DPDK patches and discussions
 help / color / mirror / Atom feed
* Re: [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close
  2019-07-08 11:43 [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close Xiao Zhang
@ 2019-07-08  8:35 ` Zhao1, Wei
  2019-07-09  2:46   ` Zhang, Xiao
  0 siblings, 1 reply; 3+ messages in thread
From: Zhao1, Wei @ 2019-07-08  8:35 UTC (permalink / raw)
  To: Zhang, Xiao, dev; +Cc: Zhang, Xiao

Hi, xiao

> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Xiao Zhang
> Sent: Monday, July 8, 2019 7:44 PM
> To: dev@dpdk.org
> Cc: Zhang, Xiao <xiao.zhang@intel.com>
> Subject: [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close
> 
> Unit hang may occur if multiple descriptors are available in the rings during
> reset or close. This state can be detected by configure status by bit 8 in register.
> If the bit is set and there are pending descriptors in one of the rings, we must
> flush them before reset or close.
> 
> Signed-off-by: Xiao Zhang <xiao.zhang@intel.com>
> ---
>  drivers/net/e1000/base/e1000_ich8lan.h |  1 +
>  drivers/net/e1000/e1000_ethdev.h       |  1 +
>  drivers/net/e1000/igb_ethdev.c         |  4 ++
>  drivers/net/e1000/igb_rxtx.c           | 96
> ++++++++++++++++++++++++++++++++++
>  4 files changed, 102 insertions(+)
> 
> diff --git a/drivers/net/e1000/base/e1000_ich8lan.h
> b/drivers/net/e1000/base/e1000_ich8lan.h
> index bc4ed1d..1f2a3f8 100644
> --- a/drivers/net/e1000/base/e1000_ich8lan.h
> +++ b/drivers/net/e1000/base/e1000_ich8lan.h
> @@ -120,6 +120,7 @@ POSSIBILITY OF SUCH DAMAGE.
>  #define E1000_FEXTNVM7_SIDE_CLK_UNGATE	0x00000004
>  #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT)
>  #define E1000_FEXTNVM7_DISABLE_SMB_PERST	0x00000020
> +#define E1000_FEXTNVM7_NEED_DESCRING_FLUSH	0x00000100
>  #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */
>  #define E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS	0x00000800
>  #define E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS	0x00001000
> diff --git a/drivers/net/e1000/e1000_ethdev.h
> b/drivers/net/e1000/e1000_ethdev.h
> index 67acb73..3451979 100644
> --- a/drivers/net/e1000/e1000_ethdev.h
> +++ b/drivers/net/e1000/e1000_ethdev.h
> @@ -522,5 +522,6 @@ int igb_action_rss_same(const struct
> rte_flow_action_rss *comp,  int igb_config_rss_filter(struct rte_eth_dev *dev,
>  			struct igb_rte_flow_rss_conf *conf,
>  			bool add);
> +void igb_flush_desc_rings(struct rte_eth_dev *dev);
> 
>  #endif /* _E1000_ETHDEV_H_ */
> diff --git a/drivers/net/e1000/igb_ethdev.c b/drivers/net/e1000/igb_ethdev.c
> index 3ee28cf..845101b 100644
> --- a/drivers/net/e1000/igb_ethdev.c
> +++ b/drivers/net/e1000/igb_ethdev.c
> @@ -1589,6 +1589,10 @@ eth_igb_close(struct rte_eth_dev *dev)
>  	eth_igb_stop(dev);
>  	adapter->stopped = 1;
> 
> +	/* Flush desc rings for i219 */
> +	if (hw->mac.type >= e1000_pch_spt)
> +		igb_flush_desc_rings(dev);
> +
>  	e1000_phy_hw_reset(hw);
>  	igb_release_manageability(hw);
>  	igb_hw_control_release(hw);
> diff --git a/drivers/net/e1000/igb_rxtx.c b/drivers/net/e1000/igb_rxtx.c index
> c5606de..33eeb4e 100644
> --- a/drivers/net/e1000/igb_rxtx.c
> +++ b/drivers/net/e1000/igb_rxtx.c
> @@ -18,6 +18,7 @@
>  #include <rte_log.h>
>  #include <rte_debug.h>
>  #include <rte_pci.h>
> +#include <rte_bus_pci.h>
>  #include <rte_memory.h>
>  #include <rte_memcpy.h>
>  #include <rte_memzone.h>
> @@ -63,6 +64,9 @@
>  #define IGB_TX_OFFLOAD_NOTSUP_MASK \
>  		(PKT_TX_OFFLOAD_MASK ^ IGB_TX_OFFLOAD_MASK)
> 
> +/* PCI offset for querying descriptor ring status*/
> +#define PCICFG_DESC_RING_STATUS           0xE4
> +
>  /**
>   * Structure associated with each descriptor of the RX ring of a RX queue.
>   */
> @@ -2962,3 +2966,95 @@ igb_config_rss_filter(struct rte_eth_dev *dev,
> 
>  	return 0;
>  }
> +
> +static void e1000_flush_tx_ring(struct rte_eth_dev *dev) {
> +	struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data-
> >dev_private);
> +	volatile union e1000_adv_tx_desc *tx_desc;
> +	uint32_t tdt, tctl, txd_lower = E1000_TXD_CMD_IFCS;
> +	uint16_t size = 512;
> +	struct igb_tx_queue *txq;
> +
> +	if (dev->data->tx_queues == NULL)
> +		return;
> +	txq = dev->data->tx_queues[0];
> +
> +	tctl = E1000_READ_REG(hw, E1000_TCTL);
> +	E1000_WRITE_REG(hw, E1000_TCTL, tctl | E1000_TCTL_EN);
> +	tdt = E1000_READ_REG(hw, E1000_TDT(0));
> +	if (tdt != txq->tx_tail)
> +		return;
> +	tx_desc = txq->tx_ring;
> +	tx_desc->read.buffer_addr = txq->tx_ring_phys_addr;
> +	tx_desc->read.cmd_type_len = rte_cpu_to_le_32(txd_lower | size);
> +	tx_desc->read.olinfo_status = 0;
> +
> +	rte_wmb();
> +	txq->tx_tail++;
> +	if (txq->tx_tail == txq->nb_tx_desc)
> +		txq->tx_tail = 0;
> +	rte_io_wmb();
> +	E1000_WRITE_REG(hw, E1000_TDT(0), txq->tx_tail);
> +	usec_delay(250);
> +}
> +
> +static void e1000_flush_rx_ring(struct rte_eth_dev *dev) {
> +	uint32_t rctl, rxdctl;
> +	struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data-
> >dev_private);
> +
> +	rctl = E1000_READ_REG(hw, E1000_RCTL);
> +	E1000_WRITE_REG(hw, E1000_TCTL, rctl & ~E1000_RCTL_EN);
> +	E1000_WRITE_FLUSH(hw);
> +	usec_delay(150);
> +
> +	rxdctl = E1000_READ_REG(hw, E1000_RXDCTL(0));
> +	/* zero the lower 14 bits (prefetch and host thresholds) */
> +	rxdctl &= 0xffffc000;
> +
> +	/* update thresholds: prefetch threshold to 31, host threshold to 1
> +	 * and make sure the granularity is "descriptors" and not "cache lines"
> +	 */
> +	rxdctl |= (0x1F | (1UL << 8) | E1000_RXDCTL_THRESH_UNIT_DESC);
> +
> +	E1000_WRITE_REG(hw, E1000_RXDCTL(0), rxdctl);
> +	/* momentarily enable the RX ring for the changes to take effect */
> +	E1000_WRITE_REG(hw, E1000_RCTL, rctl | E1000_RCTL_EN);
> +	E1000_WRITE_FLUSH(hw);
> +	usec_delay(150);
> +	E1000_WRITE_REG(hw, E1000_RCTL, rctl & ~E1000_RCTL_EN); }
> +

In dpdk driver, it may enable and use many queues, so why do we only 
Process tx and rx queue 0,  ring for other queues not need to handle?






> +/**
> + * igb_flush_desc_rings - remove all descriptors from the descriptor
> +rings
> + *
> + * In i219, the descriptor rings must be emptied before
> +resetting/closing the
> + * HW. Failure to do this will cause the HW to enter a unit hang state
> +which
> + * can only be released by PCI reset on the device
> + *
> + */
> +
> +void igb_flush_desc_rings(struct rte_eth_dev *dev) {
> +	uint32_t fextnvm11, tdlen;
> +	struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data-
> >dev_private);
> +	struct rte_pci_device *pci_dev = RTE_ETH_DEV_TO_PCI(dev);
> +	uint32_t hang_state = 0;
> +
> +	fextnvm11 = E1000_READ_REG(hw, E1000_FEXTNVM11);
> +	E1000_WRITE_REG(hw, E1000_FEXTNVM11,
> +			fextnvm11 | E1000_FEXTNVM11_DISABLE_MULR_FIX);
> +	tdlen = E1000_READ_REG(hw, E1000_TDLEN(0));
> +	rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state),
> +				PCICFG_DESC_RING_STATUS);
> +
> +	/* do nothing if we're not in faulty state, or if the queue is empty */
> +	if ((hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) &&
> tdlen) {
> +		/* flush desc ring */
> +		e1000_flush_tx_ring(dev);
> +		rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state),
> +					PCICFG_DESC_RING_STATUS);
> +		if (hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH)
> +			e1000_flush_rx_ring(dev);
> +	}
> +}
> --
> 2.7.4


^ permalink raw reply	[flat|nested] 3+ messages in thread

* [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close
@ 2019-07-08 11:43 Xiao Zhang
  2019-07-08  8:35 ` Zhao1, Wei
  0 siblings, 1 reply; 3+ messages in thread
From: Xiao Zhang @ 2019-07-08 11:43 UTC (permalink / raw)
  To: dev; +Cc: Xiao Zhang

Unit hang may occur if multiple descriptors are available in the rings
during reset or close. This state can be detected by configure status
by bit 8 in register. If the bit is set and there are pending descriptors
in one of the rings, we must flush them before reset or close.

Signed-off-by: Xiao Zhang <xiao.zhang@intel.com>
---
 drivers/net/e1000/base/e1000_ich8lan.h |  1 +
 drivers/net/e1000/e1000_ethdev.h       |  1 +
 drivers/net/e1000/igb_ethdev.c         |  4 ++
 drivers/net/e1000/igb_rxtx.c           | 96 ++++++++++++++++++++++++++++++++++
 4 files changed, 102 insertions(+)

diff --git a/drivers/net/e1000/base/e1000_ich8lan.h b/drivers/net/e1000/base/e1000_ich8lan.h
index bc4ed1d..1f2a3f8 100644
--- a/drivers/net/e1000/base/e1000_ich8lan.h
+++ b/drivers/net/e1000/base/e1000_ich8lan.h
@@ -120,6 +120,7 @@ POSSIBILITY OF SUCH DAMAGE.
 #define E1000_FEXTNVM7_SIDE_CLK_UNGATE	0x00000004
 #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT)
 #define E1000_FEXTNVM7_DISABLE_SMB_PERST	0x00000020
+#define E1000_FEXTNVM7_NEED_DESCRING_FLUSH	0x00000100
 #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */
 #define E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS	0x00000800
 #define E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS	0x00001000
diff --git a/drivers/net/e1000/e1000_ethdev.h b/drivers/net/e1000/e1000_ethdev.h
index 67acb73..3451979 100644
--- a/drivers/net/e1000/e1000_ethdev.h
+++ b/drivers/net/e1000/e1000_ethdev.h
@@ -522,5 +522,6 @@ int igb_action_rss_same(const struct rte_flow_action_rss *comp,
 int igb_config_rss_filter(struct rte_eth_dev *dev,
 			struct igb_rte_flow_rss_conf *conf,
 			bool add);
+void igb_flush_desc_rings(struct rte_eth_dev *dev);
 
 #endif /* _E1000_ETHDEV_H_ */
diff --git a/drivers/net/e1000/igb_ethdev.c b/drivers/net/e1000/igb_ethdev.c
index 3ee28cf..845101b 100644
--- a/drivers/net/e1000/igb_ethdev.c
+++ b/drivers/net/e1000/igb_ethdev.c
@@ -1589,6 +1589,10 @@ eth_igb_close(struct rte_eth_dev *dev)
 	eth_igb_stop(dev);
 	adapter->stopped = 1;
 
+	/* Flush desc rings for i219 */
+	if (hw->mac.type >= e1000_pch_spt)
+		igb_flush_desc_rings(dev);
+
 	e1000_phy_hw_reset(hw);
 	igb_release_manageability(hw);
 	igb_hw_control_release(hw);
diff --git a/drivers/net/e1000/igb_rxtx.c b/drivers/net/e1000/igb_rxtx.c
index c5606de..33eeb4e 100644
--- a/drivers/net/e1000/igb_rxtx.c
+++ b/drivers/net/e1000/igb_rxtx.c
@@ -18,6 +18,7 @@
 #include <rte_log.h>
 #include <rte_debug.h>
 #include <rte_pci.h>
+#include <rte_bus_pci.h>
 #include <rte_memory.h>
 #include <rte_memcpy.h>
 #include <rte_memzone.h>
@@ -63,6 +64,9 @@
 #define IGB_TX_OFFLOAD_NOTSUP_MASK \
 		(PKT_TX_OFFLOAD_MASK ^ IGB_TX_OFFLOAD_MASK)
 
+/* PCI offset for querying descriptor ring status*/
+#define PCICFG_DESC_RING_STATUS           0xE4
+
 /**
  * Structure associated with each descriptor of the RX ring of a RX queue.
  */
@@ -2962,3 +2966,95 @@ igb_config_rss_filter(struct rte_eth_dev *dev,
 
 	return 0;
 }
+
+static void e1000_flush_tx_ring(struct rte_eth_dev *dev)
+{
+	struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data->dev_private);
+	volatile union e1000_adv_tx_desc *tx_desc;
+	uint32_t tdt, tctl, txd_lower = E1000_TXD_CMD_IFCS;
+	uint16_t size = 512;
+	struct igb_tx_queue *txq;
+
+	if (dev->data->tx_queues == NULL)
+		return;
+	txq = dev->data->tx_queues[0];
+
+	tctl = E1000_READ_REG(hw, E1000_TCTL);
+	E1000_WRITE_REG(hw, E1000_TCTL, tctl | E1000_TCTL_EN);
+	tdt = E1000_READ_REG(hw, E1000_TDT(0));
+	if (tdt != txq->tx_tail)
+		return;
+	tx_desc = txq->tx_ring;
+	tx_desc->read.buffer_addr = txq->tx_ring_phys_addr;
+	tx_desc->read.cmd_type_len = rte_cpu_to_le_32(txd_lower | size);
+	tx_desc->read.olinfo_status = 0;
+
+	rte_wmb();
+	txq->tx_tail++;
+	if (txq->tx_tail == txq->nb_tx_desc)
+		txq->tx_tail = 0;
+	rte_io_wmb();
+	E1000_WRITE_REG(hw, E1000_TDT(0), txq->tx_tail);
+	usec_delay(250);
+}
+
+static void e1000_flush_rx_ring(struct rte_eth_dev *dev)
+{
+	uint32_t rctl, rxdctl;
+	struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data->dev_private);
+
+	rctl = E1000_READ_REG(hw, E1000_RCTL);
+	E1000_WRITE_REG(hw, E1000_TCTL, rctl & ~E1000_RCTL_EN);
+	E1000_WRITE_FLUSH(hw);
+	usec_delay(150);
+
+	rxdctl = E1000_READ_REG(hw, E1000_RXDCTL(0));
+	/* zero the lower 14 bits (prefetch and host thresholds) */
+	rxdctl &= 0xffffc000;
+
+	/* update thresholds: prefetch threshold to 31, host threshold to 1
+	 * and make sure the granularity is "descriptors" and not "cache lines"
+	 */
+	rxdctl |= (0x1F | (1UL << 8) | E1000_RXDCTL_THRESH_UNIT_DESC);
+
+	E1000_WRITE_REG(hw, E1000_RXDCTL(0), rxdctl);
+	/* momentarily enable the RX ring for the changes to take effect */
+	E1000_WRITE_REG(hw, E1000_RCTL, rctl | E1000_RCTL_EN);
+	E1000_WRITE_FLUSH(hw);
+	usec_delay(150);
+	E1000_WRITE_REG(hw, E1000_RCTL, rctl & ~E1000_RCTL_EN);
+}
+
+/**
+ * igb_flush_desc_rings - remove all descriptors from the descriptor rings
+ *
+ * In i219, the descriptor rings must be emptied before resetting/closing the
+ * HW. Failure to do this will cause the HW to enter a unit hang state which
+ * can only be released by PCI reset on the device
+ *
+ */
+
+void igb_flush_desc_rings(struct rte_eth_dev *dev)
+{
+	uint32_t fextnvm11, tdlen;
+	struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data->dev_private);
+	struct rte_pci_device *pci_dev = RTE_ETH_DEV_TO_PCI(dev);
+	uint32_t hang_state = 0;
+
+	fextnvm11 = E1000_READ_REG(hw, E1000_FEXTNVM11);
+	E1000_WRITE_REG(hw, E1000_FEXTNVM11,
+			fextnvm11 | E1000_FEXTNVM11_DISABLE_MULR_FIX);
+	tdlen = E1000_READ_REG(hw, E1000_TDLEN(0));
+	rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state),
+				PCICFG_DESC_RING_STATUS);
+
+	/* do nothing if we're not in faulty state, or if the queue is empty */
+	if ((hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) && tdlen) {
+		/* flush desc ring */
+		e1000_flush_tx_ring(dev);
+		rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state),
+					PCICFG_DESC_RING_STATUS);
+		if (hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH)
+			e1000_flush_rx_ring(dev);
+	}
+}
-- 
2.7.4


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close
  2019-07-08  8:35 ` Zhao1, Wei
@ 2019-07-09  2:46   ` Zhang, Xiao
  0 siblings, 0 replies; 3+ messages in thread
From: Zhang, Xiao @ 2019-07-09  2:46 UTC (permalink / raw)
  To: Zhao1, Wei, dev

Hi Wei,

Thanks for your point. I219 supports dual rx and tx queues, I will update the fix.

BR,
Xiao
> -----Original Message-----
> From: Zhao1, Wei
> Sent: Monday, July 8, 2019 4:36 PM
> To: Zhang, Xiao <xiao.zhang@intel.com>; dev@dpdk.org
> Cc: Zhang, Xiao <xiao.zhang@intel.com>
> Subject: RE: [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close
> 
> Hi, xiao
> 
> > -----Original Message-----
> > From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Xiao Zhang
> > Sent: Monday, July 8, 2019 7:44 PM
> > To: dev@dpdk.org
> > Cc: Zhang, Xiao <xiao.zhang@intel.com>
> > Subject: [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on
> > reset/close
> >
> > Unit hang may occur if multiple descriptors are available in the rings
> > during reset or close. This state can be detected by configure status by bit 8 in
> register.
> > If the bit is set and there are pending descriptors in one of the
> > rings, we must flush them before reset or close.
> >
> > Signed-off-by: Xiao Zhang <xiao.zhang@intel.com>
> > ---
> >  drivers/net/e1000/base/e1000_ich8lan.h |  1 +
> >  drivers/net/e1000/e1000_ethdev.h       |  1 +
> >  drivers/net/e1000/igb_ethdev.c         |  4 ++
> >  drivers/net/e1000/igb_rxtx.c           | 96
> > ++++++++++++++++++++++++++++++++++
> >  4 files changed, 102 insertions(+)
> >
> > diff --git a/drivers/net/e1000/base/e1000_ich8lan.h
> > b/drivers/net/e1000/base/e1000_ich8lan.h
> > index bc4ed1d..1f2a3f8 100644
> > --- a/drivers/net/e1000/base/e1000_ich8lan.h
> > +++ b/drivers/net/e1000/base/e1000_ich8lan.h
> > @@ -120,6 +120,7 @@ POSSIBILITY OF SUCH DAMAGE.
> >  #define E1000_FEXTNVM7_SIDE_CLK_UNGATE	0x00000004
> >  #if !defined(EXTERNAL_RELEASE) || defined(ULP_SUPPORT)
> >  #define E1000_FEXTNVM7_DISABLE_SMB_PERST	0x00000020
> > +#define E1000_FEXTNVM7_NEED_DESCRING_FLUSH	0x00000100
> >  #endif /* !EXTERNAL_RELEASE || ULP_SUPPORT */
> >  #define E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS	0x00000800
> >  #define E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS	0x00001000
> > diff --git a/drivers/net/e1000/e1000_ethdev.h
> > b/drivers/net/e1000/e1000_ethdev.h
> > index 67acb73..3451979 100644
> > --- a/drivers/net/e1000/e1000_ethdev.h
> > +++ b/drivers/net/e1000/e1000_ethdev.h
> > @@ -522,5 +522,6 @@ int igb_action_rss_same(const struct
> > rte_flow_action_rss *comp,  int igb_config_rss_filter(struct rte_eth_dev *dev,
> >  			struct igb_rte_flow_rss_conf *conf,
> >  			bool add);
> > +void igb_flush_desc_rings(struct rte_eth_dev *dev);
> >
> >  #endif /* _E1000_ETHDEV_H_ */
> > diff --git a/drivers/net/e1000/igb_ethdev.c
> > b/drivers/net/e1000/igb_ethdev.c index 3ee28cf..845101b 100644
> > --- a/drivers/net/e1000/igb_ethdev.c
> > +++ b/drivers/net/e1000/igb_ethdev.c
> > @@ -1589,6 +1589,10 @@ eth_igb_close(struct rte_eth_dev *dev)
> >  	eth_igb_stop(dev);
> >  	adapter->stopped = 1;
> >
> > +	/* Flush desc rings for i219 */
> > +	if (hw->mac.type >= e1000_pch_spt)
> > +		igb_flush_desc_rings(dev);
> > +
> >  	e1000_phy_hw_reset(hw);
> >  	igb_release_manageability(hw);
> >  	igb_hw_control_release(hw);
> > diff --git a/drivers/net/e1000/igb_rxtx.c
> > b/drivers/net/e1000/igb_rxtx.c index c5606de..33eeb4e 100644
> > --- a/drivers/net/e1000/igb_rxtx.c
> > +++ b/drivers/net/e1000/igb_rxtx.c
> > @@ -18,6 +18,7 @@
> >  #include <rte_log.h>
> >  #include <rte_debug.h>
> >  #include <rte_pci.h>
> > +#include <rte_bus_pci.h>
> >  #include <rte_memory.h>
> >  #include <rte_memcpy.h>
> >  #include <rte_memzone.h>
> > @@ -63,6 +64,9 @@
> >  #define IGB_TX_OFFLOAD_NOTSUP_MASK \
> >  		(PKT_TX_OFFLOAD_MASK ^ IGB_TX_OFFLOAD_MASK)
> >
> > +/* PCI offset for querying descriptor ring status*/
> > +#define PCICFG_DESC_RING_STATUS           0xE4
> > +
> >  /**
> >   * Structure associated with each descriptor of the RX ring of a RX queue.
> >   */
> > @@ -2962,3 +2966,95 @@ igb_config_rss_filter(struct rte_eth_dev *dev,
> >
> >  	return 0;
> >  }
> > +
> > +static void e1000_flush_tx_ring(struct rte_eth_dev *dev) {
> > +	struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data-
> > >dev_private);
> > +	volatile union e1000_adv_tx_desc *tx_desc;
> > +	uint32_t tdt, tctl, txd_lower = E1000_TXD_CMD_IFCS;
> > +	uint16_t size = 512;
> > +	struct igb_tx_queue *txq;
> > +
> > +	if (dev->data->tx_queues == NULL)
> > +		return;
> > +	txq = dev->data->tx_queues[0];
> > +
> > +	tctl = E1000_READ_REG(hw, E1000_TCTL);
> > +	E1000_WRITE_REG(hw, E1000_TCTL, tctl | E1000_TCTL_EN);
> > +	tdt = E1000_READ_REG(hw, E1000_TDT(0));
> > +	if (tdt != txq->tx_tail)
> > +		return;
> > +	tx_desc = txq->tx_ring;
> > +	tx_desc->read.buffer_addr = txq->tx_ring_phys_addr;
> > +	tx_desc->read.cmd_type_len = rte_cpu_to_le_32(txd_lower | size);
> > +	tx_desc->read.olinfo_status = 0;
> > +
> > +	rte_wmb();
> > +	txq->tx_tail++;
> > +	if (txq->tx_tail == txq->nb_tx_desc)
> > +		txq->tx_tail = 0;
> > +	rte_io_wmb();
> > +	E1000_WRITE_REG(hw, E1000_TDT(0), txq->tx_tail);
> > +	usec_delay(250);
> > +}
> > +
> > +static void e1000_flush_rx_ring(struct rte_eth_dev *dev) {
> > +	uint32_t rctl, rxdctl;
> > +	struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data-
> > >dev_private);
> > +
> > +	rctl = E1000_READ_REG(hw, E1000_RCTL);
> > +	E1000_WRITE_REG(hw, E1000_TCTL, rctl & ~E1000_RCTL_EN);
> > +	E1000_WRITE_FLUSH(hw);
> > +	usec_delay(150);
> > +
> > +	rxdctl = E1000_READ_REG(hw, E1000_RXDCTL(0));
> > +	/* zero the lower 14 bits (prefetch and host thresholds) */
> > +	rxdctl &= 0xffffc000;
> > +
> > +	/* update thresholds: prefetch threshold to 31, host threshold to 1
> > +	 * and make sure the granularity is "descriptors" and not "cache lines"
> > +	 */
> > +	rxdctl |= (0x1F | (1UL << 8) | E1000_RXDCTL_THRESH_UNIT_DESC);
> > +
> > +	E1000_WRITE_REG(hw, E1000_RXDCTL(0), rxdctl);
> > +	/* momentarily enable the RX ring for the changes to take effect */
> > +	E1000_WRITE_REG(hw, E1000_RCTL, rctl | E1000_RCTL_EN);
> > +	E1000_WRITE_FLUSH(hw);
> > +	usec_delay(150);
> > +	E1000_WRITE_REG(hw, E1000_RCTL, rctl & ~E1000_RCTL_EN); }
> > +
> 
> In dpdk driver, it may enable and use many queues, so why do we only Process tx
> and rx queue 0,  ring for other queues not need to handle?
> 
> 
> 
> 
> 
> 
> > +/**
> > + * igb_flush_desc_rings - remove all descriptors from the descriptor
> > +rings
> > + *
> > + * In i219, the descriptor rings must be emptied before
> > +resetting/closing the
> > + * HW. Failure to do this will cause the HW to enter a unit hang state
> > +which
> > + * can only be released by PCI reset on the device
> > + *
> > + */
> > +
> > +void igb_flush_desc_rings(struct rte_eth_dev *dev) {
> > +	uint32_t fextnvm11, tdlen;
> > +	struct e1000_hw *hw = E1000_DEV_PRIVATE_TO_HW(dev->data-
> > >dev_private);
> > +	struct rte_pci_device *pci_dev = RTE_ETH_DEV_TO_PCI(dev);
> > +	uint32_t hang_state = 0;
> > +
> > +	fextnvm11 = E1000_READ_REG(hw, E1000_FEXTNVM11);
> > +	E1000_WRITE_REG(hw, E1000_FEXTNVM11,
> > +			fextnvm11 | E1000_FEXTNVM11_DISABLE_MULR_FIX);
> > +	tdlen = E1000_READ_REG(hw, E1000_TDLEN(0));
> > +	rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state),
> > +				PCICFG_DESC_RING_STATUS);
> > +
> > +	/* do nothing if we're not in faulty state, or if the queue is empty */
> > +	if ((hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH) &&
> > tdlen) {
> > +		/* flush desc ring */
> > +		e1000_flush_tx_ring(dev);
> > +		rte_pci_read_config(pci_dev, &hang_state, sizeof(hang_state),
> > +					PCICFG_DESC_RING_STATUS);
> > +		if (hang_state & E1000_FEXTNVM7_NEED_DESCRING_FLUSH)
> > +			e1000_flush_rx_ring(dev);
> > +	}
> > +}
> > --
> > 2.7.4


^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2019-07-09  2:46 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-07-08 11:43 [dpdk-dev] [v2] net/e1000: i219 unit hang issue fix on reset/close Xiao Zhang
2019-07-08  8:35 ` Zhao1, Wei
2019-07-09  2:46   ` Zhang, Xiao

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).