* Re: [dts] [PATCH V3]test_plans: add test plan for rte_flow priority
2019-12-27 16:14 [dts] [PATCH V3]test_plans: add test plan for rte_flow priority qifu
@ 2019-12-27 8:08 ` Tu, Lijuan
0 siblings, 0 replies; 2+ messages in thread
From: Tu, Lijuan @ 2019-12-27 8:08 UTC (permalink / raw)
To: Fu, Qi, dts; +Cc: Fu, Qi
applied
> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of qifu
> Sent: Saturday, December 28, 2019 12:15 AM
> To: dts@dpdk.org
> Cc: Fu, Qi <qi.fu@intel.com>
> Subject: [dts] [PATCH V3]test_plans: add test plan for rte_flow priority
>
> Add test plan for cvl rteflow priority.
>
> Signed-off-by: qifu <qi.fu@intel.com>
> ---
> test_plans/rteflow_priority_test_plan.rst | 338 ++++++++++++++++++++++
> 1 file changed, 338 insertions(+)
> create mode 100644 test_plans/rteflow_priority_test_plan.rst
>
> diff --git a/test_plans/rteflow_priority_test_plan.rst
> b/test_plans/rteflow_priority_test_plan.rst
> new file mode 100644
> index 0000000..b853e90
> --- /dev/null
> +++ b/test_plans/rteflow_priority_test_plan.rst
> @@ -0,0 +1,338 @@
> +.. Copyright (c) <2019>, Intel Corporation
> + All rights reserved.
> +
> + Redistribution and use in source and binary forms, with or without
> + modification, are permitted provided that the following conditions
> + are met:
> +
> + - Redistributions of source code must retain the above copyright
> + notice, this list of conditions and the following disclaimer.
> +
> + - Redistributions in binary form must reproduce the above copyright
> + notice, this list of conditions and the following disclaimer in
> + the documentation and/or other materials provided with the
> + distribution.
> +
> + - Neither the name of Intel Corporation nor the names of its
> + contributors may be used to endorse or promote products derived
> + from this software without specific prior written permission.
> +
> + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
> CONTRIBUTORS
> + "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
> + LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
> FITNESS
> + FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
> + COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
> INDIRECT,
> + INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> + (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
> GOODS OR
> + SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
> + HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
> CONTRACT,
> + STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
> + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
> ADVISED
> + OF THE POSSIBILITY OF SUCH DAMAGE.
> +
> +
> +=======================
> +Rte_flow Priority Tests
> +=======================
> +
> +
> +Description
> +===========
> +
> +This document provides the plan for testing the Rte_flow Priority feature.
> +this feature uses devargs as a hint to active flow priority or not.
> +
> +This test plan is based on Intel E810 series ethernet cards.
> +when priority is not active, flows are created on fdir then switch/ACL.
> +when priority is active, flows are identified into 2 category:
> +High priority as permission stage that maps to switch/ACL, Low priority
> +as distribution stage that maps to fdir, a no destination high priority
> +rule is not acceptable, since it may be overwritten by a low priority rule due
> to cvl FXP behavior.
> +
> +Note: Since these tests are focus on priority, the patterns in tests are
> examples.
> +
> +
> +Prerequisites
> +=============
> +
> +Bind the pf to dpdk driver::
> +
> + ./usertools/dpdk-devbind.py -b vfio-pci af:00.0
> +
> +Note: The kernel must be >= 3.6+ and VT-d must be enabled in bios.
> +
> +Test Case: Setting Priority in Non-pipeline Mode
> +================================================
> +
> +Priority is not active in non-pipeline mode. The default value of priority is 0
> but it will be ignored.
> +
> +Patterns in this case:
> + MAC_IPV4
> +
> +#. Start the ``testpmd`` application as follows::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 0000:af:00.0 --
> log-level="ice,7" -- -i --txq=8 --rxq=8
> + set fwd rxonly
> + set verbose 1
> +
> +#. Create a rule with priority 0, Check the flow can be created but it will map
> to fdir filter::
> +
> + testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / end
> + ice_interrupt_handler(): OICR: MDD event
> + ice_flow_create(): Succeeded to create (1) flow
> + Flow rule #0 created
> +
> +#. Create a rule with priority 1, check the flow can not be created for the
> vallue of priority is 0 in non-pipeline mode::
> +
> + testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / end
> + ice_flow_create(): Failed to create flow
> + Caught error type 4 (priority field): cause: 0x7ffe24e65738, Not
> + support priority.: Invalid argument
> +
> +#. Start the ``testpmd`` application as follows::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w
> 0000:af:00.0,pipeline-mode-support=0 --log-level="ice,7" -- -i --txq=8 --rxq=8
> + set fwd rxonly
> + set verbose 1
> +
> +#. Create a rule with priority 0, Check the flow can be created but it will map
> to fdir filter::
> +
> + testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / end
> + ice_interrupt_handler(): OICR: MDD event
> + ice_flow_create(): Succeeded to create (1) flow
> + Flow rule #0 created
> +
> +#. Create a rule with priority 1, check the flow can not be created for the
> vallue of priority is 0 in non-pipeline mode::
> +
> + testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / end
> + ice_flow_create(): Failed to create flow
> + Caught error type 4 (priority field): cause: 0x7ffe24e65738, Not
> + support priority.: Invalid argument
> +
> +Test Case: Create Flow Rules with Priority in Pipeline Mode
> +============================================================
> +
> +Priority is active in pipeline mode.
> +Creating flow rules and setting priority 0/1 will map switch/fdir filter
> separately.
> +
> +Patterns in this case:
> + MAC_IPV4_TCP
> + MAC_IPV4_VXLAN_IPV4_UDP_PAY
> +
> +#. Start the ``testpmd`` application as follows::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w
> 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
> + set fwd rxonly
> + set verbose 1
> + rx_vxlan_port add 4789 0
> +
> +#. Create switch filter rules::
> +
> + flow create 0 priority 0 ingress pattern eth / ipv4 src is
> + 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 /
> + end actions queue index 1 / end
> +
> + flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan /
> + eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / udp src is
> + 25 dst is 23 / end actions queue index 2 / end
> +
> +#. Create fdir filter rules::
> +
> + flow create 0 priority 1 ingress pattern eth / ipv4 src is
> + 192.168.0.4 dst is 192.168.0.7 tos is 4 ttl is 20 / tcp src is 25 dst
> + is 23 / end actions queue index 3 / end
> +
> + flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan /
> + eth / ipv4 src is 192.168.0.4 dst is 192.168.0.7 / udp src is 25 dst
> + is 23 / end actions queue index 4 / end
> +
> +#. Check flow list with commands "flow list 0", all flows are created
> correctly::
> +
> + +-----+--------+--------+--------+-----------------------+
> + |ID | Group | Prio | Attr | Rul |
> + +=====+========+========+========+=======================+
> + | 0 | 0 | 0 | i- | ETH IPV4 TCP => QUEUE |
> + +-----+--------+--------+--------+-----------------------+
> + | 1 ... |
> + +-----+--------+--------+--------+-----------------------+
> + | 2 ... |
> + +-----+--------+--------+--------+-----------------------+
> + | 3 ... |
> + +-----+--------+--------+--------+-----------------------+
> +
> +#. Send packets according to the created rules in tester::
> +
> +
> sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.1
> 68.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface
> ="enp134s0f0")
> +
> sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP()/UDP()/V
> XLAN()/Ether()/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/UDP(sport=25,
> dport=23)/Raw('x'*80)],iface="enp134s0f0")
> +
> sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.1
> 68.0.4",dst="192.168.0.7",tos=4,ttl=20)/TCP(sport=25,dport=23)/Raw('x'*80)]
> ,iface="enp134s0f0")
> +
> + sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP()/UDP
> + ()/VXLAN()/Ether()/IP(src="192.168.0.4
> + ",dst="192.168.0.7")/UDP(sport=25,dport=23)/Raw('x'*80)],iface="enp134
> + s0f0")
> +
> +#. Check the packets are recieved in right queues by dut::
> +
> + testpmd> port 0/queue 1: received 1 packets
> + src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134
> - nb_segs=1 - RSS hash=0x96803f93 - RSS queue=0x1 - hw ptype: L2_ETHER
> L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP -
> l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + ......
> +
> +#. Create rules without priority, Check only patterns supported by switch
> can be created for the default priorty is 0.
> +So the first flow can be created and the second flow can not be created::
> +
> + testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.3 dst is
> 192.168.0.1 tos is 5 / tcp src is 25 dst is 23 / end actions queue index 1 / end
> + ice_flow_create(): Succeeded to create (2) flow
> + Flow rule #1 created
> + testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is
> 192.168.0.3 tos is 4 ttl is 20 / sctp src is 25 dst is 23 / end actions queue index
> 1 / end
> + ice_flow_create(): Failed to create flow
> + Caught error type 2 (flow rule (handle)): Invalid input pattern:
> + Invalid argument
> +
> +Test case: Create No Destination High Priority Flow Rule
> +========================================================
> +
> +A no destination high priority rule is not acceptable. Destination here means
> exact actions.
> +
> +Patterns in this case:
> + MAC_IPV4_TCP
> +
> +#. Start the ``testpmd`` application as follows::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w
> 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
> + set fwd rxonly
> + set verbose 1
> +
> +#. Create a rule without exact actions, check the flows can not be created::
> +
> + testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions /
> end
> + Bad arguments
> + testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end
> + Bad arguments
> +
> +Test case: Create Flow Rules Only Supported by Fdir Filter with
> +Priority 0
> +===============================================================
> ========
> +====
> +
> +Creating a rule only supported by fdir filter with priority 0, it is not
> acceptable.
> +
> +Patterns in this case:
> + MAC_IPV6_SCTP
> + MAC_IPV4_SCTP
> +
> +#. Start the ``testpmd`` application as follows::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w
> 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
> + set fwd rxonly
> + set verbose 1
> +
> +#. Create rules, check the flows can not be created::
> +
> + testpmd> flow create 0 priority 0 ingress pattern eth / ipv6 src is
> 1111:2222:3333:4444:5555:6666:7777:8888 dst is
> 1111:2222:3333:4444:5555:6666:7777:9999 / sctp src is 25 dst is 23 / end
> actions queue index 1 / end
> + ice_flow_create(): Failed to create flow
> + Caught error type 2 (flow rule (handle)): Invalid input pattern:
> + Invalid argument
> +
> + testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 ttl is 20 / sctp src is 25 dst is 23 / end
> actions queue index 1 / end
> + ice_flow_create(): Failed to create flow
> + Caught error type 2 (flow rule (handle)): Invalid input pattern:
> + Invalid argument
> +
> +
> +Test case: Create flow rules only supported by switch filter with
> +priority 1
> +===============================================================
> ========
> +======
> +
> +Create a rule only supported by fdir switch with priority 1, it is not
> acceptable.
> +
> +Patterns in this case:
> + MAC_IPV4_NVGRE_MAC_IPV4
> + MAC_IPV4_NVGRE_MAC_IPV4_UDP
> +
> +#. Start the ``testpmd`` application as follows::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w
> 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
> + set fwd rxonly
> + set verbose 1
> +
> +#. Create rules, check the flows can not be created::
> +
> + testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / nvgre / eth /
> ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 3 /
> end
> + ice_flow_create(): Failed to create flow
> + Caught error type 13 (specific pattern item): cause: 0x7fffe65b8128,
> + Unsupported pattern: Invalid argument
> +
> + testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / nvgre / eth /
> ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / udp src is 25 dst is 23 / end
> actions queue index 3 / end
> + ice_flow_create(): Failed to create flow
> + Caught error type 13 (specific pattern item): cause: 0x7fffe65b8128,
> + Unsupported pattern: Invalid argument
> +
> +Test case: Create flow rules with same parameter but differenet actions
> +===============================================================
> ========
> +===
> +
> +It is acceptable to create same rules with differenet filter in pipeline mode.
> +When fdir filter and switch filter has the same parameter rules, the flow will
> map to switch then fdir.
> +
> +Patterns in this case:
> + MAC_IPV4_TCP
> +
> +#. Start the ``testpmd`` application as follows::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w
> 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
> + set fwd rxonly
> + set verbose 1
> +
> +#. Create switch rule then fdir rule with the same parameter, check two
> flows can be created::
> +
> + testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions
> queue index 1 / end
> + ice_flow_create(): Succeeded to create (2) flow
> + Flow rule #0 created
> +
> + testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions
> queue index 3 / end
> + ice_interrupt_handler(): OICR: MDD event
> + ice_flow_create(): Succeeded to create (1) flow
> + Flow rule #1 created
> +
> +#. Tester send a pkt to dut::
> +
> +
> + sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="
> + 192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*8
> + 0)],iface="enp134s0f0")
> +
> +#. Check the packets are recieved by dut in queue 1::
> +
> + testpmd> port 0/queue 1: received 1 packets
> + src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134
> - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x1 - hw ptype: L2_ETHER
> L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP -
> l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> + PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> +
> +#. Remove the switch rule::
> +
> + testpmd>flow destroy 0 rule 0
> +
> +#. Tester send a pkt to dut::
> +
> +
> + sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="
> + 192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*8
> + 0)],iface="enp134s0f0")
> +
> +#. Check the packets are recieved in queue 3::
> +
> + testpmd> port 0/queue 3: received 1 packets
> + src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134
> - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x3 - hw ptype: L2_ETHER
> L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP -
> l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x3
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> + PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> +
> +#. Restart the ``testpmd`` application as follows::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 0000:af:00.0,
> pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
> + set fwd rxonly
> + set verbose 1
> +
> +#. Create fdir rule then switch rule with the same parameter, check two
> flows can be created::
> +
> + testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions
> queue index 3 / end
> + ice_interrupt_handler(): OICR: MDD event
> + ice_flow_create(): Succeeded to create (1) flow
> + Flow rule #0 created
> +
> + testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is
> 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions
> queue index 1 / end
> + ice_flow_create(): Succeeded to create (2) flow
> + Flow rule #1 created
> +
> +#. Tester send a pkt to dut::
> +
> +
> + sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="
> + 192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*8
> + 0)],iface="enp134s0f0")
> +
> +#. Check the packets are recieved by dut in queue 1::
> +
> + testpmd> port 0/queue 1: received 1 packets
> + src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134
> - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x1 - hw ptype: L2_ETHER
> L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP -
> l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> + PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> +
> +#. Remove the switch rule::
> +
> + testpmd>flow destroy 0 rule 1
> +
> +#. Tester send a pkt to dut::
> +
> +
> + sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="
> + 192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*8
> + 0)],iface="enp134s0f0")
> +
> +#. Check the packets are recieved in queue 3::
> +
> + testpmd> port 0/queue 3: received 1 packets
> + src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134
> - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x3 - hw ptype: L2_ETHER
> L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP -
> l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x3
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> + PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> --
> 2.17.1
^ permalink raw reply [flat|nested] 2+ messages in thread
* [dts] [PATCH V3]test_plans: add test plan for rte_flow priority
@ 2019-12-27 16:14 qifu
2019-12-27 8:08 ` Tu, Lijuan
0 siblings, 1 reply; 2+ messages in thread
From: qifu @ 2019-12-27 16:14 UTC (permalink / raw)
To: dts; +Cc: qifu
Add test plan for cvl rteflow priority.
Signed-off-by: qifu <qi.fu@intel.com>
---
test_plans/rteflow_priority_test_plan.rst | 338 ++++++++++++++++++++++
1 file changed, 338 insertions(+)
create mode 100644 test_plans/rteflow_priority_test_plan.rst
diff --git a/test_plans/rteflow_priority_test_plan.rst b/test_plans/rteflow_priority_test_plan.rst
new file mode 100644
index 0000000..b853e90
--- /dev/null
+++ b/test_plans/rteflow_priority_test_plan.rst
@@ -0,0 +1,338 @@
+.. Copyright (c) <2019>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+
+=======================
+Rte_flow Priority Tests
+=======================
+
+
+Description
+===========
+
+This document provides the plan for testing the Rte_flow Priority feature.
+this feature uses devargs as a hint to active flow priority or not.
+
+This test plan is based on Intel E810 series ethernet cards.
+when priority is not active, flows are created on fdir then switch/ACL.
+when priority is active, flows are identified into 2 category:
+High priority as permission stage that maps to switch/ACL,
+Low priority as distribution stage that maps to fdir,
+a no destination high priority rule is not acceptable, since it may be overwritten by a low priority rule due to cvl FXP behavior.
+
+Note: Since these tests are focus on priority, the patterns in tests are examples.
+
+
+Prerequisites
+=============
+
+Bind the pf to dpdk driver::
+
+ ./usertools/dpdk-devbind.py -b vfio-pci af:00.0
+
+Note: The kernel must be >= 3.6+ and VT-d must be enabled in bios.
+
+Test Case: Setting Priority in Non-pipeline Mode
+================================================
+
+Priority is not active in non-pipeline mode. The default value of priority is 0 but it will be ignored.
+
+Patterns in this case:
+ MAC_IPV4
+
+#. Start the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 0000:af:00.0 --log-level="ice,7" -- -i --txq=8 --rxq=8
+ set fwd rxonly
+ set verbose 1
+
+#. Create a rule with priority 0, Check the flow can be created but it will map to fdir filter::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / end
+ ice_interrupt_handler(): OICR: MDD event
+ ice_flow_create(): Succeeded to create (1) flow
+ Flow rule #0 created
+
+#. Create a rule with priority 1, check the flow can not be created for the vallue of priority is 0 in non-pipeline mode::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 4 (priority field): cause: 0x7ffe24e65738, Not support priority.: Invalid argument
+
+#. Start the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 0000:af:00.0,pipeline-mode-support=0 --log-level="ice,7" -- -i --txq=8 --rxq=8
+ set fwd rxonly
+ set verbose 1
+
+#. Create a rule with priority 0, Check the flow can be created but it will map to fdir filter::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / end
+ ice_interrupt_handler(): OICR: MDD event
+ ice_flow_create(): Succeeded to create (1) flow
+ Flow rule #0 created
+
+#. Create a rule with priority 1, check the flow can not be created for the vallue of priority is 0 in non-pipeline mode::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 2 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 4 (priority field): cause: 0x7ffe24e65738, Not support priority.: Invalid argument
+
+Test Case: Create Flow Rules with Priority in Pipeline Mode
+============================================================
+
+Priority is active in pipeline mode.
+Creating flow rules and setting priority 0/1 will map switch/fdir filter separately.
+
+Patterns in this case:
+ MAC_IPV4_TCP
+ MAC_IPV4_VXLAN_IPV4_UDP_PAY
+
+#. Start the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
+ set fwd rxonly
+ set verbose 1
+ rx_vxlan_port add 4789 0
+
+#. Create switch filter rules::
+
+ flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions queue index 1 / end
+
+ flow create 0 priority 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / udp src is 25 dst is 23 / end actions queue index 2 / end
+
+#. Create fdir filter rules::
+
+ flow create 0 priority 1 ingress pattern eth / ipv4 src is 192.168.0.4 dst is 192.168.0.7 tos is 4 ttl is 20 / tcp src is 25 dst is 23 / end actions queue index 3 / end
+
+ flow create 0 priority 1 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 src is 192.168.0.4 dst is 192.168.0.7 / udp src is 25 dst is 23 / end actions queue index 4 / end
+
+#. Check flow list with commands "flow list 0", all flows are created correctly::
+
+ +-----+--------+--------+--------+-----------------------+
+ |ID | Group | Prio | Attr | Rul |
+ +=====+========+========+========+=======================+
+ | 0 | 0 | 0 | i- | ETH IPV4 TCP => QUEUE |
+ +-----+--------+--------+--------+-----------------------+
+ | 1 ... |
+ +-----+--------+--------+--------+-----------------------+
+ | 2 ... |
+ +-----+--------+--------+--------+-----------------------+
+ | 3 ... |
+ +-----+--------+--------+--------+-----------------------+
+
+#. Send packets according to the created rules in tester::
+
+ sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
+ sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP()/UDP()/VXLAN()/Ether()/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/UDP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
+ sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.4",dst="192.168.0.7",tos=4,ttl=20)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
+ sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP()/UDP()/VXLAN()/Ether()/IP(src="192.168.0.4 ",dst="192.168.0.7")/UDP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
+
+#. Check the packets are recieved in right queues by dut::
+
+ testpmd> port 0/queue 1: received 1 packets
+ src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0x96803f93 - RSS queue=0x1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
+ ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
+ ......
+
+#. Create rules without priority, Check only patterns supported by switch can be created for the default priorty is 0.
+So the first flow can be created and the second flow can not be created::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.3 dst is 192.168.0.1 tos is 5 / tcp src is 25 dst is 23 / end actions queue index 1 / end
+ ice_flow_create(): Succeeded to create (2) flow
+ Flow rule #1 created
+ testpmd> flow create 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 ttl is 20 / sctp src is 25 dst is 23 / end actions queue index 1 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 2 (flow rule (handle)): Invalid input pattern: Invalid argument
+
+Test case: Create No Destination High Priority Flow Rule
+========================================================
+
+A no destination high priority rule is not acceptable. Destination here means exact actions.
+
+Patterns in this case:
+ MAC_IPV4_TCP
+
+#. Start the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
+ set fwd rxonly
+ set verbose 1
+
+#. Create a rule without exact actions, check the flows can not be created::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions / end
+ Bad arguments
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end
+ Bad arguments
+
+Test case: Create Flow Rules Only Supported by Fdir Filter with Priority 0
+===========================================================================
+
+Creating a rule only supported by fdir filter with priority 0, it is not acceptable.
+
+Patterns in this case:
+ MAC_IPV6_SCTP
+ MAC_IPV4_SCTP
+
+#. Start the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
+ set fwd rxonly
+ set verbose 1
+
+#. Create rules, check the flows can not be created::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv6 src is 1111:2222:3333:4444:5555:6666:7777:8888 dst is 1111:2222:3333:4444:5555:6666:7777:9999 / sctp src is 25 dst is 23 / end actions queue index 1 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 2 (flow rule (handle)): Invalid input pattern: Invalid argument
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 ttl is 20 / sctp src is 25 dst is 23 / end actions queue index 1 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 2 (flow rule (handle)): Invalid input pattern: Invalid argument
+
+
+Test case: Create flow rules only supported by switch filter with priority 1
+=============================================================================
+
+Create a rule only supported by fdir switch with priority 1, it is not acceptable.
+
+Patterns in this case:
+ MAC_IPV4_NVGRE_MAC_IPV4
+ MAC_IPV4_NVGRE_MAC_IPV4_UDP
+
+#. Start the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
+ set fwd rxonly
+ set verbose 1
+
+#. Create rules, check the flows can not be created::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / nvgre / eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / end actions queue index 3 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 13 (specific pattern item): cause: 0x7fffe65b8128, Unsupported pattern: Invalid argument
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 / nvgre / eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / udp src is 25 dst is 23 / end actions queue index 3 / end
+ ice_flow_create(): Failed to create flow
+ Caught error type 13 (specific pattern item): cause: 0x7fffe65b8128, Unsupported pattern: Invalid argument
+
+Test case: Create flow rules with same parameter but differenet actions
+==========================================================================
+
+It is acceptable to create same rules with differenet filter in pipeline mode.
+When fdir filter and switch filter has the same parameter rules, the flow will map to switch then fdir.
+
+Patterns in this case:
+ MAC_IPV4_TCP
+
+#. Start the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 0000:af:00.0,pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
+ set fwd rxonly
+ set verbose 1
+
+#. Create switch rule then fdir rule with the same parameter, check two flows can be created::
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions queue index 1 / end
+ ice_flow_create(): Succeeded to create (2) flow
+ Flow rule #0 created
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions queue index 3 / end
+ ice_interrupt_handler(): OICR: MDD event
+ ice_flow_create(): Succeeded to create (1) flow
+ Flow rule #1 created
+
+#. Tester send a pkt to dut::
+
+ sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
+
+#. Check the packets are recieved by dut in queue 1::
+
+ testpmd> port 0/queue 1: received 1 packets
+ src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
+ ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
+
+#. Remove the switch rule::
+
+ testpmd>flow destroy 0 rule 0
+
+#. Tester send a pkt to dut::
+
+ sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
+
+#. Check the packets are recieved in queue 3::
+
+ testpmd> port 0/queue 3: received 1 packets
+ src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x3 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x3
+ ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
+
+#. Restart the ``testpmd`` application as follows::
+
+ ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 0000:af:00.0, pipeline-mode-support=1 --log-level="ice,7" -- -i --txq=8 --rxq=8
+ set fwd rxonly
+ set verbose 1
+
+#. Create fdir rule then switch rule with the same parameter, check two flows can be created::
+
+ testpmd> flow create 0 priority 1 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions queue index 3 / end
+ ice_interrupt_handler(): OICR: MDD event
+ ice_flow_create(): Succeeded to create (1) flow
+ Flow rule #0 created
+
+ testpmd> flow create 0 priority 0 ingress pattern eth / ipv4 src is 192.168.0.2 dst is 192.168.0.3 tos is 4 / tcp src is 25 dst is 23 / end actions queue index 1 / end
+ ice_flow_create(): Succeeded to create (2) flow
+ Flow rule #1 created
+
+#. Tester send a pkt to dut::
+
+ sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
+
+#. Check the packets are recieved by dut in queue 1::
+
+ testpmd> port 0/queue 1: received 1 packets
+ src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x1 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x1
+ ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
+
+#. Remove the switch rule::
+
+ testpmd>flow destroy 0 rule 1
+
+#. Tester send a pkt to dut::
+
+ sendp([Ether(dst="00:00:00:00:11:00",src="11:22:33:44:55:66")/IP(src="192.168.0.2",dst="192.168.0.3",tos=4)/TCP(sport=25,dport=23)/Raw('x'*80)],iface="enp134s0f0")
+
+#. Check the packets are recieved in queue 3::
+
+ testpmd> port 0/queue 3: received 1 packets
+ src=11:22:33:44:55:66 - dst=00:00:00:00:11:00 - type=0x0800 - length=134 - nb_segs=1 - RSS hash=0xf12811f1 - RSS queue=0x3 - hw ptype: L2_ETHER L3_IPV4_EXT_UNKNOWN L4_TCP - sw ptype: L2_ETHER L3_IPV4 L4_TCP - l2_len=14 - l3_len=20 - l4_len=20 - Receive queue=0x3
+ ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
--
2.17.1
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2019-12-27 8:08 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-27 16:14 [dts] [PATCH V3]test_plans: add test plan for rte_flow priority qifu
2019-12-27 8:08 ` Tu, Lijuan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).