From: Lingli Chen <linglix.chen@intel.com>
To: dts@dpdk.org
Cc: Lingli Chen <linglix.chen@intel.com>
Subject: [dts][PATCH V1 1/2] test_plans/loopback_virtio_user_server_mode: change cases from 2 queues to 8 queues
Date: Tue, 23 Nov 2021 15:46:47 +0000 [thread overview]
Message-ID: <20211123154648.129079-2-linglix.chen@intel.com> (raw)
In-Reply-To: <20211123154648.129079-1-linglix.chen@intel.com>
1. change cases from 2 queues to 8 queues( maxime queue number supported) .
2. forwarding packet size change from 64b to 8000b(due to testpmd usage limitation, sent 8000b packet by using 2000,2000,2000,2000) when test mergeable path, such can test mergeable feature more sufficient.
Signed-off-by: Lingli Chen <linglix.chen@intel.com>
---
...back_virtio_user_server_mode_test_plan.rst | 136 +++++++++++-------
1 file changed, 81 insertions(+), 55 deletions(-)
diff --git a/test_plans/loopback_virtio_user_server_mode_test_plan.rst b/test_plans/loopback_virtio_user_server_mode_test_plan.rst
index 18d580f4..f3e9f1de 100644
--- a/test_plans/loopback_virtio_user_server_mode_test_plan.rst
+++ b/test_plans/loopback_virtio_user_server_mode_test_plan.rst
@@ -84,35 +84,38 @@ Test Case 2: Basic test for split ring server mode
Test Case 3: loopback reconnect test with split ring mergeable path and server mode
===================================================================================
-1. launch vhost as client mode with 2 queues::
+1. launch vhost as client mode with 8 queues::
rm -rf vhost-net*
./testpmd -c 0xe -n 4 --no-pci --file-prefix=vhost \
- --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=8' -- -i --nb-cores=2 --rxq=8 --txq=8
>set fwd mac
>start
-2. Launch virtio-user as server mode with 2 queues::
+2. Launch virtio-user as server mode with 8 queues and check throughput can get expected::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
- --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,mrg_rxbuf=1,in_order=0 \
- -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=8,mrg_rxbuf=1,in_order=0 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=8 --txq=8
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
+ >show port stats all
3. Quit vhost side testpmd, check the virtio-user side link status::
testpmd> show port info 0
#it should show "down"
-4. Relaunch vhost and send packets::
+4. Relaunch vhost and send chain packets::
./testpmd -c 0xe -n 4 --no-pci --file-prefix=vhost \
- --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=8' -- -i --nb-cores=2 --rxq=8 --txq=8
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
-5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+5. Check the virtio-user side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
@@ -130,22 +133,24 @@ Test Case 3: loopback reconnect test with split ring mergeable path and server m
8. Relaunch virtio-user and send packets::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
- --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,mrg_rxbuf=1,in_order=0 \
- -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=8,mrg_rxbuf=1,in_order=0 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=8 --txq=8
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
-9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+9. Check the vhost side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
testpmd>show port stats all
-10. Port restart at vhost side by below command and re-calculate the average throughput::
+10. Port restart at vhost side by below command and check throughput can get expected::
testpmd>stop
testpmd>port stop 0
testpmd>port start 0
+ testpmd>set txpkts 2000,2000,2000,2000
testpmd>start tx_first 32
testpmd>show port stats all
@@ -164,13 +169,15 @@ Test Case 4: loopback reconnect test with split ring inorder mergeable path and
>set fwd mac
>start
-2. Launch virtio-user as server mode with 2 queues::
+2. Launch virtio-user as server mode with 2 queues, check throughput can get expected::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
--vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,mrg_rxbuf=1,in_order=1 \
-- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
+ >show port stats all
3. Quit vhost side testpmd, check the virtio-user side link status::
@@ -182,9 +189,10 @@ Test Case 4: loopback reconnect test with split ring inorder mergeable path and
./testpmd -c 0xe -n 4 --no-pci --file-prefix=vhost \
--vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
-5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+5. Check the virtio-user side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
@@ -205,19 +213,21 @@ Test Case 4: loopback reconnect test with split ring inorder mergeable path and
--vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,mrg_rxbuf=1,in_order=1\
-- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
-9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+9. Check the vhost side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
testpmd>show port stats all
-10. Port restart at vhost side by below command and re-calculate the average throughput::
+10. Port restart at vhost side by below command and check throughput can get expected::
testpmd>stop
testpmd>port stop 0
testpmd>port start 0
+ testpmd>set txpkts 2000,2000,2000,2000
testpmd>start tx_first 32
testpmd>show port stats all
@@ -236,13 +246,14 @@ Test Case 5: loopback reconnect test with split ring inorder non-mergeable path
>set fwd mac
>start
-2. Launch virtio-user as server mode with 2 queues::
+2. Launch virtio-user as server mode with 2 queues check throughput can get expected::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
--vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,mrg_rxbuf=0,in_order=1 \
-- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
>start tx_first 32
+ >show port stats all
3. Quit vhost side testpmd, check the virtio-user side link status::
@@ -256,7 +267,7 @@ Test Case 5: loopback reconnect test with split ring inorder non-mergeable path
>set fwd mac
>start tx_first 32
-5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+5. Check the virtio-user side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
@@ -279,13 +290,13 @@ Test Case 5: loopback reconnect test with split ring inorder non-mergeable path
>set fwd mac
>start tx_first 32
-9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+9. Check the vhost side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
testpmd>show port stats all
-10. Port restart at vhost side by below command and re-calculate the average throughput::
+10. Port restart at vhost side by below command and check throughput can get expected::
testpmd>stop
testpmd>port stop 0
@@ -308,13 +319,14 @@ Test Case 6: loopback reconnect test with split ring non-mergeable path and serv
>set fwd mac
>start
-2. Launch virtio-user as server mode with 2 queues::
+2. Launch virtio-user as server mode with 2 queues and check throughput can get expected::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
--vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,mrg_rxbuf=0,in_order=0,vectorized=1 \
-- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
>start tx_first 32
+ >show port stats all
3. Quit vhost side testpmd, check the virtio-user side link status::
@@ -328,7 +340,7 @@ Test Case 6: loopback reconnect test with split ring non-mergeable path and serv
>set fwd mac
>start tx_first 32
-5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+5. Check the virtio-user side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
@@ -351,13 +363,13 @@ Test Case 6: loopback reconnect test with split ring non-mergeable path and serv
>set fwd mac
>start tx_first 32
-9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+9. Check the vhost side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
testpmd>show port stats all
-10. Port restart at vhost side by below command and re-calculate the average throughput::
+10. Port restart at vhost side by below command and check throughput can get expected::
testpmd>stop
testpmd>port stop 0
@@ -380,13 +392,14 @@ Test Case 7: loopback reconnect test with split ring vector_rx path and server m
>set fwd mac
>start
-2. Launch virtio-user as server mode with 2 queues::
+2. Launch virtio-user as server mode with 2 queues and check throughput can get expected::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
--vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,mrg_rxbuf=0,in_order=0,vectorized=1 \
-- -i --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
>start tx_first 32
+ >show port stats all
3. Quit vhost side testpmd, check the virtio-user side link status::
@@ -400,7 +413,7 @@ Test Case 7: loopback reconnect test with split ring vector_rx path and server m
>set fwd mac
>start tx_first 32
-5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+5. Check the virtio-user side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
@@ -423,13 +436,13 @@ Test Case 7: loopback reconnect test with split ring vector_rx path and server m
>set fwd mac
>start tx_first 32
-9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+9. Check the vhost side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
testpmd>show port stats all
-10. Port restart at vhost side by below command and re-calculate the average throughput::
+10. Port restart at vhost side by below command and check throughput can get expected::
testpmd>stop
testpmd>port stop 0
@@ -452,13 +465,15 @@ Test Case 8: loopback reconnect test with packed ring mergeable path and server
>set fwd mac
>start
-2. Launch virtio-user as server mode with 2 queues::
+2. Launch virtio-user as server mode with 2 queues and check throughput can get expected::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
--vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=1,in_order=0 \
-- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
+ >show port stats all
3. Quit vhost side testpmd, check the virtio-user side link status::
@@ -470,9 +485,10 @@ Test Case 8: loopback reconnect test with packed ring mergeable path and server
./testpmd -c 0xe -n 4 --no-pci --file-prefix=vhost \
--vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
-5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+5. Check the virtio-user side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
@@ -493,19 +509,21 @@ Test Case 8: loopback reconnect test with packed ring mergeable path and server
--vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=1,in_order=0 \
-- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
-9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+9. Check the vhost side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
testpmd>show port stats all
-10. Port restart at vhost side by below command and re-calculate the average throughput::
+10. Port restart at vhost side by below command and check throughput can get expected::
testpmd>stop
testpmd>port stop 0
testpmd>port start 0
+ testpmd>set txpkts 2000,2000,2000,2000
testpmd>start tx_first 32
testpmd>show port stats all
@@ -524,13 +542,14 @@ Test Case 9: loopback reconnect test with packed ring non-mergeable path and ser
>set fwd mac
>start
-2. Launch virtio-user as server mode with 2 queues::
+2. Launch virtio-user as server mode with 2 queues and check throughput can get expected::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
--vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=0,in_order=0 \
-- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
>start tx_first 32
+ >show port stats all
3. Quit vhost side testpmd, check the virtio-user side link status::
@@ -544,7 +563,7 @@ Test Case 9: loopback reconnect test with packed ring non-mergeable path and ser
>set fwd mac
>start tx_first 32
-5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+5. Check the virtio-user side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
@@ -567,13 +586,13 @@ Test Case 9: loopback reconnect test with packed ring non-mergeable path and ser
>set fwd mac
>start tx_first 32
-9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+9. Check the vhost side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
testpmd>show port stats all
-10. Port restart at vhost side by below command and re-calculate the average throughput::
+10. Port restart at vhost side by below command and check throughput can get expected::
testpmd>stop
testpmd>port stop 0
@@ -588,21 +607,23 @@ Test Case 9: loopback reconnect test with packed ring non-mergeable path and ser
Test Case 10: loopback reconnect test with packed ring inorder mergeable path and server mode
=============================================================================================
-1. launch vhost as client mode with 2 queues::
+1. launch vhost as client mode with 8 queues::
rm -rf vhost-net*
./testpmd -c 0xe -n 4 --no-pci --file-prefix=vhost \
- --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=8' -- -i --nb-cores=2 --rxq=8 --txq=8
>set fwd mac
>start
-2. Launch virtio-user as server mode with 2 queues::
+2. Launch virtio-user as server mode with 8 queues and check throughput can get expected::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
- --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=1,in_order=1 \
- -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=8,packed_vq=1,mrg_rxbuf=1,in_order=1 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=8 --txq=8
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
+ >show port stats all
3. Quit vhost side testpmd, check the virtio-user side link status::
@@ -612,11 +633,12 @@ Test Case 10: loopback reconnect test with packed ring inorder mergeable path an
4. Relaunch vhost and send packets::
./testpmd -c 0xe -n 4 --no-pci --file-prefix=vhost \
- --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=2' -- -i --nb-cores=2 --rxq=2 --txq=2
+ --vdev 'eth_vhost0,iface=vhost-net,client=1,queues=8' -- -i --nb-cores=2 --rxq=8 --txq=8
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
-5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+5. Check the virtio-user side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
@@ -634,22 +656,24 @@ Test Case 10: loopback reconnect test with packed ring inorder mergeable path an
8. Relaunch virtio-user and send packets::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
- --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=1,in_order=1 \
- -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
+ --vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=8,packed_vq=1,mrg_rxbuf=1,in_order=1 \
+ -- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=8 --txq=8
>set fwd mac
+ >set txpkts 2000,2000,2000,2000
>start tx_first 32
-9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+9. Check the vhost side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
testpmd>show port stats all
-10. Port restart at vhost side by below command and re-calculate the average throughput::
+10. Port restart at vhost side by below command and check throughput can get expected::
testpmd>stop
testpmd>port stop 0
testpmd>port start 0
+ testpmd>set txpkts 2000,2000,2000,2000
testpmd>start tx_first 32
testpmd>show port stats all
@@ -668,13 +692,14 @@ Test Case 11: loopback reconnect test with packed ring inorder non-mergeable pat
>set fwd mac
>start
-2. Launch virtio-user as server mode with 2 queues::
+2. Launch virtio-user as server mode with 2 queues and check throughput can get expected::
./testpmd -n 4 -l 5-7 --no-pci --file-prefix=virtio \
--vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=0,in_order=1,vectorized=1 \
-- -i --rx-offloads=0x10 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
>start tx_first 32
+ >show port stats all
3. Quit vhost side testpmd, check the virtio-user side link status::
@@ -688,7 +713,7 @@ Test Case 11: loopback reconnect test with packed ring inorder non-mergeable pat
>set fwd mac
>start tx_first 32
-5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+5. Check the virtio-user side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
@@ -711,13 +736,13 @@ Test Case 11: loopback reconnect test with packed ring inorder non-mergeable pat
>set fwd mac
>start tx_first 32
-9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+9. Check the vhost side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
testpmd>show port stats all
-10. Port restart at vhost side by below command and re-calculate the average throughput::
+10. Port restart at vhost side by below command and check throughput can get expected::
testpmd>stop
testpmd>port stop 0
@@ -740,13 +765,14 @@ Test Case 12: loopback reconnect test with packed ring vectorized path and serve
>set fwd mac
>start
-2. Launch virtio-user as server mode with 2 queues::
+2. Launch virtio-user as server mode with 2 queues and check throughput can get expected::
./testpmd -n 4 -l 5-7 --log-level=pmd.net.virtio.driver,8 --no-pci --file-prefix=virtio --force-max-simd-bitwidth=512 \
--vdev=net_virtio_user0,mac=00:01:02:03:04:05,path=./vhost-net,server=1,queues=2,packed_vq=1,mrg_rxbuf=0,in_order=1,vectorized=1 \
-- -i --tx-offloads=0x0 --enable-hw-vlan-strip --rss-ip --nb-cores=2 --rxq=2 --txq=2
>set fwd mac
>start tx_first 32
+ >show port stats all
3. Quit vhost side testpmd, check the virtio-user side link status::
@@ -760,7 +786,7 @@ Test Case 12: loopback reconnect test with packed ring vectorized path and serve
>set fwd mac
>start tx_first 32
-5. Check the virtio-user side link status and run below command to get throughput,verify the loopback throughput is not zero::
+5. Check the virtio-user side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
@@ -783,13 +809,13 @@ Test Case 12: loopback reconnect test with packed ring vectorized path and serve
>set fwd mac
>start tx_first 32
-9. Check the vhost side link status and run below command to get throughput, verify the loopback throughput is not zero::
+9. Check the vhost side link status and run below command to get throughput, check throughput can get expected::
testpmd> show port info 0
#it should show up"
testpmd>show port stats all
-10. Port restart at vhost side by below command and re-calculate the average throughput::
+10. Port restart at vhost side by below command and check throughput can get expected::
testpmd>stop
testpmd>port stop 0
--
2.33.1
next prev parent reply other threads:[~2021-11-23 7:46 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-11-23 15:46 [dts][PATCH V1 0/2] loopback_virtio_user_server_mode: modify for case coverage improvement Lingli Chen
2021-11-23 15:46 ` Lingli Chen [this message]
2021-11-23 15:46 ` [dts][PATCH V1 2/2] tests/loopback_virtio_user_server_mode: Modify case sync with testplan Lingli Chen
2021-11-23 7:48 ` Chen, LingliX
2021-11-25 2:28 ` Wang, Yinan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211123154648.129079-2-linglix.chen@intel.com \
--to=linglix.chen@intel.com \
--cc=dts@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).