Re: [dts] [PATCH V1] test_plans: add test plan port controls

["Tu, Lijuan" <lijuan.tu@intel.com>]

Applied, thanks

> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of Nannan Lu
> Sent: Friday, December 6, 2019 11:57 PM
> To: dts@dpdk.org
> Cc: Lu, Nannan <nannan.lu@intel.com>
> Subject: [dts] [PATCH V1] test_plans: add test plan port controls
> 
> Signed-off-by: Nannan Lu <nannan.lu@intel.com>
> ---
>  test_plans/port_control_test_plan.rst | 257 ++++++++++++++++++++++++++
>  1 file changed, 257 insertions(+)
>  create mode 100644 test_plans/port_control_test_plan.rst
> 
> diff --git a/test_plans/port_control_test_plan.rst
> b/test_plans/port_control_test_plan.rst
> new file mode 100644
> index 0000000..2fca8fd
> --- /dev/null
> +++ b/test_plans/port_control_test_plan.rst
> @@ -0,0 +1,257 @@
> +.. Copyright (c) <2019>, Intel Corporation
> +   All rights reserved.
> +
> +   Redistribution and use in source and binary forms, with or without
> +   modification, are permitted provided that the following conditions
> +   are met:
> +
> +   - Redistributions of source code must retain the above copyright
> +     notice, this list of conditions and the following disclaimer.
> +
> +   - Redistributions in binary form must reproduce the above copyright
> +     notice, this list of conditions and the following disclaimer in
> +     the documentation and/or other materials provided with the
> +     distribution.
> +
> +   - Neither the name of Intel Corporation nor the names of its
> +     contributors may be used to endorse or promote products derived
> +     from this software without specific prior written permission.
> +
> +   THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
> CONTRIBUTORS
> +   "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
> +   LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
> FITNESS
> +   FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
> +   COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
> INDIRECT,
> +   INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> +   (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
> GOODS OR
> +   SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
> +   HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
> CONTRACT,
> +   STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
> +   ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
> ADVISED
> +   OF THE POSSIBILITY OF SUCH DAMAGE.
> +
> +==================
> +Port Control Tests
> +==================
> +
> +
> +Prerequisites
> +=============
> +
> +1. Hardware:
> +
> +   * Fortville
> +   * Niantic
> +   * Columbiaville
> +   * i350 NIC
> +   * e1000 emulated device
> +
> +
> +Test Case: pf start/stop/reset/close
> +====================================
> +
> +1. Bind the port to dpdk driver::
> +
> +     ./usertools/dpdk-devbind.py -b igb_uio 18:00.2
> +
> +2. Run testpmd::
> +
> +     ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xff -n 4 -- -i
> +
> +     testpmd> set fwd mac
> +     testpmd> start
> +
> +   check port info::
> +
> +     testpmd> show port info all
> +
> +     ********************* Infos for port 0  *********************
> +     Link status: up
> +     Link speed: 1000 Mbps
> +
> +   verify that the link status is up.
> +
> +   Using scapy to send 1000 random packets from tester,
> +   verify the packets can be received and can be forwarded::
> +
> +     scapy
> +     >>>sendp([Ether(dst="00:11:22:33:44:11")/IP()/Raw('x'*40)], \
> +     iface="enp27s0f2",count=1000)
> +
> +3. Stop and start port::
> +
> +     testpmd> stop
> +     testpmd> port stop all
> +     testpmd> show port info all
> +
> +     ********************* Infos for port 0  *********************
> +     Link status: down
> +     Link speed: 0 Mbps
> +
> +  verify that the link status is down.
> +
> +  Then start the port::
> +
> +    testpmd> port start all
> +    testpmd> start
> +
> +  check port info::
> +
> +    testpmd> show port info all
> +
> +    ********************* Infos for port 0  *********************
> +    Link status: up
> +    Link speed: 10000 Mbps
> +
> +  verify that the link status is up.
> +
> +  Send the same 1000 packets with scapy from tester,  verify the
> + packets can be received and forwarded.
> +
> +4. Reset the port, run the commands::
> +
> +     testpmd> stop
> +     testpmd> port stop all
> +     testpmd> port reset all
> +     testpmd> show port info all
> +
> +     ********************* Infos for port 0  *********************
> +     Link status: down
> +     Link speed: 0 Mbps
> +
> +   verify that the link status is down.
> +
> +   Then start the port::
> +
> +     testpmd> port start all
> +     testpmd> start
> +
> +   check port info::
> +
> +     testpmd> show port info all
> +
> +     ********************* Infos for port 0  *********************
> +     Link status: up
> +     Link speed: 10000 Mbps
> +
> +   verify that the link status is up.
> +   Send the same 1000 packets with scapy from tester,
> +   verify the packets can be received and forwarded.
> +
> +5. Close the port, run the commands::
> +
> +     testpmd> stop
> +     testpmd> port stop all
> +     testpmd> port close all
> +
> +   check the port info::
> +
> +     testpmd> show port info all
> +     testpmd>
> +
> +   verify that there is no output after executing this command.
> +
> +
> +Test Case: e1000 emulated device start/stop/reset/close
> +=======================================================
> +
> +1. Set up qemu environment
> +
> +   Virtual an e1000 emulated device in vm, then start
> +   vm with the following command::
> +
> +     qemu-system-x86_64 -enable-kvm -m 16G -vnc :20 \
> +     -smp cores=10,sockets=1 -cpu host -hda ./u18.img \
> +     -device e1000,netdev=net1,mac=00:01:02:33:44:22 \
> +     -netdev user,id=net1,hostfwd=tcp:10.67.119.144:6666-:22 \
> +     -device e1000,netdev=net2,mac=00:01:02:33:44:33 \
> +     -netdev user,id=net2,hostfwd=tcp:10.67.119.144:7777-:23 \
> +     -monitor stdio
> +
> +   Login vm, get the pci device id of the e1000 emulated device,
> +   assume it is 0000:00:03.0, bind it to igb_uio driver, and then
> +   start testpmd::
> +
> +     ./usertools/dpdk-devbind.py -b igb_uio 0000:00:03.0
> +     ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -- -i
> +
> +     testpmd-> set fwd mac
> +     testpmd-> start
> +
> +   check port info::
> +
> +     testpmd> show port info all
> +
> +     ********************* Infos for port 0  *********************
> +     Link status: up
> +     Link speed: 1000 Mbps
> +
> +   verify that the link status is up.
> +
> +2. Stop and start port (not support)::
> +
> +     testpmd> stop
> +     testpmd> port stop all
> +     testpmd> show port info all
> +
> +     ********************* Infos for port 0  *********************
> +     Link status: down
> +     Link speed: 0 Mbps
> +
> +   verify that the link status is down.
> +
> +   Then start the port::
> +
> +     testmd-> port start all
> +     testpmd> start
> +
> +   check the port info::
> +
> +      testpmd> show port info all
> +
> +      ********************* Infos for port 0  *********************
> +      Link status: up
> +      Link speed: 10000 Mbps
> +
> +   verify that the link status is up.
> +
> +3. Reset the port (not support)::
> +
> +     testpmd> stop
> +     testpmd> port stop all
> +     testpmd> port reset all
> +     testpmd> show port info all
> +
> +     ********************* Infos for port 0  *********************
> +     Link status: down
> +     Link speed: 0 Mbps
> +
> +   verify that the link status is down.
> +
> +   Then start the port::
> +
> +     testpmd> port start all
> +     testpmd> start
> +
> +   check the port info::
> +
> +      testpmd> show port info all
> +
> +      ********************* Infos for port 0  *********************
> +      Link status: up
> +      Link speed: 10000 Mbps
> +
> +   verify that the link status is up.
> +
> +4. Close the port::
> +
> +     testpmd> stop
> +     testpmd> port stop all
> +     testpmd> port close all
> +
> +   check the port info::
> +
> +     testpmd> show port info all
> +     testpmd>
> +
> +   verify that there is no output after executing this command.
> --
> 2.17.1