[dts] [PATCH]test_plans: add a test case to TestSuite_vlan.py

[dts] [PATCH]test_plans: add a test case to TestSuite_vlan.py

[Peng Yuan]

add "Enable receipt of VLAN packets and disable VLAN header stripping" to TestSuite_vlan.py

Signed-off-by: Peng Yuan <yuan.peng@intel.com>

diff --git a/test_plans/vlan_test_plan.rst b/test_plans/vlan_test_plan.rst
index beaab9b..a5058f8 100644
--- a/test_plans/vlan_test_plan.rst
+++ b/test_plans/vlan_test_plan.rst
@@ -76,10 +76,10 @@ The -n command is used to select the number of memory channels. It should match
 Set the verbose level to 1 to display information for each received packet::
 
   testpmd> set verbose 1
+  testpmd> vlan set filter on
 
-
-Test Case: Enable receipt of VLAN packets and VLAN header stripping
-===================================================================
+Test Case: Enable receipt of VLAN packets and disable VLAN header stripping
+===========================================================================
 
 Setup the ``mac`` forwarding mode::
 
@@ -89,6 +89,7 @@ Setup the ``mac`` forwarding mode::
 Enable the receipt of VLAN packets with VLAN Tag Identifier 1 on port 0::
 
   testpmd> rx_vlan add 1 0
+  testpmd> vlan set strip off 0
   testpmd> start
     rxonly packet forwarding - CRC stripping disabled - packets/burst=32
     nb forwarding cores=1 - nb forwarding ports=10
@@ -108,6 +109,31 @@ Identifier and send 1 packet on port ``A``.
 Verify that the VLAN packet was not correctly received on port ``B`` with
 this not matched VLAN Tag.
 
+Test Case: Enable receipt of VLAN packets and VLAN header stripping
+===================================================================
+
+Setup the ``mac`` forwarding mode::
+
+  testpmd> set fwd mac
+  Set mac packet forwarding mode
+
+Enable the receipt of VLAN packets with VLAN Tag Identifier 1 on port 0::
+
+  testpmd> rx_vlan add 1 0
+  testpmd> vlan set strip on 0
+  testpmd> start
+    rxonly packet forwarding - CRC stripping disabled - packets/burst=32
+    nb forwarding cores=1 - nb forwarding ports=10
+    RX queues=1 - RX desc=128 - RX free threshold=64
+    RX threshold registers: pthresh=8 hthresh=8 wthresh=4
+    TX queues=1 - TX desc=512 - TX free threshold=0
+    TX threshold registers: pthresh=32 hthresh=8 wthresh=8
+
+Configure the traffic generator to send VLAN packets with the Tag Identifier
+ ``1`` and send 1 packet on port ``A``.
+
+Verify that the VLAN packet was correctly received on port ``B`` without VLAN tag ``1``.
+
 Test Case: Disable receipt of VLAN packets
 ==========================================
 
-- 
2.14.3

Re: [dts] [PATCH]test_plans: add a test case to TestSuite_vlan.py

[Tu, Lijuan]

Applied, thanks

> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of Peng Yuan
> Sent: Tuesday, July 23, 2019 2:10 PM
> To: dts@dpdk.org
> Cc: Peng, Yuan <yuan.peng@intel.com>
> Subject: [dts] [PATCH]test_plans: add a test case to TestSuite_vlan.py
> 
> add "Enable receipt of VLAN packets and disable VLAN header stripping" to
> TestSuite_vlan.py
> 
> Signed-off-by: Peng Yuan <yuan.peng@intel.com>
> 
> diff --git a/test_plans/vlan_test_plan.rst b/test_plans/vlan_test_plan.rst
> index beaab9b..a5058f8 100644
> --- a/test_plans/vlan_test_plan.rst
> +++ b/test_plans/vlan_test_plan.rst
> @@ -76,10 +76,10 @@ The -n command is used to select the number of
> memory channels. It should match  Set the verbose level to 1 to display
> information for each received packet::
> 
>    testpmd> set verbose 1
> +  testpmd> vlan set filter on
> 
> -
> -Test Case: Enable receipt of VLAN packets and VLAN header stripping -
> ================================================================
> ===
> +Test Case: Enable receipt of VLAN packets and disable VLAN header
> +stripping
> +===============================================================
> ========
> +====
> 
>  Setup the ``mac`` forwarding mode::
> 
> @@ -89,6 +89,7 @@ Setup the ``mac`` forwarding mode::
>  Enable the receipt of VLAN packets with VLAN Tag Identifier 1 on port 0::
> 
>    testpmd> rx_vlan add 1 0
> +  testpmd> vlan set strip off 0
>    testpmd> start
>      rxonly packet forwarding - CRC stripping disabled - packets/burst=32
>      nb forwarding cores=1 - nb forwarding ports=10 @@ -108,6 +109,31 @@
> Identifier and send 1 packet on port ``A``.
>  Verify that the VLAN packet was not correctly received on port ``B`` with
> this not matched VLAN Tag.
> 
> +Test Case: Enable receipt of VLAN packets and VLAN header stripping
> +===============================================================
> ====
> +
> +Setup the ``mac`` forwarding mode::
> +
> +  testpmd> set fwd mac
> +  Set mac packet forwarding mode
> +
> +Enable the receipt of VLAN packets with VLAN Tag Identifier 1 on port 0::
> +
> +  testpmd> rx_vlan add 1 0
> +  testpmd> vlan set strip on 0
> +  testpmd> start
> +    rxonly packet forwarding - CRC stripping disabled - packets/burst=32
> +    nb forwarding cores=1 - nb forwarding ports=10
> +    RX queues=1 - RX desc=128 - RX free threshold=64
> +    RX threshold registers: pthresh=8 hthresh=8 wthresh=4
> +    TX queues=1 - TX desc=512 - TX free threshold=0
> +    TX threshold registers: pthresh=32 hthresh=8 wthresh=8
> +
> +Configure the traffic generator to send VLAN packets with the Tag
> +Identifier  ``1`` and send 1 packet on port ``A``.
> +
> +Verify that the VLAN packet was correctly received on port ``B`` without
> VLAN tag ``1``.
> +
>  Test Case: Disable receipt of VLAN packets
> ==========================================
> 
> --
> 2.14.3