[dpdk-dev] [PATCH 1/3] compress/isal: enable checksum support in driver

[dpdk-dev] [PATCH 1/3] compress/isal: enable checksum support in driver

[Lee Daly]

This patch adds checksum support in the ISA-L  PMD for both compression
and decompression.
CRC32 is supported as well as Adler32.

Signed-off-by: Lee Daly <lee.daly@intel.com>
---
 drivers/compress/isal/isal_compress_pmd.c     | 82 +++++++++++++++++++++++----
 drivers/compress/isal/isal_compress_pmd_ops.c |  4 +-
 2 files changed, 73 insertions(+), 13 deletions(-)

diff --git a/drivers/compress/isal/isal_compress_pmd.c b/drivers/compress/isal/isal_compress_pmd.c
index e943336..e377417 100644
--- a/drivers/compress/isal/isal_compress_pmd.c
+++ b/drivers/compress/isal/isal_compress_pmd.c
@@ -16,8 +16,11 @@
 #define RTE_COMP_ISAL_LEVEL_ONE 1
 #define RTE_COMP_ISAL_LEVEL_TWO 2
 #define RTE_COMP_ISAL_LEVEL_THREE 3 /* Optimised for AVX512 & AVX2 only */
+#define RTE_COMP_ISAL_CRC_SIZE 8
+#define RTE_COMP_ISAL_ADLER_SIZE 4
 
 int isal_logtype_driver;
+uint8_t checksum_size;
 
 /* Verify and set private xform parameters */
 int
@@ -43,12 +46,6 @@ isal_comp_set_priv_xform_parameters(struct isal_priv_xform *priv_xform,
 		}
 		priv_xform->compress.algo = RTE_COMP_ALGO_DEFLATE;
 
-		/* Set private xform checksum - raw deflate by default */
-		if (xform->compress.chksum != RTE_COMP_CHECKSUM_NONE) {
-			ISAL_PMD_LOG(ERR, "Checksum not supported\n");
-			return -ENOTSUP;
-		}
-
 		/* Set private xform window size, 32K supported */
 		if (xform->compress.window_size == RTE_COMP_ISAL_WINDOW_SIZE)
 			priv_xform->compress.window_size =
@@ -77,6 +74,29 @@ isal_comp_set_priv_xform_parameters(struct isal_priv_xform *priv_xform,
 			return -ENOTSUP;
 		}
 
+		/* Set private xform checksum */
+		switch (xform->compress.chksum) {
+		/* Raw deflate by default */
+		case(RTE_COMP_CHECKSUM_NONE):
+			priv_xform->compress.chksum = IGZIP_DEFLATE;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32):
+			priv_xform->compress.chksum = IGZIP_GZIP_NO_HDR;
+			checksum_size = RTE_COMP_ISAL_CRC_SIZE;
+			break;
+		case(RTE_COMP_CHECKSUM_ADLER32):
+			priv_xform->compress.chksum = IGZIP_ZLIB_NO_HDR;
+			checksum_size = RTE_COMP_ISAL_ADLER_SIZE;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32_ADLER32):
+			ISAL_PMD_LOG(ERR, "Combined CRC and ADLER checksum not"
+					" supported\n");
+			return -ENOTSUP;
+		default:
+			ISAL_PMD_LOG(ERR, "Checksum type not supported\n");
+			return -ENOTSUP;
+		}
+
 		/* Set private xform level.
 		 * Checking compliance with compressdev API, -1 <= level => 9
 		 */
@@ -170,9 +190,26 @@ isal_comp_set_priv_xform_parameters(struct isal_priv_xform *priv_xform,
 		}
 		priv_xform->decompress.algo = RTE_COMP_ALGO_DEFLATE;
 
-		/* Set private xform checksum - raw deflate by default */
-		if (xform->compress.chksum != RTE_COMP_CHECKSUM_NONE) {
-			ISAL_PMD_LOG(ERR, "Checksum not supported\n");
+		/* Set private xform checksum */
+		switch (xform->decompress.chksum) {
+		/* Raw deflate by default */
+		case(RTE_COMP_CHECKSUM_NONE):
+			priv_xform->decompress.chksum = ISAL_DEFLATE;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32):
+			priv_xform->decompress.chksum = ISAL_GZIP_NO_HDR;
+			checksum_size = RTE_COMP_ISAL_CRC_SIZE;
+			break;
+		case(RTE_COMP_CHECKSUM_ADLER32):
+			priv_xform->decompress.chksum = ISAL_ZLIB_NO_HDR;
+			checksum_size = RTE_COMP_ISAL_ADLER_SIZE;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32_ADLER32):
+			ISAL_PMD_LOG(ERR, "Combined CRC and ADLER checksum not"
+					" supported\n");
+			return -ENOTSUP;
+		default:
+			ISAL_PMD_LOG(ERR, "Checksum type not supported\n");
 			return -ENOTSUP;
 		}
 
@@ -377,6 +414,9 @@ process_isal_deflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
 
 	qp->stream->level_buf = temp_level_buf;
 
+	/* Set Checksum flag */
+	qp->stream->gzip_flag = priv_xform->compress.chksum;
+
 	/* Stateless operation, input will be consumed in one go */
 	qp->stream->flush = NO_FLUSH;
 
@@ -461,14 +501,25 @@ process_isal_deflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
 		}
 	}
 		op->consumed = qp->stream->total_in;
-		op->produced = qp->stream->total_out;
+		/* If checksum requested, total_out must be adjusted
+		 * to reflect only compressed data.
+		 */
+		op->produced = qp->stream->gzip_flag == IGZIP_DEFLATE ?
+				qp->stream->total_out :
+				qp->stream->total_out - checksum_size;
+
+		op->output_chksum = (qp->stream->gzip_flag == IGZIP_ZLIB_NO_HDR)
+				? qp->stream->internal_state.crc + 1
+				: qp->stream->internal_state.crc;
+		isal_deflate_reset(qp->stream);
 
 	return ret;
 }
 
 /* Stateless Decompression Function */
 static int
-process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp)
+process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
+		struct isal_priv_xform *priv_xform)
 {
 	int ret = 0;
 
@@ -477,6 +528,9 @@ process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp)
 	/* Initialize decompression state */
 	isal_inflate_init(qp->state);
 
+	/* Set Checksum flag */
+	qp->state->crc_flag = priv_xform->decompress.chksum;
+
 	if (op->m_src->pkt_len < (op->src.length + op->src.offset)) {
 		ISAL_PMD_LOG(ERR, "Input mbuf(s) not big enough.\n");
 		op->status = RTE_COMP_OP_STATUS_INVALID_ARGS;
@@ -538,6 +592,10 @@ process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp)
 		op->consumed = op->src.length - qp->state->avail_in;
 	}
 		op->produced = qp->state->total_out;
+		op->output_chksum = qp->state->crc;
+
+		isal_inflate_reset(qp->state);
+
 
 	return ret;
 }
@@ -552,7 +610,7 @@ process_op(struct isal_comp_qp *qp, struct rte_comp_op *op,
 		process_isal_deflate(op, qp, priv_xform);
 		break;
 	case RTE_COMP_DECOMPRESS:
-		process_isal_inflate(op, qp);
+		process_isal_inflate(op, qp, priv_xform);
 		break;
 	default:
 		ISAL_PMD_LOG(ERR, "Operation Not Supported\n");
diff --git a/drivers/compress/isal/isal_compress_pmd_ops.c b/drivers/compress/isal/isal_compress_pmd_ops.c
index 41cade8..7b91849 100644
--- a/drivers/compress/isal/isal_compress_pmd_ops.c
+++ b/drivers/compress/isal/isal_compress_pmd_ops.c
@@ -17,7 +17,9 @@ static const struct rte_compressdev_capabilities isal_pmd_capabilities[] = {
 					RTE_COMP_FF_OOP_LB_IN_SGL_OUT |
 					RTE_COMP_FF_SHAREABLE_PRIV_XFORM |
 					RTE_COMP_FF_HUFFMAN_FIXED |
-					RTE_COMP_FF_HUFFMAN_DYNAMIC,
+					RTE_COMP_FF_HUFFMAN_DYNAMIC |
+					RTE_COMP_FF_CRC32_CHECKSUM |
+					RTE_COMP_FF_ADLER32_CHECKSUM,
 		.window_size = {
 			.min = 15,
 			.max = 15,
-- 
2.7.4

[dpdk-dev] [PATCH 2/3] test/compress: add checksum tests

[Lee Daly]

This patch adds a test which examines what type of checksum the PMD
supports, adler, crc32 or alder32_crc32
and tests that feature if the PMD supports it.

Signed-off-by: Lee Daly <lee.daly@intel.com>
---
 test/test/test_compressdev.c | 205 ++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 202 insertions(+), 3 deletions(-)

diff --git a/test/test/test_compressdev.c b/test/test/test_compressdev.c
index 8645388..7ee670f 100644
--- a/test/test/test_compressdev.c
+++ b/test/test/test_compressdev.c
@@ -312,11 +312,16 @@ compress_zlib(struct rte_comp_op *op,
 	else
 		strategy = Z_DEFAULT_STRATEGY;
 
+
 	/*
 	 * Window bits is the base two logarithm of the window size (in bytes).
 	 * When doing raw DEFLATE, this number will be negative.
 	 */
 	window_bits = -(xform->compress.window_size);
+	if (xform->compress.chksum == RTE_COMP_CHECKSUM_ADLER32)
+		window_bits *= -1;
+	else if (xform->compress.chksum == RTE_COMP_CHECKSUM_CRC32)
+		window_bits += 46;
 
 	comp_level = xform->compress.level;
 
@@ -369,6 +374,11 @@ compress_zlib(struct rte_comp_op *op,
 	zlib_flush = map_zlib_flush_flag(op->flush_flag);
 	ret = deflate(&stream, zlib_flush);
 
+	if (xform->compress.chksum == RTE_COMP_CHECKSUM_ADLER32)
+		op->m_dst->buf_addr += 2;
+	else if (xform->compress.chksum == RTE_COMP_CHECKSUM_CRC32)
+		op->m_dst->buf_addr += 10;
+
 	if (stream.avail_in != 0) {
 		RTE_LOG(ERR, USER1, "Buffer could not be read entirely\n");
 		goto exit;
@@ -400,8 +410,14 @@ compress_zlib(struct rte_comp_op *op,
 	}
 
 	op->consumed = stream.total_in;
-	op->produced = stream.total_out;
+	if (xform->compress.chksum == RTE_COMP_CHECKSUM_ADLER32)
+		op->produced = stream.total_out - 6;
+	else if (xform->compress.chksum == RTE_COMP_CHECKSUM_CRC32)
+		op->produced = stream.total_out - 18;
+	else
+		op->produced = stream.total_out;
 	op->status = RTE_COMP_OP_STATUS_SUCCESS;
+	op->output_chksum = stream.adler;
 
 	deflateReset(&stream);
 
@@ -435,7 +451,6 @@ decompress_zlib(struct rte_comp_op *op,
 	 * When doing raw DEFLATE, this number will be negative.
 	 */
 	window_bits = -(xform->decompress.window_size);
-
 	ret = inflateInit2(&stream, window_bits);
 
 	if (ret != Z_OK) {
@@ -651,6 +666,7 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 	const struct rte_compressdev_capabilities *capa =
 		rte_compressdev_capability_get(0, RTE_COMP_ALGO_DEFLATE);
 	char *contig_buf = NULL;
+	uint64_t compress_checksum[num_bufs];
 
 	/* Initialize all arrays to NULL */
 	memset(uncomp_bufs, 0, sizeof(struct rte_mbuf *) * num_bufs);
@@ -837,6 +853,7 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 					&ops_processed[num_total_deqd], num_bufs);
 			num_total_deqd += num_deqd;
 			deqd_retries++;
+
 		} while (num_total_deqd < num_enqd);
 
 		deqd_retries = 0;
@@ -865,6 +882,8 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 		RTE_LOG(DEBUG, USER1, "Compression ratio = %.2f",
 			(float)ops_processed[i]->produced /
 			ops_processed[i]->consumed * 100);
+		if (compress_xform->chksum != RTE_COMP_CHECKSUM_NONE)
+			compress_checksum[i] = ops_processed[i]->output_chksum;
 		ops[i] = NULL;
 	}
 
@@ -1094,9 +1113,18 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 			goto exit;
 		}
 
+		/* Test checksums */
+		if (compress_xforms[0]->compress.chksum !=
+				RTE_COMP_CHECKSUM_NONE) {
+			if (ops_processed[i]->output_chksum !=
+					compress_checksum[i]) {
+				RTE_LOG(ERR, USER1, "The checksums differ\n");
+				goto exit;
+			}
+		}
+
 		buf2 = rte_pktmbuf_read(ops_processed[i]->m_dst, 0,
 				ops_processed[i]->produced, contig_buf);
-
 		if (compare_buffers(buf1, strlen(buf1) + 1,
 				buf2, ops_processed[i]->produced) < 0)
 			goto exit;
@@ -1452,6 +1480,175 @@ test_compressdev_deflate_stateless_sgl(void)
 	}
 
 	return TEST_SUCCESS;
+
+}
+
+static int
+test_compressdev_deflate_stateless_checksum(void)
+{
+	struct comp_testsuite_params *ts_params = &testsuite_params;
+	const char *test_buffer;
+	uint16_t i;
+	int ret;
+	const struct rte_compressdev_capabilities *capab;
+
+	capab = rte_compressdev_capability_get(0, RTE_COMP_ALGO_DEFLATE);
+	TEST_ASSERT(capab != NULL, "Failed to retrieve device capabilities");
+
+	/* Check if driver supports any checksum */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_CRC32_CHECKSUM) == 0 &&
+		(capab->comp_feature_flags & RTE_COMP_FF_ADLER32_CHECKSUM) == 0 &&
+		(capab->comp_feature_flags & RTE_COMP_FF_CRC32_ADLER32_CHECKSUM) == 0)
+		return -ENOTSUP;
+
+	struct rte_comp_xform *compress_xform =
+			rte_malloc(NULL, sizeof(struct rte_comp_xform), 0);
+	if (compress_xform == NULL) {
+		RTE_LOG(ERR, USER1, "Compress xform could not be created\n");
+		ret = TEST_FAILED;
+		goto exit;
+	}
+
+	memcpy(compress_xform, ts_params->def_comp_xform,
+			sizeof(struct rte_comp_xform));
+
+	struct rte_comp_xform *decompress_xform =
+			rte_malloc(NULL, sizeof(struct rte_comp_xform), 0);
+	if (decompress_xform == NULL) {
+		RTE_LOG(ERR, USER1, "Decompress xform could not be created\n");
+		ret = TEST_FAILED;
+		goto exit;
+	}
+
+	memcpy(decompress_xform, ts_params->def_decomp_xform,
+			sizeof(struct rte_comp_xform));
+
+	/* Check if driver supports crc32 checksum and test */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_CRC32_CHECKSUM)) {
+		compress_xform->compress.chksum = RTE_COMP_CHECKSUM_CRC32;
+		decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_CRC32;
+
+		for (i = 0; i < RTE_DIM(compress_test_bufs); i++) {
+			test_buffer = compress_test_bufs[i];
+
+			/* Generate zlib checksum and test against selected
+			 * drivers decompression checksum
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_COMPRESS) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+
+			/* Generate compression and decompression
+			 * checksum of selected driver
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_NONE) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+		}
+	}
+
+	/* Check if driver supports adler32 checksum and test */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_ADLER32_CHECKSUM)) {
+		compress_xform->compress.chksum = RTE_COMP_CHECKSUM_ADLER32;
+		decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_ADLER32;
+
+		for (i = 0; i < RTE_DIM(compress_test_bufs); i++) {
+			test_buffer = compress_test_bufs[i];
+
+			/* Generate zlib checksum and test against selected
+			 * drivers decompression checksum
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_COMPRESS) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+			/* Generate compression and decompression
+			 * checksum of selected driver
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_NONE) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+		}
+	}
+
+	/* Check if driver supports combined crc and adler checksum and test */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_CRC32_ADLER32_CHECKSUM)) {
+		compress_xform->compress.chksum =
+				RTE_COMP_CHECKSUM_CRC32_ADLER32;
+		decompress_xform->decompress.chksum =
+				RTE_COMP_CHECKSUM_CRC32_ADLER32;
+
+		for (i = 0; i < RTE_DIM(compress_test_bufs); i++) {
+			test_buffer = compress_test_bufs[i];
+
+			/* Generate zlib checksum and test against selected
+			 * drivers decompression checksum
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_COMPRESS) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+			/* Generate compression and decompression
+			 * checksum of selected driver
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_NONE) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+		}
+	}
+
+	ret = TEST_SUCCESS;
+
+exit:
+	rte_free(compress_xform);
+	rte_free(decompress_xform);
+	return ret;
 }
 
 static struct unit_test_suite compressdev_testsuite  = {
@@ -1473,6 +1670,8 @@ static struct unit_test_suite compressdev_testsuite  = {
 			test_compressdev_deflate_stateless_multi_xform),
 		TEST_CASE_ST(generic_ut_setup, generic_ut_teardown,
 			test_compressdev_deflate_stateless_sgl),
+		TEST_CASE_ST(generic_ut_setup, generic_ut_teardown,
+			test_compressdev_deflate_stateless_checksum),
 		TEST_CASES_END() /**< NULL terminate unit test array */
 	}
 };
-- 
2.7.4

[dpdk-dev] [PATCH 3/3] doc: update ISA-L guide to reflect checksum support

[Lee Daly]

This updates the ISA-L compression driver guide on how to enable and use
checksums.

This also updates the compression drivers features matrix.

Signed-off-by: Lee Daly <lee.daly@intel.com>
---
 doc/guides/compressdevs/features/isal.ini |  2 ++
 doc/guides/compressdevs/isal.rst          | 32 +++++++++++++++++++++++++++++--
 2 files changed, 32 insertions(+), 2 deletions(-)

diff --git a/doc/guides/compressdevs/features/isal.ini b/doc/guides/compressdevs/features/isal.ini
index 919cf70..e705031 100644
--- a/doc/guides/compressdevs/features/isal.ini
+++ b/doc/guides/compressdevs/features/isal.ini
@@ -12,5 +12,7 @@ OOP SGL In SGL Out = Y
 OOP SGL In LB  Out = Y
 OOP LB  In SGL Out = Y
 Deflate            = Y
+Adler32            = Y
+Crc32              = Y
 Fixed              = Y
 Dynamic            = Y
diff --git a/doc/guides/compressdevs/isal.rst b/doc/guides/compressdevs/isal.rst
index 3bc3022..f7d3d01 100644
--- a/doc/guides/compressdevs/isal.rst
+++ b/doc/guides/compressdevs/isal.rst
@@ -27,6 +27,35 @@ Window size support:
 
     * 32K
 
+Checksum:
+
+    * CRC32
+    * ADLER32
+
+To enable a checksum in the driver, the compression and/or decompression xform
+structure, rte_comp_xform, must be filled with either of the CompressDevs
+checksum flags supported. ::
+
+ compress_xform->compress.chksum = RTE_COMP_CHECKSUM_CRC32
+
+ decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_CRC32
+
+::
+
+ compress_xform->compress.chksum = RTE_COMP_CHECKSUM_ADLER32
+
+ decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_ADLER32
+
+If you request a checksum for compression, the checksum field in the operation
+structure, ``op->input_chksum``, will be filled with the checksum of the input data.
+
+If you request a checksum for decompression, the checksum field in the operation
+structure, ``op->output_chksum``, will be filled with the checksum of the output data.
+
+.. Note::
+
+ For the compression case above, your output buffer will need to be large enough to hold the compressed data plus a scratchpad for the checksum at the end, the scratchpad is 8 bytes for CRC32 and 4 bytes for Adler32.
+
 Level guide:
 
 The ISA-L levels have been mapped to somewhat correspond to the same ZLIB level,
@@ -75,13 +104,12 @@ As a result the level mappings from the API to the PMD are shown below.
  The above table only shows mapping when API calls for dynamic compression.
  For fixed compression, regardless of API level, internally ISA-L level 0 is always used.
 
+
 Limitations
 -----------
 
 * Compressdev level 0, no compression, is not supported.
 
-* Checksums will not be supported until future release.
-
 Installation
 ------------
 
-- 
2.7.4

Re: [dpdk-dev] [PATCH 3/3] doc: update ISA-L guide to reflect checksum support

[Trahe, Fiona]

Hi Lee,

> +If you request a checksum for compression, the checksum field in the operation
> +structure, ``op->input_chksum``, will be filled with the checksum of the input data.
> +
[Fiona] This is not correct - the checksum will always be in the op->output_chksum
The input_chksum field is for generating a checksum across the uncompressed data of multiple related ops

> +If you request a checksum for decompression, the checksum field in the operation
> +structure, ``op->output_chksum``, will be filled with the checksum of the output data.
> +
> +.. Note::
> +
> + For the compression case above, your output buffer will need to be large enough to hold the compressed
> data plus a scratchpad for the checksum at the end, the scratchpad is 8 bytes for CRC32 and 4 bytes for
> Adler32.
[Fiona] In the compression case is there no need for this scratchpad?

Re: [dpdk-dev] [PATCH 2/3] test/compress: add checksum tests

[Trahe, Fiona]

> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Lee Daly
> Sent: Tuesday, October 9, 2018 5:22 PM
> To: akhil.goyal@nxp.com
> Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> Subject: [dpdk-dev] [PATCH 2/3] test/compress: add checksum tests
> 
> This patch adds a test which examines what type of checksum the PMD
> supports, adler, crc32 or alder32_crc32
> and tests that feature if the PMD supports it.
> 
> Signed-off-by: Lee Daly <lee.daly@intel.com>

Nack
This isn't the latest code and has a compile issue.

[dpdk-dev] [PATCH v2 1/3] compress/isal: enable checksum support in driver

[Lee Daly]

This patch adds checksum support in the ISA-L  PMD for both compression
and decompression.
CRC32 is supported as well as Adler32.

Signed-off-by: Lee Daly <lee.daly@intel.com>
---
 drivers/compress/isal/isal_compress_pmd.c     | 80 ++++++++++++++++++++++-----
 drivers/compress/isal/isal_compress_pmd_ops.c |  4 +-
 2 files changed, 69 insertions(+), 15 deletions(-)

diff --git a/drivers/compress/isal/isal_compress_pmd.c b/drivers/compress/isal/isal_compress_pmd.c
index 9f1e968..b087ed8 100644
--- a/drivers/compress/isal/isal_compress_pmd.c
+++ b/drivers/compress/isal/isal_compress_pmd.c
@@ -16,6 +16,8 @@
 #define RTE_COMP_ISAL_LEVEL_ONE 1
 #define RTE_COMP_ISAL_LEVEL_TWO 2
 #define RTE_COMP_ISAL_LEVEL_THREE 3 /* Optimised for AVX512 & AVX2 only */
+#define CHKSUM_SZ_CRC 8
+#define CHKSUM_SZ_ADLER 4
 
 int isal_logtype_driver;
 
@@ -43,12 +45,6 @@ isal_comp_set_priv_xform_parameters(struct isal_priv_xform *priv_xform,
 		}
 		priv_xform->compress.algo = RTE_COMP_ALGO_DEFLATE;
 
-		/* Set private xform checksum - raw deflate by default */
-		if (xform->compress.chksum != RTE_COMP_CHECKSUM_NONE) {
-			ISAL_PMD_LOG(ERR, "Checksum not supported\n");
-			return -ENOTSUP;
-		}
-
 		/* Set private xform window size, 32K supported */
 		if (xform->compress.window_size == RTE_COMP_ISAL_WINDOW_SIZE)
 			priv_xform->compress.window_size =
@@ -77,6 +73,27 @@ isal_comp_set_priv_xform_parameters(struct isal_priv_xform *priv_xform,
 			return -ENOTSUP;
 		}
 
+		/* Set private xform checksum */
+		switch (xform->compress.chksum) {
+		/* Raw deflate by default */
+		case(RTE_COMP_CHECKSUM_NONE):
+			priv_xform->compress.chksum = IGZIP_DEFLATE;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32):
+			priv_xform->compress.chksum = IGZIP_GZIP_NO_HDR;
+			break;
+		case(RTE_COMP_CHECKSUM_ADLER32):
+			priv_xform->compress.chksum = IGZIP_ZLIB_NO_HDR;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32_ADLER32):
+			ISAL_PMD_LOG(ERR, "Combined CRC and ADLER checksum not"
+					" supported\n");
+			return -ENOTSUP;
+		default:
+			ISAL_PMD_LOG(ERR, "Checksum type not supported\n");
+			return -ENOTSUP;
+		}
+
 		/* Set private xform level.
 		 * Checking compliance with compressdev API, -1 <= level => 9
 		 */
@@ -170,9 +187,24 @@ isal_comp_set_priv_xform_parameters(struct isal_priv_xform *priv_xform,
 		}
 		priv_xform->decompress.algo = RTE_COMP_ALGO_DEFLATE;
 
-		/* Set private xform checksum - raw deflate by default */
-		if (xform->compress.chksum != RTE_COMP_CHECKSUM_NONE) {
-			ISAL_PMD_LOG(ERR, "Checksum not supported\n");
+		/* Set private xform checksum */
+		switch (xform->decompress.chksum) {
+		/* Raw deflate by default */
+		case(RTE_COMP_CHECKSUM_NONE):
+			priv_xform->decompress.chksum = ISAL_DEFLATE;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32):
+			priv_xform->decompress.chksum = ISAL_GZIP_NO_HDR_VER;
+			break;
+		case(RTE_COMP_CHECKSUM_ADLER32):
+			priv_xform->decompress.chksum = ISAL_ZLIB_NO_HDR_VER;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32_ADLER32):
+			ISAL_PMD_LOG(ERR, "Combined CRC and ADLER checksum not"
+					" supported\n");
+			return -ENOTSUP;
+		default:
+			ISAL_PMD_LOG(ERR, "Checksum type not supported\n");
 			return -ENOTSUP;
 		}
 
@@ -376,6 +408,9 @@ process_isal_deflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
 
 	qp->stream->level_buf = temp_level_buf;
 
+	/* Set Checksum flag */
+	qp->stream->gzip_flag = priv_xform->compress.chksum;
+
 	/* Stateless operation, input will be consumed in one go */
 	qp->stream->flush = NO_FLUSH;
 
@@ -459,8 +494,18 @@ process_isal_deflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
 			return ret;
 		}
 	}
+
 	op->consumed = qp->stream->total_in;
-	op->produced = qp->stream->total_out;
+	if (qp->stream->gzip_flag == IGZIP_DEFLATE) {
+		op->produced = qp->stream->total_out;
+	} else if (qp->stream->gzip_flag == IGZIP_ZLIB_NO_HDR) {
+		op->produced = qp->stream->total_out - CHKSUM_SZ_ADLER;
+		op->output_chksum = qp->stream->internal_state.crc + 1;
+	} else {
+		op->produced = qp->stream->total_out - CHKSUM_SZ_CRC;
+		op->output_chksum = qp->stream->internal_state.crc;
+	}
+
 	isal_deflate_reset(qp->stream);
 
 	return ret;
@@ -468,7 +513,8 @@ process_isal_deflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
 
 /* Stateless Decompression Function */
 static int
-process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp)
+process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
+		struct isal_priv_xform *priv_xform)
 {
 	int ret = 0;
 
@@ -477,6 +523,9 @@ process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp)
 	/* Initialize decompression state */
 	isal_inflate_init(qp->state);
 
+	/* Set Checksum flag */
+	qp->state->crc_flag = priv_xform->decompress.chksum;
+
 	if (op->m_src->pkt_len < (op->src.length + op->src.offset)) {
 		ISAL_PMD_LOG(ERR, "Input mbuf(s) not big enough.\n");
 		op->status = RTE_COMP_OP_STATUS_INVALID_ARGS;
@@ -531,13 +580,16 @@ process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp)
 			return -1;
 		}
 
-		if (ret != ISAL_DECOMP_OK) {
+		if (ret != ISAL_DECOMP_OK && ret != ISAL_END_INPUT) {
+			ISAL_PMD_LOG(ERR, "Decompression operation failed\n");
 			op->status = RTE_COMP_OP_STATUS_ERROR;
 			return ret;
 		}
 		op->consumed = op->src.length - qp->state->avail_in;
 	}
-		op->produced = qp->state->total_out;
+	op->produced = qp->state->total_out;
+	op->output_chksum = qp->state->crc;
+
 	isal_inflate_reset(qp->state);
 
 	return ret;
@@ -553,7 +605,7 @@ process_op(struct isal_comp_qp *qp, struct rte_comp_op *op,
 		process_isal_deflate(op, qp, priv_xform);
 		break;
 	case RTE_COMP_DECOMPRESS:
-		process_isal_inflate(op, qp);
+		process_isal_inflate(op, qp, priv_xform);
 		break;
 	default:
 		ISAL_PMD_LOG(ERR, "Operation Not Supported\n");
diff --git a/drivers/compress/isal/isal_compress_pmd_ops.c b/drivers/compress/isal/isal_compress_pmd_ops.c
index 41cade8..7b91849 100644
--- a/drivers/compress/isal/isal_compress_pmd_ops.c
+++ b/drivers/compress/isal/isal_compress_pmd_ops.c
@@ -17,7 +17,9 @@ static const struct rte_compressdev_capabilities isal_pmd_capabilities[] = {
 					RTE_COMP_FF_OOP_LB_IN_SGL_OUT |
 					RTE_COMP_FF_SHAREABLE_PRIV_XFORM |
 					RTE_COMP_FF_HUFFMAN_FIXED |
-					RTE_COMP_FF_HUFFMAN_DYNAMIC,
+					RTE_COMP_FF_HUFFMAN_DYNAMIC |
+					RTE_COMP_FF_CRC32_CHECKSUM |
+					RTE_COMP_FF_ADLER32_CHECKSUM,
 		.window_size = {
 			.min = 15,
 			.max = 15,
-- 
2.7.4

[dpdk-dev] [PATCH v2 2/3] test/compress: add checksum tests

[Lee Daly]

This patch adds a test which examines what type of checksum the PMD
supports, adler, crc32 or alder32_crc32
and tests that feature if the PMD supports it.

Signed-off-by: Lee Daly <lee.daly@intel.com>
---
 test/test/test_compressdev.c | 206 ++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 203 insertions(+), 3 deletions(-)

diff --git a/test/test/test_compressdev.c b/test/test/test_compressdev.c
index 4b98001..2ca4c91 100644
--- a/test/test/test_compressdev.c
+++ b/test/test/test_compressdev.c
@@ -37,6 +37,12 @@
 #define CACHE_SIZE 0
 #define OFFSET 800
 
+#define ZLIB_CRC_CHECKSUM_WINDOW_BITS 31
+#define ZLIB_HEADER_SIZE 2
+#define ZLIB_TRAILER_SIZE 4
+#define GZIP_HEADER_SIZE 10
+#define GZIP_TRAILER_SIZE 8
+
 const char *
 huffman_type_strings[] = {
 	[RTE_COMP_HUFFMAN_DEFAULT]	= "PMD default",
@@ -319,6 +325,10 @@ compress_zlib(struct rte_comp_op *op,
 	 * When doing raw DEFLATE, this number will be negative.
 	 */
 	window_bits = -(xform->compress.window_size);
+	if (xform->compress.chksum == RTE_COMP_CHECKSUM_ADLER32)
+		window_bits *= -1;
+	else if (xform->compress.chksum == RTE_COMP_CHECKSUM_CRC32)
+		window_bits = ZLIB_CRC_CHECKSUM_WINDOW_BITS;
 
 	comp_level = xform->compress.level;
 
@@ -422,8 +432,19 @@ compress_zlib(struct rte_comp_op *op,
 	}
 
 	op->consumed = stream.total_in;
-	op->produced = stream.total_out;
+	if (xform->compress.chksum == RTE_COMP_CHECKSUM_ADLER32) {
+		rte_pktmbuf_adj(op->m_dst, ZLIB_HEADER_SIZE);
+		op->produced = stream.total_out -
+				(ZLIB_HEADER_SIZE + ZLIB_TRAILER_SIZE);
+	} else if (xform->compress.chksum == RTE_COMP_CHECKSUM_CRC32) {
+		rte_pktmbuf_adj(op->m_dst, GZIP_HEADER_SIZE);
+		op->produced = stream.total_out -
+				(GZIP_HEADER_SIZE + GZIP_TRAILER_SIZE);
+	} else
+		op->produced = stream.total_out;
+
 	op->status = RTE_COMP_OP_STATUS_SUCCESS;
+	op->output_chksum = stream.adler;
 
 	deflateReset(&stream);
 
@@ -457,7 +478,6 @@ decompress_zlib(struct rte_comp_op *op,
 	 * When doing raw DEFLATE, this number will be negative.
 	 */
 	window_bits = -(xform->decompress.window_size);
-
 	ret = inflateInit2(&stream, window_bits);
 
 	if (ret != Z_OK) {
@@ -706,6 +726,7 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 	const struct rte_compressdev_capabilities *capa =
 		rte_compressdev_capability_get(0, RTE_COMP_ALGO_DEFLATE);
 	char *contig_buf = NULL;
+	uint64_t compress_checksum[num_bufs];
 
 	/* Initialize all arrays to NULL */
 	memset(uncomp_bufs, 0, sizeof(struct rte_mbuf *) * num_bufs);
@@ -896,6 +917,7 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 					&ops_processed[num_total_deqd], num_bufs);
 			num_total_deqd += num_deqd;
 			deqd_retries++;
+
 		} while (num_total_deqd < num_enqd);
 
 		deqd_retries = 0;
@@ -929,6 +951,8 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 			ops_processed[i]->consumed == 0 ? 0 :
 			(float)ops_processed[i]->produced /
 			ops_processed[i]->consumed * 100);
+		if (compress_xform->chksum != RTE_COMP_CHECKSUM_NONE)
+			compress_checksum[i] = ops_processed[i]->output_chksum;
 		ops[i] = NULL;
 	}
 
@@ -1166,11 +1190,23 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 		buf2 = rte_pktmbuf_read(ops_processed[i]->m_dst,
 				ops_processed[i]->dst.offset,
 				ops_processed[i]->produced, contig_buf);
-
 		if (compare_buffers(buf1, strlen(buf1) + 1,
 				buf2, ops_processed[i]->produced) < 0)
 			goto exit;
 
+		/* Test checksums */
+		if (compress_xforms[0]->compress.chksum !=
+				RTE_COMP_CHECKSUM_NONE) {
+			if (ops_processed[i]->output_chksum !=
+					compress_checksum[i]) {
+				RTE_LOG(ERR, USER1, "The checksums differ\n"
+			"Compression Checksum: %" PRIu64 "\tDecompression "
+			"Checksum: %" PRIu64 "\n", compress_checksum[i],
+			ops_processed[i]->output_chksum);
+				goto exit;
+			}
+		}
+
 		rte_free(contig_buf);
 		contig_buf = NULL;
 	}
@@ -1605,6 +1641,168 @@ test_compressdev_deflate_stateless_offset(void)
 	}
 
 	return TEST_SUCCESS;
+
+}
+
+static int
+test_compressdev_deflate_stateless_checksum(void)
+{
+	struct comp_testsuite_params *ts_params = &testsuite_params;
+	const char *test_buffer;
+	uint16_t i;
+	int ret;
+	const struct rte_compressdev_capabilities *capab;
+
+	capab = rte_compressdev_capability_get(0, RTE_COMP_ALGO_DEFLATE);
+	TEST_ASSERT(capab != NULL, "Failed to retrieve device capabilities");
+
+	/* Check if driver supports any checksum */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_CRC32_CHECKSUM) == 0 &&
+			(capab->comp_feature_flags &
+			RTE_COMP_FF_ADLER32_CHECKSUM) == 0 &&
+			(capab->comp_feature_flags &
+			RTE_COMP_FF_CRC32_ADLER32_CHECKSUM) == 0)
+		return -ENOTSUP;
+
+	struct rte_comp_xform *compress_xform =
+			rte_malloc(NULL, sizeof(struct rte_comp_xform), 0);
+	if (compress_xform == NULL) {
+		RTE_LOG(ERR, USER1, "Compress xform could not be created\n");
+		ret = TEST_FAILED;
+		goto exit;
+	}
+
+	memcpy(compress_xform, ts_params->def_comp_xform,
+			sizeof(struct rte_comp_xform));
+
+	struct rte_comp_xform *decompress_xform =
+			rte_malloc(NULL, sizeof(struct rte_comp_xform), 0);
+	if (decompress_xform == NULL) {
+		RTE_LOG(ERR, USER1, "Decompress xform could not be created\n");
+		ret = TEST_FAILED;
+		goto exit;
+	}
+
+	memcpy(decompress_xform, ts_params->def_decomp_xform,
+			sizeof(struct rte_comp_xform));
+
+	/* Check if driver supports crc32 checksum and test */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_CRC32_CHECKSUM)) {
+		compress_xform->compress.chksum = RTE_COMP_CHECKSUM_CRC32;
+		decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_CRC32;
+
+		for (i = 0; i < RTE_DIM(compress_test_bufs); i++) {
+			test_buffer = compress_test_bufs[i];
+
+			/* Generate zlib checksum and test against selected
+			 * drivers decompression checksum
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_COMPRESS,
+					0) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+
+			/* Generate compression and decompression
+			 * checksum of selected driver
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_NONE,
+					0) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+		}
+	}
+
+	/* Check if driver supports adler32 checksum and test */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_ADLER32_CHECKSUM)) {
+		compress_xform->compress.chksum = RTE_COMP_CHECKSUM_ADLER32;
+		decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_ADLER32;
+
+		for (i = 0; i < RTE_DIM(compress_test_bufs); i++) {
+			test_buffer = compress_test_bufs[i];
+
+			/* Generate zlib checksum and test against selected
+			 * drivers decompression checksum
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_COMPRESS,
+					0) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+			/* Generate compression and decompression
+			 * checksum of selected driver
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_NONE,
+					0) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+		}
+	}
+
+	/* Check if driver supports combined crc and adler checksum and test */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_CRC32_ADLER32_CHECKSUM)) {
+		compress_xform->compress.chksum =
+				RTE_COMP_CHECKSUM_CRC32_ADLER32;
+		decompress_xform->decompress.chksum =
+				RTE_COMP_CHECKSUM_CRC32_ADLER32;
+
+		for (i = 0; i < RTE_DIM(compress_test_bufs); i++) {
+			test_buffer = compress_test_bufs[i];
+
+			/* Generate compression and decompression
+			 * checksum of selected driver
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_NONE,
+					0) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+		}
+	}
+
+	ret = TEST_SUCCESS;
+
+exit:
+	rte_free(compress_xform);
+	rte_free(decompress_xform);
+	return ret;
 }
 
 static struct unit_test_suite compressdev_testsuite  = {
@@ -1628,6 +1826,8 @@ static struct unit_test_suite compressdev_testsuite  = {
 			test_compressdev_deflate_stateless_sgl),
 		TEST_CASE_ST(generic_ut_setup, generic_ut_teardown,
 			test_compressdev_deflate_stateless_offset),
+		TEST_CASE_ST(generic_ut_setup, generic_ut_teardown,
+			test_compressdev_deflate_stateless_checksum),
 		TEST_CASES_END() /**< NULL terminate unit test array */
 	}
 };
-- 
2.7.4

[dpdk-dev] [PATCH v2 3/3] doc: update ISA-L guide to reflect checksum support

[Lee Daly]

This updates the ISA-L compression driver guide on how to enable and use
checksums.

This also updates the compression drivers features matrix.
Will add to release notes once the 19.02.rst file is added.

Signed-off-by: Lee Daly <lee.daly@intel.com>
---
 doc/guides/compressdevs/features/isal.ini |  2 ++
 doc/guides/compressdevs/isal.rst          | 30 ++++++++++++++++++++++++++++--
 2 files changed, 30 insertions(+), 2 deletions(-)

diff --git a/doc/guides/compressdevs/features/isal.ini b/doc/guides/compressdevs/features/isal.ini
index 919cf70..e705031 100644
--- a/doc/guides/compressdevs/features/isal.ini
+++ b/doc/guides/compressdevs/features/isal.ini
@@ -12,5 +12,7 @@ OOP SGL In SGL Out = Y
 OOP SGL In LB  Out = Y
 OOP LB  In SGL Out = Y
 Deflate            = Y
+Adler32            = Y
+Crc32              = Y
 Fixed              = Y
 Dynamic            = Y
diff --git a/doc/guides/compressdevs/isal.rst b/doc/guides/compressdevs/isal.rst
index 3bc3022..af1f41f 100644
--- a/doc/guides/compressdevs/isal.rst
+++ b/doc/guides/compressdevs/isal.rst
@@ -27,6 +27,33 @@ Window size support:
 
     * 32K
 
+Checksum:
+
+    * CRC32
+    * ADLER32
+
+To enable a checksum in the driver, the compression and/or decompression xform
+structure, rte_comp_xform, must be filled with either of the CompressDev
+checksum flags supported. ::
+
+ compress_xform->compress.chksum = RTE_COMP_CHECKSUM_CRC32
+
+ decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_CRC32
+
+::
+
+ compress_xform->compress.chksum = RTE_COMP_CHECKSUM_ADLER32
+
+ decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_ADLER32
+
+If you request a checksum for compression or decompression,
+the checksum field in the operation structure,  ``op->output_chksum``,
+will be filled with the checksum.
+
+.. Note::
+
+ For the compression case above, your output buffer will need to be large enough to hold the compressed data plus a scratchpad for the checksum at the end, the scratchpad is 8 bytes for CRC32 and 4 bytes for Adler32.
+
 Level guide:
 
 The ISA-L levels have been mapped to somewhat correspond to the same ZLIB level,
@@ -75,13 +102,12 @@ As a result the level mappings from the API to the PMD are shown below.
  The above table only shows mapping when API calls for dynamic compression.
  For fixed compression, regardless of API level, internally ISA-L level 0 is always used.
 
+
 Limitations
 -----------
 
 * Compressdev level 0, no compression, is not supported.
 
-* Checksums will not be supported until future release.
-
 Installation
 ------------
 
-- 
2.7.4

Re: [dpdk-dev] [PATCH v2 2/3] test/compress: add checksum tests

[Jozwiak, TomaszX]

> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Lee Daly
> Sent: Wednesday, November 28, 2018 11:42 AM
> To: Trahe, Fiona <fiona.trahe@intel.com>; akhil.goyal@nxp.com
> Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> Subject: [dpdk-dev] [PATCH v2 2/3] test/compress: add checksum tests
> 
> This patch adds a test which examines what type of checksum the PMD
> supports, adler, crc32 or alder32_crc32 and tests that feature if the PMD
> supports it.
> 
> Signed-off-by: Lee Daly <lee.daly@intel.com>
> ---

Acked-by: Tomasz Jozwiak <tomaszx.jozwiak@intel.com>

Re: [dpdk-dev] [PATCH v2 1/3] compress/isal: enable checksum support in driver

[Trahe, Fiona]

> -----Original Message-----
> From: Daly, Lee
> Sent: Wednesday, November 28, 2018 3:42 AM
> To: Trahe, Fiona <fiona.trahe@intel.com>; akhil.goyal@nxp.com
> Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> Subject: [PATCH v2 1/3] compress/isal: enable checksum support in driver
> 
> This patch adds checksum support in the ISA-L  PMD for both compression
> and decompression.
> CRC32 is supported as well as Adler32.
> 
> Signed-off-by: Lee Daly <lee.daly@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>

Re: [dpdk-dev] [PATCH v2 2/3] test/compress: add checksum tests

[Trahe, Fiona]

> -----Original Message-----
> From: Daly, Lee
> Sent: Wednesday, November 28, 2018 3:42 AM
> To: Trahe, Fiona <fiona.trahe@intel.com>; akhil.goyal@nxp.com
> Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> Subject: [PATCH v2 2/3] test/compress: add checksum tests
> 
> This patch adds a test which examines what type of checksum the PMD
> supports, adler, crc32 or alder32_crc32
> and tests that feature if the PMD supports it.
> 
> Signed-off-by: Lee Daly <lee.daly@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>

Re: [dpdk-dev] [PATCH v2 3/3] doc: update ISA-L guide to reflect checksum support

[Trahe, Fiona]

> -----Original Message-----
> From: Daly, Lee
> Sent: Wednesday, November 28, 2018 3:42 AM
> To: Trahe, Fiona <fiona.trahe@intel.com>; akhil.goyal@nxp.com
> Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> Subject: [PATCH v2 3/3] doc: update ISA-L guide to reflect checksum support
> 
> This updates the ISA-L compression driver guide on how to enable and use
> checksums.
> 
> This also updates the compression drivers features matrix.
> Will add to release notes once the 19.02.rst file is added.
> 
> Signed-off-by: Lee Daly <lee.daly@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>

[dpdk-dev] [PATCH v3 1/3] compress/isal: enable checksum support in driver

[Lee Daly]

This patch adds checksum support in the ISA-L  PMD for both compression
and decompression.
CRC32 is supported as well as Adler32.

V2:
Documentation Changes
V3:
Added Release note

Signed-off-by: Lee Daly <lee.daly@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
---
 drivers/compress/isal/isal_compress_pmd.c     | 80 ++++++++++++++++++++++-----
 drivers/compress/isal/isal_compress_pmd_ops.c |  4 +-
 2 files changed, 69 insertions(+), 15 deletions(-)

diff --git a/drivers/compress/isal/isal_compress_pmd.c b/drivers/compress/isal/isal_compress_pmd.c
index 9f1e968..b087ed8 100644
--- a/drivers/compress/isal/isal_compress_pmd.c
+++ b/drivers/compress/isal/isal_compress_pmd.c
@@ -16,6 +16,8 @@
 #define RTE_COMP_ISAL_LEVEL_ONE 1
 #define RTE_COMP_ISAL_LEVEL_TWO 2
 #define RTE_COMP_ISAL_LEVEL_THREE 3 /* Optimised for AVX512 & AVX2 only */
+#define CHKSUM_SZ_CRC 8
+#define CHKSUM_SZ_ADLER 4
 
 int isal_logtype_driver;
 
@@ -43,12 +45,6 @@ isal_comp_set_priv_xform_parameters(struct isal_priv_xform *priv_xform,
 		}
 		priv_xform->compress.algo = RTE_COMP_ALGO_DEFLATE;
 
-		/* Set private xform checksum - raw deflate by default */
-		if (xform->compress.chksum != RTE_COMP_CHECKSUM_NONE) {
-			ISAL_PMD_LOG(ERR, "Checksum not supported\n");
-			return -ENOTSUP;
-		}
-
 		/* Set private xform window size, 32K supported */
 		if (xform->compress.window_size == RTE_COMP_ISAL_WINDOW_SIZE)
 			priv_xform->compress.window_size =
@@ -77,6 +73,27 @@ isal_comp_set_priv_xform_parameters(struct isal_priv_xform *priv_xform,
 			return -ENOTSUP;
 		}
 
+		/* Set private xform checksum */
+		switch (xform->compress.chksum) {
+		/* Raw deflate by default */
+		case(RTE_COMP_CHECKSUM_NONE):
+			priv_xform->compress.chksum = IGZIP_DEFLATE;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32):
+			priv_xform->compress.chksum = IGZIP_GZIP_NO_HDR;
+			break;
+		case(RTE_COMP_CHECKSUM_ADLER32):
+			priv_xform->compress.chksum = IGZIP_ZLIB_NO_HDR;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32_ADLER32):
+			ISAL_PMD_LOG(ERR, "Combined CRC and ADLER checksum not"
+					" supported\n");
+			return -ENOTSUP;
+		default:
+			ISAL_PMD_LOG(ERR, "Checksum type not supported\n");
+			return -ENOTSUP;
+		}
+
 		/* Set private xform level.
 		 * Checking compliance with compressdev API, -1 <= level => 9
 		 */
@@ -170,9 +187,24 @@ isal_comp_set_priv_xform_parameters(struct isal_priv_xform *priv_xform,
 		}
 		priv_xform->decompress.algo = RTE_COMP_ALGO_DEFLATE;
 
-		/* Set private xform checksum - raw deflate by default */
-		if (xform->compress.chksum != RTE_COMP_CHECKSUM_NONE) {
-			ISAL_PMD_LOG(ERR, "Checksum not supported\n");
+		/* Set private xform checksum */
+		switch (xform->decompress.chksum) {
+		/* Raw deflate by default */
+		case(RTE_COMP_CHECKSUM_NONE):
+			priv_xform->decompress.chksum = ISAL_DEFLATE;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32):
+			priv_xform->decompress.chksum = ISAL_GZIP_NO_HDR_VER;
+			break;
+		case(RTE_COMP_CHECKSUM_ADLER32):
+			priv_xform->decompress.chksum = ISAL_ZLIB_NO_HDR_VER;
+			break;
+		case(RTE_COMP_CHECKSUM_CRC32_ADLER32):
+			ISAL_PMD_LOG(ERR, "Combined CRC and ADLER checksum not"
+					" supported\n");
+			return -ENOTSUP;
+		default:
+			ISAL_PMD_LOG(ERR, "Checksum type not supported\n");
 			return -ENOTSUP;
 		}
 
@@ -376,6 +408,9 @@ process_isal_deflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
 
 	qp->stream->level_buf = temp_level_buf;
 
+	/* Set Checksum flag */
+	qp->stream->gzip_flag = priv_xform->compress.chksum;
+
 	/* Stateless operation, input will be consumed in one go */
 	qp->stream->flush = NO_FLUSH;
 
@@ -459,8 +494,18 @@ process_isal_deflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
 			return ret;
 		}
 	}
+
 	op->consumed = qp->stream->total_in;
-	op->produced = qp->stream->total_out;
+	if (qp->stream->gzip_flag == IGZIP_DEFLATE) {
+		op->produced = qp->stream->total_out;
+	} else if (qp->stream->gzip_flag == IGZIP_ZLIB_NO_HDR) {
+		op->produced = qp->stream->total_out - CHKSUM_SZ_ADLER;
+		op->output_chksum = qp->stream->internal_state.crc + 1;
+	} else {
+		op->produced = qp->stream->total_out - CHKSUM_SZ_CRC;
+		op->output_chksum = qp->stream->internal_state.crc;
+	}
+
 	isal_deflate_reset(qp->stream);
 
 	return ret;
@@ -468,7 +513,8 @@ process_isal_deflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
 
 /* Stateless Decompression Function */
 static int
-process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp)
+process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp,
+		struct isal_priv_xform *priv_xform)
 {
 	int ret = 0;
 
@@ -477,6 +523,9 @@ process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp)
 	/* Initialize decompression state */
 	isal_inflate_init(qp->state);
 
+	/* Set Checksum flag */
+	qp->state->crc_flag = priv_xform->decompress.chksum;
+
 	if (op->m_src->pkt_len < (op->src.length + op->src.offset)) {
 		ISAL_PMD_LOG(ERR, "Input mbuf(s) not big enough.\n");
 		op->status = RTE_COMP_OP_STATUS_INVALID_ARGS;
@@ -531,13 +580,16 @@ process_isal_inflate(struct rte_comp_op *op, struct isal_comp_qp *qp)
 			return -1;
 		}
 
-		if (ret != ISAL_DECOMP_OK) {
+		if (ret != ISAL_DECOMP_OK && ret != ISAL_END_INPUT) {
+			ISAL_PMD_LOG(ERR, "Decompression operation failed\n");
 			op->status = RTE_COMP_OP_STATUS_ERROR;
 			return ret;
 		}
 		op->consumed = op->src.length - qp->state->avail_in;
 	}
-		op->produced = qp->state->total_out;
+	op->produced = qp->state->total_out;
+	op->output_chksum = qp->state->crc;
+
 	isal_inflate_reset(qp->state);
 
 	return ret;
@@ -553,7 +605,7 @@ process_op(struct isal_comp_qp *qp, struct rte_comp_op *op,
 		process_isal_deflate(op, qp, priv_xform);
 		break;
 	case RTE_COMP_DECOMPRESS:
-		process_isal_inflate(op, qp);
+		process_isal_inflate(op, qp, priv_xform);
 		break;
 	default:
 		ISAL_PMD_LOG(ERR, "Operation Not Supported\n");
diff --git a/drivers/compress/isal/isal_compress_pmd_ops.c b/drivers/compress/isal/isal_compress_pmd_ops.c
index 41cade8..7b91849 100644
--- a/drivers/compress/isal/isal_compress_pmd_ops.c
+++ b/drivers/compress/isal/isal_compress_pmd_ops.c
@@ -17,7 +17,9 @@ static const struct rte_compressdev_capabilities isal_pmd_capabilities[] = {
 					RTE_COMP_FF_OOP_LB_IN_SGL_OUT |
 					RTE_COMP_FF_SHAREABLE_PRIV_XFORM |
 					RTE_COMP_FF_HUFFMAN_FIXED |
-					RTE_COMP_FF_HUFFMAN_DYNAMIC,
+					RTE_COMP_FF_HUFFMAN_DYNAMIC |
+					RTE_COMP_FF_CRC32_CHECKSUM |
+					RTE_COMP_FF_ADLER32_CHECKSUM,
 		.window_size = {
 			.min = 15,
 			.max = 15,
-- 
2.7.4

[dpdk-dev] [PATCH v3 2/3] test/compress: add checksum tests

[Lee Daly]

This patch adds a test which examines what type of checksum the PMD
supports, adler, crc32 or alder32_crc32
and tests that feature if the PMD supports it.

V2:
Documentation Changes
V3:
Added Release note

Signed-off-by: Lee Daly <lee.daly@intel.com>
Acked-by: Tomasz Jozwiak <tomasz.jozwiak@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
---
 test/test/test_compressdev.c | 206 ++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 203 insertions(+), 3 deletions(-)

diff --git a/test/test/test_compressdev.c b/test/test/test_compressdev.c
index 4b98001..2ca4c91 100644
--- a/test/test/test_compressdev.c
+++ b/test/test/test_compressdev.c
@@ -37,6 +37,12 @@
 #define CACHE_SIZE 0
 #define OFFSET 800
 
+#define ZLIB_CRC_CHECKSUM_WINDOW_BITS 31
+#define ZLIB_HEADER_SIZE 2
+#define ZLIB_TRAILER_SIZE 4
+#define GZIP_HEADER_SIZE 10
+#define GZIP_TRAILER_SIZE 8
+
 const char *
 huffman_type_strings[] = {
 	[RTE_COMP_HUFFMAN_DEFAULT]	= "PMD default",
@@ -319,6 +325,10 @@ compress_zlib(struct rte_comp_op *op,
 	 * When doing raw DEFLATE, this number will be negative.
 	 */
 	window_bits = -(xform->compress.window_size);
+	if (xform->compress.chksum == RTE_COMP_CHECKSUM_ADLER32)
+		window_bits *= -1;
+	else if (xform->compress.chksum == RTE_COMP_CHECKSUM_CRC32)
+		window_bits = ZLIB_CRC_CHECKSUM_WINDOW_BITS;
 
 	comp_level = xform->compress.level;
 
@@ -422,8 +432,19 @@ compress_zlib(struct rte_comp_op *op,
 	}
 
 	op->consumed = stream.total_in;
-	op->produced = stream.total_out;
+	if (xform->compress.chksum == RTE_COMP_CHECKSUM_ADLER32) {
+		rte_pktmbuf_adj(op->m_dst, ZLIB_HEADER_SIZE);
+		op->produced = stream.total_out -
+				(ZLIB_HEADER_SIZE + ZLIB_TRAILER_SIZE);
+	} else if (xform->compress.chksum == RTE_COMP_CHECKSUM_CRC32) {
+		rte_pktmbuf_adj(op->m_dst, GZIP_HEADER_SIZE);
+		op->produced = stream.total_out -
+				(GZIP_HEADER_SIZE + GZIP_TRAILER_SIZE);
+	} else
+		op->produced = stream.total_out;
+
 	op->status = RTE_COMP_OP_STATUS_SUCCESS;
+	op->output_chksum = stream.adler;
 
 	deflateReset(&stream);
 
@@ -457,7 +478,6 @@ decompress_zlib(struct rte_comp_op *op,
 	 * When doing raw DEFLATE, this number will be negative.
 	 */
 	window_bits = -(xform->decompress.window_size);
-
 	ret = inflateInit2(&stream, window_bits);
 
 	if (ret != Z_OK) {
@@ -706,6 +726,7 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 	const struct rte_compressdev_capabilities *capa =
 		rte_compressdev_capability_get(0, RTE_COMP_ALGO_DEFLATE);
 	char *contig_buf = NULL;
+	uint64_t compress_checksum[num_bufs];
 
 	/* Initialize all arrays to NULL */
 	memset(uncomp_bufs, 0, sizeof(struct rte_mbuf *) * num_bufs);
@@ -896,6 +917,7 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 					&ops_processed[num_total_deqd], num_bufs);
 			num_total_deqd += num_deqd;
 			deqd_retries++;
+
 		} while (num_total_deqd < num_enqd);
 
 		deqd_retries = 0;
@@ -929,6 +951,8 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 			ops_processed[i]->consumed == 0 ? 0 :
 			(float)ops_processed[i]->produced /
 			ops_processed[i]->consumed * 100);
+		if (compress_xform->chksum != RTE_COMP_CHECKSUM_NONE)
+			compress_checksum[i] = ops_processed[i]->output_chksum;
 		ops[i] = NULL;
 	}
 
@@ -1166,11 +1190,23 @@ test_deflate_comp_decomp(const char * const test_bufs[],
 		buf2 = rte_pktmbuf_read(ops_processed[i]->m_dst,
 				ops_processed[i]->dst.offset,
 				ops_processed[i]->produced, contig_buf);
-
 		if (compare_buffers(buf1, strlen(buf1) + 1,
 				buf2, ops_processed[i]->produced) < 0)
 			goto exit;
 
+		/* Test checksums */
+		if (compress_xforms[0]->compress.chksum !=
+				RTE_COMP_CHECKSUM_NONE) {
+			if (ops_processed[i]->output_chksum !=
+					compress_checksum[i]) {
+				RTE_LOG(ERR, USER1, "The checksums differ\n"
+			"Compression Checksum: %" PRIu64 "\tDecompression "
+			"Checksum: %" PRIu64 "\n", compress_checksum[i],
+			ops_processed[i]->output_chksum);
+				goto exit;
+			}
+		}
+
 		rte_free(contig_buf);
 		contig_buf = NULL;
 	}
@@ -1605,6 +1641,168 @@ test_compressdev_deflate_stateless_offset(void)
 	}
 
 	return TEST_SUCCESS;
+
+}
+
+static int
+test_compressdev_deflate_stateless_checksum(void)
+{
+	struct comp_testsuite_params *ts_params = &testsuite_params;
+	const char *test_buffer;
+	uint16_t i;
+	int ret;
+	const struct rte_compressdev_capabilities *capab;
+
+	capab = rte_compressdev_capability_get(0, RTE_COMP_ALGO_DEFLATE);
+	TEST_ASSERT(capab != NULL, "Failed to retrieve device capabilities");
+
+	/* Check if driver supports any checksum */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_CRC32_CHECKSUM) == 0 &&
+			(capab->comp_feature_flags &
+			RTE_COMP_FF_ADLER32_CHECKSUM) == 0 &&
+			(capab->comp_feature_flags &
+			RTE_COMP_FF_CRC32_ADLER32_CHECKSUM) == 0)
+		return -ENOTSUP;
+
+	struct rte_comp_xform *compress_xform =
+			rte_malloc(NULL, sizeof(struct rte_comp_xform), 0);
+	if (compress_xform == NULL) {
+		RTE_LOG(ERR, USER1, "Compress xform could not be created\n");
+		ret = TEST_FAILED;
+		goto exit;
+	}
+
+	memcpy(compress_xform, ts_params->def_comp_xform,
+			sizeof(struct rte_comp_xform));
+
+	struct rte_comp_xform *decompress_xform =
+			rte_malloc(NULL, sizeof(struct rte_comp_xform), 0);
+	if (decompress_xform == NULL) {
+		RTE_LOG(ERR, USER1, "Decompress xform could not be created\n");
+		ret = TEST_FAILED;
+		goto exit;
+	}
+
+	memcpy(decompress_xform, ts_params->def_decomp_xform,
+			sizeof(struct rte_comp_xform));
+
+	/* Check if driver supports crc32 checksum and test */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_CRC32_CHECKSUM)) {
+		compress_xform->compress.chksum = RTE_COMP_CHECKSUM_CRC32;
+		decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_CRC32;
+
+		for (i = 0; i < RTE_DIM(compress_test_bufs); i++) {
+			test_buffer = compress_test_bufs[i];
+
+			/* Generate zlib checksum and test against selected
+			 * drivers decompression checksum
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_COMPRESS,
+					0) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+
+			/* Generate compression and decompression
+			 * checksum of selected driver
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_NONE,
+					0) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+		}
+	}
+
+	/* Check if driver supports adler32 checksum and test */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_ADLER32_CHECKSUM)) {
+		compress_xform->compress.chksum = RTE_COMP_CHECKSUM_ADLER32;
+		decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_ADLER32;
+
+		for (i = 0; i < RTE_DIM(compress_test_bufs); i++) {
+			test_buffer = compress_test_bufs[i];
+
+			/* Generate zlib checksum and test against selected
+			 * drivers decompression checksum
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_COMPRESS,
+					0) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+			/* Generate compression and decompression
+			 * checksum of selected driver
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_NONE,
+					0) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+		}
+	}
+
+	/* Check if driver supports combined crc and adler checksum and test */
+	if ((capab->comp_feature_flags & RTE_COMP_FF_CRC32_ADLER32_CHECKSUM)) {
+		compress_xform->compress.chksum =
+				RTE_COMP_CHECKSUM_CRC32_ADLER32;
+		decompress_xform->decompress.chksum =
+				RTE_COMP_CHECKSUM_CRC32_ADLER32;
+
+		for (i = 0; i < RTE_DIM(compress_test_bufs); i++) {
+			test_buffer = compress_test_bufs[i];
+
+			/* Generate compression and decompression
+			 * checksum of selected driver
+			 */
+			if (test_deflate_comp_decomp(&test_buffer, 1,
+					&i,
+					&compress_xform,
+					&decompress_xform,
+					1,
+					RTE_COMP_OP_STATELESS,
+					0,
+					ZLIB_NONE,
+					0) < 0) {
+				ret = TEST_FAILED;
+				goto exit;
+			}
+		}
+	}
+
+	ret = TEST_SUCCESS;
+
+exit:
+	rte_free(compress_xform);
+	rte_free(decompress_xform);
+	return ret;
 }
 
 static struct unit_test_suite compressdev_testsuite  = {
@@ -1628,6 +1826,8 @@ static struct unit_test_suite compressdev_testsuite  = {
 			test_compressdev_deflate_stateless_sgl),
 		TEST_CASE_ST(generic_ut_setup, generic_ut_teardown,
 			test_compressdev_deflate_stateless_offset),
+		TEST_CASE_ST(generic_ut_setup, generic_ut_teardown,
+			test_compressdev_deflate_stateless_checksum),
 		TEST_CASES_END() /**< NULL terminate unit test array */
 	}
 };
-- 
2.7.4

[dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to reflect checksum support

[Lee Daly]

This updates the ISA-L compression driver guide on how to enable and use
checksums.

This also updates the compression drivers features matrix.

V2:
Documentation Changes
V3:
Added Release note

Signed-off-by: Lee Daly <lee.daly@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
---
 doc/guides/compressdevs/features/isal.ini |  2 ++
 doc/guides/compressdevs/isal.rst          | 30 ++++++++++++++++++++++++++++--
 doc/guides/rel_notes/release_19_02.rst    |  5 +++++
 3 files changed, 35 insertions(+), 2 deletions(-)

diff --git a/doc/guides/compressdevs/features/isal.ini b/doc/guides/compressdevs/features/isal.ini
index 919cf70..e705031 100644
--- a/doc/guides/compressdevs/features/isal.ini
+++ b/doc/guides/compressdevs/features/isal.ini
@@ -12,5 +12,7 @@ OOP SGL In SGL Out = Y
 OOP SGL In LB  Out = Y
 OOP LB  In SGL Out = Y
 Deflate            = Y
+Adler32            = Y
+Crc32              = Y
 Fixed              = Y
 Dynamic            = Y
diff --git a/doc/guides/compressdevs/isal.rst b/doc/guides/compressdevs/isal.rst
index 3bc3022..af1f41f 100644
--- a/doc/guides/compressdevs/isal.rst
+++ b/doc/guides/compressdevs/isal.rst
@@ -27,6 +27,33 @@ Window size support:
 
     * 32K
 
+Checksum:
+
+    * CRC32
+    * ADLER32
+
+To enable a checksum in the driver, the compression and/or decompression xform
+structure, rte_comp_xform, must be filled with either of the CompressDev
+checksum flags supported. ::
+
+ compress_xform->compress.chksum = RTE_COMP_CHECKSUM_CRC32
+
+ decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_CRC32
+
+::
+
+ compress_xform->compress.chksum = RTE_COMP_CHECKSUM_ADLER32
+
+ decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_ADLER32
+
+If you request a checksum for compression or decompression,
+the checksum field in the operation structure,  ``op->output_chksum``,
+will be filled with the checksum.
+
+.. Note::
+
+ For the compression case above, your output buffer will need to be large enough to hold the compressed data plus a scratchpad for the checksum at the end, the scratchpad is 8 bytes for CRC32 and 4 bytes for Adler32.
+
 Level guide:
 
 The ISA-L levels have been mapped to somewhat correspond to the same ZLIB level,
@@ -75,13 +102,12 @@ As a result the level mappings from the API to the PMD are shown below.
  The above table only shows mapping when API calls for dynamic compression.
  For fixed compression, regardless of API level, internally ISA-L level 0 is always used.
 
+
 Limitations
 -----------
 
 * Compressdev level 0, no compression, is not supported.
 
-* Checksums will not be supported until future release.
-
 Installation
 ------------
 
diff --git a/doc/guides/rel_notes/release_19_02.rst b/doc/guides/rel_notes/release_19_02.rst
index a94fa86..3a4d264 100644
--- a/doc/guides/rel_notes/release_19_02.rst
+++ b/doc/guides/rel_notes/release_19_02.rst
@@ -54,6 +54,11 @@ New Features
      Also, make sure to start the actual text at the margin.
      =========================================================
 
+   * **Enabled checksum support in the ISA-L compressdev driver.**
+
+     Added support for both adler and crc32 checksums in the ISA-L PMD.
+     This aids data integrity across both compression and decompression.
+
 
 Removed Items
 -------------
-- 
2.7.4

Re: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to reflect checksum support

[Varghese, Vipin]

Hi Lee,

A humble suggestion being shared for document update, Based on DPDK 19.02-rc1 release both code and associated document update is to be in single patch file.

Note: I am not fully sure how this is applicable to 'isal.ini and isal.rst'. It will be good to have a check.

Thanks
Vipin Varghese

> -----Original Message-----
> From: dev <dev-bounces@dpdk.org> On Behalf Of Lee Daly
> Sent: Thursday, December 13, 2018 4:13 PM
> To: akhil.goyal@nxp.com
> Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> Subject: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to reflect checksum
> support
> 
> This updates the ISA-L compression driver guide on how to enable and use
> checksums.
> 
> This also updates the compression drivers features matrix.
> 
> V2:
> Documentation Changes
> V3:
> Added Release note
> 
> Signed-off-by: Lee Daly <lee.daly@intel.com>
> Acked-by: Fiona Trahe <fiona.trahe@intel.com>
> ---
>  doc/guides/compressdevs/features/isal.ini |  2 ++
>  doc/guides/compressdevs/isal.rst          | 30 ++++++++++++++++++++++++++++-
> -
>  doc/guides/rel_notes/release_19_02.rst    |  5 +++++
>  3 files changed, 35 insertions(+), 2 deletions(-)
> 
> diff --git a/doc/guides/compressdevs/features/isal.ini
> b/doc/guides/compressdevs/features/isal.ini
> index 919cf70..e705031 100644
> --- a/doc/guides/compressdevs/features/isal.ini
> +++ b/doc/guides/compressdevs/features/isal.ini
> @@ -12,5 +12,7 @@ OOP SGL In SGL Out = Y  OOP SGL In LB  Out = Y  OOP LB  In
> SGL Out = Y
>  Deflate            = Y
> +Adler32            = Y
> +Crc32              = Y
>  Fixed              = Y
>  Dynamic            = Y
> diff --git a/doc/guides/compressdevs/isal.rst b/doc/guides/compressdevs/isal.rst
> index 3bc3022..af1f41f 100644
> --- a/doc/guides/compressdevs/isal.rst
> +++ b/doc/guides/compressdevs/isal.rst
> @@ -27,6 +27,33 @@ Window size support:
> 
>      * 32K
> 
> +Checksum:
> +
> +    * CRC32
> +    * ADLER32
> +
> +To enable a checksum in the driver, the compression and/or
> +decompression xform structure, rte_comp_xform, must be filled with
> +either of the CompressDev checksum flags supported. ::
> +
> + compress_xform->compress.chksum = RTE_COMP_CHECKSUM_CRC32
> +
> + decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_CRC32
> +
> +::
> +
> + compress_xform->compress.chksum = RTE_COMP_CHECKSUM_ADLER32
> +
> + decompress_xform->decompress.chksum = RTE_COMP_CHECKSUM_ADLER32
> +
> +If you request a checksum for compression or decompression, the
> +checksum field in the operation structure,  ``op->output_chksum``, will
> +be filled with the checksum.
> +
> +.. Note::
> +
> + For the compression case above, your output buffer will need to be large
> enough to hold the compressed data plus a scratchpad for the checksum at the
> end, the scratchpad is 8 bytes for CRC32 and 4 bytes for Adler32.
> +
>  Level guide:
> 
>  The ISA-L levels have been mapped to somewhat correspond to the same ZLIB
> level, @@ -75,13 +102,12 @@ As a result the level mappings from the API to the
> PMD are shown below.
>   The above table only shows mapping when API calls for dynamic compression.
>   For fixed compression, regardless of API level, internally ISA-L level 0 is always
> used.
> 
> +
>  Limitations
>  -----------
> 
>  * Compressdev level 0, no compression, is not supported.
> 
> -* Checksums will not be supported until future release.
> -
>  Installation
>  ------------
> 
> diff --git a/doc/guides/rel_notes/release_19_02.rst
> b/doc/guides/rel_notes/release_19_02.rst
> index a94fa86..3a4d264 100644
> --- a/doc/guides/rel_notes/release_19_02.rst
> +++ b/doc/guides/rel_notes/release_19_02.rst
> @@ -54,6 +54,11 @@ New Features
>       Also, make sure to start the actual text at the margin.
>       =========================================================
> 
> +   * **Enabled checksum support in the ISA-L compressdev driver.**
> +
> +     Added support for both adler and crc32 checksums in the ISA-L PMD.
> +     This aids data integrity across both compression and decompression.
> +
> 
>  Removed Items
>  -------------
> --
> 2.7.4

Re: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to reflect checksum support

[Daly, Lee]

Hi Vipin, thanks for your suggestion. 
I will send another version with the change.
/Lee.

> -----Original Message-----
> From: Varghese, Vipin
> Sent: Friday, December 28, 2018 5:05 AM
> To: Daly, Lee <lee.daly@intel.com>; akhil.goyal@nxp.com
> Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> Subject: RE: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to reflect
> checksum support
> 
> Hi Lee,
> 
> A humble suggestion being shared for document update, Based on DPDK
> 19.02-rc1 release both code and associated document update is to be in
> single patch file.
> 
> Note: I am not fully sure how this is applicable to 'isal.ini and isal.rst'. It will be
> good to have a check.
> 
> Thanks
> Vipin Varghese
> 
> > -----Original Message-----
> > From: dev <dev-bounces@dpdk.org> On Behalf Of Lee Daly
> > Sent: Thursday, December 13, 2018 4:13 PM
> > To: akhil.goyal@nxp.com
> > Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> > Subject: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to reflect
> > checksum support
> >
> > This updates the ISA-L compression driver guide on how to enable and
> > use checksums.
> >
> > This also updates the compression drivers features matrix.
> >
> > V2:
> > Documentation Changes
> > V3:
> > Added Release note
> >
> > Signed-off-by: Lee Daly <lee.daly@intel.com>
> > Acked-by: Fiona Trahe <fiona.trahe@intel.com>
> > ---
> >  doc/guides/compressdevs/features/isal.ini |  2 ++
> >  doc/guides/compressdevs/isal.rst          | 30
> ++++++++++++++++++++++++++++-
> > -
> >  doc/guides/rel_notes/release_19_02.rst    |  5 +++++
> >  3 files changed, 35 insertions(+), 2 deletions(-)
> >
> > diff --git a/doc/guides/compressdevs/features/isal.ini
> > b/doc/guides/compressdevs/features/isal.ini
> > index 919cf70..e705031 100644
> > --- a/doc/guides/compressdevs/features/isal.ini
> > +++ b/doc/guides/compressdevs/features/isal.ini
> > @@ -12,5 +12,7 @@ OOP SGL In SGL Out = Y  OOP SGL In LB  Out = Y  OOP
> > LB  In SGL Out = Y
> >  Deflate            = Y
> > +Adler32            = Y
> > +Crc32              = Y
> >  Fixed              = Y
> >  Dynamic            = Y
> > diff --git a/doc/guides/compressdevs/isal.rst
> > b/doc/guides/compressdevs/isal.rst
> > index 3bc3022..af1f41f 100644
> > --- a/doc/guides/compressdevs/isal.rst
> > +++ b/doc/guides/compressdevs/isal.rst
> > @@ -27,6 +27,33 @@ Window size support:
> >
> >      * 32K
> >
> > +Checksum:
> > +
> > +    * CRC32
> > +    * ADLER32
> > +
> > +To enable a checksum in the driver, the compression and/or
> > +decompression xform structure, rte_comp_xform, must be filled with
> > +either of the CompressDev checksum flags supported. ::
> > +
> > + compress_xform->compress.chksum = RTE_COMP_CHECKSUM_CRC32
> > +
> > + decompress_xform->decompress.chksum =
> RTE_COMP_CHECKSUM_CRC32
> > +
> > +::
> > +
> > + compress_xform->compress.chksum =
> RTE_COMP_CHECKSUM_ADLER32
> > +
> > + decompress_xform->decompress.chksum =
> RTE_COMP_CHECKSUM_ADLER32
> > +
> > +If you request a checksum for compression or decompression, the
> > +checksum field in the operation structure,  ``op->output_chksum``,
> > +will be filled with the checksum.
> > +
> > +.. Note::
> > +
> > + For the compression case above, your output buffer will need to be
> > + large
> > enough to hold the compressed data plus a scratchpad for the checksum
> > at the end, the scratchpad is 8 bytes for CRC32 and 4 bytes for Adler32.
> > +
> >  Level guide:
> >
> >  The ISA-L levels have been mapped to somewhat correspond to the same
> > ZLIB level, @@ -75,13 +102,12 @@ As a result the level mappings from
> > the API to the PMD are shown below.
> >   The above table only shows mapping when API calls for dynamic
> compression.
> >   For fixed compression, regardless of API level, internally ISA-L
> > level 0 is always used.
> >
> > +
> >  Limitations
> >  -----------
> >
> >  * Compressdev level 0, no compression, is not supported.
> >
> > -* Checksums will not be supported until future release.
> > -
> >  Installation
> >  ------------
> >
> > diff --git a/doc/guides/rel_notes/release_19_02.rst
> > b/doc/guides/rel_notes/release_19_02.rst
> > index a94fa86..3a4d264 100644
> > --- a/doc/guides/rel_notes/release_19_02.rst
> > +++ b/doc/guides/rel_notes/release_19_02.rst
> > @@ -54,6 +54,11 @@ New Features
> >       Also, make sure to start the actual text at the margin.
> >
> =========================================================
> >
> > +   * **Enabled checksum support in the ISA-L compressdev driver.**
> > +
> > +     Added support for both adler and crc32 checksums in the ISA-L PMD.
> > +     This aids data integrity across both compression and decompression.
> > +
> >
> >  Removed Items
> >  -------------
> > --
> > 2.7.4

Re: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to reflect checksum support

[Varghese, Vipin]

Thanks Lee for understanding

> -----Original Message-----
> From: Daly, Lee
> Sent: Monday, January 7, 2019 4:07 PM
> To: Varghese, Vipin <vipin.varghese@intel.com>; akhil.goyal@nxp.com
> Cc: dev@dpdk.org
> Subject: RE: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to reflect
> checksum support
> 
> Hi Vipin, thanks for your suggestion.
> I will send another version with the change.
> /Lee.
> 
> > -----Original Message-----
> > From: Varghese, Vipin
> > Sent: Friday, December 28, 2018 5:05 AM
> > To: Daly, Lee <lee.daly@intel.com>; akhil.goyal@nxp.com
> > Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> > Subject: RE: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to
> > reflect checksum support
> >
> > Hi Lee,
> >
> > A humble suggestion being shared for document update, Based on DPDK
> > 19.02-rc1 release both code and associated document update is to be in
> > single patch file.
> >
> > Note: I am not fully sure how this is applicable to 'isal.ini and
> > isal.rst'. It will be good to have a check.
> >
> > Thanks
> > Vipin Varghese
> >
> > > -----Original Message-----
> > > From: dev <dev-bounces@dpdk.org> On Behalf Of Lee Daly
> > > Sent: Thursday, December 13, 2018 4:13 PM
> > > To: akhil.goyal@nxp.com
> > > Cc: dev@dpdk.org; Daly, Lee <lee.daly@intel.com>
> > > Subject: [dpdk-dev] [PATCH v3 3/3] doc: update ISA-L guide to
> > > reflect checksum support
> > >
> > > This updates the ISA-L compression driver guide on how to enable and
> > > use checksums.
> > >
> > > This also updates the compression drivers features matrix.
> > >
> > > V2:
> > > Documentation Changes
> > > V3:
> > > Added Release note
> > >
> > > Signed-off-by: Lee Daly <lee.daly@intel.com>
> > > Acked-by: Fiona Trahe <fiona.trahe@intel.com>
> > > ---
> > >  doc/guides/compressdevs/features/isal.ini |  2 ++
> > >  doc/guides/compressdevs/isal.rst          | 30
> > ++++++++++++++++++++++++++++-
> > > -
> > >  doc/guides/rel_notes/release_19_02.rst    |  5 +++++
> > >  3 files changed, 35 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/doc/guides/compressdevs/features/isal.ini
> > > b/doc/guides/compressdevs/features/isal.ini
> > > index 919cf70..e705031 100644
> > > --- a/doc/guides/compressdevs/features/isal.ini
> > > +++ b/doc/guides/compressdevs/features/isal.ini
> > > @@ -12,5 +12,7 @@ OOP SGL In SGL Out = Y  OOP SGL In LB  Out = Y
> > > OOP LB  In SGL Out = Y
> > >  Deflate            = Y
> > > +Adler32            = Y
> > > +Crc32              = Y
> > >  Fixed              = Y
> > >  Dynamic            = Y
> > > diff --git a/doc/guides/compressdevs/isal.rst
> > > b/doc/guides/compressdevs/isal.rst
> > > index 3bc3022..af1f41f 100644
> > > --- a/doc/guides/compressdevs/isal.rst
> > > +++ b/doc/guides/compressdevs/isal.rst
> > > @@ -27,6 +27,33 @@ Window size support:
> > >
> > >      * 32K
> > >
> > > +Checksum:
> > > +
> > > +    * CRC32
> > > +    * ADLER32
> > > +
> > > +To enable a checksum in the driver, the compression and/or
> > > +decompression xform structure, rte_comp_xform, must be filled with
> > > +either of the CompressDev checksum flags supported. ::
> > > +
> > > + compress_xform->compress.chksum = RTE_COMP_CHECKSUM_CRC32
> > > +
> > > + decompress_xform->decompress.chksum =
> > RTE_COMP_CHECKSUM_CRC32
> > > +
> > > +::
> > > +
> > > + compress_xform->compress.chksum =
> > RTE_COMP_CHECKSUM_ADLER32
> > > +
> > > + decompress_xform->decompress.chksum =
> > RTE_COMP_CHECKSUM_ADLER32
> > > +
> > > +If you request a checksum for compression or decompression, the
> > > +checksum field in the operation structure,  ``op->output_chksum``,
> > > +will be filled with the checksum.
> > > +
> > > +.. Note::
> > > +
> > > + For the compression case above, your output buffer will need to be
> > > + large
> > > enough to hold the compressed data plus a scratchpad for the
> > > checksum at the end, the scratchpad is 8 bytes for CRC32 and 4 bytes for
> Adler32.
> > > +
> > >  Level guide:
> > >
> > >  The ISA-L levels have been mapped to somewhat correspond to the
> > > same ZLIB level, @@ -75,13 +102,12 @@ As a result the level mappings
> > > from the API to the PMD are shown below.
> > >   The above table only shows mapping when API calls for dynamic
> > compression.
> > >   For fixed compression, regardless of API level, internally ISA-L
> > > level 0 is always used.
> > >
> > > +
> > >  Limitations
> > >  -----------
> > >
> > >  * Compressdev level 0, no compression, is not supported.
> > >
> > > -* Checksums will not be supported until future release.
> > > -
> > >  Installation
> > >  ------------
> > >
> > > diff --git a/doc/guides/rel_notes/release_19_02.rst
> > > b/doc/guides/rel_notes/release_19_02.rst
> > > index a94fa86..3a4d264 100644
> > > --- a/doc/guides/rel_notes/release_19_02.rst
> > > +++ b/doc/guides/rel_notes/release_19_02.rst
> > > @@ -54,6 +54,11 @@ New Features
> > >       Also, make sure to start the actual text at the margin.
> > >
> > =========================================================
> > >
> > > +   * **Enabled checksum support in the ISA-L compressdev driver.**
> > > +
> > > +     Added support for both adler and crc32 checksums in the ISA-L PMD.
> > > +     This aids data integrity across both compression and decompression.
> > > +
> > >
> > >  Removed Items
> > >  -------------
> > > --
> > > 2.7.4