* [dpdk-dev] No RX frames on Intel 82599 VF
@ 2016-07-11 18:22 Garik E
2016-07-12 1:24 ` Lu, Wenzhuo
0 siblings, 1 reply; 6+ messages in thread
From: Garik E @ 2016-07-11 18:22 UTC (permalink / raw)
To: dev
Hello,
I have two Intel servers S2600WTTR and S2600WT2 both with 82599 10G
Ethernet Controllers
I run the same DPDK application on both servers.
The application works with one interface bound to physical or virtual PCI
function depending on configuration
The S2600WTTR server receives incoming traffic on physical and virtual
functions
The S2600WT2 server receives traffic only on physical function
When I bind S2600WT2 VF to ixgbevf driver and configure it as Linux ETH
interface, it works normally.
Network sniffer shows that Ethernet frames arrive to S2600WT2 port and
frames are valid,
however DPDK does not receive them.
Where can I start to debug this issue ?
OS: RHEL 6.6 x86-64
DPDK: 16-07-rc1
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [dpdk-dev] No RX frames on Intel 82599 VF
2016-07-11 18:22 [dpdk-dev] No RX frames on Intel 82599 VF Garik E
@ 2016-07-12 1:24 ` Lu, Wenzhuo
2016-07-12 4:48 ` Garik E
0 siblings, 1 reply; 6+ messages in thread
From: Lu, Wenzhuo @ 2016-07-12 1:24 UTC (permalink / raw)
To: Garik E, dev
Hi Garik,
> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Garik E
> Sent: Tuesday, July 12, 2016 2:22 AM
> To: dev@dpdk.org
> Subject: [dpdk-dev] No RX frames on Intel 82599 VF
>
> Hello,
>
>
> I have two Intel servers S2600WTTR and S2600WT2 both with 82599 10G
> Ethernet Controllers
>
> I run the same DPDK application on both servers.
>
> The application works with one interface bound to physical or virtual PCI
> function depending on configuration
>
> The S2600WTTR server receives incoming traffic on physical and virtual
> functions
S2600WTTR is working right?
>
> The S2600WT2 server receives traffic only on physical function
>
> When I bind S2600WT2 VF to ixgbevf driver and configure it as Linux ETH
> interface, it works normally.
Don't understand what you're doing here. And you say *works*? Is S2600WT2 the one not working?
>
>
> Network sniffer shows that Ethernet frames arrive to S2600WT2 port and
> frames are valid,
>
> however DPDK does not receive them.
>
>
> Where can I start to debug this issue ?
>
>
> OS: RHEL 6.6 x86-64
>
> DPDK: 16-07-rc1
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [dpdk-dev] No RX frames on Intel 82599 VF
2016-07-12 1:24 ` Lu, Wenzhuo
@ 2016-07-12 4:48 ` Garik E
2016-07-12 6:04 ` Garik E
2016-07-12 6:43 ` Lu, Wenzhuo
0 siblings, 2 replies; 6+ messages in thread
From: Garik E @ 2016-07-12 4:48 UTC (permalink / raw)
To: Lu, Wenzhuo; +Cc: dev
Hi,
On the S2600WT2 server, when DPDK is bound to VF, there is no incoming
traffic.
But when the same VF is bound to ixgbevf driver and configured as Linux
interface,
it works normally. I was able to run ping and ssh through that VF.
So my guess is that the RX issue is not due to malfunction hardware.
The same binary works correctly on S2600WTTR server with 82599 VF
I also tested the application with Mellanox ConnectX-4 on both servers
There were no issues with CX-4 PF and VF
For some reason DPDK VF RX functionality does not work on S2600WT2.
On Tue, Jul 12, 2016 at 4:24 AM, Lu, Wenzhuo <wenzhuo.lu@intel.com> wrote:
> Hi Garik,
>
> > -----Original Message-----
> > From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Garik E
> > Sent: Tuesday, July 12, 2016 2:22 AM
> > To: dev@dpdk.org
> > Subject: [dpdk-dev] No RX frames on Intel 82599 VF
> >
> > Hello,
> >
> >
> > I have two Intel servers S2600WTTR and S2600WT2 both with 82599 10G
> > Ethernet Controllers
> >
> > I run the same DPDK application on both servers.
> >
> > The application works with one interface bound to physical or virtual PCI
> > function depending on configuration
> >
> > The S2600WTTR server receives incoming traffic on physical and virtual
> > functions
> S2600WTTR is working right?
>
> >
> > The S2600WT2 server receives traffic only on physical function
> >
> > When I bind S2600WT2 VF to ixgbevf driver and configure it as Linux ETH
> > interface, it works normally.
> Don't understand what you're doing here. And you say *works*? Is S2600WT2
> the one not working?
>
> >
> >
> > Network sniffer shows that Ethernet frames arrive to S2600WT2 port and
> > frames are valid,
> >
> > however DPDK does not receive them.
> >
> >
> > Where can I start to debug this issue ?
> >
> >
> > OS: RHEL 6.6 x86-64
> >
> > DPDK: 16-07-rc1
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [dpdk-dev] No RX frames on Intel 82599 VF
2016-07-12 4:48 ` Garik E
@ 2016-07-12 6:04 ` Garik E
2016-07-12 6:43 ` Lu, Wenzhuo
1 sibling, 0 replies; 6+ messages in thread
From: Garik E @ 2016-07-12 6:04 UTC (permalink / raw)
To: Lu, Wenzhuo; +Cc: dev
On Tue, Jul 12, 2016 at 7:48 AM, Garik E <kiragon@gmail.com> wrote:
> Hi,
>
> On the S2600WT2 server, when DPDK is bound to VF, there is no incoming
> traffic.
> But when the same VF is bound to ixgbevf driver and configured as Linux
> interface,
> it works normally. I was able to run ping and ssh through that VF.
> So my guess is that the RX issue is not due to malfunction hardware.
>
> The same binary works correctly on S2600WTTR server with 82599 VF
> I also tested the application with Mellanox ConnectX-4 on both servers
> There were no issues with CX-4 PF and VF
>
> For some reason DPDK 82599 VF RX functionality does not work on S2600WT2.
>
>
>
>
>
> On Tue, Jul 12, 2016 at 4:24 AM, Lu, Wenzhuo <wenzhuo.lu@intel.com> wrote:
>
>> Hi Garik,
>>
>> > -----Original Message-----
>> > From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Garik E
>> > Sent: Tuesday, July 12, 2016 2:22 AM
>> > To: dev@dpdk.org
>> > Subject: [dpdk-dev] No RX frames on Intel 82599 VF
>> >
>> > Hello,
>> >
>> >
>> > I have two Intel servers S2600WTTR and S2600WT2 both with 82599 10G
>> > Ethernet Controllers
>> >
>> > I run the same DPDK application on both servers.
>> >
>> > The application works with one interface bound to physical or virtual
>> PCI
>> > function depending on configuration
>> >
>> > The S2600WTTR server receives incoming traffic on physical and virtual
>> > functions
>> S2600WTTR is working right?
>>
>> >
>> > The S2600WT2 server receives traffic only on physical function
>> >
>> > When I bind S2600WT2 VF to ixgbevf driver and configure it as Linux ETH
>> > interface, it works normally.
>> Don't understand what you're doing here. And you say *works*? Is S2600WT2
>> the one not working?
>>
>> >
>> >
>> > Network sniffer shows that Ethernet frames arrive to S2600WT2 port and
>> > frames are valid,
>> >
>> > however DPDK does not receive them.
>> >
>> >
>> > Where can I start to debug this issue ?
>> >
>> >
>> > OS: RHEL 6.6 x86-64
>> >
>> > DPDK: 16-07-rc1
>>
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [dpdk-dev] No RX frames on Intel 82599 VF
2016-07-12 4:48 ` Garik E
2016-07-12 6:04 ` Garik E
@ 2016-07-12 6:43 ` Lu, Wenzhuo
2017-04-19 9:49 ` Bill Bonaparte
1 sibling, 1 reply; 6+ messages in thread
From: Lu, Wenzhuo @ 2016-07-12 6:43 UTC (permalink / raw)
To: Garik E; +Cc: dev
From: Garik E [mailto:kiragon@gmail.com]
Sent: Tuesday, July 12, 2016 12:48 PM
To: Lu, Wenzhuo
Cc: dev@dpdk.org
Subject: Re: [dpdk-dev] No RX frames on Intel 82599 VF
Hi,
On the S2600WT2 server, when DPDK is bound to VF, there is no incoming traffic.
But when the same VF is bound to ixgbevf driver and configured as Linux interface,
it works normally. I was able to run ping and ssh through that VF.
So my guess is that the RX issue is not due to malfunction hardware.
The same binary works correctly on S2600WTTR server with 82599 VF
I also tested the application with Mellanox ConnectX-4 on both servers
There were no issues with CX-4 PF and VF
For some reason DPDK VF RX functionality does not work on S2600WT2.
[Wenzhuo] No clue now. But I think you can compare what’s the difference between S2600WT2 and S2600WTTR.
On Tue, Jul 12, 2016 at 4:24 AM, Lu, Wenzhuo <wenzhuo.lu@intel.com<mailto:wenzhuo.lu@intel.com>> wrote:
Hi Garik,
> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org<mailto:dev-bounces@dpdk.org>] On Behalf Of Garik E
> Sent: Tuesday, July 12, 2016 2:22 AM
> To: dev@dpdk.org<mailto:dev@dpdk.org>
> Subject: [dpdk-dev] No RX frames on Intel 82599 VF
>
> Hello,
>
>
> I have two Intel servers S2600WTTR and S2600WT2 both with 82599 10G
> Ethernet Controllers
>
> I run the same DPDK application on both servers.
>
> The application works with one interface bound to physical or virtual PCI
> function depending on configuration
>
> The S2600WTTR server receives incoming traffic on physical and virtual
> functions
S2600WTTR is working right?
>
> The S2600WT2 server receives traffic only on physical function
>
> When I bind S2600WT2 VF to ixgbevf driver and configure it as Linux ETH
> interface, it works normally.
Don't understand what you're doing here. And you say *works*? Is S2600WT2 the one not working?
>
>
> Network sniffer shows that Ethernet frames arrive to S2600WT2 port and
> frames are valid,
>
> however DPDK does not receive them.
>
>
> Where can I start to debug this issue ?
>
>
> OS: RHEL 6.6 x86-64
>
> DPDK: 16-07-rc1
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [dpdk-dev] No RX frames on Intel 82599 VF
2016-07-12 6:43 ` Lu, Wenzhuo
@ 2017-04-19 9:49 ` Bill Bonaparte
0 siblings, 0 replies; 6+ messages in thread
From: Bill Bonaparte @ 2017-04-19 9:49 UTC (permalink / raw)
To: Lu, Wenzhuo; +Cc: Garik E, dev
I have the same problem on my 82599 nic, after I turnoff the jumbo_frame,
it works.
you can try rte_eth_dev_configure with the dev_conf.jumbo_frame = 0.
On Tue, Jul 12, 2016 at 2:43 PM, Lu, Wenzhuo <wenzhuo.lu@intel.com> wrote:
> From: Garik E [mailto:kiragon@gmail.com]
> Sent: Tuesday, July 12, 2016 12:48 PM
> To: Lu, Wenzhuo
> Cc: dev@dpdk.org
> Subject: Re: [dpdk-dev] No RX frames on Intel 82599 VF
>
> Hi,
>
> On the S2600WT2 server, when DPDK is bound to VF, there is no incoming
> traffic.
> But when the same VF is bound to ixgbevf driver and configured as Linux
> interface,
> it works normally. I was able to run ping and ssh through that VF.
> So my guess is that the RX issue is not due to malfunction hardware.
>
> The same binary works correctly on S2600WTTR server with 82599 VF
> I also tested the application with Mellanox ConnectX-4 on both servers
> There were no issues with CX-4 PF and VF
>
> For some reason DPDK VF RX functionality does not work on S2600WT2.
> [Wenzhuo] No clue now. But I think you can compare what’s the difference
> between S2600WT2 and S2600WTTR.
>
>
>
> On Tue, Jul 12, 2016 at 4:24 AM, Lu, Wenzhuo <wenzhuo.lu@intel.com<mailto:
> wenzhuo.lu@intel.com>> wrote:
> Hi Garik,
>
> > -----Original Message-----
> > From: dev [mailto:dev-bounces@dpdk.org<mailto:dev-bounces@dpdk.org>] On
> Behalf Of Garik E
> > Sent: Tuesday, July 12, 2016 2:22 AM
> > To: dev@dpdk.org<mailto:dev@dpdk.org>
> > Subject: [dpdk-dev] No RX frames on Intel 82599 VF
> >
> > Hello,
> >
> >
> > I have two Intel servers S2600WTTR and S2600WT2 both with 82599 10G
> > Ethernet Controllers
> >
> > I run the same DPDK application on both servers.
> >
> > The application works with one interface bound to physical or virtual PCI
> > function depending on configuration
> >
> > The S2600WTTR server receives incoming traffic on physical and virtual
> > functions
> S2600WTTR is working right?
>
> >
> > The S2600WT2 server receives traffic only on physical function
> >
> > When I bind S2600WT2 VF to ixgbevf driver and configure it as Linux ETH
> > interface, it works normally.
> Don't understand what you're doing here. And you say *works*? Is S2600WT2
> the one not working?
>
> >
> >
> > Network sniffer shows that Ethernet frames arrive to S2600WT2 port and
> > frames are valid,
> >
> > however DPDK does not receive them.
> >
> >
> > Where can I start to debug this issue ?
> >
> >
> > OS: RHEL 6.6 x86-64
> >
> > DPDK: 16-07-rc1
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2017-04-19 9:50 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-07-11 18:22 [dpdk-dev] No RX frames on Intel 82599 VF Garik E
2016-07-12 1:24 ` Lu, Wenzhuo
2016-07-12 4:48 ` Garik E
2016-07-12 6:04 ` Garik E
2016-07-12 6:43 ` Lu, Wenzhuo
2017-04-19 9:49 ` Bill Bonaparte
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).