From: "Dai, Wei" <wei.dai@intel.com>
To: Olivier Matz <olivier.matz@6wind.com>,
"dev@dpdk.org" <dev@dpdk.org>,
"Zhang, Helin" <helin.zhang@intel.com>,
"Ananyev, Konstantin" <konstantin.ananyev@intel.com>
Cc: "laurent.hardy@6wind.com" <laurent.hardy@6wind.com>
Subject: Re: [dpdk-dev] [PATCH v2] net/ixgbe: ensure link status is updated
Date: Thu, 30 Mar 2017 16:32:47 +0000 [thread overview]
Message-ID: <49759EB36A64CF4892C1AFEC9231E8D650A23CB0@PGSMSX101.gar.corp.intel.com> (raw)
In-Reply-To: <20170330111959.43ac9078@platinum>
Hi, Olivier
Has anyone already tested this patch ?
Can you present some useful info on how to test it ?
Can I use ethtool with some argument to downgrade or upgrade the rate of peer port ?
I have just run testpmd with 82599, the hw->phy. autoneg_advertised is 0 after rte_eal_init() and rte_eth_dev_start().
So I think the codes in if (!speed) { ... } is likely to be run.
I agree with most of your codes.
But why to limit speed of NIC to 10Gbps if autoneg is false and 10Gbps is supported ?
In this case, how about setting multiple speed ?
Thanks
-Wei
> -----Original Message-----
> From: Olivier Matz [mailto:olivier.matz@6wind.com]
> Sent: Thursday, March 30, 2017 5:20 PM
> To: dev@dpdk.org; Zhang, Helin <helin.zhang@intel.com>; Ananyev,
> Konstantin <konstantin.ananyev@intel.com>; Dai, Wei <wei.dai@intel.com>
> Cc: laurent.hardy@6wind.com
> Subject: Re: [dpdk-dev] [PATCH v2] net/ixgbe: ensure link status is updated
>
> Hi,
>
> Can this patch be applied?
>
> Thanks,
> Olivier
>
>
> On Thu, 16 Feb 2017 17:32:01 +0100, Olivier Matz <olivier.matz@6wind.com>
> wrote:
> > From: Laurent Hardy <laurent.hardy@6wind.com>
> >
> > In case of fiber and link speed set to 1Gb at peer side (with autoneg
> > or with defined speed), link status could be not properly updated at
> > time cable is plugged-in.
> > Indeed if cable was not plugged when device has been configured and
> > started then link status will not be updated properly with new speed
> > as no link setup will be triggered.
> >
> > To avoid this issue, IXGBE_FLAG_NEED_LINK_CONFIG is set to try a link
> > setup each time link_update() is triggered and current link status is
> > down. When cable is plugged-in, link setup will be performed via
> > ixgbe_setup_link().
> >
> > Signed-off-by: Laurent Hardy <laurent.hardy@6wind.com>
> > ---
> >
> > v1 -> v2:
> > - rebase on top of head (change flag to 1<<4)
> > - fix regression with copper links: only update link for fiber links
> >
> > drivers/net/ixgbe/ixgbe_ethdev.c | 21 +++++++++++++++++++++
> > drivers/net/ixgbe/ixgbe_ethdev.h | 1 +
> > 2 files changed, 22 insertions(+)
> >
> > diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> > b/drivers/net/ixgbe/ixgbe_ethdev.c
> > index 0b89598..1114106 100644
> > --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> > +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> > @@ -2357,6 +2357,7 @@ ixgbe_dev_configure(struct rte_eth_dev *dev)
> >
> > /* set flag to update link status after init */
> > intr->flags |= IXGBE_FLAG_NEED_LINK_UPDATE;
> > + intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
> >
> > /*
> > * Initialize to TRUE. If any of Rx queues doesn't meet the bulk @@
> > -3515,8 +3516,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int
> wait_to_complete)
> > struct ixgbe_hw *hw =
> IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
> > struct rte_eth_link link, old;
> > ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
> > + struct ixgbe_interrupt *intr =
> > + IXGBE_DEV_PRIVATE_TO_INTR(dev->data->dev_private);
> > int link_up;
> > int diag;
> > + u32 speed = 0;
> > + bool autoneg = false;
> >
> > link.link_status = ETH_LINK_DOWN;
> > link.link_speed = 0;
> > @@ -3526,6 +3531,20 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev,
> > int wait_to_complete)
> >
> > hw->mac.get_link_status = true;
> >
> > + if ((intr->flags & IXGBE_FLAG_NEED_LINK_CONFIG) &&
> > + hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) {
> > + speed = hw->phy.autoneg_advertised;
> > + if (!speed) {
> > + ixgbe_get_link_capabilities(hw, &speed, &autoneg);
> > + /* setup the highest link when no autoneg */
> > + if (!autoneg) {
> > + if (speed & IXGBE_LINK_SPEED_10GB_FULL)
> > + speed = IXGBE_LINK_SPEED_10GB_FULL;
> > + }
> > + }
> > + ixgbe_setup_link(hw, speed, true);
> > + }
> > +
> > /* check if it needs to wait to complete, if lsc interrupt is enabled */
> > if (wait_to_complete == 0 || dev->data->dev_conf.intr_conf.lsc != 0)
> > diag = ixgbe_check_link(hw, &link_speed, &link_up, 0); @@ -3543,10
> > +3562,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int
> > wait_to_complete)
> >
> > if (link_up == 0) {
> > rte_ixgbe_dev_atomic_write_link_status(dev, &link);
> > + intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
> > if (link.link_status == old.link_status)
> > return -1;
> > return 0;
> > }
> > + intr->flags &= ~IXGBE_FLAG_NEED_LINK_CONFIG;
> > link.link_status = ETH_LINK_UP;
> > link.link_duplex = ETH_LINK_FULL_DUPLEX;
> >
> > diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h
> > b/drivers/net/ixgbe/ixgbe_ethdev.h
> > index aabbb00..bed4379 100644
> > --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> > +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> > @@ -45,6 +45,7 @@
> > #define IXGBE_FLAG_MAILBOX (uint32_t)(1 << 1)
> > #define IXGBE_FLAG_PHY_INTERRUPT (uint32_t)(1 << 2)
> > #define IXGBE_FLAG_MACSEC (uint32_t)(1 << 3)
> > +#define IXGBE_FLAG_NEED_LINK_CONFIG (uint32_t)(1 << 4)
> >
> > /*
> > * Defines that were not part of ixgbe_type.h as they are not used by
> > the
next prev parent reply other threads:[~2017-03-30 16:32 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-17 17:29 [dpdk-dev] [PATCH] " Laurent Hardy
2016-11-28 17:27 ` Laurent Hardy
2016-12-08 17:10 ` Ferruh Yigit
2017-02-01 14:14 ` Thomas Monjalon
2017-02-08 15:51 ` Dai, Wei
2017-02-08 17:03 ` Olivier MATZ
2017-02-13 3:17 ` Dai, Wei
2017-02-16 16:32 ` [dpdk-dev] [PATCH v2] " Olivier Matz
2017-03-30 9:19 ` Olivier Matz
2017-03-30 16:32 ` Dai, Wei [this message]
2017-04-03 13:23 ` Laurent Hardy
2017-04-10 13:36 ` Ferruh Yigit
2017-04-11 12:13 ` Laurent Hardy
2017-04-12 8:21 ` [dpdk-dev] [PATCH] " Laurent Hardy
2017-04-18 14:33 ` Dai, Wei
2017-04-27 15:03 ` [dpdk-dev] [PATCH v4] " Laurent Hardy
2017-04-28 0:43 ` Dai, Wei
2017-04-28 5:23 ` Ferruh Yigit
2017-05-17 13:31 ` Roger B Melton
2017-05-22 18:54 ` [dpdk-dev] 2nd try: problem with ixgbe_dev_link_update() for multi-speed fiber [was] " Roger B. Melton
2017-05-23 7:24 ` Dai, Wei
2017-05-23 7:41 ` Dai, Wei
2017-05-24 14:40 ` Roger B. Melton
2017-05-24 18:38 ` Roger B. Melton
2017-06-02 16:15 ` Roger B. Melton
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=49759EB36A64CF4892C1AFEC9231E8D650A23CB0@PGSMSX101.gar.corp.intel.com \
--to=wei.dai@intel.com \
--cc=dev@dpdk.org \
--cc=helin.zhang@intel.com \
--cc=konstantin.ananyev@intel.com \
--cc=laurent.hardy@6wind.com \
--cc=olivier.matz@6wind.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).