* [dts] [PATCH] L2TPv3 Test plan document
@ 2020-02-17 9:05 Varalakshmi
2020-02-24 5:16 ` Peng, Yuan
2020-02-25 1:22 ` Tu, Lijuan
0 siblings, 2 replies; 4+ messages in thread
From: Varalakshmi @ 2020-02-17 9:05 UTC (permalink / raw)
To: dts; +Cc: Varalakshmi
L2TPv3 Test plan document contains:
1. Prerequisites
2. Test scenarios
Signed-off-by: Varalakshmi <varalakshmi.s@intel.com>
---
test_plans/ddp_l2tpv3_test_plan.rst | 900 ++++++++++++++++++++++++++++
1 file changed, 900 insertions(+)
create mode 100644 test_plans/ddp_l2tpv3_test_plan.rst
diff --git a/test_plans/ddp_l2tpv3_test_plan.rst b/test_plans/ddp_l2tpv3_test_plan.rst
new file mode 100644
index 0000000..77f03a9
--- /dev/null
+++ b/test_plans/ddp_l2tpv3_test_plan.rst
@@ -0,0 +1,900 @@
+.. Copyright (c) <2018>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+==========
+DDP L2TPV3
+==========
+
+DDP profile 0x80000004 adds support for directing L2TPv3 packets based on
+their session ID for FVL NIC. For DDP introduction, please refer to :
+
+ https://software.intel.com/en-us/articles/dynamic-device-personalization-for-intel-ethernet-700-series
+
+l2tpv3oip-l4.pkg defines and supports below pctype packets, also
+could check the information using command “ddp get info <profile>”
+after loading the profile. left numbers are pctype values,right are
+supported packets::
+
+ 28: IPV4 L2TPV3
+ 38: IPV6 L2TPV3
+
+Packet Classifier types and Its Input Set
+
+ +--------------+--------+-----------------------+-------------------------+
+ | Packet Type | PCType | Hash Input Set | FD Input Set |
+ +--------------+--------+-----------------------+-------------------------+
+ | IPv4,L2TPv3 | 28 | L2TPv3 Session ID | L2TPv3 Session ID |
+ +--------------+--------+-----------------------+-------------------------+
+ | IPv6,L2TPv3 | 38 | L2TPv3 Session ID | L2TPv3 Session ID |
+ +--------------+--------+-----------------------+-------------------------+
+
+
+Requirements as below
+=====================
+
+Flow API support for flow director rules based on L2TPv3 session ID
+The current scope is limited to FVL NIC
+
+Prerequisites
+=============
+
+1. DPDK version 20.02 or greater
+
+2. I40E NIC with FW version 6.0 or greater
+
+ In your linux terminal enter ethtool -i <interface-name> , this prints out
+ the driver details.
+ Ex ::
+
+ root@hostname:~/dpdk# ethtool -i <interface-name>
+ driver: i40e
+ version: 2.1.14-k
+ firmware-version: 7.10 0x80006474 1.2527.0
+ expansion-rom-version:
+ bus-info: 0000:02:00.1
+ supports-statistics: yes
+ supports-test: yes
+ supports-eeprom-access: yes
+ supports-register-dump: yes
+ supports-priv-flags: yes
+
+*Note: If the firmware version is below 6.0 , the NIC does not support
+any DDP functionality*
+
+3. Download and extract L2TPv3 package
+
+ https://downloadcenter.intel.com/download/28941/Dynamic-Device-Personalization-L2TPv3
+
+4. Bind the Port to the userspace Driver <igb_uio/vfio-pci)::
+
+ ./usertools/dpdk-devbind.py -b <igb_uio/vfio-pci> <PCI address of device to bind>
+
+5. Start the TESTPMD::
+
+ ./x86_64-native-linuxapp-gcc/build/app/test-pmd/testpmd -c f -n 4 -w
+ <PCI address of device> -- -i --port-topology=chained --txq=64 --rxq=64
+ --pkt-filter-mode=perfect
+
+ For testpmd commands refer: https://doc.dpdk.org/guides/testpmd_app_ug/
+
+6. Set Verbose
+
+ To enable verbose logging in the testpmd application to get detailed
+ information about rx queues and packet metadata::
+
+ testpmd > set verbose 1
+
+7. To enable required fields as per the indices in the L2TPv3 Packet field
+ vector (refer Dynamic_Device_Personalization_L2TPv3_Rev1.x)
+
+ To enable the specific field in the vector for a PCTYPE , the following
+ command may be used::
+
+ testpmd> port config <port_id> pctype <PCTYPE> fdir_inset set field
+ <field_index>
+
+ To check if a specific field in the vector is set for a PCTYPE, the
+ following command may be used::
+
+ testpmd> port config <port_id> pctype <PCTYPE> fdir_inset get field
+ <field_index>
+
+ To clear any specific field in the vector for a PCTYPE, the following
+ command may be used::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear field
+ <field_index>
+
+ To clear all fields for a specific PCTYPE, the following commands may
+ be used::
+
+ testpmd> port config <port_id> pctype <PCTYPE> fdir_inset clear all
+
+*NOTE: Changes such as enabling/disabling of specific field in the vector
+for a PCTYPE will remain applied across restarts of testpmd application.
+It is good practice to explicitly set the desired field in the vector for
+a PCTYPE upon start of testpmd.*
+
+
+Test Case : Adding L2TPv3 profile to the port
+=============================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Load l2tpv3oip-l4.pkg file to the memory buffer and save the existing
+ configuration to the l2tpv3oip-l4.bak file::
+
+ testpmd > ddp add <port_id> <path>/l2tpv3oip-l4.pkg,<path>/
+ l2tpv3oip-l4.bak
+
+3. Check to see if the profile is loaded ::
+
+ testpmd> ddp get list <port_id>
+ Track id: 0x80000004
+ Version: 1.0.0.0
+ Profile name: L2TPv3oIP with L4 payload
+
+Test Case : Deleting L2TPv3 profile from the port
+=================================================
+
+This test is intended to revert to the original DDP profile of the port
+without reset
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Remove profile from the network adapter and restore original
+ configuration::
+
+ testpmd > ddp del <port_id> <path>/l2tpv3oip-l4.bak
+
+3. Check to see if the profile is deleted::
+
+ testpmd> ddp get list <port_id>
+ Profile number is: 0
+
+Test Case : Adding and deleting Flow Director rules
+===================================================
+
+1. To Add l2tpv3 flow director rules::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1 / end actions queue index 1 / end
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 2 / end actions queue index 2 / end
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 3 / end actions queue index 3 / end
+
+2. To List the rules using the flow list command with port number::
+
+ testpmd> flow list <port_id>
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ 1 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ 2 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+
+3. To delete a single rule ::
+
+ testpmd> flow destroy <port_id> rule 0
+ Flow rule #0 destroyed
+ testpmd> flow list <port_id>
+ ID Group Prio Attr Rule
+ 1 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ 2 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ <flow rule with ID 0 should not be listed>
+
+4. To delete all the rules::
+
+ testpmd> flow flush <port_id>
+ testpmd> flow list <port_id>
+ testpmd>
+ (No List is printed)
+
+Test Case: L2TPv3 over IPv4 packet
+==================================
+
+1. Add l2tpv3 flow director rule, set sessionID as 1, queue 1::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1 / end actions queue index 1 / end
+
+2. Send L2TPv3 packet with session ID matching the configured rule, Packets
+ should be received on queue 1::
+
+ p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+3. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x11')/Raw('x' * 20)
+
+Test Case: L2TPv3 over IPv6 packet
+==================================
+
+1. Add l2tpv3 flow director rule, set sessionID as 1000, queue 2::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip session_id
+ is 1000 / end actions queue index 2 / end
+
+2. Send L2TPv3 packet with session ID matching the configured rule, Packets
+ should be received on queue 2::
+
+ p=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+3. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\x88')/Raw('x' * 20)
+
+Test Case: L2TPv3oIPv4 with L2TPv3oIPv6 configuration
+========================================================
+
+1. Add l2tpv3 flow director rules , set sessionID as 1001, queue 1 for IPv4
+ and IPv6 flows::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1001 / end actions queue index 1 / end
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip session_id
+ is 1001 / end actions queue index 1 / end
+
+2. Send L2TPv3 packets for IPv4 and IPv6 with session ID same as configured
+ rule, Packets should be received on queue 1::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+
+3. Send L2TPv3 packets(IPv4 and IPv6) with session ID not matching the
+ configured rules, Packet should be received on queue 0::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xf9')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xf9')/Raw('x' * 20)
+
+Test Case: UDP, L2TPv3oIPv4 with L2TPv3oIPv6 configurations
+============================================================
+
+1. Add l2tpv3 flow director rules , set sessionID as 1001, queue 1 for IPv4
+ and queue 2 for IPv6 flows::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1001 / end actions queue index 1 / end
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip session_id
+ is 1001 / end actions queue index 2 / end
+
+2. Add UDP flow director rule , set queue 3 for UDP packets::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / udp / end actions
+ queue index 3 / end
+
+3. Send L2TPv3 packets for IPv4 and IPv6 with session ID same as configured
+ rules, Packets should be received on queue 1 and queue 2 respectively::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+4. Send L2TPv3 packets(IPv4 and IPv6) with session ID not matching the
+ configured rules, Packet should be received on queue 0::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\x09')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\x09')/Raw('x' * 20)
+
+5. Send IPv4/UDP packet. Verify that the packet is received on queue 3::
+
+ P_UDP=Ether()/IP()/UDP()
+
+Test Case: L2TPv3oIPv4 configuration with specific SIP and DIP
+==============================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1 queue 1::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 dst
+ is 20.10.10.20 / l2tpv3oip session_id is 1 / end actions queue index 10
+ / end
+
+6. Send L2TPv3 packet with SIP,DIP and session ID matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",dst="20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether(src="00:00:00:00:00:02", dst="3C:FD:FE:A5:49:88")/IP(proto=115)
+ /Raw('\x00\x00\x00\x44')/Raw('x' * 20)
+
+8. Send L2TPv3 packet with SIP not matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="100.10.10.1",dst="20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+9. Send L2TPv3 packet with DIP not matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",dst="200.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+Test Case: L2TPv3oIPv6 configuration with specific SIP and DIP
+==============================================================
+
+1. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1000 queue 20::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ dst is 8:7:6:5:4:3:2:1 / l2tpv3oip session_id is 1000 / end actions queue
+ index 20 / end
+
+6. Send L2TPv3 packet with session ID, SIP and DIP matching the configured
+ rule, Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xff')/Raw('x' * 20)
+
+8. Send L2TPv3 packet with Source IP not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+9. Send L2TPv3 packet with Destination IP not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1111",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+Test Case: L2TPv3oIPv4 configuration with specific SIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop all
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1, queue 10::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 /
+ l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Send L2TPv3 packet with SIP and session ID matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+
+ p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x21')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with SIP not matching the configured rule, Packets
+ should be received on queue 0::
+
+ p=Ether()/IP(src="20.20.20.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3oIPv6 configuration with specific SIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+6. Send L2TPv3 packet with SIP and session ID matching the configured rule,
+ Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xff')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with SIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3oIPv4 configuration with specific DIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1, queue 10::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 dst is 20.10.10.20
+ / l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Send L2TPv3 packet with DIP and session ID matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x44')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IP(dst="2220.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3oIPv6 configuration with specific DIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 dst is 8:7:6:5:4:3:2:1
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+6. Send L2TPv3 packet with session ID, DIP matching the configured rule,
+ Packets should be received on queue 20::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xff')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8888:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3 with specific IPv4 SIP and IPv6 SIP configured together
+=========================================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule,set sessionID as 1,queue 10 for IPv4 flow::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 /
+ l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Add l2tpv3 flow director rule,set sessionID as 1000,
+ queue 20 for IPv6 flow::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+7. Send L2TPv3 IPv4 packet with SIP and session ID matching the configured
+ rule, Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x44')/Raw('x' * 20)
+
+9. Send L2TPv3 IPv4 packet with SIP not matching the configured rule,
+ Packets should be received on queue 0::
+
+ p=Ether()/IP(src="20.20.20.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+10. Send L2TPv3 IPv6 packet with SIP and session ID matching the configured
+ rule, Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+11. Send L2TPv3 IPv6 packet with session ID not matching the configured
+ rule, Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xff')
+ /Raw('x' * 20)
+
+12. Send L2TPv3 IPv6 packet with SIP not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')
+ /Raw('x' * 20)
+
+Test Case: L2TPv3 with specific IPv4 DIP and IPv6 DIP configured together
+=========================================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1 queue 10 for IPv4::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 dst is 20.10.10.20 /
+ l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20 for IPv6::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 dst is 8:7:6:5:4:3:2:1
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+7. Send L2TPv3 IPv4 packet with DIP and session ID matching the configured
+ rule,Packets should be received on queue 10::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x21')/
+ Raw('x' * 20)
+
+9. Send L2TPv3 IPv4 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IP(dst="2220.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+10. Send L2TPv3 packet with session ID, DIP matching the configured rule,
+ Packets should be received on queue 20::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+11. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xff')/
+ Raw('x' * 20)
+
+12. Send L2TPv3 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8888:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3 with IPv4 SIP, DIP and IPv6 SIP, DIP configured together
+==========================================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule,set sessionID as 1,queue 10 for IPv4 flow::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 dst
+ is 20.10.10.20 / l2tpv3oip session_id is 1 / end actions queue index 10
+ / end
+
+6. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20 for IPv6
+ flow ::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ ipv6 dst is 8:7:6:5:4:3:2:1 / l2tpv3oip session_id is 1000 / end actions
+ queue index 20 / end
+
+7. Send L2TPv3 IPv4 packet with SIP, DIP and session ID matching the
+ configured rule, Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1", dst= "20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(src="10.10.10.1", dst= "20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x11')/Raw('x' * 20)
+
+9. Send L2TPv3 IPv4 packet with SIP not matching the configured rule,
+ Packets should be received on queue 0::
+
+ p=Ether()/IP(src="100.10.10.1", dst= "20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+10. Send L2TPv3 IPv4 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IP(src="10.10.10.1", dst="220.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+11. Send L2TPv3 IPv6 packet with SIP, DIP and session ID matching the
+ configured rule, Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+12. Send L2TPv3 IPv6 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xF8')/Raw('x' * 20)
+
+13. Send L2TPv3 IPv6 packet with SIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)
+ /Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+14. Send L2TPv3 IPv6 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8888:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
--
2.17.1
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [dts] [PATCH] L2TPv3 Test plan document
2020-02-17 9:05 [dts] [PATCH] L2TPv3 Test plan document Varalakshmi
@ 2020-02-24 5:16 ` Peng, Yuan
2020-02-25 1:22 ` Tu, Lijuan
1 sibling, 0 replies; 4+ messages in thread
From: Peng, Yuan @ 2020-02-24 5:16 UTC (permalink / raw)
To: S, Varalakshmi, dts; +Cc: S, Varalakshmi
Acked by Peng, Yuan <yuan.peng@intel.com>
-----Original Message-----
From: dts <dts-bounces@dpdk.org> On Behalf Of Varalakshmi
Sent: Monday, February 17, 2020 5:05 PM
To: dts@dpdk.org
Cc: S, Varalakshmi <varalakshmi.s@intel.com>
Subject: [dts] [PATCH] L2TPv3 Test plan document
L2TPv3 Test plan document contains:
1. Prerequisites
2. Test scenarios
Signed-off-by: Varalakshmi <varalakshmi.s@intel.com>
---
test_plans/ddp_l2tpv3_test_plan.rst | 900 ++++++++++++++++++++++++++++
1 file changed, 900 insertions(+)
create mode 100644 test_plans/ddp_l2tpv3_test_plan.rst
diff --git a/test_plans/ddp_l2tpv3_test_plan.rst b/test_plans/ddp_l2tpv3_test_plan.rst
new file mode 100644
index 0000000..77f03a9
--- /dev/null
+++ b/test_plans/ddp_l2tpv3_test_plan.rst
@@ -0,0 +1,900 @@
+.. Copyright (c) <2018>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+==========
+DDP L2TPV3
+==========
+
+DDP profile 0x80000004 adds support for directing L2TPv3 packets based
+on their session ID for FVL NIC. For DDP introduction, please refer to :
+
+ https://software.intel.com/en-us/articles/dynamic-device-personalizati
+ on-for-intel-ethernet-700-series
+
+l2tpv3oip-l4.pkg defines and supports below pctype packets, also could
+check the information using command “ddp get info <profile>”
+after loading the profile. left numbers are pctype values,right are
+supported packets::
+
+ 28: IPV4 L2TPV3
+ 38: IPV6 L2TPV3
+
+Packet Classifier types and Its Input Set
+
+ +--------------+--------+-----------------------+-------------------------+
+ | Packet Type | PCType | Hash Input Set | FD Input Set |
+ +--------------+--------+-----------------------+-------------------------+
+ | IPv4,L2TPv3 | 28 | L2TPv3 Session ID | L2TPv3 Session ID |
+ +--------------+--------+-----------------------+-------------------------+
+ | IPv6,L2TPv3 | 38 | L2TPv3 Session ID | L2TPv3 Session ID |
+
+ +--------------+--------+-----------------------+---------------------
+ ----+
+
+
+Requirements as below
+=====================
+
+Flow API support for flow director rules based on L2TPv3 session ID The
+current scope is limited to FVL NIC
+
+Prerequisites
+=============
+
+1. DPDK version 20.02 or greater
+
+2. I40E NIC with FW version 6.0 or greater
+
+ In your linux terminal enter ethtool -i <interface-name> , this prints out
+ the driver details.
+ Ex ::
+
+ root@hostname:~/dpdk# ethtool -i <interface-name>
+ driver: i40e
+ version: 2.1.14-k
+ firmware-version: 7.10 0x80006474 1.2527.0
+ expansion-rom-version:
+ bus-info: 0000:02:00.1
+ supports-statistics: yes
+ supports-test: yes
+ supports-eeprom-access: yes
+ supports-register-dump: yes
+ supports-priv-flags: yes
+
+*Note: If the firmware version is below 6.0 , the NIC does not support
+any DDP functionality*
+
+3. Download and extract L2TPv3 package
+
+
+ https://downloadcenter.intel.com/download/28941/Dynamic-Device-Persona
+ lization-L2TPv3
+
+4. Bind the Port to the userspace Driver <igb_uio/vfio-pci)::
+
+ ./usertools/dpdk-devbind.py -b <igb_uio/vfio-pci> <PCI address of
+ device to bind>
+
+5. Start the TESTPMD::
+
+ ./x86_64-native-linuxapp-gcc/build/app/test-pmd/testpmd -c f -n 4 -w
+ <PCI address of device> -- -i --port-topology=chained --txq=64 --rxq=64
+ --pkt-filter-mode=perfect
+
+ For testpmd commands refer:
+ https://doc.dpdk.org/guides/testpmd_app_ug/
+
+6. Set Verbose
+
+ To enable verbose logging in the testpmd application to get detailed
+ information about rx queues and packet metadata::
+
+ testpmd > set verbose 1
+
+7. To enable required fields as per the indices in the L2TPv3 Packet field
+ vector (refer Dynamic_Device_Personalization_L2TPv3_Rev1.x)
+
+ To enable the specific field in the vector for a PCTYPE , the following
+ command may be used::
+
+ testpmd> port config <port_id> pctype <PCTYPE> fdir_inset set field
+ <field_index>
+
+ To check if a specific field in the vector is set for a PCTYPE, the
+ following command may be used::
+
+ testpmd> port config <port_id> pctype <PCTYPE> fdir_inset get field
+ <field_index>
+
+ To clear any specific field in the vector for a PCTYPE, the following
+ command may be used::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear field
+ <field_index>
+
+ To clear all fields for a specific PCTYPE, the following commands may
+ be used::
+
+ testpmd> port config <port_id> pctype <PCTYPE> fdir_inset clear all
+
+*NOTE: Changes such as enabling/disabling of specific field in the
+vector for a PCTYPE will remain applied across restarts of testpmd application.
+It is good practice to explicitly set the desired field in the vector
+for a PCTYPE upon start of testpmd.*
+
+
+Test Case : Adding L2TPv3 profile to the port
+=============================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Load l2tpv3oip-l4.pkg file to the memory buffer and save the existing
+ configuration to the l2tpv3oip-l4.bak file::
+
+ testpmd > ddp add <port_id> <path>/l2tpv3oip-l4.pkg,<path>/
+ l2tpv3oip-l4.bak
+
+3. Check to see if the profile is loaded ::
+
+ testpmd> ddp get list <port_id>
+ Track id: 0x80000004
+ Version: 1.0.0.0
+ Profile name: L2TPv3oIP with L4 payload
+
+Test Case : Deleting L2TPv3 profile from the port
+=================================================
+
+This test is intended to revert to the original DDP profile of the port
+without reset
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Remove profile from the network adapter and restore original
+ configuration::
+
+ testpmd > ddp del <port_id> <path>/l2tpv3oip-l4.bak
+
+3. Check to see if the profile is deleted::
+
+ testpmd> ddp get list <port_id>
+ Profile number is: 0
+
+Test Case : Adding and deleting Flow Director rules
+===================================================
+
+1. To Add l2tpv3 flow director rules::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1 / end actions queue index 1 / end
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 2 / end actions queue index 2 / end
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 3 / end actions queue index 3 / end
+
+2. To List the rules using the flow list command with port number::
+
+ testpmd> flow list <port_id>
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ 1 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ 2 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+
+3. To delete a single rule ::
+
+ testpmd> flow destroy <port_id> rule 0
+ Flow rule #0 destroyed
+ testpmd> flow list <port_id>
+ ID Group Prio Attr Rule
+ 1 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ 2 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ <flow rule with ID 0 should not be listed>
+
+4. To delete all the rules::
+
+ testpmd> flow flush <port_id>
+ testpmd> flow list <port_id>
+ testpmd>
+ (No List is printed)
+
+Test Case: L2TPv3 over IPv4 packet
+==================================
+
+1. Add l2tpv3 flow director rule, set sessionID as 1, queue 1::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1 / end actions queue index 1 / end
+
+2. Send L2TPv3 packet with session ID matching the configured rule, Packets
+ should be received on queue 1::
+
+ p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+3. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x11')/Raw('x' * 20)
+
+Test Case: L2TPv3 over IPv6 packet
+==================================
+
+1. Add l2tpv3 flow director rule, set sessionID as 1000, queue 2::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip session_id
+ is 1000 / end actions queue index 2 / end
+
+2. Send L2TPv3 packet with session ID matching the configured rule, Packets
+ should be received on queue 2::
+
+ p=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+3. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\x88')/Raw('x' * 20)
+
+Test Case: L2TPv3oIPv4 with L2TPv3oIPv6 configuration
+========================================================
+
+1. Add l2tpv3 flow director rules , set sessionID as 1001, queue 1 for IPv4
+ and IPv6 flows::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1001 / end actions queue index 1 / end
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip session_id
+ is 1001 / end actions queue index 1 / end
+
+2. Send L2TPv3 packets for IPv4 and IPv6 with session ID same as configured
+ rule, Packets should be received on queue 1::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+
+3. Send L2TPv3 packets(IPv4 and IPv6) with session ID not matching the
+ configured rules, Packet should be received on queue 0::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xf9')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xf9')/Raw('x' * 20)
+
+Test Case: UDP, L2TPv3oIPv4 with L2TPv3oIPv6 configurations
+============================================================
+
+1. Add l2tpv3 flow director rules , set sessionID as 1001, queue 1 for IPv4
+ and queue 2 for IPv6 flows::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1001 / end actions queue index 1 / end
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip session_id
+ is 1001 / end actions queue index 2 / end
+
+2. Add UDP flow director rule , set queue 3 for UDP packets::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / udp / end actions
+ queue index 3 / end
+
+3. Send L2TPv3 packets for IPv4 and IPv6 with session ID same as configured
+ rules, Packets should be received on queue 1 and queue 2 respectively::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+4. Send L2TPv3 packets(IPv4 and IPv6) with session ID not matching the
+ configured rules, Packet should be received on queue 0::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\x09')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\x09')/Raw('x' * 20)
+
+5. Send IPv4/UDP packet. Verify that the packet is received on queue 3::
+
+ P_UDP=Ether()/IP()/UDP()
+
+Test Case: L2TPv3oIPv4 configuration with specific SIP and DIP
+==============================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field
+ 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1 queue 1::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 dst
+ is 20.10.10.20 / l2tpv3oip session_id is 1 / end actions queue index 10
+ / end
+
+6. Send L2TPv3 packet with SIP,DIP and session ID matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",dst="20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether(src="00:00:00:00:00:02", dst="3C:FD:FE:A5:49:88")/IP(proto=115)
+ /Raw('\x00\x00\x00\x44')/Raw('x' * 20)
+
+8. Send L2TPv3 packet with SIP not matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="100.10.10.1",dst="20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+9. Send L2TPv3 packet with DIP not matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",dst="200.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+Test Case: L2TPv3oIPv6 configuration with specific SIP and DIP
+==============================================================
+
+1. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field
+ 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1000 queue 20::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ dst is 8:7:6:5:4:3:2:1 / l2tpv3oip session_id is 1000 / end actions queue
+ index 20 / end
+
+6. Send L2TPv3 packet with session ID, SIP and DIP matching the configured
+ rule, Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xff')/Raw('x' * 20)
+
+8. Send L2TPv3 packet with Source IP not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+9. Send L2TPv3 packet with Destination IP not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1111",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+Test Case: L2TPv3oIPv4 configuration with specific SIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop all
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field
+ 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1, queue 10::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 /
+ l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Send L2TPv3 packet with SIP and session ID matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+
+ p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x21')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with SIP not matching the configured rule, Packets
+ should be received on queue 0::
+
+ p=Ether()/IP(src="20.20.20.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3oIPv6 configuration with specific SIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field
+ 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+6. Send L2TPv3 packet with SIP and session ID matching the configured rule,
+ Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xff')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with SIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3oIPv4 configuration with specific DIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field
+ 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1, queue 10::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 dst is 20.10.10.20
+ / l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Send L2TPv3 packet with DIP and session ID matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x44')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IP(dst="2220.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3oIPv6 configuration with specific DIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field
+ 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 dst is 8:7:6:5:4:3:2:1
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+6. Send L2TPv3 packet with session ID, DIP matching the configured rule,
+ Packets should be received on queue 20::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xff')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8888:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3 with specific IPv4 SIP and IPv6 SIP configured
+together
+=======================================================================
+==
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field
+ 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule,set sessionID as 1,queue 10 for IPv4 flow::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 /
+ l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Add l2tpv3 flow director rule,set sessionID as 1000,
+ queue 20 for IPv6 flow::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+7. Send L2TPv3 IPv4 packet with SIP and session ID matching the configured
+ rule, Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x44')/Raw('x' * 20)
+
+9. Send L2TPv3 IPv4 packet with SIP not matching the configured rule,
+ Packets should be received on queue 0::
+
+ p=Ether()/IP(src="20.20.20.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+10. Send L2TPv3 IPv6 packet with SIP and session ID matching the configured
+ rule, Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+11. Send L2TPv3 IPv6 packet with session ID not matching the configured
+ rule, Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xff')
+ /Raw('x' * 20)
+
+12. Send L2TPv3 IPv6 packet with SIP not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')
+ /Raw('x' * 20)
+
+Test Case: L2TPv3 with specific IPv4 DIP and IPv6 DIP configured
+together
+=======================================================================
+==
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field
+ 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1 queue 10 for IPv4::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 dst is 20.10.10.20 /
+ l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20 for IPv6::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 dst is 8:7:6:5:4:3:2:1
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+7. Send L2TPv3 IPv4 packet with DIP and session ID matching the configured
+ rule,Packets should be received on queue 10::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x21')/
+ Raw('x' * 20)
+
+9. Send L2TPv3 IPv4 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+
+ p=Ether()/IP(dst="2220.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/Ra
+ w('x' * 20)
+
+10. Send L2TPv3 packet with session ID, DIP matching the configured rule,
+ Packets should be received on queue 20::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+11. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xff')/
+ Raw('x' * 20)
+
+12. Send L2TPv3 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8888:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3 with IPv4 SIP, DIP and IPv6 SIP, DIP configured
+together
+=======================================================================
+===
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field
+ 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule,set sessionID as 1,queue 10 for IPv4 flow::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 dst
+ is 20.10.10.20 / l2tpv3oip session_id is 1 / end actions queue index 10
+ / end
+
+6. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20 for IPv6
+ flow ::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ ipv6 dst is 8:7:6:5:4:3:2:1 / l2tpv3oip session_id is 1000 / end actions
+ queue index 20 / end
+
+7. Send L2TPv3 IPv4 packet with SIP, DIP and session ID matching the
+ configured rule, Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1", dst= "20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(src="10.10.10.1", dst= "20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x11')/Raw('x' * 20)
+
+9. Send L2TPv3 IPv4 packet with SIP not matching the configured rule,
+ Packets should be received on queue 0::
+
+ p=Ether()/IP(src="100.10.10.1", dst= "20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+10. Send L2TPv3 IPv4 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IP(src="10.10.10.1", dst="220.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+11. Send L2TPv3 IPv6 packet with SIP, DIP and session ID matching the
+ configured rule, Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+12. Send L2TPv3 IPv6 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xF8')/Raw('x' * 20)
+
+13. Send L2TPv3 IPv6 packet with SIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)
+ /Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+14. Send L2TPv3 IPv6 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8888:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
--
2.17.1
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [dts] [PATCH] L2TPv3 Test plan document
2020-02-17 9:05 [dts] [PATCH] L2TPv3 Test plan document Varalakshmi
2020-02-24 5:16 ` Peng, Yuan
@ 2020-02-25 1:22 ` Tu, Lijuan
1 sibling, 0 replies; 4+ messages in thread
From: Tu, Lijuan @ 2020-02-25 1:22 UTC (permalink / raw)
To: S, Varalakshmi, dts; +Cc: S, Varalakshmi
Applied， thanks
> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of Varalakshmi
> Sent: Monday, February 17, 2020 5:05 PM
> To: dts@dpdk.org
> Cc: S, Varalakshmi <varalakshmi.s@intel.com>
> Subject: [dts] [PATCH] L2TPv3 Test plan document
>
> L2TPv3 Test plan document contains:
> 1. Prerequisites
> 2. Test scenarios
>
>
> Signed-off-by: Varalakshmi <varalakshmi.s@intel.com>
> ---
> test_plans/ddp_l2tpv3_test_plan.rst | 900 ++++++++++++++++++++++++++++
> 1 file changed, 900 insertions(+)
> create mode 100644 test_plans/ddp_l2tpv3_test_plan.rst
>
> diff --git a/test_plans/ddp_l2tpv3_test_plan.rst
> b/test_plans/ddp_l2tpv3_test_plan.rst
> new file mode 100644
> index 0000000..77f03a9
> --- /dev/null
> +++ b/test_plans/ddp_l2tpv3_test_plan.rst
> @@ -0,0 +1,900 @@
> +.. Copyright (c) <2018>, Intel Corporation
> + All rights reserved.
> +
> + Redistribution and use in source and binary forms, with or without
> + modification, are permitted provided that the following conditions
> + are met:
> +
> + - Redistributions of source code must retain the above copyright
> + notice, this list of conditions and the following disclaimer.
> +
> + - Redistributions in binary form must reproduce the above copyright
> + notice, this list of conditions and the following disclaimer in
> + the documentation and/or other materials provided with the
> + distribution.
> +
> + - Neither the name of Intel Corporation nor the names of its
> + contributors may be used to endorse or promote products derived
> + from this software without specific prior written permission.
> +
> + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
> CONTRIBUTORS
> + "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
> + LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
> FITNESS
> + FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
> + COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
> INDIRECT,
> + INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> + (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
> GOODS OR
> + SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
> + HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
> CONTRACT,
> + STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
> + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
> ADVISED
> + OF THE POSSIBILITY OF SUCH DAMAGE.
> +
> +==========
> +DDP L2TPV3
> +==========
> +
> +DDP profile 0x80000004 adds support for directing L2TPv3 packets based
> +on their session ID for FVL NIC. For DDP introduction, please refer to :
> +
> + https://software.intel.com/en-us/articles/dynamic-device-personalizati
> + on-for-intel-ethernet-700-series
> +
> +l2tpv3oip-l4.pkg defines and supports below pctype packets, also could
> +check the information using command “ddp get info <profile>”
> +after loading the profile. left numbers are pctype values,right are
> +supported packets::
> +
> + 28: IPV4 L2TPV3
> + 38: IPV6 L2TPV3
> +
> +Packet Classifier types and Its Input Set
> +
> + +--------------+--------+-----------------------+-------------------------+
> + | Packet Type | PCType | Hash Input Set | FD Input Set |
> + +--------------+--------+-----------------------+-------------------------+
> + | IPv4,L2TPv3 | 28 | L2TPv3 Session ID | L2TPv3 Session ID |
> + +--------------+--------+-----------------------+-------------------------+
> + | IPv6,L2TPv3 | 38 | L2TPv3 Session ID | L2TPv3 Session ID |
> +
> + +--------------+--------+-----------------------+---------------------
> + ----+
> +
> +
> +Requirements as below
> +=====================
> +
> +Flow API support for flow director rules based on L2TPv3 session ID The
> +current scope is limited to FVL NIC
> +
> +Prerequisites
> +=============
> +
> +1. DPDK version 20.02 or greater
> +
> +2. I40E NIC with FW version 6.0 or greater
> +
> + In your linux terminal enter ethtool -i <interface-name> , this prints out
> + the driver details.
> + Ex ::
> +
> + root@hostname:~/dpdk# ethtool -i <interface-name>
> + driver: i40e
> + version: 2.1.14-k
> + firmware-version: 7.10 0x80006474 1.2527.0
> + expansion-rom-version:
> + bus-info: 0000:02:00.1
> + supports-statistics: yes
> + supports-test: yes
> + supports-eeprom-access: yes
> + supports-register-dump: yes
> + supports-priv-flags: yes
> +
> +*Note: If the firmware version is below 6.0 , the NIC does not support
> +any DDP functionality*
> +
> +3. Download and extract L2TPv3 package
> +
> +
> + https://downloadcenter.intel.com/download/28941/Dynamic-Device-
> Persona
> + lization-L2TPv3
> +
> +4. Bind the Port to the userspace Driver <igb_uio/vfio-pci)::
> +
> + ./usertools/dpdk-devbind.py -b <igb_uio/vfio-pci> <PCI address of
> + device to bind>
> +
> +5. Start the TESTPMD::
> +
> + ./x86_64-native-linuxapp-gcc/build/app/test-pmd/testpmd -c f -n 4 -w
> + <PCI address of device> -- -i --port-topology=chained --txq=64 --rxq=64
> + --pkt-filter-mode=perfect
> +
> + For testpmd commands refer:
> + https://doc.dpdk.org/guides/testpmd_app_ug/
> +
> +6. Set Verbose
> +
> + To enable verbose logging in the testpmd application to get detailed
> + information about rx queues and packet metadata::
> +
> + testpmd > set verbose 1
> +
> +7. To enable required fields as per the indices in the L2TPv3 Packet field
> + vector (refer Dynamic_Device_Personalization_L2TPv3_Rev1.x)
> +
> + To enable the specific field in the vector for a PCTYPE , the following
> + command may be used::
> +
> + testpmd> port config <port_id> pctype <PCTYPE> fdir_inset set field
> + <field_index>
> +
> + To check if a specific field in the vector is set for a PCTYPE, the
> + following command may be used::
> +
> + testpmd> port config <port_id> pctype <PCTYPE> fdir_inset get field
> + <field_index>
> +
> + To clear any specific field in the vector for a PCTYPE, the following
> + command may be used::
> +
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear field
> + <field_index>
> +
> + To clear all fields for a specific PCTYPE, the following commands may
> + be used::
> +
> + testpmd> port config <port_id> pctype <PCTYPE> fdir_inset clear all
> +
> +*NOTE: Changes such as enabling/disabling of specific field in the
> +vector for a PCTYPE will remain applied across restarts of testpmd
> application.
> +It is good practice to explicitly set the desired field in the vector
> +for a PCTYPE upon start of testpmd.*
> +
> +
> +Test Case : Adding L2TPv3 profile to the port
> +=============================================
> +
> +1. Stop testpmd port before loading profile::
> +
> + testpmd > port stop <port_id>
> +
> +2. Load l2tpv3oip-l4.pkg file to the memory buffer and save the existing
> + configuration to the l2tpv3oip-l4.bak file::
> +
> + testpmd > ddp add <port_id> <path>/l2tpv3oip-l4.pkg,<path>/
> + l2tpv3oip-l4.bak
> +
> +3. Check to see if the profile is loaded ::
> +
> + testpmd> ddp get list <port_id>
> + Track id: 0x80000004
> + Version: 1.0.0.0
> + Profile name: L2TPv3oIP with L4 payload
> +
> +Test Case : Deleting L2TPv3 profile from the port
> +=================================================
> +
> +This test is intended to revert to the original DDP profile of the port
> +without reset
> +
> +1. Stop testpmd port before loading profile::
> +
> + testpmd > port stop <port_id>
> +
> +2. Remove profile from the network adapter and restore original
> + configuration::
> +
> + testpmd > ddp del <port_id> <path>/l2tpv3oip-l4.bak
> +
> +3. Check to see if the profile is deleted::
> +
> + testpmd> ddp get list <port_id>
> + Profile number is: 0
> +
> +Test Case : Adding and deleting Flow Director rules
> +===================================================
> +
> +1. To Add l2tpv3 flow director rules::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip
> session_id
> + is 1 / end actions queue index 1 / end
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip
> session_id
> + is 2 / end actions queue index 2 / end
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip
> session_id
> + is 3 / end actions queue index 3 / end
> +
> +2. To List the rules using the flow list command with port number::
> +
> + testpmd> flow list <port_id>
> + ID Group Prio Attr Rule
> + 0 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
> + 1 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
> + 2 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
> +
> +3. To delete a single rule ::
> +
> + testpmd> flow destroy <port_id> rule 0
> + Flow rule #0 destroyed
> + testpmd> flow list <port_id>
> + ID Group Prio Attr Rule
> + 1 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
> + 2 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
> + <flow rule with ID 0 should not be listed>
> +
> +4. To delete all the rules::
> +
> + testpmd> flow flush <port_id>
> + testpmd> flow list <port_id>
> + testpmd>
> + (No List is printed)
> +
> +Test Case: L2TPv3 over IPv4 packet
> +==================================
> +
> +1. Add l2tpv3 flow director rule, set sessionID as 1, queue 1::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip
> session_id
> + is 1 / end actions queue index 1 / end
> +
> +2. Send L2TPv3 packet with session ID matching the configured rule, Packets
> + should be received on queue 1::
> +
> + p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x01')/Raw('x' * 20)
> +
> +3. Send L2TPv3 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x11')/Raw('x' * 20)
> +
> +Test Case: L2TPv3 over IPv6 packet
> +==================================
> +
> +1. Add l2tpv3 flow director rule, set sessionID as 1000, queue 2::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip
> session_id
> + is 1000 / end actions queue index 2 / end
> +
> +2. Send L2TPv3 packet with session ID matching the configured rule, Packets
> + should be received on queue 2::
> +
> + p=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
> +
> +3. Send L2TPv3 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\x88')/Raw('x' * 20)
> +
> +Test Case: L2TPv3oIPv4 with L2TPv3oIPv6 configuration
> +========================================================
> +
> +1. Add l2tpv3 flow director rules , set sessionID as 1001, queue 1 for IPv4
> + and IPv6 flows::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip
> session_id
> + is 1001 / end actions queue index 1 / end
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip
> session_id
> + is 1001 / end actions queue index 1 / end
> +
> +2. Send L2TPv3 packets for IPv4 and IPv6 with session ID same as configured
> + rule, Packets should be received on queue 1::
> +
> + P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
> +
> + P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
> +
> +
> +3. Send L2TPv3 packets(IPv4 and IPv6) with session ID not matching the
> + configured rules, Packet should be received on queue 0::
> +
> + P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xf9')/Raw('x' * 20)
> +
> + P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xf9')/Raw('x' * 20)
> +
> +Test Case: UDP, L2TPv3oIPv4 with L2TPv3oIPv6 configurations
> +============================================================
> +
> +1. Add l2tpv3 flow director rules , set sessionID as 1001, queue 1 for IPv4
> + and queue 2 for IPv6 flows::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip
> session_id
> + is 1001 / end actions queue index 1 / end
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip
> session_id
> + is 1001 / end actions queue index 2 / end
> +
> +2. Add UDP flow director rule , set queue 3 for UDP packets::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 / udp / end
> actions
> + queue index 3 / end
> +
> +3. Send L2TPv3 packets for IPv4 and IPv6 with session ID same as configured
> + rules, Packets should be received on queue 1 and queue 2 respectively::
> +
> + P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
> +
> + P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
> +
> +4. Send L2TPv3 packets(IPv4 and IPv6) with session ID not matching the
> + configured rules, Packet should be received on queue 0::
> +
> + P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\x09')/Raw('x' * 20)
> +
> + P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\x09')/Raw('x' * 20)
> +
> +5. Send IPv4/UDP packet. Verify that the packet is received on queue 3::
> +
> + P_UDP=Ether()/IP()/UDP()
> +
> +Test Case: L2TPv3oIPv4 configuration with specific SIP and DIP
> +==============================================================
> +
> +1. Stop testpmd port before loading profile::
> +
> + testpmd > port stop <port_id>
> +
> +2. Set the fdir inset as follows::
> +
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field
> + 45
> +
> +3. Start testpmd port ::
> +
> + testpmd> port start <port_id>
> +
> +4. Start forwarding::
> +
> + testpmd> start
> +
> +5. Add l2tpv3 flow director rule, set sessionID as 1 queue 1::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1
> dst
> + is 20.10.10.20 / l2tpv3oip session_id is 1 / end actions queue index 10
> + / end
> +
> +6. Send L2TPv3 packet with SIP,DIP and session ID matching the configured
> rule,
> + Packets should be received on queue 10::
> +
> + p=Ether()/IP(src="10.10.10.1",dst="20.10.10.20",proto=115)/
> + Raw('\x00\x00\x00\x01')/Raw('x' * 20)
> +
> +7. Send L2TPv3 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether(src="00:00:00:00:00:02", dst="3C:FD:FE:A5:49:88")/IP(proto=115)
> + /Raw('\x00\x00\x00\x44')/Raw('x' * 20)
> +
> +8. Send L2TPv3 packet with SIP not matching the configured rule,
> + Packets should be received on queue 10::
> +
> + p=Ether()/IP(src="100.10.10.1",dst="20.10.10.20",proto=115)/
> + Raw('\x00\x00\x00\x01')/Raw('x' * 20)
> +
> +9. Send L2TPv3 packet with DIP not matching the configured rule,
> + Packets should be received on queue 10::
> +
> + p=Ether()/IP(src="10.10.10.1",dst="200.10.10.20",proto=115)/
> + Raw('\x00\x00\x00\x01')/Raw('x' * 20)
> +
> +Test Case: L2TPv3oIPv6 configuration with specific SIP and DIP
> +==============================================================
> +
> +1. Set the fdir inset as follows ::
> +
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field
> + 45
> +
> +3. Start testpmd port ::
> +
> + testpmd> port start <port_id>
> +
> +4. Start forwarding ::
> +
> + testpmd> start
> +
> +5. Add l2tpv3 flow director rule, set sessionID as 1000 queue 20::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv6 src is
> 1:2:3:4:5:6:7:8
> + dst is 8:7:6:5:4:3:2:1 / l2tpv3oip session_id is 1000 / end actions queue
> + index 20 / end
> +
> +6. Send L2TPv3 packet with session ID, SIP and DIP matching the configured
> + rule, Packets should be received on queue 20::
> +
> + p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
> + Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
> +
> +7. Send L2TPv3 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
> + Raw('\x00\x00\x03\xff')/Raw('x' * 20)
> +
> +8. Send L2TPv3 packet with Source IP not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
> + Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
> +
> +9. Send L2TPv3 packet with Destination IP not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1111",nh=115)/
> + Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
> +
> +Test Case: L2TPv3oIPv4 configuration with specific SIP
> +======================================================
> +
> +1. Stop testpmd port before loading profile::
> +
> + testpmd > port stop all
> +
> +2. Set the fdir inset as follows ::
> +
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field
> + 45
> +
> +3. Start testpmd port ::
> +
> + testpmd> port start <port_id>
> +
> +4. Start forwarding ::
> +
> + testpmd> start
> +
> +5. Add l2tpv3 flow director rule, set sessionID as 1, queue 10::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1
> /
> + l2tpv3oip session_id is 1 / end actions queue index 10 / end
> +
> +6. Send L2TPv3 packet with SIP and session ID matching the configured rule,
> + Packets should be received on queue 10::
> +
> + p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x01')/
> + Raw('x' * 20)
> +
> +7. Send L2TPv3 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> +
> + p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x21')/
> + Raw('x' * 20)
> +
> +8. Send L2TPv3 packet with SIP not matching the configured rule, Packets
> + should be received on queue 0::
> +
> + p=Ether()/IP(src="20.20.20.1",proto=115)/Raw('\x00\x00\x00\x01')/
> + Raw('x' * 20)
> +
> +Test Case: L2TPv3oIPv6 configuration with specific SIP
> +======================================================
> +
> +1. Stop testpmd port before loading profile::
> +
> + testpmd > port stop <port_id>
> +
> +2. Set the fdir inset as follows ::
> +
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field
> + 45
> +
> +3. Start testpmd port ::
> +
> + testpmd> port start <port_id>
> +
> +4. Start forwarding ::
> +
> + testpmd> start
> +
> +5. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv6 src is
> 1:2:3:4:5:6:7:8
> + / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
> +
> +6. Send L2TPv3 packet with SIP and session ID matching the configured rule,
> + Packets should be received on queue 20::
> +
> + p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
> + Raw('x' * 20)
> +
> +7. Send L2TPv3 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xff')/
> + Raw('x' * 20)
> +
> +8. Send L2TPv3 packet with SIP not matching the configured rule, Packet
> + should be received on queue 0::
> +
> +
> p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
> + Raw('x' * 20)
> +
> +Test Case: L2TPv3oIPv4 configuration with specific DIP
> +======================================================
> +
> +1. Stop testpmd port before loading profile::
> +
> + testpmd > port stop <port_id>
> +
> +2. Set the fdir inset as follows ::
> +
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field
> + 45
> +
> +3. Start testpmd port ::
> +
> + testpmd> port start <port_id>
> +
> +4. Start forwarding ::
> +
> + testpmd> start
> +
> +5. Add l2tpv3 flow director rule, set sessionID as 1, queue 10::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 dst is
> 20.10.10.20
> + / l2tpv3oip session_id is 1 / end actions queue index 10 / end
> +
> +6. Send L2TPv3 packet with DIP and session ID matching the configured rule,
> + Packets should be received on queue 10::
> +
> + p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
> + Raw('x' * 20)
> +
> +7. Send L2TPv3 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x44')/
> + Raw('x' * 20)
> +
> +8. Send L2TPv3 packet with DIP not matching the configured rule, Packet
> + should be received on queue 0::
> +
> + p=Ether()/IP(dst="2220.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
> + Raw('x' * 20)
> +
> +Test Case: L2TPv3oIPv6 configuration with specific DIP
> +======================================================
> +
> +1. Stop testpmd port before loading profile::
> +
> + testpmd > port stop <port_id>
> +
> +2. Set the fdir inset as follows ::
> +
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field
> + 45
> +
> +3. Start testpmd port ::
> +
> + testpmd> port start <port_id>
> +
> +4. Start forwarding ::
> +
> + testpmd> start
> +
> +5. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv6 dst is
> 8:7:6:5:4:3:2:1
> + / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
> +
> +6. Send L2TPv3 packet with session ID, DIP matching the configured rule,
> + Packets should be received on queue 20::
> +
> + p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
> + Raw('x' * 20)
> +
> +7. Send L2TPv3 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xff')/
> + Raw('x' * 20)
> +
> +8. Send L2TPv3 packet with DIP not matching the configured rule, Packet
> + should be received on queue 0::
> +
> +
> p=Ether()/IPv6(dst="8888:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
> + Raw('x' * 20)
> +
> +Test Case: L2TPv3 with specific IPv4 SIP and IPv6 SIP configured
> +together
> +===============================================================
> ========
> +==
> +
> +1. Stop testpmd port before loading profile::
> +
> + testpmd > port stop <port_id>
> +
> +2. Set the fdir inset as follows ::
> +
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field
> + 45
> +
> +3. Start testpmd port ::
> +
> + testpmd> port start <port_id>
> +
> +4. Start forwarding ::
> +
> + testpmd> start
> +
> +5. Add l2tpv3 flow director rule,set sessionID as 1,queue 10 for IPv4 flow::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1
> /
> + l2tpv3oip session_id is 1 / end actions queue index 10 / end
> +
> +6. Add l2tpv3 flow director rule,set sessionID as 1000,
> + queue 20 for IPv6 flow::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv6 src is
> 1:2:3:4:5:6:7:8
> + / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
> +
> +7. Send L2TPv3 IPv4 packet with SIP and session ID matching the configured
> + rule, Packets should be received on queue 10::
> +
> + p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x01')/
> + Raw('x' * 20)
> +
> +8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x44')/Raw('x' * 20)
> +
> +9. Send L2TPv3 IPv4 packet with SIP not matching the configured rule,
> + Packets should be received on queue 0::
> +
> + p=Ether()/IP(src="20.20.20.1",proto=115)/Raw('\x00\x00\x00\x01')/
> + Raw('x' * 20)
> +
> +10. Send L2TPv3 IPv6 packet with SIP and session ID matching the
> configured
> + rule, Packets should be received on queue 20::
> +
> + p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
> + Raw('x' * 20)
> +
> +11. Send L2TPv3 IPv6 packet with session ID not matching the configured
> + rule, Packet should be received on queue 0::
> +
> + p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xff')
> + /Raw('x' * 20)
> +
> +12. Send L2TPv3 IPv6 packet with SIP not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')
> + /Raw('x' * 20)
> +
> +Test Case: L2TPv3 with specific IPv4 DIP and IPv6 DIP configured
> +together
> +===============================================================
> ========
> +==
> +
> +1. Stop testpmd port before loading profile::
> +
> + testpmd > port stop <port_id>
> +
> +2. Set the fdir inset as follows ::
> +
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field
> + 45
> +
> +3. Start testpmd port ::
> +
> + testpmd> port start <port_id>
> +
> +4. Start forwarding ::
> +
> + testpmd> start
> +
> +5. Add l2tpv3 flow director rule, set sessionID as 1 queue 10 for IPv4::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 dst is
> 20.10.10.20 /
> + l2tpv3oip session_id is 1 / end actions queue index 10 / end
> +
> +6. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20 for IPv6::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv6 dst is
> 8:7:6:5:4:3:2:1
> + / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
> +
> +7. Send L2TPv3 IPv4 packet with DIP and session ID matching the configured
> + rule,Packets should be received on queue 10::
> +
> + p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
> + Raw('x' * 20)
> +
> +8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x21')/
> + Raw('x' * 20)
> +
> +9. Send L2TPv3 IPv4 packet with DIP not matching the configured rule,
> Packet
> + should be received on queue 0::
> +
> +
> + p=Ether()/IP(dst="2220.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/Ra
> + w('x' * 20)
> +
> +10. Send L2TPv3 packet with session ID, DIP matching the configured rule,
> + Packets should be received on queue 20::
> +
> + p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
> + Raw('x' * 20)
> +
> +11. Send L2TPv3 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xff')/
> + Raw('x' * 20)
> +
> +12. Send L2TPv3 packet with DIP not matching the configured rule, Packet
> + should be received on queue 0::
> +
> +
> p=Ether()/IPv6(dst="8888:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
> + Raw('x' * 20)
> +
> +Test Case: L2TPv3 with IPv4 SIP, DIP and IPv6 SIP, DIP configured
> +together
> +===============================================================
> ========
> +===
> +
> +1. Stop testpmd port before loading profile::
> +
> + testpmd > port stop <port_id>
> +
> +2. Set the fdir inset as follows ::
> +
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
> + testpmd> port config <port_id> pctype <pctype> fdir_inset set field
> + 45
> +
> +3. Start testpmd port ::
> +
> + testpmd> port start <port_id>
> +
> +4. Start forwarding ::
> +
> + testpmd> start
> +
> +5. Add l2tpv3 flow director rule,set sessionID as 1,queue 10 for IPv4 flow::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1
> dst
> + is 20.10.10.20 / l2tpv3oip session_id is 1 / end actions queue index 10
> + / end
> +
> +6. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20 for IPv6
> + flow ::
> +
> + testpmd> flow create <port_id> ingress pattern eth / ipv6 src is
> 1:2:3:4:5:6:7:8
> + ipv6 dst is 8:7:6:5:4:3:2:1 / l2tpv3oip session_id is 1000 / end actions
> + queue index 20 / end
> +
> +7. Send L2TPv3 IPv4 packet with SIP, DIP and session ID matching the
> + configured rule, Packets should be received on queue 10::
> +
> + p=Ether()/IP(src="10.10.10.1", dst= "20.10.10.20",proto=115)/
> + Raw('\x00\x00\x00\x01')/Raw('x' * 20)
> +
> +8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IP(src="10.10.10.1", dst= "20.10.10.20",proto=115)/
> + Raw('\x00\x00\x00\x11')/Raw('x' * 20)
> +
> +9. Send L2TPv3 IPv4 packet with SIP not matching the configured rule,
> + Packets should be received on queue 0::
> +
> + p=Ether()/IP(src="100.10.10.1", dst= "20.10.10.20",proto=115)/
> + Raw('\x00\x00\x00\x01')/Raw('x' * 20)
> +
> +10. Send L2TPv3 IPv4 packet with DIP not matching the configured rule,
> Packet
> + should be received on queue 0::
> +
> + p=Ether()/IP(src="10.10.10.1", dst="220.10.10.20",proto=115)/
> + Raw('\x00\x00\x00\x01')/Raw('x' * 20)
> +
> +11. Send L2TPv3 IPv6 packet with SIP, DIP and session ID matching the
> + configured rule, Packets should be received on queue 20::
> +
> + p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)/
> + Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
> +
> +12. Send L2TPv3 IPv6 packet with session ID not matching the configured
> rule,
> + Packet should be received on queue 0::
> +
> + p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)/
> + Raw('\x00\x00\x03\xF8')/Raw('x' * 20)
> +
> +13. Send L2TPv3 IPv6 packet with SIP not matching the configured rule,
> Packet
> + should be received on queue 0::
> +
> + p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)
> + /Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
> +
> +14. Send L2TPv3 IPv6 packet with DIP not matching the configured rule,
> Packet
> + should be received on queue 0::
> +
> + p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6
> dst="8888:7:6:5:4:3:2:1",nh=115)/
> + Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
> --
> 2.17.1
^ permalink raw reply [flat|nested] 4+ messages in thread
* [dts] [PATCH] L2TPv3 test plan document
@ 2020-02-14 9:42 Varalakshmi
0 siblings, 0 replies; 4+ messages in thread
From: Varalakshmi @ 2020-02-14 9:42 UTC (permalink / raw)
To: dts; +Cc: Varalakshmi
Adding L2TPv3 test plan document.
It contains prerequisites and different test scenarios.
Signed-off-by: Varalakshmi <varalakshmi.s@intel.com>
---
test_plans/ddp_l2tpv3_test_plan.rst | 900 ++++++++++++++++++++++++++++
1 file changed, 900 insertions(+)
create mode 100644 test_plans/ddp_l2tpv3_test_plan.rst
diff --git a/test_plans/ddp_l2tpv3_test_plan.rst b/test_plans/ddp_l2tpv3_test_plan.rst
new file mode 100644
index 0000000..4c0b881
--- /dev/null
+++ b/test_plans/ddp_l2tpv3_test_plan.rst
@@ -0,0 +1,900 @@
+.. Copyright (c) <2018>, Intel Corporation
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions
+ are met:
+
+ - Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+ - Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+ - Neither the name of Intel Corporation nor the names of its
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
+ OF THE POSSIBILITY OF SUCH DAMAGE.
+
+==========
+DDP L2TPV3
+==========
+
+DDP profile 0x80000004 adds support for directing L2TPv3 packets based on
+their session ID for FVL NIC. For DDP introduction, please refer to :
+
+ https://software.intel.com/en-us/articles/dynamic-device-personalization-for-intel-ethernet-700-series
+
+l2tpv3oip-l4.pkg defines and supports below pctype packets, also
+could check the information using command “ddp get info <profile>”
+after loading the profile. left numbers are pctype values,right are
+supported packets::
+
+ 28: IPV4 L2TPV3
+ 38: IPV6 L2TPV3
+
+Packet Classifier types and Its Input Set
+
+ +--------------+--------+-----------------------+-------------------------+
+ | Packet Type | PCType | Hash Input Set | FD Input Set |
+ +--------------+--------+-----------------------+-------------------------+
+ | IPv4,L2TPv3 | 28 | L2TPv3 Session ID | L2TPv3 Session ID |
+ +--------------+--------+-----------------------+-------------------------+
+ | IPv6,L2TPv3 | 38 | L2TPv3 Session ID | L2TPv3 Session ID |
+ +--------------+--------+-----------------------+-------------------------+
+
+
+Requirements as below
+=====================
+
+Flow API support for flow director rules based on L2TPv3 session ID
+The current scope is limited to FVL NIC
+
+Prerequisites
+=============
+
+1. DPDK version 20.02 or greater
+
+2. I40E NIC with FW version 6.0 or greater
+
+ In your linux terminal enter ethtool -i <interface-name> , this prints out
+ the driver details.
+ Ex ::
+
+ root@hostname:~/dpdk# ethtool -i <interface-name>
+ driver: i40e
+ version: 2.1.14-k
+ firmware-version: 7.10 0x80006474 1.2527.0
+ expansion-rom-version:
+ bus-info: 0000:02:00.1
+ supports-statistics: yes
+ supports-test: yes
+ supports-eeprom-access: yes
+ supports-register-dump: yes
+ supports-priv-flags: yes
+
+*Note: If the firmware version is below 6.0 , the NIC does not support
+any DDP functionality*
+
+3. Download and extract L2TPv3 package
+
+ https://downloadcenter.intel.com/download/28941/Dynamic-Device-Personalization-L2TPv3
+
+4. Bind the Port to the userspace Driver <igb_uio/vfio-pci)::
+
+ ./usertools/dpdk-devbind.py -b <igb_uio/vfio-pci> <PCI address of device to bind>
+
+5. Start the TESTPMD::
+
+ ./x86_64-native-linuxapp-gcc/build/app/test-pmd/testpmd -c f -n 4 -w
+ <PCI address of device> -- -i --port-topology=chained --txq=64 --rxq=64
+ --pkt-filter-mode=perfect
+
+ For testpmd commands refer: https://doc.dpdk.org/guides/testpmd_app_ug/
+
+6. Set Verbose
+
+ To enable verbose logging in the testpmd application to get detailed
+ information about rx queues and packet metadata::
+
+ testpmd > set verbose 1
+
+7. To enable required fields as per the indices in the L2TPv3 Packet field
+ vector (refer Dynamic_Device_Personalization_L2TPv3_Rev1.x)
+
+ To enable the specific field in the vector for a PCTYPE , the following
+ command may be used::
+
+ testpmd> port config <port_id> pctype <PCTYPE> fdir_inset set field
+ <field_index>
+
+ To check if a specific field in the vector is set for a PCTYPE, the
+ following command may be used::
+
+ testpmd> port config <port_id> pctype <PCTYPE> fdir_inset get field
+ <field_index>
+
+ To clear any specific field in the vector for a PCTYPE, the following
+ command may be used::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear field
+ <field_index>
+
+ To clear all fields for a specific PCTYPE, the following commands may
+ be used::
+
+ testpmd> port config <port_id> pctype <PCTYPE> fdir_inset clear all
+
+*NOTE: Changes such as enabling/disabling of specific field in the vector
+for a PCTYPE will remain applied across restarts of testpmd application.
+It is good practice to explicitly set the desired field in the vector for
+a PCTYPE upon start of testpmd.*
+
+
+Test Case : Adding L2TPv3 profile to the port
+=============================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Load l2tpv3oip-l4.pkg file to the memory buffer and save the existing
+ configuration to the l2tpv3oip-l4.bak file::
+
+ testpmd > ddp add <port_id> <path>/l2tpv3oip-l4.pkg,<path>/
+ l2tpv3oip-l4.bak
+
+3. Check to see if the profile is loaded ::
+
+ testpmd> ddp get list <port_id>
+ Track id: 0x80000004
+ Version: 1.0.0.0
+ Profile name: L2TPv3oIP with L4 payload
+
+Test Case : Deleting L2TPv3 profile from the port
+=================================================
+
+This test is intended to revert to the original DDP profile of the port
+without reset
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Remove profile from the network adapter and restore original
+ configuration::
+
+ testpmd > ddp del <port_id> <path>/l2tpv3oip-l4.bak
+
+3. Check to see if the profile is deleted::
+
+ testpmd> ddp get list <port_id>
+ Profile number is: 0
+
+Test Case : Adding and deleting Flow Director rules
+===================================================
+
+1. To Add l2tpv3 flow director rules::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1 / end actions queue index 1 / end
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 2 / end actions queue index 2 / end
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 3 / end actions queue index 3 / end
+
+2. To List the rules using the flow list command with port number::
+
+ testpmd> flow list <port_id>
+ ID Group Prio Attr Rule
+ 0 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ 1 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ 2 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+
+3. To delete a single rule ::
+
+ testpmd> flow destroy <port_id> rule 0
+ Flow rule #0 destroyed
+ testpmd> flow list <port_id>
+ ID Group Prio Attr Rule
+ 1 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ 2 0 0 i-- ETH IPV4 L2TPV3 => QUEUE
+ <flow rule with ID 0 should not be listed>
+
+4. To delete all the rules::
+
+ testpmd> flow flush <port_id>
+ testpmd> flow list <port_id>
+ testpmd>
+ (No List is printed)
+
+Test Case: L2TPv3 over IPv4 packet
+==================================
+
+1. Add l2tpv3 flow director rule, set sessionID as 1, queue 1::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1 / end actions queue index 1 / end
+
+2. Send L2TPv3 packet with session ID matching the configured rule, Packets
+ should be received on queue 1::
+
+ p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+3. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x11')/Raw('x' * 20)
+
+Test Case: L2TPv3 over IPv6 packet
+==================================
+
+1. Add l2tpv3 flow director rule, set sessionID as 1000, queue 2::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip session_id
+ is 1000 / end actions queue index 2 / end
+
+2. Send L2TPv3 packet with session ID matching the configured rule, Packets
+ should be received on queue 2::
+
+ p=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+3. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\x88')/Raw('x' * 20)
+
+Test Case: L2TPv3oIPv4 with L2TPv3oIPv6 configuration
+========================================================
+
+1. Add l2tpv3 flow director rules , set sessionID as 1001, queue 1 for IPv4
+ and IPv6 flows::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1001 / end actions queue index 1 / end
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip session_id
+ is 1001 / end actions queue index 1 / end
+
+2. Send L2TPv3 packets for IPv4 and IPv6 with session ID same as configured
+ rule, Packets should be received on queue 1::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+
+3. Send L2TPv3 packets(IPv4 and IPv6) with session ID not matching the
+ configured rules, Packet should be received on queue 0::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xf9')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xf9')/Raw('x' * 20)
+
+Test Case: UDP, L2TPv3oIPv4 with L2TPv3oIPv6 configurations
+============================================================
+
+1. Add l2tpv3 flow director rules , set sessionID as 1001, queue 1 for IPv4
+ and queue 2 for IPv6 flows::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / l2tpv3oip session_id
+ is 1001 / end actions queue index 1 / end
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 / l2tpv3oip session_id
+ is 1001 / end actions queue index 2 / end
+
+2. Add UDP flow director rule , set queue 3 for UDP packets::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 / udp / end actions
+ queue index 3 / end
+
+3. Send L2TPv3 packets for IPv4 and IPv6 with session ID same as configured
+ rules, Packets should be received on queue 1 and queue 2 respectively::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\xe9')/Raw('x' * 20)
+
+4. Send L2TPv3 packets(IPv4 and IPv6) with session ID not matching the
+ configured rules, Packet should be received on queue 0::
+
+ P_IPV4=Ether()/IP(proto=115)/Raw('\x00\x00\x03\x09')/Raw('x' * 20)
+
+ P_IPV6=Ether()/IPv6(nh=115)/Raw('\x00\x00\x03\x09')/Raw('x' * 20)
+
+5. Send IPv4/UDP packet. Verify that the packet is received on queue 3::
+
+ P_UDP=Ether()/IP()/UDP()
+
+Test Case: L2TPv3oIPv4 configuration with specific SIP and DIP
+==============================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1 queue 1::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 dst
+ is 20.10.10.20 / l2tpv3oip session_id is 1 / end actions queue index 10
+ / end
+
+6. Send L2TPv3 packet with SIP,DIP and session ID matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",dst="20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether(src="00:00:00:00:00:02", dst="3C:FD:FE:A5:49:88")/IP(proto=115)
+ /Raw('\x00\x00\x00\x44')/Raw('x' * 20)
+
+8. Send L2TPv3 packet with SIP not matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="100.10.10.1",dst="20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+9. Send L2TPv3 packet with DIP not matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",dst="200.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+Test Case: L2TPv3oIPv6 configuration with specific SIP and DIP
+==============================================================
+
+1. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1000 queue 20::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ dst is 8:7:6:5:4:3:2:1 / l2tpv3oip session_id is 1000 / end actions queue
+ index 20 / end
+
+6. Send L2TPv3 packet with session ID, SIP and DIP matching the configured
+ rule, Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xff')/Raw('x' * 20)
+
+8. Send L2TPv3 packet with Source IP not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+9. Send L2TPv3 packet with Destination IP not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",dst="8:7:6:5:4:3:2:1111",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+Test Case: L2TPv3oIPv4 configuration with specific SIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop all
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1, queue 10::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 /
+ l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Send L2TPv3 packet with SIP and session ID matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+
+ p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x21')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with SIP not matching the configured rule, Packets
+ should be received on queue 0::
+
+ p=Ether()/IP(src="20.20.20.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3oIPv6 configuration with specific SIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+6. Send L2TPv3 packet with SIP and session ID matching the configured rule,
+ Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xff')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with SIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3oIPv4 configuration with specific DIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1, queue 10::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 dst is 20.10.10.20
+ / l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Send L2TPv3 packet with DIP and session ID matching the configured rule,
+ Packets should be received on queue 10::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x44')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IP(dst="2220.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3oIPv6 configuration with specific DIP
+======================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 dst is 8:7:6:5:4:3:2:1
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+6. Send L2TPv3 packet with session ID, DIP matching the configured rule,
+ Packets should be received on queue 20::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+7. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xff')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8888:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3 with specific IPv4 SIP and IPv6 SIP configured together
+=========================================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule,set sessionID as 1,queue 10 for IPv4 flow::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 /
+ l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Add l2tpv3 flow director rule,set sessionID as 1000,
+ queue 20 for IPv6 flow::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+7. Send L2TPv3 IPv4 packet with SIP and session ID matching the configured
+ rule, Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(proto=115)/Raw('\x00\x00\x00\x44')/Raw('x' * 20)
+
+9. Send L2TPv3 IPv4 packet with SIP not matching the configured rule,
+ Packets should be received on queue 0::
+
+ p=Ether()/IP(src="20.20.20.1",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+10. Send L2TPv3 IPv6 packet with SIP and session ID matching the configured
+ rule, Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+11. Send L2TPv3 IPv6 packet with session ID not matching the configured
+ rule, Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xff')
+ /Raw('x' * 20)
+
+12. Send L2TPv3 IPv6 packet with SIP not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",nh=115)/Raw('\x00\x00\x03\xe8')
+ /Raw('x' * 20)
+
+Test Case: L2TPv3 with specific IPv4 DIP and IPv6 DIP configured together
+=========================================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule, set sessionID as 1 queue 10 for IPv4::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 dst is 20.10.10.20 /
+ l2tpv3oip session_id is 1 / end actions queue index 10 / end
+
+6. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20 for IPv6::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 dst is 8:7:6:5:4:3:2:1
+ / l2tpv3oip session_id is 1000 / end actions queue index 20 / end
+
+7. Send L2TPv3 IPv4 packet with DIP and session ID matching the configured
+ rule,Packets should be received on queue 10::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/
+ Raw('x' * 20)
+
+8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(dst="20.10.10.20",proto=115)/Raw('\x00\x00\x00\x21')/
+ Raw('x' * 20)
+
+9. Send L2TPv3 IPv4 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IP(dst="2220.10.10.20",proto=115)/Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+10. Send L2TPv3 packet with session ID, DIP matching the configured rule,
+ Packets should be received on queue 20::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+11. Send L2TPv3 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xff')/
+ Raw('x' * 20)
+
+12. Send L2TPv3 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(dst="8888:7:6:5:4:3:2:1",nh=115)/Raw('\x00\x00\x03\xe8')/
+ Raw('x' * 20)
+
+Test Case: L2TPv3 with IPv4 SIP, DIP and IPv6 SIP, DIP configured together
+==========================================================================
+
+1. Stop testpmd port before loading profile::
+
+ testpmd > port stop <port_id>
+
+2. Set the fdir inset as follows ::
+
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset clear all
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 13
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 14
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 15
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 16
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 17
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 18
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 19
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 20
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 21
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 22
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 23
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 24
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 25
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 26
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 27
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 28
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 44
+ testpmd> port config <port_id> pctype <pctype> fdir_inset set field 45
+
+3. Start testpmd port ::
+
+ testpmd> port start <port_id>
+
+4. Start forwarding ::
+
+ testpmd> start
+
+5. Add l2tpv3 flow director rule,set sessionID as 1,queue 10 for IPv4 flow::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv4 src is 10.10.10.1 dst
+ is 20.10.10.20 / l2tpv3oip session_id is 1 / end actions queue index 10
+ / end
+
+6. Add l2tpv3 flow director rule, set sessionID as 1000, queue 20 for IPv6
+ flow ::
+
+ testpmd> flow create <port_id> ingress pattern eth / ipv6 src is 1:2:3:4:5:6:7:8
+ ipv6 dst is 8:7:6:5:4:3:2:1 / l2tpv3oip session_id is 1000 / end actions
+ queue index 20 / end
+
+7. Send L2TPv3 IPv4 packet with SIP, DIP and session ID matching the
+ configured rule, Packets should be received on queue 10::
+
+ p=Ether()/IP(src="10.10.10.1", dst= "20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+8. Send L2TPv3 IPv4 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IP(src="10.10.10.1", dst= "20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x11')/Raw('x' * 20)
+
+9. Send L2TPv3 IPv4 packet with SIP not matching the configured rule,
+ Packets should be received on queue 0::
+
+ p=Ether()/IP(src="100.10.10.1", dst= "20.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+10. Send L2TPv3 IPv4 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IP(src="10.10.10.1", dst="220.10.10.20",proto=115)/
+ Raw('\x00\x00\x00\x01')/Raw('x' * 20)
+
+11. Send L2TPv3 IPv6 packet with SIP, DIP and session ID matching the
+ configured rule, Packets should be received on queue 20::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+12. Send L2TPv3 IPv6 packet with session ID not matching the configured rule,
+ Packet should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xF8')/Raw('x' * 20)
+
+13. Send L2TPv3 IPv6 packet with SIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(src="1111:2:3:4:5:6:7:8",ipv6 dst="8:7:6:5:4:3:2:1",nh=115)
+ /Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
+
+14. Send L2TPv3 IPv6 packet with DIP not matching the configured rule, Packet
+ should be received on queue 0::
+
+ p=Ether()/IPv6(src="1:2:3:4:5:6:7:8",ipv6 dst="8888:7:6:5:4:3:2:1",nh=115)/
+ Raw('\x00\x00\x03\xe8')/Raw('x' * 20)
--
2.17.1
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2020-02-25 1:22 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-02-17 9:05 [dts] [PATCH] L2TPv3 Test plan document Varalakshmi
2020-02-24 5:16 ` Peng, Yuan
2020-02-25 1:22 ` Tu, Lijuan
-- strict thread matches above, loose matches on Subject: below --
2020-02-14 9:42 [dts] [PATCH] L2TPv3 test " Varalakshmi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).