* [dpdk-users] bnx2x_init failed @ 2018-01-16 16:39 Nirmoy Das 2018-01-16 17:58 ` Patil, Harish 0 siblings, 1 reply; 5+ messages in thread From: Nirmoy Das @ 2018-01-16 16:39 UTC (permalink / raw) To: harish.patil; +Cc: rasesh.mody, users Hi Harish/Rasesh, I am getting following error on NetXtreme II BCM57810 10 Gigabit Ethernet while running dpdk KNI/testpmd application PMD: bnx2x_reg_write32(): offset=0x0000a3c8 val=0x00000800 PMD: bnx2x_init(): Initialization failed, stack notified driver is NOT running! PMD: bnx2x_dev_start(): bnx2x_init failed (-6) EAL: Error - exiting with code: 1 Cause: Could not start port0 (-1) I can't figure out why, its running on 4.4.103-6.38-default and have the required firmware. Do you have any suggestion why we are facing this issue Regards, Nirmoy -- SUSE Linux GmbH, GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB 21284 (AG Nürnberg) Maxfeldstr. 5 D-90409 Nürnberg / Phone: +49-911-740 18-4 ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [dpdk-users] bnx2x_init failed 2018-01-16 16:39 [dpdk-users] bnx2x_init failed Nirmoy Das @ 2018-01-16 17:58 ` Patil, Harish 2018-01-17 10:18 ` Nirmoy Das 0 siblings, 1 reply; 5+ messages in thread From: Patil, Harish @ 2018-01-16 17:58 UTC (permalink / raw) To: Nirmoy Das; +Cc: Mody, Rasesh, users -----Original Message----- From: Nirmoy Das <ndas@suse.de> Date: Tuesday, January 16, 2018 at 8:39 AM To: Harish Patil <Harish.Patil@cavium.com> Cc: "Mody, Rasesh" <Rasesh.Mody@cavium.com>, "users@dpdk.org" <users@dpdk.org> Subject: bnx2x_init failed >Hi Harish/Rasesh, > >I am getting following error on NetXtreme II BCM57810 10 Gigabit >Ethernet while running dpdk KNI/testpmd application > >PMD: bnx2x_reg_write32(): offset=0x0000a3c8 val=0x00000800 >PMD: bnx2x_init(): Initialization failed, stack notified driver is NOT >running! >PMD: bnx2x_dev_start(): bnx2x_init failed (-6) >EAL: Error - exiting with code: 1 > Cause: Could not start port0 (-1) > >I can't figure out why, its running on 4.4.103-6.38-default and have the >required firmware. Do you have any suggestion why we are facing this issue > >Regards, >Nirmoy >-- >SUSE Linux GmbH, GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB >21284 (AG Nürnberg) Maxfeldstr. 5 >D-90409 Nürnberg / Phone: +49-911-740 18-4 Hi Nirmoy, Is it testpmd or KNI or both which is not working? Pls provide the exact cmdline you used to launch the applications? Thanks. > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [dpdk-users] bnx2x_init failed 2018-01-16 17:58 ` Patil, Harish @ 2018-01-17 10:18 ` Nirmoy Das 2018-01-25 13:30 ` nirmoy das 0 siblings, 1 reply; 5+ messages in thread From: Nirmoy Das @ 2018-01-17 10:18 UTC (permalink / raw) To: Patil, Harish; +Cc: Mody, Rasesh, users Hi Harish, kni example application. here's the command that fails. dpdk_example_kni -- -P -p 1 --config="(0,1,2,3)" Adding more details PCI devices for eth0 and eth1 remain bound to bnx2x driver 0000.04:00.0 eth0 0000.04:00.1 eth1 The rest are bound to igb_uio driver 0000.04:00.2 [...] 0000.04:00.7 ########################################### dpdk_example_kni -- -P -p 1 --config="(0,1,2,3)" Fails, Cause: Could not start port0 (-1) ########################################### dpdk_example_kni -- -P -p 2 --config="(1,4,5,6)" Works pci device 04:00.03 Lcore 4 is reading from port1 Lcore 5 is writing to port1 ########################################### dpdk_example_kni -- -P -p 4 --config="(2,1,2,3)" Fails, Cause: Could not start port2 (-1) They are still trying to use Lcore 1&2 Environment: ============ SLES 12 SP3 Kernel 4.4.73-5-default x86_64 dpdk-tools-16.11.1-6.50.x86_64 dpdk-kmp-default-16.11.1_k4.4.73_5-6.50.x86_64 dpdk-16.11.1-6.50.x86_64 Hardware: ========= # /usr/sbin/hwinfo --netcard 87: PCI 400.0: 0200 Ethernet controller [Created at pci.378] Unique ID: rBUF.sL+v+HVDdA2 Parent ID: _Znp.dXj21w8z979 SysFS ID: /devices/pci0000:00/0000:00:02.0/0000:04:00.0 SysFS BusID: 0000:04:00.0 Hardware Class: network Device Name: "NIC Port 1" Model: "Hewlett-Packard Company Flex-10 10Gb 2-port 530FLB Adapter [Meru]" Vendor: pci 0x14e4 "Broadcom" Device: pci 0x168e "NetXtreme II BCM57810 10 Gigabit Ethernet" SubVendor: pci 0x103c "Hewlett-Packard Company" SubDevice: pci 0x1798 "Flex-10 10Gb 2-port 530FLB Adapter [Meru]" Revision: 0x11 Driver: "bnx2x" Driver Modules: "bnx2x" Device File: eth0 Features: FCoEOffload = off, iSCSIOffload = off, StorageOnly = off Memory Range: 0xf6000000-0xf67fffff (ro,non-prefetchable) Memory Range: 0xf5800000-0xf5ffffff (ro,non-prefetchable) Memory Range: 0xf57f0000-0xf57fffff (ro,non-prefetchable) Memory Range: 0xf0000000-0xf007ffff (ro,non-prefetchable,disabled) IRQ: 81 (no events) HW Address: 74:46:a0:f5:03:80 Permanent HW Address: 74:46:a0:f5:03:80 Link detected: no Module Alias: "pci:v000014E4d0000168Esv0000103Csd00001798bc02sc00i00" Driver Info #0: Driver Status: bnx2x is active Driver Activation Cmd: "modprobe bnx2x" Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #56 (PCI bridge) # /sbin/ethtool -i eth0 driver: bnx2x version: 1.712.30-0 firmware-version: bc 7.14.62 expansion-rom-version: bus-info: 0000:04:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes supports-priv-flags: yes On 01/16/2018 06:58 PM, Patil, Harish wrote: > > > -----Original Message----- > From: Nirmoy Das <ndas@suse.de> > Date: Tuesday, January 16, 2018 at 8:39 AM > To: Harish Patil <Harish.Patil@cavium.com> > Cc: "Mody, Rasesh" <Rasesh.Mody@cavium.com>, "users@dpdk.org" > <users@dpdk.org> > Subject: bnx2x_init failed > >> Hi Harish/Rasesh, >> >> I am getting following error on NetXtreme II BCM57810 10 Gigabit >> Ethernet while running dpdk KNI/testpmd application >> >> PMD: bnx2x_reg_write32(): offset=0x0000a3c8 val=0x00000800 >> PMD: bnx2x_init(): Initialization failed, stack notified driver is NOT >> running! >> PMD: bnx2x_dev_start(): bnx2x_init failed (-6) >> EAL: Error - exiting with code: 1 >> Cause: Could not start port0 (-1) >> >> I can't figure out why, its running on 4.4.103-6.38-default and have the >> required firmware. Do you have any suggestion why we are facing this issue >> >> Regards, >> Nirmoy >> -- >> SUSE Linux GmbH, GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB >> 21284 (AG Nürnberg) Maxfeldstr. 5 >> D-90409 Nürnberg / Phone: +49-911-740 18-4 > > > Hi Nirmoy, > Is it testpmd or KNI or both which is not working? > Pls provide the exact cmdline you used to launch the applications? > > Thanks. >> > Nirmoy -- SUSE Linux GmbH, GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB 21284 (AG Nürnberg) Maxfeldstr. 5 D-90409 Nürnberg / Phone: +49-911-740 18-4 ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [dpdk-users] bnx2x_init failed 2018-01-17 10:18 ` Nirmoy Das @ 2018-01-25 13:30 ` nirmoy das 2018-01-31 20:05 ` Patil, Harish 0 siblings, 1 reply; 5+ messages in thread From: nirmoy das @ 2018-01-25 13:30 UTC (permalink / raw) To: Nirmoy Das; +Cc: Patil, Harish, Mody, Rasesh, users Hi Harish, Do you need any other logs/info for this? Regards, Nirmoy On Jan 17, 2018 11:18 AM, "Nirmoy Das" <ndas@suse.de> wrote: > Hi Harish, > > kni example application. > > here's the command that fails. > dpdk_example_kni -- -P -p 1 --config="(0,1,2,3)" > > > > Adding more details > > PCI devices for eth0 and eth1 remain bound to bnx2x driver > > 0000.04:00.0 eth0 > 0000.04:00.1 eth1 > > The rest are bound to igb_uio driver > > 0000.04:00.2 > [...] > 0000.04:00.7 > > ########################################### > dpdk_example_kni -- -P -p 1 --config="(0,1,2,3)" > Fails, Cause: Could not start port0 (-1) > ########################################### > dpdk_example_kni -- -P -p 2 --config="(1,4,5,6)" > Works > pci device 04:00.03 > Lcore 4 is reading from port1 > Lcore 5 is writing to port1 > ########################################### > dpdk_example_kni -- -P -p 4 --config="(2,1,2,3)" > Fails, Cause: Could not start port2 (-1) > They are still trying to use Lcore 1&2 > > > > Environment: > ============ > SLES 12 SP3 > Kernel 4.4.73-5-default x86_64 > dpdk-tools-16.11.1-6.50.x86_64 > dpdk-kmp-default-16.11.1_k4.4.73_5-6.50.x86_64 > dpdk-16.11.1-6.50.x86_64 > > Hardware: > ========= > # /usr/sbin/hwinfo --netcard > 87: PCI 400.0: 0200 Ethernet controller > [Created at pci.378] > Unique ID: rBUF.sL+v+HVDdA2 > Parent ID: _Znp.dXj21w8z979 > SysFS ID: /devices/pci0000:00/0000:00:02.0/0000:04:00.0 > SysFS BusID: 0000:04:00.0 > Hardware Class: network > Device Name: "NIC Port 1" > Model: "Hewlett-Packard Company Flex-10 10Gb 2-port 530FLB Adapter > [Meru]" > Vendor: pci 0x14e4 "Broadcom" > Device: pci 0x168e "NetXtreme II BCM57810 10 Gigabit Ethernet" > SubVendor: pci 0x103c "Hewlett-Packard Company" > SubDevice: pci 0x1798 "Flex-10 10Gb 2-port 530FLB Adapter [Meru]" > Revision: 0x11 > Driver: "bnx2x" > Driver Modules: "bnx2x" > Device File: eth0 > Features: FCoEOffload = off, iSCSIOffload = off, StorageOnly = off > Memory Range: 0xf6000000-0xf67fffff (ro,non-prefetchable) > Memory Range: 0xf5800000-0xf5ffffff (ro,non-prefetchable) > Memory Range: 0xf57f0000-0xf57fffff (ro,non-prefetchable) > Memory Range: 0xf0000000-0xf007ffff (ro,non-prefetchable,disabled) > IRQ: 81 (no events) > HW Address: 74:46:a0:f5:03:80 > Permanent HW Address: 74:46:a0:f5:03:80 > Link detected: no > Module Alias: "pci:v000014E4d0000168Esv0000103Csd00001798bc02sc00i00" > Driver Info #0: > Driver Status: bnx2x is active > Driver Activation Cmd: "modprobe bnx2x" > Config Status: cfg=no, avail=yes, need=no, active=unknown > Attached to: #56 (PCI bridge) > > > # /sbin/ethtool -i eth0 > driver: bnx2x > version: 1.712.30-0 > firmware-version: bc 7.14.62 > expansion-rom-version: > bus-info: 0000:04:00.0 > supports-statistics: yes > supports-test: yes > supports-eeprom-access: yes > supports-register-dump: yes > supports-priv-flags: yes > > On 01/16/2018 06:58 PM, Patil, Harish wrote: > > > > > > -----Original Message----- > > From: Nirmoy Das <ndas@suse.de> > > Date: Tuesday, January 16, 2018 at 8:39 AM > > To: Harish Patil <Harish.Patil@cavium.com> > > Cc: "Mody, Rasesh" <Rasesh.Mody@cavium.com>, "users@dpdk.org" > > <users@dpdk.org> > > Subject: bnx2x_init failed > > > >> Hi Harish/Rasesh, > >> > >> I am getting following error on NetXtreme II BCM57810 10 Gigabit > >> Ethernet while running dpdk KNI/testpmd application > >> > >> PMD: bnx2x_reg_write32(): offset=0x0000a3c8 val=0x00000800 > >> PMD: bnx2x_init(): Initialization failed, stack notified driver is NOT > >> running! > >> PMD: bnx2x_dev_start(): bnx2x_init failed (-6) > >> EAL: Error - exiting with code: 1 > >> Cause: Could not start port0 (-1) > >> > >> I can't figure out why, its running on 4.4.103-6.38-default and have the > >> required firmware. Do you have any suggestion why we are facing this > issue > >> > >> Regards, > >> Nirmoy > >> -- > >> SUSE Linux GmbH, GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB > >> 21284 (AG Nürnberg) Maxfeldstr. 5 > >> D-90409 Nürnberg / Phone: +49-911-740 18-4 > > > > > > Hi Nirmoy, > > Is it testpmd or KNI or both which is not working? > > Pls provide the exact cmdline you used to launch the applications? > > > > Thanks. > >> > > > > Nirmoy > -- > SUSE Linux GmbH, GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB > 21284 (AG Nürnberg) Maxfeldstr. 5 > D-90409 Nürnberg / Phone: +49-911-740 18-4 > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [dpdk-users] bnx2x_init failed 2018-01-25 13:30 ` nirmoy das @ 2018-01-31 20:05 ` Patil, Harish 0 siblings, 0 replies; 5+ messages in thread From: Patil, Harish @ 2018-01-31 20:05 UTC (permalink / raw) To: nirmoy das, Nirmoy Das; +Cc: Mody, Rasesh, users Hi Nirmoy We will have to internally try this test case and get back to you. Thanks. From: nirmoy das <nirmoy.aiemd@gmail.com<mailto:nirmoy.aiemd@gmail.com>> Date: Thursday, January 25, 2018 at 5:30 AM To: Nirmoy Das <ndas@suse.de<mailto:ndas@suse.de>> Cc: Harish Patil <Harish.Patil@cavium.com<mailto:Harish.Patil@cavium.com>>, "Mody, Rasesh" <Rasesh.Mody@cavium.com<mailto:Rasesh.Mody@cavium.com>>, "users@dpdk.org<mailto:users@dpdk.org>" <users@dpdk.org<mailto:users@dpdk.org>> Subject: Re: [dpdk-users] bnx2x_init failed Hi Harish, Do you need any other logs/info for this? Regards, Nirmoy On Jan 17, 2018 11:18 AM, "Nirmoy Das" <ndas@suse.de<mailto:ndas@suse.de>> wrote: Hi Harish, kni example application. here's the command that fails. dpdk_example_kni -- -P -p 1 --config="(0,1,2,3)" Adding more details PCI devices for eth0 and eth1 remain bound to bnx2x driver 0000.04:00.0 eth0 0000.04:00.1 eth1 The rest are bound to igb_uio driver 0000.04:00.2 [...] 0000.04:00.7 ########################################### dpdk_example_kni -- -P -p 1 --config="(0,1,2,3)" Fails, Cause: Could not start port0 (-1) ########################################### dpdk_example_kni -- -P -p 2 --config="(1,4,5,6)" Works pci device 04:00.03 Lcore 4 is reading from port1 Lcore 5 is writing to port1 ########################################### dpdk_example_kni -- -P -p 4 --config="(2,1,2,3)" Fails, Cause: Could not start port2 (-1) They are still trying to use Lcore 1&2 Environment: ============ SLES 12 SP3 Kernel 4.4.73-5-default x86_64 dpdk-tools-16.11.1-6.50.x86_64 dpdk-kmp-default-16.11.1_k4.4.73_5-6.50.x86_64 dpdk-16.11.1-6.50.x86_64 Hardware: ========= # /usr/sbin/hwinfo --netcard 87: PCI 400.0: 0200 Ethernet controller [Created at pci.378] Unique ID: rBUF.sL+v+HVDdA2 Parent ID: _Znp.dXj21w8z979 SysFS ID: /devices/pci0000:00/0000:00:02.0/0000:04:00.0 SysFS BusID: 0000:04:00.0 Hardware Class: network Device Name: "NIC Port 1" Model: "Hewlett-Packard Company Flex-10 10Gb 2-port 530FLB Adapter [Meru]" Vendor: pci 0x14e4 "Broadcom" Device: pci 0x168e "NetXtreme II BCM57810 10 Gigabit Ethernet" SubVendor: pci 0x103c "Hewlett-Packard Company" SubDevice: pci 0x1798 "Flex-10 10Gb 2-port 530FLB Adapter [Meru]" Revision: 0x11 Driver: "bnx2x" Driver Modules: "bnx2x" Device File: eth0 Features: FCoEOffload = off, iSCSIOffload = off, StorageOnly = off Memory Range: 0xf6000000-0xf67fffff (ro,non-prefetchable) Memory Range: 0xf5800000-0xf5ffffff (ro,non-prefetchable) Memory Range: 0xf57f0000-0xf57fffff (ro,non-prefetchable) Memory Range: 0xf0000000-0xf007ffff (ro,non-prefetchable,disabled) IRQ: 81 (no events) HW Address: 74:46:a0:f5:03:80 Permanent HW Address: 74:46:a0:f5:03:80 Link detected: no Module Alias: "pci:v000014E4d0000168Esv0000103Csd00001798bc02sc00i00" Driver Info #0: Driver Status: bnx2x is active Driver Activation Cmd: "modprobe bnx2x" Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #56 (PCI bridge) # /sbin/ethtool -i eth0 driver: bnx2x version: 1.712.30-0 firmware-version: bc 7.14.62 expansion-rom-version: bus-info: 0000:04:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes supports-priv-flags: yes On 01/16/2018 06:58 PM, Patil, Harish wrote: > > > -----Original Message----- > From: Nirmoy Das <ndas@suse.de<mailto:ndas@suse.de>> > Date: Tuesday, January 16, 2018 at 8:39 AM > To: Harish Patil <Harish.Patil@cavium.com<mailto:Harish.Patil@cavium.com>> > Cc: "Mody, Rasesh" <Rasesh.Mody@cavium.com<mailto:Rasesh.Mody@cavium.com>>, "users@dpdk.org<mailto:users@dpdk.org>" > <users@dpdk.org<mailto:users@dpdk.org>> > Subject: bnx2x_init failed > >> Hi Harish/Rasesh, >> >> I am getting following error on NetXtreme II BCM57810 10 Gigabit >> Ethernet while running dpdk KNI/testpmd application >> >> PMD: bnx2x_reg_write32(): offset=0x0000a3c8 val=0x00000800 >> PMD: bnx2x_init(): Initialization failed, stack notified driver is NOT >> running! >> PMD: bnx2x_dev_start(): bnx2x_init failed (-6) >> EAL: Error - exiting with code: 1 >> Cause: Could not start port0 (-1) >> >> I can't figure out why, its running on 4.4.103-6.38-default and have the >> required firmware. Do you have any suggestion why we are facing this issue >> >> Regards, >> Nirmoy >> -- >> SUSE Linux GmbH, GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB >> 21284 (AG Nürnberg) Maxfeldstr. 5 >> D-90409 Nürnberg / Phone: +49-911-740 18-4 > > > Hi Nirmoy, > Is it testpmd or KNI or both which is not working? > Pls provide the exact cmdline you used to launch the applications? > > Thanks. >> > Nirmoy -- SUSE Linux GmbH, GF: Felix Imendörffer, Jane Smithard, Graham Norton HRB 21284 (AG Nürnberg) Maxfeldstr. 5 D-90409 Nürnberg / Phone: +49-911-740 18-4 ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2018-01-31 20:05 UTC | newest] Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2018-01-16 16:39 [dpdk-users] bnx2x_init failed Nirmoy Das 2018-01-16 17:58 ` Patil, Harish 2018-01-17 10:18 ` Nirmoy Das 2018-01-25 13:30 ` nirmoy das 2018-01-31 20:05 ` Patil, Harish
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).