From: Jingjing Wu <jingjing.wu@intel.com>
To: thomas.monjalon@6wind.com
Cc: dev@dpdk.org
Subject: [dpdk-dev] [PATCH v3 2/2] doc: add i40e to overview table
Date: Wed, 9 Mar 2016 15:28:40 +0800 [thread overview]
Message-ID: <1457508520-2751-3-git-send-email-jingjing.wu@intel.com> (raw)
In-Reply-To: <1457508520-2751-1-git-send-email-jingjing.wu@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
---
doc/guides/nics/overview.rst | 82 ++++++++++++++++++++++----------------------
1 file changed, 41 insertions(+), 41 deletions(-)
diff --git a/doc/guides/nics/overview.rst b/doc/guides/nics/overview.rst
index d4c6ff4..431bd1e 100644
--- a/doc/guides/nics/overview.rst
+++ b/doc/guides/nics/overview.rst
@@ -86,61 +86,61 @@ Most of these differences are summarized below.
e e e e e e
c c c c c c
==================== = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
- link status
- link status event
- Rx interrupt
- queue start/stop
+ link status X X
+ link status event X X
+ Rx interrupt X X X X
+ queue start/stop X X X X
MTU update
- jumbo frame
- scattered Rx
+ jumbo frame X X X X
+ scattered Rx X X X X
LRO
- TSO
- promiscuous mode
- allmulticast mode
- unicast MAC filter
- multicast MAC filter
- RSS hash
- RSS key update
- RSS reta update
- VMDq
- SR-IOV
- DCB
- VLAN filter
- ethertype filter
+ TSO X X X X
+ promiscuous mode X X X X
+ allmulticast mode X X X X
+ unicast MAC filter X X X X
+ multicast MAC filter X X X X
+ RSS hash X X X X
+ RSS key update X X X X
+ RSS reta update X X X X
+ VMDq X X
+ SR-IOV X X
+ DCB X X
+ VLAN filter X X X X
+ ethertype filter X X
n-tuple filter
SYN filter
- tunnel filter
+ tunnel filter X X
flexible filter
- hash filter
- flow director
- flow control
+ hash filter X X X X
+ flow director X X
+ flow control X X
rate limitation
- traffic mirroring
- CRC offload
- VLAN offload
- QinQ offload
- L3 checksum offload
- L4 checksum offload
- inner L3 checksum
- inner L4 checksum
- packet type parsing
- timesync
- basic stats
- extended stats
+ traffic mirroring X X
+ CRC offload X X
+ VLAN offload X X
+ QinQ offload X X
+ L3 checksum offload X X
+ L4 checksum offload X X
+ inner L3 checksum X X
+ inner L4 checksum X X
+ packet type parsing X X
+ timesync X X
+ basic stats X X X X
+ extended stats X X X X
stats per queue
EEPROM dump
registers dump
- multiprocess aware
- BSD nic_uio
- Linux UIO
- Linux VFIO
+ multiprocess aware X X X X
+ BSD nic_uio X X X X
+ Linux UIO X X X X
+ Linux VFIO X X X X
other kdrv
ARMv7
ARMv8
Power8
TILE-Gx
- x86-32
- x86-64
+ x86-32 X X X X
+ x86-64 X X X X
usage doc
design doc
perf doc
--
2.4.0
next prev parent reply other threads:[~2016-03-09 7:28 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-01-28 8:50 [dpdk-dev] [PATCH] doc: add doc for i40e pmd driver introduction Jingjing Wu
2016-02-22 5:49 ` Lu, Wenzhuo
2016-02-22 15:34 ` Mcnamara, John
2016-02-23 1:23 ` [dpdk-dev] [PATCH v2] " Jingjing Wu
2016-02-23 10:21 ` Mcnamara, John
2016-03-06 22:39 ` Thomas Monjalon
2016-03-07 2:37 ` Wu, Jingjing
2016-03-07 8:35 ` Thomas Monjalon
2016-03-07 8:38 ` Wu, Jingjing
2016-03-09 7:28 ` [dpdk-dev] [PATCH v3 0/2] doc: add " Jingjing Wu
2016-03-09 7:28 ` [dpdk-dev] [PATCH v3 1/2] doc: add doc for " Jingjing Wu
2016-03-09 7:28 ` Jingjing Wu [this message]
2016-03-09 17:01 ` [dpdk-dev] [PATCH v3 0/2] doc: add " Thomas Monjalon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1457508520-2751-3-git-send-email-jingjing.wu@intel.com \
--to=jingjing.wu@intel.com \
--cc=dev@dpdk.org \
--cc=thomas.monjalon@6wind.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).