfio
+ modprobe vfio-pci
+ usertools/dpdk-devbind.py --bind=vfio-pci device_bus_id
+
+Assuming that ports ``0`` and ``1`` of the test target are directly connected
+to the traffic generator, launch the ``testpmd`` application with the following
+arguments::
+
+ ./build/app/testpmd -- -i --portmask=0x3
+
+Start packet forwarding in the ``testpmd`` application with the ``start``
+command. Then, for each port on the target make the Traffic Generator
+transmit a packet to the port of arbitrary size less than the MTU of
+the target port, checking that the same amount of frames and bytes
+are received back by the Traffic Generator from the port.
+
+Ensure that the ``speed_capabilities.cfg`` file correctly reflects the speeds
+the device is expected to run at.
+
+
+Test Case : Speed Capabilities Test
+===================================
+
+1. Use testpmd to retrieve the speed information that the interface is linked at::
+
+ testpmd> show port info <PORT_ID>
+
+2. Compares the speed value against the rate in the speed_capabilities.cfg file.
+ The supported options for expected speeds are 1G, 10G, 25G, 40G, and 100G. Each interface must have an expected speed associated with it.
+ Example file below::
+
+ [suite]
+ expected_speeds={'interface1': '10G', 'interface2': '100M'}
+
+
+3. Verifies that the speeds matches accordingly.
+
+4. Repeats the verification for each NIC and interface found on the system.
diff --git a/tests/TestSuite_speed_capabilities.py b/tests/TestSuite_speed_capabilities.py
new file mode 100644
index 0000000..25c45e4
--- /dev/null
+++ b/tests/TestSuite_speed_capabilities.py
@@ -0,0 +1,120 @@
+# BSD LICENSE
+#
+# Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
+# Copyright © 2018[, 2019] The University of New Hampshire. All rights reserved.
+# All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# * Redistributions of source code must retain the above copyright
+# notice, this list of conditions and the following disclaimer.
+# * Redistributions in binary form must reproduce the above copyright
+# notice, this list of conditions and the following disclaimer in
+# the documentation and/or other materials provided with the
+# distribution.
+# * Neither the name of Intel Corporation nor the names of its
+# contributors may be used to endorse or promote products derived
+# from this software without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+# A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+# OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+# LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+# DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+# THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+# (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+# OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+"""
+DPDK Test suite.
+"""
+import utils
+from pmd_output import PmdOutput
+from test_case import TestCase
+
+
+class TestSpeedCapabilities(TestCase):
+ def set_up_all(self):
+ """
+ Run at the start of each test suite.
+ """
+ self.ports = self.dut.get_ports()
+ self.ports_socket = self.dut.get_numa_id(self.ports[0])
+
+ for port in self.ports:
+ self.tester.send_expect(f"ifconfig {self.tester.get_interface(self.tester.get_local_port(port))} mtu 5000"
+ , "# ")
+
+ self.pmdout = PmdOutput(self.dut)
+ self.vm_env_done = False
+
+ def test_speed_capabilities(self):
+ self.pmdout.start_testpmd("Default")
+
+ cfg_content = self.get_suite_cfg()
+ expected_speeds = cfg_content.get('expected_speeds')
+
+ detected_interfaces = []
+
+ for port in self.ports:
+ interface_name = self.tester.get_interface(self.tester.get_local_port(port))
+
+ # Gives the speed in Mb/s
+ interface_speed = self.pmdout.get_port_link_speed(port)
+
+ self.verify(interface_name in expected_speeds, f"The interface {interface_name} does not have an expected "
+ f"speed associated with it.")
+
+ detected_interfaces.append(interface_name)
+
+ expected_speed = expected_speeds[interface_name]
+
+ # Isolates the unit (Either M or G)
+ expected_speed_unit = ''.join(i for i in expected_speed if not i.isdigit())
+
+ # Removes the unit from the speed
+ expected_speed = ''.join(i for i in expected_speed if i.isdigit())
+
+ self.verify(len(interface_speed) > 0,
+ f"A valid speed could not be read for the interface {interface_name}.")
+
+ # Converts Gb/s to Mb/s for consistent comparison
+ if expected_speed_unit == "G":
+ expected_speed += "000"
+
+ self.verify(interface_speed == expected_speed,
+ f"Detected speed: {interface_speed} Mb/s for the interface {interface_name}, "
+ f"but expected speed: {expected_speed} Mb/s")
+
+ for key, value in expected_speeds.items():
+ self.verify(key in detected_interfaces, f"The interface {key} expected the speed {value} in "
+ "speed_capabilities.cfg file, but it did not detect that interface.")
+
+ def tear_down(self):
+ """
+ Run after each test case.
+ """
+ self.dut.kill_all()
+ self.pmdout.start_testpmd("Default", "--portmask=%s --port-topology=loop" % utils.create_mask(self.ports),
+ socket=self.ports_socket)
+ ports_num = len(self.ports)
+ # link up test, to avoid failing further tests if link was down
+ for i in range(ports_num):
+ # sometimes output text messing up testpmd prompt so trimmed prompt
+ self.dut.send_expect("set link-up port %d" % i, ">")
+ # start ports, to avoid failing further tests if ports are stopped
+ self.dut.send_expect("port start all", "testpmd> ", 100)
+ self.dut.send_expect("quit", "# ")
+
+ def tear_down_all(self):
+ """
+ Run after each test suite.
+ """
+ if self.vm_env_done:
+ self.destroy_vm_env()
+ self.dut.kill_all()
--
2.17.1
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [dts] [PATCH] speed-capabilities: added Speed Capabilities test case
2020-07-07 13:40 [dts] [PATCH] speed-capabilities: added " dkirichok
@ 2020-07-20 7:12 ` Tu, Lijuan
0 siblings, 0 replies; 5+ messages in thread
From: Tu, Lijuan @ 2020-07-20 7:12 UTC (permalink / raw)
To: dkirichok, dts
Cc: mb, lylavoie, thomas, dev, david.marchand, Yigit, Ferruh,
arybchenko, i.dyukov, rasland, j.hendergart, dliu, ohilyard
Applied, thanks
> -----Original Message-----
> From: dts <dts-bounces@dpdk.org> On Behalf Of dkirichok@iol.unh.edu
> Sent: 2020年7月7日 21:41
> To: dts@dpdk.org
> Cc: mb@smartsharesystems.com; lylavoie@iol.unh.edu; thomas@monjalon.net;
> dev@dpdk.org; david.marchand@redhat.com; Yigit, Ferruh
> <ferruh.yigit@intel.com>; arybchenko@solarflare.com; i.dyukov@samsung.com;
> rasland@mellanox.com; j.hendergart@f5.com; dliu@iol.unh.edu;
> ohilyard@iol.unh.edu; Daniel Kirichok <dkirichok@iol.unh.edu>
> Subject: [dts] [PATCH] speed-capabilities: added Speed Capabilities test case
>
> From: Daniel Kirichok <dkirichok@iol.unh.edu>
>
> Added test case for checking speed capabilities.
>
> Signed-off-by: Daniel Kirichok <dkirichok@iol.unh.edu>
> ---
> conf/speed_capabilities.cfg | 4 +
> test_plans/speed_capabilities_test_plan.rst | 84 ++++++++++++++
> tests/TestSuite_speed_capabilities.py | 120 ++++++++++++++++++++
> 3 files changed, 208 insertions(+)
> create mode 100644 conf/speed_capabilities.cfg create mode 100644
> test_plans/speed_capabilities_test_plan.rst
> create mode 100644 tests/TestSuite_speed_capabilities.py
>
> diff --git a/conf/speed_capabilities.cfg b/conf/speed_capabilities.cfg new file
> mode 100644 index 0000000..c22f531
> --- /dev/null
> +++ b/conf/speed_capabilities.cfg
> @@ -0,0 +1,4 @@
> +[suite]
> +# The format for entering expected speeds is {'<INTERFACE>':'<EXPECTED
> +SPEED>',...} # Unit for speed must be in G or M
> +expected_speeds={'interface1': '10G', 'interface2': '100M'}
> diff --git a/test_plans/speed_capabilities_test_plan.rst
> b/test_plans/speed_capabilities_test_plan.rst
> new file mode 100644
> index 0000000..2821612
> --- /dev/null
> +++ b/test_plans/speed_capabilities_test_plan.rst
> @@ -0,0 +1,84 @@
> +.. # BSD LICENSE
> + #
> + # Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
> + # Copyright © 2018[, 2019] The University of New Hampshire. All rights
> reserved.
> + # All rights reserved.
> + #
> + # Redistribution and use in source and binary forms, with or without
> + # modification, are permitted provided that the following conditions
> + # are met:
> + #
> + # * Redistributions of source code must retain the above copyright
> + # notice, this list of conditions and the following disclaimer.
> + # * Redistributions in binary form must reproduce the above copyright
> + # notice, this list of conditions and the following disclaimer in
> + # the documentation and/or other materials provided with the
> + # distribution.
> + # * Neither the name of Intel Corporation nor the names of its
> + # contributors may be used to endorse or promote products derived
> + # from this software without specific prior written permission.
> + #
> + # THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
> CONTRIBUTORS
> + # "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT
> NOT
> + # LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
> FITNESS FOR
> + # A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
> COPYRIGHT
> + # OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
> INCIDENTAL,
> + # SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
> NOT
> + # LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
> OF USE,
> + # DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
> ON ANY
> + # THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
> TORT
> + # (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF
> THE USE
> + # OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
> DAMAGE.
> +
> +=======================
> +Speed Capabilities Test
> +=======================
> +
> +The Speed Capabilities Test checks the speeds that the device lists and
> +compares it to a user-defined set of expected speeds set in the
> ``speed_capabilities.cfg``.
> +
> +Prerequisites
> +=============
> +
> +If using vfio the kernel must be >= 3.6+ and VT-d must be enabled in
> +bios.When using vfio, use the following commands to load the vfio
> +driver and bind it to the device under test::
> +
> + modprobe vfio
> + modprobe vfio-pci
> + usertools/dpdk-devbind.py --bind=vfio-pci device_bus_id
> +
> +Assuming that ports ``0`` and ``1`` of the test target are directly
> +connected to the traffic generator, launch the ``testpmd`` application
> +with the following
> +arguments::
> +
> + ./build/app/testpmd -- -i --portmask=0x3
> +
> +Start packet forwarding in the ``testpmd`` application with the
> +``start`` command. Then, for each port on the target make the Traffic
> +Generator transmit a packet to the port of arbitrary size less than the
> +MTU of the target port, checking that the same amount of frames and
> +bytes are received back by the Traffic Generator from the port.
> +
> +Ensure that the ``speed_capabilities.cfg`` file correctly reflects the
> +speeds the device is expected to run at.
> +
> +
> +Test Case : Speed Capabilities Test
> +===================================
> +
> +1. Use testpmd to retrieve the speed information that the interface is linked at::
> +
> + testpmd> show port info <PORT_ID>
> +
> +2. Compares the speed value against the rate in the speed_capabilities.cfg file.
> + The supported options for expected speeds are 1G, 10G, 25G, 40G, and 100G.
> Each interface must have an expected speed associated with it.
> + Example file below::
> +
> + [suite]
> + expected_speeds={'interface1': '10G', 'interface2': '100M'}
> +
> +
> +3. Verifies that the speeds matches accordingly.
> +
> +4. Repeats the verification for each NIC and interface found on the system.
> diff --git a/tests/TestSuite_speed_capabilities.py
> b/tests/TestSuite_speed_capabilities.py
> new file mode 100644
> index 0000000..25c45e4
> --- /dev/null
> +++ b/tests/TestSuite_speed_capabilities.py
> @@ -0,0 +1,120 @@
> +# BSD LICENSE
> +#
> +# Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
> +# Copyright © 2018[, 2019] The University of New Hampshire. All rights
> reserved.
> +# All rights reserved.
> +#
> +# Redistribution and use in source and binary forms, with or without #
> +modification, are permitted provided that the following conditions #
> +are met:
> +#
> +# * Redistributions of source code must retain the above copyright
> +# notice, this list of conditions and the following disclaimer.
> +# * Redistributions in binary form must reproduce the above copyright
> +# notice, this list of conditions and the following disclaimer in
> +# the documentation and/or other materials provided with the
> +# distribution.
> +# * Neither the name of Intel Corporation nor the names of its
> +# contributors may be used to endorse or promote products derived
> +# from this software without specific prior written permission.
> +#
> +# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
> CONTRIBUTORS #
> +"AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT #
> +LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
> FOR #
> +A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
> COPYRIGHT #
> +OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
> INCIDENTAL, #
> +SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
> #
> +LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
> USE, #
> +DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
> ANY #
> +THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT #
> +(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
> USE #
> +OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> +
> +"""
> +DPDK Test suite.
> +"""
> +import utils
> +from pmd_output import PmdOutput
> +from test_case import TestCase
> +
> +
> +class TestSpeedCapabilities(TestCase):
> + def set_up_all(self):
> + """
> + Run at the start of each test suite.
> + """
> + self.ports = self.dut.get_ports()
> + self.ports_socket = self.dut.get_numa_id(self.ports[0])
> +
> + for port in self.ports:
> + self.tester.send_expect(f"ifconfig
> {self.tester.get_interface(self.tester.get_local_port(port))} mtu 5000"
> + , "# ")
> +
> + self.pmdout = PmdOutput(self.dut)
> + self.vm_env_done = False
> +
> + def test_speed_capabilities(self):
> + self.pmdout.start_testpmd("Default")
> +
> + cfg_content = self.get_suite_cfg()
> + expected_speeds = cfg_content.get('expected_speeds')
> +
> + detected_interfaces = []
> +
> + for port in self.ports:
> + interface_name =
> + self.tester.get_interface(self.tester.get_local_port(port))
> +
> + # Gives the speed in Mb/s
> + interface_speed = self.pmdout.get_port_link_speed(port)
> +
> + self.verify(interface_name in expected_speeds, f"The interface
> {interface_name} does not have an expected "
> + f"speed
> + associated with it.")
> +
> + detected_interfaces.append(interface_name)
> +
> + expected_speed = expected_speeds[interface_name]
> +
> + # Isolates the unit (Either M or G)
> + expected_speed_unit = ''.join(i for i in expected_speed if
> + not i.isdigit())
> +
> + # Removes the unit from the speed
> + expected_speed = ''.join(i for i in expected_speed if
> + i.isdigit())
> +
> + self.verify(len(interface_speed) > 0,
> + f"A valid speed could not be read for the
> + interface {interface_name}.")
> +
> + # Converts Gb/s to Mb/s for consistent comparison
> + if expected_speed_unit == "G":
> + expected_speed += "000"
> +
> + self.verify(interface_speed == expected_speed,
> + f"Detected speed: {interface_speed} Mb/s for the interface
> {interface_name}, "
> + f"but expected speed: {expected_speed} Mb/s")
> +
> + for key, value in expected_speeds.items():
> + self.verify(key in detected_interfaces, f"The interface {key} expected the
> speed {value} in "
> +
> + "speed_capabilities.cfg file, but it did not detect that interface.")
> +
> + def tear_down(self):
> + """
> + Run after each test case.
> + """
> + self.dut.kill_all()
> + self.pmdout.start_testpmd("Default", "--portmask=%s --port-
> topology=loop" % utils.create_mask(self.ports),
> + socket=self.ports_socket)
> + ports_num = len(self.ports)
> + # link up test, to avoid failing further tests if link was down
> + for i in range(ports_num):
> + # sometimes output text messing up testpmd prompt so trimmed prompt
> + self.dut.send_expect("set link-up port %d" % i, ">")
> + # start ports, to avoid failing further tests if ports are stopped
> + self.dut.send_expect("port start all", "testpmd> ", 100)
> + self.dut.send_expect("quit", "# ")
> +
> + def tear_down_all(self):
> + """
> + Run after each test suite.
> + """
> + if self.vm_env_done:
> + self.destroy_vm_env()
> + self.dut.kill_all()
> --
> 2.17.1
^ permalink raw reply [flat|nested] 5+ messages in thread
* [dts] [PATCH] speed-capabilities: added Speed Capabilities test case
@ 2020-07-07 13:40 dkirichok
2020-07-20 7:12 ` Tu, Lijuan
0 siblings, 1 reply; 5+ messages in thread
From: dkirichok @ 2020-07-07 13:40 UTC (permalink / raw)
To: dts
Cc: mb, lylavoie, thomas, dev, david.marchand, ferruh.yigit,
arybchenko, i.dyukov, rasland, j.hendergart, dliu, ohilyard,
Daniel Kirichok
From: Daniel Kirichok <dkirichok@iol.unh.edu>
Added test case for checking speed capabilities.
Signed-off-by: Daniel Kirichok <dkirichok@iol.unh.edu>
---
conf/speed_capabilities.cfg | 4 +
test_plans/speed_capabilities_test_plan.rst | 84 ++++++++++++++
tests/TestSuite_speed_capabilities.py | 120 ++++++++++++++++++++
3 files changed, 208 insertions(+)
create mode 100644 conf/speed_capabilities.cfg
create mode 100644 test_plans/speed_capabilities_test_plan.rst
create mode 100644 tests/TestSuite_speed_capabilities.py
diff --git a/conf/speed_capabilities.cfg b/conf/speed_capabilities.cfg
new file mode 100644
index 0000000..c22f531
--- /dev/null
+++ b/conf/speed_capabilities.cfg
@@ -0,0 +1,4 @@
+[suite]
+# The format for entering expected speeds is {'<INTERFACE>':'<EXPECTED SPEED>',...}
+# Unit for speed must be in G or M
+expected_speeds={'interface1': '10G', 'interface2': '100M'}
diff --git a/test_plans/speed_capabilities_test_plan.rst b/test_plans/speed_capabilities_test_plan.rst
new file mode 100644
index 0000000..2821612
--- /dev/null
+++ b/test_plans/speed_capabilities_test_plan.rst
@@ -0,0 +1,84 @@
+.. # BSD LICENSE
+ #
+ # Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
+ # Copyright © 2018[, 2019] The University of New Hampshire. All rights reserved.
+ # All rights reserved.
+ #
+ # Redistribution and use in source and binary forms, with or without
+ # modification, are permitted provided that the following conditions
+ # are met:
+ #
+ # * Redistributions of source code must retain the above copyright
+ # notice, this list of conditions and the following disclaimer.
+ # * Redistributions in binary form must reproduce the above copyright
+ # notice, this list of conditions and the following disclaimer in
+ # the documentation and/or other materials provided with the
+ # distribution.
+ # * Neither the name of Intel Corporation nor the names of its
+ # contributors may be used to endorse or promote products derived
+ # from this software without specific prior written permission.
+ #
+ # THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ # "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ # LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ # A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ # OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ # SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ # LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ # DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ # THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ # (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ # OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+=======================
+Speed Capabilities Test
+=======================
+
+The Speed Capabilities Test checks the speeds that the device lists and compares
+it to a user-defined set of expected speeds set in the ``speed_capabilities.cfg``.
+
+Prerequisites
+=============
+
+If using vfio the kernel must be >= 3.6+ and VT-d must be enabled in bios.When
+using vfio, use the following commands to load the vfio driver and bind it
+to the device under test::
+
+ modprobe vfio
+ modprobe vfio-pci
+ usertools/dpdk-devbind.py --bind=vfio-pci device_bus_id
+
+Assuming that ports ``0`` and ``1`` of the test target are directly connected
+to the traffic generator, launch the ``testpmd`` application with the following
+arguments::
+
+ ./build/app/testpmd -- -i --portmask=0x3
+
+Start packet forwarding in the ``testpmd`` application with the ``start``
+command. Then, for each port on the target make the Traffic Generator
+transmit a packet to the port of arbitrary size less than the MTU of
+the target port, checking that the same amount of frames and bytes
+are received back by the Traffic Generator from the port.
+
+Ensure that the ``speed_capabilities.cfg`` file correctly reflects the speeds
+the device is expected to run at.
+
+
+Test Case : Speed Capabilities Test
+===================================
+
+1. Use testpmd to retrieve the speed information that the interface is linked at::
+
+ testpmd> show port info <PORT_ID>
+
+2. Compares the speed value against the rate in the speed_capabilities.cfg file.
+ The supported options for expected speeds are 1G, 10G, 25G, 40G, and 100G. Each interface must have an expected speed associated with it.
+ Example file below::
+
+ [suite]
+ expected_speeds={'interface1': '10G', 'interface2': '100M'}
+
+
+3. Verifies that the speeds matches accordingly.
+
+4. Repeats the verification for each NIC and interface found on the system.
diff --git a/tests/TestSuite_speed_capabilities.py b/tests/TestSuite_speed_capabilities.py
new file mode 100644
index 0000000..25c45e4
--- /dev/null
+++ b/tests/TestSuite_speed_capabilities.py
@@ -0,0 +1,120 @@
+# BSD LICENSE
+#
+# Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
+# Copyright © 2018[, 2019] The University of New Hampshire. All rights reserved.
+# All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# * Redistributions of source code must retain the above copyright
+# notice, this list of conditions and the following disclaimer.
+# * Redistributions in binary form must reproduce the above copyright
+# notice, this list of conditions and the following disclaimer in
+# the documentation and/or other materials provided with the
+# distribution.
+# * Neither the name of Intel Corporation nor the names of its
+# contributors may be used to endorse or promote products derived
+# from this software without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+# A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+# OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+# LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+# DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+# THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+# (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+# OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+"""
+DPDK Test suite.
+"""
+import utils
+from pmd_output import PmdOutput
+from test_case import TestCase
+
+
+class TestSpeedCapabilities(TestCase):
+ def set_up_all(self):
+ """
+ Run at the start of each test suite.
+ """
+ self.ports = self.dut.get_ports()
+ self.ports_socket = self.dut.get_numa_id(self.ports[0])
+
+ for port in self.ports:
+ self.tester.send_expect(f"ifconfig {self.tester.get_interface(self.tester.get_local_port(port))} mtu 5000"
+ , "# ")
+
+ self.pmdout = PmdOutput(self.dut)
+ self.vm_env_done = False
+
+ def test_speed_capabilities(self):
+ self.pmdout.start_testpmd("Default")
+
+ cfg_content = self.get_suite_cfg()
+ expected_speeds = cfg_content.get('expected_speeds')
+
+ detected_interfaces = []
+
+ for port in self.ports:
+ interface_name = self.tester.get_interface(self.tester.get_local_port(port))
+
+ # Gives the speed in Mb/s
+ interface_speed = self.pmdout.get_port_link_speed(port)
+
+ self.verify(interface_name in expected_speeds, f"The interface {interface_name} does not have an expected "
+ f"speed associated with it.")
+
+ detected_interfaces.append(interface_name)
+
+ expected_speed = expected_speeds[interface_name]
+
+ # Isolates the unit (Either M or G)
+ expected_speed_unit = ''.join(i for i in expected_speed if not i.isdigit())
+
+ # Removes the unit from the speed
+ expected_speed = ''.join(i for i in expected_speed if i.isdigit())
+
+ self.verify(len(interface_speed) > 0,
+ f"A valid speed could not be read for the interface {interface_name}.")
+
+ # Converts Gb/s to Mb/s for consistent comparison
+ if expected_speed_unit == "G":
+ expected_speed += "000"
+
+ self.verify(interface_speed == expected_speed,
+ f"Detected speed: {interface_speed} Mb/s for the interface {interface_name}, "
+ f"but expected speed: {expected_speed} Mb/s")
+
+ for key, value in expected_speeds.items():
+ self.verify(key in detected_interfaces, f"The interface {key} expected the speed {value} in "
+ "speed_capabilities.cfg file, but it did not detect that interface.")
+
+ def tear_down(self):
+ """
+ Run after each test case.
+ """
+ self.dut.kill_all()
+ self.pmdout.start_testpmd("Default", "--portmask=%s --port-topology=loop" % utils.create_mask(self.ports),
+ socket=self.ports_socket)
+ ports_num = len(self.ports)
+ # link up test, to avoid failing further tests if link was down
+ for i in range(ports_num):
+ # sometimes output text messing up testpmd prompt so trimmed prompt
+ self.dut.send_expect("set link-up port %d" % i, ">")
+ # start ports, to avoid failing further tests if ports are stopped
+ self.dut.send_expect("port start all", "testpmd> ", 100)
+ self.dut.send_expect("quit", "# ")
+
+ def tear_down_all(self):
+ """
+ Run after each test suite.
+ """
+ if self.vm_env_done:
+ self.destroy_vm_env()
+ self.dut.kill_all()
--
2.17.1
^ permalink raw reply [flat|nested] 5+ messages in thread
* [dts] [PATCH] speed-capabilities: Added Speed Capabilities test case
@ 2020-06-29 20:28 dkirichok
0 siblings, 0 replies; 5+ messages in thread
From: dkirichok @ 2020-06-29 20:28 UTC (permalink / raw)
To: dts
Cc: mb, lylavoie, thomas, dev, david.marchand, ferruh.yigit,
arybchenko, i.dyukov, rasland, j.hendergart, ohilyard,
Daniel Kirichok
From: Daniel Kirichok <dkirichok@iol.unh.edu>
Added test case for checking speed capabilities.
Signed-off-by: Daniel Kirichok <dkirichok@iol.unh.edu>
---
conf/speed_capabilities.cfg | 4 +
test_plans/speed_capabilities_test_plan.rst | 84 ++++++++++++++
tests/TestSuite_speed_capabilities.py | 120 ++++++++++++++++++++
3 files changed, 208 insertions(+)
create mode 100644 conf/speed_capabilities.cfg
create mode 100644 test_plans/speed_capabilities_test_plan.rst
create mode 100644 tests/TestSuite_speed_capabilities.py
diff --git a/conf/speed_capabilities.cfg b/conf/speed_capabilities.cfg
new file mode 100644
index 0000000..c22f531
--- /dev/null
+++ b/conf/speed_capabilities.cfg
@@ -0,0 +1,4 @@
+[suite]
+# The format for entering expected speeds is {'<INTERFACE>':'<EXPECTED SPEED>',...}
+# Unit for speed must be in G or M
+expected_speeds={'interface1': '10G', 'interface2': '100M'}
diff --git a/test_plans/speed_capabilities_test_plan.rst b/test_plans/speed_capabilities_test_plan.rst
new file mode 100644
index 0000000..2821612
--- /dev/null
+++ b/test_plans/speed_capabilities_test_plan.rst
@@ -0,0 +1,84 @@
+.. # BSD LICENSE
+ #
+ # Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
+ # Copyright © 2018[, 2019] The University of New Hampshire. All rights reserved.
+ # All rights reserved.
+ #
+ # Redistribution and use in source and binary forms, with or without
+ # modification, are permitted provided that the following conditions
+ # are met:
+ #
+ # * Redistributions of source code must retain the above copyright
+ # notice, this list of conditions and the following disclaimer.
+ # * Redistributions in binary form must reproduce the above copyright
+ # notice, this list of conditions and the following disclaimer in
+ # the documentation and/or other materials provided with the
+ # distribution.
+ # * Neither the name of Intel Corporation nor the names of its
+ # contributors may be used to endorse or promote products derived
+ # from this software without specific prior written permission.
+ #
+ # THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ # "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ # LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ # A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ # OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ # SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ # LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ # DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ # THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ # (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ # OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+=======================
+Speed Capabilities Test
+=======================
+
+The Speed Capabilities Test checks the speeds that the device lists and compares
+it to a user-defined set of expected speeds set in the ``speed_capabilities.cfg``.
+
+Prerequisites
+=============
+
+If using vfio the kernel must be >= 3.6+ and VT-d must be enabled in bios.When
+using vfio, use the following commands to load the vfio driver and bind it
+to the device under test::
+
+ modprobe vfio
+ modprobe vfio-pci
+ usertools/dpdk-devbind.py --bind=vfio-pci device_bus_id
+
+Assuming that ports ``0`` and ``1`` of the test target are directly connected
+to the traffic generator, launch the ``testpmd`` application with the following
+arguments::
+
+ ./build/app/testpmd -- -i --portmask=0x3
+
+Start packet forwarding in the ``testpmd`` application with the ``start``
+command. Then, for each port on the target make the Traffic Generator
+transmit a packet to the port of arbitrary size less than the MTU of
+the target port, checking that the same amount of frames and bytes
+are received back by the Traffic Generator from the port.
+
+Ensure that the ``speed_capabilities.cfg`` file correctly reflects the speeds
+the device is expected to run at.
+
+
+Test Case : Speed Capabilities Test
+===================================
+
+1. Use testpmd to retrieve the speed information that the interface is linked at::
+
+ testpmd> show port info <PORT_ID>
+
+2. Compares the speed value against the rate in the speed_capabilities.cfg file.
+ The supported options for expected speeds are 1G, 10G, 25G, 40G, and 100G. Each interface must have an expected speed associated with it.
+ Example file below::
+
+ [suite]
+ expected_speeds={'interface1': '10G', 'interface2': '100M'}
+
+
+3. Verifies that the speeds matches accordingly.
+
+4. Repeats the verification for each NIC and interface found on the system.
diff --git a/tests/TestSuite_speed_capabilities.py b/tests/TestSuite_speed_capabilities.py
new file mode 100644
index 0000000..25c45e4
--- /dev/null
+++ b/tests/TestSuite_speed_capabilities.py
@@ -0,0 +1,120 @@
+# BSD LICENSE
+#
+# Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
+# Copyright © 2018[, 2019] The University of New Hampshire. All rights reserved.
+# All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# * Redistributions of source code must retain the above copyright
+# notice, this list of conditions and the following disclaimer.
+# * Redistributions in binary form must reproduce the above copyright
+# notice, this list of conditions and the following disclaimer in
+# the documentation and/or other materials provided with the
+# distribution.
+# * Neither the name of Intel Corporation nor the names of its
+# contributors may be used to endorse or promote products derived
+# from this software without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+# A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+# OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+# LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+# DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+# THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+# (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+# OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+"""
+DPDK Test suite.
+"""
+import utils
+from pmd_output import PmdOutput
+from test_case import TestCase
+
+
+class TestSpeedCapabilities(TestCase):
+ def set_up_all(self):
+ """
+ Run at the start of each test suite.
+ """
+ self.ports = self.dut.get_ports()
+ self.ports_socket = self.dut.get_numa_id(self.ports[0])
+
+ for port in self.ports:
+ self.tester.send_expect(f"ifconfig {self.tester.get_interface(self.tester.get_local_port(port))} mtu 5000"
+ , "# ")
+
+ self.pmdout = PmdOutput(self.dut)
+ self.vm_env_done = False
+
+ def test_speed_capabilities(self):
+ self.pmdout.start_testpmd("Default")
+
+ cfg_content = self.get_suite_cfg()
+ expected_speeds = cfg_content.get('expected_speeds')
+
+ detected_interfaces = []
+
+ for port in self.ports:
+ interface_name = self.tester.get_interface(self.tester.get_local_port(port))
+
+ # Gives the speed in Mb/s
+ interface_speed = self.pmdout.get_port_link_speed(port)
+
+ self.verify(interface_name in expected_speeds, f"The interface {interface_name} does not have an expected "
+ f"speed associated with it.")
+
+ detected_interfaces.append(interface_name)
+
+ expected_speed = expected_speeds[interface_name]
+
+ # Isolates the unit (Either M or G)
+ expected_speed_unit = ''.join(i for i in expected_speed if not i.isdigit())
+
+ # Removes the unit from the speed
+ expected_speed = ''.join(i for i in expected_speed if i.isdigit())
+
+ self.verify(len(interface_speed) > 0,
+ f"A valid speed could not be read for the interface {interface_name}.")
+
+ # Converts Gb/s to Mb/s for consistent comparison
+ if expected_speed_unit == "G":
+ expected_speed += "000"
+
+ self.verify(interface_speed == expected_speed,
+ f"Detected speed: {interface_speed} Mb/s for the interface {interface_name}, "
+ f"but expected speed: {expected_speed} Mb/s")
+
+ for key, value in expected_speeds.items():
+ self.verify(key in detected_interfaces, f"The interface {key} expected the speed {value} in "
+ "speed_capabilities.cfg file, but it did not detect that interface.")
+
+ def tear_down(self):
+ """
+ Run after each test case.
+ """
+ self.dut.kill_all()
+ self.pmdout.start_testpmd("Default", "--portmask=%s --port-topology=loop" % utils.create_mask(self.ports),
+ socket=self.ports_socket)
+ ports_num = len(self.ports)
+ # link up test, to avoid failing further tests if link was down
+ for i in range(ports_num):
+ # sometimes output text messing up testpmd prompt so trimmed prompt
+ self.dut.send_expect("set link-up port %d" % i, ">")
+ # start ports, to avoid failing further tests if ports are stopped
+ self.dut.send_expect("port start all", "testpmd> ", 100)
+ self.dut.send_expect("quit", "# ")
+
+ def tear_down_all(self):
+ """
+ Run after each test suite.
+ """
+ if self.vm_env_done:
+ self.destroy_vm_env()
+ self.dut.kill_all()
--
2.17.1
^ permalink raw reply [flat|nested] 5+ messages in thread
* [dts] [PATCH] speed-capabilities: Added Speed Capabilities test case
@ 2020-06-29 20:03 dkirichok
0 siblings, 0 replies; 5+ messages in thread
From: dkirichok @ 2020-06-29 20:03 UTC (permalink / raw)
To: dts
Cc: mb, lylavoie, thomas, dev, david.marchand, ferruh.yigit,
arybchenko, i.dyukov, rasland, j.hendergart, ohilyard,
Daniel Kirichok
From: Daniel Kirichok <dkirichok@iol.unh.edu>
Added Speed Capabilities test which compares detected interface speeds with what is expected in the config file.
---
conf/speed_capabilities.cfg | 4 +
test_plans/speed_capabilities_test_plan.rst | 84 ++++++++++++++
tests/TestSuite_speed_capabilities.py | 120 ++++++++++++++++++++
3 files changed, 208 insertions(+)
create mode 100644 conf/speed_capabilities.cfg
create mode 100644 test_plans/speed_capabilities_test_plan.rst
create mode 100644 tests/TestSuite_speed_capabilities.py
diff --git a/conf/speed_capabilities.cfg b/conf/speed_capabilities.cfg
new file mode 100644
index 0000000..c22f531
--- /dev/null
+++ b/conf/speed_capabilities.cfg
@@ -0,0 +1,4 @@
+[suite]
+# The format for entering expected speeds is {'<INTERFACE>':'<EXPECTED SPEED>',...}
+# Unit for speed must be in G or M
+expected_speeds={'interface1': '10G', 'interface2': '100M'}
diff --git a/test_plans/speed_capabilities_test_plan.rst b/test_plans/speed_capabilities_test_plan.rst
new file mode 100644
index 0000000..2821612
--- /dev/null
+++ b/test_plans/speed_capabilities_test_plan.rst
@@ -0,0 +1,84 @@
+.. # BSD LICENSE
+ #
+ # Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
+ # Copyright © 2018[, 2019] The University of New Hampshire. All rights reserved.
+ # All rights reserved.
+ #
+ # Redistribution and use in source and binary forms, with or without
+ # modification, are permitted provided that the following conditions
+ # are met:
+ #
+ # * Redistributions of source code must retain the above copyright
+ # notice, this list of conditions and the following disclaimer.
+ # * Redistributions in binary form must reproduce the above copyright
+ # notice, this list of conditions and the following disclaimer in
+ # the documentation and/or other materials provided with the
+ # distribution.
+ # * Neither the name of Intel Corporation nor the names of its
+ # contributors may be used to endorse or promote products derived
+ # from this software without specific prior written permission.
+ #
+ # THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ # "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ # LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ # A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ # OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ # SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ # LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ # DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ # THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ # (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ # OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+=======================
+Speed Capabilities Test
+=======================
+
+The Speed Capabilities Test checks the speeds that the device lists and compares
+it to a user-defined set of expected speeds set in the ``speed_capabilities.cfg``.
+
+Prerequisites
+=============
+
+If using vfio the kernel must be >= 3.6+ and VT-d must be enabled in bios.When
+using vfio, use the following commands to load the vfio driver and bind it
+to the device under test::
+
+ modprobe vfio
+ modprobe vfio-pci
+ usertools/dpdk-devbind.py --bind=vfio-pci device_bus_id
+
+Assuming that ports ``0`` and ``1`` of the test target are directly connected
+to the traffic generator, launch the ``testpmd`` application with the following
+arguments::
+
+ ./build/app/testpmd -- -i --portmask=0x3
+
+Start packet forwarding in the ``testpmd`` application with the ``start``
+command. Then, for each port on the target make the Traffic Generator
+transmit a packet to the port of arbitrary size less than the MTU of
+the target port, checking that the same amount of frames and bytes
+are received back by the Traffic Generator from the port.
+
+Ensure that the ``speed_capabilities.cfg`` file correctly reflects the speeds
+the device is expected to run at.
+
+
+Test Case : Speed Capabilities Test
+===================================
+
+1. Use testpmd to retrieve the speed information that the interface is linked at::
+
+ testpmd> show port info <PORT_ID>
+
+2. Compares the speed value against the rate in the speed_capabilities.cfg file.
+ The supported options for expected speeds are 1G, 10G, 25G, 40G, and 100G. Each interface must have an expected speed associated with it.
+ Example file below::
+
+ [suite]
+ expected_speeds={'interface1': '10G', 'interface2': '100M'}
+
+
+3. Verifies that the speeds matches accordingly.
+
+4. Repeats the verification for each NIC and interface found on the system.
diff --git a/tests/TestSuite_speed_capabilities.py b/tests/TestSuite_speed_capabilities.py
new file mode 100644
index 0000000..25c45e4
--- /dev/null
+++ b/tests/TestSuite_speed_capabilities.py
@@ -0,0 +1,120 @@
+# BSD LICENSE
+#
+# Copyright(c) 2010-2014 Intel Corporation. All rights reserved.
+# Copyright © 2018[, 2019] The University of New Hampshire. All rights reserved.
+# All rights reserved.
+#
+# Redistribution and use in source and binary forms, with or without
+# modification, are permitted provided that the following conditions
+# are met:
+#
+# * Redistributions of source code must retain the above copyright
+# notice, this list of conditions and the following disclaimer.
+# * Redistributions in binary form must reproduce the above copyright
+# notice, this list of conditions and the following disclaimer in
+# the documentation and/or other materials provided with the
+# distribution.
+# * Neither the name of Intel Corporation nor the names of its
+# contributors may be used to endorse or promote products derived
+# from this software without specific prior written permission.
+#
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+# A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+# OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+# LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+# DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+# THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+# (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+# OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+"""
+DPDK Test suite.
+"""
+import utils
+from pmd_output import PmdOutput
+from test_case import TestCase
+
+
+class TestSpeedCapabilities(TestCase):
+ def set_up_all(self):
+ """
+ Run at the start of each test suite.
+ """
+ self.ports = self.dut.get_ports()
+ self.ports_socket = self.dut.get_numa_id(self.ports[0])
+
+ for port in self.ports:
+ self.tester.send_expect(f"ifconfig {self.tester.get_interface(self.tester.get_local_port(port))} mtu 5000"
+ , "# ")
+
+ self.pmdout = PmdOutput(self.dut)
+ self.vm_env_done = False
+
+ def test_speed_capabilities(self):
+ self.pmdout.start_testpmd("Default")
+
+ cfg_content = self.get_suite_cfg()
+ expected_speeds = cfg_content.get('expected_speeds')
+
+ detected_interfaces = []
+
+ for port in self.ports:
+ interface_name = self.tester.get_interface(self.tester.get_local_port(port))
+
+ # Gives the speed in Mb/s
+ interface_speed = self.pmdout.get_port_link_speed(port)
+
+ self.verify(interface_name in expected_speeds, f"The interface {interface_name} does not have an expected "
+ f"speed associated with it.")
+
+ detected_interfaces.append(interface_name)
+
+ expected_speed = expected_speeds[interface_name]
+
+ # Isolates the unit (Either M or G)
+ expected_speed_unit = ''.join(i for i in expected_speed if not i.isdigit())
+
+ # Removes the unit from the speed
+ expected_speed = ''.join(i for i in expected_speed if i.isdigit())
+
+ self.verify(len(interface_speed) > 0,
+ f"A valid speed could not be read for the interface {interface_name}.")
+
+ # Converts Gb/s to Mb/s for consistent comparison
+ if expected_speed_unit == "G":
+ expected_speed += "000"
+
+ self.verify(interface_speed == expected_speed,
+ f"Detected speed: {interface_speed} Mb/s for the interface {interface_name}, "
+ f"but expected speed: {expected_speed} Mb/s")
+
+ for key, value in expected_speeds.items():
+ self.verify(key in detected_interfaces, f"The interface {key} expected the speed {value} in "
+ "speed_capabilities.cfg file, but it did not detect that interface.")
+
+ def tear_down(self):
+ """
+ Run after each test case.
+ """
+ self.dut.kill_all()
+ self.pmdout.start_testpmd("Default", "--portmask=%s --port-topology=loop" % utils.create_mask(self.ports),
+ socket=self.ports_socket)
+ ports_num = len(self.ports)
+ # link up test, to avoid failing further tests if link was down
+ for i in range(ports_num):
+ # sometimes output text messing up testpmd prompt so trimmed prompt
+ self.dut.send_expect("set link-up port %d" % i, ">")
+ # start ports, to avoid failing further tests if ports are stopped
+ self.dut.send_expect("port start all", "testpmd> ", 100)
+ self.dut.send_expect("quit", "# ")
+
+ def tear_down_all(self):
+ """
+ Run after each test suite.
+ """
+ if self.vm_env_done:
+ self.destroy_vm_env()
+ self.dut.kill_all()
--
2.17.1
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2020-07-20 7:12 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-06-29 20:09 [dts] [PATCH] speed-capabilities: Added Speed Capabilities test case dkirichok
-- strict thread matches above, loose matches on Subject: below --
2020-07-07 13:40 [dts] [PATCH] speed-capabilities: added " dkirichok
2020-07-20 7:12 ` Tu, Lijuan
2020-06-29 20:28 [dts] [PATCH] speed-capabilities: Added " dkirichok
2020-06-29 20:03 dkirichok
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).