[PATCH v2 01/10] net/ice/base: re-enable bypass mode for E822

[Bruce Richardson <bruce.richardson@intel.com>]

From: Jacob Keller <jacob.e.keller@intel.com>

When removing bypass mode, the code for E822 bypass was completely
removed in error. This code should be maintained in DPDK so re-add the
necessary functions.

Fixes: ce9ad8c5bc6d ("net/ice/base: remove PHY port timer bypass mode")
Cc: stable@dpdk.org

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
---
 drivers/net/ice/base/ice_ptp_hw.c | 117 ++++++++++++++++++++++++++++--
 drivers/net/ice/base/ice_ptp_hw.h |   2 +-
 drivers/net/ice/ice_ethdev.c      |   2 +-
 3 files changed, 113 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ice/base/ice_ptp_hw.c b/drivers/net/ice/base/ice_ptp_hw.c
index 2a112fea12..1e92e5ff21 100644
--- a/drivers/net/ice/base/ice_ptp_hw.c
+++ b/drivers/net/ice/base/ice_ptp_hw.c
@@ -4468,18 +4468,103 @@ ice_stop_phy_timer_e822(struct ice_hw *hw, u8 port, bool soft_reset)
 	return 0;
 }
 
+/**
+ * ice_phy_cfg_fixed_tx_offset_e822 - Configure Tx offset for bypass mode
+ * @hw: pointer to the HW struct
+ * @port: the PHY port to configure
+ *
+ * Calculate and program the fixed Tx offset, and indicate that the offset is
+ * ready. This can be used when operating in bypass mode.
+ */
+static int ice_phy_cfg_fixed_tx_offset_e822(struct ice_hw *hw, u8 port)
+{
+	enum ice_ptp_link_spd link_spd;
+	enum ice_ptp_fec_mode fec_mode;
+	u64 total_offset;
+	int err;
+
+	err = ice_phy_get_speed_and_fec_e822(hw, port, &link_spd, &fec_mode);
+	if (err)
+		return err;
+
+	total_offset = ice_calc_fixed_tx_offset_e822(hw, link_spd);
+
+	/* Program the fixed Tx offset into the P_REG_TOTAL_TX_OFFSET_L
+	 * register, then indicate that the Tx offset is ready. After this,
+	 * timestamps will be enabled.
+	 *
+	 * Note that this skips including the more precise offsets generated
+	 * by the Vernier calibration.
+	 */
+
+	err = ice_write_64b_phy_reg_e822(hw, port, P_REG_TOTAL_TX_OFFSET_L,
+					 total_offset);
+	if (err)
+		return err;
+
+	err = ice_write_phy_reg_e822(hw, port, P_REG_TX_OR, 1);
+	if (err)
+		return err;
+
+	return ICE_SUCCESS;
+}
+
+/**
+ * ice_phy_cfg_rx_offset_e822 - Configure fixed Rx offset for bypass mode
+ * @hw: pointer to the HW struct
+ * @port: the PHY port to configure
+ *
+ * Calculate and program the fixed Rx offset, and indicate that the offset is
+ * ready. This can be used when operating in bypass mode.
+ */
+static int ice_phy_cfg_fixed_rx_offset_e822(struct ice_hw *hw, u8 port)
+{
+	enum ice_ptp_link_spd link_spd;
+	enum ice_ptp_fec_mode fec_mode;
+	u64 total_offset;
+	int err;
+
+	err = ice_phy_get_speed_and_fec_e822(hw, port, &link_spd, &fec_mode);
+	if (err)
+		return err;
+
+	total_offset = ice_calc_fixed_rx_offset_e822(hw, link_spd);
+
+	/* Program the fixed Rx offset into the P_REG_TOTAL_RX_OFFSET_L
+	 * register, then indicate that the Rx offset is ready. After this,
+	 * timestamps will be enabled.
+	 *
+	 * Note that this skips including the more precise offsets generated
+	 * by Vernier calibration.
+	 */
+	err = ice_write_64b_phy_reg_e822(hw, port, P_REG_TOTAL_RX_OFFSET_L,
+					 total_offset);
+	if (err)
+		return err;
+
+	err = ice_write_phy_reg_e822(hw, port, P_REG_RX_OR, 1);
+	if (err)
+		return err;
+
+	return ICE_SUCCESS;
+}
+
 /**
  * ice_start_phy_timer_e822 - Start the PHY clock timer
  * @hw: pointer to the HW struct
  * @port: the PHY port to start
+ * @bypass: if true, start the PHY in bypass mode
  *
  * Start the clock of a PHY port. This must be done as part of the flow to
  * re-calibrate Tx and Rx timestamping offsets whenever the clock time is
  * initialized or when link speed changes.
  *
- * Hardware will take Vernier measurements on Tx or Rx of packets.
+ * Bypass mode enables timestamps immediately without waiting for Vernier
+ * calibration to complete. Hardware will still continue taking Vernier
+ * measurements on Tx or Rx of packets, but they will not be applied to
+ * timestamps.
  */
-int ice_start_phy_timer_e822(struct ice_hw *hw, u8 port)
+int ice_start_phy_timer_e822(struct ice_hw *hw, u8 port, bool bypass)
 {
 	u32 lo, hi, val;
 	u64 incval;
@@ -4544,15 +4629,35 @@ int ice_start_phy_timer_e822(struct ice_hw *hw, u8 port)
 
 	ice_ptp_exec_tmr_cmd(hw);
 
+	if (bypass) {
+		/* Enter BYPASS mode, enabling timestamps immediately. */
+		val |= P_REG_PS_BYPASS_MODE_M;
+		err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val);
+		if (err)
+			return err;
+	}
+
 	val |= P_REG_PS_ENA_CLK_M;
 	err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val);
 	if (err)
 		return err;
 
-	val |= P_REG_PS_LOAD_OFFSET_M;
-	err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val);
-	if (err)
-		return err;
+	if (bypass) {
+		/* Program the fixed Tx offset */
+		err = ice_phy_cfg_fixed_tx_offset_e822(hw, port);
+		if (err)
+			return err;
+
+		/* Program the fixed Rx offset */
+		err = ice_phy_cfg_fixed_rx_offset_e822(hw, port);
+		if (err)
+			return err;
+	} else {
+		val |= P_REG_PS_LOAD_OFFSET_M;
+		err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val);
+		if (err)
+			return err;
+	}
 
 	ice_ptp_exec_tmr_cmd(hw);
 
diff --git a/drivers/net/ice/base/ice_ptp_hw.h b/drivers/net/ice/base/ice_ptp_hw.h
index 5d6636c0d1..534e05a8dd 100644
--- a/drivers/net/ice/base/ice_ptp_hw.h
+++ b/drivers/net/ice/base/ice_ptp_hw.h
@@ -277,7 +277,7 @@ ice_phy_get_speed_and_fec_e822(struct ice_hw *hw, u8 port,
 void ice_phy_cfg_lane_e822(struct ice_hw *hw, u8 port);
 int
 ice_stop_phy_timer_e822(struct ice_hw *hw, u8 port, bool soft_reset);
-int ice_start_phy_timer_e822(struct ice_hw *hw, u8 port);
+int ice_start_phy_timer_e822(struct ice_hw *hw, u8 port, bool bypass);
 int ice_phy_cfg_tx_offset_e822(struct ice_hw *hw, u8 port);
 int ice_phy_cfg_rx_offset_e822(struct ice_hw *hw, u8 port);
 int
diff --git a/drivers/net/ice/ice_ethdev.c b/drivers/net/ice/ice_ethdev.c
index 61bff016be..2f9bcbd3a5 100644
--- a/drivers/net/ice/ice_ethdev.c
+++ b/drivers/net/ice/ice_ethdev.c
@@ -2540,7 +2540,7 @@ ice_dev_init(struct rte_eth_dev *dev)
 	ice_ptp_init_phy_model(hw);
 
 	if (hw->phy_model == ICE_PHY_E822) {
-		ret = ice_start_phy_timer_e822(hw, hw->pf_id);
+		ret = ice_start_phy_timer_e822(hw, hw->pf_id, true);
 		if (ret)
 			PMD_INIT_LOG(ERR, "Failed to start phy timer");
 	}
-- 
2.43.0