[dpdk-users] Unable to run l2fwd code

[dpdk-users] Unable to run l2fwd code

[Sagar Singha]

Hi,

I am using VMXNET3 type VM .OS distro=UBUNTU14.04.
My VM is having only one core CPU and 1 GB RAM

I have followed the below process to configure dpdk after downloading the
source code:

1.make config T=x86_64-native-linuxapp-gcc
2.make
3.sudo modprobe uio
sudo insmod build/kmod/igb_uio.ko
modprobe vfio
modprobe uio_pci_generic
modprobe vfio-pci
4.echo 1024 >
/sys/devices/system/node/node0/hugepages/hugepages-2048kB/nr_hugepages
5.sudo mkdir /mnt/huge
sudo mount -t hugetlbfs nodev /mnt/huge
6.echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode
7../usertools/dpdk_devbind.py --bind=vfio-pci --force ens160


after that I am running the below command for running the l2fwd

l2fwd c1 n4 --no-huge -- -p1

Then the error is like below:

EAL: Detected 1 lcore(s)
EAL: Probing VFIO support...
EAL: VFIO support initialized
EAL: Started without hugepages support, physical addresses not available
EAL: PCI device 0000:03:00.0 on NUMA socket -1
EAL:   Invalid NUMA socket, default to 0
EAL:   probe driver: 15ad:7b0 net_vmxnet3
EAL: PCI device 0000:0b:00.0 on NUMA socket -1
EAL:   Invalid NUMA socket, default to 0
EAL:   probe driver: 15ad:7b0 net_vmxnet3
EAL:   using IOMMU type 8 (No-IOMMU)
EAL: Ignore mapping IO port bar(3) addr: 5001
EAL: PCI device 0000:13:00.0 on NUMA socket -1
EAL:   Invalid NUMA socket, default to 0
EAL:   probe driver: 15ad:7b0 net_vmxnet3
MAC updating enabled
Notice: odd number of ports in portmask.
Lcore 0: RX port 0
Initializing port 0... In rte_eth_dev_start
>From return diag
EAL: Error - exiting with code: 1
  Cause: rte_eth_dev_start:err=-22, port=0

Can any one please help here!!
Thanks i advance !!!


-- 
Thanks & Regards,
Sagar Singha
Contact:7416733224
             9475209510

Re: [dpdk-users] Unable to run l2fwd code

[Chris Paquin]

Can you share the output of "../usertools/dpdk_devbind.py -s"?

CHRISTOPHER PAQUIN

SENIOR CLOUD CONSULTANT, RHCE, RHCSA-OSP

Red Hat  <https://www.redhat.com/>

M: 770-906-7646
<https://red.ht/sig>

On Fri, Sep 1, 2017 at 7:16 AM, Sagar Singha <singha.sagar09@gmail.com>
wrote:

> Hi,
>
> I am using VMXNET3 type VM .OS distro=UBUNTU14.04.
> My VM is having only one core CPU and 1 GB RAM
>
> I have followed the below process to configure dpdk after downloading the
> source code:
>
> 1.make config T=x86_64-native-linuxapp-gcc
> 2.make
> 3.sudo modprobe uio
> sudo insmod build/kmod/igb_uio.ko
> modprobe vfio
> modprobe uio_pci_generic
> modprobe vfio-pci
> 4.echo 1024 >
> /sys/devices/system/node/node0/hugepages/hugepages-2048kB/nr_hugepages
> 5.sudo mkdir /mnt/huge
> sudo mount -t hugetlbfs nodev /mnt/huge
> 6.echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode
> 7../usertools/dpdk_devbind.py --bind=vfio-pci --force ens160
>
>
> after that I am running the below command for running the l2fwd
>
> l2fwd c1 n4 --no-huge -- -p1
>
> Then the error is like below:
>
> EAL: Detected 1 lcore(s)
> EAL: Probing VFIO support...
> EAL: VFIO support initialized
> EAL: Started without hugepages support, physical addresses not available
> EAL: PCI device 0000:03:00.0 on NUMA socket -1
> EAL:   Invalid NUMA socket, default to 0
> EAL:   probe driver: 15ad:7b0 net_vmxnet3
> EAL: PCI device 0000:0b:00.0 on NUMA socket -1
> EAL:   Invalid NUMA socket, default to 0
> EAL:   probe driver: 15ad:7b0 net_vmxnet3
> EAL:   using IOMMU type 8 (No-IOMMU)
> EAL: Ignore mapping IO port bar(3) addr: 5001
> EAL: PCI device 0000:13:00.0 on NUMA socket -1
> EAL:   Invalid NUMA socket, default to 0
> EAL:   probe driver: 15ad:7b0 net_vmxnet3
> MAC updating enabled
> Notice: odd number of ports in portmask.
> Lcore 0: RX port 0
> Initializing port 0... In rte_eth_dev_start
> From return diag
> EAL: Error - exiting with code: 1
>   Cause: rte_eth_dev_start:err=-22, port=0
>
> Can any one please help here!!
> Thanks i advance !!!
>
>
> --
> Thanks & Regards,
> Sagar Singha
> Contact:7416733224
>              9475209510
>

Re: [dpdk-users] Unable to run l2fwd code

[Sagar Singha]

I have found that it is failing in function "vmxnet3_dev_start()". when its
trying to activate the device by writing on BAR1 register and reading
from BAR1 register. after that only its failing.

        VMXNET3_WRITE_BAR1_REG(hw, VMXNET3_REG_CMD,
VMXNET3_CMD_ACTIVATE_DEV);
        ret = VMXNET3_READ_BAR1_REG(hw, VMXNET3_REG_CMD);

       /*=====================HERE IT IS FAILING AFTER READING THE
REGISTER===========*/
        if (ret != 0) {
                printf("============sagar:Device activation:
UNSUCCESSFUL==============`\n");
                PMD_INIT_LOG(ERR, "Device activation: UNSUCCESSFUL");
                return -EINVAL;
        }

any configuration issue ??
any solution please !!!!

On Fri, Sep 1, 2017 at 4:46 PM, Sagar Singha <singha.sagar09@gmail.com>
wrote:

> Hi,
>
> I am using VMXNET3 type VM .OS distro=UBUNTU14.04.
> My VM is having only one core CPU and 1 GB RAM
>
> I have followed the below process to configure dpdk after downloading the
> source code:
>
> 1.make config T=x86_64-native-linuxapp-gcc
> 2.make
> 3.sudo modprobe uio
> sudo insmod build/kmod/igb_uio.ko
> modprobe vfio
> modprobe uio_pci_generic
> modprobe vfio-pci
> 4.echo 1024 > /sys/devices/system/node/node0/hugepages/hugepages-
> 2048kB/nr_hugepages
> 5.sudo mkdir /mnt/huge
> sudo mount -t hugetlbfs nodev /mnt/huge
> 6.echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode
> 7../usertools/dpdk_devbind.py --bind=vfio-pci --force ens160
>
>
> after that I am running the below command for running the l2fwd
>
> l2fwd c1 n4 --no-huge -- -p1
>
> Then the error is like below:
>
> EAL: Detected 1 lcore(s)
> EAL: Probing VFIO support...
> EAL: VFIO support initialized
> EAL: Started without hugepages support, physical addresses not available
> EAL: PCI device 0000:03:00.0 on NUMA socket -1
> EAL:   Invalid NUMA socket, default to 0
> EAL:   probe driver: 15ad:7b0 net_vmxnet3
> EAL: PCI device 0000:0b:00.0 on NUMA socket -1
> EAL:   Invalid NUMA socket, default to 0
> EAL:   probe driver: 15ad:7b0 net_vmxnet3
> EAL:   using IOMMU type 8 (No-IOMMU)
> EAL: Ignore mapping IO port bar(3) addr: 5001
> EAL: PCI device 0000:13:00.0 on NUMA socket -1
> EAL:   Invalid NUMA socket, default to 0
> EAL:   probe driver: 15ad:7b0 net_vmxnet3
> MAC updating enabled
> Notice: odd number of ports in portmask.
> Lcore 0: RX port 0
> Initializing port 0... In rte_eth_dev_start
> From return diag
> EAL: Error - exiting with code: 1
>   Cause: rte_eth_dev_start:err=-22, port=0
>
> Can any one please help here!!
> Thanks i advance !!!
>
>
> --
> Thanks & Regards,
> Sagar Singha
> Contact:7416733224
>              9475209510
>
>
>


-- 
Thanks & Regards,
Sagar Singha
Contact:7416733224
             9475209510