Re: [dpdk-users] Found 0 usable devices

[Milad Arabi <milad.arabi@gmail.com>]

Thank you

On Mon, May 21, 2018 at 9:37 PM, Wiles, Keith <keith.wiles@intel.com> wrote:

>
>
> > On May 21, 2018, at 11:41 AM, Milad Arabi <milad.arabi@gmail.com> wrote:
> >
> > Since I do not know anything about Eng-Sample NIC then no it's not. It
> is the original Intel network card pass through to CentOS from VMware.
> > Do you think maybe the VMware cause this issue?
>
> Could be, guess its back to google for passthru NICs in VMWare or how to
> set the NIC MAC address  in VMWare.
>
> >
> > On Mon, May 21, 2018 at 8:55 PM, Wiles, Keith <keith.wiles@intel.com>
> wrote:
> >
> >
> >> On May 21, 2018, at 11:16 AM, Milad Arabi <milad.arabi@gmail.com>
> wrote:
> >>
> >> Hi Keith
> >> Thank you for your reply.
> >> Could you please check my output at:
> >> https://asciinema.org/a/182678
> >>
> >> I get this error:
> >> PMD: eth_ixgbe_dev_init(): The EEPROM checksum is not valid: -1
> >
> > Normally that means this is a Eng-Sample NIC, is it?
> >
> > If it is then we have to find someone to program the EPROM to setup the
> NIC.
> >
> > That is about all I know.
> >
> >>
> >> any comment would be appreciated
> >>
> >>
> >> On Mon, May 21, 2018 at 5:26 PM, Wiles, Keith <keith.wiles@intel.com>
> wrote:
> >>
> >>
> >> > On May 21, 2018, at 4:37 AM, Milad Arabi <milad.arabi@gmail.com>
> wrote:
> >> >
> >> > Hi there
> >> > I try to with dpdk 17.08 on centos7.5 with other library,but I got
> this:
> >> >
> >> >> [INFO]  Initializing DPDK. This will take a few seconds...
> >> >> EAL: Detected 16 lcore(s)
> >> >> EAL: Probing VFIO support...
> >> >> EAL: PCI device 0000:0b:00.0 on NUMA socket -1
> >> >> EAL:   Invalid NUMA socket, default to 0
> >> >> EAL:   probe driver: 15ad:7b0 net_vmxnet3
> >> >> EAL: PCI device 0000:13:00.0 on NUMA socket 1
> >> >> EAL:   probe driver: 8086:10fb net_ixgbe
> >> >> EAL: PCI device 0000:13:00.1 on NUMA socket -1
> >> >> EAL:   Invalid NUMA socket, default to 0
> >> >> EAL:   probe driver: 8086:10fb net_ixgbe
> >> >> *[INFO]  Found 0 usable devices:*
> >> >
> >> >
> >> > are these errors come from dpdk? and how I can solve this problem?
> >>
> >> Did you use the dpdk-devbind.py tool in dpdk to bind the device to
> allow DPDK to use the device?
> >>
> >> Also you may have to insmod the igb_uio.ko for pci_uio_generic modules
> in the kernel?
> >>
> >> >
> >> > # ethtool -i ens224f1
> >> >> driver: ixgbe
> >> >> version: 5.3.7
> >> >> firmware-version: 0x80000835, 1.949.0
> >> >> expansion-rom-version:
> >> >> bus-info: 0000:13:00.1
> >> >> supports-statistics: yes
> >> >> supports-test: yes
> >> >> supports-eeprom-access: yes
> >> >> supports-register-dump: yes
> >> >> supports-priv-flags: yes
> >>
> >> Regards,
> >> Keith
> >>
> >>
> >
> > Regards,
> > Keith
> >
> >
>
> Regards,
> Keith
>
>