* [dts] [PATCH]test_plans: add tx checksum case to rxtx_offload_test_plan.rst
@ 2019-05-10 5:00 Peng Yuan
2019-05-17 2:00 ` Tu, Lijuan
0 siblings, 1 reply; 2+ messages in thread
From: Peng Yuan @ 2019-05-10 5:00 UTC (permalink / raw)
To: dts; +Cc: Peng Yuan
Add tx checksum case to rxtx_offload_test_plan.rst
Signed-off-by: Peng Yuan <yuan.peng@intel.com>
diff --git a/test_plans/rxtx_offload_test_plan.rst b/test_plans/rxtx_offload_test_plan.rst
index 8b08682..246e1e1 100644
--- a/test_plans/rxtx_offload_test_plan.rst
+++ b/test_plans/rxtx_offload_test_plan.rst
@@ -193,6 +193,8 @@ Test case: Rx offload per-port setting in command-line
1. Enable rx cksum in command-line::
./testpmd -c f -n 4 -- -i --rxq=4 --txq=4 --enable-rx-cksum
+ testpmd> set fwd csum
+ testpmd> set verbose 1
testpmd> show port 0 rx_offload configuration
Rx Offloading Configuration of port 0 :
Port : IPV4_CKSUM UDP_CKSUM TCP_CKSUM
@@ -201,6 +203,20 @@ Test case: Rx offload per-port setting in command-line
Queue[ 2] :
Queue[ 3] :
+1) Send packets::
+
+ pkt1=Ether(dst="00:00:00:00:01:00", src="52:00:00:00:00:00")/IP(src="10.0.0.1")/TCP()/("X"*46)
+ pkt2=Ether(dst="00:00:00:00:01:00", src="52:00:00:00:00:00")/IP(chksum=0x0)/TCP(chksum=0xf)/("X"*46)
+ pkt3=Ether(dst="00:00:00:00:01:00", src="52:00:00:00:00:00")/IP(src="10.0.0.1")/UDP(chksum=0xf)/("X"*46)
+ pkt4=Ether(dst="00:00:00:00:01:00", src="52:00:00:00:00:00")/IP(chksum=0x0)/UDP()/("X"*46)
+
+2) Check the rx flags::
+
+ PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD
+ PKT_RX_L4_CKSUM_BAD PKT_RX_IP_CKSUM_BAD
+ PKT_RX_L4_CKSUM_BAD PKT_RX_IP_CKSUM_GOOD
+ PKT_RX_L4_CKSUM_UNKNOWN PKT_RX_IP_CKSUM_BAD
+
2. Disable the rx cksum per_port::
testpmd> port stop 0
@@ -504,6 +520,68 @@ Test case: Tx offload per-port setting in command-line
The tester port received packets with vlan ID.
The per_port capability can be enabled by per_port command.
+Test case: Tx offload checksum
+==============================
+
+1. Set checksum forward mode::
+
+ ./testpmd -c f -n 4 -- -i --rxq=4 --txq=4
+ testpmd> set fwd csum
+ testpmd> set verbose 1
+ testpmd> show port 0 tx_offload configuration
+ Rx Offloading Configuration of port 0 :
+ Port :
+ Queue[ 0] :
+ Queue[ 1] :
+ Queue[ 2] :
+ Queue[ 3] :
+
+1) Send an ipv4-udp packet to the port::
+
+ sendp([Ether(dst="00:00:00:00:01:00")/IP(src="100.0.0.1", dst="100.0.0.2")/UDP(sport=1024,dport=1025)], iface="enp131s0f3")
+
+2) Check the tx flags::
+
+ PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
+
+2. Enable the tx ipv4_cksum of port 1::
+
+ testpmd> port stop 1
+ testpmd> port config 1 tx_offload ipv4_cksum on
+ testpmd> show port 1 tx_offload configuration
+ Tx Offloading Configuration of port 1 :
+ Port : IPV4_CKSUM
+ Queue[ 0] : IPV4_CKSUM
+ Queue[ 1] : IPV4_CKSUM
+ Queue[ 2] : IPV4_CKSUM
+ Queue[ 3] : IPV4_CKSUM
+ testpmd> port start 1
+ testpmd> start
+
+ The port can start normally.
+
+3. Send an ipv4-udp packet to the port::
+
+ sendp([Ether(dst="00:00:00:00:01:00")/IP(src="100.0.0.1", dst="100.0.0.2")/UDP(sport=1024,dport=1025)], iface="enp131s0f3")
+
+ There is printing "PKT_TX_IP_CKSUM" and "PKT_TX_L4_NO_CKSUM" in the tx line.
+
+4. Disable tx ipv4_cksum and enable tx udp_cksum,
+ then send the same ipv4-udp packet, there is printing "PKT_TX_UDP_CKSUM",
+ but no "PKT_TX_IP_CKSUM".
+
+5. Try step 4 with "tcp_cksum" on, then send an ipv4-tcp packet::
+
+ sendp([Ether(dst="00:00:00:00:01:00")/IP(src="100.0.0.1", dst="100.0.0.2")/TCP(sport=1024,dport=1025)], iface="enp131s0f3")
+
+ There is printing "PKT_TX_TCP_CKSUM".
+
+6. Try step 4 with "sctp_cksum" on, then send an ipv4-sctp packet::
+
+ sendp([Ether(dst="00:00:00:00:01:00")/IP(src="100.0.0.1", dst="100.0.0.2")/sctp(sport=1024,dport=1025)], iface="enp131s0f3")
+
+ There is printing "PKT_TX_SCTP_CKSUM".
+
Test case: Tx offload per-queue and per-port setting
====================================================
--
2.14.3
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [dts] [PATCH]test_plans: add tx checksum case to rxtx_offload_test_plan.rst
2019-05-10 5:00 [dts] [PATCH]test_plans: add tx checksum case to rxtx_offload_test_plan.rst Peng Yuan
@ 2019-05-17 2:00 ` Tu, Lijuan
0 siblings, 0 replies; 2+ messages in thread
From: Tu, Lijuan @ 2019-05-17 2:00 UTC (permalink / raw)
To: Peng, Yuan, dts; +Cc: Peng, Yuan
Applied, thanks
> -----Original Message-----
> From: dts [mailto:dts-bounces@dpdk.org] On Behalf Of Peng Yuan
> Sent: Friday, May 10, 2019 1:00 PM
> To: dts@dpdk.org
> Cc: Peng, Yuan <yuan.peng@intel.com>
> Subject: [dts] [PATCH]test_plans: add tx checksum case to
> rxtx_offload_test_plan.rst
>
> Add tx checksum case to rxtx_offload_test_plan.rst
>
> Signed-off-by: Peng Yuan <yuan.peng@intel.com>
>
> diff --git a/test_plans/rxtx_offload_test_plan.rst
> b/test_plans/rxtx_offload_test_plan.rst
> index 8b08682..246e1e1 100644
> --- a/test_plans/rxtx_offload_test_plan.rst
> +++ b/test_plans/rxtx_offload_test_plan.rst
> @@ -193,6 +193,8 @@ Test case: Rx offload per-port setting in command-
> line 1. Enable rx cksum in command-line::
>
> ./testpmd -c f -n 4 -- -i --rxq=4 --txq=4 --enable-rx-cksum
> + testpmd> set fwd csum
> + testpmd> set verbose 1
> testpmd> show port 0 rx_offload configuration
> Rx Offloading Configuration of port 0 :
> Port : IPV4_CKSUM UDP_CKSUM TCP_CKSUM @@ -201,6 +203,20 @@
> Test case: Rx offload per-port setting in command-line
> Queue[ 2] :
> Queue[ 3] :
>
> +1) Send packets::
> +
> + pkt1=Ether(dst="00:00:00:00:01:00",
> src="52:00:00:00:00:00")/IP(src="10.0.0.1")/TCP()/("X"*46)
> + pkt2=Ether(dst="00:00:00:00:01:00",
> src="52:00:00:00:00:00")/IP(chksum=0x0)/TCP(chksum=0xf)/("X"*46)
> + pkt3=Ether(dst="00:00:00:00:01:00",
> src="52:00:00:00:00:00")/IP(src="10.0.0.1")/UDP(chksum=0xf)/("X"*46)
> + pkt4=Ether(dst="00:00:00:00:01:00",
> + src="52:00:00:00:00:00")/IP(chksum=0x0)/UDP()/("X"*46)
> +
> +2) Check the rx flags::
> +
> + PKT_RX_L4_CKSUM_GOOD PKT_RX_IP_CKSUM_GOOD
> + PKT_RX_L4_CKSUM_BAD PKT_RX_IP_CKSUM_BAD
> + PKT_RX_L4_CKSUM_BAD PKT_RX_IP_CKSUM_GOOD
> + PKT_RX_L4_CKSUM_UNKNOWN PKT_RX_IP_CKSUM_BAD
> +
> 2. Disable the rx cksum per_port::
>
> testpmd> port stop 0
> @@ -504,6 +520,68 @@ Test case: Tx offload per-port setting in command-
> line
> The tester port received packets with vlan ID.
> The per_port capability can be enabled by per_port command.
>
> +Test case: Tx offload checksum
> +==============================
> +
> +1. Set checksum forward mode::
> +
> + ./testpmd -c f -n 4 -- -i --rxq=4 --txq=4
> + testpmd> set fwd csum
> + testpmd> set verbose 1
> + testpmd> show port 0 tx_offload configuration
> + Rx Offloading Configuration of port 0 :
> + Port :
> + Queue[ 0] :
> + Queue[ 1] :
> + Queue[ 2] :
> + Queue[ 3] :
> +
> +1) Send an ipv4-udp packet to the port::
> +
> + sendp([Ether(dst="00:00:00:00:01:00")/IP(src="100.0.0.1",
> + dst="100.0.0.2")/UDP(sport=1024,dport=1025)], iface="enp131s0f3")
> +
> +2) Check the tx flags::
> +
> + PKT_TX_L4_NO_CKSUM PKT_TX_IPV4
> +
> +2. Enable the tx ipv4_cksum of port 1::
> +
> + testpmd> port stop 1
> + testpmd> port config 1 tx_offload ipv4_cksum on
> + testpmd> show port 1 tx_offload configuration
> + Tx Offloading Configuration of port 1 :
> + Port : IPV4_CKSUM
> + Queue[ 0] : IPV4_CKSUM
> + Queue[ 1] : IPV4_CKSUM
> + Queue[ 2] : IPV4_CKSUM
> + Queue[ 3] : IPV4_CKSUM
> + testpmd> port start 1
> + testpmd> start
> +
> + The port can start normally.
> +
> +3. Send an ipv4-udp packet to the port::
> +
> + sendp([Ether(dst="00:00:00:00:01:00")/IP(src="100.0.0.1",
> + dst="100.0.0.2")/UDP(sport=1024,dport=1025)], iface="enp131s0f3")
> +
> + There is printing "PKT_TX_IP_CKSUM" and "PKT_TX_L4_NO_CKSUM" in the
> tx line.
> +
> +4. Disable tx ipv4_cksum and enable tx udp_cksum,
> + then send the same ipv4-udp packet, there is printing
> "PKT_TX_UDP_CKSUM",
> + but no "PKT_TX_IP_CKSUM".
> +
> +5. Try step 4 with "tcp_cksum" on, then send an ipv4-tcp packet::
> +
> + sendp([Ether(dst="00:00:00:00:01:00")/IP(src="100.0.0.1",
> + dst="100.0.0.2")/TCP(sport=1024,dport=1025)], iface="enp131s0f3")
> +
> + There is printing "PKT_TX_TCP_CKSUM".
> +
> +6. Try step 4 with "sctp_cksum" on, then send an ipv4-sctp packet::
> +
> + sendp([Ether(dst="00:00:00:00:01:00")/IP(src="100.0.0.1",
> + dst="100.0.0.2")/sctp(sport=1024,dport=1025)], iface="enp131s0f3")
> +
> + There is printing "PKT_TX_SCTP_CKSUM".
> +
> Test case: Tx offload per-queue and per-port setting
> ====================================================
>
> --
> 2.14.3
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2019-05-17 2:00 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-10 5:00 [dts] [PATCH]test_plans: add tx checksum case to rxtx_offload_test_plan.rst Peng Yuan
2019-05-17 2:00 ` Tu, Lijuan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).