* [dts] [PATCH v2] test_plans/vf_offload: correct case description and commands
@ 2019-03-18 3:35 Xueqin Lin
2019-03-24 18:32 ` Tu, Lijuan
0 siblings, 1 reply; 2+ messages in thread
From: Xueqin Lin @ 2019-03-18 3:35 UTC (permalink / raw)
To: dts; +Cc: Xueqin Lin
Signed-off-by: Xueqin Lin <xueqin.lin@intel.com>
---
test_plans/vf_offload_test_plan.rst | 90 +++++++++++++++++++++----------------
1 file changed, 51 insertions(+), 39 deletions(-)
diff --git a/test_plans/vf_offload_test_plan.rst b/test_plans/vf_offload_test_plan.rst
index 5313bc9..ee15dca 100644
--- a/test_plans/vf_offload_test_plan.rst
+++ b/test_plans/vf_offload_test_plan.rst
@@ -38,7 +38,7 @@ VF Offload
Prerequisites for checksum offload
==================================
-If using vfio the kernel must be >= 3.6+ and VT-d must be enabled in bios.When
+If using vfio the kernel must be >= 3.6+ and VT-d must be enabled in bios. When
using vfio, use the following commands to load the vfio driver and bind it
to the device under test::
@@ -46,12 +46,13 @@ to the device under test::
modprobe vfio-pci
usertools/dpdk-devbind.py --bind=vfio-pci device_bus_id
-Assuming that ports ``0`` and ``2`` are connected to a traffic generator,
+Assuming that ports ``0`` and ``1`` are connected to a traffic generator,
+enable hardware rx checksum offload with "--enable-rx-cksum",
launch the ``testpmd`` with the following arguments::
./build/app/testpmd -cffffff -n 1 -- -i --burst=1 --txpt`=32 \
--txht=8 --txwt=0 --txfreet=0 --rxfreet=64 --mbcache=250 --portmask=0x5
- enable-rx-cksum
+ --enable-rx-cksum
Set the verbose level to 1 to display information for each received packet::
@@ -84,20 +85,21 @@ Verify that how many packets found with Bad-ipcsum or Bad-l4csum::
Test Case: HW checksum offload check
====================================
-Start testpmd and enable checksum offload on tx port.
+Start testpmd and enable checksum offload on rx port.
Setup the ``csum`` forwarding mode::
testpmd> set fwd csum
Set csum packet forwarding mode
-Enable the IPv4/UDP/TCP/SCTP checksum offload on port 0::
+Enable the IPv4/UDP/TCP/SCTP HW checksum offload on port 0::
- testpmd>
- testpmd> tx_checksum set ip hw 0
- testpmd> tx_checksum set udp hw 0
- testpmd> tx_checksum set tcp hw 0
- testpmd> tx_checksum set sctp hw 0
+ testpmd> port stop all
+ testpmd> csum set ip hw 0
+ testpmd> csum set tcp hw 0
+ testpmd> csum set udp hw 0
+ testpmd> csum set sctp hw 0
+ testpmd> port start all
testpmd> start
csum packet forwarding - CRC stripping disabled - packets/burst=32
nb forwarding cores=1 - nb forwarding ports=10
@@ -110,9 +112,9 @@ Configure the traffic generator to send the multiple packets for the following
combination: IPv4/UDP, IPv4/TCP, IPv4/SCTP, IPv6/UDP, IPv6/TCP.
Send packets with incorrect checksum,
-Verify dpdk can rx it and reported the checksum error,
-Verify that the same number of packet are correctly received on the traffic
-generator side. And IPv4 checksum, TCP checksum, UDP checksum, SCTP CRC32c need
+verify dpdk can rx it and report the checksum error,
+verify that the same number of packet are correctly received on the traffic
+generator side. And IPv4 checksum, TCP checksum, UDP checksum, SCTP checksum need
be validated as pass by the tester.
The IPv4 source address will not be changed by testpmd.
@@ -121,17 +123,22 @@ The IPv4 source address will not be changed by testpmd.
Test Case: SW checksum offload check
====================================
-Disable HW checksum offload on tx port, SW Checksum check.
-Send same packet with incorrect checksum and verify checksum is valid.
+Enable SW checksum offload, send same packet with incorrect checksum
+and verify checksum is valid.
Setup the ``csum`` forwarding mode::
testpmd> set fwd csum
Set csum packet forwarding mode
-Disable the IPv4/UDP/TCP/SCTP checksum offload on port 0::
+Enable the IPv4/UDP/TCP/SCTP SW checksum offload on port 0::
- testpmd> tx_checksum set 0x0 0
+ testpmd> port stop all
+ testpmd> csum set ip sw 0
+ testpmd> csum set tcp sw 0
+ testpmd> csum set udp sw 0
+ testpmd> csum set sctp sw 0
+ testpmd> port start all
testpmd> start
csum packet forwarding - CRC stripping disabled - packets/burst=32
nb forwarding cores=1 - nb forwarding ports=10
@@ -144,12 +151,12 @@ Configure the traffic generator to send the multiple packets for the following
combination: IPv4/UDP, IPv4/TCP, IPv6/UDP, IPv6/TCP.
Send packets with incorrect checksum,
-Verify dpdk can rx it and reported the checksum error,
-Verify that the same number of packet are correctly received on the traffic
+verify dpdk can rx it and report the checksum error,
+verify that the same number of packet are correctly received on the traffic
generator side. And IPv4 checksum, TCP checksum, UDP checksum need
-be validated as pass by the IXIA.
+be validated as pass by the tester.
-The first byte of source IPv4 address will be increment by testpmd. The checksum
+The first byte of source IPv4 address will be increased by testpmd. The checksum
is indeed recalculated by software algorithms.
Prerequisites for TSO
@@ -169,15 +176,17 @@ On tester, all offload feature should be disabled on tx port, and start rx port
On DUT, run pmd with parameter "--enable-rx-cksum". Then enable TSO on tx port
and checksum on rx port. The test commands is below::
- #enable hw checksum on rx port
- tx_checksum set ip hw 0
- tx_checksum set udp hw 0
- tx_checksum set tcp hw 0
- tx_checksum set sctp hw 0
- set fwd csum
+ # Enable hw checksum on rx port
+ testpmd> port stop all
+ testpmd> csum set ip hw 0
+ testpmd> csum set tcp hw 0
+ testpmd> csum set udp hw 0
+ testpmd> csum set sctp hw 0
+ testpmd> port start all
+ testpmd> set fwd csum
- # enable TSO on tx port
- *tso set 800 1
+ # Enable TSO on tx port
+ testpmd> tso set 800 1
Test case: csum fwd engine, use TSO
@@ -192,22 +201,25 @@ Turn off tx port by ethtool on tester::
ethtool -K <tx port> rx off tx off tso off gso off gro off lro off
ip l set <tx port> up
-capture package rx port on tester::
+Capture package rx port on tester::
tcpdump -n -e -i <rx port> -s 0 -w /tmp/cap
Launch the userland ``testpmd`` application on DUT as follows::
testpmd> set verbose 1
-
- # enable hw checksum on rx port
- testpmd> tx_checksum set ip hw 0
- testpmd> tx_checksum set udp hw 0
- testpmd> tx_checksum set tcp hw 0
- testpmd> tx_checksum set sctp hw 0
- # enable TSO on tx port
+ # Enable hw checksum on rx port
+ testpmd> port stop all
+ testpmd> csum set ip hw 0
+ testpmd> csum set tcp hw 0
+ testpmd> csum set udp hw 0
+ testpmd> csum set sctp hw 0
+ testpmd> port start all
+
+ # Enable TSO on tx port
testpmd> tso set 800 1
- # set fwd engine and start
+ # Set fwd engine and start
+
testpmd> set fwd csum
testpmd> start
@@ -217,4 +229,4 @@ Test IPv4() in scapy::
Test IPv6() in scapy::
- sendp([Ether(dst="%s", src="52:00:00:00:00:00")/IPv6(src="FE80:0:0:0:200:1FF:FE00:200", dst="3555:5555:6666:6666:7777:7777:8888:8888")/UDP(sport=1021,dport=1021)/Raw(load="\x50"*%s)], iface="%s"
+ sendp([Ether(dst="%s", src="52:00:00:00:00:00")/IPv6(src="FE80:0:0:0:200:1FF:FE00:200", dst="3555:5555:6666:6666:7777:7777:8888:8888")/UDP(sport=1021,dport=1021)/Raw(load="\x50"*%s)], iface="%s")
--
2.5.5
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [dts] [PATCH v2] test_plans/vf_offload: correct case description and commands
2019-03-18 3:35 [dts] [PATCH v2] test_plans/vf_offload: correct case description and commands Xueqin Lin
@ 2019-03-24 18:32 ` Tu, Lijuan
0 siblings, 0 replies; 2+ messages in thread
From: Tu, Lijuan @ 2019-03-24 18:32 UTC (permalink / raw)
To: Lin, Xueqin, dts; +Cc: Lin, Xueqin
Applied, thanks
> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of Xueqin Lin
> Sent: Sunday, March 17, 2019 8:36 PM
> To: dts@dpdk.org
> Cc: Lin, Xueqin <xueqin.lin@intel.com>
> Subject: [dts] [PATCH v2] test_plans/vf_offload: correct case description and
> commands
>
> Signed-off-by: Xueqin Lin <xueqin.lin@intel.com>
>
> ---
> test_plans/vf_offload_test_plan.rst | 90 +++++++++++++++++++++----------------
> 1 file changed, 51 insertions(+), 39 deletions(-)
>
> diff --git a/test_plans/vf_offload_test_plan.rst
> b/test_plans/vf_offload_test_plan.rst
> index 5313bc9..ee15dca 100644
> --- a/test_plans/vf_offload_test_plan.rst
> +++ b/test_plans/vf_offload_test_plan.rst
> @@ -38,7 +38,7 @@ VF Offload
> Prerequisites for checksum offload
> ==================================
>
> -If using vfio the kernel must be >= 3.6+ and VT-d must be enabled in bios.When
> +If using vfio the kernel must be >= 3.6+ and VT-d must be enabled in
> +bios. When
> using vfio, use the following commands to load the vfio driver and bind it to the
> device under test::
>
> @@ -46,12 +46,13 @@ to the device under test::
> modprobe vfio-pci
> usertools/dpdk-devbind.py --bind=vfio-pci device_bus_id
>
> -Assuming that ports ``0`` and ``2`` are connected to a traffic generator,
> +Assuming that ports ``0`` and ``1`` are connected to a traffic
> +generator, enable hardware rx checksum offload with
> +"--enable-rx-cksum",
> launch the ``testpmd`` with the following arguments::
>
> ./build/app/testpmd -cffffff -n 1 -- -i --burst=1 --txpt`=32 \
> --txht=8 --txwt=0 --txfreet=0 --rxfreet=64 --mbcache=250 --portmask=0x5
> - enable-rx-cksum
> + --enable-rx-cksum
>
> Set the verbose level to 1 to display information for each received packet::
>
> @@ -84,20 +85,21 @@ Verify that how many packets found with Bad-ipcsum or
> Bad-l4csum::
>
> Test Case: HW checksum offload check
> ====================================
> -Start testpmd and enable checksum offload on tx port.
> +Start testpmd and enable checksum offload on rx port.
>
> Setup the ``csum`` forwarding mode::
>
> testpmd> set fwd csum
> Set csum packet forwarding mode
>
> -Enable the IPv4/UDP/TCP/SCTP checksum offload on port 0::
> +Enable the IPv4/UDP/TCP/SCTP HW checksum offload on port 0::
>
> - testpmd>
> - testpmd> tx_checksum set ip hw 0
> - testpmd> tx_checksum set udp hw 0
> - testpmd> tx_checksum set tcp hw 0
> - testpmd> tx_checksum set sctp hw 0
> + testpmd> port stop all
> + testpmd> csum set ip hw 0
> + testpmd> csum set tcp hw 0
> + testpmd> csum set udp hw 0
> + testpmd> csum set sctp hw 0
> + testpmd> port start all
> testpmd> start
> csum packet forwarding - CRC stripping disabled - packets/burst=32
> nb forwarding cores=1 - nb forwarding ports=10 @@ -110,9 +112,9 @@
> Configure the traffic generator to send the multiple packets for the following
> combination: IPv4/UDP, IPv4/TCP, IPv4/SCTP, IPv6/UDP, IPv6/TCP.
>
> Send packets with incorrect checksum,
> -Verify dpdk can rx it and reported the checksum error, -Verify that the same
> number of packet are correctly received on the traffic -generator side. And IPv4
> checksum, TCP checksum, UDP checksum, SCTP CRC32c need
> +verify dpdk can rx it and report the checksum error, verify that the
> +same number of packet are correctly received on the traffic generator
> +side. And IPv4 checksum, TCP checksum, UDP checksum, SCTP checksum need
> be validated as pass by the tester.
>
> The IPv4 source address will not be changed by testpmd.
> @@ -121,17 +123,22 @@ The IPv4 source address will not be changed by
> testpmd.
> Test Case: SW checksum offload check
> ====================================
>
> -Disable HW checksum offload on tx port, SW Checksum check.
> -Send same packet with incorrect checksum and verify checksum is valid.
> +Enable SW checksum offload, send same packet with incorrect checksum
> +and verify checksum is valid.
>
> Setup the ``csum`` forwarding mode::
>
> testpmd> set fwd csum
> Set csum packet forwarding mode
>
> -Disable the IPv4/UDP/TCP/SCTP checksum offload on port 0::
> +Enable the IPv4/UDP/TCP/SCTP SW checksum offload on port 0::
>
> - testpmd> tx_checksum set 0x0 0
> + testpmd> port stop all
> + testpmd> csum set ip sw 0
> + testpmd> csum set tcp sw 0
> + testpmd> csum set udp sw 0
> + testpmd> csum set sctp sw 0
> + testpmd> port start all
> testpmd> start
> csum packet forwarding - CRC stripping disabled - packets/burst=32
> nb forwarding cores=1 - nb forwarding ports=10 @@ -144,12 +151,12 @@
> Configure the traffic generator to send the multiple packets for the following
> combination: IPv4/UDP, IPv4/TCP, IPv6/UDP, IPv6/TCP.
>
> Send packets with incorrect checksum,
> -Verify dpdk can rx it and reported the checksum error, -Verify that the same
> number of packet are correctly received on the traffic
> +verify dpdk can rx it and report the checksum error, verify that the
> +same number of packet are correctly received on the traffic
> generator side. And IPv4 checksum, TCP checksum, UDP checksum need -be
> validated as pass by the IXIA.
> +be validated as pass by the tester.
>
> -The first byte of source IPv4 address will be increment by testpmd. The
> checksum
> +The first byte of source IPv4 address will be increased by testpmd. The
> +checksum
> is indeed recalculated by software algorithms.
>
> Prerequisites for TSO
> @@ -169,15 +176,17 @@ On tester, all offload feature should be disabled on tx
> port, and start rx port On DUT, run pmd with parameter "--enable-rx-cksum".
> Then enable TSO on tx port and checksum on rx port. The test commands is
> below::
>
> - #enable hw checksum on rx port
> - tx_checksum set ip hw 0
> - tx_checksum set udp hw 0
> - tx_checksum set tcp hw 0
> - tx_checksum set sctp hw 0
> - set fwd csum
> + # Enable hw checksum on rx port
> + testpmd> port stop all
> + testpmd> csum set ip hw 0
> + testpmd> csum set tcp hw 0
> + testpmd> csum set udp hw 0
> + testpmd> csum set sctp hw 0
> + testpmd> port start all
> + testpmd> set fwd csum
>
> - # enable TSO on tx port
> - *tso set 800 1
> + # Enable TSO on tx port
> + testpmd> tso set 800 1
>
>
> Test case: csum fwd engine, use TSO
> @@ -192,22 +201,25 @@ Turn off tx port by ethtool on tester::
> ethtool -K <tx port> rx off tx off tso off gso off gro off lro off
> ip l set <tx port> up
>
> -capture package rx port on tester::
> +Capture package rx port on tester::
>
> tcpdump -n -e -i <rx port> -s 0 -w /tmp/cap
>
> Launch the userland ``testpmd`` application on DUT as follows::
>
> testpmd> set verbose 1
> -
> - # enable hw checksum on rx port
> - testpmd> tx_checksum set ip hw 0
> - testpmd> tx_checksum set udp hw 0
> - testpmd> tx_checksum set tcp hw 0
> - testpmd> tx_checksum set sctp hw 0
> - # enable TSO on tx port
> + # Enable hw checksum on rx port
> + testpmd> port stop all
> + testpmd> csum set ip hw 0
> + testpmd> csum set tcp hw 0
> + testpmd> csum set udp hw 0
> + testpmd> csum set sctp hw 0
> + testpmd> port start all
> +
> + # Enable TSO on tx port
> testpmd> tso set 800 1
> - # set fwd engine and start
> + # Set fwd engine and start
> +
> testpmd> set fwd csum
> testpmd> start
>
> @@ -217,4 +229,4 @@ Test IPv4() in scapy::
>
> Test IPv6() in scapy::
>
> - sendp([Ether(dst="%s",
> src="52:00:00:00:00:00")/IPv6(src="FE80:0:0:0:200:1FF:FE00:200",
> dst="3555:5555:6666:6666:7777:7777:8888:8888")/UDP(sport=1021,dport=102
> 1)/Raw(load="\x50"*%s)], iface="%s"
> + sendp([Ether(dst="%s",
> + src="52:00:00:00:00:00")/IPv6(src="FE80:0:0:0:200:1FF:FE00:200",
> + dst="3555:5555:6666:6666:7777:7777:8888:8888")/UDP(sport=1021,dport=10
> + 21)/Raw(load="\x50"*%s)], iface="%s")
> --
> 2.5.5
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2019-03-24 18:32 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-03-18 3:35 [dts] [PATCH v2] test_plans/vf_offload: correct case description and commands Xueqin Lin
2019-03-24 18:32 ` Tu, Lijuan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).