From: Aaron Hughes <hughesac@gmail.com>
To: users@dpdk.org, masutani.hitoshi@lab.ntt.co.jp
Subject: Re: [dpdk-users] Failed to initialize one specific port of X710-DA4 in i40e pmd
Date: Fri, 24 Aug 2018 16:55:12 +0000 [thread overview]
Message-ID: <CAP=pv7MCktADmtqVjYADdB6ZuN9Y=Gp7EF4UN=_4v+_h8tfkKA@mail.gmail.com> (raw)
In-Reply-To: <CAP=pv7Or=wFxv1joOL5r9ZyXF-u9vccTAYuLuF-RsfW_JNU_CQ@mail.gmail.com>
Does anyone know what tool can be used to configure/view the settings for
the XL710? I would like to view the DCB and TC settings. Based on the
i40e README you can't use dcbtool and I don't see anyway to do it with
ethtool. One of the ports on the XL710 is working for me but the other one
is showing the error about the TC map.
I see this message from the kernel's i40e driver for the port that isn't
working with DPDK:
Non-contiguous TC - Disabling DCB
https://downloadmirror.intel.com/25282/eng/README.txt
On Thu, Aug 23, 2018 at 7:54 PM Aaron Hughes <hughesac@gmail.com> wrote:
> Hi Hitoshi,
>
> Did you ever figure out a solution to your problem with the X710? I'm
> seeing the same problem with an XL710 using DPDK version 17.05 on Redhat
> 7.5:
>
> validate_tcmap_parameter(): Enabled TC map 0x80 not applicable to HW
> support 0x1
> i40e_vsi_setup(): Failed to update TC bandwidth
> i40e_pf_setup(): Setup of main vsi failed
> eth_i40e_dev_init(): Failed to setup pf switch: -63
>
> Thanks,
> Aaron
>
> I am facing a failure of dpdk(16.11.3) initialization with testpmd
>> using i40e pmd on a specific physical port of X710-DA4.
>>
>> Without such specific port, testpmd can run successfully.
>>
>> My server box has two X710-DA4 cards and
>> these two cards have the same failure.
>>
>> To clarify whether it is caused by hardware failure or
>> by the lack of appropriate nic configuration,
>> the following build options of dpdk are enabled.
>>
>> --------------
>> CONFIG_RTE_LIBRTE_ETHDEV_DEBUG=y
>> CONFIG_RTE_LIBRTE_I40E_DEBUG_INIT=y
>> CONFIG_RTE_LIBRTE_I40E_DEBUG_DRIVER=y
>> --------------
>>
>> My server box spec. is as follows :
>>
>> CPU : Intel(R) Xeon(R) Gold 6136
>> MEMORY : 128GB (16G x 8)
>> Motherboard: SYS-1029U-TR4
>> NIC1 : I350 x 4 (onboard nic)
>> NIC2 : XL710 dual
>> NIC3 : X710-DA4
>> NIC4 : X710-DA4
>> ------------------------------------------------------------
>> OS : ubnutu 16.04.3 LTS(linux-image-4.4.0-87-generic)
>> DPDK : 16.11.3
>>
>> testpmd's boot message is as follows :
>> --------------------------------------------
>> $ sudo ./testpmd -- -i
>>
>> EAL: Detected 24 lcore(s)
>> EAL: Probing VFIO support...
>> EAL: PCI device 0000:18:00.0 on NUMA socket 0
>> EAL: probe driver: 8086:1521 net_e1000_igb
>> EAL: PCI device 0000:18:00.1 on NUMA socket 0
>> EAL: probe driver: 8086:1521 net_e1000_igb
>> EAL: PCI device 0000:18:00.2 on NUMA socket 0
>> EAL: probe driver: 8086:1521 net_e1000_igb
>> EAL: PCI device 0000:18:00.3 on NUMA socket 0
>> EAL: probe driver: 8086:1521 net_e1000_igb
>> EAL: PCI device 0000:86:00.0 on NUMA socket 1
>> EAL: probe driver: 8086:1583 net_i40e
>> EAL: PCI device 0000:86:00.1 on NUMA socket 1
>> EAL: probe driver: 8086:1583 net_i40e
>> EAL: PCI device 0000:af:00.0 on NUMA socket 1
>> EAL: probe driver: 8086:1572 net_i40e
>> PMD: i40e_set_symmetric_hash_enable_per_port(): Symmetric hash has
>> already been disabled
>> PMD: eth_i40e_dev_init(): FW 5.0 API 1.5 NVM 05.00.05 eetrack 80002919
>> PMD: i40e_update_default_filter_setting(): Cannot remove the default
>> macvlan filter
>> PMD: i40e_pf_setup(): i40e_vsi_setup finished
>> PMD: i40e_pf_setup(): Hardware capability of hash lookup table size: 512
>>
>> PMD: i40e_update_flow_control(): Link auto negotiation not completed
>> EAL: PCI device 0000:af:00.1 on NUMA socket 1
>> EAL: probe driver: 8086:1572 net_i40e
>> EAL: PCI device 0000:af:00.2 on NUMA socket 1
>> EAL: probe driver: 8086:1572 net_i40e
>> PMD: i40e_set_symmetric_hash_enable_per_port(): Symmetric hash has
>> already been disabled
>> PMD: eth_i40e_dev_init(): FW 5.0 API 1.5 NVM 05.00.05 eetrack 80002919
>> PMD: validate_tcmap_parameter(): Enabled TC map 0x80 not applicable to
>> HW support 0x1
>> PMD: i40e_vsi_setup(): Failed to update TC bandwidth
>> PMD: i40e_pf_setup(): Setup of main vsi failed
>> PMD: eth_i40e_dev_init(): Failed to setup pf switch: -63
>> rte_eth_dev_pci_probe: driver net_i40e: eth_dev_init(vendor_id=0x8086
>> device_id=0x1572) failed
>> EAL: Error - exiting with code: 1
>> Cause: Requested device 0000:af:00.2 cannot be used
>> ---------------------------
>>
>> If you have solutions, could you tell me how this problem can be resolved ?
>>
>> Regards,
>> Hitoshi
>>
>>
next prev parent reply other threads:[~2018-08-24 16:55 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-08-23 19:54 Aaron Hughes
2018-08-23 22:25 ` Hitoshi Masutani
2018-08-24 16:55 ` Aaron Hughes [this message]
2019-12-20 13:53 ` Ananda Sathyanarayana
-- strict thread matches above, loose matches on Subject: below --
2018-03-23 5:50 Hitoshi Masutani
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAP=pv7MCktADmtqVjYADdB6ZuN9Y=Gp7EF4UN=_4v+_h8tfkKA@mail.gmail.com' \
--to=hughesac@gmail.com \
--cc=masutani.hitoshi@lab.ntt.co.jp \
--cc=users@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).