From: Julien Meunier <julien.meunier@nokia.com>
To: <konstantin.ananyev@intel.com>, <wenzhuo.lu@intel.com>
Cc: <dev@dpdk.org>
Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for X540/X550
Date: Wed, 2 Jan 2019 18:00:55 +0200 [thread overview]
Message-ID: <20190102160055.30301-1-julien.meunier@nokia.com> (raw)
Loopback mode is also supported on X540 and X550 NICs, according to
their datasheet (section 15.2). The way to set it up is a little
different of the 82599.
Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
---
drivers/net/ixgbe/ixgbe_ethdev.c | 10 ++++++---
drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++---
drivers/net/ixgbe/ixgbe_rxtx.c | 47 ++++++++++++++++++++++++++++++++++------
3 files changed, 49 insertions(+), 13 deletions(-)
diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c b/drivers/net/ixgbe/ixgbe_ethdev.c
index 7493110..7eb3303 100644
--- a/drivers/net/ixgbe/ixgbe_ethdev.c
+++ b/drivers/net/ixgbe/ixgbe_ethdev.c
@@ -2652,9 +2652,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
goto error;
}
- /* Skip link setup if loopback mode is enabled for 82599. */
- if (hw->mac.type == ixgbe_mac_82599EB &&
- dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
+ /* Skip link setup if loopback mode is enabled. */
+ if ((hw->mac.type == ixgbe_mac_82599EB ||
+ hw->mac.type == ixgbe_mac_X540 ||
+ hw->mac.type == ixgbe_mac_X550 ||
+ hw->mac.type == ixgbe_mac_X550EM_x ||
+ hw->mac.type == ixgbe_mac_X550EM_a) &&
+ dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
goto skip_link_setup;
if (ixgbe_is_sfp(hw) && hw->phy.multispeed_fiber) {
diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h
index 565c69c..c60a697 100644
--- a/drivers/net/ixgbe/ixgbe_ethdev.h
+++ b/drivers/net/ixgbe/ixgbe_ethdev.h
@@ -65,9 +65,8 @@
#define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us */
/* Loopback operation modes */
-/* 82599 specific loopback operation types */
-#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is disabled. */
-#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback operation is enabled. */
+#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is disabled. */
+#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is enabled. */
#define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum Jumbo frame size. */
diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c b/drivers/net/ixgbe/ixgbe_rxtx.c
index 9a79d18..0ef7fdf 100644
--- a/drivers/net/ixgbe/ixgbe_rxtx.c
+++ b/drivers/net/ixgbe/ixgbe_rxtx.c
@@ -4879,10 +4879,14 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
/*
- * If loopback mode is configured for 82599, set LPBK bit.
+ * If loopback mode is configured, set LPBK bit.
*/
- if (hw->mac.type == ixgbe_mac_82599EB &&
- dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
+ if ((hw->mac.type == ixgbe_mac_82599EB ||
+ hw->mac.type == ixgbe_mac_X540 ||
+ hw->mac.type == ixgbe_mac_X550 ||
+ hw->mac.type == ixgbe_mac_X550EM_x ||
+ hw->mac.type == ixgbe_mac_X550EM_a) &&
+ dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
hlreg0 |= IXGBE_HLREG0_LPBK;
else
hlreg0 &= ~IXGBE_HLREG0_LPBK;
@@ -5088,6 +5092,29 @@ ixgbe_setup_loopback_link_82599(struct ixgbe_hw *hw)
msec_delay(50);
}
+/*
+ * Set up link loopback for X540 / X550 mode Tx->Rx.
+ */
+static inline void __attribute__((cold))
+ixgbe_setup_loopback_link_x540_x550(struct ixgbe_hw *hw)
+{
+ uint32_t macc;
+ PMD_INIT_FUNC_TRACE();
+
+ /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
+ macc = IXGBE_READ_REG(hw, IXGBE_MACC);
+ macc |= IXGBE_MACC_FLU;
+ IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
+
+ /* Restart link */
+ IXGBE_WRITE_REG(hw,
+ IXGBE_AUTOC,
+ IXGBE_AUTOC_LMS_10G_LINK_NO_AN | IXGBE_AUTOC_FLU);
+
+ hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
+ msec_delay(50);
+}
+
/*
* Start Transmit and Receive Units.
@@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev *dev)
rxctrl |= IXGBE_RXCTRL_RXEN;
hw->mac.ops.enable_rx_dma(hw, rxctrl);
- /* If loopback mode is enabled for 82599, set up the link accordingly */
- if (hw->mac.type == ixgbe_mac_82599EB &&
- dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
- ixgbe_setup_loopback_link_82599(hw);
+ /* If loopback mode is enabled, set up the link accordingly */
+ if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
+ if (hw->mac.type == ixgbe_mac_82599EB)
+ ixgbe_setup_loopback_link_82599(hw);
+ else if (hw->mac.type == ixgbe_mac_X540 ||
+ hw->mac.type == ixgbe_mac_X550 ||
+ hw->mac.type == ixgbe_mac_X550EM_x ||
+ hw->mac.type == ixgbe_mac_X550EM_a)
+ ixgbe_setup_loopback_link_x540_x550(hw);
+ }
#ifdef RTE_LIBRTE_SECURITY
if ((dev->data->dev_conf.rxmode.offloads &
--
2.10.2
next reply other threads:[~2019-01-02 16:01 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-02 16:00 Julien Meunier [this message]
2019-01-07 6:53 ` Zhang, Qi Z
2019-01-07 15:53 ` Meunier, Julien (Nokia - FR/Paris-Saclay)
2019-01-08 10:10 ` Zhao1, Wei
2019-01-08 12:39 ` Zhang, Qi Z
2019-01-08 20:18 ` Meunier, Julien (Nokia - FR/Paris-Saclay)
2019-01-09 1:30 ` Zhao1, Wei
2019-01-07 10:05 ` Zhao1, Wei
2019-01-07 16:04 ` Meunier, Julien (Nokia - FR/Paris-Saclay)
2019-01-08 3:10 ` Zhao1, Wei
2019-02-07 17:30 ` [dpdk-dev] [PATCH 1/2] net/ixgbe: do not start on unsupported loopback mode Julien Meunier
2019-02-07 17:30 ` [dpdk-dev] [PATCH 2/2] net/ixgbe: add support of loopback for X540/X550 Julien Meunier
2019-02-12 6:37 ` Zhao1, Wei
2019-02-18 11:20 ` Meunier, Julien (Nokia - FR/Paris-Saclay)
2019-02-12 6:36 ` [dpdk-dev] [PATCH 1/2] net/ixgbe: do not start on unsupported loopback mode Zhao1, Wei
2019-02-20 21:05 ` [dpdk-dev] [PATCH v3 " Julien Meunier
2019-02-20 21:05 ` [dpdk-dev] [PATCH v3 2/2] net/ixgbe: add support of loopback for X540/X550 Julien Meunier
2019-02-21 2:30 ` Zhao1, Wei
2019-03-01 7:46 ` Zhang, Qi Z
2019-03-01 7:45 ` [dpdk-dev] [PATCH v3 1/2] net/ixgbe: do not start on unsupported loopback mode Zhang, Qi Z
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190102160055.30301-1-julien.meunier@nokia.com \
--to=julien.meunier@nokia.com \
--cc=dev@dpdk.org \
--cc=konstantin.ananyev@intel.com \
--cc=wenzhuo.lu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).