From: "Tu, Lijuan" <lijuan.tu@intel.com>
To: "Fu, Qi" <qi.fu@intel.com>, "dts@dpdk.org" <dts@dpdk.org>
Cc: "Fu, Qi" <qi.fu@intel.com>
Subject: Re: [dts] [PATCH V1]test_plans: add l2tp and esp coverage test plan
Date: Wed, 3 Jun 2020 02:30:24 +0000 [thread overview]
Message-ID: <8CE3E05A3F976642AAB0F4675D0AD20E0BC587D2@SHSMSX101.ccr.corp.intel.com> (raw)
In-Reply-To: <20200602181747.89632-1-qi.fu@intel.com>
Applied, thanks
> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of Fu Qi
> Sent: Wednesday, June 3, 2020 2:18 AM
> To: dts@dpdk.org
> Cc: Fu, Qi <qi.fu@intel.com>
> Subject: [dts] [PATCH V1]test_plans: add l2tp and esp coverage test plan
>
> Add l2tpv3 and esp coverage test plan. test checksum and l2 tag for
> these two protocols.
>
> Signed-off-by: Fu Qi <qi.fu@intel.com>
> ---
> test_plans/l2tp_esp_coverage_test_plan.rst | 1458 ++++++++++++++++++++
> 1 file changed, 1458 insertions(+)
> create mode 100644 test_plans/l2tp_esp_coverage_test_plan.rst
>
> diff --git a/test_plans/l2tp_esp_coverage_test_plan.rst
> b/test_plans/l2tp_esp_coverage_test_plan.rst
> new file mode 100644
> index 0000000..b8eff78
> --- /dev/null
> +++ b/test_plans/l2tp_esp_coverage_test_plan.rst
> @@ -0,0 +1,1458 @@
> +.. Copyright (c) <2020>, Intel Corporation
> + All rights reserved.
> +
> + Redistribution and use in source and binary forms, with or without
> + modification, are permitted provided that the following conditions
> + are met:
> +
> + - Redistributions of source code must retain the above copyright
> + notice, this list of conditions and the following disclaimer.
> +
> + - Redistributions in binary form must reproduce the above copyright
> + notice, this list of conditions and the following disclaimer in
> + the documentation and/or other materials provided with the
> + distribution.
> +
> + - Neither the name of Intel Corporation nor the names of its
> + contributors may be used to endorse or promote products derived
> + from this software without specific prior written permission.
> +
> + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
> CONTRIBUTORS
> + "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
> + LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
> FITNESS
> + FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
> + COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
> INDIRECT,
> + INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> + (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
> GOODS OR
> + SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
> + HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
> CONTRACT,
> + STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
> + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
> ADVISED
> + OF THE POSSIBILITY OF SUCH DAMAGE.
> +
> +================================
> +test coverage for L2TPv3 and ESP
> +================================
> +
> +Description
> +===========
> +For each protocol, below is a list of standard features supported by the
> Columbiaville hardware and the impact on the feature for each protocol.
> +Some features are supported in a limited manner as stated below.
> +
> +IPSec(ESP):
> +L2 Tag offloads
> +----L2 Tag Stripping - Yes
> +----L2 Tag insertion - Yes
> +Checksum offloads - Yes
> +----Only outer layer 3 checksum for IP+ESP and IP+AH packets
> +----Outer layer 3 and 4 checksum for ESP over UDP packets
> +Manageability - No
> +----Packets must be excluded
> +RDMA - No
> +----Packets must be excluded
> +DCB
> +----Priority Flow Control - No
> +
> +L2TPv3:
> +L2 Tag offloads
> +----L2 Tag Stripping - Yes
> +----L2 Tag insertion - Yes
> +Checksum offloads - Yes
> +----Only outer layer 3
> +Manageability - No
> +----Packets must be excluded
> +RDMA - No
> +----Packets must be excluded
> +DCB
> +----Priority Flow Control - No
> +
> +this test plan is designed to check above offloads in L2TPv3 and ESP.
> +and CVL can't support tx checksum in vector path now, so only test the rx
> checksum offload.
> +
> +
> +Prerequisites
> +=============
> +
> +1. create a vf from a pf::
> +
> + echo 1 > /sys/bus/pci/devices/0000\:af\:00.0/sriov_numvfs
> + ip link set enp175s0f0 vf 0 mac 00:11:22:33:44:55
> +
> +2. bind vf to vfio-pci::
> +
> + ./usertools/dpdk-devbind.py -b vfio-pci af:01.0
> +
> +
> +Test Case 1: test MAC_IPV4_L2TPv3 HW checksum offload
> +=====================================================
> +
> +1. DUT enable rx checksum with "--enable-rx-cksum" when start testpmd::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -n 4 -w af:01.0 -- -i --enable-
> rx-cksum
> +
> +2. DUT setup csum forwarding mode::
> +
> + testpmd> port stop all
> + testpmd> csum set ip hw 0
> + testpmd> port start all
> + testpmd> set fwd csum
> + testpmd> set verbose 1
> + testpmd> start
> +
> +3. Tester send MAC_IPV4_L2TPv3 packets with correct checksum::
> +
> + sendp([Ether(dst="00:11:22:33:44:55")/IP(src="192.168.0.3",
> proto=115)/L2TP('\x00\x00\x00\x11')/Raw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the packets are correctly received with
> "PKT_RX_IP_CKSUM_GOOD" by DUT::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x0800 - length=518
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV4 -
> l2_len=14 - l3_len=20 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x22848a2680, pkt_len=518, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=115 l4_len=0
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 0 Bad-l4csum: 0 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +5. Tester send MAC_IPV4_L2TPv3 packets with incorrect checksum::
> +
> + sendp([Ether(dst="00:11:22:33:44:55")/IP(src="192.168.0.3",
> proto=115,chksum=0x123)/L2TP('\x00\x00\x00\x11')/Raw('x'*480)],
> iface="enp134s0f0")
> +
> +6. DUT check the packets are correctly received by DUT and report the
> checksum error::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x0800 - length=518
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV4 -
> l2_len=14 - l3_len=20 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2284780c40, pkt_len=518, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=115 l4_len=0
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 1 Bad-l4csum: 0 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +
> +Test Case 2: test MAC_IPV4_ESP HW checksum offload
> +==================================================
> +
> +1. DUT enable rx checksum with "--enable-rx-cksum" when start testpmd,
> setup csum forwarding mode::
> +
> + ./x86_64-native-linuxapp-gcc/app/testpmd -n 4 -w af:01.0 -- -i --enable-
> rx-cksum
> +
> +2. DUT setup csum forwarding mode::
> +
> + testpmd> port stop all
> + testpmd> csum set ip hw 0
> + testpmd> port start all
> + testpmd> set fwd csum
> + testpmd> set verbose 1
> + testpmd> start
> +
> +3. Tester send MAC_IPV4_ESP packets with correct checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(proto=50)/ESP(spi=11)/Raw('x'*48
> 0)], iface="enp134s0f0")
> +
> +4. DUT check the packets are correctly received with
> "PKT_RX_IP_CKSUM_GOOD" by DUT::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x0800 - length=522
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV4 -
> l2_len=14 - l3_len=20 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x22848a2fc0, pkt_len=522, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=50 l4_len=0
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 0 Bad-l4csum: 0 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +5. Tester send MAC_IPV4_ESP packets with incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(proto=50,chksum=0x123)/ESP(spi=
> 11)/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the packets are correctly received by DUT and report the
> checksum error::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x0800 - length=522
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV4 -
> l2_len=14 - l3_len=20 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2284781580, pkt_len=522, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=50 l4_len=0
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 1 Bad-l4csum: 0 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +
> +Test Case 3: test MAC_IPV4_AH HW checksum offload
> +=================================================
> +
> +1. DUT enable rx checksum with "--enable-rx-cksum" when start testpmd,
> setup csum forwarding mode::
> +
> +2. DUT setup csum forwarding mode::
> +
> + testpmd> port stop all
> + testpmd> csum set ip hw 0
> + testpmd> port start all
> + testpmd> set fwd csum
> + testpmd> set verbose 1
> + testpmd> start
> +
> +3. Tester send MAC_IPV4_AH packets with correct checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(proto=51)/AH(spi=11)/Raw('x'*480
> )], iface="enp134s0f0")
> +
> +4. DUT check the packets are correctly received with
> "PKT_RX_IP_CKSUM_GOOD" by DUT::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x0800 - length=526
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV4 -
> l2_len=14 - l3_len=20 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2284782800, pkt_len=526, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=51 l4_len=0
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 0 Bad-l4csum: 0 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +5. Tester send MAC_IPV4_AH packets with incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(proto=51,chksum=0x123)/AH(spi=
> 11)/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the packets are correctly received by DUT and report the
> checksum error::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x0800 - length=526
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV4 -
> l2_len=14 - l3_len=20 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2284783140, pkt_len=526, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=51 l4_len=0
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 1 Bad-l4csum: 0 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +
> +Test Case 4: test MAC_IPV4_NAT-T-ESP HW checksum offload
> +========================================================
> +
> +1. DUT enable rx checksum with "--enable-rx-cksum" when start testpmd,
> setup csum forwarding mode::
> +
> +2. DUT setup csum forwarding mode::
> +
> + testpmd> port stop all
> + testpmd> csum set ip hw 0
> + testpmd> csum set udp hw 0
> + testpmd> port start all
> + testpmd> set fwd csum
> + testpmd> set verbose 1
> + testpmd> start
> +
> +3. Tester send MAC_IPV4_NAT-T-ESP pkt with correct IPv4 checksum and
> correct UDP checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP()/UDP(dport=4500)/ESP(spi=11)/R
> aw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the packets are correctly received with
> "PKT_RX_L4_CKSUM_GOOD" and "PKT_RX_IP_CKSUM_GOOD" by DUT::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x0800 - length=530
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV4
> L4_UDP - l2_len=14 - l3_len=20 - l4_len=8 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x22847843c0, pkt_len=530, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=17 l4_len=8
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=8
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 0 Bad-l4csum: 0 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +5. Tester send MAC_IPV4_NAT-T-ESP pkt with correct IPv4 checksum and
> incorrect UDP checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP()/UDP(dport=4500,chksum=0x123)
> /ESP(spi=11)/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the packets are correctly received with
> "PKT_RX_IP_CKSUM_GOOD" and report UDP checksum error by DUT::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x0800 - length=530
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV4
> L4_UDP - l2_len=14 - l3_len=20 - l4_len=8 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_BAD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2284784d00, pkt_len=530, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=17 l4_len=8
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_BAD PKT_RX_IP_CKSUM_GOOD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=8
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 0 Bad-l4csum: 1 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +7. Tester send MAC_IPV4_NAT-T-ESP pkt with incorrect IPv4 checksum and
> correct UDP checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(chksum=0x123)/UDP(dport=4500)/
> ESP(spi=11)/Raw('x'*480)], iface="enp134s0f0")
> +
> +8. DUT check the packets are correctly received with
> "PKT_RX_L4_CKSUM_GOOD" and report IP checksum error by DUT::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x0800 - length=530
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV4
> L4_UDP - l2_len=14 - l3_len=20 - l4_len=8 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x22848a1400, pkt_len=530, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=17 l4_len=8
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=8
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 1 Bad-l4csum: 0 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +9. Tester send MAC_IPV4_NAT-T-ESP pkt with incorrect IPv4 checksum and
> incorrect UDP checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(chksum=0x123)/UDP(dport=4500,c
> hksum=0x123)/ESP(spi=11)/Raw('x'*480)], iface="enp134s0f0")
> +
> +10. DUT check the packets are correctly received by DUT and report the
> checksum error::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x0800 - length=530
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV4
> L4_UDP - l2_len=14 - l3_len=20 - l4_len=8 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_BAD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x22848a0ac0, pkt_len=530, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=17 l4_len=8
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_BAD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=8
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 1 Bad-l4csum: 1 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +
> +Test Case 5: test MAC_IPV6_NAT-T-ESP HW checksum offload
> +========================================================
> +
> +1. DUT enable rx checksum with "--enable-rx-cksum" when start testpmd,
> setup csum forwarding mode::
> +
> +2. DUT setup csum forwarding mode::
> +
> + testpmd> port stop all
> + testpmd> csum set udp hw 0
> + testpmd> port start all
> + testpmd> set fwd csum
> + testpmd> set verbose 1
> + testpmd> start
> +
> +3. Tester send MAC_IPV6_NAT-T-ESP packets with correct checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IPv6()/UDP(dport=4500)/ESP(spi=11)/
> Raw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the packets are correctly received with
> "PKT_RX_L4_CKSUM_GOOD" by DUT::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x86dd - length=550
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV6
> L4_UDP - l2_len=14 - l3_len=40 - l4_len=8 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x228489e5c0, pkt_len=550, nb_segs=1:
> + rx: l2_len=14 ethertype=86dd l3_len=40 l4_proto=17 l4_len=8
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=40 m->l4_len=8
> + tx: flags=PKT_TX_L4_NO_CKSUM PKT_TX_IPV6
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 0 Bad-l4csum: 0 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +5. Tester send MAC_IPV6_NAT-T-ESP packets with incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IPv6()/UDP(dport=4500,chksum=0x12
> 3)/ESP(spi=11)/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the packets are correctly received by DUT and report the
> checksum error::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=00:00:00:00:00:00 - dst=00:11:22:33:44:55 - type=0x86dd - length=550
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER L3_IPV6
> L4_UDP - l2_len=14 - l3_len=40 - l4_len=8 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_BAD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x228489dc80, pkt_len=550, nb_segs=1:
> + rx: l2_len=14 ethertype=86dd l3_len=40 l4_proto=17 l4_len=8
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_BAD PKT_RX_IP_CKSUM_GOOD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=40 m->l4_len=8
> + tx: flags=PKT_TX_L4_NO_CKSUM PKT_TX_IPV6
> + stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + Bad-ipcsum: 0 Bad-l4csum: 1 Bad-outer-l4csum: 0
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 1 RX-dropped: 0 RX-total: 1
> + TX-packets: 1 TX-dropped: 0 TX-total: 1
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +
> +Test Case 6: test MAC_IPV4_L2TPv3 l2 tag
> +========================================
> +
> +subcase 1: vlan stripping
> +-------------------------
> +1. DUT set vlan filter on and enable the vlan receipt::
> +
> + testpmd > vlan set filter on 0
> + testpmd > set fwd mac
> + testpmd > set verbose 1
> + testpmd > rx_vlan add 1 0
> +
> +2. DUT enable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip off 0
> + testpmd > start
> +
> +3. Tester send MAC_IPV4_L2TPv3 pkt with vlan tag identifier
> 1(ether/vlan/ip/l2tp)::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=115)/L2TP('\
> x00\x00\x00\x11')/Raw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the pkt is recieved and fwd with vlan tag 1::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x8100 - length=522
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - sw ptype: L2_ETHER_VLAN
> L3_IPV4 - l2_len=18 - l3_len=20 - Receive queue=0x0
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> +
> + tcpdump -i enp134s0f0 -Q in -e -n -v -x
> + 15:19:26.315127 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 522: vlan 1, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 1, offset 0,
> flags [none], proto unknown (115), length 504)
> + 127.0.0.1 > 127.0.0.1: ip-proto-115 484
> +
> +5. Tester send MAC_IPV4_L2TPv3 pkt with vlan tag identifier 2::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=2)/IP(proto=115)/L2TP('\
> x00\x00\x00\x11')/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the pkt is not recieved::
> +
> + testpmd> stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 0 RX-dropped: 0 RX-total: 0
> + TX-packets: 0 TX-dropped: 0 TX-total: 0
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 0 RX-dropped: 0 RX-total: 0
> + TX-packets: 0 TX-dropped: 0 TX-total: 0
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +7. DUT disable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip on 0
> + testpmd > start
> +
> +8. Tester send MAC_IPV4_L2TPv3 pkt with vlan tag identifier 1::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=115)/L2TP('\
> x00\x00\x00\x11')/Raw('x'*480)], iface="enp134s0f0")
> +
> +9. DUT check the pkt is recieved and fwd without vlan tag identifier 1::
> +
> + testpmd> port 0/queue 0: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x0800 - length=518
> - nb_segs=1 - RSS hash=0x0 - RSS queue=0x0 - VLAN tci=0x1 - sw ptype:
> L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x0
> + ol_flags: PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_GOOD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> +
> + 15:20:43.803087 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv4
> (0x0800), length 518: (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto
> unknown (115), length 504)
> + 127.0.0.1 > 127.0.0.1: ip-proto-115 484
> +
> +subcase 2: vlan insertion
> +-------------------------
> +
> +1. Add tx vlan offload on port 0, take care the first param is port::
> +
> + testpmd> vlan set strip off 0
> + testpmd> port stop all
> + testpmd> tx_vlan set 0 1
> + testpmd> vlan set filter on 0
> + testpmd> rx_vlan add 1 0
> + testpmd> port start all
> + testpmd> start
> +
> +2. Tester send MAC_IPV4_L2TPv3 packets without vlan to port 0::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(proto=115)/L2TP('\x00\x00\x00\x1
> 1')/Raw('x'*480)], iface="enp134s0f0")
> +
> +3. Tester check recieved the pkt with vlan tag identifier 1::
> +
> + 16:08:17.119129 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 526: vlan 1, p 0, ethertype 802.1Q, vlan 1, p 0, ethertype
> IPv4, (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto unknown (115), length
> 504)
> + 127.0.0.1 > 127.0.0.1: ip-proto-115 484
> +
> +
> +Test Case 7: test MAC_IPV6_L2TPv3 l2 tag
> +========================================
> +
> +subcase 1: vlan stripping
> +-------------------------
> +1. DUT set vlan filter on and enable the vlan receipt::
> +
> + testpmd > vlan set filter on 0
> + testpmd > set fwd mac
> + testpmd > set verbose 1
> + testpmd > rx_vlan add 1 0
> +
> +2. DUT enable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip off 0
> + testpmd > start
> +
> +3. Tester send MAC_IPV6_L2TPv3 pkt with vlan tag identifier
> 1(ether/vlan/ip/l2tp)::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IPv6(nh=115)/L2TP('\x
> 00\x00\x00\x11')/Raw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the pkt is fwd with vlan tag 1::
> +
> + 16:10:25.899116 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 542: vlan 1, p 0, ethertype IPv6, (hlim 64, next-header
> unknown (115) payload length: 484) ::1 > ::1: ip-proto-115 484
> +
> +5. Tester send MAC_IPV6_L2TPv3 pkt with vlan tag identifier 2::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=2)/IPv6(nh=115)/L2TP('\x
> 00\x00\x00\x11')/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the pkt is not recieved::
> +
> + testpmd> stop
> + Telling cores to stop...
> + Waiting for lcores to finish...
> +
> + ---------------------- Forward statistics for port 0 ----------------------
> + RX-packets: 0 RX-dropped: 0 RX-total: 0
> + TX-packets: 0 TX-dropped: 0 TX-total: 0
> + ----------------------------------------------------------------------------
> +
> + +++++++++++++++ Accumulated forward statistics for all
> ports+++++++++++++++
> + RX-packets: 0 RX-dropped: 0 RX-total: 0
> + TX-packets: 0 TX-dropped: 0 TX-total: 0
> +
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> ++++++++++++
> +
> +7. DUT disable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip on 0
> + testpmd > start
> +
> +8. Tester send MAC_IPV6_L2TPv3 pkt with vlan tag identifier 1::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IPv6(nh=115)/L2TP('\x
> 00\x00\x00\x11')/Raw('x'*480)], iface="enp134s0f0")
> +
> +9. DUT check the pkt is fwd without vlan tag identifier 1::
> +
> + 16:13:20.231049 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv6
> (0x86dd), length 538: (hlim 64, next-header unknown (115) payload length:
> 484) ::1 > ::1: ip-proto-115 484
> +
> +subcase 2: vlan insertion
> +-------------------------
> +
> +1. Add tx vlan offload on port 0, take care the first param is port::
> +
> + testpmd> vlan set strip off 0
> + testpmd> port stop all
> + testpmd> tx_vlan set 0 1
> + testpmd> vlan set filter on 0
> + testpmd> rx_vlan add 1 0
> + testpmd> port start all
> + testpmd> start
> +
> +2. Tester send MAC_IPV6_L2TPv3 packets without vlan to port 0::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IPv6(nh=115)/L2TP('\x00\x00\x00\x1
> 1')/Raw('x'*480)], iface="enp134s0f0")
> +
> +3. Tester check recieved the pkt with vlan tag identifier 1::
> +
> + 16:15:35.311109 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 546: vlan 1, p 0, ethertype 802.1Q, vlan 1, p 0, ethertype
> IPv6, (hlim 64, next-header unknown (115) payload length: 484) ::1 > ::1: ip-
> proto-115 484
> +
> +
> +Test Case 8: test MAC_IPV4_ESP l2 tag
> +=====================================
> +
> +subcase 1: vlan stripping
> +-------------------------
> +1. DUT set vlan filter on and enable the vlan receipt::
> +
> + testpmd > vlan set filter on 0
> + testpmd > set fwd mac
> + testpmd > set verbose 1
> + testpmd > rx_vlan add 1 0
> +
> +2. DUT enable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip off 0
> + testpmd > start
> +
> +3. Tester send MAC_IPV4_ESP pkt with vlan tag identifier
> 1(ether/vlan/ip/esp)::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=50)/ESP(spi=
> 1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the pkt is fwd with vlan tag 1::
> +
> + 16:19:22.039132 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 526: vlan 1, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 1, offset 0,
> flags [none], proto ESP (50), length 508)
> + 127.0.0.1 > 127.0.0.1: ESP(spi=0x00000001,seq=0x0), length 488
> +
> +5. Tester send MAC_IPV4_ESP pkt with vlan tag identifier 2::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=2)/IP(proto=50)/ESP(spi=
> 1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the pkt is not recieved::
> +
> +7. DUT disable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip on 0
> + testpmd > start
> +
> +8. Tester send MAC_IPV4_ESP pkt with vlan tag identifier 1::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=50)/ESP(spi=
> 1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +9. DUT check the pkt is fwd without vlan tag identifier 1::
> +
> + 16:20:49.995057 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv4
> (0x0800), length 522: (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto ESP
> (50), length 508)
> + 127.0.0.1 > 127.0.0.1: ESP(spi=0x00000001,seq=0x0), length 488
> +
> +subcase 2: vlan insertion
> +-------------------------
> +
> +1. Add tx vlan offload on port 0, take care the first param is port::
> +
> + testpmd> vlan set strip off 0
> + testpmd> port stop all
> + testpmd> tx_vlan set 0 1
> + testpmd> vlan set filter on 0
> + testpmd> rx_vlan add 1 0
> + testpmd> port start all
> + testpmd> start
> +
> +2. Tester send MAC_IPV4_ESP packets without vlan to port 0::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(proto=50)/ESP(spi=1)/Raw('x'*480)
> ], iface="enp134s0f0")
> +
> +3. Tester check recieved the pkt with vlan tag identifier 1::
> +
> + 16:23:08.631125 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 530: vlan 1, p 0, ethertype 802.1Q, vlan 1, p 0, ethertype
> IPv4, (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto ESP (50), length 508)
> + 127.0.0.1 > 127.0.0.1: ESP(spi=0x00000001,seq=0x0), length 488
> +
> +
> +Test Case 9: test MAC_IPV6_ESP l2 tag
> +=====================================
> +
> +subcase 1: vlan stripping
> +-------------------------
> +1. DUT set vlan filter on and enable the vlan receipt::
> +
> + testpmd > vlan set filter on 0
> + testpmd > set fwd mac
> + testpmd > set verbose 1
> + testpmd > rx_vlan add 1 0
> +
> +2. DUT enable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip off 0
> + testpmd > start
> +
> +3. Tester send MAC_IPV6_ESP pkt with vlan tag identifier
> 1(ether/vlan/ip/esp)::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IPv6(nh=50)/ESP(spi=
> 1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the pkt is fwd with vlan tag 1::
> +
> + 16:25:49.075114 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 546: vlan 1, p 0, ethertype IPv6, (hlim 64, next-header ESP
> (50) payload length: 488) ::1 > ::1: ESP(spi=0x00000001,seq=0x0), length 488
> +
> +5. Tester send MAC_IPV6_ESP pkt with vlan tag identifier 2::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=2)/IPv6(nh=50)/ESP(spi=
> 1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the pkt is not recieved::
> +
> +7. DUT disable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip on 0
> + testpmd > start
> +
> +8. Tester send MAC_IPV6_ESP pkt with vlan tag identifier 1::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IPv6(nh=50)/ESP(spi=
> 1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +9. DUT check the pkt is fwd without vlan tag identifier 1::
> +
> + 16:26:40.279043 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv6
> (0x86dd), length 542: (hlim 64, next-header ESP (50) payload length:
> 488) ::1 > ::1: ESP(spi=0x00000001,seq=0x0), length 488
> +
> +subcase 2: vlan insertion
> +-------------------------
> +
> +1. Add tx vlan offload on port 0, take care the first param is port::
> +
> + testpmd> vlan set strip off 0
> + testpmd> port stop all
> + testpmd> tx_vlan set 0 1
> + testpmd> vlan set filter on 0
> + testpmd> rx_vlan add 1 0
> + testpmd> port start all
> + testpmd> start
> +
> +2. Tester send MAC_IPV6_ESP packets without vlan to port 0::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IPv6(nh=50)/ESP(spi=1)/Raw('x'*480)
> ], iface="enp134s0f0")
> +
> +3. Tester check recieved the pkt with vlan tag identifier 1::
> +
> + 16:28:30.323047 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 550: vlan 1, p 0, ethertype 802.1Q, vlan 1, p 0, ethertype
> IPv6, (hlim 64, next-header ESP (50) payload length: 488) ::1 > ::1:
> ESP(spi=0x00000001,seq=0x0), length 488
> +
> +
> +Test Case 10: test MAC_IPV4_AH l2 tag
> +=====================================
> +
> +subcase 1: vlan stripping
> +-------------------------
> +1. DUT set vlan filter on and enable the vlan receipt::
> +
> + testpmd > vlan set filter on 0
> + testpmd > set fwd mac
> + testpmd > set verbose 1
> + testpmd > rx_vlan add 1 0
> +
> +2. DUT enable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip off 0
> + testpmd > start
> +
> +3. Tester send MAC_IPV4_AH pkt with vlan tag identifier
> 1(ether/vlan/ip/ahA)::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=51)/AH(spi=
> 1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the pkt is fwd with vlan tag 1::
> +
> + 16:30:56.899138 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 530: vlan 1, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 1, offset 0,
> flags [none], proto AH (51), length 512)
> + 127.0.0.1 > 127.0.0.1: AH(spi=0x00000001,sumlen=0,seq=0x0): ip-proto-0
> 484
> +
> +5. Tester send MAC_IPV4_AH pkt with vlan tag identifier 2::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=2)/IP(proto=51)/AH(spi=
> 1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the pkt is not recieved::
> +
> +7. DUT disable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip on 0
> + testpmd > start
> +
> +8. Tester send MAC_IPV4_AH pkt with vlan tag identifier 1::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=51)/AH(spi=
> 1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +9. DUT check the pkt is fwd without vlan tag identifier 1::
> +
> + 16:34:32.599097 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv4
> (0x0800), length 526: (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto AH (51),
> length 512)
> + 127.0.0.1 > 127.0.0.1: AH(spi=0x00000001,sumlen=0,seq=0x0): ip-proto-0
> 484
> +
> +
> +subcase 2: vlan insertion
> +-------------------------
> +
> +1. Add tx vlan offload on port 0, take care the first param is port::
> +
> + testpmd> vlan set strip off 0
> + testpmd> port stop all
> + testpmd> tx_vlan set 0 1
> + testpmd> vlan set filter on 0
> + testpmd> rx_vlan add 1 0
> + testpmd> port start all
> + testpmd> start
> +
> +2. Tester send MAC_IPV4_AH packets without vlan to port 0::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(proto=51)/AH(spi=1)/Raw('x'*480)
> ], iface="enp134s0f0")
> +
> +3. Tester check recieved the pkt with vlan tag identifier 1::
> +
> + 16:37:21.783066 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 534: vlan 1, p 0, ethertype 802.1Q, vlan 1, p 0, ethertype
> IPv4, (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto AH (51), length 512)
> + 127.0.0.1 > 127.0.0.1: AH(spi=0x00000001,sumlen=0,seq=0x0): ip-proto-0
> 484
> +
> +
> +Test Case 11: test MAC_IPV6_AH l2 tag
> +=====================================
> +
> +subcase 1: vlan stripping
> +-------------------------
> +1. DUT set vlan filter on and enable the vlan receipt::
> +
> + testpmd > vlan set filter on 0
> + testpmd > set fwd mac
> + testpmd > set verbose 1
> + testpmd > rx_vlan add 1 0
> +
> +2. DUT enable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip off 0
> + testpmd > start
> +
> +3. Tester send MAC_IPV6_AH pkt with vlan tag identifier
> 1(ether/vlan/ip/ah)::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IPv6(nh=51)/AH(spi=1
> )/Raw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the pkt is fwd with vlan tag 1::
> +
> + 16:32:11.519239 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 550: vlan 1, p 0, ethertype IPv6, (hlim 64, next-header AH
> (51) payload length: 492) ::1 > ::1: AH(spi=0x00000001,sumlen=0,seq=0x0):
> HBH (pad1)(pad1)[trunc] [|HBH]
> +
> +5. Tester send MAC_IPV6_AH pkt with vlan tag identifier 2::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=2)/IPv6(nh=51)/AH(spi=1
> )/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the pkt is not recieved::
> +
> +7. DUT disable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip on 0
> + testpmd > start
> +
> +8. Tester send MAC_IPV6_AH pkt with vlan tag identifier 1::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IPv6(nh=51)/AH(spi=1
> )/Raw('x'*480)], iface="enp134s0f0")
> +
> +9. DUT check the pkt is fwd without vlan tag identifier 1::
> +
> + 16:35:27.395058 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv6
> (0x86dd), length 546: (hlim 64, next-header AH (51) payload length:
> 492) ::1 > ::1: AH(spi=0x00000001,sumlen=0,seq=0x0): HBH
> (pad1)(pad1)[trunc] [|HBH]
> +
> +
> +subcase 2: vlan insertion
> +-------------------------
> +
> +1. Add tx vlan offload on port 0, take care the first param is port::
> +
> + testpmd> vlan set strip off 0
> + testpmd> port stop all
> + testpmd> tx_vlan set 0 1
> + testpmd> vlan set filter on 0
> + testpmd> rx_vlan add 1 0
> + testpmd> port start all
> + testpmd> start
> +
> +2. Tester send MAC_IPV6_AH packets without vlan to port 0::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IPv6(nh=51)/AH(spi=1)/Raw('x'*480)],
> iface="enp134s0f0")
> +
> +3. Tester check recieved the pkt with vlan tag identifier 1::
> +
> + 16:38:02.311042 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 554: vlan 1, p 0, ethertype 802.1Q, vlan 1, p 0, ethertype
> IPv6, (hlim 64, next-header AH (51) payload length: 492) ::1 > ::1:
> AH(spi=0x00000001,sumlen=0,seq=0x0): HBH (pad1)(pad1)[trunc] [|HBH]
> +
> +
> +Test Case 12: test MAC_IPV4_NAT-T-ESP l2 tag
> +============================================
> +
> +subcase 1: vlan stripping
> +-------------------------
> +1. DUT set vlan filter on and enable the vlan receipt::
> +
> + testpmd > vlan set filter on 0
> + testpmd > set fwd mac
> + testpmd > set verbose 1
> + testpmd > rx_vlan add 1 0
> +
> +2. DUT enable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip off 0
> + testpmd > start
> +
> +3. Tester send MAC_IPV4_NAT-T-ESP pkt with vlan tag identifier
> 1(ether/vlan/ip/udp/esp)::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP()/UDP(dport=4500)
> /ESP(spi=1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the pkt is fwd with vlan tag 1::
> +
> + 16:43:18.351118 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 534: vlan 1, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 1, offset 0,
> flags [none], proto UDP (17), length 516)
> + 127.0.0.1.4500 > 127.0.0.1.4500: UDP-encap:
> ESP(spi=0x00000001,seq=0x0), length 488
> +
> +5. Tester send MAC_IPV4_NAT-T-ESP pkt with vlan tag identifier 2::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=2)/IP()/UDP(dport=4500)
> /ESP(spi=1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the pkt is not recieved::
> +
> +7. DUT disable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip on 0
> + testpmd > start
> +
> +8. Tester send MAC_IPV4_NAT-T-ESP pkt with vlan tag identifier 1::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP()/UDP(dport=4500)
> /ESP(spi=1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +9. DUT check the pkt is recieved without vlan tag identifier 1::
> +
> + 16:46:50.015123 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv4
> (0x0800), length 530: (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto UDP
> (17), length 516)
> + 127.0.0.1.4500 > 127.0.0.1.4500: UDP-encap:
> ESP(spi=0x00000001,seq=0x0), length 488
> +
> +subcase 2: vlan insertion
> +-------------------------
> +
> +1. Add tx vlan offload on port 0, take care the first param is port::
> +
> + testpmd> vlan set strip off 0
> + testpmd> port stop all
> + testpmd> tx_vlan set 0 1
> + testpmd> vlan set filter on 0
> + testpmd> rx_vlan add 1 0
> + testpmd> port start all
> + testpmd> start
> +
> +2. Tester send MAC_IPV4_NAT-T-ESP packets without vlan to port 0::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP()/UDP(dport=4500)/ESP(spi=1)/Ra
> w('x'*480)], iface="enp134s0f0")
> +
> +3. Tester check recieved the pkt with vlan tag identifier 1::
> +
> + 16:49:41.875196 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 538: vlan 1, p 0, ethertype 802.1Q, vlan 1, p 0, ethertype
> IPv4, (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto UDP (17), length 516)
> + 127.0.0.1.4500 > 127.0.0.1.4500: UDP-encap:
> ESP(spi=0x00000001,seq=0x0), length 488
> +
> +
> +Test Case 13: test MAC_IPV6_NAT-T-ESP l2 tag
> +============================================
> +
> +subcase 1: vlan stripping
> +-------------------------
> +1. DUT set vlan filter on and enable the vlan receipt::
> +
> + testpmd > vlan set filter on 0
> + testpmd > set fwd mac
> + testpmd > set verbose 1
> + testpmd > rx_vlan add 1 0
> +
> +2. DUT enable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip off 0
> + testpmd > start
> +
> +3. Tester send MAC_IPV6_NAT-T-ESP pkt with vlan tag identifier
> 1(ether/vlan/ip/udp/esp)::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IPv6()/UDP(dport=450
> 0)/ESP(spi=1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +4. DUT check the pkt is fwd with vlan tag 1::
> +
> + 16:44:13.959467 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 554: vlan 1, p 0, ethertype IPv6, (hlim 64, next-header UDP
> (17) payload length: 496) ::1.4500 > ::1.4500: [udp sum ok] UDP-encap:
> ESP(spi=0x00000001,seq=0x0), length 488
> +
> +5. Tester send MAC_IPV6_NAT-T-ESP pkt with vlan tag identifier 2::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=2)/IPv6()/UDP(dport=450
> 0)/ESP(spi=1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the pkt is not recieved::
> +
> +7. DUT disable the vlan header stripping with vlan tag identifier 1::
> +
> + testpmd > vlan set strip on 0
> + testpmd > start
> +
> +8. Tester send MAC_IPV6_NAT-T-ESP pkt with vlan tag identifier 1::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IPv6()/UDP(dport=450
> 0)/ESP(spi=1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +9. DUT check the pkt is recieved without vlan tag identifier 1::
> +
> + 16:47:30.747658 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv6
> (0x86dd), length 550: (hlim 64, next-header UDP (17) payload length:
> 496) ::1.4500 > ::1.4500: [udp sum ok] UDP-encap:
> ESP(spi=0x00000001,seq=0x0), length 488
> +
> +subcase 2: vlan insertion
> +-------------------------
> +
> +1. Add tx vlan offload on port 0, take care the first param is port::
> +
> + testpmd> vlan set strip off 0
> + testpmd> port stop all
> + testpmd> tx_vlan set 0 1
> + testpmd> vlan set filter on 0
> + testpmd> rx_vlan add 1 0
> + testpmd> port start all
> + testpmd> start
> +
> +2. Tester send MAC_IPV4_NAT-T-ESP packets without vlan to port 0::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IPv6()/UDP(dport=4500)/ESP(spi=1)/R
> aw('x'*480)], iface="enp134s0f0")
> +
> +3. Tester check recieved the pkt with vlan tag identifier 1::
> +
> + 16:50:29.791349 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype 802.1Q
> (0x8100), length 558: vlan 1, p 0, ethertype 802.1Q, vlan 1, p 0, ethertype
> IPv6, (hlim 64, next-header UDP (17) payload length: 496) ::1.4500 > ::1.4500:
> [udp sum ok] UDP-encap: ESP(spi=0x00000001,seq=0x0), length 488
> +
> +
> +Test Case 14: MAC_IPV4_L2TPv3 vlan strip on + HW checksum offload check
> +===============================================================
> ========
> +
> +The pre-steps are as l2tp_esp_iavf_test_plan.
> +
> +1. ./x86_64-native-linuxapp-gcc/app/testpmd -l 6-9 -n 4 -w af:01.0 -- -i --
> rxq=16 --txq=16 --portmask=0x1 --nb-cores=2 --enable-rx-cksum
> +
> +2. DUT create fdir rules for MAC_IPV4_L2TPv3 with queue index and mark::
> +
> + flow create 0 ingress pattern eth / ipv4 / l2tpv3oip session_id is 1 / end
> actions queue index 1 / mark id 4 / end
> + flow create 0 ingress pattern eth / ipv4 / l2tpv3oip session_id is 2 / end
> actions queue index 2 / mark id 3 / end
> + flow create 0 ingress pattern eth / ipv4 / l2tpv3oip session_id is 3 / end
> actions queue index 3 / mark id 2 / end
> + flow create 0 ingress pattern eth / ipv4 / l2tpv3oip session_id is 4 / end
> actions queue index 4 / mark id 1 / end
> +
> +3. Enable vlan filter and receipt of VLAN packets with VLAN Tag Identifier 1
> on port 0, Enable vlan strip on VF0::
> +
> + testpmd> vlan set filter on 0
> + testpmd> rx_vlan add 1 0
> + testpmd> vlan set strip on 0
> + testpmd> set verbose 1
> +
> +4. enable hw checksum::
> +
> + testpmd> set fwd csum
> + Set csum packet forwarding mode
> + testpmd> port stop all
> + testpmd> csum set ip hw 0
> + testpmd> csum set udp hw 0
> + testpmd> port start all
> + testpmd> start
> +
> +5. Tester send matched packets with VLAN tag "1" and incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=115,chksum
> =0x123)/L2TP('\x00\x00\x00\x01')/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the packets are distributed to expected queue with mark id
> and fwd without VLAN tag "1", and report the checksum error::
> +
> + testpmd> port 0/queue 1: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x0800 - length=518
> - nb_segs=1 - RSS hash=0x828dafbf - RSS queue=0x1 - VLAN tci=0x1 - sw
> ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x1
> + ol_flags: PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2268c09840, pkt_len=518, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=115 l4_len=0
> flags=PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> + 15:20:43.803087 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv4
> (0x0800), length 518: (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto
> unknown (115), length 504)
> + 127.0.0.1 > 127.0.0.1: ip-proto-115 484
> +
> +7. Tester send mismatched packets with VLAN tag "1" and incorrect
> checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=115,chksum
> =0x123)/L2TP('\x00\x00\x00\x11')/Raw('x'*480)], iface="enp134s0f0")
> +
> +8. DUT check the packets are not distributed to expected queue without
> mark id and fwd without VLAN tag "1", and report the checksum error::
> +
> + port 0/queue 15: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x0800 - length=518
> - nb_segs=1 - RSS hash=0x828dafbf - RSS queue=0xf - VLAN tci=0x1 - sw ptype:
> L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0xf
> + ol_flags: PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2269cba700, pkt_len=518, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=115 l4_len=0
> flags=PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> + 15:20:43.803087 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv4
> (0x0800), length 518: (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto
> unknown (115), length 504)
> + 127.0.0.1 > 127.0.0.1: ip-proto-115 484
> +
> +9. DUT verify rule can be listed and destroyed::
> +
> + testpmd> flow list 0
> + ID Group Prio Attr Rule
> + 0 0 0 i-- ETH IPV4 L2TPV3OIP => QUEUE MARK
> + 1 0 0 i-- ETH IPV4 L2TPV3OIP => QUEUE MARK
> + 2 0 0 i-- ETH IPV4 L2TPV3OIP => QUEUE MARK
> + 3 0 0 i-- ETH IPV4 L2TPV3OIP => QUEUE MARK
> + testpmd> flow destroy 0 rule 0
> +
> +10. Tester send matched packets with VLAN tag "1" and incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=115,chksum
> =0x123)/L2TP('\x00\x00\x00\x01')/Raw('x'*480)], iface="enp134s0f0")
> +
> +11.DUT check the packets are not distributed to expected queue without
> mark id and and without VLAN tag "1", and report the checksum error::
> +
> + testpmd> port 0/queue 15: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x0800 - length=518
> - nb_segs=1 - RSS hash=0x828dafbf - RSS queue=0xf - VLAN tci=0x1 - sw ptype:
> L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0xf
> + ol_flags: PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2269cb9dc0, pkt_len=518, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=115 l4_len=0
> flags=PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> + 15:20:43.803087 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv4
> (0x0800), length 518: (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto
> unknown (115), length 504)
> + 127.0.0.1 > 127.0.0.1: ip-proto-115 484
> +
> +
> +Test Case 15: MAC_IPV4_L2TPv3 vlan insert on + SW checksum offload
> check
> +===============================================================
> =========
> +
> +1. ./x86_64-native-linuxapp-gcc/app/testpmd -l 6-9 -n 4 -w af:01.0 -- -i --
> rxq=16 --txq=16 --portmask=0x1 --nb-cores=2 --enable-rx-cksum
> +
> +2. DUT create fdir rules for MAC_IPV4_L2TPv3 with queue index and mark::
> +
> + flow create 0 ingress pattern eth / ipv4 / l2tpv3oip session_id is 1 / end
> actions queue index 1 / mark id 4 / end
> + flow create 0 ingress pattern eth / ipv4 / l2tpv3oip session_id is 2 / end
> actions queue index 2 / mark id 3 / end
> + flow create 0 ingress pattern eth / ipv4 / l2tpv3oip session_id is 3 / end
> actions queue index 3 / mark id 2 / end
> + flow create 0 ingress pattern eth / ipv4 / l2tpv3oip session_id is 4 / end
> actions queue index 4 / mark id 1 / end
> +
> +3. Enable vlan filter and add tx vlan offload on port 0::
> +
> + testpmd> port stop all
> + testpmd> rx_vlan add 1 0
> + testpmd> vlan set filter on 0
> + testpmd> tx_vlan set 0 1
> + testpmd> port start all
> + testpmd> set fwd mac
> + testpmd> set verbose 1
> +
> +4. Tester send matched packets without vlan::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(proto=115)/L2TP('\x00\x00\x00\x0
> 2')/Raw('x'*480)], iface="enp134s0f0")
> +
> +5. DUT check the packets are distributed to expected queue with mark id
> and fwd with VLAN tag "1" to tester::
> +
> + testpmd> port 0/queue 2: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x8100 - length=522
> - nb_segs=1 - RSS hash=0xf20d0ef3 - RSS queue=0x2 - sw ptype:
> L2_ETHER_VLAN L3_IPV4 - l2_len=18 - l3_len=20 - Receive queue=0x2
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2268d26880, pkt_len=522, nb_segs=1:
> + rx: l2_len=18 ethertype=800 l3_len=20 l4_proto=115 l4_len=0
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: flags=PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> + 17:25:40.615279 a4:bf:01:6a:62:58 > 00:11:22:33:44:55, ethertype 802.1Q
> (0x8100), length 522: vlan 1, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 1, offset 0,
> flags [none], proto unknown (115), length 504, bad cksum 123 (->7a90)!)
> + 127.0.0.1 > 127.0.0.1: ip-proto-115 484
> +
> +6. enable sw checksum::
> +
> + testpmd> set fwd csum
> + Set csum packet forwarding mode
> + testpmd> port stop all
> + testpmd> csum set ip sw 0
> + testpmd> csum set udp sw 0
> + testpmd> port start all
> + testpmd> start
> +
> +7. Tester send mismatched packets with incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(proto=115,chksum=0x123)/L2TP('\
> x00\x00\x00\x22')/Raw('x'*480)], iface="enp134s0f0")
> +
> +8. DUT check the packets are not distributed to expected queue without
> mark id and report the checksum error::
> +
> + port 0/queue 3: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x8100 - length=522
> - nb_segs=1 - RSS hash=0xf20d0ef3 - RSS queue=0x3 - sw ptype:
> L2_ETHER_VLAN L3_IPV4 - l2_len=18 - l3_len=20 - Receive queue=0x3
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2268e42f80, pkt_len=522, nb_segs=1:
> + rx: l2_len=18 ethertype=800 l3_len=20 l4_proto=115 l4_len=0
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: flags=PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> +9. DUT verify rule can be listed and destroyed::
> +
> + testpmd> flow list 0
> + ID Group Prio Attr Rule
> + 0 0 0 i-- ETH IPV4 L2TPV3OIP => QUEUE MARK
> + 1 0 0 i-- ETH IPV4 L2TPV3OIP => QUEUE MARK
> + 2 0 0 i-- ETH IPV4 L2TPV3OIP => QUEUE MARK
> + 3 0 0 i-- ETH IPV4 L2TPV3OIP => QUEUE MARK
> + testpmd> flow destroy 0 rule 1
> +
> +10. Tester send matched packets with incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(proto=115,chksum=0x123)/L2TP('\
> x00\x00\x00\x02')/Raw('x'*480)], iface="enp134s0f0")
> +
> +11.DUT check the packets are not distributed to expected queue without
> mark id and report the checksum error::
> +
> + testpmd> port 0/queue 3: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x8100 - length=522
> - nb_segs=1 - RSS hash=0xf20d0ef3 - RSS queue=0x3 - sw ptype:
> L2_ETHER_VLAN L3_IPV4 - l2_len=18 - l3_len=20 - Receive queue=0x3
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2268e42640, pkt_len=522, nb_segs=1:
> + rx: l2_len=18 ethertype=800 l3_len=20 l4_proto=115 l4_len=0
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: flags=PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> +
> +Test Case 16: MAC_IPV4_ESP vlan strip on + HW checksum offload check
> +===============================================================
> =====
> +
> +The pre-steps are as l2tp_esp_iavf_test_plan.
> +
> +1. ./x86_64-native-linuxapp-gcc/app/testpmd -l 6-9 -n 4 -w af:01.0 -- -i --
> rxq=16 --txq=16 --portmask=0x1 --nb-cores=2 --enable-rx-cksum
> +
> +2. DUT create fdir rules for MAC_IPV4_ESP with queue index and mark::
> +
> + flow create 0 ingress pattern eth / ipv4 / esp spi is 1 / end actions queue
> index 1 / mark id 4 / end
> + flow create 0 ingress pattern eth / ipv4 / esp spi is 2 / end actions queue
> index 2 / mark id 3 / end
> + flow create 0 ingress pattern eth / ipv4 / esp spi is 3 / end actions queue
> index 3 / mark id 2 / end
> + flow create 0 ingress pattern eth / ipv4 / esp spi is 4 / end actions queue
> index 4 / mark id 1 / end
> +
> +3. Enable vlan filter and receipt of VLAN packets with VLAN Tag Identifier 1
> on port 0, Enable vlan strip on VF0::
> +
> + testpmd> vlan set filter on 0
> + testpmd> rx_vlan add 1 0
> + testpmd> vlan set strip on 0
> +
> +4. enable hw checksum::
> +
> + testpmd> set fwd csum
> + Set csum packet forwarding mode
> + testpmd> set verbose 1
> + testpmd> port stop all
> + testpmd> csum set ip hw 0
> + testpmd> csum set udp hw 0
> + testpmd> port start all
> + testpmd> start
> +
> +5. Tester send matched packets with VLAN tag "1" and incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=50,chksum=
> 0x123)/ESP(spi=1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +6. DUT check the packets are distributed to expected queue with mark id
> and fwd without VLAN tag "1", and report the checksum error::
> +
> + testpmd> port 0/queue 1: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x0800 - length=522
> - nb_segs=1 - RSS hash=0xeb9be2c9 - RSS queue=0x1 - VLAN tci=0x1 - sw
> ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x1
> + ol_flags: PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2268c0a180, pkt_len=522, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=50 l4_len=0
> flags=PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> + 17:39:12.063112 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv4
> (0x0800), length 522: (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto ESP
> (50), length 508)
> + 127.0.0.1 > 127.0.0.1: ESP(spi=0x00000001,seq=0x0), length 488
> +
> +7. Tester send mismatched packets with VLAN tag "1" and incorrect
> checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=50,chksum=
> 0x123)/ESP(spi=11)/Raw('x'*480)], iface="enp134s0f0")
> +
> +8. DUT check the packets are not distributed to expected queue without
> mark id and fwd without VLAN tag "1", and report the checksum error::
> +
> + port 0/queue 9: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x0800 - length=522
> - nb_segs=1 - RSS hash=0xeb9be2c9 - RSS queue=0x9 - VLAN tci=0x1 - sw
> ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x9
> + ol_flags: PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x226960fd00, pkt_len=522, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=50 l4_len=0
> flags=PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> + 17:40:33.967072 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv4
> (0x0800), length 522: (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto ESP
> (50), length 508)
> + 127.0.0.1 > 127.0.0.1: ESP(spi=0x0000000b,seq=0x0), length 488
> +
> +9. DUT verify rule can be listed and destroyed::
> +
> + testpmd> flow list 0
> + 0 0 0 i-- ETH IPV4 ESP => QUEUE MARK
> + 1 0 0 i-- ETH IPV4 ESP => QUEUE MARK
> + 2 0 0 i-- ETH IPV4 ESP => QUEUE MARK
> + 3 0 0 i-- ETH IPV4 ESP => QUEUE MARK
> + testpmd> flow destroy 0 rule 0
> +
> +10. Tester send matched packets with VLAN tag "1" and incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/Dot1Q(vlan=1)/IP(proto=50,chksum=
> 0x123)/ESP(spi=1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +11.DUT check the packets are not distributed to expected queue without
> mark id and and fwd without VLAN tag "1", and report the checksum error::
> +
> + testpmd> port 0/queue 9: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x0800 - length=522
> - nb_segs=1 - RSS hash=0xeb9be2c9 - RSS queue=0x9 - VLAN tci=0x1 - sw
> ptype: L2_ETHER L3_IPV4 - l2_len=14 - l3_len=20 - Receive queue=0x9
> + ol_flags: PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x226960f3c0, pkt_len=522, nb_segs=1:
> + rx: l2_len=14 ethertype=800 l3_len=20 l4_proto=50 l4_len=0
> flags=PKT_RX_VLAN PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_VLAN_STRIPPED
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: m->l2_len=14 m->l3_len=20 m->l4_len=0
> + tx: flags=PKT_TX_IP_CKSUM PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> + 17:42:29.419400 00:11:22:33:44:55 > 02:00:00:00:00:00, ethertype IPv4
> (0x0800), length 522: (tos 0x0, ttl 64, id 1, offset 0, flags [none], proto ESP
> (50), length 508)
> + 127.0.0.1 > 127.0.0.1: ESP(spi=0x00000001,seq=0x0), length 488
> +
> +
> +Test Case 17: MAC_IPV6_NAT-T-ESP vlan insert on + SW checksum offload
> check
> +===============================================================
> ============
> +
> +1. ./x86_64-native-linuxapp-gcc/app/testpmd -l 6-9 -n 4 -w af:01.0 -- -i --
> rxq=16 --txq=16 --portmask=0x1 --nb-cores=2 --enable-rx-cksum
> +
> +2. DUT create fdir rules for MAC_IPV6_NAT-T-ESP with queue index and
> mark::
> +
> + flow create 0 ingress pattern eth / ipv4 / udp / esp spi is 1 / end actions
> queue index 1 / mark id 4 / end
> + flow create 0 ingress pattern eth / ipv4 / udp / esp spi is 2 / end actions
> queue index 2 / mark id 3 / end
> + flow create 0 ingress pattern eth / ipv4 / udp / esp spi is 3 / end actions
> queue index 3 / mark id 2 / end
> + flow create 0 ingress pattern eth / ipv4 / udp / esp spi is 4 / end actions
> queue index 4 / mark id 1 / end
> +
> +3. Enable vlan filter and add tx vlan offload on port 0::
> +
> + testpmd> port stop all
> + testpmd> rx_vlan add 1 0
> + testpmd> vlan set filter on 0
> + testpmd> tx_vlan set 0 1
> + testpmd> port start all
> + testpmd> set fwd mac
> + testpmd> set verbose 1
> +
> +4. Tester send matched packets without vlan::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(chksum=0x123)/UDP(dport=4500)/
> ESP(spi=1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +5. DUT check the packets are distributed to expected queue with mark id
> and fwd with VLAN tag "1" to tester::
> +
> + testpmd> port 0/queue 1: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x8100 - length=534
> - nb_segs=1 - RSS hash=0x89b546af - RSS queue=0x1 - sw ptype:
> L2_ETHER_VLAN L3_IPV4 L4_UDP - l2_len=18 - l3_len=20 - l4_len=8 - Receive
> queue=0x1
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2268c0a180, pkt_len=534, nb_segs=1:
> + rx: l2_len=18 ethertype=800 l3_len=20 l4_proto=17 l4_len=8
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: flags=PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> + 17:49:14.935149 a4:bf:01:6a:62:58 > 00:11:22:33:44:55, ethertype 802.1Q
> (0x8100), length 534: vlan 1, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 1, offset 0,
> flags [none], proto UDP (17), length 516, bad cksum 123 (->7ae6)!)
> + 127.0.0.1.4500 > 127.0.0.1.4500: UDP-encap:
> ESP(spi=0x00000001,seq=0x0), length 488
> +
> +6. enable sw checksum::
> +
> + testpmd> set fwd csum
> + Set csum packet forwarding mode
> + testpmd> port stop all
> + testpmd> csum set ip sw 0
> + testpmd> csum set udp sw 0
> + testpmd> port start all
> + testpmd> start
> +
> +7. Tester send mismatched packets with incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(chksum=0x123)/UDP(dport=4500)/
> ESP(spi=11)/Raw('x'*480)], iface="enp134s0f0")
> +
> +8. DUT check the packets are not distributed to expected queue without
> mark id and report the checksum error::
> +
> + port 0/queue 15: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x8100 - length=534
> - nb_segs=1 - RSS hash=0x89b546af - RSS queue=0xf - sw ptype:
> L2_ETHER_VLAN L3_IPV4 L4_UDP - l2_len=18 - l3_len=20 - l4_len=8 - Receive
> queue=0xf
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2269cba700, pkt_len=534, nb_segs=1:
> + rx: l2_len=18 ethertype=800 l3_len=20 l4_proto=17 l4_len=8
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: flags=PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> +9. DUT verify rule can be listed and destroyed::
> +
> + testpmd> flow list 0
> + ID Group Prio Attr Rule
> + 0 0 0 i-- ETH IPV4 UDP ESP => QUEUE MARK
> + 1 0 0 i-- ETH IPV4 UDP ESP => QUEUE MARK
> + 2 0 0 i-- ETH IPV4 UDP ESP => QUEUE MARK
> + 3 0 0 i-- ETH IPV4 UDP ESP => QUEUE MARK
> + testpmd> flow destroy 0 rule 0
> +
> +10. Tester send matched packets with incorrect checksum::
> +
> +
> sendp([Ether(dst="00:11:22:33:44:55")/IP(chksum=0x123)/UDP(dport=4500)/
> ESP(spi=1)/Raw('x'*480)], iface="enp134s0f0")
> +
> +11.DUT check the packets are not distributed to expected queue without
> mark id and report the checksum error::
> +
> + testpmd> port 0/queue 15: received 1 packets
> + src=A4:BF:01:6A:62:58 - dst=00:11:22:33:44:55 - type=0x8100 - length=534
> - nb_segs=1 - RSS hash=0x89b546af - RSS queue=0xf - sw ptype:
> L2_ETHER_VLAN L3_IPV4 L4_UDP - l2_len=18 - l3_len=20 - l4_len=8 - Receive
> queue=0xf
> + ol_flags: PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD
> PKT_RX_IP_CKSUM_BAD PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + -----------------
> + port=0, mbuf=0x2269cb9dc0, pkt_len=534, nb_segs=1:
> + rx: l2_len=18 ethertype=800 l3_len=20 l4_proto=17 l4_len=8
> flags=PKT_RX_RSS_HASH PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_BAD
> PKT_RX_OUTER_L4_CKSUM_UNKNOWN
> + tx: flags=PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> --
> 2.17.1
prev parent reply other threads:[~2020-06-03 2:30 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-02 18:17 Fu Qi
2020-06-03 2:30 ` Tu, Lijuan [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=8CE3E05A3F976642AAB0F4675D0AD20E0BC587D2@SHSMSX101.ccr.corp.intel.com \
--to=lijuan.tu@intel.com \
--cc=dts@dpdk.org \
--cc=qi.fu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).