DPDK patches and discussions
 help / color / mirror / Atom feed
From: Nalla Pradeep <pnalla@marvell.com>
To: Nalla Pradeep <pnalla@marvell.com>,
	Radha Mohan Chintakuntla <radhac@marvell.com>,
	Veerasenareddy Burru <vburru@marvell.com>
Cc: <jerinj@marvell.com>, <dev@dpdk.org>, <sburla@marvell.com>
Subject: [dpdk-dev] [PATCH v2 08/11] net/octeontx_ep: Setting up iq and oq registers
Date: Mon, 18 Jan 2021 09:35:59 +0000	[thread overview]
Message-ID: <20210118093602.5449-8-pnalla@marvell.com> (raw)
In-Reply-To: <20210118093602.5449-1-pnalla@marvell.com>

Configuring hardware registers with command queue(iq) and droq(oq)
parameters.

Signed-off-by: Nalla Pradeep <pnalla@marvell.com>
---
 drivers/net/octeontx_ep/otx2_ep_vf.c    | 124 ++++++++++++++++++++++++
 drivers/net/octeontx_ep/otx_ep_common.h |  65 +++++++++++++
 drivers/net/octeontx_ep/otx_ep_vf.c     | 124 ++++++++++++++++++++++++
 drivers/net/octeontx_ep/otx_ep_vf.h     |  53 ++++++++++
 4 files changed, 366 insertions(+)

diff --git a/drivers/net/octeontx_ep/otx2_ep_vf.c b/drivers/net/octeontx_ep/otx2_ep_vf.c
index e03d39f7dc..77850bcc7d 100644
--- a/drivers/net/octeontx_ep/otx2_ep_vf.c
+++ b/drivers/net/octeontx_ep/otx2_ep_vf.c
@@ -78,6 +78,127 @@ otx2_vf_setup_device_regs(struct otx_ep_device *otx_ep)
 	return 0;
 }
 
+static void
+otx2_vf_setup_iq_regs(struct otx_ep_device *otx_ep, uint32_t iq_no)
+{
+	struct otx_ep_instr_queue *iq = otx_ep->instr_queue[iq_no];
+	volatile uint64_t reg_val = 0ull;
+
+	reg_val = otx2_read64(otx_ep->hw_addr + SDP_VF_R_IN_CONTROL(iq_no));
+
+	/* Wait till IDLE to set to 1, not supposed to configure BADDR
+	 * as long as IDLE is 0
+	 */
+	if (!(reg_val & SDP_VF_R_IN_CTL_IDLE)) {
+		do {
+			reg_val = otx2_read64(otx_ep->hw_addr +
+					      SDP_VF_R_IN_CONTROL(iq_no));
+		} while (!(reg_val & SDP_VF_R_IN_CTL_IDLE));
+	}
+
+	/* Write the start of the input queue's ring and its size  */
+	otx2_write64(iq->base_addr_dma, otx_ep->hw_addr +
+		     SDP_VF_R_IN_INSTR_BADDR(iq_no));
+	otx2_write64(iq->nb_desc, otx_ep->hw_addr +
+		     SDP_VF_R_IN_INSTR_RSIZE(iq_no));
+
+	/* Remember the doorbell & instruction count register addr
+	 * for this queue
+	 */
+	iq->doorbell_reg = (uint8_t *)otx_ep->hw_addr +
+			   SDP_VF_R_IN_INSTR_DBELL(iq_no);
+	iq->inst_cnt_reg = (uint8_t *)otx_ep->hw_addr +
+			   SDP_VF_R_IN_CNTS(iq_no);
+
+	otx_ep_dbg("InstQ[%d]:dbell reg @ 0x%p instcnt_reg @ 0x%p",
+		   iq_no, iq->doorbell_reg, iq->inst_cnt_reg);
+
+	do {
+		reg_val = rte_read32(iq->inst_cnt_reg);
+		rte_write32(reg_val, iq->inst_cnt_reg);
+	} while (reg_val != 0);
+
+	/* IN INTR_THRESHOLD is set to max(FFFFFFFF) which disable the IN INTR
+	 * to raise
+	 */
+	otx2_write64(0x3FFFFFFFFFFFFFUL,
+		     otx_ep->hw_addr + SDP_VF_R_IN_INT_LEVELS(iq_no));
+}
+
+static void
+otx2_vf_setup_oq_regs(struct otx_ep_device *otx_ep, uint32_t oq_no)
+{
+	volatile uint64_t reg_val = 0ull;
+	uint64_t oq_ctl = 0ull;
+	struct otx_ep_droq *droq = otx_ep->droq[oq_no];
+
+	/* Wait on IDLE to set to 1, supposed to configure BADDR
+	 * as log as IDLE is 0
+	 */
+	reg_val = otx2_read64(otx_ep->hw_addr + SDP_VF_R_OUT_CONTROL(oq_no));
+
+	while (!(reg_val & SDP_VF_R_OUT_CTL_IDLE)) {
+		reg_val = otx2_read64(otx_ep->hw_addr +
+				      SDP_VF_R_OUT_CONTROL(oq_no));
+	}
+
+	otx2_write64(droq->desc_ring_dma, otx_ep->hw_addr +
+		     SDP_VF_R_OUT_SLIST_BADDR(oq_no));
+	otx2_write64(droq->nb_desc, otx_ep->hw_addr +
+		     SDP_VF_R_OUT_SLIST_RSIZE(oq_no));
+
+	oq_ctl = otx2_read64(otx_ep->hw_addr + SDP_VF_R_OUT_CONTROL(oq_no));
+
+	/* Clear the ISIZE and BSIZE (22-0) */
+	oq_ctl &= ~(0x7fffffull);
+
+	/* Populate the BSIZE (15-0) */
+	oq_ctl |= (droq->buffer_size & 0xffff);
+
+#ifndef BUFPTR_ONLY_MODE
+	/* Populate ISIZE(22-16) */
+	oq_ctl |= ((OTX_EP_RH_SIZE << 16) & 0x7fffff);
+#endif
+	otx2_write64(oq_ctl, otx_ep->hw_addr + SDP_VF_R_OUT_CONTROL(oq_no));
+
+	/* Mapped address of the pkt_sent and pkts_credit regs */
+	droq->pkts_sent_reg = (uint8_t *)otx_ep->hw_addr +
+			      SDP_VF_R_OUT_CNTS(oq_no);
+	droq->pkts_credit_reg = (uint8_t *)otx_ep->hw_addr +
+				SDP_VF_R_OUT_SLIST_DBELL(oq_no);
+
+	rte_write64(0x3FFFFFFFFFFFFFUL,
+		    otx_ep->hw_addr + SDP_VF_R_OUT_INT_LEVELS(oq_no));
+
+	/* Clear PKT_CNT register */
+	rte_write64(0xFFFFFFFFF, (uint8_t *)otx_ep->hw_addr +
+		    SDP_VF_R_OUT_PKT_CNT(oq_no));
+
+	/* Clear the OQ doorbell  */
+	rte_write32(0xFFFFFFFF, droq->pkts_credit_reg);
+	while ((rte_read32(droq->pkts_credit_reg) != 0ull)) {
+		rte_write32(0xFFFFFFFF, droq->pkts_credit_reg);
+		rte_delay_ms(1);
+	}
+	otx_ep_dbg("SDP_R[%d]_credit:%x", oq_no,
+		   rte_read32(droq->pkts_credit_reg));
+
+	/* Clear the OQ_OUT_CNTS doorbell  */
+	reg_val = rte_read32(droq->pkts_sent_reg);
+	rte_write32((uint32_t)reg_val, droq->pkts_sent_reg);
+
+	otx_ep_dbg("SDP_R[%d]_sent: %x", oq_no,
+		   rte_read32(droq->pkts_sent_reg));
+
+	while (((rte_read32(droq->pkts_sent_reg)) != 0ull)) {
+		reg_val = rte_read32(droq->pkts_sent_reg);
+		rte_write32((uint32_t)reg_val, droq->pkts_sent_reg);
+		rte_delay_ms(1);
+	}
+	otx_ep_dbg("SDP_R[%d]_sent: %x", oq_no,
+		   rte_read32(droq->pkts_sent_reg));
+}
+
 static const struct otx_ep_config default_otx2_ep_conf = {
 	/* IQ attributes */
 	.iq                        = {
@@ -132,6 +253,9 @@ otx2_ep_vf_setup_device(struct otx_ep_device *otx_ep)
 
 	otx2_info("SDP RPVF: %d", otx_ep->sriov_info.rings_per_vf);
 
+	otx_ep->fn_list.setup_iq_regs       = otx2_vf_setup_iq_regs;
+	otx_ep->fn_list.setup_oq_regs       = otx2_vf_setup_oq_regs;
+
 	otx_ep->fn_list.setup_device_regs   = otx2_vf_setup_device_regs;
 
 	return 0;
diff --git a/drivers/net/octeontx_ep/otx_ep_common.h b/drivers/net/octeontx_ep/otx_ep_common.h
index 661e8e4c55..966e87a417 100644
--- a/drivers/net/octeontx_ep/otx_ep_common.h
+++ b/drivers/net/octeontx_ep/otx_ep_common.h
@@ -33,6 +33,33 @@
 #define otx_ep_dbg(fmt, args...)				\
 	otx_ep_printf(DEBUG, fmt, ##args)
 
+/* Input Request Header format */
+union otx_ep_instr_irh {
+	uint64_t u64;
+	struct {
+		/* Request ID  */
+		uint64_t rid:16;
+
+		/* PCIe port to use for response */
+		uint64_t pcie_port:3;
+
+		/* Scatter indicator  1=scatter */
+		uint64_t scatter:1;
+
+		/* Size of Expected result OR no. of entries in scatter list */
+		uint64_t rlenssz:14;
+
+		/* Desired destination port for result */
+		uint64_t dport:6;
+
+		/* Opcode Specific parameters */
+		uint64_t param:8;
+
+		/* Opcode for the return packet  */
+		uint64_t opcode:16;
+	} s;
+};
+
 #define otx_ep_write64(value, base_addr, reg_off) \
 	{\
 	typeof(value) val = (value); \
@@ -42,6 +69,33 @@
 	rte_write64(val, ((base_addr) + off)); \
 	}
 
+/* Instruction Header - for OCTEON-TX models */
+typedef union otx_ep_instr_ih {
+	uint64_t u64;
+	struct {
+	  /** Data Len */
+		uint64_t tlen:16;
+
+	  /** Reserved */
+		uint64_t rsvd:20;
+
+	  /** PKIND for OTX_EP */
+		uint64_t pkind:6;
+
+	  /** Front Data size */
+		uint64_t fsz:6;
+
+	  /** No. of entries in gather list */
+		uint64_t gsz:14;
+
+	  /** Gather indicator 1=gather*/
+		uint64_t gather:1;
+
+	  /** Reserved3 */
+		uint64_t reserved3:1;
+	} s;
+} otx_ep_instr_ih_t;
+
 /* OTX_EP IQ request list */
 struct otx_ep_instr_list {
 	void *buf;
@@ -244,6 +298,16 @@ struct otx_ep_droq {
 	/* The size of each buffer pointed by the buffer pointer. */
 	uint32_t buffer_size;
 
+	/** Pointer to the mapped packet credit register.
+	 *  Host writes number of info/buffer ptrs available to this register
+	 */
+	void *pkts_credit_reg;
+
+	/** Pointer to the mapped packet sent register. OCTEON TX2 writes the
+	 *  number of packets DMA'ed to host memory in this register.
+	 */
+	void *pkts_sent_reg;
+
 	/* Statistics for this DROQ. */
 	struct otx_ep_droq_stats stats;
 
@@ -259,6 +323,7 @@ struct otx_ep_droq {
 	/* Allocated size of info list. */
 	uint32_t info_alloc_size;
 
+
 	/* Memory zone **/
 	const struct rte_memzone *desc_ring_mz;
 	const struct rte_memzone *info_mz;
diff --git a/drivers/net/octeontx_ep/otx_ep_vf.c b/drivers/net/octeontx_ep/otx_ep_vf.c
index 7fad313982..076f8fe71e 100644
--- a/drivers/net/octeontx_ep/otx_ep_vf.c
+++ b/drivers/net/octeontx_ep/otx_ep_vf.c
@@ -91,6 +91,127 @@ otx_ep_setup_device_regs(struct otx_ep_device *otx_ep)
 	return 0;
 }
 
+static void
+otx_ep_setup_iq_regs(struct otx_ep_device *otx_ep, uint32_t iq_no)
+{
+	struct otx_ep_instr_queue *iq = otx_ep->instr_queue[iq_no];
+	volatile uint64_t reg_val = 0ull;
+
+	reg_val = rte_read64(otx_ep->hw_addr + OTX_EP_R_IN_CONTROL(iq_no));
+
+	/* Wait till IDLE to set to 1, not supposed to configure BADDR
+	 * as long as IDLE is 0
+	 */
+	if (!(reg_val & OTX_EP_R_IN_CTL_IDLE)) {
+		do {
+			reg_val = rte_read64(otx_ep->hw_addr +
+					      OTX_EP_R_IN_CONTROL(iq_no));
+		} while (!(reg_val & OTX_EP_R_IN_CTL_IDLE));
+	}
+
+	/* Write the start of the input queue's ring and its size  */
+	otx_ep_write64(iq->base_addr_dma, otx_ep->hw_addr,
+		       OTX_EP_R_IN_INSTR_BADDR(iq_no));
+	otx_ep_write64(iq->nb_desc, otx_ep->hw_addr,
+		       OTX_EP_R_IN_INSTR_RSIZE(iq_no));
+
+	/* Remember the doorbell & instruction count register addr
+	 * for this queue
+	 */
+	iq->doorbell_reg = (uint8_t *)otx_ep->hw_addr +
+			   OTX_EP_R_IN_INSTR_DBELL(iq_no);
+	iq->inst_cnt_reg = (uint8_t *)otx_ep->hw_addr +
+			   OTX_EP_R_IN_CNTS(iq_no);
+
+	otx_ep_dbg("InstQ[%d]:dbell reg @ 0x%p instcnt_reg @ 0x%p\n",
+		     iq_no, iq->doorbell_reg, iq->inst_cnt_reg);
+
+	do {
+		reg_val = rte_read32(iq->inst_cnt_reg);
+		rte_write32(reg_val, iq->inst_cnt_reg);
+	} while (reg_val !=  0);
+
+	/* IN INTR_THRESHOLD is set to max(FFFFFFFF) which disable the IN INTR
+	 * to raise
+	 */
+	/* reg_val = rte_read64(otx_ep->hw_addr +
+	 * OTX_EP_R_IN_INT_LEVELS(iq_no));
+	 */
+	reg_val = 0xffffffff;
+
+	otx_ep_write64(reg_val, otx_ep->hw_addr, OTX_EP_R_IN_INT_LEVELS(iq_no));
+}
+
+static void
+otx_ep_setup_oq_regs(struct otx_ep_device *otx_ep, uint32_t oq_no)
+{
+	volatile uint64_t reg_val = 0ull;
+	uint64_t oq_ctl = 0ull;
+
+	struct otx_ep_droq *droq = otx_ep->droq[oq_no];
+
+	/* Wait on IDLE to set to 1, supposed to configure BADDR
+	 * as log as IDLE is 0
+	 */
+	otx_ep_write64(0ULL, otx_ep->hw_addr, OTX_EP_R_OUT_ENABLE(oq_no));
+
+	reg_val = rte_read64(otx_ep->hw_addr + OTX_EP_R_OUT_CONTROL(oq_no));
+
+	while (!(reg_val & OTX_EP_R_OUT_CTL_IDLE)) {
+		reg_val = rte_read64(otx_ep->hw_addr +
+				      OTX_EP_R_OUT_CONTROL(oq_no));
+	}
+
+	otx_ep_write64(droq->desc_ring_dma, otx_ep->hw_addr,
+		       OTX_EP_R_OUT_SLIST_BADDR(oq_no));
+	otx_ep_write64(droq->nb_desc, otx_ep->hw_addr,
+		       OTX_EP_R_OUT_SLIST_RSIZE(oq_no));
+
+	oq_ctl = rte_read64(otx_ep->hw_addr + OTX_EP_R_OUT_CONTROL(oq_no));
+
+	/* Clear the ISIZE and BSIZE (22-0) */
+	oq_ctl &= ~(0x7fffffull);
+
+	/* Populate the BSIZE (15-0) */
+	oq_ctl |= (droq->buffer_size & 0xffff);
+
+#ifndef BUFPTR_ONLY_MODE
+	oq_ctl |= ((OTX_EP_RH_SIZE << 16) & 0x7fffff);/*populate ISIZE(22-16)*/
+#endif
+	otx_ep_write64(oq_ctl, otx_ep->hw_addr, OTX_EP_R_OUT_CONTROL(oq_no));
+
+	/* Mapped address of the pkt_sent and pkts_credit regs */
+	droq->pkts_sent_reg = (uint8_t *)otx_ep->hw_addr +
+			      OTX_EP_R_OUT_CNTS(oq_no);
+	droq->pkts_credit_reg = (uint8_t *)otx_ep->hw_addr +
+				OTX_EP_R_OUT_SLIST_DBELL(oq_no);
+
+	otx_ep_write64(0x3fffffffffffffULL, otx_ep->hw_addr,
+		       OTX_EP_R_OUT_INT_LEVELS(oq_no));
+
+	/* Clear the OQ doorbell  */
+	rte_write32(0xFFFFFFFF, droq->pkts_credit_reg);
+	while ((rte_read32(droq->pkts_credit_reg) != 0ull)) {
+		rte_write32(0xFFFFFFFF, droq->pkts_credit_reg);
+		rte_delay_ms(1);
+	}
+	otx_ep_dbg("OTX_EP_R[%d]_credit:%x\n", oq_no,
+		     rte_read32(droq->pkts_credit_reg));
+
+	/* Clear the OQ_OUT_CNTS doorbell  */
+	reg_val = rte_read32(droq->pkts_sent_reg);
+	rte_write32((uint32_t)reg_val, droq->pkts_sent_reg);
+
+	otx_ep_dbg("OTX_EP_R[%d]_sent: %x\n", oq_no,
+		     rte_read32(droq->pkts_sent_reg));
+
+	while (((rte_read32(droq->pkts_sent_reg)) != 0ull)) {
+		reg_val = rte_read32(droq->pkts_sent_reg);
+		rte_write32((uint32_t)reg_val, droq->pkts_sent_reg);
+		rte_delay_ms(1);
+	}
+}
+
 /* OTX_EP default configuration */
 static const struct otx_ep_config default_otx_ep_conf = {
 	/* IQ attributes */
@@ -148,6 +269,9 @@ otx_ep_vf_setup_device(struct otx_ep_device *otx_ep)
 
 	otx_ep_info("OTX_EP RPVF: %d\n", otx_ep->sriov_info.rings_per_vf);
 
+	otx_ep->fn_list.setup_iq_regs       = otx_ep_setup_iq_regs;
+	otx_ep->fn_list.setup_oq_regs       = otx_ep_setup_oq_regs;
+
 	otx_ep->fn_list.setup_device_regs   = otx_ep_setup_device_regs;
 
 	return 0;
diff --git a/drivers/net/octeontx_ep/otx_ep_vf.h b/drivers/net/octeontx_ep/otx_ep_vf.h
index 42bb04f14f..50a61352a2 100644
--- a/drivers/net/octeontx_ep/otx_ep_vf.h
+++ b/drivers/net/octeontx_ep/otx_ep_vf.h
@@ -4,13 +4,38 @@
 #ifndef _OTX_EP_VF_H_
 #define _OTX_EP_VF_H_
 
+
+
+
+
 #define OTX_EP_RING_OFFSET                (0x1ull << 17)
 
 /* OTX_EP VF IQ Registers */
 #define OTX_EP_R_IN_CONTROL_START         (0x10000)
+#define OTX_EP_R_IN_INSTR_BADDR_START     (0x10020)
+#define OTX_EP_R_IN_INSTR_RSIZE_START     (0x10030)
+#define OTX_EP_R_IN_INSTR_DBELL_START     (0x10040)
+#define OTX_EP_R_IN_CNTS_START            (0x10050)
+#define OTX_EP_R_IN_INT_LEVELS_START      (0x10060)
+
 #define OTX_EP_R_IN_CONTROL(ring)  \
 	(OTX_EP_R_IN_CONTROL_START + ((ring) * OTX_EP_RING_OFFSET))
 
+#define OTX_EP_R_IN_INSTR_BADDR(ring)   \
+	(OTX_EP_R_IN_INSTR_BADDR_START + ((ring) * OTX_EP_RING_OFFSET))
+
+#define OTX_EP_R_IN_INSTR_RSIZE(ring)   \
+	(OTX_EP_R_IN_INSTR_RSIZE_START + ((ring) * OTX_EP_RING_OFFSET))
+
+#define OTX_EP_R_IN_INSTR_DBELL(ring)   \
+	(OTX_EP_R_IN_INSTR_DBELL_START + ((ring) * OTX_EP_RING_OFFSET))
+
+#define OTX_EP_R_IN_CNTS(ring)          \
+	(OTX_EP_R_IN_CNTS_START + ((ring) * OTX_EP_RING_OFFSET))
+
+#define OTX_EP_R_IN_INT_LEVELS(ring)    \
+	(OTX_EP_R_IN_INT_LEVELS_START + ((ring) * OTX_EP_RING_OFFSET))
+
 /* OTX_EP VF IQ Masks */
 #define OTX_EP_R_IN_CTL_RPVF_MASK       (0xF)
 #define	OTX_EP_R_IN_CTL_RPVF_POS        (48)
@@ -20,10 +45,38 @@
 #define OTX_EP_R_IN_CTL_IS_64B          (0x1ull << 24)
 #define OTX_EP_R_IN_CTL_ESR             (0x1ull << 1)
 /* OTX_EP VF OQ Registers */
+#define OTX_EP_R_OUT_CNTS_START              (0x10100)
+#define OTX_EP_R_OUT_INT_LEVELS_START        (0x10110)
+#define OTX_EP_R_OUT_SLIST_BADDR_START       (0x10120)
+#define OTX_EP_R_OUT_SLIST_RSIZE_START       (0x10130)
+#define OTX_EP_R_OUT_SLIST_DBELL_START       (0x10140)
 #define OTX_EP_R_OUT_CONTROL_START           (0x10150)
+#define OTX_EP_R_OUT_ENABLE_START            (0x10160)
+
 #define OTX_EP_R_OUT_CONTROL(ring)    \
 	(OTX_EP_R_OUT_CONTROL_START + ((ring) * OTX_EP_RING_OFFSET))
+
+#define OTX_EP_R_OUT_ENABLE(ring)     \
+	(OTX_EP_R_OUT_ENABLE_START + ((ring) * OTX_EP_RING_OFFSET))
+
+#define OTX_EP_R_OUT_SLIST_BADDR(ring)  \
+	(OTX_EP_R_OUT_SLIST_BADDR_START + ((ring) * OTX_EP_RING_OFFSET))
+
+#define OTX_EP_R_OUT_SLIST_RSIZE(ring)  \
+	(OTX_EP_R_OUT_SLIST_RSIZE_START + ((ring) * OTX_EP_RING_OFFSET))
+
+#define OTX_EP_R_OUT_SLIST_DBELL(ring)  \
+	(OTX_EP_R_OUT_SLIST_DBELL_START + ((ring) * OTX_EP_RING_OFFSET))
+
+#define OTX_EP_R_OUT_CNTS(ring)   \
+	(OTX_EP_R_OUT_CNTS_START + ((ring) * OTX_EP_RING_OFFSET))
+
+#define OTX_EP_R_OUT_INT_LEVELS(ring)   \
+	(OTX_EP_R_OUT_INT_LEVELS_START + ((ring) * OTX_EP_RING_OFFSET))
+
 /* OTX_EP VF OQ Masks */
+
+#define OTX_EP_R_OUT_CTL_IDLE         (1ull << 36)
 #define OTX_EP_R_OUT_CTL_ES_I         (1ull << 34)
 #define OTX_EP_R_OUT_CTL_NSR_I        (1ull << 33)
 #define OTX_EP_R_OUT_CTL_ROR_I        (1ull << 32)
-- 
2.17.1


  parent reply	other threads:[~2021-01-18  9:37 UTC|newest]

Thread overview: 76+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-01-18  9:35 [dpdk-dev] [PATCH v2 01/11] net/octeontx_ep: add build and doc infrastructure Nalla Pradeep
2021-01-18  9:35 ` [dpdk-dev] [PATCH v2 02/11] net/octeontx_ep: add ethdev probe and remove Nalla Pradeep
2021-01-19 11:55   ` Jerin Jacob
2021-01-26 15:27   ` Ferruh Yigit
2021-01-27 11:45     ` [dpdk-dev] [EXT] " Pradeep Kumar Nalla
2021-01-18  9:35 ` [dpdk-dev] [PATCH v2 03/11] net/octeontx_ep: add device init and uninit Nalla Pradeep
2021-01-19 12:06   ` Jerin Jacob
2021-01-26 15:25   ` Ferruh Yigit
2021-01-18  9:35 ` [dpdk-dev] [PATCH v2 04/11] net/octeontx_ep: Added basic device setup Nalla Pradeep
2021-01-19 12:09   ` Jerin Jacob
2021-01-26 15:29   ` Ferruh Yigit
2021-01-18  9:35 ` [dpdk-dev] [PATCH v2 05/11] net/octeontx_ep: Add dev info get and configure Nalla Pradeep
2021-01-26 15:31   ` Ferruh Yigit
2021-01-28  7:03     ` [dpdk-dev] [EXT] " Pradeep Kumar Nalla
2021-01-18  9:35 ` [dpdk-dev] [PATCH v2 06/11] net/octeontx_ep: Added rxq setup and release Nalla Pradeep
2021-01-18  9:35 ` [dpdk-dev] [PATCH v2 07/11] net/octeontx_ep: Added tx queue " Nalla Pradeep
2021-01-18  9:35 ` Nalla Pradeep [this message]
2021-01-26 15:32   ` [dpdk-dev] [PATCH v2 08/11] net/octeontx_ep: Setting up iq and oq registers Ferruh Yigit
2021-01-18  9:36 ` [dpdk-dev] [PATCH v2 09/11] net/octeontx_ep: Added dev start and stop Nalla Pradeep
2021-01-26 15:32   ` Ferruh Yigit
2021-01-18  9:36 ` [dpdk-dev] [PATCH v2 10/11] net/octeontx_ep: Receive data path function added Nalla Pradeep
2021-01-26 15:33   ` Ferruh Yigit
2021-01-18  9:36 ` [dpdk-dev] [PATCH v2 11/11] net/octeontx_ep: Transmit " Nalla Pradeep
2021-01-26 15:35   ` Ferruh Yigit
2021-01-19 11:50 ` [dpdk-dev] [PATCH v2 01/11] net/octeontx_ep: add build and doc infrastructure Jerin Jacob
2021-01-26 15:09 ` Ferruh Yigit
2021-01-26 15:41 ` Ferruh Yigit
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 00/11] Octeon Tx/Tx2 Endpoint pmd Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 00/12] " Nalla Pradeep
2021-01-29 12:44     ` [dpdk-dev] [PATCH v7 " Nalla Pradeep
2021-01-29 14:08       ` Ferruh Yigit
2021-01-29 12:44     ` [dpdk-dev] [PATCH v7 01/12] raw/octeontx_ep: changed device id Nalla Pradeep
2021-02-11  0:58       ` Radha Mohan
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 02/12] net/octeontx_ep: add build and doc infrastructure Nalla Pradeep
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 03/12] net/octeontx_ep: add ethdev probe and remove Nalla Pradeep
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 04/12] net/octeontx_ep: add device init and uninit Nalla Pradeep
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 05/12] net/octeontx_ep: added basic device setup Nalla Pradeep
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 06/12] net/octeontx_ep: add dev info get and configure Nalla Pradeep
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 07/12] net/octeontx_ep: added rxq setup and release Nalla Pradeep
2021-01-29 14:04       ` Ferruh Yigit
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 08/12] net/octeontx_ep: added tx queue " Nalla Pradeep
2021-01-29 14:04       ` Ferruh Yigit
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 09/12] net/octeontx_ep: setting up iq and oq registers Nalla Pradeep
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 10/12] net/octeontx_ep: added dev start and stop Nalla Pradeep
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 11/12] net/octeontx_ep: receive data path function added Nalla Pradeep
2021-01-29 12:45     ` [dpdk-dev] [PATCH v7 12/12] net/octeontx_ep: transmit " Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 01/12] raw/octeontx_ep: changed device id Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 02/12] net/octeontx_ep: add build and doc infrastructure Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 03/12] net/octeontx_ep: add ethdev probe and remove Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 04/12] net/octeontx_ep: add device init and uninit Nalla Pradeep
2021-01-29  9:19     ` Ferruh Yigit
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 05/12] net/octeontx_ep: added basic device setup Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 06/12] net/octeontx_ep: add dev info get and configure Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 07/12] net/octeontx_ep: added rxq setup and release Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 08/12] net/octeontx_ep: added tx queue " Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 09/12] net/octeontx_ep: setting up iq and oq registers Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 10/12] net/octeontx_ep: added dev start and stop Nalla Pradeep
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 11/12] net/octeontx_ep: receive data path function added Nalla Pradeep
2021-01-29  9:24     ` Ferruh Yigit
2021-01-29  0:16   ` [dpdk-dev] [PATCH v6 12/12] net/octeontx_ep: transmit " Nalla Pradeep
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 01/11] net/octeontx_ep: add build and doc infrastructure Nalla Pradeep
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 02/11] net/octeontx_ep: add ethdev probe and remove Nalla Pradeep
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 03/11] net/octeontx_ep: add device init and uninit Nalla Pradeep
2021-01-28 16:55   ` Ferruh Yigit
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 04/11] net/octeontx_ep: added basic device setup Nalla Pradeep
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 05/11] net/octeontx_ep: add dev info get and configure Nalla Pradeep
2021-01-28 16:56   ` Ferruh Yigit
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 06/11] net/octeontx_ep: added rxq setup and release Nalla Pradeep
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 07/11] net/octeontx_ep: added tx queue " Nalla Pradeep
2021-01-28 16:57   ` Ferruh Yigit
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 08/11] net/octeontx_ep: setting up iq and oq registers Nalla Pradeep
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 09/11] net/octeontx_ep: added dev start and stop Nalla Pradeep
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 10/11] net/octeontx_ep: receive data path function added Nalla Pradeep
2021-01-28 16:58   ` Ferruh Yigit
2021-01-28 15:22 ` [dpdk-dev] [PATCH v5 11/11] net/octeontx_ep: transmit " Nalla Pradeep
2021-01-28 16:59   ` Ferruh Yigit

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210118093602.5449-8-pnalla@marvell.com \
    --to=pnalla@marvell.com \
    --cc=dev@dpdk.org \
    --cc=jerinj@marvell.com \
    --cc=radhac@marvell.com \
    --cc=sburla@marvell.com \
    --cc=vburru@marvell.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).