From: Jiawen Wu <jiawenwu@trustnetic.com>
To: dev@dpdk.org
Cc: Jiawen Wu <jiawenwu@trustnetic.com>
Subject: [dpdk-dev] [PATCH v4 37/58] net/txgbe: add SWFW semaphore and lock
Date: Mon, 19 Oct 2020 16:53:54 +0800 [thread overview]
Message-ID: <20201019085415.82207-38-jiawenwu@trustnetic.com> (raw)
In-Reply-To: <20201019085415.82207-1-jiawenwu@trustnetic.com>
Add semaphore between software and firmware.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
drivers/net/txgbe/base/txgbe_dummy.h | 2 +-
drivers/net/txgbe/base/txgbe_eeprom.h | 8 ++
drivers/net/txgbe/base/txgbe_hw.c | 129 ++++++++++++++++++++++++++
drivers/net/txgbe/base/txgbe_hw.h | 5 +
drivers/net/txgbe/base/txgbe_type.h | 2 +-
drivers/net/txgbe/txgbe_ethdev.c | 29 ++++++
6 files changed, 173 insertions(+), 2 deletions(-)
diff --git a/drivers/net/txgbe/base/txgbe_dummy.h b/drivers/net/txgbe/base/txgbe_dummy.h
index 495daa18a..0a3a76d0c 100644
--- a/drivers/net/txgbe/base/txgbe_dummy.h
+++ b/drivers/net/txgbe/base/txgbe_dummy.h
@@ -326,7 +326,7 @@ static inline void txgbe_mac_fc_autoneg_dummy(struct txgbe_hw *TUP0)
{
}
static inline s32 txgbe_mac_set_fw_drv_ver_dummy(struct txgbe_hw *TUP0, u8 TUP1,
- u8 TUP2, u8 TUP3, u8 TUP4, u16 TUP5, char *TUP6)
+ u8 TUP2, u8 TUP3, u8 TUP4, u16 TUP5, const char *TUP6)
{
return TXGBE_ERR_OPS_DUMMY;
}
diff --git a/drivers/net/txgbe/base/txgbe_eeprom.h b/drivers/net/txgbe/base/txgbe_eeprom.h
index 2ad6c7e19..d0e142dba 100644
--- a/drivers/net/txgbe/base/txgbe_eeprom.h
+++ b/drivers/net/txgbe/base/txgbe_eeprom.h
@@ -30,6 +30,14 @@
#define TXGBE_FW_LESM_PARAMETERS_PTR 0x2
#define TXGBE_FW_LESM_STATE_1 0x1
#define TXGBE_FW_LESM_STATE_ENABLED 0x8000 /* LESM Enable bit */
+#define TXGBE_ALT_SAN_MAC_ADDR_BLK_PTR 0x27 /* Alt. SAN MAC block */
+#define TXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET 0x0 /* Alt SAN MAC capability */
+#define TXGBE_ALT_SAN_MAC_ADDR_PORT0_OFFSET 0x1 /* Alt SAN MAC 0 offset */
+#define TXGBE_ALT_SAN_MAC_ADDR_PORT1_OFFSET 0x4 /* Alt SAN MAC 1 offset */
+#define TXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET 0x7 /* Alt WWNN prefix offset */
+#define TXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET 0x8 /* Alt WWPN prefix offset */
+#define TXGBE_ALT_SAN_MAC_ADDR_CAPS_SANMAC 0x0 /* Alt SAN MAC exists */
+#define TXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN 0x1 /* Alt WWN base exists */
s32 txgbe_init_eeprom_params(struct txgbe_hw *hw);
s32 txgbe_calc_eeprom_checksum(struct txgbe_hw *hw);
diff --git a/drivers/net/txgbe/base/txgbe_hw.c b/drivers/net/txgbe/base/txgbe_hw.c
index f3524ec2b..1b1d1525f 100644
--- a/drivers/net/txgbe/base/txgbe_hw.c
+++ b/drivers/net/txgbe/base/txgbe_hw.c
@@ -670,6 +670,77 @@ s32 txgbe_update_mc_addr_list(struct txgbe_hw *hw, u8 *mc_addr_list,
return 0;
}
+/**
+ * txgbe_acquire_swfw_sync - Acquire SWFW semaphore
+ * @hw: pointer to hardware structure
+ * @mask: Mask to specify which semaphore to acquire
+ *
+ * Acquires the SWFW semaphore through the MNGSEM register for the specified
+ * function (CSR, PHY0, PHY1, EEPROM, Flash)
+ **/
+s32 txgbe_acquire_swfw_sync(struct txgbe_hw *hw, u32 mask)
+{
+ u32 mngsem = 0;
+ u32 swmask = TXGBE_MNGSEM_SW(mask);
+ u32 fwmask = TXGBE_MNGSEM_FW(mask);
+ u32 timeout = 200;
+ u32 i;
+
+ DEBUGFUNC("txgbe_acquire_swfw_sync");
+
+ for (i = 0; i < timeout; i++) {
+ /*
+ * SW NVM semaphore bit is used for access to all
+ * SW_FW_SYNC bits (not just NVM)
+ */
+ if (txgbe_get_eeprom_semaphore(hw))
+ return TXGBE_ERR_SWFW_SYNC;
+
+ mngsem = rd32(hw, TXGBE_MNGSEM);
+ if (mngsem & (fwmask | swmask)) {
+ /* Resource is currently in use by FW or SW */
+ txgbe_release_eeprom_semaphore(hw);
+ msec_delay(5);
+ } else {
+ mngsem |= swmask;
+ wr32(hw, TXGBE_MNGSEM, mngsem);
+ txgbe_release_eeprom_semaphore(hw);
+ return 0;
+ }
+ }
+
+ /* If time expired clear the bits holding the lock and retry */
+ if (mngsem & (fwmask | swmask))
+ txgbe_release_swfw_sync(hw, mngsem & (fwmask | swmask));
+
+ msec_delay(5);
+ return TXGBE_ERR_SWFW_SYNC;
+}
+
+/**
+ * txgbe_release_swfw_sync - Release SWFW semaphore
+ * @hw: pointer to hardware structure
+ * @mask: Mask to specify which semaphore to release
+ *
+ * Releases the SWFW semaphore through the MNGSEM register for the specified
+ * function (CSR, PHY0, PHY1, EEPROM, Flash)
+ **/
+void txgbe_release_swfw_sync(struct txgbe_hw *hw, u32 mask)
+{
+ u32 mngsem;
+ u32 swmask = mask;
+
+ DEBUGFUNC("txgbe_release_swfw_sync");
+
+ txgbe_get_eeprom_semaphore(hw);
+
+ mngsem = rd32(hw, TXGBE_MNGSEM);
+ mngsem &= ~swmask;
+ wr32(hw, TXGBE_MNGSEM, mngsem);
+
+ txgbe_release_eeprom_semaphore(hw);
+}
+
/**
* txgbe_disable_sec_rx_path - Stops the receive data path
* @hw: pointer to hardware structure
@@ -1047,6 +1118,60 @@ s32 txgbe_check_mac_link(struct txgbe_hw *hw, u32 *speed,
return 0;
}
+/**
+ * txgbe_get_wwn_prefix - Get alternative WWNN/WWPN prefix from
+ * the EEPROM
+ * @hw: pointer to hardware structure
+ * @wwnn_prefix: the alternative WWNN prefix
+ * @wwpn_prefix: the alternative WWPN prefix
+ *
+ * This function will read the EEPROM from the alternative SAN MAC address
+ * block to check the support for the alternative WWNN/WWPN prefix support.
+ **/
+s32 txgbe_get_wwn_prefix(struct txgbe_hw *hw, u16 *wwnn_prefix,
+ u16 *wwpn_prefix)
+{
+ u16 offset, caps;
+ u16 alt_san_mac_blk_offset;
+
+ DEBUGFUNC("txgbe_get_wwn_prefix");
+
+ /* clear output first */
+ *wwnn_prefix = 0xFFFF;
+ *wwpn_prefix = 0xFFFF;
+
+ /* check if alternative SAN MAC is supported */
+ offset = TXGBE_ALT_SAN_MAC_ADDR_BLK_PTR;
+ if (hw->rom.readw_sw(hw, offset, &alt_san_mac_blk_offset))
+ goto wwn_prefix_err;
+
+ if (alt_san_mac_blk_offset == 0 || alt_san_mac_blk_offset == 0xFFFF)
+ goto wwn_prefix_out;
+
+ /* check capability in alternative san mac address block */
+ offset = alt_san_mac_blk_offset + TXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET;
+ if (hw->rom.read16(hw, offset, &caps))
+ goto wwn_prefix_err;
+ if (!(caps & TXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN))
+ goto wwn_prefix_out;
+
+ /* get the corresponding prefix for WWNN/WWPN */
+ offset = alt_san_mac_blk_offset + TXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET;
+ if (hw->rom.read16(hw, offset, wwnn_prefix))
+ DEBUGOUT("eeprom read at offset %d failed", offset);
+
+ offset = alt_san_mac_blk_offset + TXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET;
+ if (hw->rom.read16(hw, offset, wwpn_prefix))
+ goto wwn_prefix_err;
+
+wwn_prefix_out:
+ return 0;
+
+wwn_prefix_err:
+ DEBUGOUT("eeprom read at offset %d failed", offset);
+ return 0;
+}
+
/**
* txgbe_get_device_caps - Get additional device capabilities
* @hw: pointer to hardware structure
@@ -1605,6 +1730,8 @@ s32 txgbe_init_ops_pf(struct txgbe_hw *hw)
mac->enable_rx_dma = txgbe_enable_rx_dma_raptor;
mac->get_mac_addr = txgbe_get_mac_addr;
mac->stop_hw = txgbe_stop_hw;
+ mac->acquire_swfw_sync = txgbe_acquire_swfw_sync;
+ mac->release_swfw_sync = txgbe_release_swfw_sync;
mac->reset_hw = txgbe_reset_hw;
mac->disable_sec_rx_path = txgbe_disable_sec_rx_path;
@@ -1614,6 +1741,7 @@ s32 txgbe_init_ops_pf(struct txgbe_hw *hw)
mac->get_san_mac_addr = txgbe_get_san_mac_addr;
mac->set_san_mac_addr = txgbe_set_san_mac_addr;
mac->get_device_caps = txgbe_get_device_caps;
+ mac->get_wwn_prefix = txgbe_get_wwn_prefix;
mac->autoc_read = txgbe_autoc_read;
mac->autoc_write = txgbe_autoc_write;
@@ -1630,6 +1758,7 @@ s32 txgbe_init_ops_pf(struct txgbe_hw *hw)
mac->check_link = txgbe_check_mac_link;
/* Manageability interface */
+ mac->set_fw_drv_ver = txgbe_hic_set_drv_ver;
mac->get_thermal_sensor_data = txgbe_get_thermal_sensor_data;
mac->init_thermal_sensor_thresh = txgbe_init_thermal_sensor_thresh;
diff --git a/drivers/net/txgbe/base/txgbe_hw.h b/drivers/net/txgbe/base/txgbe_hw.h
index ac4f7fbe8..cba5876e8 100644
--- a/drivers/net/txgbe/base/txgbe_hw.h
+++ b/drivers/net/txgbe/base/txgbe_hw.h
@@ -29,6 +29,8 @@ s32 txgbe_disable_sec_tx_path(struct txgbe_hw *hw);
s32 txgbe_enable_sec_tx_path(struct txgbe_hw *hw);
s32 txgbe_validate_mac_addr(u8 *mac_addr);
+s32 txgbe_acquire_swfw_sync(struct txgbe_hw *hw, u32 mask);
+void txgbe_release_swfw_sync(struct txgbe_hw *hw, u32 mask);
s32 txgbe_get_san_mac_addr(struct txgbe_hw *hw, u8 *san_mac_addr);
s32 txgbe_set_san_mac_addr(struct txgbe_hw *hw, u8 *san_mac_addr);
@@ -39,6 +41,9 @@ s32 txgbe_check_mac_link(struct txgbe_hw *hw,
u32 *speed,
bool *link_up, bool link_up_wait_to_complete);
+s32 txgbe_get_wwn_prefix(struct txgbe_hw *hw, u16 *wwnn_prefix,
+ u16 *wwpn_prefix);
+
s32 txgbe_get_device_caps(struct txgbe_hw *hw, u16 *device_caps);
void txgbe_clear_tx_pending(struct txgbe_hw *hw);
diff --git a/drivers/net/txgbe/base/txgbe_type.h b/drivers/net/txgbe/base/txgbe_type.h
index dc038a5ba..539d1fb4d 100644
--- a/drivers/net/txgbe/base/txgbe_type.h
+++ b/drivers/net/txgbe/base/txgbe_type.h
@@ -483,7 +483,7 @@ struct txgbe_mac_info {
/* Manageability interface */
s32 (*set_fw_drv_ver)(struct txgbe_hw *hw, u8 maj, u8 min, u8 build,
- u8 ver, u16 len, char *driver_ver);
+ u8 ver, u16 len, const char *driver_ver);
s32 (*get_thermal_sensor_data)(struct txgbe_hw *hw);
s32 (*init_thermal_sensor_thresh)(struct txgbe_hw *hw);
void (*get_rtrup2tc)(struct txgbe_hw *hw, u8 *map);
diff --git a/drivers/net/txgbe/txgbe_ethdev.c b/drivers/net/txgbe/txgbe_ethdev.c
index 30dd922be..f6154cd04 100644
--- a/drivers/net/txgbe/txgbe_ethdev.c
+++ b/drivers/net/txgbe/txgbe_ethdev.c
@@ -336,6 +336,29 @@ txgbe_dev_queue_stats_mapping_set(struct rte_eth_dev *eth_dev,
return 0;
}
+/*
+ * Ensure that all locks are released before first NVM or PHY access
+ */
+static void
+txgbe_swfw_lock_reset(struct txgbe_hw *hw)
+{
+ uint16_t mask;
+
+ /*
+ * These ones are more tricky since they are common to all ports; but
+ * swfw_sync retries last long enough (1s) to be almost sure that if
+ * lock can not be taken it is due to an improper lock of the
+ * semaphore.
+ */
+ mask = TXGBE_MNGSEM_SWPHY |
+ TXGBE_MNGSEM_SWMBX |
+ TXGBE_MNGSEM_SWFLASH;
+ if (hw->mac.acquire_swfw_sync(hw, mask) < 0)
+ PMD_DRV_LOG(DEBUG, "SWFW common locks released");
+
+ hw->mac.release_swfw_sync(hw, mask);
+}
+
static int
eth_txgbe_dev_init(struct rte_eth_dev *eth_dev, void *init_params __rte_unused)
{
@@ -404,6 +427,9 @@ eth_txgbe_dev_init(struct rte_eth_dev *eth_dev, void *init_params __rte_unused)
return -EIO;
}
+ /* Unlock any pending hardware semaphore */
+ txgbe_swfw_lock_reset(hw);
+
err = hw->rom.init_params(hw);
if (err != 0) {
PMD_INIT_LOG(ERR, "The EEPROM init failed: %d", err);
@@ -1454,6 +1480,9 @@ txgbe_dev_close(struct rte_eth_dev *dev)
dev->rx_pkt_burst = NULL;
dev->tx_pkt_burst = NULL;
+ /* Unlock any pending hardware semaphore */
+ txgbe_swfw_lock_reset(hw);
+
/* disable uio intr before callback unregister */
rte_intr_disable(intr_handle);
--
2.18.4
next prev parent reply other threads:[~2020-10-19 9:08 UTC|newest]
Thread overview: 84+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-19 8:53 [dpdk-dev] [PATCH v4 00/58] net: txgbe PMD Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 01/58] net/txgbe: add build and doc infrastructure Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 02/58] net/txgbe: add ethdev probe and remove Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 03/58] net/txgbe: add device init and uninit Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 04/58] net/txgbe: add error types and registers Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 05/58] net/txgbe: add MAC type and bus lan id Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 06/58] net/txgbe: add HW infrastructure and dummy function Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 07/58] net/txgbe: add EEPROM functions Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 08/58] net/txgbe: add HW init and reset operation Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 09/58] net/txgbe: add PHY init Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 10/58] net/txgbe: add module identify Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 11/58] net/txgbe: add PHY reset Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 12/58] net/txgbe: add info get operation Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 13/58] net/txgbe: add interrupt operation Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 14/58] net/txgbe: add device configure operation Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 15/58] net/txgbe: add link status change Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 16/58] net/txgbe: add multi-speed link setup Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 17/58] net/txgbe: add autoc read and write Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 18/58] net/txgbe: add MAC address operations Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 19/58] net/txgbe: add unicast hash bitmap Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 20/58] net/txgbe: add Rx and Tx init Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 21/58] net/txgbe: add Rx and Tx queues setup and release Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 22/58] net/txgbe: add Rx and Tx start and stop Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 23/58] net/txgbe: add packet type Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 24/58] net/txgbe: fill simple transmit function Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 25/58] net/txgbe: fill transmit function with hardware offload Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 26/58] net/txgbe: fill Tx prepare function Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 27/58] net/txgbe: fill receive functions Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 28/58] net/txgbe: add device start operation Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 29/58] net/txgbe: add Rx and Tx data path start and stop Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 30/58] net/txgbe: add device stop and close operations Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 31/58] net/txgbe: support Rx interrupt Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 32/58] net/txgbe: add Rx and Tx queue info get Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 33/58] net/txgbe: add device stats get Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 34/58] net/txgbe: add device xstats get Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 35/58] net/txgbe: add queue stats mapping Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 36/58] net/txgbe: add VLAN handle support Jiawen Wu
2020-10-19 8:53 ` Jiawen Wu [this message]
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 38/58] net/txgbe: add PF module init and uninit for SRIOV Jiawen Wu
2020-10-26 14:54 ` Ferruh Yigit
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 39/58] net/txgbe: add process mailbox operation Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 40/58] net/txgbe: add PF module configure for SRIOV Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 41/58] net/txgbe: add VMDq configure Jiawen Wu
2020-10-19 8:53 ` [dpdk-dev] [PATCH v4 42/58] net/txgbe: add RSS support Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 43/58] net/txgbe: add DCB support Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 44/58] net/txgbe: add flow control support Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 45/58] net/txgbe: add FC auto negotiation support Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 46/58] net/txgbe: add priority flow control support Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 47/58] net/txgbe: add device promiscuous and allmulticast mode Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 48/58] net/txgbe: add MTU set operation Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 49/58] net/txgbe: add FW version get operation Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 50/58] net/txgbe: add EEPROM info " Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 51/58] net/txgbe: add register dump support Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 52/58] net/txgbe: support device LED on and off Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 53/58] net/txgbe: add mirror rule operations Jiawen Wu
2020-10-26 14:54 ` Ferruh Yigit
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 54/58] net/txgbe: add PTP support Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 55/58] net/txgbe: add DCB info get operation Jiawen Wu
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 56/58] net/txgbe: add Rx and Tx descriptor status Jiawen Wu
2020-10-26 14:54 ` Ferruh Yigit
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 57/58] net/txgbe: change stop operation callback to return int Jiawen Wu
2020-10-26 14:55 ` Ferruh Yigit
2020-10-19 8:54 ` [dpdk-dev] [PATCH v4 58/58] net/txgbe: introduce log type in the driver documentation Jiawen Wu
2020-10-26 14:55 ` Ferruh Yigit
2020-10-22 11:23 ` [dpdk-dev] [PATCH v4 00/58] net: txgbe PMD Jiawen Wu
2020-10-22 11:44 ` Ferruh Yigit
2020-10-26 14:55 ` Ferruh Yigit
2020-10-27 2:39 ` Jiawen Wu
2020-10-27 11:37 ` Ferruh Yigit
2020-11-03 23:08 ` Thomas Monjalon
2020-11-04 17:24 ` Ferruh Yigit
2020-11-05 1:55 ` Jiawen Wu
2020-11-05 8:55 ` Jiawen Wu
2020-11-05 9:28 ` Thomas Monjalon
2020-11-06 6:28 ` Honnappa Nagarahalli
2020-11-06 9:22 ` Jiawen Wu
2020-11-06 17:36 ` Honnappa Nagarahalli
2020-11-06 18:21 ` Honnappa Nagarahalli
2020-11-06 19:00 ` Thomas Monjalon
2020-11-06 19:56 ` Honnappa Nagarahalli
2020-11-07 9:55 ` Thomas Monjalon
2020-10-27 8:48 ` David Marchand
2020-10-27 11:36 ` Ferruh Yigit
2020-10-27 11:39 ` David Marchand
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201019085415.82207-38-jiawenwu@trustnetic.com \
--to=jiawenwu@trustnetic.com \
--cc=dev@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).