DPDK usage discussions
 help / color / mirror / Atom feed
* [dpdk-users] testpmd / SR-IOV RX packets, but TX-errors
@ 2019-10-15 14:01 Bill Michalowski
  2019-10-15 14:26 ` [dpdk-users] [dpdk-dev] " Lance Richardson
  0 siblings, 1 reply; 4+ messages in thread
From: Bill Michalowski @ 2019-10-15 14:01 UTC (permalink / raw)
  To: dev, users

I'm trying run testpmd with SR-IOV, specifically across two VFs.  I see
packets being received successfully by the application but they are not
being transmitted.  They are dropped with the 'TX-errors' counters
incrementing.

However, if I generate the same traffic and the DUT isn't programmed with
SR-IOV, but with testpmd just across PFs, the packets are transmitted just
fine and I don't have any TX-errors.  I'm hoping someone can help me figure
out why the TX packets are being dropped in the SR-IOV case.

testpmd is running in the default "io" mode.

The DUT is a two port Intel xxv710 25G card.  To simplify things, I'm not
actually using a guest, just testpmd across VFs.

*# rpm -qa | grep dpdk*
dpdk-18.11.2-1.el7.x86_64

*# uname -r*
3.10.0-1062.1.2.el7.x86_64

*# cat /etc/redhat-release *
Red Hat Enterprise Linux Server release 7.7 (Maipo)

PFs:

#* ethtool -i p7p1*
driver: i40e
version: 2.10.19.30
firmware-version: 6.80 0x80003d17 18.8.9
expansion-rom-version:
bus-info: 0000:86:00.0

*# ethtool -i p7p2*
driver: i40e
version: 2.10.19.30
firmware-version: 6.80 0x80003d17 18.8.9
expansion-rom-version:
bus-info: 0000:86:00.1

Procedure:

Create VFs:

*#echo 1 > /sys/class/net/p7p1/device/sriov_numvfs*

*#echo 1 > /sys/class/net/p7p2/device/sriov_numvfs*

*# ip l*
4: p7p1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode
DEFAULT group default qlen 1000
    link/ether 3c:fd:fe:b9:c8:a0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state auto, trust
off
5: p7p2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode
DEFAULT group default qlen 1000
    link/ether 3c:fd:fe:b9:c8:a1 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state auto, trust
off
13: p7p1_0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
    link/ether 6a:ff:a3:55:23:4e brd ff:ff:ff:ff:ff:ff
14: p7p2_0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
    link/ether da:a1:1c:c4:6c:e7 brd ff:ff:ff:ff:ff:ff

*# ethtool -i p7p1_0*
driver: iavf
version: 3.7.53
firmware-version: N/A
expansion-rom-version:
bus-info: 0000:86:02.0

*# ethtool -i p7p2_0*
driver: iavf
version: 3.7.53
firmware-version: N/A
expansion-rom-version:
bus-info: 0000:86:0a.0

Set MAC addresses:

*#ip link set p7p1 vf 0 mac a0:b0:c0:d0:e0:f0*
*#ip link set p7p2 vf 0 mac 66:55:44:33:22:11*

Set trust mode:



*#ip link set p7p1 vf 0 trust on#ip link set p7p2 vf 0 trust on*

Unbind iavf from VFs and bind vfio-pci to them:

*# modprobe vfio-pci*
*# dpdk-devbind -u 0000:86:02.0 0000:86:0a.0*
*# dpdk-devbind -b vfio-pci 0000:86:02.0 0000:86:0a.0*
*# dpdk-devbind -s*

Network devices using DPDK-compatible driver
============================================
0000:86:02.0 'Ethernet Virtual Function 700 Series 154c' drv=vfio-pci
unused=iavf
0000:86:0a.0 'Ethernet Virtual Function 700 Series 154c' drv=vfio-pci
unused=iavf

Start testpmd:

#*/usr/bin/testpmd -l 1,3,35 --socket-mem 1024,1024 -n 4 --proc-type auto
--file-prefix testpmd0 -w 0000:86:02.0 -w 0000:86:0a.0 -- --nb-cores=2
--nb-ports=2 --portmask=3 --auto-start --rxq=1 --txq=1 --rxd=2048
--txd=2048 -i*

Starting traffic at the far end, packets are RX successfully on the DUT but
not TX, with many TX-errors:

*testpmd> show port stats all*

  ######################## NIC statistics for port 0
 ########################
  RX-packets: 144132155  RX-missed: 0          RX-bytes:  9224457088
  RX-errors: 0
  RX-nombuf:  0
  TX-packets: 0          TX-errors: 137664400  TX-bytes:  0

  Throughput (since last show)
  Rx-pps:     19000875
  Tx-pps:            0

############################################################################

  ######################## NIC statistics for port 1
 ########################
  RX-packets: 144324307  RX-missed: 0          RX-bytes:  9236754880
  RX-errors: 0
  RX-nombuf:  0
  TX-packets: 0          TX-errors: 137873118  TX-bytes:  0

  Throughput (since last show)
  Rx-pps:     19000772
  Tx-pps:            0

############################################################################

Thanks for any help.

- Bill

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [dpdk-users] [dpdk-dev] testpmd / SR-IOV RX packets, but TX-errors
  2019-10-15 14:01 [dpdk-users] testpmd / SR-IOV RX packets, but TX-errors Bill Michalowski
@ 2019-10-15 14:26 ` Lance Richardson
  2019-10-15 15:03   ` Bill Michalowski
  0 siblings, 1 reply; 4+ messages in thread
From: Lance Richardson @ 2019-10-15 14:26 UTC (permalink / raw)
  To: Bill Michalowski; +Cc: dev, users

Hi Bill,

This is just a guess, but perhaps the transmit drops are due to MAC
anti-spoofing checks?

You could probably prove/disprove by making the packet source MAC
match the transmit VF's MAC.

    Lance


On Tue, Oct 15, 2019 at 10:01 AM Bill Michalowski <bmichalo@redhat.com> wrote:
>
> I'm trying run testpmd with SR-IOV, specifically across two VFs.  I see
> packets being received successfully by the application but they are not
> being transmitted.  They are dropped with the 'TX-errors' counters
> incrementing.
>
> However, if I generate the same traffic and the DUT isn't programmed with
> SR-IOV, but with testpmd just across PFs, the packets are transmitted just
> fine and I don't have any TX-errors.  I'm hoping someone can help me figure
> out why the TX packets are being dropped in the SR-IOV case.
>
> testpmd is running in the default "io" mode.
>
> The DUT is a two port Intel xxv710 25G card.  To simplify things, I'm not
> actually using a guest, just testpmd across VFs.
>
> *# rpm -qa | grep dpdk*
> dpdk-18.11.2-1.el7.x86_64
>
> *# uname -r*
> 3.10.0-1062.1.2.el7.x86_64
>
> *# cat /etc/redhat-release *
> Red Hat Enterprise Linux Server release 7.7 (Maipo)
>
> PFs:
>
> #* ethtool -i p7p1*
> driver: i40e
> version: 2.10.19.30
> firmware-version: 6.80 0x80003d17 18.8.9
> expansion-rom-version:
> bus-info: 0000:86:00.0
>
> *# ethtool -i p7p2*
> driver: i40e
> version: 2.10.19.30
> firmware-version: 6.80 0x80003d17 18.8.9
> expansion-rom-version:
> bus-info: 0000:86:00.1
>
> Procedure:
>
> Create VFs:
>
> *#echo 1 > /sys/class/net/p7p1/device/sriov_numvfs*
>
> *#echo 1 > /sys/class/net/p7p2/device/sriov_numvfs*
>
> *# ip l*
> 4: p7p1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode
> DEFAULT group default qlen 1000
>     link/ether 3c:fd:fe:b9:c8:a0 brd ff:ff:ff:ff:ff:ff
>     vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state auto, trust
> off
> 5: p7p2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode
> DEFAULT group default qlen 1000
>     link/ether 3c:fd:fe:b9:c8:a1 brd ff:ff:ff:ff:ff:ff
>     vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state auto, trust
> off
> 13: p7p1_0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
> DEFAULT group default qlen 1000
>     link/ether 6a:ff:a3:55:23:4e brd ff:ff:ff:ff:ff:ff
> 14: p7p2_0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
> DEFAULT group default qlen 1000
>     link/ether da:a1:1c:c4:6c:e7 brd ff:ff:ff:ff:ff:ff
>
> *# ethtool -i p7p1_0*
> driver: iavf
> version: 3.7.53
> firmware-version: N/A
> expansion-rom-version:
> bus-info: 0000:86:02.0
>
> *# ethtool -i p7p2_0*
> driver: iavf
> version: 3.7.53
> firmware-version: N/A
> expansion-rom-version:
> bus-info: 0000:86:0a.0
>
> Set MAC addresses:
>
> *#ip link set p7p1 vf 0 mac a0:b0:c0:d0:e0:f0*
> *#ip link set p7p2 vf 0 mac 66:55:44:33:22:11*
>
> Set trust mode:
>
>
>
> *#ip link set p7p1 vf 0 trust on#ip link set p7p2 vf 0 trust on*
>
> Unbind iavf from VFs and bind vfio-pci to them:
>
> *# modprobe vfio-pci*
> *# dpdk-devbind -u 0000:86:02.0 0000:86:0a.0*
> *# dpdk-devbind -b vfio-pci 0000:86:02.0 0000:86:0a.0*
> *# dpdk-devbind -s*
>
> Network devices using DPDK-compatible driver
> ============================================
> 0000:86:02.0 'Ethernet Virtual Function 700 Series 154c' drv=vfio-pci
> unused=iavf
> 0000:86:0a.0 'Ethernet Virtual Function 700 Series 154c' drv=vfio-pci
> unused=iavf
>
> Start testpmd:
>
> #*/usr/bin/testpmd -l 1,3,35 --socket-mem 1024,1024 -n 4 --proc-type auto
> --file-prefix testpmd0 -w 0000:86:02.0 -w 0000:86:0a.0 -- --nb-cores=2
> --nb-ports=2 --portmask=3 --auto-start --rxq=1 --txq=1 --rxd=2048
> --txd=2048 -i*
>
> Starting traffic at the far end, packets are RX successfully on the DUT but
> not TX, with many TX-errors:
>
> *testpmd> show port stats all*
>
>   ######################## NIC statistics for port 0
>  ########################
>   RX-packets: 144132155  RX-missed: 0          RX-bytes:  9224457088
>   RX-errors: 0
>   RX-nombuf:  0
>   TX-packets: 0          TX-errors: 137664400  TX-bytes:  0
>
>   Throughput (since last show)
>   Rx-pps:     19000875
>   Tx-pps:            0
>
> ############################################################################
>
>   ######################## NIC statistics for port 1
>  ########################
>   RX-packets: 144324307  RX-missed: 0          RX-bytes:  9236754880
>   RX-errors: 0
>   RX-nombuf:  0
>   TX-packets: 0          TX-errors: 137873118  TX-bytes:  0
>
>   Throughput (since last show)
>   Rx-pps:     19000772
>   Tx-pps:            0
>
> ############################################################################
>
> Thanks for any help.
>
> - Bill

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [dpdk-users] [dpdk-dev] testpmd / SR-IOV RX packets, but TX-errors
  2019-10-15 14:26 ` [dpdk-users] [dpdk-dev] " Lance Richardson
@ 2019-10-15 15:03   ` Bill Michalowski
  2019-10-17 12:33     ` Bill Michalowski
  0 siblings, 1 reply; 4+ messages in thread
From: Bill Michalowski @ 2019-10-15 15:03 UTC (permalink / raw)
  To: Lance Richardson; +Cc: dev, users

Thank you for the suggestion Lance, but that didn't correct the problem.

That being said, I would think that testpmd in "io" mode would just forward
the packets in the SR-IOV case just as it successfully does with testpmd
across the PFs (non SR-IOV) - but I could be wrong.

On Tue, Oct 15, 2019 at 10:26 AM Lance Richardson <
lance.richardson@broadcom.com> wrote:

> Hi Bill,
>
> This is just a guess, but perhaps the transmit drops are due to MAC
> anti-spoofing checks?
>
> You could probably prove/disprove by making the packet source MAC
> match the transmit VF's MAC.
>
>     Lance
>
>
> On Tue, Oct 15, 2019 at 10:01 AM Bill Michalowski <bmichalo@redhat.com>
> wrote:
> >
> > I'm trying run testpmd with SR-IOV, specifically across two VFs.  I see
> > packets being received successfully by the application but they are not
> > being transmitted.  They are dropped with the 'TX-errors' counters
> > incrementing.
> >
> > However, if I generate the same traffic and the DUT isn't programmed with
> > SR-IOV, but with testpmd just across PFs, the packets are transmitted
> just
> > fine and I don't have any TX-errors.  I'm hoping someone can help me
> figure
> > out why the TX packets are being dropped in the SR-IOV case.
> >
> > testpmd is running in the default "io" mode.
> >
> > The DUT is a two port Intel xxv710 25G card.  To simplify things, I'm not
> > actually using a guest, just testpmd across VFs.
> >
> > *# rpm -qa | grep dpdk*
> > dpdk-18.11.2-1.el7.x86_64
> >
> > *# uname -r*
> > 3.10.0-1062.1.2.el7.x86_64
> >
> > *# cat /etc/redhat-release *
> > Red Hat Enterprise Linux Server release 7.7 (Maipo)
> >
> > PFs:
> >
> > #* ethtool -i p7p1*
> > driver: i40e
> > version: 2.10.19.30
> > firmware-version: 6.80 0x80003d17 18.8.9
> > expansion-rom-version:
> > bus-info: 0000:86:00.0
> >
> > *# ethtool -i p7p2*
> > driver: i40e
> > version: 2.10.19.30
> > firmware-version: 6.80 0x80003d17 18.8.9
> > expansion-rom-version:
> > bus-info: 0000:86:00.1
> >
> > Procedure:
> >
> > Create VFs:
> >
> > *#echo 1 > /sys/class/net/p7p1/device/sriov_numvfs*
> >
> > *#echo 1 > /sys/class/net/p7p2/device/sriov_numvfs*
> >
> > *# ip l*
> > 4: p7p1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP
> mode
> > DEFAULT group default qlen 1000
> >     link/ether 3c:fd:fe:b9:c8:a0 brd ff:ff:ff:ff:ff:ff
> >     vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state auto, trust
> > off
> > 5: p7p2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP
> mode
> > DEFAULT group default qlen 1000
> >     link/ether 3c:fd:fe:b9:c8:a1 brd ff:ff:ff:ff:ff:ff
> >     vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state auto, trust
> > off
> > 13: p7p1_0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
> > DEFAULT group default qlen 1000
> >     link/ether 6a:ff:a3:55:23:4e brd ff:ff:ff:ff:ff:ff
> > 14: p7p2_0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
> > DEFAULT group default qlen 1000
> >     link/ether da:a1:1c:c4:6c:e7 brd ff:ff:ff:ff:ff:ff
> >
> > *# ethtool -i p7p1_0*
> > driver: iavf
> > version: 3.7.53
> > firmware-version: N/A
> > expansion-rom-version:
> > bus-info: 0000:86:02.0
> >
> > *# ethtool -i p7p2_0*
> > driver: iavf
> > version: 3.7.53
> > firmware-version: N/A
> > expansion-rom-version:
> > bus-info: 0000:86:0a.0
> >
> > Set MAC addresses:
> >
> > *#ip link set p7p1 vf 0 mac a0:b0:c0:d0:e0:f0*
> > *#ip link set p7p2 vf 0 mac 66:55:44:33:22:11*
> >
> > Set trust mode:
> >
> >
> >
> > *#ip link set p7p1 vf 0 trust on#ip link set p7p2 vf 0 trust on*
> >
> > Unbind iavf from VFs and bind vfio-pci to them:
> >
> > *# modprobe vfio-pci*
> > *# dpdk-devbind -u 0000:86:02.0 0000:86:0a.0*
> > *# dpdk-devbind -b vfio-pci 0000:86:02.0 0000:86:0a.0*
> > *# dpdk-devbind -s*
> >
> > Network devices using DPDK-compatible driver
> > ============================================
> > 0000:86:02.0 'Ethernet Virtual Function 700 Series 154c' drv=vfio-pci
> > unused=iavf
> > 0000:86:0a.0 'Ethernet Virtual Function 700 Series 154c' drv=vfio-pci
> > unused=iavf
> >
> > Start testpmd:
> >
> > #*/usr/bin/testpmd -l 1,3,35 --socket-mem 1024,1024 -n 4 --proc-type auto
> > --file-prefix testpmd0 -w 0000:86:02.0 -w 0000:86:0a.0 -- --nb-cores=2
> > --nb-ports=2 --portmask=3 --auto-start --rxq=1 --txq=1 --rxd=2048
> > --txd=2048 -i*
> >
> > Starting traffic at the far end, packets are RX successfully on the DUT
> but
> > not TX, with many TX-errors:
> >
> > *testpmd> show port stats all*
> >
> >   ######################## NIC statistics for port 0
> >  ########################
> >   RX-packets: 144132155  RX-missed: 0          RX-bytes:  9224457088
> >   RX-errors: 0
> >   RX-nombuf:  0
> >   TX-packets: 0          TX-errors: 137664400  TX-bytes:  0
> >
> >   Throughput (since last show)
> >   Rx-pps:     19000875
> >   Tx-pps:            0
> >
> >
> ############################################################################
> >
> >   ######################## NIC statistics for port 1
> >  ########################
> >   RX-packets: 144324307  RX-missed: 0          RX-bytes:  9236754880
> >   RX-errors: 0
> >   RX-nombuf:  0
> >   TX-packets: 0          TX-errors: 137873118  TX-bytes:  0
> >
> >   Throughput (since last show)
> >   Rx-pps:     19000772
> >   Tx-pps:            0
> >
> >
> ############################################################################
> >
> > Thanks for any help.
> >
> > - Bill
>

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: [dpdk-users] [dpdk-dev] testpmd / SR-IOV RX packets, but TX-errors
  2019-10-15 15:03   ` Bill Michalowski
@ 2019-10-17 12:33     ` Bill Michalowski
  0 siblings, 0 replies; 4+ messages in thread
From: Bill Michalowski @ 2019-10-17 12:33 UTC (permalink / raw)
  To: Lance Richardson; +Cc: dev, users

Solved... had to disable spoof checking:

ip link set p7p1 vf 0 spoofchk off
ip link set p7p2 vf 0 spoofchk off

Thank you!

On Tue, Oct 15, 2019 at 11:03 AM Bill Michalowski <bmichalo@redhat.com>
wrote:

> Thank you for the suggestion Lance, but that didn't correct the problem.
>
> That being said, I would think that testpmd in "io" mode would just
> forward the packets in the SR-IOV case just as it successfully does with
> testpmd across the PFs (non SR-IOV) - but I could be wrong.
>
> On Tue, Oct 15, 2019 at 10:26 AM Lance Richardson <
> lance.richardson@broadcom.com> wrote:
>
>> Hi Bill,
>>
>> This is just a guess, but perhaps the transmit drops are due to MAC
>> anti-spoofing checks?
>>
>> You could probably prove/disprove by making the packet source MAC
>> match the transmit VF's MAC.
>>
>>     Lance
>>
>>
>> On Tue, Oct 15, 2019 at 10:01 AM Bill Michalowski <bmichalo@redhat.com>
>> wrote:
>> >
>> > I'm trying run testpmd with SR-IOV, specifically across two VFs.  I see
>> > packets being received successfully by the application but they are not
>> > being transmitted.  They are dropped with the 'TX-errors' counters
>> > incrementing.
>> >
>> > However, if I generate the same traffic and the DUT isn't programmed
>> with
>> > SR-IOV, but with testpmd just across PFs, the packets are transmitted
>> just
>> > fine and I don't have any TX-errors.  I'm hoping someone can help me
>> figure
>> > out why the TX packets are being dropped in the SR-IOV case.
>> >
>> > testpmd is running in the default "io" mode.
>> >
>> > The DUT is a two port Intel xxv710 25G card.  To simplify things, I'm
>> not
>> > actually using a guest, just testpmd across VFs.
>> >
>> > *# rpm -qa | grep dpdk*
>> > dpdk-18.11.2-1.el7.x86_64
>> >
>> > *# uname -r*
>> > 3.10.0-1062.1.2.el7.x86_64
>> >
>> > *# cat /etc/redhat-release *
>> > Red Hat Enterprise Linux Server release 7.7 (Maipo)
>> >
>> > PFs:
>> >
>> > #* ethtool -i p7p1*
>> > driver: i40e
>> > version: 2.10.19.30
>> > firmware-version: 6.80 0x80003d17 18.8.9
>> > expansion-rom-version:
>> > bus-info: 0000:86:00.0
>> >
>> > *# ethtool -i p7p2*
>> > driver: i40e
>> > version: 2.10.19.30
>> > firmware-version: 6.80 0x80003d17 18.8.9
>> > expansion-rom-version:
>> > bus-info: 0000:86:00.1
>> >
>> > Procedure:
>> >
>> > Create VFs:
>> >
>> > *#echo 1 > /sys/class/net/p7p1/device/sriov_numvfs*
>> >
>> > *#echo 1 > /sys/class/net/p7p2/device/sriov_numvfs*
>> >
>> > *# ip l*
>> > 4: p7p1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP
>> mode
>> > DEFAULT group default qlen 1000
>> >     link/ether 3c:fd:fe:b9:c8:a0 brd ff:ff:ff:ff:ff:ff
>> >     vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state auto,
>> trust
>> > off
>> > 5: p7p2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP
>> mode
>> > DEFAULT group default qlen 1000
>> >     link/ether 3c:fd:fe:b9:c8:a1 brd ff:ff:ff:ff:ff:ff
>> >     vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state auto,
>> trust
>> > off
>> > 13: p7p1_0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
>> > DEFAULT group default qlen 1000
>> >     link/ether 6a:ff:a3:55:23:4e brd ff:ff:ff:ff:ff:ff
>> > 14: p7p2_0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
>> > DEFAULT group default qlen 1000
>> >     link/ether da:a1:1c:c4:6c:e7 brd ff:ff:ff:ff:ff:ff
>> >
>> > *# ethtool -i p7p1_0*
>> > driver: iavf
>> > version: 3.7.53
>> > firmware-version: N/A
>> > expansion-rom-version:
>> > bus-info: 0000:86:02.0
>> >
>> > *# ethtool -i p7p2_0*
>> > driver: iavf
>> > version: 3.7.53
>> > firmware-version: N/A
>> > expansion-rom-version:
>> > bus-info: 0000:86:0a.0
>> >
>> > Set MAC addresses:
>> >
>> > *#ip link set p7p1 vf 0 mac a0:b0:c0:d0:e0:f0*
>> > *#ip link set p7p2 vf 0 mac 66:55:44:33:22:11*
>> >
>> > Set trust mode:
>> >
>> >
>> >
>> > *#ip link set p7p1 vf 0 trust on#ip link set p7p2 vf 0 trust on*
>> >
>> > Unbind iavf from VFs and bind vfio-pci to them:
>> >
>> > *# modprobe vfio-pci*
>> > *# dpdk-devbind -u 0000:86:02.0 0000:86:0a.0*
>> > *# dpdk-devbind -b vfio-pci 0000:86:02.0 0000:86:0a.0*
>> > *# dpdk-devbind -s*
>> >
>> > Network devices using DPDK-compatible driver
>> > ============================================
>> > 0000:86:02.0 'Ethernet Virtual Function 700 Series 154c' drv=vfio-pci
>> > unused=iavf
>> > 0000:86:0a.0 'Ethernet Virtual Function 700 Series 154c' drv=vfio-pci
>> > unused=iavf
>> >
>> > Start testpmd:
>> >
>> > #*/usr/bin/testpmd -l 1,3,35 --socket-mem 1024,1024 -n 4 --proc-type
>> auto
>> > --file-prefix testpmd0 -w 0000:86:02.0 -w 0000:86:0a.0 -- --nb-cores=2
>> > --nb-ports=2 --portmask=3 --auto-start --rxq=1 --txq=1 --rxd=2048
>> > --txd=2048 -i*
>> >
>> > Starting traffic at the far end, packets are RX successfully on the DUT
>> but
>> > not TX, with many TX-errors:
>> >
>> > *testpmd> show port stats all*
>> >
>> >   ######################## NIC statistics for port 0
>> >  ########################
>> >   RX-packets: 144132155  RX-missed: 0          RX-bytes:  9224457088
>> >   RX-errors: 0
>> >   RX-nombuf:  0
>> >   TX-packets: 0          TX-errors: 137664400  TX-bytes:  0
>> >
>> >   Throughput (since last show)
>> >   Rx-pps:     19000875
>> >   Tx-pps:            0
>> >
>> >
>> ############################################################################
>> >
>> >   ######################## NIC statistics for port 1
>> >  ########################
>> >   RX-packets: 144324307  RX-missed: 0          RX-bytes:  9236754880
>> >   RX-errors: 0
>> >   RX-nombuf:  0
>> >   TX-packets: 0          TX-errors: 137873118  TX-bytes:  0
>> >
>> >   Throughput (since last show)
>> >   Rx-pps:     19000772
>> >   Tx-pps:            0
>> >
>> >
>> ############################################################################
>> >
>> > Thanks for any help.
>> >
>> > - Bill
>>
>

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~2019-10-17 12:33 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-15 14:01 [dpdk-users] testpmd / SR-IOV RX packets, but TX-errors Bill Michalowski
2019-10-15 14:26 ` [dpdk-users] [dpdk-dev] " Lance Richardson
2019-10-15 15:03   ` Bill Michalowski
2019-10-17 12:33     ` Bill Michalowski

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).