* [dpdk-users] i40e virtual function doesn't work on virtual machine
@ 2017-08-04 12:47 Dirk-Holger Lenz
2017-08-04 12:56 ` Dirk-Holger Lenz
0 siblings, 1 reply; 2+ messages in thread
From: Dirk-Holger Lenz @ 2017-08-04 12:47 UTC (permalink / raw)
To: users
when for a virtual function running on a virtual machine
rte_eth_dev_start() is called the dpdk returns an error
and logs the following error messages:
i40evf_execute_vf_cmd(): No response for 6
i40evf_configure_vsi_queues(): Failed to execute command of
VIRTCHNL_OP_CONFIG_VSI_QUEUES
i40evf_dev_start(): configure queues failed
short time before it logged:
i40evf_execute_vf_cmd(): No response for 28
i40evf_disable_vlan_strip(): Failed to execute command of
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING
But this correlates to the log on the host:
Aug 4 14:09:43 ng40x kernel: [12176.208968] i40e 0000:82:00.1: Invalid
message from VF 0, opcode 28, len 0
Aug 4 14:09:48 ng40x kernel: [12181.414724] i40e 0000:82:00.1: Invalid
message from VF 1, opcode 28, len 0
The host is running Ubuntu linux with kernel 4.8.0-45-lowlatency.
The primary function of the i40e is driven by the linux kernel driver and
16 virtual functions are created.
The virtual machine is running Ubuntu linux with kernel
4.8.0-45-lowlatency as well.
It is used dpdk 17.08rc4.
When a similar scenario is used on the host directly using virtual
functions as well,
the dpdk logs the VIRTCHNL_OP_DISABLE_VLAN_STRIPPING problem but not the
VIRTCHNL_OP_CONFIG_VSI_QUEUES problem and it works fine.
When I hardly make the i40evf_execute_vf_cmd() function return 0 the virtual
function starts and is able to transmit and receive packets at high rate.
Here are the logs which are given in this case:
i40evf_execute_vf_cmd(): No response for 28
i40evf_execute_vf_cmd(): No response for 6
i40evf_execute_vf_cmd(): No response for 7
i40evf_execute_vf_cmd(): No response for 10
i40evf_execute_vf_cmd(): No response for 8
i40evf_execute_vf_cmd(): No response for 8
i40evf_execute_vf_cmd(): No response for 14
note: we are using a regression test scenario which was running every
night. the last
good run we had Wednesday with dpdk 17.05. Then we switched to 17.08rc3/rc4.
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [dpdk-users] i40e virtual function doesn't work on virtual machine
2017-08-04 12:47 [dpdk-users] i40e virtual function doesn't work on virtual machine Dirk-Holger Lenz
@ 2017-08-04 12:56 ` Dirk-Holger Lenz
0 siblings, 0 replies; 2+ messages in thread
From: Dirk-Holger Lenz @ 2017-08-04 12:56 UTC (permalink / raw)
To: users
additional information to the i40e:
i40e 0000:82:00.1: fw 5.0.40043 api 1.5 nvm 5.05 0x80002892 1.1568.0
On 08/04/2017 02:47 PM, Dirk-Holger Lenz wrote:
> when for a virtual function running on a virtual machine
>
> rte_eth_dev_start() is called the dpdk returns an error
>
> and logs the following error messages:
>
> i40evf_execute_vf_cmd(): No response for 6
> i40evf_configure_vsi_queues(): Failed to execute command of
> VIRTCHNL_OP_CONFIG_VSI_QUEUES
> i40evf_dev_start(): configure queues failed
>
> short time before it logged:
>
> i40evf_execute_vf_cmd(): No response for 28
> i40evf_disable_vlan_strip(): Failed to execute command of
> VIRTCHNL_OP_DISABLE_VLAN_STRIPPING
>
> But this correlates to the log on the host:
>
> Aug 4 14:09:43 ng40x kernel: [12176.208968] i40e 0000:82:00.1:
> Invalid message from VF 0, opcode 28, len 0
> Aug 4 14:09:48 ng40x kernel: [12181.414724] i40e 0000:82:00.1:
> Invalid message from VF 1, opcode 28, len 0
>
> The host is running Ubuntu linux with kernel 4.8.0-45-lowlatency.
>
> The primary function of the i40e is driven by the linux kernel driver and
>
> 16 virtual functions are created.
>
> The virtual machine is running Ubuntu linux with kernel
> 4.8.0-45-lowlatency as well.
>
> It is used dpdk 17.08rc4.
>
>
> When a similar scenario is used on the host directly using virtual
> functions as well,
>
> the dpdk logs the VIRTCHNL_OP_DISABLE_VLAN_STRIPPING problem but not the
>
> VIRTCHNL_OP_CONFIG_VSI_QUEUES problem and it works fine.
>
>
> When I hardly make the i40evf_execute_vf_cmd() function return 0 the
> virtual
>
> function starts and is able to transmit and receive packets at high rate.
>
> Here are the logs which are given in this case:
>
> i40evf_execute_vf_cmd(): No response for 28
> i40evf_execute_vf_cmd(): No response for 6
> i40evf_execute_vf_cmd(): No response for 7
> i40evf_execute_vf_cmd(): No response for 10
> i40evf_execute_vf_cmd(): No response for 8
> i40evf_execute_vf_cmd(): No response for 8
> i40evf_execute_vf_cmd(): No response for 14
>
> note: we are using a regression test scenario which was running every
> night. the last
>
> good run we had Wednesday with dpdk 17.05. Then we switched to
> 17.08rc3/rc4.
>
>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2017-08-04 12:56 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-08-04 12:47 [dpdk-users] i40e virtual function doesn't work on virtual machine Dirk-Holger Lenz
2017-08-04 12:56 ` Dirk-Holger Lenz
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).