patches for DPDK stable branches
 help / color / mirror / Atom feed
* [PATCH 20.11] doc: add more instructions for running as non-root
@ 2022-08-01 12:19 Dmitry Kozlyuk
  2022-08-09 15:09 ` Xueming(Steven) Li
  0 siblings, 1 reply; 3+ messages in thread
From: Dmitry Kozlyuk @ 2022-08-01 12:19 UTC (permalink / raw)
  To: stable; +Cc: Xueming(Steven) Li, Bruce Richardson

[ upstream commit 979bb5d493fbbce77eaaf2b4a01ee98f93f76dd9 ]

The guide to run DPDK applications as non-root in Linux
did not provide specific instructions to configure the required access
and did not explain why each bit is needed.
The latter is important because running as non-root
is one of the ways to tighten security and grant minimal permissions.

Signed-off-by: Dmitry Kozlyuk <dkozlyuk@nvidia.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
---
Upstream commit references things missing from 21.11:
new dpdk-hugepages.py options and memory mapping documentation.
The script call replaced with a direct mount command.
Documentation reference is dropped as non-essential.

 doc/guides/linux_gsg/enable_func.rst | 85 +++++++++++++++++++---------
 1 file changed, 58 insertions(+), 27 deletions(-)

diff --git a/doc/guides/linux_gsg/enable_func.rst b/doc/guides/linux_gsg/enable_func.rst
index 25f87f6b1a..7538d04d97 100644
--- a/doc/guides/linux_gsg/enable_func.rst
+++ b/doc/guides/linux_gsg/enable_func.rst
@@ -66,13 +66,62 @@ The application can then determine what action to take, if any, if the HPET is n
 Running DPDK Applications Without Root Privileges
 -------------------------------------------------
 
-In order to run DPDK as non-root, the following Linux filesystem objects'
-permissions should be adjusted to ensure that the Linux account being used to
-run the DPDK application has access to them:
+The following sections describe generic requirements and configuration
+for running DPDK applications as non-root.
+There may be additional requirements documented for some drivers.
 
-*   All directories which serve as hugepage mount points, for example, ``/dev/hugepages``
+Hugepages
+~~~~~~~~~
 
-*   If the HPET is to be used,  ``/dev/hpet``
+Hugepages must be reserved as root before running the application as non-root,
+for example::
+
+  sudo dpdk-hugepages.py --reserve 1G
+
+If multi-process is not required, running with ``--in-memory``
+bypasses the need to access hugepage mount point and files within it.
+Otherwise, hugepage directory must be made accessible
+for writing to the unprivileged user.
+A good way for managing multiple applications using hugepages
+is to mount the filesystem with group permissions
+and add a supplementary group to each application or container.
+
+One option is to mount manually::
+
+  mount -t hugetlbfs -o pagesize=1G,uid=`id -u`,gid=`id -g` nodev $HOME/huge-1G
+
+In production environment, the OS can manage mount points
+(`systemd example <https://github.com/systemd/systemd/blob/main/units/dev-hugepages.mount>`_).
+
+The ``hugetlb`` filesystem has additional options to guarantee or limit
+the amount of memory that is possible to allocate using the mount point.
+Refer to the `documentation <https://www.kernel.org/doc/Documentation/vm/hugetlbpage.txt>`_.
+
+.. note::
+
+   Using ``vfio-pci`` kernel driver, if applicable, can eliminate the need
+   for physical addresses and therefore eliminate the permission requirements
+   described below.
+
+If the driver requires using physical addresses (PA),
+the executable file must be granted additional capabilities:
+
+* ``SYS_ADMIN`` to read ``/proc/self/pagemaps``
+* ``IPC_LOCK`` to lock hugepages in memory
+
+.. code-block:: console
+
+   setcap cap_ipc_lock,cap_sys_admin+ep <executable>
+
+If physical addresses are not accessible,
+the following message will appear during EAL initialization::
+
+  EAL: rte_mem_virt2phy(): cannot open /proc/self/pagemap: Permission denied
+
+It is harmless in case PA are not needed.
+
+Resource Limits
+~~~~~~~~~~~~~~~
 
 When running as non-root user, there may be some additional resource limits
 that are imposed by the system. Specifically, the following resource limits may
@@ -87,8 +136,10 @@ need to be adjusted in order to ensure normal DPDK operation:
 The above limits can usually be adjusted by editing
 ``/etc/security/limits.conf`` file, and rebooting.
 
-Additionally, depending on which kernel driver is in use, the relevant
-resources also should be accessible by the user running the DPDK application.
+Device Control
+~~~~~~~~~~~~~~
+
+If the HPET is to be used, ``/dev/hpet`` permissions must be adjusted.
 
 For ``vfio-pci`` kernel driver, the following Linux file system objects'
 permissions should be adjusted:
@@ -98,26 +149,6 @@ permissions should be adjusted:
 * The directories under ``/dev/vfio`` that correspond to IOMMU group numbers of
   devices intended to be used by DPDK, for example, ``/dev/vfio/50``
 
-.. note::
-
-    The instructions below will allow running DPDK with ``igb_uio`` or
-    ``uio_pci_generic`` drivers as non-root with older Linux kernel versions.
-    However, since version 4.0, the kernel does not allow unprivileged processes
-    to read the physical address information from the pagemaps file, making it
-    impossible for those processes to be used by non-privileged users. In such
-    cases, using the VFIO driver is recommended.
-
-For ``igb_uio`` or ``uio_pci_generic`` kernel drivers, the following Linux file
-system objects' permissions should be adjusted:
-
-*   The userspace-io device files in  ``/dev``, for example,  ``/dev/uio0``, ``/dev/uio1``, and so on
-
-*   The userspace-io sysfs config and resource files, for example for ``uio0``::
-
-       /sys/class/uio/uio0/device/config
-       /sys/class/uio/uio0/device/resource*
-
-
 Power Management and Power Saving Functionality
 -----------------------------------------------
 
-- 
2.25.1


^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2022-08-15  8:22 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-08-01 12:19 [PATCH 20.11] doc: add more instructions for running as non-root Dmitry Kozlyuk
2022-08-09 15:09 ` Xueming(Steven) Li
2022-08-15  8:22   ` Xueming(Steven) Li

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).