rte_flow_type_integrity example for checksum correctness

rte_flow_type_integrity example for checksum correctness

[Aisenur Yoldaş]

[-- Attachment #1: Type: text/plain, Size: 1091 bytes --]

Hi,
I am developing a project to read packets from pcap file and procces them to extract the corresponding payloads. In this project I want to offload the checksum calculations. Also I only want packages with correct checksums to reach the application layer . To do that I set port configuration like below:

struct rte_eth_conf port_conf = {
.rxmode = {
.mq_mode = RTE_ETH_MQ_RX_RSS,
.offloads =
RTE_ETH_TX_OFFLOAD_IPV4_CKSUM |
RTE_ETH_TX_OFFLOAD_UDP_CKSUM |
RTE_ETH_TX_OFFLOAD_TCP_CKSUM ,
},
.txmode = {
.mq_mode = RTE_ETH_MQ_TX_NONE,
.offloads =
RTE_ETH_TX_OFFLOAD_IPV4_CKSUM |
RTE_ETH_TX_OFFLOAD_UDP_CKSUM |
RTE_ETH_TX_OFFLOAD_TCP_CKSUM ,
},
.rx_adv_conf = {
.rss_conf = {
.rss_hf = RTE_ETH_RSS_IP |
RTE_ETH_RSS_TCP | RTE_ETH_RSS_UDP,
}
}
};
 
And for the correctness of checksums I want to use rte_flow pattern 

RTE_FLOW_ITEM_TYPE_INTEGRITY. But I could not find an example of it. Is there any example how to use this pattern
 
My card is Mellanox Technologies MT27710 Family [ConnectX-4 Lx] and I am using dpdk-23.03
 
Thanks,
Aisenur Yoldas



[-- Attachment #2.1: Type: text/html, Size: 1478 bytes --]

Re: rte_flow_type_integrity example for checksum correctness

[omer yamac]

[-- Attachment #1: Type: text/plain, Size: 351 bytes --]

Hi,
I just wonder why do you need a Mellanox? As I understood, you are reading
pcap file and you may check below link
https://doc.dpdk.org/guides/nics/pcap_ring.html


On Fri, Jun 9, 2023, 2:40 PM Gregory Etelson <getelson@nvidia.com> wrote:

> Hello Aisenur,
>
> Flow integrity support in MLX5 PMD starts with  ConnectX-6 Dx
>
> Regards,
> Gregory
>

[-- Attachment #2: Type: text/html, Size: 799 bytes --]

rte_flow_type_integrity example for checksum correctness

[Gregory Etelson]

Hello Aisenur,

Flow integrity support in MLX5 PMD starts with  ConnectX-6 Dx

Regards,
Gregory

rte_flow_type_integrity example for checksum correctness

[Aisenur Yoldaş]

[-- Attachment #1: Type: text/plain, Size: 1091 bytes --]

Hi,
I am developing a project to read packets from pcap file and procces them to extract the corresponding payloads. In this project I want to offload the checksum calculations. Also I only want packages with correct checksums to reach the application layer . To do that I set port configuration like below:

struct rte_eth_conf port_conf = {
.rxmode = {
.mq_mode = RTE_ETH_MQ_RX_RSS,
.offloads =
RTE_ETH_TX_OFFLOAD_IPV4_CKSUM |
RTE_ETH_TX_OFFLOAD_UDP_CKSUM |
RTE_ETH_TX_OFFLOAD_TCP_CKSUM ,
},
.txmode = {
.mq_mode = RTE_ETH_MQ_TX_NONE,
.offloads =
RTE_ETH_TX_OFFLOAD_IPV4_CKSUM |
RTE_ETH_TX_OFFLOAD_UDP_CKSUM |
RTE_ETH_TX_OFFLOAD_TCP_CKSUM ,
},
.rx_adv_conf = {
.rss_conf = {
.rss_hf = RTE_ETH_RSS_IP |
RTE_ETH_RSS_TCP | RTE_ETH_RSS_UDP,
}
}
};
 
And for the correctness of checksums I want to use rte_flow pattern 

RTE_FLOW_ITEM_TYPE_INTEGRITY. But I could not find an example of it. Is there any example how to use this pattern
 
My card is Mellanox Technologies MT27710 Family [ConnectX-4 Lx] and I am using dpdk-23.03
 
Thanks,
Aisenur Yoldas



[-- Attachment #2.1: Type: text/html, Size: 1478 bytes --]